Thomas Bogendoerfer [Mon, 18 Feb 2008 21:38:32 +0000 (22:38 +0100)]
[MIPS] IP28: Add defconfig file
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thiemo Seufer [Thu, 14 Feb 2008 16:58:25 +0000 (16:58 +0000)]
[MIPS] SB1: Fix CONFIG_SIBYTE_DMA_PAGEOPS build failure.
Fix type mismatch warnings for 64-bit kernel builds which trigger -Werror.
The problem affects only SB-1 kernels with CONFIG_SIBYTE_DMA_PAGEOPS
enabled.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Mon, 18 Feb 2008 18:49:48 +0000 (18:49 +0000)]
[MIPS] BCM1480: Remove stray function call resulting in infinite recursion
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Sat, 16 Feb 2008 22:34:25 +0000 (22:34 +0000)]
[MIPS] Fix buggy invocations of kmap_coherent()
kmap_coherent will only work correctly if the page it is called on is
not marked dirty. If it's dirty the kernel address of the page should
be used instead of a temporary mapping.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Thomas Koeller [Mon, 11 Feb 2008 22:42:12 +0000 (23:42 +0100)]
[MIPS] Fix broken rm7000/rm9000 interrupt handling
Properly acknowledge RM7K and RM9K interrupts. Before this, interrupts were
permanently masked after their first occurrence, making them non-functional.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Mon, 11 Feb 2008 14:51:40 +0000 (14:51 +0000)]
[MIPS] Handle I-cache coherency in flush_cache_range()
So far flush_cache_range() did't consider the I-cache largely because it
did rarely ever matter to real world code. This was working primarily
because normally code and data are don't share the same pages - with the
exception of MIPS16 code which uses address constants embedded between
the code. The following sequence of events may break the code:
o MIPS16 executable being loaded
o dynamic linker relocates the address constants embedded into the code:
o Uses mprotect(2) to make code pages PROT_READ|PROT_WRITE
o Performs the actual relocations by writing to the pages which likely
are COW. Because no PROT_EXEC is set I-cache coherence will not be
considered.
o Uses mprotect(2) to switch code pages back to PROT_READ|PROT_EXEC.
This results in a call to flush_cache_range() which also does not
consider I-caches.
o => executing the page just having been relocated may now result in the
I-cache getting refilled with stale data from memory.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ralf Baechle [Fri, 8 Feb 2008 13:13:27 +0000 (13:13 +0000)]
[MIPS] IP27: Add missing ~ in DMA code.
Harmless since this function is not being called on I/O coherent systems
such as IP27.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pavel Emelyanov [Tue, 5 Feb 2008 07:44:24 +0000 (23:44 -0800)]
[MIPS] Use find_task_by_vpid in system calls
There are some places left in mips, that lookup task in initial namespace,
while the code doing so gets the pid from the user space and thus must
treat it as virtual.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Linus Torvalds [Tue, 19 Feb 2008 02:46:56 +0000 (18:46 -0800)]
Merge git://git./linux/kernel/git/bart/ide-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide-cd: fix missing residual count setting in DMA mode
ht6560b: force prefetch for some devices
ht6560b can only do up to PIO mode 4
linux/hdsmart.h: fix goofups (take 2)
via82cxxx: add new PCI id for cx700
falconide: locking bugfix
MAINTAINERS: update ide-cd maintainer's email address
ide/libata: ST310211A has buggy HPA too
ide: Add missing base addresses for falconide and macide
Eric Paris [Mon, 18 Feb 2008 23:23:16 +0000 (18:23 -0500)]
Audit: use == not = in if statements
Clearly this was supposed to be an == not an = in the if statement.
This patch also causes us to stop processing execve args once we have
failed rather than continuing to loop on failure over and over and over.
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kiyoshi Ueda [Tue, 19 Feb 2008 00:41:26 +0000 (01:41 +0100)]
ide-cd: fix missing residual count setting in DMA mode
This patch fixes the missing residual count setting in DMA mode,
which was introduced during the conversion to blk-end-request.
The residual count could be used by the request submitter.
So if it isn't set correctly, some upper layers does not work.
(e.g. wodim for CD burning.)
The bug is in only DMA mode.
In PIO mode, we are setting the residual count correctly,
so no need to fix.
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Reported-by: Andreas Schwab <schwab@suse.de>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: Laura Garcia <nevola@gmail.com>
Tested-by: Borislav Petkov <petkovbb@googlemail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jan Evert van Grootheest [Tue, 19 Feb 2008 00:41:26 +0000 (01:41 +0100)]
ht6560b: force prefetch for some devices
Prefetch needs to be set for some ide devices to work when connected to
a ht6560b interface. This was not always done properly, causing a system
with a HD and CD on the primary interface to not work properly. Or, in
effect, hang hard.
This patch forces prefetch on devices before checking whether it
is necessary to change the settings in the interface
This patch should also be applied to 2.4. I don't currently have a
2.4 tree around.
(also change my email address)
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Jan Evert van Grootheest [Tue, 19 Feb 2008 00:41:26 +0000 (01:41 +0100)]
ht6560b can only do up to PIO mode 4
According to the datasheet, ht6560b only supports up to PIO mode 4.
