ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu

[ Upstream commit d52e5a7e7ca49457dd31fc8b42fb7c0d58a31221 ]

Prior to the rework of PMTU information storage in commit
2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.

Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.

This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().

One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.

Fixes: 2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

workqueue: use put_device() instead of kfree()

[ Upstream commit 537f4146c53c95aac977852b371bafb9c6755ee1 ]

Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized in this function instead.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Check valid VNIC ID in bnxt_hwrm_vnic_set_tpa().

[ Upstream commit 3c4fe80b32c685bdc02b280814d0cfe80d441c72 ]

During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID.  This may cause a
warning in firmware logs.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: m_can: select pinctrl state in each suspend/resume function

[ Upstream commit c9b3bce18da4a0aebc27853052dea39aa64b7d75 ]

Make sure to apply the correct pin state in suspend/resume callbacks.
Putting pins in sleep state saves power.

Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: m_can: change comparison to bitshift when dealing with a mask

[ Upstream commit b7db978ac283b237835129ac87f26cbac94d04e7 ]

Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ebtables: fix erroneous reject of last rule

[ Upstream commit 932909d9b28d27e807ff8eecb68c7748f6701628 ]

The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.

Fixes: b71812168571fa ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: mv_xor_v2: Fix clock resource by adding a register clock

[ Upstream commit 3cd2c313f1d618f92d1294addc6c685c17065761 ]

On the CP110 components which are present on the Armada 7K/8K SoC we need
to explicitly enable the clock for the registers. However it is not
needed for the AP8xx component, that's why this clock is optional.

With this patch both clock have now a name, but in order to be backward
compatible, the name of the first clock is not used. It allows to still
use this clock with a device tree using the old binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

lib/test_kmod.c: fix limit check on number of test devices created

[ Upstream commit ac68b1b3b9c73e652dc7ce0585672e23c5a2dca4 ]

As reported by Dan the parentheses is in the wrong place, and since
unlikely() call returns either 0 or 1 it's never less than zero.  The
second issue is that signed integer overflows like "INT_MAX + 1" are
undefined behavior.

Since num_test_devs represents the number of devices, we want to stop
prior to hitting the max, and not rely on the wrap arround at all.  So
just cap at num_test_devs + 1, prior to assigning a new device.

Link: http://lkml.kernel.org/r/20180224030046.24238-1-mcgrof@kernel.org
Fixes: d9c6a72d6fa2 ("kmod: add test driver to stress test the module loader")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@kernel.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/vm/run_vmtests: adjust hugetlb size according to nr_cpus

[ Upstream commit 0627be7d3c871035364923559543c9b2ff5357f2 ]

Fix userfaultfd_hugetlb on hosts which have more than 64 cpus.

  ---------------------------
  running userfaultfd_hugetlb
  ---------------------------
  invalid MiB
  Usage: <MiB> <bounces>
  [FAIL]

Via userfaultfd.c we can know, hugetlb_size needs to meet hugetlb_size
>= nr_cpus * hugepage_size.  hugepage_size is often 2M, so when host
cpus > 64, it requires more than 128M.

[zhijianx.li@intel.com: update changelog/comments and variable name]
Link: http://lkml.kernel.org/r/20180302024356.83359-1-zhijianx.li@intel.com
Link: http://lkml.kernel.org/r/20180303125027.81638-1-zhijianx.li@intel.com
Link: http://lkml.kernel.org/r/20180302024356.83359-1-zhijianx.li@intel.com
Signed-off-by: Li Zhijian <zhijianx.li@intel.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: SeongJae Park <sj38.park@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Relax ARM_SMCCC_ARCH_WORKAROUND_1 discovery

[ Upstream commit e21da1c992007594d391e7b301779cf30f438691 ]

A recent update to the ARM SMCCC ARCH_WORKAROUND_1 specification
allows firmware to return a non zero, positive value to describe
that although the mitigation is implemented at the higher exception
level, the CPU on which the call is made is not affected.

Let's relax the check on the return value from ARCH_WORKAROUND_1
so that we only error out if the returned value is negative.

Fixes: b092201e0020 ("arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: davinci: fix the GPIO lookup for omapl138-hawk

[ Upstream commit c4dc56be7e26040bfc60ce73425353516a356955 ]

The GPIO chip is called davinci_gpio.0 in legacy mode. Fix it, so that
mmc can correctly lookup the wp and cp gpios.

Note that it is the gpio-davinci driver that sets the gpiochip label to
davinci_gpio.0.

Fixes: c69f43fb4f26 ("ARM: davinci: hawk: use gpio descriptor for mmc pins")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: add a note on where the chip label is set]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: fix locking during VF setup

[ Upstream commit b0dee7910317f41f398838992516af6a3b981d86 ]

The dev_uc/mc_sync calls need to have the device address list
locked. This was spotted by running with lockdep enabled.

Fixes: bee9d41b37ea ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: fix locking for rx_mode

[ Upstream commit 35a57b7fef136fa3d5b735ba773f191b95110fa0 ]

The rx_mode operation handler is different than other callbacks
in that is not always called with rtnl held. Therefore use
RCU to ensure that references are valid.

Fixes: bee9d41b37ea ("hv_netvsc: propagate rx filters to VF")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: fix filter flags

[ Upstream commit de3d50aadd40bf68614db9fd157b275ce9c2d467 ]

The recent change to not always enable all multicast and broadcast
was broken; meant to set filter, not change flags.

Fixes: 009f766ca238 ("hv_netvsc: filter multicast/broadcast")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: xenbus: use put_device() instead of kfree()

[ Upstream commit 351b2bccede1cb673ec7957b35ea997ea24c8884 ]

Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-blkfront: move negotiate_mq to cover all cases of new VBDs

[ Upstream commit 7ed8ce1c5fc7cf25b3602c73bef897a3466a6645 ]

negotiate_mq should happen in all cases of a new VBD being discovered by
xen-blkfront, whether called through _probe() or a hot-attached new VBD
from dom-0 via xenstore. Otherwise, hot-attached new VBDs are left
configured without multi-queue.

Signed-off-by: Bhavesh Davda <bhavesh.davda@oracle.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cxgb4: do not set needs_free_netdev for mgmt dev's

[ Upstream commit b06ef18a4c255609388ed6e068a1c69c797545e0 ]

Do not set 'needs_free_netdev' as we do call free_netdev
for mgmt net devices, doing both hits BUG_ON.

Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/core: Fix possible crash to access NULL netdev

[ Upstream commit bb7f8f199c354c4cf155b1d6d55f86eaaed7fa5a ]

resolved_dev returned might be NULL as ifindex is transient number.
Ignoring NULL check of resolved_dev might crash the kernel.
Therefore perform NULL check before accessing resolved_dev.

Additionally rdma_resolve_ip_route() invokes addr_resolve() which
performs check and address translation for loopback ifindex.
Therefore, checking it again in rdma_resolve_ip_route() is not helpful.
Therefore, the code is simplified to avoid IFF_LOOPBACK check.

Fixes: 200298326b27 ("IB/core: Validate route when we init ah")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: smsc911x: Fix unload crash when link is up

[ Upstream commit e06513d78d54e6c7026c9043a39e2c01ee25bdbe ]

The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:

Call trace:
  phy_detach+0x94/0x150
  phy_disconnect+0x40/0x50
  smsc911x_stop+0x104/0x128 [smsc911x]
  __dev_close_many+0xb4/0x138
  dev_close_many+0xbc/0x190
  rollback_registered_many+0x140/0x460
  rollback_registered+0x68/0xb0
  unregister_netdevice_queue+0x100/0x118
  unregister_netdev+0x28/0x38
  smsc911x_drv_remove+0x58/0x130 [smsc911x]
  platform_drv_remove+0x30/0x50
  device_release_driver_internal+0x15c/0x1f8
  driver_detach+0x54/0x98
  bus_remove_driver+0x64/0xe8
  driver_unregister+0x34/0x60
  platform_driver_unregister+0x20/0x30
  smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
  SyS_delete_module+0x1e8/0x238
  __sys_trace_return+0x0/0x4

This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()

To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.

Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qcom/emac: Use proper free methods during TX

[ Upstream commit cc5db3150e87fe7f7e947bf333b6c1c97f848ecb ]

This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.

Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qed: Free RoCE ILT Memory on rmmod qedr

[ Upstream commit 9de506a547c0d172d13a91d69b1a399e6a2c0efa ]

Rdma requires ILT Memory to be allocated for it's QPs.
Each ILT entry points to a page used by several Rdma QPs.
To avoid allocating all the memory in advance, the rdma
implementation dynamically allocates memory as more QPs are
added, however it does not dynamically free the memory.
The memory should have been freed on rmmod qedr, but isn't.
This patch adds the memory freeing on rmmod qedr (currently
it will be freed with qed is removed).

An outcome of this bug, is that if qedr is unloaded and loaded
without unloaded qed, there will be no more RoCE traffic.

The reason these are related, is that the logic of detecting the
first QP ever opened is by asking whether ILT memory for RoCE has
been allocated.

In addition, this patch modifies freeing of the Task context to
always use the PROTOCOLID_ROCE and not the protocol passed,
this is because task context for iWARP and ROCE both use the
ROCE protocol id, as opposed to the connection context.

Fixes: dbb799c39717 ("qed: Initialize hardware for new protocols")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fsl/fman: avoid sleeping in atomic context while adding an address

[ Upstream commit 803fafbe0cd522fa6b9e41ca3b96cfb2e2a2222d ]

__dev_mc_add grabs an adress spinlock so use
atomic context in kmalloc.

/ # ifconfig eth0 inet 192.168.0.111
[   89.331622] BUG: sleeping function called from invalid context at mm/slab.h:420
[   89.339002] in_atomic(): 1, irqs_disabled(): 0, pid: 1035, name: ifconfig
[   89.345799] 2 locks held by ifconfig/1035:
[   89.349908]  #0:  (rtnl_mutex){+.+.}, at: [<(ptrval)>] devinet_ioctl+0xc0/0x8a0
[   89.357258]  #1:  (_xmit_ETHER){+...}, at: [<(ptrval)>] __dev_mc_add+0x28/0x80
[   89.364520] CPU: 1 PID: 1035 Comm: ifconfig Not tainted 4.16.0-rc3-dirty #8
[   89.371464] Call Trace:
[   89.373908] [e959db60] [c066f948] dump_stack+0xa4/0xfc (unreliable)
[   89.380177] [e959db80] [c00671d8] ___might_sleep+0x248/0x280
[   89.385833] [e959dba0] [c01aec34] kmem_cache_alloc_trace+0x174/0x320
[   89.392179] [e959dbd0] [c04ab920] dtsec_add_hash_mac_address+0x130/0x240
[   89.398874] [e959dc00] [c04a9d74] set_multi+0x174/0x1b0
[   89.404093] [e959dc30] [c04afb68] dpaa_set_rx_mode+0x68/0xe0
[   89.409745] [e959dc40] [c057baf8] __dev_mc_add+0x58/0x80
[   89.415052] [e959dc60] [c060fd64] igmp_group_added+0x164/0x190
[   89.420878] [e959dca0] [c060ffa8] ip_mc_inc_group+0x218/0x460
[   89.426617] [e959dce0] [c06120fc] ip_mc_up+0x3c/0x190
[   89.431662] [e959dd10] [c0607270] inetdev_event+0x250/0x620
[   89.437227] [e959dd50] [c005f190] notifier_call_chain+0x80/0xf0
[   89.443138] [e959dd80] [c0573a74] __dev_notify_flags+0x54/0xf0
[   89.448964] [e959dda0] [c05743f8] dev_change_flags+0x48/0x60
[   89.454615] [e959ddc0] [c0606744] devinet_ioctl+0x544/0x8a0
[   89.460180] [e959de10] [c060987c] inet_ioctl+0x9c/0x1f0
[   89.465400] [e959de80] [c05479a8] sock_ioctl+0x168/0x460
[   89.470708] [e959ded0] [c01cf3ec] do_vfs_ioctl+0xac/0x8c0
[   89.476099] [e959df20] [c01cfc40] SyS_ioctl+0x40/0xc0
[   89.481147] [e959df40] [c0011318] ret_from_syscall+0x0/0x3c
[   89.486715] --- interrupt: c01 at 0x1006943c
[   89.486715]     LR = 0x100c45ec

Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: Fixing arbitrary kernel leak in case FBIOGETCMAP_SPARC in sbusfb_ioctl_helper().

[ Upstream commit 250c6c49e3b68756b14983c076183568636e2bde ]

Fixing arbitrary kernel leak in case FBIOGETCMAP_SPARC in
sbusfb_ioctl_helper().

'index' is defined as an int in sbusfb_ioctl_helper().
We retrieve this from the user:
if (get_user(index, &c->index) ||
    __get_user(count, &c->count) ||
    __get_user(ured, &c->red) ||
    __get_user(ugreen, &c->green) ||
    __get_user(ublue, &c->blue))
       return -EFAULT;

and then we use 'index' in the following way:
red = cmap->red[index + i] >> 8;
green = cmap->green[index + i] >> 8;
blue = cmap->blue[index + i] >> 8;

This is a classic information leak vulnerability. 'index' should be
an unsigned int, given its usage above.

This patch is straight-forward; it changes 'index' to unsigned int
in two switch-cases: FBIOGETCMAP_SPARC && FBIOPUTCMAP_SPARC.

This patch fixes CVE-2018-6412.

Signed-off-by: Peter Malone <peter.malone@gmail.com>
Acked-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix an error code in __mlx5_ib_modify_qp()

[ Upstream commit 5d414b178e950ce9685c253994cc730893d5d887 ]

"err" is either zero or possibly uninitialized here.  It should be
-EINVAL.

Fixes: 427c1e7bcd7e ("{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Include GID type when deleting GIDs from HW table under RoCE

[ Upstream commit a18177925c252da7801149abe217c05b80884798 ]

The commit cited below added a gid_type field (RoCEv1 or RoCEv2)
to GID properties.

When adding GIDs, this gid_type field was copied over to the
hardware gid table. However, when deleting GIDs, the gid_type field
was not copied over to the hardware gid table.

As a result, when running RoCEv2, all RoCEv2 gids in the
hardware gid table were set to type RoCEv1 when any gid was deleted.

This problem would persist until the next gid was added (which would again
restore the gid_type field for all the gids in the hardware gid table).

Fix this by copying over the gid_type field to the hardware gid table
when deleting gids, so that the gid_type of all remaining gids is
preserved when a gid is deleted.

Fixes: b699a859d17b ("IB/mlx4: Add gid_type to GID properties")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix corruption of RoCEv2 IPv4 GIDs

[ Upstream commit 0077416a3d529baccbe07ab3242e8db541cfadf6 ]

When using IPv4 addresses in RoCEv2, the GID format for the mapped
IPv4 address should be: ::ffff:<4-byte IPv4 address>.

