review.tizen.org Git - platform/kernel/linux-rpi.git/log

ASoC: cs42l51: Correct PGA Volume minimum value

[ Upstream commit 3d1bb6cc1a654c8693a85b1d262e610196edec8b ]

The table in the datasheet actually shows the volume values in the wrong
order, with the two -3dB values being reversed. This appears to have
caused the lower of the two values to be used in the driver when the
higher should have been, correct this mixup.

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221125162348.1288005-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: fec: don't reset irq coalesce settings to defaults on "ip link up"

[ Upstream commit df727d4547de568302b0ed15b0d4e8a469bdb456 ]

Currently, when a FEC device is brought up, the irq coalesce settings
are reset to their default values (1000us, 200 frames). That's
unexpected, and breaks for example use of an appropriate .link file to
make systemd-udev apply the desired
settings (https://www.freedesktop.org/software/systemd/man/systemd.link.html),
or any other method that would do a one-time setup during early boot.

Refactor the code so that fec_restart() instead uses
fec_enet_itr_coal_set(), which simply applies the settings that are
stored in the private data, and initialize that private data with the
default values.

Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: mcba_usb: Fix termination command argument

[ Upstream commit 1a8e3bd25f1e789c8154e11ea24dc3ec5a4c1da0 ]

Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've observed, both with my oscilloscope and captured USB packets
below, you must send "0" to turn it ON, and "1" to turn it OFF.

From the schematics in the user's guide, I can confirm that you must
drive the CAN_RES signal LOW "0" to activate the resistors.

Reverse the argument value of usb_msg.termination to fix this.

These are the two commands sequence, ON then OFF.

> No.     Time           Source                Destination           Protocol Length Info
>       1 0.000000       host                  1.3.1                 USB      46     URB_BULK out
>
> Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80000000000000000000000000000000000a8
>
> No.     Time           Source                Destination           Protocol Length Info
>       2 4.372547       host                  1.3.1                 USB      46     URB_BULK out
>
> Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80100000000000000000000000000000000a9

Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Link: https://lore.kernel.org/all/20221124152504.125994-1-yashi@spacecubics.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: sja1000: fix size of OCR_MODE_MASK define

[ Upstream commit 26e8f6a75248247982458e8237b98c9fb2ffcf9d ]

bitfield mode in ocr register has only 2 bits not 3, so correct
the OCR_MODE_MASK define.

Signed-off-by: Heiko Schocher <hs@denx.de>
Link: https://lore.kernel.org/all/20221123071636.2407823-1-hs@denx.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: meditatek: Startup with the IRQs disabled

[ Upstream commit 11780e37565db4dd064d3243ca68f755c13f65b4 ]

If the system is restarted via kexec(), the peripherals do not start
with a known state.

If the previous system had enabled an IRQs we will receive unexected
IRQs that can lock the system.

[   28.109251] watchdog: BUG: soft lockup - CPU#0 stuck for 26s!
[swapper/0:0]
[   28.109263] Modules linked in:
[   28.109273] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
5.15.79-14458-g4b9edf7b1ac6 #1 9f2e76613148af94acccd64c609a552fb4b4354b
[   28.109284] Hardware name: Google Elm (DT)
[   28.109290] pstate: 40400005 (nZcv daif +PAN -UAO -TCO -DIT -SSBS
BTYPE=--)
[   28.109298] pc : __do_softirq+0xa0/0x388
[   28.109309] lr : __do_softirq+0x70/0x388
[   28.109316] sp : ffffffc008003ee0
[   28.109321] x29: ffffffc008003f00 x28: 000000000000000a x27:
0000000000000080
[   28.109334] x26: 0000000000000001 x25: ffffffefa7b350c0 x24:
ffffffefa7b47480
[   28.109346] x23: ffffffefa7b3d000 x22: 0000000000000000 x21:
ffffffefa7b0fa40
[   28.109358] x20: ffffffefa7b005b0 x19: ffffffefa7b47480 x18:
0000000000065b6b
[   28.109370] x17: ffffffefa749c8b0 x16: 000000000000018c x15:
00000000000001b8
[   28.109382] x14: 00000000000d3b6b x13: 0000000000000006 x12:
0000000000057e91
[   28.109394] x11: 0000000000000000 x10: 0000000000000000 x9 :
ffffffefa7b47480
[   28.109406] x8 : 00000000000000e0 x7 : 000000000f424000 x6 :
0000000000000000
[   28.109418] x5 : ffffffefa7dfaca0 x4 : ffffffefa7dfadf0 x3 :
000000000000000f
[   28.109429] x2 : 0000000000000000 x1 : 0000000000000100 x0 :
0000000001ac65c5
[   28.109441] Call trace:
[   28.109447]  __do_softirq+0xa0/0x388
[   28.109454]  irq_exit+0xc0/0xe0
[   28.109464]  handle_domain_irq+0x68/0x90
[   28.109473]  gic_handle_irq+0xac/0xf0
[   28.109480]  call_on_irq_stack+0x28/0x50
[   28.109488]  do_interrupt_handler+0x44/0x58
[   28.109496]  el1_interrupt+0x30/0x58
[   28.109506]  el1h_64_irq_handler+0x18/0x24
[   28.109512]  el1h_64_irq+0x7c/0x80
[   28.109519]  arch_local_irq_enable+0xc/0x18
[   28.109529]  default_idle_call+0x40/0x140
[   28.109539]  do_idle+0x108/0x290
[   28.109547]  cpu_startup_entry+0x2c/0x30
[   28.109554]  rest_init+0xe8/0xf8
[   28.109562]  arch_call_rest_init+0x18/0x24
[   28.109571]  start_kernel+0x338/0x42c
[   28.109578]  __primary_switched+0xbc/0xc4
[   28.109588] Kernel panic - not syncing: softlockup: hung tasks

Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Link: https://lore.kernel.org/r/20221122-mtk-pinctrl-v1-1-bedf5655a3d2@chromium.org
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

libbpf: Use page size as max_entries when probing ring buffer map

[ Upstream commit 689eb2f1ba46b4b02195ac2a71c55b96d619ebf8 ]

Using page size as max_entries when probing ring buffer map, else the
probe may fail on host with 64KB page size (e.g., an ARM64 host).

After the fix, the output of "bpftool feature" on above host will be
correct.

Before :
    eBPF map_type ringbuf is NOT available
    eBPF map_type user_ringbuf is NOT available

After :
    eBPF map_type ringbuf is available
    eBPF map_type user_ringbuf is available

Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20221116072351.1168938-2-houtao@huaweicloud.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()

[ Upstream commit 97eea946b93961fffd29448dcda7398d0d51c4b2 ]

The bounds checks in snd_soc_put_volsw_sx() are only being applied to the
first channel, meaning it is possible to write out of bounds values to the
second channel in stereo controls. Add appropriate checks.

Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220511134137.169575-2-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_micfil: explicitly clear CHnF flags

[ Upstream commit b776c4a4618ec1b5219d494c423dc142f23c4e8f ]

There may be failure when start 1 channel recording after
8 channels recording. The reason is that the CHnF
flags are not cleared successfully by software reset.

This issue is triggerred by the change of clearing
software reset bit.

CHnF flags are write 1 clear bits. Clear them by force
write.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1651925654-32060-2-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_micfil: explicitly clear software reset bit

[ Upstream commit 292709b9cf3ba470af94b62c9bb60284cc581b79 ]

SRES is self-cleared bit, but REG_MICFIL_CTRL1 is defined as
non volatile register, it still remain in regmap cache after set,
then every update of REG_MICFIL_CTRL1, software reset happens.
to avoid this, clear it explicitly.

Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1651925654-32060-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nfp: fix use-after-free in area_cache_get()

commit 02e1a114fdb71e59ee6770294166c30d437bf86a upstream.

area_cache_get() is used to distribute cache->area and set cache->id,
and if cache->id is not 0 and cache->area->kref refcount is 0, it will
release the cache->area by nfp_cpp_area_release(). area_cache_get()
set cache->id before cpp->op->area_init() and nfp_cpp_area_acquire().

But if area_init() or nfp_cpp_area_acquire() fails, the cache->id is
is already set but the refcount is not increased as expected. At this
time, calling the nfp_cpp_area_release() will cause use-after-free.