[bart: manually ported it over 2.6.25-rc2]
Signed-off-by: Jan Evert van Grootheest <janevert@caiway.nl>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 19 Feb 2008 00:41:26 +0000 (01:41 +0100)]
linux/hdsmart.h: fix goofups (take 2)
Fix goofups of commit
76166952bbc81dda1c8a8c14e75a2aa06f6c052c
("<linux/hdsmart.h> is not used by kernel code").
Also update include/linux/Kbuild to reflect the fact that hdsmart.h
uses __KERNEL__ ifdefs now.
Reported-by: "Robert P. J. Day" <rpjday@crashcourse.ca>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Andrew Smith [Tue, 19 Feb 2008 00:41:26 +0000 (01:41 +0100)]
via82cxxx: add new PCI id for cx700
[bart: manually ported it over via82cxxx changes]
From: Andrew Smith <asmith@tranquility.fsbusiness.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Bartlomiej Zolnierkiewicz [Tue, 19 Feb 2008 00:41:25 +0000 (01:41 +0100)]
falconide: locking bugfix
commit
8ac4ce742c66100931b6f2d7a36b0df08bc721fe ("ide: fix host drivers
depending on ide_generic to probe for interfaces (take 2)") moved probing
to falconide but forgot to take care of Atari specific locking - fix it.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Borislav Petkov [Tue, 19 Feb 2008 00:41:25 +0000 (01:41 +0100)]
MAINTAINERS: update ide-cd maintainer's email address
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mikko Rapeli [Tue, 19 Feb 2008 00:41:25 +0000 (01:41 +0100)]
ide/libata: ST310211A has buggy HPA too
Signed-off-by: Mikko Rapeli <mikko.rapeli@teleca.com>
Tested-by: Bart Champagne <bart@as35701.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Geert Uytterhoeven [Tue, 19 Feb 2008 00:41:24 +0000 (01:41 +0100)]
ide: Add missing base addresses for falconide and macide
commit
29dd59755a849cc6475faa6a75f3b804e23a6fc2 ("ide: remove ide_setup_ports")
forgot to take into account the base addresses for the CONTROL registers for
falconide and macide, as pointed out by Michael Schmitz.
Falconide was tested on Aranym.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michael Schmitz <schmitz@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Linus Torvalds [Mon, 18 Feb 2008 23:52:40 +0000 (15:52 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Fix possible array overrun
RDMA/nes: Fix VLAN support
RDMA/nes: Fix MAC interrupt erroneously masked on ifdown
IB: Fix return value in ib_device_register_sysfs()
Linus Torvalds [Mon, 18 Feb 2008 23:51:40 +0000 (15:51 -0800)]
Merge git://git./linux/kernel/git/x86/linux-2.6-x86
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: fix lguest build failure
x86: reenable support for system without on node0
x86: CPA: avoid double checking of alias ranges
x86: CPA no alias checking for _NX
x86: zap invalid and unused pmds in early boot
x86: CPA, fix alias checks
Linus Torvalds [Mon, 18 Feb 2008 23:49:47 +0000 (15:49 -0800)]
Merge git://git./linux/kernel/git/mchehab/v4l-dvb
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (59 commits)
V4L/DVB (7219): zoran: Fix namespace conflicts with Zoran 'GPIO_MAX' enum
V4L/DVB (7205): tuner-xc2028 depends on FW_LOADER
V4L/DVB (7201): cx88-mpeg: Fix race condition in variable access
V4L/DVB (7200): Fix FM firmware loading
V4L/DVB (7198): V4L, include ioctl.h in videodev headers
V4L/DVB (7197): bttv: Fix overlay divide error
V4L/DVB (7195): xc5000: fix build error when built as module
V4L/DVB (7194): cx88-mpeg: Allow concurrent access to cx88-mpeg devices
V4L/DVB (7193): tveeprom: Add proper tuner mapping for hauppauge eeprom id 133
V4L/DVB (7192): Adds support for Genius TVGo A11MCE
V4L/DVB (7189): autosuspend support
V4L/DVB (7188): radio-si470x version 1.0.6
V4L/DVB (7186): tda10086: make the 22kHz tone for DISEQC a config option
V4L/DVB (7183): radio-si470x: fix build warning
V4L/DVB (7180): em28xx: add URB_NO_TRANSFER_DMA_MAP, since urb->transfer_dma is set
V4L/DVB (7179): Allow more than one em28xx board
V4L/DVB (7164): em28xx-alsa: Add a missing mutex
V4L/DVB (7163): em28xx: makes audio settings more stable
V4L/DVB (7162): em28xx: Fix endian and returns the correct values
V4L/DVB (7161): em28xx: Fix printing debug values higher than 127
...