In the cited commit, IPv4 mapped IPV6 addresses had the 3 upper dwords
zeroed out by memset, which resulted in deleting the ffff field.

However, since procedure ipv6_addr_v4mapped() already verifies that the
gid has format ::ffff:<ipv4 address>, no change is needed for the gid,
and the memset can simply be removed.

Fixes: 7e57b85c444c ("IB/mlx4: Add support for setting RoCEv2 gids in hardware")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix iWARP write and send with immediate

[ Upstream commit 551e1c67b4207455375a2e7a285dea1c7e8fc361 ]

iWARP does not support RDMA WRITE or SEND with immediate data.
Driver should check this before submitting to FW and return an
immediate error

Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix kernel panic when running fio over NFSoRDMA

[ Upstream commit e3fd112cbf21d049faf64ba1471d72b93c22109a ]

Race in qedr_poll_cq, lastest_cqe wasn't protected by lock,
leading to a case where two context's accessing poll_cq at
the same time lead to one of them having a pointer to an old
latest_cqe and reading an invalid cqe element

Signed-off-by: Amit Radzi <Amit.Radzi@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ia64/err-inject: Use get_user_pages_fast()

[ Upstream commit 69c907022a7d9325cdc5c9dd064571e445df9a47 ]

At the point of sysfs callback, the call to gup is
done without mmap_sem (or any lock for that matter).
This is racy. As such, use the get_user_pages_fast()
alternative and safely avoid taking the lock, if possible.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: allocate ring descriptors with dma_zalloc_coherent

[ Upstream commit aea3fca005fb45f80869f2e8d56fd4e64c1d1fdb ]

Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)

This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.

Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack:      00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0:     00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0:   ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!

Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Fix check_for_link return value with autoneg off

[ Upstream commit 4e7dc08e57c95673d2edaba8983c3de4dd1f65f5 ]

When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.

Fixes: 19110cfbb34d ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf record: Fix crash in pipe mode

[ Upstream commit ad46e48c65fa1f204fa29eaff1b91174d314a94b ]

Currently we can crash perf record when running in pipe mode, like:

  $ perf record ls | perf report
  # To display the perf.data header info, please use --header/--header-only options.
  #
  perf: Segmentation fault
  Error:
  The - file has no samples!

The callstack of the crash is:

    0x0000000000515242 in perf_event__synthesize_event_update_name
  3513            ev = event_update_event__new(len + 1, PERF_EVENT_UPDATE__NAME, evsel->id[0]);
  (gdb) bt
  #0  0x0000000000515242 in perf_event__synthesize_event_update_name
  #1  0x00000000005158a4 in perf_event__synthesize_extra_attr
  #2  0x0000000000443347 in record__synthesize
  #3  0x00000000004438e3 in __cmd_record
  #4  0x000000000044514e in cmd_record
  #5  0x00000000004cbc95 in run_builtin
  #6  0x00000000004cbf02 in handle_internal_command
  #7  0x00000000004cc054 in run_argv
  #8  0x00000000004cc422 in main

The reason of the crash is that the evsel does not have ids array
allocated and the pipe's synthesize code tries to access it.

We don't force evsel ids allocation when we have single event, because
it's not needed. However we need it when we are in pipe mode even for
single event as a key for evsel update event.

Fixing this by forcing evsel ids allocation event for single event, when
we are in pipe mode.

Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180302161354.30192-1-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: rockchip: Add missing #sound-dai-cells on rk3288

[ Upstream commit 4e943a890cef42e90f43ce6be64728a290b97c55 ]

dtc now gives the following warning:

arch/arm/boot/dts/rk3288-tinker.dtb: Warning (sound_dai_property): /sound/simple-audio-card,codec: Missing property '#sound-dai-cells' in node /hdmi@ff980000 or bad phandle (referred from sound-dai[0])

Add the missing #sound-dai-cells property.

Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: propagate rx filters to VF

[ Upstream commit bee9d41b37ea6b1f860e5bc0989cf1cf1d7e6ab3 ]

The netvsc device should propagate filters to the SR-IOV VF
device (if present). The flags also need to be propagated to the
VF device as well. This only really matters on local Hyper-V
since Azure does not support multiple addresses.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: filter multicast/broadcast

[ Upstream commit 009f766ca2383d8788acd65c2c36c51bbfb19470 ]

The netvsc driver was always enabling all multicast and broadcast
even if netdevice flag had not enabled it.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hv_netvsc: use napi_schedule_irqoff

[ Upstream commit 68633edaef655ce94e51088ecef5dd4e1d2f6f34 ]

Since the netvsc_channel_cb is already called in interrupt
context from vmbus, there is no need to do irqsave/restore.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix multicast packet loss with a single WANT_ALL_IPV4/6 flag

[ Upstream commit 74c12c630fe310eb7fcae1b292257d47781fff0a ]

As the kernel doc describes too the code is supposed to skip adding
multicast TT entries if both the WANT_ALL_IPV4 and WANT_ALL_IPV6 flags
are present.

Unfortunately, the current code even skips adding multicast TT entries
if only either the WANT_ALL_IPV4 or WANT_ALL_IPV6 is present.

This could lead to IPv6 multicast packet loss if only an IGMP but not an
MLD querier is present for instance or vice versa.

Fixes: 687937ab3489 ("batman-adv: Add multicast optimization support for bridged setups")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: sbsa: use 32-bit read for WCV

[ Upstream commit 93ac3deb7c220cbcec032a967220a1f109d58431 ]

According to SBSA spec v3.1 section 5.3:
  All registers are 32 bits in size and should be accessed using
  32-bit reads and writes. If an access size other than 32 bits
  is used then the results are IMPLEMENTATION DEFINED.
  [...]
  The Generic Watchdog is little-endian

The current code uses readq to read the watchdog compare register
which does a 64-bit access. This fails on ThunderX2 which does not
implement 64-bit access to this register.

Fix this by using lo_hi_readq() that does two 32-bit reads.

Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: f71808e_wdt: Fix magic close handling

[ Upstream commit 7bd3e7b743956afbec30fb525bc3c5e22e3d475c ]

Watchdog close is "expected" when any byte is 'V' not just the last one.
Writing "V" to the device fails because the last byte is the end of string.

$ echo V > /dev/watchdog
f71808e_wdt: Unexpected close, not stopping watchdog!

Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rds: Incorrect reference counting in TCP socket creation

[ Upstream commit 84eef2b2187ed73c0e4520cbfeb874e964a0b56a ]

Commit 0933a578cd55 ("rds: tcp: use sock_create_lite() to create the
accept socket") has a reference counting issue in TCP socket creation
when accepting a new connection.  The code uses sock_create_lite() to
create a kernel socket.  But it does not do __module_get() on the
socket owner.  When the connection is shutdown and sock_release() is
called to free the socket, the owner's reference count is decremented
and becomes incorrect.  Note that this bug only shows up when the socket
owner is configured as a kernel module.

v2: Update comments

Fixes: 0933a578cd55 ("rds: tcp: use sock_create_lite() to create the accept socket")
Signed-off-by: Ka-Cheong Poon <ka-cheong.poon@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: Correctly set the tid for mcast queue

[ Upstream commit 6508de0305d560235b366cc2cc98f7bcfb029e92 ]

In the scheduler config command, the meaning of tid == 0xf was intended
to indicate the configuration is for management frames. However,
tid == 0xf was also used for the multicast queue that was meant only
for multicast data frames, which resulted with the FW not encrypting
multicast data frames.