To avoid the use-after-free, set cache->id after area_init() and
nfp_cpp_area_acquire() complete successfully.

Note: This vulnerability is triggerable by providing emulated device
equipped with specified configuration.

BUG: KASAN: use-after-free in nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
Write of size 4 at addr ffff888005b7f4a0 by task swapper/0/1

Call Trace:
<TASK>
nfp6000_area_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:760)
area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:884)

Allocated by task 1:
nfp_cpp_area_alloc_with_name (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:303)
nfp_cpp_area_cache_add (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:802)
nfp6000_init (drivers/net/ethernet/netronome/nfp/nfpcore/nfp6000_pcie.c:1230)
nfp_cpp_from_operations (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:1215)
nfp_pci_probe (drivers/net/ethernet/netronome/nfp/nfp_main.c:744)

Freed by task 1:
kfree (mm/slub.c:4562)
area_cache_get.constprop.8 (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:873)
nfp_cpp_read (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:924 drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cppcore.c:973)
nfp_cpp_readl (drivers/net/ethernet/netronome/nfp/nfpcore/nfp_cpplib.c:48)

Signed-off-by: Jialiang Wang <wangjialiang0806@163.com>
Reviewed-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220810073057.4032-1-wangjialiang0806@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vfs: fix copy_file_range() averts filesystem freeze protection

commit 10bc8e4af65946b727728d7479c028742321b60a upstream.

Commit 868f9f2f8e00 ("vfs: fix copy_file_range() regression in cross-fs
copies") removed fallback to generic_copy_file_range() for cross-fs
cases inside vfs_copy_file_range().

To preserve behavior of nfsd and ksmbd server-side-copy, the fallback to
generic_copy_file_range() was added in nfsd and ksmbd code, but that
call is missing sb_start_write(), fsnotify hooks and more.

Ideally, nfsd and ksmbd would pass a flag to vfs_copy_file_range() that
will take care of the fallback, but that code would be subtle and we got
vfs_copy_file_range() logic wrong too many times already.

Instead, add a flag to explicitly request vfs_copy_file_range() to
perform only generic_copy_file_range() and let nfsd and ksmbd use this
flag only in the fallback path.

This choise keeps the logic changes to minimum in the non-nfsd/ksmbd code
paths to reduce the risk of further regressions.

Fixes: 868f9f2f8e00 ("vfs: fix copy_file_range() regression in cross-fs copies")
Tested-by: Namjae Jeon <linkinjeon@kernel.org>
Tested-by: Luis Henriques <lhenriques@suse.de>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[backport comments for v5.15: - sb_write_started() is missing - assert was dropped ]
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/vdso: Conditionally export __vdso_sgx_enter_enclave()

commit 45be2ad007a9c6bea70249c4cf3e4905afe4caeb upstream.

Recently, ld.lld moved from '--undefined-version' to
'--no-undefined-version' as the default, which breaks building the vDSO
when CONFIG_X86_SGX is not set:

ld.lld: error: version script assignment of 'LINUX_2.6' to symbol '__vdso_sgx_enter_enclave' failed: symbol not defined

__vdso_sgx_enter_enclave is only included in the vDSO when
CONFIG_X86_SGX is set. Only export it if it will be present in the final
object, which clears up the error.

Fixes: 8466436952017 ("x86/vdso: Implement a vDSO for Intel SGX enclave call")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/1756
Link: https://lore.kernel.org/r/20221109000306.1407357-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.15.83

Link: https://lore.kernel.org/r/20221212130926.811961601@linuxfoundation.org
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Bagas Sanjaya <bagasdotme@gmail.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Kelsey Steele <kelseysteele@linux.microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()

[ Upstream commit 998b30c3948e4d0b1097e639918c5cff332acac5 ]

Syzkaller reports a NULL deref bug as follows:

BUG: KASAN: null-ptr-deref in io_tctx_exit_cb+0x53/0xd3
Read of size 4 at addr 0000000000000138 by task file1/1955

CPU: 1 PID: 1955 Comm: file1 Not tainted 6.1.0-rc7-00103-gef4d3ea40565 #75
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.11.0-2.el7 04/01/2014
Call Trace:
  <TASK>
  dump_stack_lvl+0xcd/0x134
  ? io_tctx_exit_cb+0x53/0xd3
  kasan_report+0xbb/0x1f0
  ? io_tctx_exit_cb+0x53/0xd3
  kasan_check_range+0x140/0x190
  io_tctx_exit_cb+0x53/0xd3
  task_work_run+0x164/0x250
  ? task_work_cancel+0x30/0x30
  get_signal+0x1c3/0x2440
  ? lock_downgrade+0x6e0/0x6e0
  ? lock_downgrade+0x6e0/0x6e0
  ? exit_signals+0x8b0/0x8b0
  ? do_raw_read_unlock+0x3b/0x70
  ? do_raw_spin_unlock+0x50/0x230
  arch_do_signal_or_restart+0x82/0x2470
  ? kmem_cache_free+0x260/0x4b0
  ? putname+0xfe/0x140
  ? get_sigframe_size+0x10/0x10
  ? do_execveat_common.isra.0+0x226/0x710
  ? lockdep_hardirqs_on+0x79/0x100
  ? putname+0xfe/0x140
  ? do_execveat_common.isra.0+0x238/0x710
  exit_to_user_mode_prepare+0x15f/0x250
  syscall_exit_to_user_mode+0x19/0x50
  do_syscall_64+0x42/0xb0
  entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0023:0x0
Code: Unable to access opcode bytes at 0xffffffffffffffd6.
RSP: 002b:00000000fffb7790 EFLAGS: 00000200 ORIG_RAX: 000000000000000b
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
  </TASK>
Kernel panic - not syncing: panic_on_warn set ...

This happens because the adding of task_work from io_ring_exit_work()
isn't synchronized with canceling all work items from eg exec. The
execution of the two are ordered in that they are both run by the task
itself, but if io_tctx_exit_cb() is queued while we're canceling all
work items off exec AND gets executed when the task exits to userspace
rather than in the main loop in io_uring_cancel_generic(), then we can
find current->io_uring == NULL and hit the above crash.

It's safe to add this NULL check here, because the execution of the two
paths are done by the task itself.

Cc: stable@vger.kernel.org
Fixes: d56d938b4bef ("io_uring: do ctx initiated file note removal")
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20221206093833.3812138-1-harshit.m.mogalapalli@oracle.com
[axboe: add code comment and also put an explanation in the commit msg]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

io_uring: move to separate directory

[ Upstream commit ed29b0b4fd835b058ddd151c49d021e28d631ee6 ]

In preparation for splitting io_uring up a bit, move it into its own
top level directory. It didn't really belong in fs/ anyway, as it's
not a file system only API.

This adds io_uring/ and moves the core files in there, and updates the
MAINTAINERS file for the new location.

Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 998b30c3948e ("io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: move CONFIG_BLOCK guard to top Makefile

[ Upstream commit 4c928904ff771a8e830773b71a080047365324a5 ]

Every object under block/ depends on CONFIG_BLOCK.

Move the guard to the top Makefile since there is no point to
descend into block/ if CONFIG_BLOCK=n.

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20210927140000.866249-5-masahiroy@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Stable-dep-of: 998b30c3948e ("io_uring: Fix a null-ptr-deref in io_tctx_exit_cb()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: esd_usb: Allow REC and TEC to return to zero

[ Upstream commit 918ee4911f7a41fb4505dff877c1d7f9f64eb43e ]

We don't get any further EVENT from an esd CAN USB device for changes
on REC or TEC while those counters converge to 0 (with ecc == 0). So
when handling the "Back to Error Active"-event force txerr = rxerr =
0, otherwise the berr-counters might stay on values like 95 forever.

Also, to make life easier during the ongoing development a
netdev_dbg() has been introduced to allow dumping error events send by
an esd CAN USB device.

Fixes: 96d8e90382dc ("can: Add driver for esd CAN-USB/2 device")
Signed-off-by: Frank Jungclaus <frank.jungclaus@esd.eu>
Link: https://lore.kernel.org/all/20221130202242.3998219-2-frank.jungclaus@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/qeth: fix use-after-free in hsci

[ Upstream commit ebaaadc332cd21e9df4dcf9ce12552d9354bbbe4 ]

KASAN found that addr was dereferenced after br2dev_event_work was freed.

