clk: shmobile: r8a7779: Add MSTP clock support

Add MSTP clock support for the r8a7779 SoC

The only change required appears to be to note a new
compatibility string in the bindings.

Cc: devicetree@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
(cherry picked from commit 5483bf698f42a6f0467463b064084eb888298232)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clk: shmobile: r8a7779: Add clocks support

The R8A7779 SoC has several clocks that are too custom to be supported in a
generic driver. Those clocks are all fixed rate clocks with multiplier and
divisor set according to boot mode configuration.

Based on work for R-Car Gen2 SoCs by Laurent Pinchart.

Cc: devicetree@vger.kernel.org
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
(cherry picked from commit 7b42a997bfb93c6ae0709f34ec8e2860757804b5)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7791: Correct SYS-DMAC clock defines

R-Car M2 has two MSTP bits for SYS-DMAC, not one.
Also bring the naming in sync with the documentation.

This issue was introduced in v3.14, in commit
4d8864c9e94ec727f1c675b9f6921525c360334b ("ARM: shmobile: r8a7791: Add
clock index macros for DT sources").

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit a505daa501dc3f02b08d0b48b049bce719299b74)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7790: add IIC0-2 clock macros

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 01d968e905968602c4958c416cfed7ad84b7489f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7791: Add EHCI MSTP clock

Add support for EHCI clock gating via the MSTP703 bit on r8a7791.

Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 6225b99aa620d6e260228a30cc5d24cde60cb1e7)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7791: add IIC0/1 clock macros

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit c6e8f325e769aabd059f8ff7d29e406345f83929)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7791: Rename VSP1_SY clocks to VSP1_S

The r8a7791 has three VSP1 instances, one of them being named VSPS (which
stands for "VSP Standard"). The clock section in the SoC datasheet
misunderstood the abbreviation as meaning VSP System, and named the
corresponding clock VSP1(SY). This mistake has been carried over to the
kernel code.

Fix this by renaming the VSP1_SY clock to VSP1_S.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 58ea1d53ba93620ac50fef9d9720b2323971f243)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: r8a7790: Rename VSP1_(SY|RT) clocks to VSP1_(S|R)

The r8a7790 has four VSP1 instances, two of them being named VSPS (which
stands for "VSP Standard") and VSPR (which stands for "VSP for
Resizing"). The clock section in the SoC datasheet misunderstood the
abbreviations as meaning VSP System and VSP Realtime, and named the
corresponding clocks VSP1(SY) and VSP1(RT). This mistake has been
carried over to the kernel code.

Fix this by renaming the VSP1_SY and VSP1_RT clocks to VSP1_S and VSP1_R.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 79ea9934b8df700fa306c8ced2d3bbf94ff276a8)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

dmaengine: shdma: Enable driver compilation with COMPILE_TEST

This helps increasing build testing coverage.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
(cherry picked from commit ebc6d2d9c8cd48c351da84dd467c0edddc149ded)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

gpio: rcar: Add support for DT IRQ flags

The gpio-rcar driver has no IRQ domain OF xlate function and thus
ignores IRQ flags specified in DT. Fix this by using the two-cell xlate
function.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit c058ee5a02c87710f3dc3831431abd1b9a58bd76)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

drm/rcar-du: Add run-time dependencies

The Renesas R-Car Display Unit driver is only useful on shmobile
unless build testing. The LVDS output is useful on an even more
reduced hardware set.

Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
(cherry picked from commit 923d941990e90ed8ed768b5b6cf5b9d5202b8ff1)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: host: xhci-plat: add xhci_plat_start()

Some platforms (such as the Renesas R-Car) need to initialize some specific
registers after xhci driver calls usb_add_hcd() and before the driver calls
xhci_run(). So, this patch adds the xhci_plat_start() function.

Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 94adcdce0d340e06eb9187cad70555d2e8a201f3)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: xhci: avoid warning for !PM_SLEEP

If we build a kernel with PM_SUSPEND set and no PM_SLEEP,
we get a build warning in the xhci-plat driver about unused
functions.

