Bhagavathi Perumal S [Thu, 20 Dec 2018 12:26:00 +0000 (14:26 +0200)]
ath10k: add support to configure BB timing over wmi
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bhagavathi Perumal S [Thu, 20 Dec 2018 12:25:43 +0000 (14:25 +0200)]
dt-bindings: net: ath10k: add new dt entry to identify external FEM
This adds new dt entry ext-fem-name, it is used by ath10k driver
to select correct timing parameters and configure it in target wifi hardware.
The Front End Module(FEM) normally includes tx power amplifier(PA) and
rx low noise amplifier(LNA). The default timing parameters like tx end to
PA off timing values were fine tuned for internal FEM used in reference
design. And these timing values can not be same if ODM modifies hardware
design with different external FEM. This DT entry helps to choose correct
timing values in driver if different external FEM hardware used.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bhagavathi Perumal S [Thu, 20 Dec 2018 12:25:32 +0000 (14:25 +0200)]
dt-bindings: net: ath10k: fix node name and device type in qcom ath10k example
In qcom,ath10k documentation, ath10k is used as node name in the example of
pci based device. Normally, node name should be class of device and not the
model name, so fix it to node name "wifi". And remove the property device_type
pci since only pci bridges should have this property.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhi Chen [Thu, 20 Dec 2018 12:25:18 +0000 (14:25 +0200)]
ath10k: fix tx_stats memory leak
Memory of tx_stats was allocated when a STA was added. But it's not freed
if the STA failed to be added to driver. This issue could be seen in MDK3
attack case when STA number reached the limit.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Zhi Chen [Thu, 20 Dec 2018 12:24:43 +0000 (14:24 +0200)]
ath10k: fix peer stats null pointer dereference
There was a race condition in SMP that an ath10k_peer was created but its
member sta was null. Following are procedures of ath10k_peer creation and
member sta access in peer statistics path.
1. Peer creation:
ath10k_peer_create()
=>ath10k_wmi_peer_create()
=>ath10k_wait_for_peer_created()
...
# another kernel path, RX from firmware
ath10k_htt_t2h_msg_handler()
=>ath10k_peer_map_event()
=>wake_up()
# ar->peer_map[id] = peer //add peer to map
#wake up original path from waiting
...
# peer->sta = sta //sta assignment
2. RX path of statistics
ath10k_htt_t2h_msg_handler()
=>ath10k_update_per_peer_tx_stats()
=>ath10k_htt_fetch_peer_stats()
# peer->sta //sta accessing
Any access of peer->sta after peer was added to peer_map but before sta was
assigned could cause a null pointer issue. And because these two steps are
asynchronous, no proper lock can protect them. So both peer and sta need to
be checked before access.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00005
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 12:24:23 +0000 (14:24 +0200)]
dt: bindings: ath10k: add bindings for wifi iommu node
WCN3990 wifi module can optionally make use of the IOMMU.
Add binding documentation for phandle to the IOMMU and
the stream id of wifi iommu block.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 12:24:10 +0000 (14:24 +0200)]
dt: bindings: ath10k: add missing dt properties for WCN3990 wifi node
Add missing optional properties in WCN3990 wifi node.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Thu, 20 Dec 2018 07:53:45 +0000 (09:53 +0200)]
ath10k: remove an unnecessary NULL check
The "survey" pointer is the address of an array element. We know that
it can't be NULL so this check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 07:53:43 +0000 (09:53 +0200)]
ath10k: move non-fatal warn logs to dbg level
During driver load below warn logs are printed in the console.
Since driver may not implement all wmi events sent by fw and
all of them are non-fatal, move this log to debug level to
remove un-necessary warn message on console.
[ 361.887230] ath10k_snoc a000000.wifi: Unknown eventid: 16393
[ 361.907037] ath10k_snoc a000000.wifi: Unknown eventid: 237569
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Dan Carpenter [Thu, 20 Dec 2018 07:53:41 +0000 (09:53 +0200)]
ath10k: fix a NULL vs IS_ERR() check
The devm_memremap() function doesn't return NULLs, it returns error
pointers.
Fixes:
ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Govind Singh [Thu, 20 Dec 2018 07:53:36 +0000 (09:53 +0200)]
ath10k: remove work in progress logs from snoc driver
All the necessary patches to make wifi running (over SNOC)
are merged and tested on SDM845/QCS404 platform with WCN3990
wifi module, hence remove work in progress debug from snoc
driver and Kconfig.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bhagavathi Perumal S [Thu, 20 Dec 2018 07:53:34 +0000 (09:53 +0200)]
ath10k: fix warning due to msdu limit error
Some hardwares variants (QCA99x0) are limiting msdu deaggregation with
some threshold value(default limit in QCA99x0 is 64 msdus), it was introduced to
avoid excessive MSDU-deaggregation in error cases. When number of sub frames
exceeds the limit, target hardware will send all msdus starting from present
msdu in RAW format as a single msdu packet and it will be indicated with
error status bit "RX_MSDU_END_INFO0_MSDU_LIMIT_ERR" set in rx descriptor.
This msdu frame is a partial raw MSDU and does't have first msdu and ieee80211
header. It caused below warning message.
[ 320.151332] ------------[ cut here ]------------
[ 320.155006] WARNING: CPU: 0 PID: 3 at drivers/net/wireless/ath/ath10k/htt_rx.c:1188
In our issue case, MSDU limit error happened due to FCS error and generated
this warning message.
This fixes the warning by handling the MSDU limit error. If msdu limit error
happens, driver adds first MSDU's ieee80211 header and sets A-MSDU present bit
in QOS header so that upper layer processes this frame if it is valid or drop it
if FCS error set. And removed the warning message, hence partial msdus without
first msdu is expected in msdu limit error cases.
Tested on QCA9984, Firmware 10.4-3.6-00104
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sathishkumar Muruganandam [Thu, 20 Dec 2018 07:53:30 +0000 (09:53 +0200)]
ath10k: disable 4addr source port learning in 10.4 FW by default
Currently in 10.4 FW, all the received 4addr frames are processed for
source port learning which is enabled by default. This learning can't be
disabled by default in FW since it breaks backward compatibility.
Since ath10k uses mac80211 based 4addr mode, source port learning done in
10.4 FW is redundant and also causes issues when 3addr frames are
transmitted/received for a 4addr station.
One such visible functional impact is when GTK rekey frame from
hostapd based AP to 4addr STA is dropped in AP's 10.4 FW. This is since
GTK rekey EAPOL frame is 3addr frame on AP interface and STA enabled
with 4addr is already allowed for receiving 3addr EAPOL frames.
Source port learning implementation in 10.4 FW drops this 3addr GTK rekey
frame in AP destinated for 4addr STA causing disassociation and
re-association for every GTK rekey session. GTK rekey issue is not seen
when learning is disabled in FW.
To prevent such issues without breaking backward compatibility, FW
advertises new service bit making the source port learning configurable and
this learning is being currently disabled during ath10k vdev creation.
* Tested HW: QCA9984
* Tested FW: 10.4-3.6.0.1-00004
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Anilkumar Kolli [Thu, 20 Dec 2018 07:53:28 +0000 (09:53 +0200)]
ath10k: report tx rate using ieee80211_tx_rate_update()
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yu Wang [Thu, 20 Dec 2018 07:53:26 +0000 (09:53 +0200)]
ath10k: add amsdu support for monitor mode
When processing HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND, if the length of a msdu
is larger than the tailroom of the rx skb, skb_over_panic issue will happen
when calling skb_put. In monitor mode, amsdu will be handled in this path, and
msdu_len of the first msdu_desc is the length of the entire amsdu, which might
be larger than the maximum length of a skb, in such case, it will hit the issue
upon.