==================================================================
BUG: KASAN: use-after-free in qeth_l2_br2dev_worker+0x5ba/0x6b0
Read of size 1 at addr 00000000fdcea440 by task kworker/u760:4/540
CPU: 17 PID: 540 Comm: kworker/u760:4 Tainted: G E 6.1.0-20221128.rc7.git1.5aa3bed4ce83.300.fc36.s390x+kasan #1
Hardware name: IBM 8561 T01 703 (LPAR)
Workqueue: 0.0.8000_event qeth_l2_br2dev_worker
Call Trace:
[<000000016944d4ce>] dump_stack_lvl+0xc6/0xf8
[<000000016942cd9c>] print_address_description.constprop.0+0x34/0x2a0
[<000000016942d118>] print_report+0x110/0x1f8
[<0000000167a7bd04>] kasan_report+0xfc/0x128
[<000000016938d79a>] qeth_l2_br2dev_worker+0x5ba/0x6b0
[<00000001673edd1e>] process_one_work+0x76e/0x1128
[<00000001673ee85c>] worker_thread+0x184/0x1098
[<000000016740718a>] kthread+0x26a/0x310
[<00000001672c606a>] __ret_from_fork+0x8a/0xe8
[<00000001694711da>] ret_from_fork+0xa/0x40
Allocated by task 108338:
kasan_save_stack+0x40/0x68
kasan_set_track+0x36/0x48
__kasan_kmalloc+0xa0/0xc0
qeth_l2_switchdev_event+0x25a/0x738
atomic_notifier_call_chain+0x9c/0xf8
br_switchdev_fdb_notify+0xf4/0x110
fdb_notify+0x122/0x180
fdb_add_entry.constprop.0.isra.0+0x312/0x558
br_fdb_add+0x59e/0x858
rtnl_fdb_add+0x58a/0x928
rtnetlink_rcv_msg+0x5f8/0x8d8
netlink_rcv_skb+0x1f2/0x408
netlink_unicast+0x570/0x790
netlink_sendmsg+0x752/0xbe0
sock_sendmsg+0xca/0x110
____sys_sendmsg+0x510/0x6a8
___sys_sendmsg+0x12a/0x180
__sys_sendmsg+0xe6/0x168
__do_sys_socketcall+0x3c8/0x468
do_syscall+0x22c/0x328
__do_syscall+0x94/0xf0
system_call+0x82/0xb0
Freed by task 540:
kasan_save_stack+0x40/0x68
kasan_set_track+0x36/0x48
kasan_save_free_info+0x4c/0x68
____kasan_slab_free+0x14e/0x1a8
__kasan_slab_free+0x24/0x30
__kmem_cache_free+0x168/0x338
qeth_l2_br2dev_worker+0x154/0x6b0
process_one_work+0x76e/0x1128
worker_thread+0x184/0x1098
kthread+0x26a/0x310
__ret_from_fork+0x8a/0xe8
ret_from_fork+0xa/0x40
Last potentially related work creation:
kasan_save_stack+0x40/0x68
__kasan_record_aux_stack+0xbe/0xd0
insert_work+0x56/0x2e8
__queue_work+0x4ce/0xd10
queue_work_on+0xf4/0x100
qeth_l2_switchdev_event+0x520/0x738
atomic_notifier_call_chain+0x9c/0xf8
br_switchdev_fdb_notify+0xf4/0x110
fdb_notify+0x122/0x180
fdb_add_entry.constprop.0.isra.0+0x312/0x558
br_fdb_add+0x59e/0x858
rtnl_fdb_add+0x58a/0x928
rtnetlink_rcv_msg+0x5f8/0x8d8
netlink_rcv_skb+0x1f2/0x408
netlink_unicast+0x570/0x790
netlink_sendmsg+0x752/0xbe0
sock_sendmsg+0xca/0x110
____sys_sendmsg+0x510/0x6a8
___sys_sendmsg+0x12a/0x180
__sys_sendmsg+0xe6/0x168
__do_sys_socketcall+0x3c8/0x468
do_syscall+0x22c/0x328
__do_syscall+0x94/0xf0
system_call+0x82/0xb0
Second to last potentially related work creation:
kasan_save_stack+0x40/0x68
__kasan_record_aux_stack+0xbe/0xd0
kvfree_call_rcu+0xb2/0x760
kernfs_unlink_open_file+0x348/0x430
kernfs_fop_release+0xc2/0x320
__fput+0x1ae/0x768
task_work_run+0x1bc/0x298
exit_to_user_mode_prepare+0x1a0/0x1a8
__do_syscall+0x94/0xf0
system_call+0x82/0xb0
The buggy address belongs to the object at 00000000fdcea400
which belongs to the cache kmalloc-96 of size 96
The buggy address is located 64 bytes inside of
96-byte region [00000000fdcea400, 00000000fdcea460)
The buggy address belongs to the physical page:
page:000000005a9c26e8 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0xfdcea
flags: 0x3ffff00000000200(slab|node=0|zone=1|lastcpupid=0x1ffff)
raw: 3ffff00000000200 0000000000000000 0000000100000122 000000008008cc00
raw: 0000000000000000 0020004100000000 ffffffff00000001 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
00000000fdcea300: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
00000000fdcea380: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
>00000000fdcea400: fa fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
^
00000000fdcea480: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
00000000fdcea500: fb fb fb fb fb fb fb fb fb fb fb fb fc fc fc fc
==================================================================

Fixes: f7936b7b2663 ("s390/qeth: Update MACs of LEARNING_SYNC device")
Reported-by: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Reviewed-by: Thorsten Winkler <twinkler@linux.ibm.com>
Link: https://lore.kernel.org/r/20221207105304.20494-1-wintera@linux.ibm.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/qeth: fix various format strings

[ Upstream commit 22e2b5cdb0b9b59d4df6da5ca9bc5773a4f8e3ea ]

Various format strings don't match with types of parameters.
Fix all of them.

Acked-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: ebaaadc332cd ("s390/qeth: fix use-after-free in hsci")
Signed-off-by: Sasha Levin <sashal@kernel.org>

macsec: add missing attribute validation for offload

[ Upstream commit 38099024e51ee37dee5f0f577ca37175c932e3f7 ]

Add missing attribute validation for IFLA_MACSEC_OFFLOAD
to the netlink policy.

Fixes: 791bb3fcafce ("net: macsec: add support for specifying offload upon link creation")
Signed-off-by: Emeel Hakim <ehakim@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20221207101618.989-1-ehakim@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mvneta: Fix an out of bounds check

[ Upstream commit cdd97383e19d4afe29adc3376025a15ae3bab3a3 ]

In an earlier commit, I added a bounds check to prevent an out of bounds
read and a WARN(). On further discussion and consideration that check
was probably too aggressive. Instead of returning -EINVAL, a better fix
would be to just prevent the out of bounds read but continue the process.

Background: The value of "pp->rxq_def" is a number between 0-7 by default,
or even higher depending on the value of "rxq_number", which is a module
parameter. If the value is more than the number of available CPUs then
it will trigger the WARN() in cpu_max_bits_warn().

Fixes: e8b4fc13900b ("net: mvneta: Prevent out of bounds read in mvneta_config_rss()")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/Y5A7d1E5ccwHTYPf@kadam
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: thunderbolt: fix memory leak in tbnet_open()

[ Upstream commit ed14e5903638f6eb868e3e2b4e610985e6a6c876 ]

When tb_ring_alloc_rx() failed in tbnet_open(), ida that allocated in
tb_xdomain_alloc_out_hopid() is not released. Add
tb_xdomain_release_out_hopid() to the error path to release ida.

Fixes: 180b0689425c ("thunderbolt: Allow multiple DMA tunnels over a single XDomain connection")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20221207015001.1755826-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv6: avoid use-after-free in ip6_fragment()

[ Upstream commit 803e84867de59a1e5d126666d25eb4860cfd2ebe ]

Blamed commit claimed rcu_read_lock() was held by ip6_fragment() callers.