To fix this, use "#ifdef CONFIG_PM_SLEEP", like we do in most
other drivers nowadays.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 274f6afa298791df97fd37b7bc9d8327f5cf6ee9)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: host: xhci-plat: add support for the Armada 375/38x XHCI controllers

The Armada 375 and 38x SoCs come with an XHCI controller that requires
some specific initialization related to the MBus windows
configuration. This patch adds the support for this special
configuration as an XHCI quirk executed during probe.

Two new compatible strings are added to identify the Armada 375 and
Armada 38x XHCI controllers, and therefore enable the relevant quirk.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 973747928514bb636e3fe6a13b7ec6d6d73100f0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: host: xhci-plat: add clock support

Some platforms (such as the Armada 38x ones) can gate the clock of
their USB controller. This patch adds the support for one clock in
xhci-plat, by enabling it during probe and disabling it on remove.

To achieve this, it adds a 'struct clk *' member in xhci_hcd. While
only used for now in xhci-plat, it might be used by other drivers in
the future. Moreover, the xhci_hcd structure already holds other
members such as msix_count and msix_entries, which are MSI-X specific,
and therefore only used by xhci-pci.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 4718c177405112386a977fd9f1cba5fd6aa82315)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: host: xhci-plat: sort the headers in alphabetic order

Sorting the headers in alphabetic order will help to reduce the conflict
when adding new headers later.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 48157bb97f074d21372bd3ae87e5988ed23c8972)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

v4l: vsp1: Add DT bindings documentation

All parameters supplied through platform data can now be passed through
the device tree.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
(cherry picked from commit 34d1cbdafd5b27bc06f47f557e0581b7b85d6f07)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: sh-msiof: remove unnecessary OOM messages

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 1e8231b79ccbb3e6e7b3f6af9f998dca16b00efe)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Remove unnecessary OOM messages

The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.

[dlezcano] : refreshed against latest modifications: kmalloc -> kzalloc

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
(cherry picked from commit 814876b0b00ae98a8568d1b989bc98ca5389b98a)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Fix channel IRQ retrieval in legacy case

In the legacy platform data case each TMU platform device handles a
single channel with a single IRQ for the platform device. Retrieve the
IRQ using the logical channel number instead of the hardware channel
number.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
(cherry picked from commit c54697ae180e652a96db8bc71f0c7c7baee2bf16)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Sort headers alphabetically

This helps locating duplicates and inserting new headers.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 13931f8065fabff117828999e007f62a5cabea34)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Remove FSF mail address from GPL notice

Do not include the paragraph about writing to the Free Software
Foundation's mailing address from the sample GPL notice. The FSF has
changed addresses in the past, and may do so again. Linux already
includes a copy of the GPL.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 6b96c15b034813ec0b46e5bebbf8cffae0ac72d0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Rename clock to "fck" in the non-legacy case

The sh_tmu driver gets the TMU functional clock using a connection ID of
"tmu_fck". While all SH SoCs create clock lookup entries with a NULL
device ID and a "tmu_fck" connection ID, the ARM SoCs use the device ID
only with a NULL connection ID. This works on legacy platforms but will
break on ARM with DT boot.

Fix the situation by using a connection ID of "fck" in the non-legacy
platform data case. Clock lookup entries will be renamed to use the
device ID as well as the connection ID as platforms get moved to new
platform data. The legacy code will eventually be dropped, leaving us
with device ID based clock lookup, compatible with DT boot.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit a27d922749f3be0a88f7e0aeb507c373703c08ee)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Add support for multiple channels per device

TMU hardware devices can support multiple channels, with global
registers and per-channel registers. The sh_tmu driver currently models
the hardware with one Linux device per channel. This model makes it
difficult to handle global registers in a clean way.