To fix this issue, process msdu list separately for monitor mode.
Successfully tested with:
QCA6174 (FW version: RM.4.4.1.c2-00057-QCARMSWP-1).
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
[kvalo@codeaurora.org: cosmetic cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Karthikeyan Periyasamy [Thu, 20 Dec 2018 07:53:17 +0000 (09:53 +0200)]
ath10k: fix kernel panic due to use after free
This issue arise in a race condition between ath10k_sta_state() and
ath10k_htt_fetch_peer_stats(), explained in below scenario
Steps:
1. In ath10k_sta_state(), arsta->tx_stats get deallocated before peer deletion
when the station moves from IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST
state.
2. Meanwhile ath10k receive HTT_T2H_MSG_TYPE_PEER_STATS message.
In ath10k_htt_fetch_peer_stats(), arsta->tx_stats get accessed after
the peer validation check.
Since arsta->tx_stats get freed before the peer deletion [1].
ath10k_htt_fetch_peer_stats() ended up in "use after free" situation.
Fixed this issue by moving the arsta->tx_stats free handling after the
peer deletion. so that ath10k_htt_fetch_peer_stats() will not end up in
"use after free" situation.
Kernel Panic:
Unable to handle kernel NULL pointer dereference at virtual address
00000286
pgd =
d8754000
[
00000286] *pgd=
00000000
Internal error: Oops: 5 [#1] PREEMPT SMP ARM
...
CPU: 0 PID: 6245 Comm: hostapd Not tainted
task:
dc44cac0 ti:
d4a38000 task.ti:
d4a38000
PC is at kmem_cache_alloc+0x7c/0x114
LR is at ath10k_sta_state+0x190/0xd58 [ath10k_core]
pc : [<
c02bdc50>] lr : [<
bf916b78>] psr:
20000013
sp :
d4a39b88 ip :
00000000 fp :
00000001
r10:
00000000 r9 :
1d3bc000 r8 :
00000dc0
r7 :
000080d0 r6 :
d4a38000 r5 :
dd401b00 r4 :
00000286
r3 :
00000000 r2 :
d4a39ba0 r1 :
000080d0 r0 :
dd401b00
Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control:
10c5787d Table:
5a75406a DAC:
00000015
Process hostapd (pid: 6245, stack limit = 0xd4a38238)
Stack: (0xd4a39b88 to 0xd4a3a000)
...
[<
c02bdc50>] (kmem_cache_alloc) from [<
bf916b78>] (ath10k_sta_state+0x190/0xd58 [ath10k_core])
[<
bf916b78>] (ath10k_sta_state [ath10k_core]) from [<
bf870d4c>] (sta_info_insert_rcu+0x418/0x61c [mac80211])
[<
bf870d4c>] (sta_info_insert_rcu [mac80211]) from [<
bf88634c>] (ieee80211_add_station+0xf0/0x134 [mac80211])
[<
bf88634c>] (ieee80211_add_station [mac80211]) from [<
bf83f3c4>] (nl80211_new_station+0x330/0x36c [cfg80211])
[<
bf83f3c4>] (nl80211_new_station [cfg80211]) from [<
bf6c4040>] (extack_doit+0x2c/0x74 [compat])
[<
bf6c4040>] (extack_doit [compat]) from [<
c05c285c>] (genl_rcv_msg+0x274/0x30c)
[<
c05c285c>] (genl_rcv_msg) from [<
c05c1d98>] (netlink_rcv_skb+0x58/0xac)
[<
c05c1d98>] (netlink_rcv_skb) from [<
c05c25d4>] (genl_rcv+0x20/0x34)
[<
c05c25d4>] (genl_rcv) from [<
c05c1750>] (netlink_unicast+0x11c/0x204)
[<
c05c1750>] (netlink_unicast) from [<
c05c1be0>] (netlink_sendmsg+0x30c/0x370)
[<
c05c1be0>] (netlink_sendmsg) from [<
c0587e90>] (sock_sendmsg+0x70/0x84)
[<
c0587e90>] (sock_sendmsg) from [<
c058970c>] (___sys_sendmsg.part.3+0x188/0x228)
[<
c058970c>] (___sys_sendmsg.part.3) from [<
c058a594>] (__sys_sendmsg+0x4c/0x70)
[<
c058a594>] (__sys_sendmsg) from [<
c0208c80>] (ret_fast_syscall+0x0/0x44)
Code:
ebfffec1 e1a04000 ea00001b e5953014 (
e7940003)
ath10k_pci 0000:01:00.0: SWBA overrun on vdev 0, skipped old beacon
Hardware tested: QCA9984
Firmware tested: 10.4-3.6.0.1-00004
Fixes:
a904417fc ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Thu, 20 Dec 2018 07:53:10 +0000 (09:53 +0200)]
ath10k: remove set but not used variable 'num_tdls_vifs'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/mac.c: In function 'ath10k_sta_state':
drivers/net/wireless/ath/ath10k/mac.c:6238:7: warning:
variable 'num_tdls_vifs' set but not used [-Wunused-but-set-variable]
'num_tdls_vifs' not used any more after
9a993cc1ea95 ("ath10k: fix the logic of limiting tdls peer counts")
Also, remove the single called function ath10k_mac_tdls_vifs_count
and ath10k_mac_tdls_vifs_count_iter.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
YueHaibing [Wed, 5 Dec 2018 07:59:03 +0000 (07:59 +0000)]
wil6210: remove set but not used variable 'wdev'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/wil6210/main.c: In function '_wil6210_disconnect':
drivers/net/wireless/ath/wil6210/main.c:407:23: warning:
variable 'wdev' set but not used [-Wunused-but-set-variable]
It never used since commit ("
e1b43407c034 wil6210: refactor disconnect flow")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yangtao Li [Mon, 3 Dec 2018 13:25:57 +0000 (08:25 -0500)]
wil6210: convert to DEFINE_SHOW_ATTRIBUTE
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kyle Roeschley [Wed, 5 Dec 2018 07:43:16 +0000 (09:43 +0200)]
ath6kl: Use debug instead of error message when disabled
This is not an unexpected condition, so we don't need to be shouting to the
world about it.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kyle Roeschley [Wed, 5 Dec 2018 07:43:13 +0000 (09:43 +0200)]
ath6kl: Fix off by one error in scan completion
When ath6kl was reworked to share code between regular and scheduled scans
in commit
3b8ffc6a22ba ("ath6kl: Configure probed SSID list consistently"),
probed SSID entry changed from 1-index to 0-indexed. However,
ath6kl_cfg80211_scan_complete_event() was missed in that change. Fix its
indexing so that we correctly clear out the probed SSID list.
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Kyle Roeschley [Wed, 5 Dec 2018 07:43:11 +0000 (09:43 +0200)]
ath6kl: Only use match sets when firmware supports it
Commit
dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan")
merged the probed and matched SSID lists before sending them to the
firmware. In the process, it assumed match set support is always available
in ath6kl_set_probed_ssids, which breaks scans for hidden SSIDs. Now, check
that the firmware supports matching SSIDs in scheduled scans before setting
MATCH_SSID_FLAG.