It seems to not be always true, at least for UDP stack.

syzbot reported:

BUG: KASAN: use-after-free in ip6_dst_idev include/net/ip6_fib.h:245 [inline]
BUG: KASAN: use-after-free in ip6_fragment+0x2724/0x2770 net/ipv6/ip6_output.c:951
Read of size 8 at addr ffff88801d403e80 by task syz-executor.3/7618

CPU: 1 PID: 7618 Comm: syz-executor.3 Not tainted 6.1.0-rc6-syzkaller-00012-g4312098baf37 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 10/26/2022
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd1/0x138 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:284 [inline]
print_report+0x15e/0x45d mm/kasan/report.c:395
kasan_report+0xbf/0x1f0 mm/kasan/report.c:495
ip6_dst_idev include/net/ip6_fib.h:245 [inline]
ip6_fragment+0x2724/0x2770 net/ipv6/ip6_output.c:951
__ip6_finish_output net/ipv6/ip6_output.c:193 [inline]
ip6_finish_output+0x9a3/0x1170 net/ipv6/ip6_output.c:206
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip6_output+0x1f1/0x540 net/ipv6/ip6_output.c:227
dst_output include/net/dst.h:445 [inline]
ip6_local_out+0xb3/0x1a0 net/ipv6/output_core.c:161
ip6_send_skb+0xbb/0x340 net/ipv6/ip6_output.c:1966
udp_v6_send_skb+0x82a/0x18a0 net/ipv6/udp.c:1286
udp_v6_push_pending_frames+0x140/0x200 net/ipv6/udp.c:1313
udpv6_sendmsg+0x18da/0x2c80 net/ipv6/udp.c:1606
inet6_sendmsg+0x9d/0xe0 net/ipv6/af_inet6.c:665
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xd3/0x120 net/socket.c:734
sock_write_iter+0x295/0x3d0 net/socket.c:1108
call_write_iter include/linux/fs.h:2191 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9ed/0xdd0 fs/read_write.c:584
ksys_write+0x1ec/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x7fde3588c0d9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 f1 19 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fde365b6168 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 00007fde359ac050 RCX: 00007fde3588c0d9
RDX: 000000000000ffdc RSI: 00000000200000c0 RDI: 000000000000000a
RBP: 00007fde358e7ae9 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 00007fde35acfb1f R14: 00007fde365b6300 R15: 0000000000022000
</TASK>

Allocated by task 7618:
kasan_save_stack+0x22/0x40 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
__kasan_slab_alloc+0x82/0x90 mm/kasan/common.c:325
kasan_slab_alloc include/linux/kasan.h:201 [inline]
slab_post_alloc_hook mm/slab.h:737 [inline]
slab_alloc_node mm/slub.c:3398 [inline]
slab_alloc mm/slub.c:3406 [inline]
__kmem_cache_alloc_lru mm/slub.c:3413 [inline]
kmem_cache_alloc+0x2b4/0x3d0 mm/slub.c:3422
dst_alloc+0x14a/0x1f0 net/core/dst.c:92
ip6_dst_alloc+0x32/0xa0 net/ipv6/route.c:344
ip6_rt_pcpu_alloc net/ipv6/route.c:1369 [inline]
rt6_make_pcpu_route net/ipv6/route.c:1417 [inline]
ip6_pol_route+0x901/0x1190 net/ipv6/route.c:2254
pol_lookup_func include/net/ip6_fib.h:582 [inline]
fib6_rule_lookup+0x52e/0x6f0 net/ipv6/fib6_rules.c:121
ip6_route_output_flags_noref+0x2e6/0x380 net/ipv6/route.c:2625
ip6_route_output_flags+0x76/0x320 net/ipv6/route.c:2638
ip6_route_output include/net/ip6_route.h:98 [inline]
ip6_dst_lookup_tail+0x5ab/0x1620 net/ipv6/ip6_output.c:1092
ip6_dst_lookup_flow+0x90/0x1d0 net/ipv6/ip6_output.c:1222
ip6_sk_dst_lookup_flow+0x553/0x980 net/ipv6/ip6_output.c:1260
udpv6_sendmsg+0x151d/0x2c80 net/ipv6/udp.c:1554
inet6_sendmsg+0x9d/0xe0 net/ipv6/af_inet6.c:665
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xd3/0x120 net/socket.c:734
__sys_sendto+0x23a/0x340 net/socket.c:2117
__do_sys_sendto net/socket.c:2129 [inline]
__se_sys_sendto net/socket.c:2125 [inline]
__x64_sys_sendto+0xe1/0x1b0 net/socket.c:2125
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

Freed by task 7599:
kasan_save_stack+0x22/0x40 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2e/0x40 mm/kasan/generic.c:511
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free+0x160/0x1c0 mm/kasan/common.c:200
kasan_slab_free include/linux/kasan.h:177 [inline]
slab_free_hook mm/slub.c:1724 [inline]
slab_free_freelist_hook+0x8b/0x1c0 mm/slub.c:1750
slab_free mm/slub.c:3661 [inline]
kmem_cache_free+0xee/0x5c0 mm/slub.c:3683
dst_destroy+0x2ea/0x400 net/core/dst.c:127
rcu_do_batch kernel/rcu/tree.c:2250 [inline]
rcu_core+0x81f/0x1980 kernel/rcu/tree.c:2510
__do_softirq+0x1fb/0xadc kernel/softirq.c:571

Last potentially related work creation:
kasan_save_stack+0x22/0x40 mm/kasan/common.c:45
__kasan_record_aux_stack+0xbc/0xd0 mm/kasan/generic.c:481
call_rcu+0x9d/0x820 kernel/rcu/tree.c:2798
dst_release net/core/dst.c:177 [inline]
dst_release+0x7d/0xe0 net/core/dst.c:167
refdst_drop include/net/dst.h:256 [inline]
skb_dst_drop include/net/dst.h:268 [inline]
skb_release_head_state+0x250/0x2a0 net/core/skbuff.c:838
skb_release_all net/core/skbuff.c:852 [inline]
__kfree_skb net/core/skbuff.c:868 [inline]
kfree_skb_reason+0x151/0x4b0 net/core/skbuff.c:891
kfree_skb_list_reason+0x4b/0x70 net/core/skbuff.c:901
kfree_skb_list include/linux/skbuff.h:1227 [inline]
ip6_fragment+0x2026/0x2770 net/ipv6/ip6_output.c:949
__ip6_finish_output net/ipv6/ip6_output.c:193 [inline]
ip6_finish_output+0x9a3/0x1170 net/ipv6/ip6_output.c:206
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip6_output+0x1f1/0x540 net/ipv6/ip6_output.c:227
dst_output include/net/dst.h:445 [inline]
ip6_local_out+0xb3/0x1a0 net/ipv6/output_core.c:161
ip6_send_skb+0xbb/0x340 net/ipv6/ip6_output.c:1966
udp_v6_send_skb+0x82a/0x18a0 net/ipv6/udp.c:1286
udp_v6_push_pending_frames+0x140/0x200 net/ipv6/udp.c:1313
udpv6_sendmsg+0x18da/0x2c80 net/ipv6/udp.c:1606
inet6_sendmsg+0x9d/0xe0 net/ipv6/af_inet6.c:665
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xd3/0x120 net/socket.c:734
sock_write_iter+0x295/0x3d0 net/socket.c:1108
call_write_iter include/linux/fs.h:2191 [inline]
new_sync_write fs/read_write.c:491 [inline]
vfs_write+0x9ed/0xdd0 fs/read_write.c:584
ksys_write+0x1ec/0x250 fs/read_write.c:637
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

Second to last potentially related work creation:
kasan_save_stack+0x22/0x40 mm/kasan/common.c:45
__kasan_record_aux_stack+0xbc/0xd0 mm/kasan/generic.c:481
call_rcu+0x9d/0x820 kernel/rcu/tree.c:2798
dst_release net/core/dst.c:177 [inline]
dst_release+0x7d/0xe0 net/core/dst.c:167
refdst_drop include/net/dst.h:256 [inline]
skb_dst_drop include/net/dst.h:268 [inline]
__dev_queue_xmit+0x1b9d/0x3ba0 net/core/dev.c:4211
dev_queue_xmit include/linux/netdevice.h:3008 [inline]
neigh_resolve_output net/core/neighbour.c:1552 [inline]
neigh_resolve_output+0x51b/0x840 net/core/neighbour.c:1532
neigh_output include/net/neighbour.h:546 [inline]
ip6_finish_output2+0x56c/0x1530 net/ipv6/ip6_output.c:134
__ip6_finish_output net/ipv6/ip6_output.c:195 [inline]
ip6_finish_output+0x694/0x1170 net/ipv6/ip6_output.c:206
NF_HOOK_COND include/linux/netfilter.h:291 [inline]
ip6_output+0x1f1/0x540 net/ipv6/ip6_output.c:227
dst_output include/net/dst.h:445 [inline]
NF_HOOK include/linux/netfilter.h:302 [inline]
NF_HOOK include/linux/netfilter.h:296 [inline]
mld_sendpack+0xa09/0xe70 net/ipv6/mcast.c:1820
mld_send_cr net/ipv6/mcast.c:2121 [inline]
mld_ifc_work+0x720/0xdc0 net/ipv6/mcast.c:2653
process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289
worker_thread+0x669/0x1090 kernel/workqueue.c:2436
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306