As multicast frames do not have a QoS header, fix this by setting
tid == 0, to indicate that this is a data queue and not management
one.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: Direct multicast frames to the correct station

[ Upstream commit 7c305de2b9548ab6b65fce342c78618bbed5db73 ]

Multicast frames for NL80211_IFTYPE_AP and NL80211_IFTYPE_ADHOC were
directed to the broadcast station, however, as the broadcast station
did not have keys configured, these frames were sent unencrypted.

Fix this by using the multicast station which is the station for which
encryption keys are configured.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix "failed to remove key" message

[ Upstream commit e4f13ad07823b24a1537518d2163bd164292fb10 ]

When the GTK is installed, we install it to HW with the
station ID of the AP.

Mac80211 will try to remove it only after the AP sta is
removed, which will result in a failure to remove key
since we do not have any station for it.

This is a valid situation, but a previous commit removed
the early return and added a return with error value, which
resulted in an error message that is confusing to users.

Remove the error return value.

Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: avoid collecting firmware dump if not loaded

[ Upstream commit 8745f12a6600dd9d31122588621d4c8ddb332cd7 ]

Trying to collect firmware debug data while firmware
is not loaded causes various errors (e.g. failing NIC access).
This causes even a bigger issue if at that time the
HW radio is off.
In that case, when later turning the radio on, the Driver
fails to read the HW (registers contain garbage values).
(It may be that the CSR_GP_CNTRL_REG_FLAG_RFKILL_WAKE_L1A_EN
bit is cleared on faulty NIC access - since the same behavior
was seen in HW RFKILL toggling before setting that bit.)

Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix assert 0x2B00 on older FWs

[ Upstream commit 63dd5d022f4766e6b05ee611124afcc7cbfbb953 ]

We should add the multicast station before adding the
broadcast station.

However, in older FW, the firmware will start beaconing
when we add the multicast station, and since the broadcast
station is not added at this point so the transmission
of the beacon will fail on assert 0x2b00.

This is fixed in later firmware, so make the order
of addition depend on the TLV.

Fixes: 26d6c16bed53 ("iwlwifi: mvm: add multicast station")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: Fix channel switch for count 0 and 1

[ Upstream commit 40d53f4a60c9eb10d4fa58066c23ba1af8a59e39 ]

It was assumed that apply_time==0 implies immediate scheduling, which is
wrong. Instead, the fw expects the START_IMMEDIATELY flag to be set.
Otherwise, this resulted in 0x3063 assert.
Fix that.
While at it rename the T2_V2_START_IMMEDIATELY to
TE_V2_START_IMMEDIATELY.

Fixes: f5d8f50f271d ("iwlwifi: mvm: Fix channel switch in case of count <= 1")
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix TX of CCMP 256

[ Upstream commit de04d4fbf87b769ab18c480e4f020c53e74bbdd2 ]

We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.

Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ethtool: don't ignore return from driver get_fecparam method

[ Upstream commit a6d50512b4d86ecd9f5952525e454583be1c3b14 ]

If ethtool_ops->get_fecparam returns an error, pass that error on to the
 user, rather than ignoring it.

Fixes: 1a5f3da20bd9 ("net: ethtool: add support for forward error correction modes")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/powerpc: Skip the subpage_prot tests if the syscall is unavailable

[ Upstream commit cd4a6f3ab4d80cb919d15897eb3cbc85c2009d4b ]

The subpage_prot syscall is only functional when the system is using
the Hash MMU. Since commit 5b2b80714796 ("powerpc/mm: Invalidate
subpage_prot() system call on radix platforms") it returns ENOENT when
the Radix MMU is active. Currently this just makes the test fail.

Additionally the syscall is not available if the kernel is built with
4K pages, or if CONFIG_PPC_SUBPAGE_PROT=n, in which case it returns
ENOSYS because the syscall is missing entirely.

So check explicitly for ENOENT and ENOSYS and skip if we see either of
those.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme: pci: pass max vectors as num_possible_cpus() to pci_alloc_irq_vectors

[ Upstream commit 16ccfff2897613007b5eda9e29d65303c6280026 ]

84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
has switched to do irq vectors spread among all possible CPUs, so
pass num_possible_cpus() as max vecotrs to be assigned.

For example, in a 8 cores system, 0~3 online, 4~8 offline/not present,
see 'lscpu':

        [ming@box]$lscpu
        Architecture:          x86_64
        CPU op-mode(s):        32-bit, 64-bit
        Byte Order:            Little Endian
        CPU(s):                4
        On-line CPU(s) list:   0-3
        Thread(s) per core:    1
        Core(s) per socket:    2
        Socket(s):             2
        NUMA node(s):          2
        ...
        NUMA node0 CPU(s):     0-3
        NUMA node1 CPU(s):
        ...

1) before this patch, follows the allocated vectors and their affinity:
irq 47, cpu list 0,4
irq 48, cpu list 1,6
irq 49, cpu list 2,5
irq 50, cpu list 3,7

2) after this patch, follows the allocated vectors and their affinity:
irq 43, cpu list 0
irq 44, cpu list 1
irq 45, cpu list 2
irq 46, cpu list 3
irq 47, cpu list 4
irq 48, cpu list 6
irq 49, cpu list 5
irq 50, cpu list 7

Cc: Keith Busch <keith.busch@intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-pci: Fix EEH failure on ppc

[ Upstream commit 651438bb0af5213f1f70d66e75bf11d08cb5537a ]

Triggering PPC EEH detection and handling requires a memory mapped read
failure. The NVMe driver removed the periodic health check MMIO, so
there's no early detection mechanism to trigger the recovery. Instead,
the detection now happens when the nvme driver handles an IO timeout
event. This takes the pci channel offline, so we do not want the driver
to proceed with escalating its own recovery efforts that may conflict
with the EEH handler.

This patch ensures the driver will observe the channel was set to offline
after a failed MMIO read and resets the IO timer so the EEH handler has
a chance to recover the device.

Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
[updated change log]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: display the correct diskname for bio

[ Upstream commit 9c0fb1e313aaf4e8edec22433c8b22dd308e466c ]

bio_devname use __bdevname to display the device name, and can
only show the major and minor of the part0,
Fix this by using disk_name to display the correct name.

Fixes: 74d46992e0d9 ("block: replace bi_bdev with a gendisk pointer and partitions index")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: fix potential memory leak in init_caches()

[ Upstream commit 1c789249578895bb14ab62b4327306439b754857 ]

There is lack of cache destroy operation for ceph_file_cachep
when failing from fscache register.

Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: fix log replay failure after linking special file and fsync

[ Upstream commit 9a6509c4daa91400b52a5fd541a5521c649a8fea ]

If in the same transaction we rename a special file (fifo, character/block
device or symbolic link), create a hard link for it having its old name
then sync the log, we will end up with a log that can not be replayed and
at when attempting to replay it, an EEXIST error is returned and mounting
the filesystem fails. Example scenario:

  $ mkfs.btrfs -f /dev/sdc
  $ mount /dev/sdc /mnt
  $ mkdir /mnt/testdir
  $ mkfifo /mnt/testdir/foo
  # Make sure everything done so far is durably persisted.
  $ sync

  # Create some unrelated file and fsync it, this is just to create a log
  # tree. The file must be in the same directory as our special file.
  $ touch /mnt/testdir/f1
  $ xfs_io -c "fsync" /mnt/testdir/f1

  # Rename our special file and then create a hard link with its old name.
  $ mv /mnt/testdir/foo /mnt/testdir/bar
  $ ln /mnt/testdir/bar /mnt/testdir/foo

  # Create some other unrelated file and fsync it, this is just to persist
  # the log tree which was modified by the previous rename and link
  # operations. Alternatively we could have modified file f1 and fsync it.
  $ touch /mnt/f2
  $ xfs_io -c "fsync" /mnt/f2

  <power failure>

  $ mount /dev/sdc /mnt
  mount: mount /dev/sdc on /mnt failed: File exists

This happens because when both the log tree and the subvolume's tree have
an entry in the directory "testdir" with the same name, that is, there
is one key (258 INODE_REF 257) in the subvolume tree and another one in
the log tree (where 258 is the inode number of our special file and 257
is the inode for directory "testdir"). Only the data of those two keys
differs, in the subvolume tree the index field for inode reference has
a value of 3 while the log tree it has a value of 5. Because the same key
exists in both trees, but have different index, the log replay fails with
an -EEXIST error when attempting to replay the inode reference from the
log tree.