Linus Torvalds [Mon, 18 Feb 2008 23:46:21 +0000 (15:46 -0800)]
Merge branch 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6
* 'for-linus' of git://oss.sgi.com:8090/xfs/xfs-2.6:
[XFS] Added quota targets and removed dmapi directory
[XFS] Fix up xfs out-of-tree builds. (a.k.a. external modules)
[XFS] Remove Makefile wrappers in XFS
Linus Torvalds [Mon, 18 Feb 2008 23:46:03 +0000 (15:46 -0800)]
Merge git://git./linux/kernel/git/herbert/crypto-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
[CRYPTO] null: Add missing Kconfig dependency on BLKCIPHER
[CRYPTO] tcrypt: Add missing Kconfig dependency on BLKCIPHER
[HIFN]: Fix invalid config ifdefs for RNG support
Linus Torvalds [Mon, 18 Feb 2008 23:45:48 +0000 (15:45 -0800)]
Merge git://git./linux/kernel/git/tglx/linux-2.6-hrt
* git://git.kernel.org/pub/scm/linux/kernel/git/tglx/linux-2.6-hrt:
timer_list: print relative expiry time signed
Linus Torvalds [Mon, 18 Feb 2008 23:41:05 +0000 (15:41 -0800)]
Merge git://git./linux/kernel/git/sam/kbuild
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
kbuild: explain why DEBUG_SECTION_MISMATCH is UNDEFINED
kbuild: fix building vmlinux.o
kbuild: allow -fstack-protector to take effect
kconfig: fix select in combination with default
Rusty Russell [Sun, 3 Feb 2008 20:11:10 +0000 (07:11 +1100)]
x86: fix lguest build failure
drivers/lguest/x86/switcher_32.S:(.text+0x3815f8):
undefined reference to `LGUEST_PAGES_regs_trapnum'
This problem was caused by asm-offsets.c only having the offsets when
lguest *guest* support was set, not lguest host (host support used to
imply guest support, so now they're separate these bugs come out).
Lguest guest support and host support are separate config options:
they used to be tied together. Sort out which parts of asm-offsets are
needed for Guest and Host.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Yinghai Lu [Sun, 17 Feb 2008 10:02:21 +0000 (02:02 -0800)]
x86: reenable support for system without on node0
One system doesn't have RAM for node0 installed.
SRAT: PXM 0 -> APIC 0 -> Node 0
SRAT: PXM 0 -> APIC 1 -> Node 0
SRAT: PXM 1 -> APIC 2 -> Node 1
SRAT: PXM 1 -> APIC 3 -> Node 1
SRAT: Node 1 PXM 1 0-a0000
SRAT: Node 1 PXM 1 0-
dd000000
SRAT: Node 1 PXM 1 0-
123000000
ACPI: SLIT: nodes = 2
10 13
13 10
mapped APIC to
ffffffffff5fb000 (
fee00000)
Bootmem setup node 1
0000000000000000-
0000000123000000
NODE_DATA [
000000000000e000 -
0000000000014fff]
bootmap [
0000000000015000 -
00000000000395ff] pages 25
Could not find start_pfn for node 0
Pid: 0, comm: swapper Not tainted 2.6.24-smp-g5a514e21-dirty #14
Call Trace:
[<
ffffffff80bab498>] free_area_init_node+0x22/0x381
[<
ffffffff8045ffc5>] generic_swap+0x0/0x17
[<
ffffffff80bab0cc>] find_zone_movable_pfns_for_nodes+0x54/0x271
[<
ffffffff80baba5f>] free_area_init_nodes+0x239/0x287
[<
ffffffff80ba6311>] paging_init+0x46/0x4c
[<
ffffffff80b9dda5>] setup_arch+0x3c3/0x44e
[<
ffffffff80b978be>] start_kernel+0x6f/0x2c7
[<
ffffffff80b971cc>] _sinittext+0x1cc/0x1d3
This happens because node 0 is not online, but the node state in
mm/page_alloc.c has node 0 set.
nodemask_t node_states[NR_NODE_STATES] __read_mostly = {
[N_POSSIBLE] = NODE_MASK_ALL,
[N_ONLINE] = { { [0] = 1UL } },
So we need to clear node_online_map before initializing the memory.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas Gleixner [Fri, 15 Feb 2008 21:17:57 +0000 (22:17 +0100)]
x86: CPA: avoid double checking of alias ranges
When the CPA code is called with an virtual address in the range of
the direct mapping or the high alias then we do not need to run
through the alias check for this range.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Fri, 15 Feb 2008 20:49:46 +0000 (21:49 +0100)]
x86: CPA no alias checking for _NX
NX settings are not required to be consistent across alias mappings.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Fri, 15 Feb 2008 16:29:12 +0000 (17:29 +0100)]
x86: zap invalid and unused pmds in early boot
The early boot code maps KERNEL_TEXT_SIZE (currently 40MB) starting
from __START_KERNEL_map. The kernel itself only needs _text to _end
mapped in the high alias. On relocatible kernels the ASM setup code
adjusts the compile time created high mappings to the relocation. This
creates invalid pmd entries for negative offsets:
0xffffffff80000000 -> pmd entry:
ffffffffff2001e3
It points outside of the physical address space and is marked present.
This starts at the virtual address __START_KERNEL_map and goes up to
the point where the first valid physical address (0x0) is mapped.
Zap the mappings before _text and after _end right away in early
boot. This removes also the invalid entries.
Furthermore it simplifies the range check for high aliases.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Gleixner [Mon, 18 Feb 2008 19:54:14 +0000 (20:54 +0100)]
x86: CPA, fix alias checks
c_p_a() did not discover all aliases correctly. (such as when called
on vmalloc()-ed areas or ioremap()-ed areas)
Push the alias checks to the lower, physical level and consistently
discover all aliases that might exist: the low direct mappings and
the high linear kernel-text mappings (on 64-bit).