The buggy address belongs to the object at ffff88801d403dc0
which belongs to the cache ip6_dst_cache of size 240
The buggy address is located 192 bytes inside of
240-byte region [ffff88801d403dc0, ffff88801d403eb0)

The buggy address belongs to the physical page:
page:ffffea00007500c0 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x1d403
memcg:ffff888022f49c81
flags: 0xfff00000000200(slab|node=0|zone=1|lastcpupid=0x7ff)
raw: 00fff00000000200 ffffea0001ef6580 dead000000000002 ffff88814addf640
raw: 0000000000000000 00000000800c000c 00000001ffffffff ffff888022f49c81
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 0, migratetype Unmovable, gfp_mask 0x112a20(GFP_ATOMIC|__GFP_NOWARN|__GFP_NORETRY|__GFP_HARDWALL), pid 3719, tgid 3719 (kworker/0:6), ts 136223432244, free_ts 136222971441
prep_new_page mm/page_alloc.c:2539 [inline]
get_page_from_freelist+0x10b5/0x2d50 mm/page_alloc.c:4288
__alloc_pages+0x1cb/0x5b0 mm/page_alloc.c:5555
alloc_pages+0x1aa/0x270 mm/mempolicy.c:2285
alloc_slab_page mm/slub.c:1794 [inline]
allocate_slab+0x213/0x300 mm/slub.c:1939
new_slab mm/slub.c:1992 [inline]
___slab_alloc+0xa91/0x1400 mm/slub.c:3180
__slab_alloc.constprop.0+0x56/0xa0 mm/slub.c:3279
slab_alloc_node mm/slub.c:3364 [inline]
slab_alloc mm/slub.c:3406 [inline]
__kmem_cache_alloc_lru mm/slub.c:3413 [inline]
kmem_cache_alloc+0x31a/0x3d0 mm/slub.c:3422
dst_alloc+0x14a/0x1f0 net/core/dst.c:92
ip6_dst_alloc+0x32/0xa0 net/ipv6/route.c:344
icmp6_dst_alloc+0x71/0x680 net/ipv6/route.c:3261
mld_sendpack+0x5de/0xe70 net/ipv6/mcast.c:1809
mld_send_cr net/ipv6/mcast.c:2121 [inline]
mld_ifc_work+0x720/0xdc0 net/ipv6/mcast.c:2653
process_one_work+0x9bf/0x1710 kernel/workqueue.c:2289
worker_thread+0x669/0x1090 kernel/workqueue.c:2436
kthread+0x2e8/0x3a0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:306
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1459 [inline]
free_pcp_prepare+0x65c/0xd90 mm/page_alloc.c:1509
free_unref_page_prepare mm/page_alloc.c:3387 [inline]
free_unref_page+0x1d/0x4d0 mm/page_alloc.c:3483
__unfreeze_partials+0x17c/0x1a0 mm/slub.c:2586
qlink_free mm/kasan/quarantine.c:168 [inline]
qlist_free_all+0x6a/0x170 mm/kasan/quarantine.c:187
kasan_quarantine_reduce+0x184/0x210 mm/kasan/quarantine.c:294
__kasan_slab_alloc+0x66/0x90 mm/kasan/common.c:302
kasan_slab_alloc include/linux/kasan.h:201 [inline]
slab_post_alloc_hook mm/slab.h:737 [inline]
slab_alloc_node mm/slub.c:3398 [inline]
kmem_cache_alloc_node+0x304/0x410 mm/slub.c:3443
__alloc_skb+0x214/0x300 net/core/skbuff.c:497
alloc_skb include/linux/skbuff.h:1267 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1191 [inline]
netlink_sendmsg+0x9a6/0xe10 net/netlink/af_netlink.c:1896
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg+0xd3/0x120 net/socket.c:734
__sys_sendto+0x23a/0x340 net/socket.c:2117
__do_sys_sendto net/socket.c:2129 [inline]
__se_sys_sendto net/socket.c:2125 [inline]
__x64_sys_sendto+0xe1/0x1b0 net/socket.c:2125
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x39/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd

Fixes: 1758fd4688eb ("ipv6: remove unnecessary dst_hold() in ip6_fragment()")
Reported-by: syzbot+8c0ac31aa9681abb9e2d@syzkaller.appspotmail.com
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Cc: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/r/20221206101351.2037285-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: plip: don't call kfree_skb/dev_kfree_skb() under spin_lock_irq()

[ Upstream commit 7d8c19bfc8ff3f78e5337107ca9246327fcb6b45 ]

It is not allowed to call kfree_skb() or consume_skb() from
hardware interrupt context or with interrupts being disabled.
So replace kfree_skb/dev_kfree_skb() with dev_kfree_skb_irq()
and dev_consume_skb_irq() under spin_lock_irq().

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20221207015310.2984909-1-yangyingliang@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: mxl-gpy: fix version reporting

[ Upstream commit fc3dd0367e610ae20ebbce6c38c7b86c3a2cc07f ]

The commit 09ce6b20103b ("net: phy: mxl-gpy: add temperature sensor")
will overwrite the return value and the reported version will be wrong.
Fix it.

Fixes: 09ce6b20103b ("net: phy: mxl-gpy: add temperature sensor")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 5f4d487d01ff ("net: phy: mxl-gpy: add MDINT workaround")
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/netback: fix build warning

[ Upstream commit 7dfa764e0223a324366a2a1fc056d4d9d4e95491 ]

Commit ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in
the non-linear area") introduced a (valid) build warning. There have
even been reports of this problem breaking networking of Xen guests.

Fixes: ad7f402ae4f4 ("xen/netback: Ensure protocol headers don't fall in the non-linear area")
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Tested-by: Jason Andryuk <jandryuk@gmail.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dpaa2-switch: Fix memory leak in dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove()

[ Upstream commit 4fad22a1281c500f15b172c9d261eff347ca634b ]

The cmd_buff needs to be freed when error happened in
dpaa2_switch_acl_entry_add() and dpaa2_switch_acl_entry_remove().

Fixes: 1110318d83e8 ("dpaa2-switch: add tc flower hardware offload on ingress traffic")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221205061515.115012-1-yuancan@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ethernet: aeroflex: fix potential skb leak in greth_init_rings()

[ Upstream commit 063a932b64db3317ec020c94466fe52923a15f60 ]

The greth_init_rings() function won't free the newly allocated skb when
dma_mapping_error() returns error, so add dev_kfree_skb() to fix it.

Compile tested only.

Fixes: d4c41139df6e ("net: Add Aeroflex Gaisler 10/100/1G Ethernet MAC driver")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/1670134149-29516-1-git-send-email-zhangchangzhong@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tipc: call tipc_lxc_xmit without holding node_read_lock

[ Upstream commit 88956177db179e4eba7cd590971961857d1565b8 ]

When sending packets between nodes in netns, it calls tipc_lxc_xmit() for
peer node to receive the packets where tipc_sk_mcast_rcv()/tipc_sk_rcv()
might be called, and it's pretty much like in tipc_rcv().