Fix this by setting the last_unlink_trans field of the inode (our special
file) to the current transaction id when a hard link is created, as this
forces logging the parent directory inode, solving the conflict at log
replay time.

A new generic test case for fstests was also submitted.

Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: send, fix issuing write op when processing hole in no data mode

[ Upstream commit d4dfc0f4d39475ccbbac947880b5464a74c30b99 ]

When doing an incremental send of a filesystem with the no-holes feature
enabled, we end up issuing a write operation when using the no data mode
send flag, instead of issuing an update extent operation. Fix this by
issuing the update extent operation instead.

Trivial reproducer:

  $ mkfs.btrfs -f -O no-holes /dev/sdc
  $ mkfs.btrfs -f /dev/sdd
  $ mount /dev/sdc /mnt/sdc
  $ mount /dev/sdd /mnt/sdd

  $ xfs_io -f -c "pwrite -S 0xab 0 32K" /mnt/sdc/foobar
  $ btrfs subvolume snapshot -r /mnt/sdc /mnt/sdc/snap1

  $ xfs_io -c "fpunch 8K 8K" /mnt/sdc/foobar
  $ btrfs subvolume snapshot -r /mnt/sdc /mnt/sdc/snap2

  $ btrfs send /mnt/sdc/snap1 | btrfs receive /mnt/sdd
  $ btrfs send --no-data -p /mnt/sdc/snap1 /mnt/sdc/snap2 \
       | btrfs receive -vv /mnt/sdd

Before this change the output of the second receive command is:

  receiving snapshot snap2 uuid=f6922049-8c22-e544-9ff9-fc6755918447...
  utimes
  write foobar, offset 8192, len 8192
  utimes foobar
  BTRFS_IOC_SET_RECEIVED_SUBVOL uuid=f6922049-8c22-e544-9ff9-...

After this change it is:

  receiving snapshot snap2 uuid=564d36a3-ebc8-7343-aec9-bf6fda278e64...
  utimes
  update_extent foobar: offset=8192, len=8192
  utimes foobar
  BTRFS_IOC_SET_RECEIVED_SUBVOL uuid=564d36a3-ebc8-7343-aec9-bf6fda278e64...

Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

btrfs: use kvzalloc to allocate btrfs_fs_info

[ Upstream commit a8fd1f71749387c9a1053a83ff1c16287499a4e7 ]

The srcu_struct in btrfs_fs_info scales in size with NR_CPUS.  On
kernels built with NR_CPUS=8192, this can result in kmalloc failures
that prevent mounting.

There is work in progress to try to resolve this for every user of
srcu_struct but using kvzalloc will work around the failures until
that is complete.

As an example with NR_CPUS=512 on x86_64: the overall size of
subvol_srcu is 3460 bytes, fs_info is 6496.

Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/sun4i: Fix dclk_set_phase

[ Upstream commit e64b6afa98f3629d0c0c46233bbdbe8acdb56f06 ]

Phase value is not shifted before writing.

Shift left of 28 bits to fit right bits

Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519836413-35023-1-git-send-email-giulio.benetti@micronovasrl.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: rockchip: Fix rk3399-gru-* s2r (pinctrl hogs, wifi reset)

[ Upstream commit 2560da49de5d0cfec22e9564023aebfffa094732 ]

Back in the early days when gru devices were still under development
we found an issue where the WiFi reset line needed to be configured as
early as possible during the boot process to avoid the WiFi module
being in a bad state.

We found that the way to get the kernel to do this in the earliest
possible place was to configure this line in the pinctrl hogs, so
that's what we did.  For some history here you can see
<http://crosreview.com/368770>.  After the time that change landed in
the kernel, we landed a firmware change to configure this line even
earlier.  See <http://crosreview.com/399919>.  However, even after the
firmware change landed we kept the kernel change to deal with the fact
that some people working on devices might take a little while to
update their firmware.

At this there are definitely zero devices out in the wild that have
firmware without the fix in it.  Specifically looking in the firmware
branch several critically important fixes for memory stability landed
after the patch in coreboot and I know we didn't ship without those.
Thus, by now, everyone should have the new firmware and it's safe to
not have the kernel set this up in a pinctrl hog.

Historically, even though it wasn't needed to have this in a pinctrl
hog, we still kept it since it didn't hurt.  Pinctrl would apply the
default hog at bootup and then would never touch things again.  That
all changed with commit 981ed1bfbc6c ("pinctrl: Really force states
during suspend/resume").  After that commit then we'll re-apply the
default hog at resume time and that can screw up the reset state of
WiFi.  ...and on rk3399 if you touch a device on PCIe in the wrong way
then the whole system can go haywire.  That's what was happening.
Specifically you'd resume a rk3399-gru-* device and it would mostly
resume, then would crash with some crazy weird crash.

One could say, perhaps, that the recent pinctrl change was at fault
(and should be fixed) since it changed behavior.  ...but that's not
really true.  The device tree for rk3399-gru is really to blame.
Specifically since the pinctrl is defined in the hog and not in the
"wlan-pd-n" node then the actual user of this pin doesn't have a
pinctrl entry for it.  That's bad.

Let's fix our problems by just moving the control of
"wlan_module_reset_l pinctrl" out of the hog and put them in the
proper place.

NOTE: in theory, I think it should actually be possible to have a pin
controlled _both_ by the hog and by an actual device.  Once the device
claims the pin I think the hog is supposed to let go.  I'm not 100%
sure that this works and in any case this solution would be more
complex than is necessary.

Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Fixes: 48f4d9796d99 ("arm64: dts: rockchip: add Gru/Kevin DTS")
Fixes: 981ed1bfbc6c ("pinctrl: Really force states during suspend/resume")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: Fix ESN sequence number handling for IPsec GSO packets.

[ Upstream commit b8b549eec8187ac1b12075d69a2d84d89b5e811a ]

When IPsec offloading was introduced, we accidentally incremented
the sequence number counter on the xfrm_state by one packet
too much in the ESN case. This leads to a sequence number gap of
one packet after each GSO packet. Fix this by setting the sequence
number to the correct value.

Fixes: d7dbefc45cf5 ("xfrm: Add xfrm_replay_overflow functions for offloading")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/amdgpu: Correct VRAM width for APUs with GMC9

[ Upstream commit 585b7f161c85bd5ca675b97580faf21c506541e3 ]

DDR4 has a 64-bit width not 128-bits.  It was reporting
twice the width.  Tested with my Ryzen 2400G.

Signed-off-by: Tom St Denis <tom.stdenis@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/pirq: fix error path cleanup when binding MSIs

[ Upstream commit 910f8befdf5bccf25287d9f1743e3e546bcb7ce0 ]

Current cleanup in the error path of xen_bind_pirq_msi_to_irq is
wrong. First of all there's an off-by-one in the cleanup loop, which
can lead to unbinding wrong IRQs.

