pasemi_mac: Clean TX ring in poll

Unfortunately there's no timeout for how long a packet can sit on
the TX ring after completion before an interrupt is generated, and
we want to have a threshold that's larger than one packet per interrupt.

So we have to have a timer that occasionally cleans the TX ring even
though there hasn't been an interrupt. Instead of setting up a dedicated
timer for this, just clean it in the NAPI poll routine instead.

[ Resolved conflicts with napi_struct changes... -DaveM ]

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi_mac: Enable LLTX

Enable LLTX on pasemi_mac: we're already doing sufficient locking
in the driver to enable it.

[ Resolved merge conflicts with napi_struct changes... -DaveM ]

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi_mac: Fix RX checksum flags

RX side flag to use is CHECKSUM_UNNECESSARY, not CHECKSUM_COMPLETE.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi_mac: Fix TX ring wrap checking

The old logic didn't detect full (tx) ring cases properly, causing
overruns and general badness. Clean it up a bit and abstract out the
ring size checks, always making sure to leave 1 slot open.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi_mac: Batch up TX buffer frees

Postpone pci unmap and skb free of the transmitted buffers to outside of
the tx ring lock, batching them up 32 at a time.

Also increase the count threshold to 128.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi_mac: RX performance tweaks

Various RX performance tweaks, do some explicit prefetching of packet
data, etc.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi_mac: Fix memcpy amount for short receives

Fix up memcpy for short receives.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi_mac: Enable L2 caching of packet headers

Enable settings to target l2 for the first few cachelines of the packet, since
we'll access them to get to the various headers.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pasemi_mac: Stop using the pci config space accessors for register read/writes

Move away from using the pci config access functions for simple register
access.  Our device has all of the registers in the config space (hey,
from the hardware point of view it looks reasonable :-), so we need to
somehow get to it. Newer firmwares have it in the device tree such that
we can just get it and ioremap it there (in case it ever moves in future
products). For now, provide a hardcoded fallback for older firmwares.

[ Resolved napi_struct conflicts... -DaveM ]

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

pasemi_mac: Abstract out register access

Abstract out the PCI config read/write accesses into reg read/write ones,
still calling the pci accessors on the back end.

Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bmac: add simple ethtool support for network manager

NetworkManager will not start dhcpd on an interface unless it reports
link-up state via ethtool.

Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sky2: use pci_config access functions

Use the PCI layer config access functions. The driver was using the
memory mapped window in device, to workaround issues accessing the
advanced error reporting registers.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: advanced error reporting

Use the kernel interfaces for advanced error reporting.
This should be cleaner and clear up errors on boot.

For those systems with busted BIOS's that don't correctly
support mmconfig, advanced error reporting will be disabled.
The PCI registers for advanced error reporting start at 0x100 which
is too large to be accessed by legacy functions.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sky2: dont restrict config space access

Take out the code that protects driver from accessing the
PCI config space.
We are old enough to run with scissors now.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sky2: document GPHY_CTRL bits

Add documentation of GPHY_CTRL register bits even if driver
is not using them (yet).

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

sky2: use debugfs rename

Use debugfs rename to handle device neame changes.

Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - Update internal memory management

Set PM1 internal memory to round robin mode
It balances access to this internal memory for multiport adapters.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - log adapter serial number

Log HW serial number when cxgb3 module is loaded.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - Fatal error update

Stop the MAC when a fatal error is detected.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - tighten checks on TID values

Enforce validity checks on connection ids

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - Expose HW memory page info

A HW issue requires limiting the receive window size
to 23 pages of internal memory.
These pages can be configured to different sizes,
thus the RDMA driver needs to know the
page size to enforce the upper limit.

Also assign explicit enum values.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - use immediate data for offload Tx

Send small TX_DATA work requests as immediate data even when
there are fragments. this avoids doing multiple DMAs for
small fragmented packets.
The driver already implements this optimization for small
contiguous packets.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - SGE doorbell overflow warning

Log doorbell Fifo overflow

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - Update rx coalescing length

Reduce Rx coalescing length to 12288
Large bursts from the adapter to the host create back pressure
on the chip. Reducing the burst size avoids the issue.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

3c59x: check return of pci_enable_device()

Check return of pci_enable_device in vortex_up().

Also modify vortex_up to return error to callers. Handle failure of
vortex_up in vortex_open and vortex_resume.

Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ibmveth: Remove use of bitfields

Removes the use of bitfields from the ibmveth driver. This results
in slightly smaller object code.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ibmveth: Remove dead frag processing code

Removes dead frag processing code from ibmveth. Since NETIF_F_SG was
not set, this code was never executed. Also, since the ibmveth
interface can only handle 6 fragments, core networking code would need
to be modified in order to efficiently enable this support.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ibmveth: Add ethtool driver stats hooks

Add ethtool hooks to ibmveth to retrieve driver statistics.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ibmveth: Add ethtool TSO handlers

Add handlers for get_tso and get_ufo to prevent errors being printed
by ethtool.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ibmveth: Implement ethtool hooks to enable/disable checksum offload

This patch adds the appropriate ethtool hooks to allow for enabling/disabling
of hypervisor assisted checksum offload for TCP.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

ibmveth: Enable TCP checksum offload

This patchset enables TCP checksum offload support for IPV4
on ibmveth. This completely eliminates the generation and checking of
the checksum for packets that are completely virtual and never
touch a physical network. A simple TCP_STREAM netperf run on
a virtual network with maximum mtu set yielded a ~30% increase
in throughput. This feature is enabled by default on systems that
support it, but can be disabled with a module option.

Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

dl2k: add Sundance/Tamarack TC902x Gigabit Ethernet Adapter support

Actually, D-Link modified the VendorID/ProductID of the TC902x.
The TC902x is the original chipset.

Signed-off-by: Komuro <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

uli526x: Add suspend and resume routines (updated)

Add suspend/resume support to the uli526x network driver (tested on x86_64,
with 'Ethernet controller: ALi Corporation M5263 Ethernet Controller, rev 40').

This patch is based on the suspend/resume code in the tg3 driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

pcnet32: add suspend and resume capability

Add suspend and resume capability to the driver.
Tested both to ram and to disk on x86_64 platform.

Signed-off-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

support for USB autosuspend in the asix driver

this implements support for USB autosuspend in the asix USB ethernet
driver.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)

This driver implements support for the ICH9 on-board LAN ethernet
device. The device is similar to ICH8.

The driver encompasses code to support 82571/2/3, es2lan and ICH8
devices as well, but those device IDs are disabled and will be
"lifted" from the e1000 driver over one at a time once this driver
receives some more live time.

Changes to the last snapshot posted are exclusively in the internal
hardware API organization. Many thanks to Jeff Garzik for jumping in
and getting this organized with a keen eye on the future layout.

[ Integrated napi_struct patch from Auke as well... -DaveM ]

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[PATCH] libertas: remove unused adhoc_rates_b definition

Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: printk warning fixes

drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_helper':
drivers/net/wireless/libertas/if_cs.c:462: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'
drivers/net/wireless/libertas/if_cs.c: In function 'if_cs_prog_real':
drivers/net/wireless/libertas/if_cs.c:538: warning: format '%d' expects type 'int', but argument 3 has type 'size_t'

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] net: Kill some unneeded allocation return value casts in libertas

kmalloc() and friends return void*, no need to cast it.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: advertise 11g ad-hoc rates

Advertise support for 802.11g bitrates when starting adhoc
networks, not just 802.11b bitrates.

Signed-off-by: Brajesh Dave <brajeshd@marvell.com>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: region code values specified as 8bit

This patch strips away possible mess in regioncode (eg. on my card - 88W8305
chipset - I get 0x3031 instead of expected 0x0031 and as a result the driver
defaults to USA region which is obviously incorrect). Following patch fixes
the issue.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: properly end commands on hardware failure

Make sure that errors reported by the hardware layer is properly
handled. Otherwise commands tend to get stuck in limbo.

Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: send reset command directly instead of calling libertas_reset_device

Ensures that any platform specific code that might live in libertas_reset_device
(for example, OLPC tells the EC to do a GPIO-toggled reset of the wireless
from libertas_reset_device) isn't called.  Could be handled better by
interface-specific callbacks and a flag for "other hardware reset".

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: don't stomp on interface-specific private data

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: reorganize and simplify init sequence

This patch moves all firmware load responsibility into the interface-specific
code and gets rid of the firmware pointer in the generic card structure.  It
also removes 3 fairly unecessary callbacks: hw_register_dev, hw_unregister_dev,
and hw_prog_firmware.  It also makes the init sequence from interface
probe functions more logical, as there are paired add/remove and start/stop
calls into generic libertas code.