Currently the local 'node rw lock' is held during calling tipc_lxc_xmit()
to protect the peer_net not being freed by another thread. However, when
receiving these packets, tipc_node_add_conn() might be called where the
peer 'node rw lock' is acquired. Then a dead lock warning is triggered by
lockdep detector, although it is not a real dead lock:

    WARNING: possible recursive locking detected
    --------------------------------------------
    conn_server/1086 is trying to acquire lock:
    ffff8880065cb020 (&n->lock#2){++--}-{2:2}, \
                     at: tipc_node_add_conn.cold.76+0xaa/0x211 [tipc]

    but task is already holding lock:
    ffff8880065cd020 (&n->lock#2){++--}-{2:2}, \
                     at: tipc_node_xmit+0x285/0xb30 [tipc]

    other info that might help us debug this:
     Possible unsafe locking scenario:

           CPU0
           ----
      lock(&n->lock#2);
      lock(&n->lock#2);

     *** DEADLOCK ***

     May be due to missing lock nesting notation

    4 locks held by conn_server/1086:
     #0: ffff8880036d1e40 (sk_lock-AF_TIPC){+.+.}-{0:0}, \
                          at: tipc_accept+0x9c0/0x10b0 [tipc]
     #1: ffff8880036d5f80 (sk_lock-AF_TIPC/1){+.+.}-{0:0}, \
                          at: tipc_accept+0x363/0x10b0 [tipc]
     #2: ffff8880065cd020 (&n->lock#2){++--}-{2:2}, \
                          at: tipc_node_xmit+0x285/0xb30 [tipc]
     #3: ffff888012e13370 (slock-AF_TIPC){+...}-{2:2}, \
                          at: tipc_sk_rcv+0x2da/0x1b40 [tipc]

    Call Trace:
     <TASK>
     dump_stack_lvl+0x44/0x5b
     __lock_acquire.cold.77+0x1f2/0x3d7
     lock_acquire+0x1d2/0x610
     _raw_write_lock_bh+0x38/0x80
     tipc_node_add_conn.cold.76+0xaa/0x211 [tipc]
     tipc_sk_finish_conn+0x21e/0x640 [tipc]
     tipc_sk_filter_rcv+0x147b/0x3030 [tipc]
     tipc_sk_rcv+0xbb4/0x1b40 [tipc]
     tipc_lxc_xmit+0x225/0x26b [tipc]
     tipc_node_xmit.cold.82+0x4a/0x102 [tipc]
     __tipc_sendstream+0x879/0xff0 [tipc]
     tipc_accept+0x966/0x10b0 [tipc]
     do_accept+0x37d/0x590

This patch avoids this warning by not holding the 'node rw lock' before
calling tipc_lxc_xmit(). As to protect the 'peer_net', rcu_read_lock()
should be enough, as in cleanup_net() when freeing the netns, it calls
synchronize_rcu() before the free is continued.

Also since tipc_lxc_xmit() is like the RX path in tipc_rcv(), it makes
sense to call it under rcu_read_lock(). Note that the right lock order
must be:

   rcu_read_lock();
   tipc_node_read_lock(n);
   tipc_node_read_unlock(n);
   tipc_lxc_xmit();
   rcu_read_unlock();

instead of:

   tipc_node_read_lock(n);
   rcu_read_lock();
   tipc_node_read_unlock(n);
   tipc_lxc_xmit();
   rcu_read_unlock();

and we have to call tipc_node_read_lock/unlock() twice in
tipc_node_xmit().

Fixes: f73b12812a3d ("tipc: improve throughput between nodes in netns")
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Link: https://lore.kernel.org/r/5bdd1f8fee9db695cfff4528a48c9b9d0523fb00.1670110641.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: sja1105: fix memory leak in sja1105_setup_devlink_regions()

[ Upstream commit 78a9ea43fc1a7c06a420b132d2d47cbf4344a5df ]

When dsa_devlink_region_create failed in sja1105_setup_devlink_regions(),
priv->regions is not released.

Fixes: bf425b82059e ("net: dsa: sja1105: expose static config as devlink region")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221205012132.2110979-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv4: Fix incorrect route flushing when table ID 0 is used

[ Upstream commit c0d999348e01df03e0a7f550351f3907fabbf611 ]

Cited commit added the table ID to the FIB info structure, but did not
properly initialize it when table ID 0 is used. This can lead to a route
in the default VRF with a preferred source address not being flushed
when the address is deleted.

Consider the following example:

# ip address add dev dummy1 192.0.2.1/28
# ip address add dev dummy1 192.0.2.17/28
# ip route add 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 100
# ip route add table 0 198.51.100.0/24 via 192.0.2.2 src 192.0.2.17 metric 200
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 100
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200

Both routes are installed in the default VRF, but they are using two
different FIB info structures. One with a metric of 100 and table ID of
254 (main) and one with a metric of 200 and table ID of 0. Therefore,
when the preferred source address is deleted from the default VRF,
the second route is not flushed:

# ip address del dev dummy1 192.0.2.17/28
# ip route show 198.51.100.0/24
198.51.100.0/24 via 192.0.2.2 dev dummy1 src 192.0.2.17 metric 200

Fix by storing a table ID of 254 instead of 0 in the route configuration
structure.

Add a test case that fails before the fix:

# ./fib_tests.sh -t ipv4_del_addr

IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Table ID 0
     TEST: Route removed in default VRF when source address deleted      [FAIL]

Tests passed:   8
Tests failed:   1

And passes after:

# ./fib_tests.sh -t ipv4_del_addr

IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Table ID 0
     TEST: Route removed in default VRF when source address deleted      [ OK ]

Tests passed:   9
Tests failed:   0

Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs")
Reported-by: Donald Sharp <sharpd@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv4: Fix incorrect route flushing when source address is deleted

[ Upstream commit f96a3d74554df537b6db5c99c27c80e7afadc8d1 ]

Cited commit added the table ID to the FIB info structure, but did not
prevent structures with different table IDs from being consolidated.
This can lead to routes being flushed from a VRF when an address is
deleted from a different VRF.

Fix by taking the table ID into account when looking for a matching FIB
info. This is already done for FIB info structures backed by a nexthop
object in fib_find_info_nh().

Add test cases that fail before the fix:

# ./fib_tests.sh -t ipv4_del_addr

IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [FAIL]
     TEST: Route in default VRF not removed                              [ OK ]
RTNETLINK answers: File exists
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [FAIL]

Tests passed:   6
Tests failed:   2

And pass after:

# ./fib_tests.sh -t ipv4_del_addr

IPv4 delete address route tests
     Regular FIB info
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]
     Identical FIB info with different table ID
     TEST: Route removed from VRF when source address deleted            [ OK ]
     TEST: Route in default VRF not removed                              [ OK ]
     TEST: Route removed in default VRF when source address deleted      [ OK ]
     TEST: Route in VRF is not removed by address delete                 [ OK ]

Tests passed:   8
Tests failed:   0

Fixes: 5a56a0b3a45d ("net: Don't delete routes in different VRFs")
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tipc: Fix potential OOB in tipc_link_proto_rcv()

[ Upstream commit 743117a997bbd4840e827295c07e59bcd7f7caa3 ]

Fix the potential risk of OOB if skb_linearize() fails in
tipc_link_proto_rcv().

Fixes: 5cbb28a4bf65 ("tipc: linearize arriving NAME_DISTR and LINK_PROTO buffers")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20221203094635.29024-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hisilicon: Fix potential use-after-free in hix5hd2_rx()

[ Upstream commit 433c07a13f59856e4585e89e86b7d4cc59348fab ]

The skb is delivered to napi_gro_receive() which may free it, after
calling this, dereferencing skb may trigger use-after-free.

Fixes: 57c5bc9ad7d7 ("net: hisilicon: add hix5hd2 mac driver")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://lore.kernel.org/r/20221203094240.1240211-2-liujian56@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mdio: fix unbalanced fwnode reference count in mdio_device_release()

[ Upstream commit cb37617687f2bfa5b675df7779f869147c9002bd ]

There is warning report about of_node refcount leak
while probing mdio device:

OF: ERROR: memory leak, expected refcount 1 instead of 2,
of_node_get()/of_node_put() unbalanced - destroy cset entry:
attach overlay node /spi/soc@0/mdio@710700c0/ethernet@4

In of_mdiobus_register_device(), we increase fwnode refcount
by fwnode_handle_get() before associating the of_node with
mdio device, but it has never been decreased in normal path.
Since that, in mdio_device_release(), it needs to call
fwnode_handle_put() in addition instead of calling kfree()
directly.

After above, just calling mdio_device_free() in the error handle
path of of_mdiobus_register_device() is enough to keep the
refcount balanced.