Thanks to Andi Kleen for pointing out that this was buggy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Roland Dreier [Mon, 18 Feb 2008 18:33:59 +0000 (10:33 -0800)]
RDMA/nes: Fix possible array overrun
In nes_create_qp(), the test
if (nesqp->mmap_sq_db_index > NES_MAX_USER_WQ_REGIONS) {
is used to error out if the db_index is too large; however, if the
test doesn't trigger, then the index is used as
nes_ucontext->mmap_nesqp[nesqp->mmap_sq_db_index] = nesqp;
and mmap_nesqp is declared as
struct nes_qp *mmap_nesqp[NES_MAX_USER_WQ_REGIONS];
which leads to an array overrun if the index is exactly equal to
NES_MAX_USER_WQ_REGIONS. Fix this by bailing out if the index is
greater than or equal to NES_MAX_USER_WQ_REGIONS.
This was spotted by the Coverity checker (CID 2162).
Acked-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Mauro Carvalho Chehab [Fri, 15 Feb 2008 21:41:06 +0000 (18:41 -0300)]
V4L/DVB (7219): zoran: Fix namespace conflicts with Zoran 'GPIO_MAX' enum
Thanks to Martin Michlmayr <tbm@cyrius.com> for reporting this issue:
The zoran driver fails to compile on the ARM Orion platform with:
In file included from drivers/media/video/zoran_procfs.c:50:
drivers/media/video/zoran.h:232: error: expected identifier before numeric
constant
The reason is that drivers/media/video/zoran.h defines an enum with
GPIO_MAX in it, but Orion contains a #define GPIO_MAX 32 in
include/asm-arm/arch-orion/orion.h
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Paul Mundt [Thu, 14 Feb 2008 10:24:22 +0000 (07:24 -0300)]
V4L/DVB (7205): tuner-xc2028 depends on FW_LOADER
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ricardo Cerqueira [Thu, 14 Feb 2008 01:41:15 +0000 (22:41 -0300)]
V4L/DVB (7201): cx88-mpeg: Fix race condition in variable access
There was a possible race condition in the increment/decrement of
the active device references counter.
Thanks to Trent Piepho (xyzzy@speakeasy.org) for bringing it up.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 14 Feb 2008 04:52:48 +0000 (01:52 -0300)]
V4L/DVB (7200): Fix FM firmware loading
There's no need to load SCode table for FM.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jiri Slaby [Wed, 13 Feb 2008 23:04:49 +0000 (20:04 -0300)]
V4L/DVB (7198): V4L, include ioctl.h in videodev headers
Fix compilation of user processes which includes videodev*.h but
not includes linux/ioctl.h:
v4l2ext_helper.c: In function 'process_ioctl':
v4l2ext_helper.c:183: warning: implicit declaration of function '_IOWR'
v4l2ext_helper.c:183: error: expected expression before 'struct'
v4l2ext_helper.c:183: error: case label does not reduce to an integer constant
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Robert Fitzsimons [Wed, 13 Feb 2008 19:38:11 +0000 (16:38 -0300)]
V4L/DVB (7197): bttv: Fix overlay divide error
The initial work to convert the bttv driver to V4L2 "Partial conversion
from V4L1 to V4L2" (
e84619b17440ccca4e4db7583d126c4189b987e5), missed
the line which set the appropriate overlay crop structure in the newly
allocated bttv_buffer. This then causes a divide error in the
bttv_calc_geo function.
Signed-off-by: Robert Fitzsimons <robfitz@273k.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tony Breeds [Tue, 12 Feb 2008 05:54:33 +0000 (02:54 -0300)]
V4L/DVB (7195): xc5000: fix build error when built as module
drivers/built-in.o: In function `set_type':
tuner-core.c:(.text+0x8879d): undefined reference to `xc5000_attach'
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Roland Stoll [Mon, 11 Feb 2008 16:00:34 +0000 (13:00 -0300)]
V4L/DVB (7194): cx88-mpeg: Allow concurrent access to cx88-mpeg devices
It currently isn't possible to open the frontend device of cx88-mpeg devices
(DVB or Blackbird) multiple times concurrently. (for instance, to attach a
signal monitoring tool while reading a stream, or to send a frequency change
ioctl) This patch fixes that condition.
Signed-off-by: Roland Stoll <roland@xindex.de>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ricardo Cerqueira [Wed, 16 Jan 2008 22:56:55 +0000 (19:56 -0300)]
V4L/DVB (7193): tveeprom: Add proper tuner mapping for hauppauge eeprom id 133
Do away with the need to set tuner=63 on cx88xx with recent HVR-1300 boards
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Pardini [Mon, 11 Feb 2008 15:40:53 +0000 (12:40 -0300)]
V4L/DVB (7192): Adds support for Genius TVGo A11MCE
Signed-off-by: Adrian Pardini <pardo.bsso@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tobias Lorenz [Sat, 9 Feb 2008 19:08:24 +0000 (16:08 -0300)]
V4L/DVB (7189): autosuspend support
Together with Oliver Neukum from Novell, USB autosuspend support was added.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tobias Lorenz [Tue, 5 Feb 2008 01:26:08 +0000 (22:26 -0300)]
V4L/DVB (7188): radio-si470x version 1.0.6
This patch combines all the finished discussions and its resulting patches from
the mailing list.