Secondly IRQs not bound won't be freed, thus leaking IRQ numbers.

Note that there's no need to differentiate between bound and unbound
IRQs when freeing them, __unbind_from_irq will deal with both of them
correctly.

Fixes: 4892c9b4ada9f9 ("xen: add support for MSI message groups")
Reported-by: Hooman Mirhadi <mirhadih@amazon.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Amit Shah <aams@amazon.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/bnxt_re: Fix the ib_reg failure cleanup

[ Upstream commit 497158aa5f520db50452ef928c0f955cb42f2e77 ]

Release the netdev references in the cleanup path.  Invokes the cleanup
routines if bnxt_re_ib_reg fails.

Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/bnxt_re: Fix incorrect DB offset calculation

[ Upstream commit c354dff00db8df80f271418d8392065e10ffffb6 ]

To support host systems with non 4K page size, l2_db_size shall be
calculated with 4096 instead of PAGE_SIZE. Also, supply the host page size
to FW during initialization.

Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/bnxt_re: Unconditionly fence non wire memory operations

[ Upstream commit a45bc17b360d75fac9ced85e99fda14bf38b4dc3 ]

HW requires an unconditonal fence for all non-wire memory operations
through SQ. This guarantees the completions of these memory operations.

Signed-off-by: Devesh Sharma <devesh.sharma@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx: Set slid to zero in Ethernet completion struct

[ Upstream commit 65389322b28f81cc137b60a41044c2d958a7b950 ]

IB spec says that a lid should be ignored when link layer is Ethernet,
for example when building or parsing a CM request message (CA17-34).
However, since ib_lid_be16() and ib_lid_cpu16()  validates the slid,
not only when link layer is IB, we set the slid to zero to prevent
false warnings in the kernel log.

Fixes: 62ede7779904 ("Add OPA extended LID support")
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipvs: remove IPS_NAT_MASK check to fix passive FTP

[ Upstream commit 8a949fff0302b50063f74bb345a66190015528d0 ]

The IPS_NAT_MASK check in 4.12 replaced previous check for nfct_nat()
which was needed to fix a crash in 2.6.36-rc, see
commit 7bcbf81a2296 ("ipvs: avoid oops for passive FTP").
But as IPVS does not set the IPS_SRC_NAT and IPS_DST_NAT bits,
checking for IPS_NAT_MASK prevents PASV response to be properly
mangled and blocks the transfer. Remove the check as it is not
needed after 3.12 commit 41d73ec053d2 ("netfilter: nf_conntrack:
make sequence number adjustments usuable without NAT") which
changes nfct_nat() with nfct_seqadj() and especially after 3.13
commit b25adce16064 ("ipvs: correct usage/allocation of seqadj
ext in ipvs").

Thanks to Li Shuang and Florian Westphal for reporting the problem!

Reported-by: Li Shuang <shuali@redhat.com>
Fixes: be7be6e161a2 ("netfilter: ipvs: fix incorrect conflict resolution")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: setup cpu possible mask according to possible-cpus dts property

[ Upstream commit a29a25275452c97fe35815f1eb9564f2a07a1965 ]

As we have option in u-boot to set CPU mask for running linux,
we want to pass information to kernel about CPU cores should
be brought up. So we patch kernel dtb in u-boot to set
possible-cpus property.

This also allows us to have correctly setuped MCIP debug mask.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: mcip: update MCIP debug mask when the new cpu came online

[ Upstream commit f3205de98db2fc8083796dd5ad81b191e436fab8 ]

As of today we use hardcoded MCIP debug mask, so if we launch
kernel via debugger and kick fever cores than HW has all cpus
hang at the momemt of setup MCIP debug mask.

So update MCIP debug mask when the new cpu came online, instead of
use hardcoded MCIP debug mask.

Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: mcip: halt GFRC counter when ARC cores halt

[ Upstream commit 07423d00a2b2a71a97e4287d9262cb83c4c4c89f ]

In SMP systems, GFRC is used for clocksource. However by default the
counter keeps running even when core is halted (say when debugging via a
JTAG debugger). This confuses Linux timekeeping and triggers flase RCU stall
splat such as below:

| [ARCLinux]# while true; do ./shm_open_23-1.run-test ; done
| Running with 1000 processes for 1000 objects
| hrtimer: interrupt took 485060 ns
|
| create_cnt: 1000
| Running with 1000 processes for 1000 objects
| [ARCLinux]# INFO: rcu_preempt self-detected stall on CPU
|       2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| INFO: rcu_preempt detected stalls on CPUs/tasks:
|  0-...: (1 GPs behind) idle=71e/0/0 softirq=135264/135264 fqs=0
| 2-...: (1 GPs behind) idle=a01/1/0 softirq=135770/135773 fqs=0
| 3-...: (1 GPs behind) idle=4e0/0/0 softirq=134304/134304 fqs=0
| (detected by 1, t=13648 jiffies, g=31493, c=31492, q=1)

Starting from ARC HS v3.0 it's possible to tie GFRC to state of up-to 4
ARC cores with help of GFRC's CORE register where we set a mask for
cores which state we need to rely on.

We update cpu mask every time new cpu came online instead of using
hardcoded one or using mask generated from "possible_cpus" as we
want it set correctly even if we run kernel on HW which has fewer cores
than expected (or we launch kernel via debugger and kick fever cores
than HW has)

Note that GFRC halts when all cores have halted and thus relies on
programming of Inter-Core-dEbug register to halt all cores when one
halts.

Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
[vgupta: rewrote changelog]
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spectrum: Reference count VLAN entries

[ Upstream commit b3529af6bb0d4fe72defdd539712ceffaa054fb3 ]

One of the basic construct in the device is a port-VLAN pair, which can
be bound to a FID or a RIF in order to direct packets to the bridge or
the router, respectively.

Since not all the netdevs are configured with a VLAN (e.g., sw1p1 vs.
sw1p1.10), VID 1 is used to represent these and thus this VID can be
used by both upper devices of mlxsw ports and by the driver itself.

However, this VID is not reference counted and therefore might be freed
prematurely, which can result in various WARNINGs. For example:

$ ip link add name br0 type bridge vlan_filtering 1
$ teamd -t team0 -d -c '{"runner": {"name": "lacp"}}'
$ ip link set dev team0 master br0
$ ip link set dev enp1s0np1 master team0
$ ip address add 192.0.2.1/24 dev enp1s0np1

The enslavement to team0 will fail because team0 already has an upper
and thus vlan_vids_del_by_dev() will be executed as part of team's error
path which will delete VID 1 from enp1s0np1 (added by br0 as PVID). The
WARNING will be generated when the driver will realize it can't find VID
1 on the port and bind it to a RIF.

Fix this by adding a reference count to the VLAN entries on the port, in
a similar fashion to the reference counting used by the corresponding
'vlan_vid_info' structure in the 8021q driver.

Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Reported-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Tal Bar <talb@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mlxsw: spectrum: Treat IPv6 unregistered multicast as broadcast

[ Upstream commit 9d45deb04c59b628b21fc5014aff4f9a1d38f969 ]

When multicast snooping is enabled, the Linux bridge resorts to flooding
unregistered multicast packets to all ports only in case it did not
detect a querier in the network.

The above condition is not reflected to underlying drivers, which is
especially problematic in IPv6 environments, as multicast snooping is
enabled by default and since neighbour solicitation packets might be
treated as unregistered multicast packets in case there is no
corresponding MDB entry.