Add support for a new model that uses one Linux device per timer with
multiple channels per device. This requires changes to platform data,
add new channel configuration fields.

Support for the legacy model is kept and will be removed after all
platforms switch to the new model.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 8c7f21e6739ad836f30561d641393a8417abdad3)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Hardcode TMU clock event and source ratings to 200

All boards use clock event and clock source ratings of 200 for the TMU,
hardcode it in the driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit f1010ed1a13ea38f495ebfa2fdb1f38b7f87301f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Replace hardcoded register values with macros

Define symbolic macros for all used registers bits.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 5cfe2d151f8f55052f5463e725d3d3a4aa51335d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Allocate channels dynamically

This prepares the driver for multi-channel support.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit a5de49f436e2bc498c1d13f6f8a9afaf19cb5f95)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Replace kmalloc + memset with kzalloc

One kzalloc a day keeps the bugs away.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 3b77a83eeabb885c5fff02756eba50f446a2d83c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Add index to struct sh_tmu_channel

Use the index as the timer start/stop bit and when printing messages to
identify the channel.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit fe68eb802ef8bf034735f37cb561ab814fb3b0d6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Add memory base to sh_tmu_channel structure

The channel memory base is channel-specific, add it to the channel
structure in preparation for support of multiple channels per device.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit de693461bf9624ec12808f8c5524510364cc2a43)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Constify name argument to sh_tmu_register()

The name argument is assigned to const structure fields only, constify
it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 84876d0505b15a2907696566a80a365993feab44)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Split channel setup to separate function

Move the channel setup code from sh_tmu_setup to a new
sh_tmu_setup_channel function and call it from sh_tmu_setup.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit a94ddaa6fcd46e168736027535b2d81b6a18883f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Rename struct sh_tmu_priv to sh_tmu_device

Channel data is private as well, rename priv to device to make the
distrinction between the core device and the channels clearer.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 0a72aa39cc105fbf6971feb8928a63530a4a446b)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Split channel fields from sh_tmu_priv

Create a new sh_tmu_channel structure to hold the channel-specific
field in preparation for multiple channels per device support.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit de2d12c7e856f0fa59ea83275410a364d2b182c0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

clocksource: sh_tmu: Use request_irq() instead of setup_irq()

The driver claims it needs to register an interrupt handler too early
for request_irq(). This might have been true in the past, but the only
meaningful difference between request_irq() and setup_irq() today is an
additional kzalloc() call in request_irq(). As the driver calls
kmalloc() itself we know that the slab allocator is available, we can
thus switch to request_irq().

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
(cherry picked from commit 1c56cf6b048e1e1bbe08faf38b5592b373905ac5)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

serial: sh-sci: Add device tree support for r8a7{778,740,3a4} and sh73a0

Simply document new compat strings.
There appears to be no need for a driver updates.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 34c4eda809e1efb16c554c07bb5df4c8ace9424e)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: simple-card: Support setting mclk via a fixed factor

Some platforms require that the codecs mclk is a fixed multiplication
factor of the audio stream rate. Add a optional property to the
binding to hold this factor and implement a hw_params() function to
make use of it.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 2942a0e285c46587a1025f12597df63ec04d08c6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: simple-card: is_top_level_node parameter to simple_card_dai_link_of()

Restore correct parsing of dai-link subnodes with more explicit
implementation for applying the "simple-audio-card,"-prefix to
dai-link property and subnode names.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 648722155dc081b019ab0ef548bbebde760a2b83)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: simple-card: Improve coding style

Improve indentation and space.

Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 781cbebed750af26341e551b785048a1ea347c5e)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: simple-card: Simplify error msg in simple_card_dai_link_of()

It would look better to use prop instead.

Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 966b8063607fbf43c8fdeef579fd8de8a35ca45d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: simple-card: Drop node->name checking

The current simple-card driver limits the DT node name to "sound".
Any of other names is forbidden while actually we should allow DT
to pass other node names.