Because the USB driver code uses the same TX URB callback for both firmware
upload (where the generic libertas structure isn't initialized yet) and for
normal operation (where it is), some bits of USB code have to deal with
'priv' being NULL.  All USB firmware upload bits have been changed to not
require 'priv' at all, but simply the USB card structure.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix inadvertant removal of bits from commit 831441862956fffa17b9801db37e6ea1650b0f69

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] drivers/net/wireless/wl3501_cs.c: remove redundant memset

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] zd1211rw: Add ID for ZyXEL M-202 XtremeMIMO

Tested by Nathen Meyers
FCC ID: SI5WUB221Z
zd1211b chip 0586:340a v4810 high 00-13-49 AL2230_RF pa0 ----S

Despite the product name, I'm pretty sure this isn't a MIMO device. It
appears just to be a normal ZD1211B and we have never heard of these
devices having more than 1 RF. I guess they named this product this way
to make it appear that it fits in with the rest of their XtremeMIMO
product range.

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] zd1211rw: consistent handling of ZD1211 specific rates

As pointed out by Daniel Drake, the zd1211rw driver used several
different rate values and names throughout the driver. He has
written a patch to change it and tweaked it after some pretty wild
ideas from my side. But the discussion helped me to understand the
problem better and I think I have nailed it down with this patch.

A zd-rate will consist from now on of a four-bit "pure" rate value
and a modulation type flag as used in the ZD1211 control set used
for packet transmission. This is consistent with the usage in the
zd_rates table. If possible these zd-rates should be used in the
code.

Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] zd1211rw: Add ID for Sitecom WL-162

Tested by Giuseppe Lippolis
zd1211b chip 0cde:001a v4810 high 00-60-b3 AL2230_RF pa0 g--NS

Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] zd1211rw: removed noisy debug messages

While developing the driver we added a lot of debug messages for
setting hardware registers. These messages make the reading of the
log files difficult and are of no use anymore. This patch removes
those messages in zd_chip.c.

Signed-off-by: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

xen-netfront: remove dead code

This patch removes some residual dead code left over from removing the
"flip" receive mode.  This patch doesn't change the generated output
at all, since gcc already realized it was dead.

This resolves the "regression" reported by Adrian.

Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Adrian Bunk <bunk@stusta.de>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/3c505: Convert to generic boolean

Convert to generic boolean

Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/tokenring: Convert to generic boolean

Convert to generic boolean

Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/tokenring/3c359.c

Hi,
   Replacing kmalloc with kzalloc and cleaning up memset in
drivers/net/tokenring/3c359.c

Signed-off-by: Surya Prabhakar <surya.prabhakar@wipro.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

cxgb3 - MAC workaround update

Update the MAC workaround to deal with switches that do not
honor pause frames.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] drivers/net: remove superfluous memset

This patch covers something like this:

dev = alloc_*dev(...
...
priv = netdev_priv(dev);
memset(priv, 0, sizeof(*priv));

The memset() here is superfluous. alloc_netdev() uses kzalloc()
to allocate needed memory so there is no need to zero the priv region
twice.

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up duplicate includes in drivers/net/

This patch cleans up duplicate includes in
 drivers/net/

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[netdrvr] ns83820: add ethtool media support

Split out from patch authored by Dan Faerch <dan@hacker.dk>.

Signed-off-by: Jeff Garzik <jeff@garzik.org>

net/tulip/xircom_cb.c: remove superfulous priv assignment

Unpatched version does sth like this:

dev = alloc_etherdev(...
private = netdev_priv(dev);
...
dev->priv = private;

which doesn't make much sense (does it?) because this is done in
alloc_netdev() already.

struct net_device *alloc_netdev(...
{
...
if (sizeof_priv)
dev->priv = netdev_priv(dev);

This patch removes superfluous code.

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
 drivers/net/tulip/xircom_cb.c | 32853 -> 32831 (-22 bytes)
 drivers/net/tulip/xircom_cb.o | 123984 -> 123984 (0 bytes)

 drivers/net/tulip/xircom_cb.c |    1 -
 1 file changed, 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>

S2IO: Fixed Link LED issue when MSI-X is enabled

-Fixed Link LED issue when MSI-X is enabled.

Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

S2IO: Fixes in MSIX related code.