The version 1.0.6 is mainly influenced by Oliver Neukum. He found a lot of
small issues, that are fixed with this patch now. For me the most interesting
thing is, that it's now safer to use it on other architectures.
The history for version 1.0.6 is:
- fixed coverity checker warnings in *_usb_driver_disconnect
- probe()/open() race by correct ordering in probe()
- DMA coherency rules by separate allocation of all buffers
- use of endianness macros
- abuse of spinlock, replaced by mutex
- racy handling of timer in disconnect, replaced by delayed_work
- racy interruptible_sleep_on(), replaced with wait_event_interruptible()
- handle signals in read()
The driver is tested with all Debian/testing radio programs and rdsd. The patch
is tested against checkpatch.pl v1.12.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hartmut Hackmann [Sun, 10 Feb 2008 02:54:24 +0000 (23:54 -0300)]
V4L/DVB (7186): tda10086: make the 22kHz tone for DISEQC a config option
Some cards need the diseqc signal modulated, while some just need
the envelope to control the LNB supply.
This fixes Bug 9887
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Michael Krufky [Sun, 10 Feb 2008 23:13:25 +0000 (20:13 -0300)]
V4L/DVB (7183): radio-si470x: fix build warning
fix the following build warning:
radio-si470x.c: In function 'si470x_get_rds_registers':
radio-si470x.c:562: warning: format '%ld' expects type 'long int',
but argument 3 has type 'unsigned int'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Fri, 8 Feb 2008 19:07:04 +0000 (16:07 -0300)]
V4L/DVB (7180): em28xx: add URB_NO_TRANSFER_DMA_MAP, since urb->transfer_dma is set
Thanks to Alan Stern <stern@rowland.harvard.edu> for pointing this issue.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Fri, 8 Feb 2008 18:44:25 +0000 (15:44 -0300)]
V4L/DVB (7179): Allow more than one em28xx board
em28xx driver is capable of handling more than one usb device. However, isoc
transfers require a large amount of data to be transfered.
Before this patch, just one em28xx board were enough to allocate more than 50%
URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=480/800 us (60%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, only one board could use an USB host at the same time. After the patch, it
is possible to use more than one em28xx at the same time, on the same usb host,
if the image size is slower or equal to 345600, since those images will
require about 30% of the URBs:
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc=232/800 us (29%), #Int= 0, #Iso= 2
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
So, in thesis, after the patch, it would be possible to use up to 3 boards by
each usb host, if the devices are generating small images.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Wed, 6 Feb 2008 21:52:15 +0000 (18:52 -0300)]
V4L/DVB (7164): em28xx-alsa: Add a missing mutex
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Wed, 6 Feb 2008 21:34:13 +0000 (18:34 -0300)]
V4L/DVB (7163): em28xx: makes audio settings more stable
Improves audio configurations on em28xx:
- mutes audio before changing amux;
- adds a delay after setting audio src;
- waits up to 50ms for ac97 busy.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Wed, 6 Feb 2008 18:56:16 +0000 (15:56 -0300)]
V4L/DVB (7162): em28xx: Fix endian and returns the correct values
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Wed, 6 Feb 2008 18:55:19 +0000 (15:55 -0300)]
V4L/DVB (7161): em28xx: Fix printing debug values higher than 127
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Wed, 6 Feb 2008 12:00:41 +0000 (09:00 -0300)]
V4L/DVB (7160): em28xx: Allow register dump/setting for debug
Adds vidioc_[g|s]_register handlers. This allows getting/setting register
from em28xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Wed, 6 Feb 2008 01:29:26 +0000 (22:29 -0300)]
V4L/DVB (7158): Fix em28xx audio initialization
AC97 register initialization seem to always be needed. This patch fixes audio
for Prolink/Pixelview USB2 board.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Andrew Morton [Tue, 5 Feb 2008 10:37:21 +0000 (07:37 -0300)]
V4L/DVB (7156): em28xx/em28xx-core.c: fix use of potentially uninitialized variable
drivers/media/video/em28xx/em28xx-core.c: In function 'em28xx_set_audio_source':
drivers/media/video/em28xx/em28xx-core.c:276: warning: 'no_ac97' may be used uninitialized in this function
This looks like a genuine bug to me.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Brandon Philips [Mon, 4 Feb 2008 23:52:21 +0000 (20:52 -0300)]
V4L/DVB (7150): [v4l] convert videbuf_vmalloc_memory to videobuf_vmalloc_memory
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Roel Kluin [Sat, 2 Feb 2008 23:20:58 +0000 (20:20 -0300)]
V4L/DVB (7139): add parentheses
'!' has a higher priority than '&': bitanding has no effect.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Luc Saillard [Wed, 30 Jan 2008 20:23:00 +0000 (17:23 -0300)]
V4L/DVB (7132): Add USB ID for a newer variant of Hauppauge WinTV-HVR 900
Device description:
WinTV-HVR-900
M/R: 65018/B3C0 ##4207
Signed-off-by: Luc Saillard <luc@saillard.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 31 Jan 2008 16:59:29 +0000 (13:59 -0300)]
V4L/DVB (7122): saa7134-empress: Remove back lock
videobuf functions at close() method already locks videobuf. It makes no sense
to keep the locking at empress close() method.