And if this function is being called, the node must already have
the compatible "simple-audio-card" in DTB. So there should be no
need to check the name here.

Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 50e6c718a1eb2ae6d05f22615d8268b026175a4a)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: simple-card: Move dai-link level properties away from dai subnodes

The properties like format, bitclock-master, frame-master,
bitclock-inversion, and frame-inversion should be common to the dais
connected with a dai-link. For bitclock-master and frame-master
properties to be unambiguous they need to indicate the mastering dai
node with a phandle.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit b3ca11ff59bc5842b01f13421a17e6d9a8936784)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: core: Update snd_soc_of_parse_daifmt() interface

Adds struct device_node **bitclkmaster and struct device_node **framemaster
function parameters. With the new syntax bitclock-master and frame-master
properties can explicitly indicate the dai-link bit-clock and frame masters
with a phandle. This patch also makes the minimal changes to simple-card
for it to work with the updated snd_soc_of_parse_daifmt(). Simple-card appears
to be the only user of snd_soc_of_parse_daifmt() for now.

Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 389cb8348cf5ac4a702c71bf13673c4c8bf01e34)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: pxa: hx4700: use PWM_LOOKUP to initialize struct pwm_lookup

Use the new variant of the PWM_LOOKUP macro to initialize the PWM lookup
table.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 9becf5001130bcd24f57584e48467050e85eee03)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: armadillo: use PWM_LOOKUP to initialize struct pwm_lookup

Use the new variant of the PWM_LOOKUP macro to initialize the PWM lookup
table.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 48d6f146dced79d1df0cb91b30f1cdb749ecdf9f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: OMAP3: Beagle: use PWM_LOOKUP to initialize struct pwm_lookup

Use the new variant of the PWM_LOOKUP macro to initialize the PWM lookup
table.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit dee401e1fd5eddc8e3d6ae0e8b5c4bd64aa2a369)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pwm: modify PWM_LOOKUP to initialize all struct pwm_lookup members

Now that PWM_LOOKUP is not used anymore, modify it to initialize all the
members of struct pwm_lookup.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 4284402924cc55e182008ca7e9d4fb1e891ff5ae)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: pxa: hx4700: initialize all the struct pwm_lookup members

Instead of relying on the .pwm_period_ns member of the pwm-backlight
driver's platform data, the PWM period can be retrieved from the PWM
lookup table.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit fcb355063ffb12a834b3ca1383c9beec9285d568)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: OMAP3: Beagle: initialize all the struct pwm_lookup members

The PWM core can retrieve the period from the PWM lookup table, so the
struct led_pwm.pwm_period_ns member can be removed.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit e02a84a5ad2f46d4a262884df5ad9ab9e833a7b5)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ARM: shmobile: armadillo: initialize all struct pwm_lookup members

Initializing all the struct pwm_lookup members allows to get rid of the
struct tpu_pwm_platform_data as the polarity initialization will be
taken care of by the PWM core.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit b16001d745fbc900cc96c8ca2cd2cd08e738c421)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

DMA: shdma: add cyclic transfer support

This patch add cyclic transfer support and enables dmaengine_prep_dma_cyclic()

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
[reflown changelog for readablity]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
(cherry picked from commit dfbb85cab5f0819d0424a3637b03e7892704fa42)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PCI: rcar: Add R-Car PCIe device tree bindings

This patch adds the bindings for the R-Car PCIe driver.  The driver resides
under drivers/pci/host/pcie-rcar.c

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 7869fc6e295cbb1f80e30555bebbc795abb5b9a7)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PCI: rcar: Add MSI support for PCIe

Add MSI support to the R-Car PCIe driver.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 290c1fb35860540223bef1be021944d02232889d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

PCI: rcar: Add Renesas R-Car PCIe driver

This PCIe Host driver currently does not support MSI, so cards fall back to
INTx interrupts.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit c25da4778803b41e11fd82dd5576c35c09b5f0e0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

net: sh_eth: Fix timing of RACT setting in sh_eth_rx()

This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.