Fixes: a9049e0c513c ("mdio: Add support for mdio drivers.")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Reviewed-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20221203073441.3885317-1-zengheng4@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hisilicon: Fix potential use-after-free in hisi_femac_rx()

[ Upstream commit 4640177049549de1a43e9bc49265f0cdfce08cfd ]

The skb is delivered to napi_gro_receive() which may free it, after
calling this, dereferencing skb may trigger use-after-free.

Fixes: 542ae60af24f ("net: hisilicon: Add Fast Ethernet MAC driver")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Link: https://lore.kernel.org/r/20221203094240.1240211-1-liujian56@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: thunderx: Fix missing destroy_workqueue of nicvf_rx_mode_wq

[ Upstream commit 42330a32933fb42180c52022804dcf09f47a2f99 ]

The nicvf_probe() won't destroy workqueue when register_netdev()
failed. Add destroy_workqueue err handle case to fix this issue.

Fixes: 2ecbe4f4a027 ("net: thunderx: replace global nicvf_rx_mode_wq work queue for all VFs to private for each of them.")
Signed-off-by: Yongqiang Liu <liuyongqiang13@huawei.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Link: https://lore.kernel.org/r/20221203094125.602812-1-liuyongqiang13@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: microchip: sparx5: Fix missing destroy_workqueue of mact_queue

[ Upstream commit 7b8232bdb1789a257de3129a9bb08c69b93a17db ]

The mchp_sparx5_probe() won't destroy workqueue created by
create_singlethread_workqueue() in sparx5_start() when later
inits failed. Add destroy_workqueue in the cleanup_ports case,
also add it in mchp_sparx5_remove()

Fixes: b37a1bae742f ("net: sparx5: add mactable support")
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Link: https://lore.kernel.org/r/20221203070259.19560-1-linqiheng@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ip_gre: do not report erspan version on GRE interface

[ Upstream commit ee496694b9eea651ae1aa4c4667d886cdf74aa3b ]

Although the type I ERSPAN is based on the barebones IP + GRE
encapsulation and no extra ERSPAN header. Report erspan version on GRE
interface looks unreasonable. Fix this by separating the erspan and gre
fill info.

IPv6 GRE does not have this info as IPv6 only supports erspan version
1 and 2.

Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: f989d546a2d5 ("erspan: Add type I version 0 support.")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Link: https://lore.kernel.org/r/20221203032858.3130339-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: fix "snps,axi-config" node property parsing

[ Upstream commit 61d4f140943c47c1386ed89f7260e00418dfad9d ]

In dt-binding snps,dwmac.yaml, some properties under "snps,axi-config"
node are named without "axi_" prefix, but the driver expects the
prefix. Since the dt-binding has been there for a long time, we'd
better make driver match the binding for compatibility.

Fixes: afea03656add ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20221202161739.2203-1-jszhang@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio/rockchip: fix refcount leak in rockchip_gpiolib_register()

[ Upstream commit 63ff545af73f759d1bd04198af8ed8577fb739fc ]

The node returned by of_get_parent() with refcount incremented,
of_node_put() needs be called when finish using it. So add it in the
end of of_pinctrl_get().

Fixes: 936ee2675eee ("gpio/rockchip: add driver for rockchip gpio")
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme initialize core quirks before calling nvme_init_subsystem

[ Upstream commit 6f2d71524bcfdeb1fcbd22a4a92a5b7b161ab224 ]

A device might have a core quirk for NVME_QUIRK_IGNORE_DEV_SUBNQN
(such as Samsung X5) but it would still give a:

"missing or invalid SUBNQN field"

warning as core quirks are filled after calling nvme_init_subnqn. Fill
ctrl->quirks from struct core_quirks before calling nvme_init_subsystem
to fix this.

Tested on a Samsung X5.

Fixes: ab9e00cc72fa ("nvme: track subsystems")
Signed-off-by: Pankaj Raghav <p.raghav@samsung.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFC: nci: Bounds check struct nfc_target arrays

[ Upstream commit e329e71013c9b5a4535b099208493c7826ee4a64 ]

While running under CONFIG_FORTIFY_SOURCE=y, syzkaller reported:

memcpy: detected field-spanning write (size 129) of single field "target->sensf_res" at net/nfc/nci/ntf.c:260 (size 18)

This appears to be a legitimate lack of bounds checking in
nci_add_new_protocol(). Add the missing checks.

Reported-by: syzbot+210e196cef4711b65139@syzkaller.appspotmail.com
Link: https://lore.kernel.org/lkml/0000000000001c590f05ee7b3ff4@google.com
Fixes: 019c4fbaa790 ("NFC: Add NCI multiple targets support")
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221202214410.never.693-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Disallow ip4 and ip6 l4_4_bytes

[ Upstream commit d64aaf3f7869f915fd120763d75f11d6b116424d ]

Return -EOPNOTSUPP, when user requests l4_4_bytes for raw IP4 or
IP6 flow director filters. Flow director does not support filtering
on l4 bytes for PCTYPEs used by IP4 and IP6 filters.
Without this patch, user could create filters with l4_4_bytes fields,
which did not do any filtering on L4, but only on L3 fields.

Fixes: 36777d9fa24c ("i40e: check current configured input set when adding ntuple filters")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Fix for VF MAC address 0

[ Upstream commit 08501970472077ed5de346ad89943a37d1692e9b ]

After spawning max VFs on a PF, some VFs were not getting resources and
their MAC addresses were 0. This was caused by PF sleeping before flushing
HW registers which caused VIRTCHNL_VFR_VFACTIVE to not be set in time for
VF.

Fix by adding a sleep after hw flush.

Fixes: e4b433f4a741 ("i40e: reset all VFs in parallel when rebuilding PF")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: Fix not setting default xps_cpus after reset

[ Upstream commit 82e0572b23029b380464fa9fdc125db9c1506d0a ]

During tx rings configuration default XPS queue config is set and
__I40E_TX_XPS_INIT_DONE is locked. __I40E_TX_XPS_INIT_DONE state is
cleared and set again with default mapping only during queues build,
it means after first setup or reset with queues rebuild. (i.e.
ethtool -L <interface> combined <number>) After other resets (i.e.
ethtool -t <interface>) XPS_INIT_DONE is not cleared and those default
maps cannot be set again. It results in cleared xps_cpus mapping
until queues are not rebuild or mapping is not set by user.

Add clearing __I40E_TX_XPS_INIT_DONE state during reset to let
the driver set xps_cpus to defaults again after it was cleared.

Fixes: 6f853d4f8e93 ("i40e: allow XPS with QoS enabled")
Signed-off-by: Michal Jaron <michalx.jaron@intel.com>
Signed-off-by: Kamil Maziarz <kamil.maziarz@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mvneta: Prevent out of bounds read in mvneta_config_rss()

[ Upstream commit e8b4fc13900b8e8be48debffd0dfd391772501f7 ]

The pp->indir[0] value comes from the user. It is passed to:

if (cpu_online(pp->rxq_def))

inside the mvneta_percpu_elect() function. It needs bounds checkeding
to ensure that it is not beyond the end of the cpu bitmap.

Fixes: cad5d847a093 ("net: mvneta: Fix the CPU choice in mvneta_percpu_elect")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen-netfront: Fix NULL sring after live migration

[ Upstream commit d50b7914fae04d840ce36491d22133070b18cca9 ]

A NAPI is setup for each network sring to poll data to kernel
The sring with source host is destroyed before live migration and
new sring with target host is setup after live migration.
The NAPI for the old sring is not deleted until setup new sring
with target host after migration. With busy_poll/busy_read enabled,
the NAPI can be polled before got deleted when resume VM.