Fixes:
dd45b7598f1c ("ath6kl: Include match ssid list in scheduled scan")
Signed-off-by: Kyle Roeschley <kyle.roeschley@ni.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Yangtao Li [Mon, 3 Dec 2018 14:34:11 +0000 (09:34 -0500)]
net: marvell: convert to DEFINE_SHOW_ATTRIBUTE
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangtao Li [Mon, 3 Dec 2018 14:26:38 +0000 (09:26 -0500)]
net: qca_spi: convert to DEFINE_SHOW_ATTRIBUTE
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangtao Li [Mon, 3 Dec 2018 14:22:09 +0000 (09:22 -0500)]
net: stmmac: convert to DEFINE_SHOW_ATTRIBUTE
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Yangtao Li [Mon, 3 Dec 2018 14:13:35 +0000 (09:13 -0500)]
nfp: convert to DEFINE_SHOW_ATTRIBUTE
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 4 Dec 2018 00:34:32 +0000 (16:34 -0800)]
Merge branch 'mlx4_core-cleanups'
Tariq Toukan says:
====================
mlx4_core cleanups
This patchset by Erez contains cleanups to the mlx4_core driver.
Patch 1 replaces -EINVAL with -EOPNOTSUPP for unsupported operations.
Patch 2 fixes some coding style issues.
Series generated against net-next commit:
97e6c858a26e net: usb: aqc111: Initialize wol_cfg with memset in aqc111_suspend
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Erez Alfasi [Sun, 2 Dec 2018 15:40:26 +0000 (17:40 +0200)]
net/mlx4_core: Fix several coding style errors
Fix 3 checkpatch errors within mlx4/main.c:
- Unnecessary mlx4_debug_level global variable initialization to 0.
- Prohibited space before comma.
- Whitespaces instead of tab.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erez Alfasi [Sun, 2 Dec 2018 15:40:25 +0000 (17:40 +0200)]
net/mlx4_core: Fix return codes of unsupported operations
Functions __set_port_type and mlx4_check_port_params returned
-EINVAL while the proper return code is -EOPNOTSUPP as a
result of an unsupported operation. All drivers should generate
this and all users should check for it when detecting an
unsupported functionality.
Signed-off-by: Erez Alfasi <ereza@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu [Sun, 2 Dec 2018 15:33:14 +0000 (16:33 +0100)]
net: phy: Also request modules for C45 IDs
Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.
Let's also request the modules for these IDs.
Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Tue, 4 Dec 2018 00:23:09 +0000 (16:23 -0800)]
Merge branch 'octeontx2-next'
Jerin Jacob says:
====================
octeontx2-af: NIX and NPC enhancements
This patchset is a continuation to earlier submitted four patch
series to add a new driver for Marvell's OcteonTX2 SOC's
Resource virtualization unit (RVU) admin function driver.
1. octeontx2-af: Add RVU Admin Function driver
https://www.spinics.net/lists/netdev/msg528272.html
2. octeontx2-af: NPA and NIX blocks initialization
https://www.spinics.net/lists/netdev/msg529163.html
3. octeontx2-af: NPC parser and NIX blocks initialization
https://www.spinics.net/lists/netdev/msg530252.html
4. octeontx2-af: NPC MCAM support and FLR handling
https://www.spinics.net/lists/netdev/msg534392.html
This patch series adds support for below
NPC block:
- Add NPC(mkex) profile support for various Key extraction configurations
NIX block:
- Enable dynamic RSS flow key algorithm configuration
- Enhancements on Rx checksum and error checks
- Add support for Tx packet marking support
- TL1 schedule queue allocation enhancements
- Add LSO format configuration mbox
- VLAN TPID configuration
- Skip multicast entry init for broadcast tables
v2:
- Rename FLOW_* to NIX_FLOW_* to avoid serious global namespace collisions,
as we have various FLOW_* definitions coming from
include/uapi/linux/pkt_cls.h for example.(David Miller)
- Pack the arguments of rvu_get_tl1_schqs() function
as 80 columns allows.(David Miller)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Vamsi Attunuru [Sun, 2 Dec 2018 12:47:49 +0000 (18:17 +0530)]
octeontx2-af: Enable mkex profile
The following set of NPC registers allow the driver to configure NPC
to generate different key value schemes to compare against packet
payload in MCAM search.
NPC_AF_INTF(0..1)_KEX_CFG
NPC_AF_KEX_LDATA(0..1)_FLAGS_CFG
NPC_AF_INTF(0..1)_LID(0..7)_LT(0..15)_LD(0..1)_CFG
NPC_AF_INTF(0..1)_LDATA(0..1)_FLAGS(0..15)_CFG
Currently, the AF driver populates these registers to
configure the default values to address the most common
use cases such as key generation for channel number + DMAC.
The secure firmware stores different configuration
value of these registers to enable different NPC use case
along with the name for the lookup.
Patch loads profile binary from secure firmware over
the exiting CGX mailbox interface and apply the profile.
AF driver shall fall back to the default configuration
in case of any errors.
The AF consumer driver can know the selected profile
on response to NPC_GET_KEX_CFG mailbox by introducing
mkex_pfl_name in the struct npc_get_kex_cfg_rsp.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Dabilpuram [Sun, 2 Dec 2018 12:47:48 +0000 (18:17 +0530)]
octeontx2-af: Add LSO format configuration mailbox
NIX_AF_LSO_FORMAT(0..31)_FIELD(0..7) register enables an SW defined
means to define LSO packet modification formats.
0..31 works as an index to choose the algorithm, On success, the mailbox
returns the index to the client of chosen LSO algorithm selection.
This index will be used in configuring the transmit descriptors.
Add mailbox interface to dynamically reserve and configure LSO format.
This commit also fixes 'sizem1' for NIX_LSOALG_TCP_FLAGS
to '1' i.e 2 Bytes.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vidhya Raman [Sun, 2 Dec 2018 12:47:47 +0000 (18:17 +0530)]
octeontx2-af: Add L3 and L4 packet verification mailbox
Adds mailbox support for L4 checksum verification
and L3 and L4 length verification configuration.
Signed-off-by: Vidhya Raman <vraman@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Dabilpuram [Sun, 2 Dec 2018 12:47:46 +0000 (18:17 +0530)]
octeontx2-af: Configure VLAN TPIDs
Setup TPID's for vlan0 and vlan1 for Tx VLAN insertion offloads.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Krzysztof Kanas [Sun, 2 Dec 2018 12:47:45 +0000 (18:17 +0530)]
octeontx2-af: Add support for Tx packet marking
NIX_AF_MARK_FORMAT(0..127)_CTL register enables an SW defined
means to mark/insert various data in the packet based on
final packet color from traffic shaping HW.
0..127 works as an index to choose the algorithm. On success,
the mailbox returns the index to the client.
Add NIX_MARK_FORMAT_CFG mailbox which reserves mark format based on
tuple (offset, y_mask, y_val, r_mask, r_val)
If the tuple is requested again for mark format that was already
reserved, then it will be reused. If not it will reserve a new entry
if space is available.
Also on AF init commonly used marker format such as VLAN DEI, IPv4
ECN, IPv4 DSCP are reserved for AF consumers.
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vamsi Attunuru [Sun, 2 Dec 2018 12:47:44 +0000 (18:17 +0530)]
octeontx2-af: Enable RSS with promiscuous mode
This patch adds support for enabling RSS in promiscuous mode
if RSS is already requested by the AF client.
Signed-off-by: Vamsi Attunuru <vamsi.attunuru@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerin Jacob [Sun, 2 Dec 2018 12:47:43 +0000 (18:17 +0530)]
octeontx2-af: Define all NIX_AF_RX_DEF_* registers
In order to support all NIX specific valid length errors and
checksum errors on Rx, Update all NIX_AF_RX_DEF_* registers.
Also sorted all registers in HRM definition order.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerin Jacob [Sun, 2 Dec 2018 12:47:42 +0000 (18:17 +0530)]
octeontx2-af: Enable inner IPv4 checksum and its error code
This patch enables the inner IPv4 checksum and
defines the error code for Rx inner and outer checksum errors.