 $ sudo ping -f -l 8 $BOARD_IP_ADDR

Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 1b72a0fc9c308d9f3255c177945cf383c3c82b0e)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

net: sh_eth: Fix receive packet "exceeded" condition in sh_eth_rx()

This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 4f809cea611f1f00a0b7a42751cb12d997a4c11c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh_eth: replace devm_kzalloc() with devm_kmalloc_array()

When I was converting the driver to the managed device API, only devm_kzalloc()
was available for memory allocation, so I had to use it, despite zeroing out the
PHY IRQ array right before initializing all  its entries to PHY_POLL was quite
stupid.   Now that devm_kmalloc_array() has become available, we can avoid the
needless zeroing out...

Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(cherry picked from commit 86b5d251d5ac4dda51a022b34cb29b4ce65a8cd5)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

usb: renesas: gadget: fixup: complete STATUS stage after receiving

Current usbhs gadget driver didn't complete STATUS stage after receiving.
It wasn't problem for us before, because some USB class doesn't use
DATA OUT stage in control transfer.
But, it is required on some device.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
(cherry picked from commit 3fe15505296cb563362e2cf6d3aed73e123e0df0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pwm: add period and polarity to struct pwm_lookup

Add period and polarity members to struct pwm_lookup so that platforms
using the lookup table can be treated the same way as those using the
device tree.

Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
(cherry picked from commit 3796ce1d4d4b330a75005c5eda105603ce9d4071)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ASoC: ak4642: Fix typo zoro -> zero

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit da731845d5b47c517876cb70884789aafa00771b)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Extract rspi_common_transfer()

Extract the common parts of rspi_transfer_one(), rspi_rz_transfer_one(),
and qspi_transfer_out_in() into the new function rspi_common_transfer().

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 8b983e90ea1a3dd82070f96c062ad521a06b7cc0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Add DMA support for RSPI on RZ/A1H

Enable DMA support for RSPI on r7s72100 (RZ/A1H).

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit e7fb921d9f62df05240ad1a74b5a0f623e503c9c)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Add DMA support for QSPI on R-Car Gen2

Enable DMA support for QSPI on R-Car Gen2, for Single, Dual, and Quad SPI
Transfers.

Performance figures for reading from a QSPI FLASH driven at 24.375 MHz
on r8a7791/koelsch:
  - Single:  1.1 Mbps PIO, 23 Mbps DMA
  - Dual  : 12.7 Mbps PIO, 48 Mbps DMA
  - Quad  : 13   Mbps PIO, 70 Mbps DMA

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 4f12b5e529e4ff274eb478ec1c2ef41358ed9577)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Absorb rspi_rz_transfer_out_in() into rspi_rz_transfer_one()

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 03e627c55752fa434d5b3eba5ee3e489c51672b6)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Merge rspi_*_dma() into rspi_dma_transfer()

rspi_send_dma() and rspi_send_receive_dma() are very similar. Consolidate
into a single function rspi_dma_transfer(), and add missing checks for
dmaengine_submit() failures.

Both sg_table pointer parameters can be NULL, as RSPI supports TX-only
mode, and unidirectional DMA transfers will also be needed later for
Dual/Quad DMA support.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit c52fb6d63425248bd4152451a2cc74b7df8fa989)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Pass sg_tables instead of spi_tranfer to rspi_*_dma()

The DMA routines only need access to the scatter-gather tables inside the
spi_transfer structures, hence just pass those.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit e4b52dc4625ee739195189d40c6ddc7d55ddf312)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Move RSPI-specific setup out of DMA routines

Refactor RSPI (on SH) DMA handling to make it reusable for other RSPI
implementations:
  - Call the DMA routines after configuring the TX Mode bit and after
    calling rspi_receive_init(), so these RSPI-specific operations can be
    removed from the DMA routines,
  - Absorb rspi_transfer_out_in() into rspi_transfer_one().