There is also a lock at open() method. I'm not sure if it is safe to remove the
locking there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 31 Jan 2008 16:57:53 +0000 (13:57 -0300)]
V4L/DVB (7121): Renames videobuf lock to vb_lock
This helps to identify where vb_lock is being used, and find missusages of the
locks.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 31 Jan 2008 16:40:04 +0000 (13:40 -0300)]
V4L/DVB (7120): videobuf lock is already initialized at videobuf-core.c
Removes the duplicated mutex_init code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss [Wed, 30 Jan 2008 04:07:20 +0000 (01:07 -0300)]
V4L/DVB (7118): dvb-ttpci: Improved display of still pictures
Improved display of still pictures (VIDEO_STILLPICTURE ioctl).
Ensure that both fields are displayed for progressive frames.
Thanks to Reinhard Nissl and Klaus Schmidinger for finding out
that the FREEZE command does this.
Thanks-to: Reinhard Nissl <rnissl@gmx.de>
Thanks-to: Klaus Schmidinger <Klaus.Schmidinger@cadsoft.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Kim Sandberg [Wed, 30 Jan 2008 03:42:01 +0000 (00:42 -0300)]
V4L/DVB (7117): budget-av: Add support for Satelco EasyWatch PCI DVB-T
Add support for Satelco EasyWatch PCI DVB-T, sub-id 0x1894:0x003a.
Signed-off-by: Kim Sandberg <ksan@saunalahti.fi>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Oliver Endriss [Wed, 30 Jan 2008 02:56:51 +0000 (23:56 -0300)]
V4L/DVB (7116): budget-av: Add support for KNC TV Station Plus X4
Add support for KNC TV Station Plus X4, sub-system id 0x1894:0x0015.
Based on a patch submitted by Johannes Deisenhofer.
Thanks-to: Johannes Deisenhofer <jo.deisenhofer@googlemail.com>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tobias Lorenz [Tue, 29 Jan 2008 01:49:14 +0000 (22:49 -0300)]
V4L/DVB (7110): Trivial printf warning fix (radio-si470)
Thanks to Darren Salt <linux@youmustbejoking.demon.co.uk> for pointing this
issue.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tobias Lorenz [Tue, 29 Jan 2008 01:43:13 +0000 (22:43 -0300)]
V4L/DVB (7108): radio-si470x.c: check-after-use
Adrian used the coverity checker against radio-si470x and found this:
> The Coverity checker spotted the following check-after-use in
> drivers/media/radio/radio-si470x.c:
>
> <-- snip -->
> static void si470x_usb_driver_disconnect(struct usb_interface *intf)
> {
> struct si470x_device *radio = usb_get_intfdata(intf);
>
> del_timer_sync(&radio->timer); <------------------
> flush_scheduled_work();
>
> usb_set_intfdata(intf, NULL);
> if (radio) { <------------------
> video_unregister_device(radio->videodev);
> kfree(radio->buffer);
> kfree(radio);
> }
> }
> <-- snip -->
>
> Either "radio" can be NULL and this case has to be properly handled or
> the NULL check is not required.
These two lines should indeed better be inside the if statement.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Bunk [Tue, 29 Jan 2008 01:10:48 +0000 (22:10 -0300)]
V4L/DVB (7106): em28xx/: make 2 functions static
This patch makes the following needlessly global functions static:
- em28xx-core.c:em28xx_write_reg_bits()
- em28xx-video.c:em28xx_vdev_init()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Bunk [Tue, 29 Jan 2008 01:10:58 +0000 (22:10 -0300)]
V4L/DVB (7104): stk-sensor.c: make 2 functions static
This patch makes the following needlessly global functions static:
- stk_sensor_outb()
- stk_sensor_inb()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Bunk [Tue, 29 Jan 2008 01:11:01 +0000 (22:11 -0300)]
V4L/DVB (7103): make stk_camera_cleanup() static
stk_camera_cleanup() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Bunk [Tue, 29 Jan 2008 01:11:15 +0000 (22:11 -0300)]
V4L/DVB (7102): make tuner-core.c:tuner_list static
tuner_list can become static - and it's anyway a way too generic name
for a global variable - see commit
b00ef4b8d8c29bfb5f6f92ee60bc04b604f36ef2
for a completely different global variable of the same name I just made
static...
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adrian Bunk [Tue, 29 Jan 2008 01:12:41 +0000 (22:12 -0300)]
V4L/DVB (7100): frontends/tda18271-common.c: fix off-by-one
This patch fixes an off-by-one error spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Matthias Schwarzott [Mon, 28 Jan 2008 15:01:11 +0000 (12:01 -0300)]
V4L/DVB (7097): saa7134-dvb: add missing dvb_attach call (for tda10046_attach)
saa7134-dvb: add missing dvb_attach around tda10046_attach
This patch adds a possibly missing dvb_attach for tda10046_attach.
This removes the hard dependency of saa7134-dvb on tda1004x module.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Sun, 27 Jan 2008 17:43:20 +0000 (14:43 -0300)]
V4L/DVB (7093): radio-sf16fmi: fix request_region()
isapnp_fmi_probe attaches device. However, if request_region() fails, the
device isn't disattached.