- Calling store_xmsi_data to store the MSI-X datas during initialization
  in s2io-init_nic function
- Disabling NAPI when MSI-X is enabled
- Freeing sp->entries and sp->s2io_entries in s2io_rem_isr

Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[S2IO]: Making MSIX as default intr_type

- Making MSIX as default intr_type
- Driver will test MSI-X by issuing test MSI-X vector and if fails it will
  fallback to INTA

Signed-off-by: Sivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[8139too]: tab-align enums and structs; remove dead code

* (main change) tab-align hardware register value enums, and hw struct

* MMIO_FLUSH_AUDIT_COMPLETE has been defined to 1 for a while.  Remove
  the code activated when it is set to zero.

Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

[netdrvr] 8139cp, 8139too: convert to generic DMA

Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/via-velocity.c: mostly kmalloc + memset conversion to kcalloc

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
 drivers/net/via-velocity.c | 88263 -> 88120 (-143 bytes)
 drivers/net/via-velocity.o | 254264 -> 253828 (-436 bytes)

 drivers/net/via-velocity.c |   24 ++++++++++--------------
 1 file changed, 10 insertions(+), 14 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/sb1250-mac.c: kmalloc + memset conversion to kcalloc

Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
 drivers/net/sb1250-mac.c | 76286 -> 76199 (-87 bytes)

 drivers/net/sb1250-mac.c |    6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/skfp: Remove dead code referencing pci_find_device()

Signed-off-by: Jeff Garzik <jeff@garzik.org>

IOC3: Switch hw checksumming to ethtool configurable.

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

drivers/net/cxgb3: removed several unneeded zero initilization

Cc: linux-bugs@chelsio.com
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

dev->priv to netdev_priv(dev), drivers/net/tokenring/

Replacing accesses to dev->priv to netdev_priv(dev). The replacment
is safe when netdev_priv is used to access a private structure that is
right next to the net_device structure in memory.
Cf http://groups.google.com/group/comp.os.linux.development.system/browse_thread/thread/de19321bcd94dbb8/0d74a4adcd6177bd
This is the case when the net_device structure was allocated with
a call to alloc_netdev or one of its derivative.

Here is an excerpt of the semantic patch that performs the transformation

@ rule1 @
type T;
struct net_device *dev;
@@

 dev =
(
        alloc_netdev
|
        alloc_etherdev
|
        alloc_trdev
)
   (sizeof(T), ...)

@ rule1bis @
struct net_device *dev;
expression E;
@@
 dev->priv = E

@ rule2 depends on rule1 && !rule1bis  @
struct net_device *dev;
type rule1.T;
@@

- (T*) dev->priv
+ netdev_priv(dev)

PS: I have performed the same transformation on the whole kernel
and it affects around 70 files, most of them in drivers/net/.
Should I split my patch for each subnet directories ? (wireless/, wan/, etc)

Thanks to Thomas Surrel for helping me refining my semantic patch.

Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
 3c359.c       |   58 +++++++++++++++++++++++++++++-----------------------------
 ibmtr.c       |   38 +++++++++++++++++++-------------------
 lanstreamer.c |   32 ++++++++++++++++----------------
 madgemc.c     |    4 ++--
 olympic.c     |   36 ++++++++++++++++++------------------
 tmspci.c      |    4 ++--
 6 files changed, 86 insertions(+), 86 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>

[netdrvr] skfp: remove a bunch of dead code

The driver has not compiled in anything except PCI support for many
years (see drivers/net/skfp/Makefile).  This driver is also unmaintained
for many years, so arguments for keeping the cross-OS, cross-bus (ISA,
EISA, MCA) code do not exist.

Signed-off-by: Jeff Garzik <jeff@garzik.org>

[PATCH] libertas: bump driver version

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix sparse-reported problems

A few fields being converted to the wrong sized type, and a few missed
endian conversions.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: better descriptions for association errors

Describe the association response status code the firmware
returns, based on mail to libertas-dev from Ronak.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: ignore spurious mesh autostart events

Don't trust the firmware to always send them at the right time,
ignore them when the driver thinks mesh autostart is disabled.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix misspelling in debug message

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: pass boot2 version to firmware

Boot2 version used to be hardcoded in the uploaded firmware,
this patch preserves the boot2 version before uploading firmware
and sends it to the firmware again on resume.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: push WEXT scan requests to a work queue

Push WEXT scan requests to a workqueue and have each partial scan queue
the next part, then only report results when the complete scan has finished.
Full scans don't go through the work queue.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] drivers/net/wireless/libertas/cmd.c: fix adapter->driver_lock dereference

adapter is NULL if cmdnode is not.