Until the Linux bridge reflects its querier state to underlying drivers,
simply treat unregistered multicast packets as broadcast and allow them
to reach their destination.

Fixes: 9df552ef3e21 ("mlxsw: spectrum: Improve IPv6 unregistered multicast flooding")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mlxsw: core: Fix flex keys scratchpad offset conflict

[ Upstream commit 2ddc94c76cc4ccaf51b478315912b38dfdde1afc ]

IP_TTL, IP_ECN and IP_DSCP are using the same offset within the
scratchpad as L4 ports. Fix this by shifting all up.

Fixes: 5f57e0909136 ("mlxsw: acl: Add ip ttl acl element")
Fixes: i80d0fe4710c ("mlxsw: acl: Add ip tos acl element")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: use link_id of server in confirm link reply

[ Upstream commit 2be922f31606f114119f48de3207d122a90e7357 ]

The CONFIRM LINK reply message must contain the link_id sent
by the server. And set the link_id explicitly when
initializing the link.

Signed-off-by: Karsten Graul <kgraul@linux.vnet.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmet: fix PSDT field check in command format

[ Upstream commit bffd2b61670feef18d2535e9b53364d270a1c991 ]

PSDT field section according to NVM_Express-1.3:
"This field specifies whether PRPs or SGLs are used for any data
transfer associated with the command. PRPs shall be used for all
Admin commands for NVMe over PCIe. SGLs shall be used for all Admin
and I/O commands for NVMe over Fabrics. This field shall be set to
01b for NVMe over Fabrics 1.0 implementations.

Suggested-by: Idan Burstein <idanb@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/tcp/illinois: replace broken algorithm reference link

[ Upstream commit ecc832758a654e375924ebf06a4ac971acb5ce60 ]

The link to the pdf containing the algorithm description is now a
dead link; it seems http://www.ifp.illinois.edu/~srikant/ has been
moved to https://sites.google.com/a/illinois.edu/srikant/ and none of
the original papers can be found there...

I have replaced it with the only working copy I was able to find.

n.b. there is also a copy available at:

http://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.296.6350&rep=rep1&type=pdf

However, this seems to only be a *cached* version, so I am unsure
exactly how reliable that link can be expected to remain over time
and have decided against using that one.

Signed-off-by: Joey Pabalinas <joeypabalinas@gmail.com>
 net/ipv4/tcp_illinois.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gianfar: Fix Rx byte accounting for ndev stats

[ Upstream commit 590399ddf9561f2ed0839311c8ae1be21597ba68 ]

Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec77118c ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.

Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource/drivers/mips-gic-timer: Use correct shift count to extract data

[ Upstream commit 5753405e27f8fe4c42c1537d3ddbd9e058e54cdc ]

__gic_clocksource_init() extracts the GIC_CONFIG_COUNTBITS field from
read_gic_config() by right shifting the register value. The shift count is
determined by the most significant bit (__fls) of the bitmask which is
wrong as it shifts out the complete bitfield.

Use the least significant bit (__ffs) instead to shift the bitfield down to
bit 0.

Fixes: e07127a077c7 ("clocksource: mips-gic-timer: Use new GIC accessor functions")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: daniel.lezcano@linaro.org
Cc: paul.burton@imgtec.com
Link: https://lkml.kernel.org/r/20180228095610.50341-1-nbd@nbd.name
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/boot: Fix random libfdt related build errors

[ Upstream commit 64c3f648c25d108f346fdc96c15180c6b7d250e9 ]

Once in a while I see build errors similar to the following
when building images from a clean tree.

  Building powerpc:virtex-ml507:44x/virtex5_defconfig ... failed
  ------------
  Error log:
  arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
   libfdt.h: No such file or directory

  Building powerpc:bamboo:smpdev:44x/bamboo_defconfig ... failed
  ------------
  Error log:
  arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
   libfdt.h: No such file or directory

  arch/powerpc/boot/treeboot-currituck.c:35:20: fatal error:
       libfdt.h: No such file or directory

Rebuilds will succeed.

Turns out that several source files in arch/powerpc/boot/ include
libfdt.h, but Makefile dependencies are incomplete. Let's fix that.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: bcm283x: Fix unit address of local_intc

[ Upstream commit 808b7de86a0c19582a7efce4c80d6b4e1da7f370 ]

This patch fixes the following DTC warning (requires W=1):
Node /soc/local_intc simple-bus unit address format error, expected "40000000"

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: NSP: Fix amount of RAM on BCM958625HR

[ Upstream commit 0a5aff64f20d92c5a6e9aeed7b5950b0b817bcd9 ]

Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.

The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.

Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nbd: fix return value in error handling path

[ Upstream commit 0979962f5490abe75b3e2befb07a564fa0cf631b ]

It seems that the proper value to return in this particular case is the
one contained into variable new_index instead of ret.

Addresses-Coverity-ID: 1465148 ("Copy-paste error")
Fixes: e46c7287b1c2 ("nbd: add a basic netlink interface")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sit: fix IFLA_MTU ignored on NEWLINK

[ Upstream commit 2b3957c34b6d7f03544b12ebbf875eee430745db ]

Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.

Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6_tunnel: fix IFLA_MTU ignored on NEWLINK

[ Upstream commit a6aa80446234ec0ad38eecdb8efc59e91daae565 ]

Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for ip6_tunnel.

Note that dev->hard_header_len setting for ip6_tunnel works fine,
no need to fix it.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip_gre: fix IFLA_MTU ignored on NEWLINK

[ Upstream commit ffc2b6ee417435605ee8bb1eb4c8f02e9ff4b4a5 ]

It's safe to remove the setting of dev's needed_headroom and mtu in
__gre_tunnel_init, as discussed in [1], ip_tunnel_newlink can do it
properly.

Now Eric noticed that it could cover the mtu value set in do_setlink
when creating a ip_gre dev. It makes IFLA_MTU param not take effect.

So this patch is to remove them to make IFLA_MTU work, as in other
ipv4 tunnels.

  [1]: https://patchwork.ozlabs.org/patch/823504/

Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.")
Reported-by: Eric Garver <e@erig.me>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: fix kcrashes with fio in RAID5 backend dev

[ Upstream commit 60eb34ec5526e264c2bbaea4f7512d714d791caf ]