Reviewed-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Douglas Schilling Landgraf [Sun, 27 Jan 2008 17:29:51 +0000 (14:29 -0300)]
V4L/DVB (7092): radio-sf16fmr2: fix request_region() validation [bugzilla 9699]
This patch changed the request_region() validation to avoid invalid return.
Thanks to Roland Kletzing <devzero@web.de> for bug report and data collection.
Signed-off-by: Douglas Schilling Landgraf <dougsland@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tobias Lorenz [Sun, 27 Jan 2008 17:54:07 +0000 (14:54 -0300)]
V4L/DVB (7091): radio-si470x improvements and seldom problem fixed in tuning functions
I updated the radio-si470x driver another time. Here are the commented history entries:
- number of seek_retries changed to tune_timeout
The last versions checked for the end of frequency tuning by polling a si470x register.
Therefore polling depended on the usb utilization.
This was changed to have a constant timeout now.
- fixed problem with incomplete tune operations by own buffers
The last version used a shared buffer to assembly the USB HID reports.
It sometimes happened, that multiple functions were modifing this buffer simultanuously.
When sending such reports, the hardware returned USB stalls (-EPIPE).
Now buffers of the correct size (smaller than before) are allocated as local variables.
- optimization of variables
The size of some variables has been reduced to allow the compiler to generate more optimized code.
- improved error logging
At some important location, error checking was improved.
Especially the usb transfers to access si470x registers and the tuning functions were modified.
Signed-off-by: Tobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jaime Velasco Juan [Sun, 27 Jan 2008 15:25:00 +0000 (12:25 -0300)]
V4L/DVB (7090): V4L: stkwebcam: use v4l_compat_ioctl32
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jaime Velasco Juan [Sun, 27 Jan 2008 15:24:59 +0000 (12:24 -0300)]
V4L/DVB (7089): V4L: stkwebcam: Power management support
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Jaime Velasco Juan [Sun, 27 Jan 2008 15:24:58 +0000 (12:24 -0300)]
V4L/DVB (7088): V4L: stkwebcam: Add support for YUYV format
Signed-off-by: Jaime Velasco Juan <jsagarribay@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cyrill Gorcunov [Sat, 26 Jan 2008 10:38:01 +0000 (07:38 -0300)]
V4L/DVB (7086): driver: tcm825x - fix logical typo error
This patch does fix potential NULL pointer dereference
due to logical typo error.
The issue is pointed out by
Guennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
CC: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hermann Pitton [Sun, 20 Jan 2008 22:49:51 +0000 (19:49 -0300)]
V4L/DVB (7085): saa7134: detect the LifeView FlyDVB-T Hybrid Mini PCI
Thanks to Angelo Lisco for his initial patch we missed and to
Ahmet Dogan Ugurel confirming such a device functional.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hermann Pitton [Sun, 20 Jan 2008 22:42:01 +0000 (19:42 -0300)]
V4L/DVB (7084): saa7134: add support for the Medion / Creatix CTX948 card
This adds support for analog inputs and DVB-T.
Good sensitivity for DVB-T currently needs to use analog TV first.
DVB-S support is not yet completed, but is on the way.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hermann Pitton [Sun, 20 Jan 2008 22:32:39 +0000 (19:32 -0300)]
V4L/DVB (7083): saa7134: enable radio and external analog audio-in on the md2819
It also enumerates now the separate composite input at first
and adds mute ability to radio and external audio-in.
Many thanks to Daftcho Tabakov for reporting the flaws and testing.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hermann Pitton [Sun, 20 Jan 2008 22:27:51 +0000 (19:27 -0300)]
V4L/DVB (7082): support for Twinhan Hybrid DTV-DVB 3056 PCI
S-Video is unconfirmed, but likely correct.
The remote is not yet investigated.
Thanks go to Sioux for providing code and asking to fix the auto
detection.
Signed-off-by: sioux <sioux_it@libero.it>
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Antoine Jacquet [Sat, 26 Jan 2008 01:03:10 +0000 (22:03 -0300)]
V4L/DVB (7081): zr364xx: add support for Creative DiVi CAM 516
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Antoine Jacquet [Sat, 26 Jan 2008 01:01:53 +0000 (22:01 -0300)]
V4L/DVB (7080): zr364xx: add support for Pentax Optio 50
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Antoine Jacquet [Sat, 26 Jan 2008 01:00:19 +0000 (22:00 -0300)]
V4L/DVB (7079): zr364xx: fix typo in documentation
Signed-off-by: Antoine Jacquet <royale@zerezo.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Akinobu Mita [Sat, 19 Jan 2008 08:38:59 +0000 (05:38 -0300)]
V4L/DVB (7076): bt878: include KERN_ facility level
printk should use KERN_* levels.
CC: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Fri, 18 Jan 2008 11:53:26 +0000 (08:53 -0300)]
V4L/DVB (7049): Remove sound/driver.h
sound/driver.h is already included by sound/core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Sat, 2 Feb 2008 14:25:31 +0000 (11:25 -0300)]
V4L/DVB (7133): Fix Kconfig dependencies
As pointed by Adrian Bunk, with I2C=m and VIDEO_DEV=y, videodev brokes.
This patch moves the functions that videodev needs from v4l2-common. It also
fixes some Kconfig changes.