Setting ERRCODE as 1 so that CQE descriptor can be embedded
valid checksum error code and the driver can interpret
checksum error as ERRLEV = LID + 1 and ERRCODE = 1.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Dabilpuram [Sun, 2 Dec 2018 12:47:41 +0000 (18:17 +0530)]
octeontx2-af: Allow freeing single TLx Tx schedule queue
The default behavior was to free all the TLx Tx schedule
queues. This patch adds support for freeing a single Tx
schedule queue if TXSCHQ_FREE_ALL flag is not set.
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nithin Dabilpuram [Sun, 2 Dec 2018 12:47:40 +0000 (18:17 +0530)]
octeontx2-af: Restrict TL1 allocation and configuration
TL1 is the root node in the scheduling hierarchy and
it is a global resource with a limited number.
This patch introduces restriction and validation on
the allocation of the TL1 nodes for the effective resource
sharing across the AF consumers.
- Limit TL1 allocation to 2 per lmac.
One could be for the normal link and one for IEEE802.3br
express link (Express Send DMA).
Effectively all the VF's of an RVU PF(lmac) share the two TL1 schqs.
- TL1 cannot be freed once allocated.
- Allow VF's to only apply default config to TL1 if not
already applied. PF's can always overwrite the TL1 config.
- Consider NIX_AQ_INSTOP_WRITE while validating txschq
when sq.ena is set.
Signed-off-by: Krzysztof Kanas <kkanas@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerin Jacob [Sun, 2 Dec 2018 12:47:39 +0000 (18:17 +0530)]
octeontx2-af: Add support for runtime RSS algo index reservation
Introduced reserve_flowkey_alg_idx()to reserve RSS algorithm index,
it would internally use set_flowkey_fields() to generate fields
based on the flow key dynamically.
On AF driver init, it would reserve a predefined set RSS algo indexes,
which will be available all the time for all the AF driver consumers.
The leftover algo indexes can be reserved at runtime through
exiting nix_rss_flowkey_cfg mailbox message.
The NIX_FLOW_KEY_TYPE_PORT is removed from predefined a set of RSS flow
type as it is not used by any consumer.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerin Jacob [Sun, 2 Dec 2018 12:47:38 +0000 (18:17 +0530)]
octeontx2-af: Add support for dynamic flow cfg to RSS field generation
Introduce state-based algorithm to convert the flow_key value
to RSS algo field used by NIX_AF_RX_FLOW_KEY_ALGX_FIELDX register.
The outer `for loop` goes over _all_ protocol field and the following
variables depict the state machine forward progress logic.
a) keyoff_marker - Enabled when hash byte length needs to be accounted
in field->key_offset update.
b) field_marker - Enabled when a new field needs to be selected.
c) group_member - Enabled when a protocol is part of a group.
This would remove the existing hard coding and enable to add
new protocol support seamlessly.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jerin Jacob [Sun, 2 Dec 2018 12:47:37 +0000 (18:17 +0530)]
octeontx2-af: Add response for RSS flow key cfg message
Added response for nix_rss_flowkey_cfg message to return
selected RSS algorithm index.
The FLOW_KEY_TYPE* definition is part of the mbox message and
it will be used by the other consumers of AF driver hence moving to mbox.h.
Also renamed FLOW_* definitions to NIX_FLOW_* to avoid global
name space collisions, as we have various coming from
include/uapi/linux/pkt_cls.h for example.
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham [Sun, 2 Dec 2018 12:47:36 +0000 (18:17 +0530)]
octeontx2-af: Skip NIXLF check for bcast MCE entry
At the time of initial broadcast packet replication table init,
NIXLFs are not yet attached to PF_FUNCs. Hence skipped checking
NIXLF while submitting MCE entry init instruction to NIX admin queue.
Also did a minor cleanup while installing bcast match entry in
packet parser unit i.e NPC.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Jerin Jacob <jerinj@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2018 23:58:33 +0000 (15:58 -0800)]
Merge branch 'udp-msg_zerocopy'
Willem de Bruijn says:
====================
udp msg_zerocopy
Enable MSG_ZEROCOPY for udp sockets
Patch 1/3 is the main patch, a rework of RFC patch
http://patchwork.ozlabs.org/patch/899630/
more details in the patch commit message
Patch 2/3 is an optimization to remove a branch from the UDP hot path
and refcount_inc/refcount_dec_and_test pair when zerocopy is used.
This used to be included in the first patch in v2.
Patch 3/3 runs the already existing udp zerocopy tests
as part of kselftest
See also recent Linux Plumbers presentation
https://linuxplumbersconf.org/event/2/contributions/106/attachments/104/128/willemdebruijn-lpc2018-udpgso-presentation-
20181113.pdf
Changes:
v1 -> v2
- Fixup reverse christmas tree violation
v2 -> v3
- Split refcount avoidance optimization into separate patch
- Fix refcount leak on error in fragmented case
(thanks to Paolo Abeni for pointing this one out!)
- Fix refcount inc on zero
v3 -> v4
- Move skb_zcopy_set below the only kfree_skb that might cause
a premature uarg destroy before skb_zerocopy_put_abort
- Move the entire skb_shinfo assignment block, to keep that
cacheline access in one place
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 30 Nov 2018 20:32:41 +0000 (15:32 -0500)]
selftests: extend zerocopy tests to udp
Both msg_zerocopy and udpgso_bench have udp zerocopy variants.
Exercise these as part of the standard kselftest run.
With udp, msg_zerocopy has no control channel. Ensure that the
receiver exits after the sender by accounting for the initial
delay in starting them (in msg_zerocopy.sh).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 30 Nov 2018 20:32:40 +0000 (15:32 -0500)]
udp: elide zerocopy operation in hot path
With MSG_ZEROCOPY, each skb holds a reference to a struct ubuf_info.
Release of its last reference triggers a completion notification.
The TCP stack in tcp_sendmsg_locked holds an extra ref independent of
the skbs, because it can build, send and free skbs within its loop,
possibly reaching refcount zero and freeing the ubuf_info too soon.
The UDP stack currently also takes this extra ref, but does not need
it as all skbs are sent after return from __ip(6)_append_data.
Avoid the extra refcount_inc and refcount_dec_and_test, and generally
the sock_zerocopy_put in the common path, by passing the initial
reference to the first skb.
This approach is taken instead of initializing the refcount to 0, as
that would generate error "refcount_t: increment on 0" on the
next skb_zcopy_set.
Changes
v3 -> v4
- Move skb_zcopy_set below the only kfree_skb that might cause
a premature uarg destroy before skb_zerocopy_put_abort
- Move the entire skb_shinfo assignment block, to keep that
cacheline access in one place
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn [Fri, 30 Nov 2018 20:32:39 +0000 (15:32 -0500)]
udp: msg_zerocopy
Extend zerocopy to udp sockets. Allow setting sockopt SO_ZEROCOPY and
interpret flag MSG_ZEROCOPY.
This patch was previously part of the zerocopy RFC patchsets. Zerocopy
is not effective at small MTU. With segmentation offload building
larger datagrams, the benefit of page flipping outweights the cost of
generating a completion notification.
tools/testing/selftests/net/msg_zerocopy.sh after applying follow-on
test patch and making skb_orphan_frags_rx same as skb_orphan_frags:
ipv4 udp -t 1
tx=191312 (11938 MB) txc=0 zc=n
rx=191312 (11938 MB)
ipv4 udp -z -t 1
tx=304507 (19002 MB) txc=304507 zc=y
rx=304507 (19002 MB)
ok
ipv6 udp -t 1
tx=174485 (10888 MB) txc=0 zc=n
rx=174485 (10888 MB)
ipv6 udp -z -t 1
tx=294801 (18396 MB) txc=294801 zc=y
rx=294801 (18396 MB)
ok
Changes
v1 -> v2
- Fixup reverse christmas tree violation
v2 -> v3
- Split refcount avoidance optimization into separate patch
- Fix refcount leak on error in fragmented case
(thanks to Paolo Abeni for pointing this one out!)