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 8393fa787bf63c05cb6f9cf0a58ba1ea213c3f01)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Use SPI core DMA mapping framework

Use the SPI core DMA mapping framework instead of our own.
If available, DMA is used for transfers larger than the FIFO size
(8 or 32 bytes).

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 2f777ec91aa0623e058c43dd4aaf0b3325d3c3e8)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: SPI DMA core needs both RX and TX DMA to function

The SPI DMA core framework needs both RX and TX DMA to function.  As a
preparation for converting the driver to use this framework, fall back to
PIO if no DMA channel or only one DMA channel is available.

This affects only RSPI, which could do DMA transfers for TX-only before.
RSPI-RZ and QSPI (at least for Single SPI Transfers) will need both RX and
TX DMA anyway.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 5f338d0ce0b4c9e6c554b92cfb288789a41bfbc1)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Remove unneeded resource test in DMA setup

The resource is know to exist, as rspi_probe() already mapped it.
Remove the test, and just pass the resource.
Pass the device pointer instead of the platform device pointer, as the
latter is no longer needed.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit fcdc49ae53dc8cfc1a7758607bca68935f568ca2)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Extract rspi_request_dma_chan()

Setup of the receive and transmit DMA channels is very similar, so let's
consolidate.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 65bf220571f131a7c3a564a88793bd0f16fd7c96)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Don't consider DMA configuration failures fatal

Fall back to PIO if DMA configuration failed.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 27e105a6006b8ce1b55709c5e24f63959981475d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Extract rspi_pio_transfer()

The various PIO loops are very similar. Consolidate into a single
function rspi_pio_transfer().

Both buffer pointers can be NULL, as RSPI supports TX-only mode, and
Dual/Quad SPI Transfers are unidirectional.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 6837b8e91d2a080293c30d5fe42d9692390091fa)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Use core SPI_MASTER_MUST_[RT]X handling

RSPI needs dummy transfers to generate the SPI clock on receive.
RSPI-RZ and QSPI always do both transmit and receive.

Use the SPI core SPI_MASTER_MUST_RX/SPI_MASTER_MUST_TX infrastructure
instead of checking for the presence of buffers and providing dummy data
ourselves (for PIO), or providing a dummy buffer (for DMA).

rspi_receive_dma() now provides full duplex DMA transfers on RSPI, and is
renamed to rspi_send_receive_dma().

As the SPI core will always provide a TX buffer, the logic to choose
between DMA send and DMA send/receive in rspi_transfer_one() now has to
check for the presence of an RX buffer. Likewise for the DMA availability
tests in rspi_is_dma().

The buffer tests in qspi_transfer_one() are now always true, so they're
removed.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit b42e03596db3d45980c976c8124fdc323f031dc4)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Remove unused 16-bit DMA support

The 16-bit DMA support doesn't fit well within the SPI core DMA framework,
as it needs to manage its own double-sized temporary buffers, for handling
the interleaved data.
Remove it, as there is no in-tree board code that sets
rspi_plat_data.dma_width_16bit.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 9c5de2c1754c2bb3c69c4d7bf0d0edc0a61d8232)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Do not call rspi_receive_init() for TX-only

Since commit 8449fd76deb9ac67a15a6fb8ead7bb4595d019d2 ("spi: rspi: Merge
rspi_send_pio() and rspi_receive_pio()"), rspi_receive_init() is called
for transmit-only transfers too, while this is not needed.
Only call rspi_receive_init() when receiving, to preserve behavior on
RSPI on SH.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 32c64261c6f50a4e71ec7546f7e2f48eba91c985)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Extract rspi_wait_for_{tx_empty,rx_full}()

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 5f684c34fc82be84ece158aa5c5c7c5072daa9a0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

spi: rspi: Round up division to avoid slave overclocking

The calculation of the bit rate divider used a standard C division, which
rounds down the quotient. This may lead to a higher bitrate than requested.
Round up to avoid this.