After this patch, I2C=m / VIDEO_DEV=y will make v4l2 core statically linked
into kernel. v4l2-common will be m, and all V4L drivers will also be m.
This approach is very conservative, since it is possible to have V4L drivers
that don't need I2C or v4l2-common. The better is to map what drivers really
need v4l2-common, making them to select v4l2-common, and allowing the others to
be 'y', 'm' and 'n'.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Thu, 31 Jan 2008 16:15:52 +0000 (13:15 -0300)]
V4L/DVB (7119): Remove obsolete code from v4l2-common
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Mauro Carvalho Chehab [Tue, 29 Jan 2008 21:32:35 +0000 (18:32 -0300)]
V4L/DVB (7115): Fix bug #9833: regression when compiling V4L without I2C
Adrian Bunk reported:
> > Commit
8ffbc6559493c64d6194c92d856196fdaeb8a5fb causes the following
> > compile error with CONFIG_VIDEO_DEV=y/m, CONFIG_I2C=n:
> >
> > <-- snip -->
> >
> > ...
> > MODPOST 26 modules
> > ERROR: "i2c_attach_client" [drivers/media/video/v4l2-common.ko] undefined!
> > make[2]: *** [__modpost] Error 1
> >
> > <-- snip -->
...
And what should happen if CONFIG_VIDEO_DEV=y, CONFIG_I2C=m?
CC: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Lachlan McIlroy [Mon, 18 Feb 2008 02:51:42 +0000 (13:51 +1100)]
Merge git://git./linux/kernel/git/torvalds/linux-2.6 into for-linus
Lachlan McIlroy [Wed, 28 Nov 2007 07:28:09 +0000 (18:28 +1100)]
[XFS] Added quota targets and removed dmapi directory
Fixes build failures introduced by bad merge to mainline.
Eric Sandeen [Tue, 27 Nov 2007 05:59:56 +0000 (16:59 +1100)]
[XFS] Fix up xfs out-of-tree builds. (a.k.a. external modules)
Change -I include directives to find headers in the out-of-tree spot. This
allows a directory containing only xfs files to be built as:
SGI-PV: 971186
SGI-Modid: xfs-linux-melb:xfs-kern:29878a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Andi Kleen [Tue, 27 Nov 2007 05:53:47 +0000 (16:53 +1100)]
[XFS] Remove Makefile wrappers in XFS
Makefile (and Kbuild) would include Makefile-linux-26 I doubt XFS will
really still compile on 2.4; so drop that. This moves Makefile-linux-26
into Makefile and drops Kbuild. Also having wrappers as both Kbuild and
Makefile seemed redundant anyways.
The patch is relatively large because it renames a file, but no functional
changes.
SGI-PV: 971050
SGI-Modid: xfs-linux-melb:xfs-kern:29781a
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Adrian Bunk [Mon, 18 Feb 2008 01:00:05 +0000 (09:00 +0800)]
[CRYPTO] null: Add missing Kconfig dependency on BLKCIPHER
This patch fixes the following build error caused by commit
3631c650c495d61b1dabf32eb26b46873636e918:
<-- snip -->
...
LD .tmp_vmlinux1
crypto/built-in.o: In function `skcipher_null_crypt':
crypto_null.c:(.text+0x3d14): undefined reference to `blkcipher_walk_virt'
crypto_null.c:(.text+0x3d14): relocation truncated to fit: R_MIPS_26 against `blkcipher_walk_virt'
crypto/built-in.o: In function `$L32':
crypto_null.c:(.text+0x3d54): undefined reference to `blkcipher_walk_done'
crypto_null.c:(.text+0x3d54): relocation truncated to fit: R_MIPS_26 against `blkcipher_walk_done'
crypto/built-in.o:(.data+0x2e8): undefined reference to `crypto_blkcipher_type'
make[1]: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pavel Machek [Mon, 4 Feb 2008 23:48:13 +0000 (00:48 +0100)]
timer_list: print relative expiry time signed
Relative expiry time can get negative, so it should be signed.
Signed-off-by: Pavel Machek <Pavel@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Chien Tung [Sat, 16 Feb 2008 03:00:36 +0000 (21:00 -0600)]
RDMA/nes: Fix VLAN support
We need to account for the VLAN header size in nes_netdev_change_mtu()
and nes_netdev_init(). Also, add spin lock/unlock during VLAN RX
registration so only one process can assign VLAN group for a given
interface at a time.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Linus Torvalds [Fri, 15 Feb 2008 23:29:23 +0000 (15:29 -0800)]
Merge branch 'upstream-linus' of git://git./linux/kernel/git/jgarzik/libata-dev
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata: fix sparse warning in pata_acpi.c
ata: fix sparse warning in pata_marvell.c
ata: fix sparse warning in pata_jmicron.c
ata: fix sparse warning in pata_cs5536.c
ata: sparse fixes for pata_amd.c
pata_scc.c: add thaw ops
pata_cs5536.c bugfix
pata_legacy: don't call ata_host_detach() after initialization failure
ata: fix sparse warnings in sata_mv.c
ata: fix sparse warning in sata_via.c
ata: fix sparse warning in sata_promise.c
ata: fix sparse warning in ata_piix.c
ata: fix sparse warning in libata-core.c
ata: make ata_scsiop_inq_89 static in libata-scsi.c