- Fix refcount inc on zero
- Test sock_flag SOCK_ZEROCOPY directly in __ip_append_data.
This is needed since commit
5cf4a8532c99 ("tcp: really ignore
MSG_ZEROCOPY if no SO_ZEROCOPY") did the same for tcp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2018 23:44:27 +0000 (15:44 -0800)]
Merge tag 'wireless-drivers-next-for-davem-2018-11-30' of git://git./linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2018 23:40:30 +0000 (15:40 -0800)]
Merge branch 'davinci_emac-read-the-MAC-address-from-nvmem'
Bartosz Golaszewski says:
====================
davinci_emac: read the MAC address from nvmem
This series is part of a bigger series that aims at removing the platform
data structure from the at24 EEPROM driver[1].
We provide a generalized version of of_get_nvmem_mac_address(), switch the
only user of the of_ variant to using it, remove the previous
implementation and use the new routine in the davinci_emac driver.
[1] https://lkml.org/lkml/2018/11/13/884
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski [Fri, 30 Nov 2018 08:21:00 +0000 (09:21 +0100)]
net: davinci_emac: use nvmem_get_mac_address()
All DaVinci boards still supported in board files now define nvmem
cells containing the MAC address. We want to stop using the setup
callback from at24 so the MAC address for those users will no longer
be provided over platform data. If we didn't get a valid MAC in pdata,
try nvmem before resorting to a random MAC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski [Fri, 30 Nov 2018 08:20:59 +0000 (09:20 +0100)]
of: net: kill of_get_nvmem_mac_address()
We've switched all users to nvmem_get_mac_address(). Remove the now
dead code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski [Fri, 30 Nov 2018 08:20:58 +0000 (09:20 +0100)]
net: cadence: switch to using nvmem_get_mac_address()
We now have a generalized helper routine to read the MAC address from
nvmem which takes struct device as argument. The nvmem subsystem will
then try device tree first before all other potential providers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bartosz Golaszewski [Fri, 30 Nov 2018 08:20:57 +0000 (09:20 +0100)]
net: ethernet: provide nvmem_get_mac_address()
We already have of_get_nvmem_mac_address() but some non-DT systems want
to read the MAC address from NVMEM too. Implement a generalized routine
that takes struct device as argument.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NeilBrown [Thu, 29 Nov 2018 23:26:50 +0000 (10:26 +1100)]
rhashtable: detect when object movement between tables might have invalidated a lookup
Some users of rhashtables might need to move an object from one table
to another - this appears to be the reason for the incomplete usage
of NULLS markers.
To support these, we store a unique NULLS_MARKER at the end of
each chain, and when a search fails to find a match, we check
if the NULLS marker found was the expected one. If not, the search
may not have examined all objects in the target bucket, so it is
repeated.
The unique NULLS_MARKER is derived from the address of the
head of the chain. As this cannot be derived at load-time the
static rhnull in rht_bucket_nested() needs to be initialised
at run time.
Any caller of a lookup function must still be prepared for the
possibility that the object returned is in a different table - it
might have been there for some time.
Note that this does NOT provide support for other uses of
NULLS_MARKERs such as allocating with SLAB_TYPESAFE_BY_RCU or changing
the key of an object and re-inserting it in the same table.
These could only be done safely if new objects were inserted
at the *start* of a hash chain, and that is not currently the case.
Signed-off-by: NeilBrown <neilb@suse.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2018 23:26:34 +0000 (15:26 -0800)]
Merge branch 'hns3-ethtool-dump'
Salil Mehta says:
====================
Adds VF/PF PCIe reg dump(ethtool -d) support to HNS3 driver
This patchset adds VF/PF PCIe register dump support to HNS3 VF and PF
driver using "ethtool -d" command.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 29 Nov 2018 16:40:59 +0000 (16:40 +0000)]
net: hns3: Adds support to dump(using ethool-d) PCIe regs in HNS3 PF driver
This patch adds support to dump PF PCIe registers using ethtool -d
for HNS3 PF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jian Shen [Thu, 29 Nov 2018 16:40:58 +0000 (16:40 +0000)]
net: hns3: Support "ethtool -d" for HNS3 VF driver
This patch adds "ethtool -d" support for HNS3 VF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Tue, 27 Nov 2018 21:30:14 +0000 (22:30 +0100)]
net: phy: improve generic EEE ethtool functions
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2018 22:16:14 +0000 (14:16 -0800)]
Merge branch 'VXLAN-underlay-VRF'
Alexis Bauvin says:
====================
net: Add VRF support for VXLAN underlay
v6 -> v7:
- proper locking for device in udp_tunnel following Sabrina Dubroca's advice
v5 -> v6:
- remove automatic rebinding patch following Roopa Prabhu's advice
v4 -> v5:
- move test script to its own patch (6/6)
- add schematic for test script
- apply David Ahern comments to the test script
v3 -> v4:
- rename vxlan_is_in_l3mdev_chain to netdev_is_upper master
- move it to net/core/dev.c
- make it return bool instead of int
- check if remote_ifindex is zero before resolving the l3mdev
- add testing script
v2 -> v3:
- fix build when CONFIG_NET_IPV6 is off
- fix build "unused l3mdev_master_upper_ifindex_by_index" build error with some
configs
v1 -> v2:
- move vxlan_get_l3mdev from vxlan driver to l3mdev driver as
l3mdev_master_upper_ifindex_by_index
- vxlan: rename variables named l3mdev_ifindex to ifindex
v0 -> v1:
- fix typos
We are trying to isolate the VXLAN traffic from different VMs with VRF as shown
in the schemas below:
+-------------------------+ +----------------------------+
| +----------+ | | +------------+ |
| | | | | | | |
| | tap-red | | | | tap-blue | |
| | | | | | | |
| +----+-----+ | | +-----+------+ |
| | | | | |
| | | | | |
| +----+---+ | | +----+----+ |
| | | | | | | |
| | br-red | | | | br-blue | |
| | | | | | | |
| +----+---+ | | +----+----+ |
| | | | | |
| | | | | |
| | | | | |
| +----+--------+ | | +--------------+ |
| | | | | | | |
| | vxlan-red | | | | vxlan-blue | |
| | | | | | | |
| +------+------+ | | +-------+------+ |
| | | | | |
| | VRF | | | VRF |
| | red | | | blue |
+-------------------------+ +----------------------------+
| |
| |
+---------------------------------------------------------+
| | | |
| | | |
| | +--------------+ | |
| | | | | |
| +---------+ eth0.2030 +---------+ |
| | 10.0.0.1/24 | |
| +-----+--------+ VRF |
| | green|
+---------------------------------------------------------+
|
|
+----+---+
| |
| eth0 |
| |
+--------+
iproute2 commands to reproduce the setup:
ip link add green type vrf table 1
ip link set green up
ip link add eth0.2030 link eth0 type vlan id 2030
ip link set eth0.2030 master green
ip addr add 10.0.0.1/24 dev eth0.2030
ip link set eth0.2030 up
ip link add blue type vrf table 2
ip link set blue up
ip link add br-blue type bridge
ip link set br-blue master blue
ip link set br-blue up
ip link add vxlan-blue type vxlan id 2 local 10.0.0.1 dev eth0.2030 \
port 4789
ip link set vxlan-blue master br-blue
ip link set vxlan-blue up
ip link set tap-blue master br-blue
ip link set tap-blue up
ip link add red type vrf table 3
ip link set red up
ip link add br-red type bridge
ip link set br-red master red
ip link set br-red up
ip link add vxlan-red type vxlan id 3 local 10.0.0.1 dev eth0.2030 \
port 4789
ip link set vxlan-red master br-red
ip link set vxlan-red up
ip link set tap-red master br-red
ip link set tap-red up
We faced some issue in the datapath, here are the details:
* Egress traffic:
The vxlan packets are sent directly to the default VRF because it's where the
socket is bound, therefore the traffic has a default route via eth0. the
workaround is to force this traffic to VRF green with ip rules.