E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75
MHz. After this patch it's driven at a safe 24.375 MHz.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
(cherry picked from commit 3beb61dbfcf188399cbc36ce1eeb8b2ba724de38)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

drivers: sh: Enable PM runtime for new R-Car Gen2 SoCs

The PM runtime code should also be enabled for:
  - r8a7792 (R-Car V2H)
  - r8a7793 (R-Car M2-N)
  - r8a7794 (R-Car E2)

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 2f35fb3c8a6018a0a5fe4a7fb0948b853c157256)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

drivers: sh: pm_runtime implementation needs to suspend and resume devices

If we override the platform bus calls for pm_runtime then we end up
with the calls to the devices' suspend and resume methods ignored
in favour of the bus ones.

Change to calling the pm_runtime calls to suspend and resume the
devices specifically in the drivers/sh/pm_runtime.c implementation
to allow any device that may want to run power management to do so.

Note, all the current sh driver implementations do not use their
own power management code so this is not a major implementation
issues.

This also brings the implementation into line with the versions
used by the Davinci and Keystone PM domain code, so once fully
tested these implementations could be merged together.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 8255fe169232364e5a01bd062e8037b8c1a9adec)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

drivers: sh: Restrict INTC_USERIMASK to SH4A

register_intc_userimask() is called from sh4a code only.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> [r8a7779 legacy]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit 39c5abbc54179998bf04368a11c561e19220d7d4)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

drivers: sh: pm_runtime does not need idle callback

In the runtime_pm idle callback the code assumes that a NULL .runtime_idle
entry is the same as a .runtime_idle entry that returns 0 as a result. This
means the entry in drivers/sh/pm_runtime can be removed in favour of just
leaving the entry NULL.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> [r8a7779 legacy]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
(cherry picked from commit fe95c932a31e7f12bcb6a4e07434462da2ac6e1d)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh: intc: Remove pointless irq_reserve_irqs() invocation

The preceding call to irq_create_identity_mapping() marks the
interrupt as allocated already. Remove the leftover.

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Acked-by: Simon Horman <horms@verge.net.au>
Cc: linux-sh@vger.kernel.org
Link: http://lkml.kernel.org/r/20140507154339.189047829@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
(cherry picked from commit 3670802223e164f1089287d1c223d34d3c5dc3da)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh: clk: Use cpufreq_for_each_valid_entry macro for iteration

The cpufreq core now supports the cpufreq_for_each_valid_entry macro
helper for iteration over the cpufreq_frequency_table, so use it.

It should have no functional changes.

Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 4229e1c61a4a7ac21d5d0790f6add1c9b98d33e7)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

cpufreq: Fix build error on some platforms that use cpufreq_for_each_*

On platforms that use cpufreq_for_each_* macros, build fails if
CONFIG_CPU_FREQ=n, e.g. ARM/shmobile/koelsch/non-multiplatform:

drivers/built-in.o: In function `clk_round_parent':
clkdev.c:(.text+0xcf168): undefined reference to `cpufreq_next_valid'
drivers/built-in.o: In function `clk_rate_table_find':
clkdev.c:(.text+0xcf820): undefined reference to `cpufreq_next_valid'
make[3]: *** [vmlinux] Error 1

Fix this making cpufreq_next_valid function inline and move it to
cpufreq.h.

Fixes: 27e289dce297 (cpufreq: Introduce macros for cpufreq_frequency_table iteration)
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 5eeaf1f1897372590105f155c6a7110b3fa36aef)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Conflicts:
include/linux/cpufreq.h

cpufreq: Introduce macros for cpufreq_frequency_table iteration

Many cpufreq drivers need to iterate over the cpufreq_frequency_table
for various tasks.

This patch introduces two macros which can be used for iteration over
cpufreq_frequency_table keeping a common coding style across drivers:

- cpufreq_for_each_entry: iterate over each entry of the table
- cpufreq_for_each_valid_entry: iterate over each entry that contains
a valid frequency.