Signed-off-by: Eugene Teo <eugeneteo@kernel.sg>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix assignment of WEP key type

keytype is a u8

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: monitor mode support for OLPC firmware

Driver support for the monitor mode support that will be available in the next
OLPC 'bleeding edge' Marvell firmware release (most likely, 5.110.16.p2).

To activate monitor mode,

echo mode > /sys/class/net/{ethX,mshX}/device/libertas_rtap

where mode is the hex mask that specifies which frames to sniff (in short, 0x1
for data, 0x2 for all management but beacons, 0x4 for beacons). Any non zero
mode will activate the monitor mode, inhibiting transmission in ethX and mshX
interfaces and routing all the incoming traffic to a new rtapX interface that
will output the packets in 802.11+radiotap headers format.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix a few wext abuses...

o SIOCGIWNAME is not designed to return the version number of the driver.
On the other hand, you are free to abuse SIOCGIWNICKN for that purpose.

o Don't attempt to fix the WE19/WE20 transition in the driver, because
your fixes are bogus, and redundant with the code in the kernel (you may
endup with +2, you can't read 32 char ESSID...).

o In SIOCSIWTXPOW, if you specified in iwrange that you want dBm, you
should only get dBm, which allow to reduce code bloat.

Signed-off-by: Jean Tourrilhes <jt@hpl.hp.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: keep mesh autostart enabled while asleep

After loading the firmware, mesh autostart will be disabled. After that, the
user will still be able to enable or disable it at will. On suspend, it will be
always activated and later on resume it will go back to the state it had before
going to sleep.

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: revert CAPINFO_MASK to its original value

CAPINFO_MASK changed on commits 981f187b and a091095b. Reverting to the original
value.  Also move CAPINFO_MASK into the sole user, join.c.  CAPINFO_MASK
should be in host CPU byte order; capability is converted to device
byte order elsewhere.

This fixes OLPC ticket #2161

Signed-off-by: Luis Carlos Cobo <luisca@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: push mesh beacon bit to userspace in scan results

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: send association events on adhoc reassociation

Send association event to userspace when reassociating to the same
ad-hoc network, because it's still an association.

Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: fix two debug statements in cmdresp.c

Purely cosmetic: this moves an lbs_deb_enter() to the proper place
and changes an erraneous lbs_deb_enter_args() into lbs_deb_leave_args()

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove bss_descriptor->timestamp

Noone used this variable.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove bss_descriptior->networktsf

This value was parsed out, but then nowhere used ... except in
some debugfs output. I can't imagine anyone wanting to use this
value for anything real (as no other driver exports it), so
bye-bye.

Along this, made the columns of
/sys/kernel/debug/libertas_wireless/*/getscantable align again.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->scantype

scantype was initialized with CMD_SCAN_TYPE_ACTIVE, but there is no code
that would ever change it, so we can use that variable directly.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->scanmode

scanmode was initialized with CMD_BSS_TYPE_ANY, but there is no code
that ever can store another value there, so it can go away.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->beaconperiod

beaconperiod was initialized with MRVDRV_BEACON_INTERVAL, but there is
no code that would ever change it's value. We can use the define directly.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->adhoc_grate_enabled

The variable was initialized with 0 (false). There is no code that would
ever change it, so we can use the false-patch directly.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->listeninterval

listeninterval was initialized with MRVDRV_DEFAULT_LISTEN_INTERVAL, but
there exists that would ever change it. So we can use this define directly.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->regiontableindex

The value was computed, but then never used.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->atimwindow

This varaible was initialized with 0 but there is no code that would ever
change it's value. So it can go away.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->multipledtim

multipledtim was initialized with MRVDRV_DEFAULT_MULTIPLE_DTIM and then
kept at that value, so we could use that define directly.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->locallisteninterval

locallisteninterval was initialized with 0, but there is no code that
changes it, rendering it rather useless.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

[PATCH] libertas: remove adapter->nullpktinterval

No code ever initialized this variable, so it was 0 because of kzalloc().
But no other code changes it, making it rather useless.

Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>