* Ingress traffic:
When receiving the traffic on eth0.2030 the vxlan socket is unreachable from
VRF green. The workaround is to enable *udp_l3mdev_accept* sysctl, but
this breaks isolation between overlay and underlay: packets sent from
blue or red by e.g. a guest VM will be accepted by the socket, allowing
injection of VXLAN packets from the overlay.
This patch series fixes the issues describe above by allowing VXLAN socket to be
bound to a specific VRF device therefore looking up in the correct table.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexis Bauvin [Mon, 3 Dec 2018 09:54:41 +0000 (10:54 +0100)]
test/net: Add script for VXLAN underlay in a VRF
This script tests the support of a VXLAN underlay in a non-default VRF.
It does so by simulating two hypervisors and two VMs, an extended L2
between the VMs with the hypervisors as VTEPs with the underlay in a
VRF, and finally by pinging the two VMs.
It also tests that moving the underlay from a VRF to another works when
down/up the VXLAN interface.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexis Bauvin [Mon, 3 Dec 2018 09:54:40 +0000 (10:54 +0100)]
vxlan: add support for underlay in non-default VRF
Creating a VXLAN device with is underlay in the non-default VRF makes
egress route lookup fail or incorrect since it will resolve in the
default VRF, and ingress fail because the socket listens in the default
VRF.
This patch binds the underlying UDP tunnel socket to the l3mdev of the
lower device of the VXLAN device. This will listen in the proper VRF and
output traffic from said l3mdev, matching l3mdev routing rules and
looking up the correct routing table.
When the VXLAN device does not have a lower device, or the lower device
is in the default VRF, the socket will not be bound to any interface,
keeping the previous behaviour.
The underlay l3mdev is deduced from the VXLAN lower device
(IFLA_VXLAN_LINK).
+----------+ +---------+
| | | |
| vrf-blue | | vrf-red |
| | | |
+----+-----+ +----+----+
| |
| |
+----+-----+ +----+----+
| | | |
| br-blue | | br-red |
| | | |
+----+-----+ +---+-+---+
| | |
| +-----+ +-----+
| | |
+----+-----+ +------+----+ +----+----+
| | lower device | | | |
| eth0 | <- - - - - - - | vxlan-red | | tap-red | (... more taps)
| | | | | |
+----------+ +-----------+ +---------+
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexis Bauvin [Mon, 3 Dec 2018 09:54:39 +0000 (10:54 +0100)]
l3mdev: add function to retreive upper master
Existing functions to retreive the l3mdev of a device did not walk the
master chain to find the upper master. This patch adds a function to
find the l3mdev, even indirect through e.g. a bridge:
+----------+
| |
| vrf-blue |
| |
+----+-----+
|
|
+----+-----+
| |
| br-blue |
| |
+----+-----+
|
|
+----+-----+
| |
| eth0 |
| |
+----------+
This will properly resolve the l3mdev of eth0 to vrf-blue.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexis Bauvin [Mon, 3 Dec 2018 09:54:38 +0000 (10:54 +0100)]
udp_tunnel: add config option to bind to a device
UDP tunnel sockets are always opened unbound to a specific device. This
patch allow the socket to be bound on a custom device, which
incidentally makes UDP tunnels VRF-aware if binding to an l3mdev.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 3 Dec 2018 21:55:44 +0000 (13:55 -0800)]
Merge branch 'mlxsw-fw_load_policy'
Ido Schimmel says:
====================
mlxsw: Add 'fw_load_policy' devlink parameter
Shalom says:
Currently, drivers do not have the ability to control the firmware
loading policy and they always use their own fixed policy. This prevents
drivers from running the device with a different firmware version for
testing and/or debugging purposes. For example, testing a firmware bug
fix.
For these situations, the new devlink generic parameter,
'fw_load_policy', gives the ability to control this option and allows
drivers to run with a different firmware version than required by the
driver.
Patch #1 adds the new parameter to devlink. The other two patches, #2
and #3, add support for this parameter in the mlxsw driver.
Example:
# Query the devlink parameters supported by the device
$ devlink dev param show
pci/0000:03:00.0:
name fw_load_policy type generic
values:
cmode driverinit value driver
# Flash new firmware using ethtool
$ ethtool -f swp1 mellanox/mlxsw_spectrum-13.1703.4.mfa2
# Toggle parameter
$ devlink dev param set pci/0000:03:00.0 name fw_load_policy value flash cmode driverinit
# devlink reset
$ devlink dev reload pci/0000:03:00.0
# Query firmware version to show changes took affect
$ ethtool -i swp1
driver: mlxsw_spectrum
version: 1.0
firmware-version: 13.1703.4
expansion-rom-version:
bus-info: 0000:03:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
iproute2 patches available here:
https://github.com/tshalom/iproute2-next
v2:
* Change 'fw_version_check' to 'fw_load_policy' with values 'driver' and
'flash' (Jakub)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Mon, 3 Dec 2018 07:59:02 +0000 (07:59 +0000)]
mlxsw: spectrum: Load firmware version based on devlink parameter
Load firmware version based on 'fw_load_policy' devlink parameter. The
driver supports these two options:
* DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DRIVER (0)
Default, load firmware version preferred by the driver
* DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_FLASH (1)
Load firmware currently stored in flash
The second option, 'flash', allow the device to run with different firmware
version than preferred by the driver for testing and/or debugging purposes.
For example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Mon, 3 Dec 2018 07:59:01 +0000 (07:59 +0000)]
mlxsw: core: Reset firmware after flash during driver initialization
After flashing new firmware during the driver initialization flow (reload
or not), the driver should do a firmware reset when it gets -EAGAIN in
order to load the new one.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo [Mon, 3 Dec 2018 07:58:59 +0000 (07:58 +0000)]
devlink: Add 'fw_load_policy' generic parameter
Many drivers load the device's firmware image during the initialization
flow either from the flash or from the disk. Currently this option is not
controlled by the user and the driver decides from where to load the
firmware image.
'fw_load_policy' gives the ability to control this option which allows the
user to choose between different loading policies supported by the driver.
This parameter can be useful while testing and/or debugging the device. For
example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Heiner Kallweit [Mon, 3 Dec 2018 07:04:57 +0000 (08:04 +0100)]
net: phy: don't allow __set_phy_supported to add unsupported modes
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nathan Chancellor [Thu, 29 Nov 2018 06:01:05 +0000 (23:01 -0700)]
net: usb: aqc111: Initialize wol_cfg with memset in aqc111_suspend
Clang warns:
drivers/net/usb/aqc111.c:1326:37: warning: suggest braces around
initialization of subobject [-Wmissing-braces]
struct aqc111_wol_cfg wol_cfg = { 0 };
^
{}
1 warning generated.
Use memset to initialize the object to take compiler instrumentation out
of the equation.