It should have no functional changes.

Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
(cherry picked from commit 27e289dce29764e488c1e13e9aa6950cad1f4aab)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: sh_mmcif: clarify DDR timing mode between SD-UHS and eMMC

Replaced UHS_DDR50 with MMC_DDR52.

CC: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
(cherry picked from commit 4039ff4741c6e8d27b5ca42dc92d87dc2d625b80)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

mmc: clarify DDR timing mode between SD-UHS and eMMC

This change distinguishes DDR timing mode of current
mixed usage to clarify device type.

Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
(cherry picked from commit 79f7ae7c45a6ccf04e2908337461dee615f6afb0)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

serial: sh-sci: Add device tree support for r8a7779

Simply document a new compat string.
There appears to be no need for a driver updates.

Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 81bd1eb7af751666ace2f1dadb0b0101401807cd)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Revert "serial: sh-sci: Add device tree support for r8a7779"

This reverts commit fcbee4d49f30eb0eaa83a62e6a3cab5a892ed93f.

It wasn't quite ready to go in yet, sorry about that.

Cc: Simon Horman <horms@verge.net.au>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit 2aafb3864b9fa5ce83250537d940f973ef37b8dc)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

serial: sh-sci: Add device tree support for r8a7779

According to the platform data for the legacy-C initialisation of sh-sci
for the r8a7779 SoC and my own testing the SCIx_SH4_SCIF_REGTYPE bit of
scscr needs to be set.

Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
(cherry picked from commit fcbee4d49f30eb0eaa83a62e6a3cab5a892ed93f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: sh-pfc: r8a73a4: Allow Multiplatform Build

Add #ifdefs to allow r8a73a4 Multiplatform build. Needed
to enable r8a73a4 Multiplatform support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit f39d8a72feb073c4ef6296f1d12cedf2ed572bfb)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: sh-pfc: sh73a0: Allow Multiplatform Build

Add #ifdefs to allow sh73a0 Multiplatform build. Needed
to enable sh73a0 Multiplatform support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 672d32377494b84d6af483ce46eda07baba4e3ea)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: sh-pfc: r8a7740: Allow Multiplatform Build

Add #ifdefs to allow r8a7740 Multiplatform build. Needed
to enable r8a7740 Multiplatform support.

Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit b6c996a295620b67e4033f2eb07e5a5cf9e7a48f)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: sh-pfc: Don't set the pinmux_irq irq field for multiplatform

In the multiplatform kernel case the IRQs associated with the PFC GPIOs
are specified through DT. The pinmux_irq irq field is thus ignored by
the code, and doesn't need to be set.

This will allow removing the mach/irq.h include from pfc-*.c files that
was required for the irq_pin() macro used to initialize the irq field.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 0e26e8dfb9dddb0559fb7cd7b53a8b497a8d4121)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: pfc: r8a7790: add mux data for IIC(B) cores

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit a16b81dcbfc5889c37dac5f8e836136e4740fc18)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: pfc: r8a7790: add i2c0 muxing

Add the muxing for the last missing i2c rcar core. Fix the sorting for
SH_PFC_PIN_NAMED while we are here.

Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit 35a493de0daf4955b6d15d488b3f8754d4637a04)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh-pfc: r8a7791: Add Audio pin support

Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit c57a05b0eb0ee0205b34f2694b035afc75fa71e4)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

sh-pfc: r8a7791: Add SSI pin support

Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit b664cd1f020211d8e4480c2937b82fe513a9c757)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

pinctrl: sh-pfc: r8a7791: Split the DU sync and cde/disp groups

The DU parallel interface ODDF signal is optional, move it out of the
HSYNC/VSYNC group into a group of its down. The CDE and DISP signals are
independent, split them to two different groups.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit d10046e25c73e6150677b1b5360f20bb631181a7)
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>