Kernel crashed when run fio in a RAID5 backend bcache device, the call
trace is bellow:
[  440.012034] kernel BUG at block/blk-ioc.c:146!
[  440.012696] invalid opcode: 0000 [#1] SMP NOPTI
[  440.026537] CPU: 2 PID: 2205 Comm: md127_raid5 Not tainted 4.15.0 #8
[  440.027441] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 07/16
/2015
[  440.028615] RIP: 0010:put_io_context+0x8b/0x90
[  440.029246] RSP: 0018:ffffa8c882b43af8 EFLAGS: 00010246
[  440.029990] RAX: 0000000000000000 RBX: ffffa8c88294fca0 RCX: 0000000000
0f4240
[  440.031006] RDX: 0000000000000004 RSI: 0000000000000286 RDI: ffffa8c882
94fca0
[  440.032030] RBP: ffffa8c882b43b10 R08: 0000000000000003 R09: ffff949cb8
0c1700
[  440.033206] R10: 0000000000000104 R11: 000000000000b71c R12: 00000000000
01000
[  440.034222] R13: 0000000000000000 R14: ffff949cad84db70 R15: ffff949cb11
bd1e0
[  440.035239] FS:  0000000000000000(0000) GS:ffff949cba280000(0000) knlGS:
0000000000000000
[  440.060190] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  440.084967] CR2: 00007ff0493ef000 CR3: 00000002f1e0a002 CR4: 00000000001
606e0
[  440.110498] Call Trace:
[  440.135443]  bio_disassociate_task+0x1b/0x60
[  440.160355]  bio_free+0x1b/0x60
[  440.184666]  bio_put+0x23/0x30
[  440.208272]  search_free+0x23/0x40 [bcache]
[  440.231448]  cached_dev_write_complete+0x31/0x70 [bcache]
[  440.254468]  closure_put+0xb6/0xd0 [bcache]
[  440.277087]  request_endio+0x30/0x40 [bcache]
[  440.298703]  bio_endio+0xa1/0x120
[  440.319644]  handle_stripe+0x418/0x2270 [raid456]
[  440.340614]  ? load_balance+0x17b/0x9c0
[  440.360506]  handle_active_stripes.isra.58+0x387/0x5a0 [raid456]
[  440.380675]  ? __release_stripe+0x15/0x20 [raid456]
[  440.400132]  raid5d+0x3ed/0x5d0 [raid456]
[  440.419193]  ? schedule+0x36/0x80
[  440.437932]  ? schedule_timeout+0x1d2/0x2f0
[  440.456136]  md_thread+0x122/0x150
[  440.473687]  ? wait_woken+0x80/0x80
[  440.491411]  kthread+0x102/0x140
[  440.508636]  ? find_pers+0x70/0x70
[  440.524927]  ? kthread_associate_blkcg+0xa0/0xa0
[  440.541791]  ret_from_fork+0x35/0x40
[  440.558020] Code: c2 48 00 5b 41 5c 41 5d 5d c3 48 89 c6 4c 89 e7 e8 bb c2
48 00 48 8b 3d bc 36 4b 01 48 89 de e8 7c f7 e0 ff 5b 41 5c 41 5d 5d c3 <0f> 0b
0f 1f 00 0f 1f 44 00 00 55 48 8d 47 b8 48 89 e5 41 57 41
[  440.610020] RIP: put_io_context+0x8b/0x90 RSP: ffffa8c882b43af8
[  440.628575] ---[ end trace a1fd79d85643a73e ]--

All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.

This patch moves bio_complete() under bio_put() to avoid kernel crash.

[mlyle: fixed commit subject for character limits]

Reported-by: Matthias Ferdinand <bcache@mfedv.net>
Tested-by: Matthias Ferdinand <bcache@mfedv.net>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: rcar-dmac: fix max_chunk_size for R-Car Gen3

[ Upstream commit d716d9b702bb759dd6fb50804f10a174bd156d71 ]

According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio-gpu: fix ioctl and expose the fixed status to userspace.

[ Upstream commit 9a191b114906457c4b2494c474f58ae4142d4e67 ]

This exposes to mesa that it can use the fixed ioctl for querying
later cap sets, cap set 1 is forever frozen in time.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180221015003.22884-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

r8152: fix tx packets accounting

[ Upstream commit 4c27bf3c5b7434ccb9ab962301da661c26b467a4 ]

r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.

There is also some error since headers are accounted once, but
error rate is small enough that we do not care.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/futex: Fix line continuation in Makefile

[ Upstream commit 067b25a5639b10dfdd41ce6b4d4140fe84d0a8e7 ]

The Makefile lacks a couple of line continuation backslashes
in an `if' clause, which produces an error when make versions
prior to 4.x are used for building the tests.

  $ make
  make[1]: Entering directory `/[...]/linux/tools/testing/selftests/futex'
  /bin/sh: -c: line 5: syntax error: unexpected end of file
  make[1]: *** [all] Error 1
  make[1]: Leaving directory `/[...]/linux/tools/testing/selftests/futex'
  make: *** [all] Error 2

Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qrtr: add MODULE_ALIAS macro to smd

[ Upstream commit c77f5fbbefc04612755117775e8555c2a7006cac ]

Added MODULE_ALIAS("rpmsg:IPCRTR") to ensure qrtr-smd and qrtr will load
when IPCRTR channel is detected.

Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: orion5x: Revert commit 4904dbda41c8.

[ Upstream commit 13a55372b64e00e564a08d785ca87bd9d454ba30 ]

It is not valid for orion5x to use mac_pton().

First of all, the orion5x buffer is not NULL terminated.  mac_pton()
has no business operating on non-NULL terminated buffers because
only the caller can know that this is valid and in what manner it
is ok to parse this NULL'less buffer.

Second of all, orion5x operates on an __iomem pointer, which cannot
be dereferenced using normal C pointer operations.  Accesses to
such areas much be performed with the proper iomem accessors.

Fixes: 4904dbda41c8 ("ARM: orion5x: use mac_pton() helper")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/pvcalls: fix null pointer dereference on map->sock

[ Upstream commit 68d2059be660944152ba667e43c3b4ec225974bc ]

Currently if map is null then a potential null pointer deference
occurs when calling sock_release on map->sock.  I believe the
actual intention was to call sock_release on sock instead. Fix
this.

Fixes: 5db4d286a8ef ("xen/pvcalls: implement connect command")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: fix dentry leak when failing to init debugfs

[ Upstream commit 18106734b512664a8541026519ce4b862498b6c3 ]

When failing from ceph_fs_debugfs_init() in ceph_real_mount(),
there is lack of dput of root_dentry and it causes slab errors,
so change the calling order of ceph_fs_debugfs_init() and
open_root_dentry() and do some cleanups to avoid this issue.

Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libceph, ceph: avoid memory leak when specifying same option several times

[ Upstream commit 937441f3a3158d5510ca8cc78a82453f57a96365 ]

When parsing string option, in order to avoid memory leak we need to
carefully free it first in case of specifying same option several times.

Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource/drivers/fsl_ftm_timer: Fix error return checking

[ Upstream commit f287eb9013ccf199cbfa4eabd80c36fedfc15a73 ]

The error checks on freq for a negative error return always fails because
freq is unsigned and can never be negative. Fix this by making freq a
signed long.

Detected with Coccinelle:
drivers/clocksource/fsl_ftm_timer.c:287:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
drivers/clocksource/fsl_ftm_timer.c:291:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0

Fixes: 2529c3a33079 ("clocksource: Add Freescale FlexTimer Module (FTM) timer support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20180226113614.3092-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-pci: Fix nvme queue cleanup if IRQ setup fails

[ Upstream commit f25a2dfc20e3a3ed8fe6618c331799dd7bd01190 ]

This patch fixes nvme queue cleanup if requesting an IRQ handler for
the queue's vector fails. It does this by resetting the cq_vector to
the uninitialized value of -1 so it is ignored for a controller reset.

Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
[changelog updates, removed misc whitespace changes]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix netlink dumping of BLA backbones

[ Upstream commit fce672db548ff19e76a08a32a829544617229bc2 ]

The function batadv_bla_backbone_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.

But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.

And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.

Fixes: ea4152e11716 ("batman-adv: add backbone table netlink support")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix netlink dumping of BLA claims

[ Upstream commit b0264ecdfeab5f889b02ec54af7ca8cc1c245e2f ]

The function batadv_bla_claim_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.

But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.

And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.

Fixes: 04f3f5bf1883 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Ignore invalid batadv_v_gw during netlink send

[ Upstream commit 011c935fceae5252619ef730baa610c655281dda ]

The function batadv_v_gw_dump stops the processing loop when
batadv_v_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.

Fixes: b71bb6f924fe ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Ignore invalid batadv_iv_gw during netlink send

[ Upstream commit 10d570284258a30dc104c50787c5289ec49f3d23 ]

The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.

Fixes: efb766af06e3 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>