Fixes:
e58ba4544c77 ("net: usb: aqc111: Add support for wake on LAN by MAGIC packet")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing [Thu, 29 Nov 2018 02:36:32 +0000 (02:36 +0000)]
net: qualcomm: rmnet: Remove set but not used variable 'cmd'
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c: In function 'rmnet_map_do_flow_control':
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:23:36: warning:
variable 'cmd' set but not used [-Wunused-but-set-variable]
struct rmnet_map_control_command *cmd;
'cmd' not used anymore now, should also be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nicolas Dichtel [Wed, 28 Nov 2018 18:12:56 +0000 (19:12 +0100)]
tun: implement carrier change
The userspace may need to control the carrier state.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paolo Abeni [Wed, 28 Nov 2018 16:37:53 +0000 (17:37 +0100)]
net: reorder flowi_common fields to avoid holes
the flowi* structures are used and memsetted by server functions
in critical path. Currently flowi_common has a couple of holes that
we can eliminate reordering the struct fields. As a side effect,
both flowi4 and flowi6 shrink by 8 bytes.
Before:
pahole -EC flowi_common
struct flowi_common {
// ...
/* size: 40, cachelines: 1, members: 10 */
/* sum members: 32, holes: 1, sum holes: 4 */
/* padding: 4 */
/* last cacheline: 40 bytes */
};
pahole -EC flowi6
struct flowi6 {
// ...
/* size: 88, cachelines: 2, members: 6 */
/* padding: 4 */
/* last cacheline: 24 bytes */
};
pahole -EC flowi4
struct flowi4 {
// ...
/* size: 56, cachelines: 1, members: 4 */
/* padding: 4 */
/* last cacheline: 56 bytes */
};
After:
struct flowi_common {
// ...
/* size: 32, cachelines: 1, members: 10 */
/* last cacheline: 32 bytes */
};
struct flowi6 {
// ...
/* size: 80, cachelines: 2, members: 6 */
/* padding: 4 */
/* last cacheline: 16 bytes */
};
struct flowi4 {
// ...
/* size: 48, cachelines: 1, members: 4 */
/* padding: 4 */
/* last cacheline: 48 bytes */
};
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Sat, 1 Dec 2018 01:06:29 +0000 (17:06 -0800)]
Merge branch 'mlxsw-Add-VxLAN-support-with-VLAN-aware-bridges'
Ido Schimmel says:
====================
mlxsw: Add VxLAN support with VLAN-aware bridges
Commit
53e50a6ec24d ("Merge branch 'mlxsw-Add-VxLAN-support'") added
mlxsw support for VxLAN when the VxLAN device was enslaved to
VLAN-unaware bridges. This patchset extends mlxsw to also support VxLAN
with VLAN-aware bridges.
With VLAN-aware bridges, the VxLAN device's VNI is mapped to the VLAN
that is configured as 'pvid untagged' on the corresponding bridge port.
To prevent ambiguity, mlxsw forbids configurations in which the same
VLAN is configured as 'pvid untagged' on multiple VxLAN devices.
Patches #1-#2 add the necessary APIs in mlxsw and the bridge driver.
Patches #3-#4 perform small refactoring in order to prepare mlxsw for
VLAN-aware support.
Patch #5 finally enables the enslavement of VxLAN devices to a
VLAN-aware bridge. Among other things, it extends mlxsw to handle
switchdev notifications about VLAN add / delete on a VxLAN device
enslaved to an offloaded VLAN-aware bridge.
Patches #6-#8 add selftests to test the new functionality.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:07:08 +0000 (20:07 +0000)]
selftests: forwarding: Add VxLAN test with a VLAN-aware bridge
The test is very similar to its VLAN-unaware counterpart
(vxlan_bridge_1d.sh), but instead of using multiple VLAN-unaware
bridges, a single VLAN-aware bridge is used with multiple VLANs.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:07:06 +0000 (20:07 +0000)]
selftests: mlxsw: Add a test for VxLAN configuration with a VLAN-aware bridge
Extend the existing VLAN-unaware tests with their VLAN-aware
counterparts. This includes sanitization of invalid configuration and
offload indication on the local route performing decapsulation and the
FDB entries perform encapsulation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:07:05 +0000 (20:07 +0000)]
selftests: mlxsw: Consider VLAN-aware bridges as valid
Previous patches add the ability to work with VLAN-aware bridges and
VxLAN devices, so make sure such configuration no longer fails.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:07:04 +0000 (20:07 +0000)]
mlxsw: spectrum: Enable VxLAN enslavement to VLAN-aware bridges
Commit
1c30d1836aeb ("mlxsw: spectrum: Enable VxLAN enslavement to
bridges") enabled the enslavement of VxLAN devices to bridges that have
mlxsw ports (or their upper) as slaves. This patch extends mlxsw to also
support VLAN-aware bridges.
The patch is similar in nature to mentioned commit, but there is one
major difference. With VLAN-aware bridges, the VxLAN device's VNI is
mapped to the VLAN that is configured as PVID and egress untagged on the
bridge port.
Therefore, the driver is extended to listen to VLAN configuration on
VxLAN devices of interest and enable / disable NVE encapsulation on the
corresponding 802.1Q FIDs.
To prevent ambiguity, the driver makes sure that a given VLAN is not
configured as PVID and egress untagged on multiple VxLAN devices. This
sanitization takes place both when a port is enslaved to a bridge with
existing VxLAN devices and when a VLAN is added to / removed from a
VxLAN device of interest.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:07:02 +0000 (20:07 +0000)]
mlxsw: spectrum_switchdev: Prepare function for VLAN-aware bridges
The vxlan_join() function resolves the FID on which the VNI should be
set and then sets the VNI. Currently, the FID is simply resolved
according to the ifindex of the bridge device to which the VxLAN device
is enslaved. This works because only VLAN-unaware bridges are supported.
With VLAN-aware bridges the FID would need to be resolved based on the
VLAN to which the VNI is mapped to.
Add the VLAN ID to the argument list of the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:07:01 +0000 (20:07 +0000)]
mlxsw: spectrum_switchdev: Unify VxLAN leave function
The function mlxsw_sp_bridge_vxlan_leave() is currently split between
VLAN-aware and VLAN-unaware bridges, but actually both types can use the
same function.
The function needs to resolve the FID that corresponds to the VxLAN
device and disable NVE encapsulation on it. Instead of looking up the
FID differently for VLAN-aware and VLAN-unaware bridges, we can always
use the VxLAN's device VNI.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:06:59 +0000 (20:06 +0000)]
mlxsw: spectrum_fid: Add API to lookup 802.1Q FIDs without creating them
In a similar fashion to commit
564c6d727aca ("mlxsw: spectrum_fid: Add
APIs to lookup FID without creating it"), add a corresponding API to
lookup 802.1Q FIDs.
This is a prerequisite to VxLAN support with VLAN-aware bridges and will
allow us to resolve a 802.1Q FID by its VLAN when an FDB entry is added
on the bridge port of the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido Schimmel [Wed, 28 Nov 2018 20:06:58 +0000 (20:06 +0000)]
net: bridge: Extend br_vlan_get_pvid() for bridge ports
Currently, the function only works for the bridge device itself, but
subsequent patches will need to be able to query the PVID of a given
bridge port, so extend the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Nov 2018 21:45:13 +0000 (13:45 -0800)]
Merge branch 'qed-Doorbell-overflow-recovery'
Ariel Elior says:
====================
qed*: Doorbell overflow recovery
Doorbell Overflow
If sufficient CPU cores will send doorbells at a sufficiently high rate, they
can cause an overflow in the doorbell queue block message fifo. When fill level
reaches maximum, the device stops accepting all doorbells from that PF until a
recovery procedure has taken place.
Doorbell Overflow Recovery
The recovery procedure basically means resending the last doorbell for every
doorbelling entity. A doorbelling entity is anything which may send doorbells:
L2 tx ring, rdma sq/rq/cq, light l2, vf l2 tx ring, spq, etc. This relies on
the design assumption that all doorbells are aggregative, so last doorbell
carries the information of all previous doorbells.
APIs
All doorbelling entities need to register with the mechanism before sending
doorbells. The registration entails providing the doorbell address the entity
would be using, and a virtual address where last doorbell data can be found.
Typically fastpath structures already have this construct.
Executing the recovery procedure
Handling the attentions, iterating over all the registered entities and
resending their doorbells, is all handled within qed core module.
Relevance
All doorbelling entities in all protocols need to register with the mechanism,
via the new APIs. Technically this is quite simple (just call the API). Some
protocol fastpath implementation may not have the doorbell data stored anywhere
(compute it from scratch every time) and will have to add such a place.
This is rare and is also better practice (save some cycles on the fastpath).
Performance Penalty
No performance penalty should incur as a result of this feature. If anything
performance can improve by avoiding recalcualtion of doorbell data everytime
doorbell is sent (in some flows).
Add the database used to register doorbelling entities, and APIs for adding
and deleting entries, and logic for traversing the database and doorbelling
once on behalf of all entities.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Wed, 28 Nov 2018 16:16:07 +0000 (18:16 +0200)]
qede: Register l2 queues with doorbell overflow recovery mechanism
All L2 queues funnel through this flow, so this would cover the
regular RSS queues, as well queues created for VFs, mqos queues,
xdp queues, etc.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Wed, 28 Nov 2018 16:16:06 +0000 (18:16 +0200)]
qed: Expose the doorbell overflow recovery mechanism to the protocol drivers
Most of the doorbelling entities are outside of the core module.
L2 queues, Roce queues, iscsi and fcoe all need to register.
Make the APIs available for these drivers.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Wed, 28 Nov 2018 16:16:05 +0000 (18:16 +0200)]
qed: Register light L2 queues with doorbell overflow recovery mechanism
Light L2 queues are doorbelling entities. Modify the implementation
to keep the doorbell data necessary for doorbelling in well known
location instead of recomputing every time. Register the LL2 queue
with doorbell recovery mechanism.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Wed, 28 Nov 2018 16:16:04 +0000 (18:16 +0200)]
qed: Register slowpath queue doorbell with doorbell overflow recovery mechanism
Slow path queue is a doorbelling entity. Register it with the overflow mechanism.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Wed, 28 Nov 2018 16:16:03 +0000 (18:16 +0200)]
qed: Use the doorbell overflow recovery mechanism in case of doorbell overflow
In case of an attention from the doorbell queue block, analyze the HW
indications. In case of a doorbell overflow, execute a doorbell recovery.
Since there can be spurious indications (race conditions between multiple PFs),
schedule a periodic task for checking whether a doorbell overflow may have been
missed. After a set time with no indications, terminate the periodic task.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ariel Elior [Wed, 28 Nov 2018 16:16:02 +0000 (18:16 +0200)]
qed: Add doorbell overflow recovery mechanism
Add the database used to register doorbelling entities, and APIs for adding
and deleting entries, and logic for traversing the database and doorbelling
once on behalf of all entities.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Nov 2018 21:33:35 +0000 (13:33 -0800)]
Merge branch 'rtnetlink-avoid-a-warning-in-rtnl_newlink'
Jakub Kicinski says:
====================
rtnetlink: avoid a warning in rtnl_newlink()
I've been hoping for some time that someone more competent would fix
the stack frame size warning in rtnl_newlink(), but looks like I'll
have to take a stab at it myself :) That's the only warning I see
in most of my builds.
First patch refactors away a somewhat surprising if (1) code block.
Reindentation will most likely cause cherry-pick problems but OTOH
rtnl_newlink() doesn't seem to be changed often, so perhaps we can
risk it in the name of cleaner code?
Second patch fixes the warning in simplest possible way. I was
pondering if there is any more clever solution, but I can't see it..
rtnl_newlink() is quite long with a lot of possible execution paths
so doing memory allocations half way through leads to very ugly
results.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:32:31 +0000 (22:32 -0800)]
rtnetlink: avoid frame size warning in rtnl_newlink()
Standard kernel compilation produces the following warning:
net/core/rtnetlink.c: In function ‘rtnl_newlink’:
net/core/rtnetlink.c:3232:1: warning: the frame size of 1288 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
This should not really be an issue, as rtnl_newlink() stack is
generally quite shallow.
Fix the warning by allocating attributes with kmalloc() in a wrapper
and passing it down to rtnl_newlink(), avoiding complexities on error
paths.
Alternatively we could kmalloc() some structure within rtnl_newlink(),
slave attributes look like a good candidate. In practice it adds to
already rather high complexity and length of the function.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:32:30 +0000 (22:32 -0800)]
rtnetlink: remove a level of indentation in rtnl_newlink()
rtnl_newlink() used to create VLAs based on link kind. Since
commit
ccf8dbcd062a ("rtnetlink: Remove VLA usage") statically
sized array is created on the stack, so there is no more use
for a separate code block that used to be the VLA's live range.
While at it christmas tree the variables. Note that there is
a goto-based retry so to be on the safe side the variables can
no longer be initialized in place. It doesn't seem to matter,
logically, but why make the code harder to read..
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Fri, 30 Nov 2018 21:30:45 +0000 (13:30 -0800)]
Merge branch 'nfp-update-TX-path-to-enable-repr-offloads'
Jakub Kicinski says:
====================
nfp: update TX path to enable repr offloads
This set starts with three micro optimizations to the TX path.
The improvement is measurable, but below 1% of CPU utilization.
Patches 4 - 9 add basic TX offloads to representor devices, like
checksum offload or TSO, and remove the unnecessary TX lock and
Qdisc (our representors are software constructs on top of the PF).
The last 2 patches add more info to error messages - id of command
which failed and exact location of incorrect TLVs, very useful for
debugging.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:24:58 +0000 (22:24 -0800)]
nfp: report more info when reconfiguration fails
FW reconfiguration timeouts are a common indicator of FW trouble.
To make debugging easier print requested update and control word
when reconfiguration fails.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:24:57 +0000 (22:24 -0800)]
nfp: add offset to all TLV parsing errors
When troubleshooting incorrect FW capabilities it's useful to know
where the faulty TLV is located. Add offset to all errors messages.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:24:56 +0000 (22:24 -0800)]
nfp: add offloads on representors
FW/HW can generally support the standard networking offloads
on representors without any trouble. Add the ability for FW
to advertise which features should be available on representors.
Because representors are muxed on top of the vNIC we need to listen
on feature changes of their lower devices, and update their features
appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:24:55 +0000 (22:24 -0800)]
nfp: add locking around representor changes
Up until now we never needed to keep a networking locks around
representors accesses, we only accessed them when device was
reconfigured (under nfp pf->lock) or on fast path (under RCU).
Now we want to be able to iterate over all representors during
notifications, so make sure representor assignment is done
under RTNL lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:24:54 +0000 (22:24 -0800)]
nfp: run don't require Qdiscs on representor netdevs
Our representors are software devices built on top of the PF
vNIC, the queuing should only happen at the vNIC netdevice.
Allow representors to run qdisc-less.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski [Wed, 28 Nov 2018 06:24:53 +0000 (22:24 -0800)]
nfp: run representor TX locklessly
Our representors are software devices built on top of the PF
vNIC, the only state they have are per-cpu stats, so make
the TX run locklessly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>