BUG: unable to handle kernel NULL pointer dereference at
0000000000000008
IP: xennet_poll+0xae/0xd20
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
Call Trace:
finish_task_switch+0x71/0x230
timerqueue_del+0x1d/0x40
hrtimer_try_to_cancel+0xb5/0x110
xennet_alloc_rx_buffers+0x2a0/0x2a0
napi_busy_loop+0xdb/0x270
sock_poll+0x87/0x90
do_sys_poll+0x26f/0x580
tracing_map_insert+0x1d4/0x2f0
event_hist_trigger+0x14a/0x260

finish_task_switch+0x71/0x230
__schedule+0x256/0x890
recalc_sigpending+0x1b/0x50
xen_sched_clock+0x15/0x20
__rb_reserve_next+0x12d/0x140
ring_buffer_lock_reserve+0x123/0x3d0
event_triggers_call+0x87/0xb0
trace_event_buffer_commit+0x1c4/0x210
xen_clocksource_get_cycles+0x15/0x20
ktime_get_ts64+0x51/0xf0
SyS_ppoll+0x160/0x1a0
SyS_ppoll+0x160/0x1a0
do_syscall_64+0x73/0x130
entry_SYSCALL_64_after_hwframe+0x41/0xa6
...
RIP: xennet_poll+0xae/0xd20 RSP: ffffb4f041933900
CR2: 0000000000000008
---[ end trace f8601785b354351c ]---

xen frontend should remove the NAPIs for the old srings before live
migration as the bond srings are destroyed

There is a tiny window between the srings are set to NULL and
the NAPIs are disabled, It is safe as the NAPI threads are still
frozen at that time

Signed-off-by: Lin Liu <lin.liu@citrix.com>
Fixes: 4ec2411980d0 ([NET]: Do not check netif_running() and carrier state in ->poll())
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-pf: Fix potential memory leak in otx2_init_tc()

[ Upstream commit fbf33f5ac76f2cdb47ad9763f620026d5cfa57ce ]

In otx2_init_tc(), if rhashtable_init() failed, it does not free
tc->tc_entries_bitmap which is allocated in otx2_tc_alloc_ent_bitmap().

Fixes: 2e2a8126ffac ("octeontx2-pf: Unify flow management variables")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mdiobus: fix double put fwnode in the error path

[ Upstream commit 165df24186ecea95705505627df3dacf5e7ff6bf ]

If phy_device_register() or fwnode_mdiobus_phy_device_register()
fail, phy_device_free() is called, the device refcount is decreased
to 0, then fwnode_handle_put() will be called in phy_device_release(),
but in the error path, fwnode_handle_put() has already been called,
so set fwnode to NULL after fwnode_handle_put() in the error path to
avoid double put.

Fixes: cdde1560118f ("net: mdiobus: fix unbalanced node reference count")
Reported-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Zeng Heng <zengheng4@huawei.com>
Tested-by: Zeng Heng <zengheng4@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mdiobus: fwnode_mdiobus_register_phy() rework error handling

[ Upstream commit cfaa202a73eafaf91a3d0a86b5e5df006562f5c0 ]

Rework error handling as preparation for PSE patch. This patch should
make it easier to extend this function.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 165df24186ec ("net: mdiobus: fix double put fwnode in the error path")
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: encx24j600: Fix invalid logic in reading of MISTAT register

[ Upstream commit 25f427ac7b8d89b0259f86c0c6407b329df742b2 ]

A loop for reading MISTAT register continues while regmap_read() fails
and (mistat & BUSY), but if regmap_read() fails a value of mistat is
undefined.

The patch proposes to check for BUSY flag only when regmap_read()
succeed. Compile test only.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: d70e53262f5c ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: encx24j600: Add parentheses to fix precedence

[ Upstream commit 167b3f2dcc62c271f3555b33df17e361bb1fa0ee ]

In functions regmap_encx24j600_phy_reg_read() and
regmap_encx24j600_phy_reg_write() in the conditions of the waiting
cycles for filling the variable 'ret' it is necessary to add parentheses
to prevent wrong assignment due to logical operations precedence.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: d70e53262f5c ("net: Microchip encx24j600 driver")
Signed-off-by: Valentina Goncharenko <goncharenko.vp@ispras.ru>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mac802154: fix missing INIT_LIST_HEAD in ieee802154_if_add()

[ Upstream commit b3d72d3135d2ef68296c1ee174436efd65386f04 ]

Kernel fault injection test reports null-ptr-deref as follows:

BUG: kernel NULL pointer dereference, address: 0000000000000008
RIP: 0010:cfg802154_netdev_notifier_call+0x120/0x310 include/linux/list.h:114
Call Trace:
<TASK>
raw_notifier_call_chain+0x6d/0xa0 kernel/notifier.c:87
call_netdevice_notifiers_info+0x6e/0xc0 net/core/dev.c:1944
unregister_netdevice_many_notify+0x60d/0xcb0 net/core/dev.c:1982
unregister_netdevice_queue+0x154/0x1a0 net/core/dev.c:10879
register_netdevice+0x9a8/0xb90 net/core/dev.c:10083
ieee802154_if_add+0x6ed/0x7e0 net/mac802154/iface.c:659
ieee802154_register_hw+0x29c/0x330 net/mac802154/main.c:229
mcr20a_probe+0xaaa/0xcb1 drivers/net/ieee802154/mcr20a.c:1316

ieee802154_if_add() allocates wpan_dev as netdev's private data, but not
init the list in struct wpan_dev. cfg802154_netdev_notifier_call() manage
the list when device register/unregister, and may lead to null-ptr-deref.

Use INIT_LIST_HEAD() on it to initialize it correctly.

Fixes: fcf39e6e88e9 ("ieee802154: add wpan_dev_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Alexander Aring <aahringo@redhat.com>
Link: https://lore.kernel.org/r/20221130091705.1831140-1-weiyongjun@huaweicloud.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selftests: rtnetlink: correct xfrm policy rule in kci_test_ipsec_offload

[ Upstream commit 85a0506c073332a3057f5a9635fa0d4db5a8e03b ]

When testing in kci_test_ipsec_offload, srcip is configured as $dstip,
it should add xfrm policy rule in instead of out.
The test result of this patch is as follows:
PASS: ipsec_offload

Fixes: 2766a11161cc ("selftests: rtnetlink: add ipsec offload API test")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Acked-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20221201082246.14131-1-shaozhengchao@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: sja1105: Check return value

[ Upstream commit 8948876335b1752176afdff8e704099a3ea0f6e6 ]

Return NULL if we got unexpected value from skb_trim_rcsum() in
sja1110_rcv_inband_control_extension()

Fixes: 4913b8ebf8a9 ("net: dsa: add support for the SJA1110 native tagging protocol")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221201140032.26746-3-artem.chernyshev@red-soft.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: hellcreek: Check return value

[ Upstream commit d4edb50688652eb10be270bc515da63815de428f ]

Return NULL if we got unexpected value from skb_trim_rcsum()
in hellcreek_rcv()

Fixes: 01ef09caad66 ("net: dsa: Add tag handling for Hirschmann Hellcreek switches")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20221201140032.26746-2-artem.chernyshev@red-soft.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: dsa: ksz: Check return value

[ Upstream commit 3d8fdcbf1f42e2bb9ae8b8c0b6f202278c788a22 ]

Return NULL if we got unexpected value from skb_trim_rcsum()
in ksz_common_rcv()

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: bafe9ba7d908 ("net: dsa: ksz: Factor out common tag code")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20221201140032.26746-1-artem.chernyshev@red-soft.ru
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Fix not cleanup led when bt_init fails

[ Upstream commit 2f3957c7eb4e07df944169a3e50a4d6790e1c744 ]

bt_init() calls bt_leds_init() to register led, but if it fails later,
bt_leds_cleanup() is not called to unregister it.

This can cause panic if the argument "bluetooth-power" in text is freed
and then another led_trigger_register() tries to access it:

BUG: unable to handle page fault for address: ffffffffc06d3bc0
RIP: 0010:strcmp+0xc/0x30
  Call Trace:
    <TASK>
    led_trigger_register+0x10d/0x4f0
    led_trigger_register_simple+0x7d/0x100
    bt_init+0x39/0xf7 [bluetooth]
    do_one_initcall+0xd0/0x4e0

Fixes: e64c97b53bc6 ("Bluetooth: Add combined LED trigger for controller power")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: 6LoWPAN: add missing hci_dev_put() in get_l2cap_conn()

[ Upstream commit 747da1308bdd5021409974f9180f0d8ece53d142 ]

hci_get_route() takes reference, we should use hci_dev_put() to release
it when not need anymore.

Fixes: 6b8d4a6a0314 ("Bluetooth: 6LoWPAN: Use connected oriented channel instead of fixed one")
Signed-off-by: Wang ShaoBo <bobo.shaobowang@huawei.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vmxnet3: use correct intrConf reference when using extended queues

[ Upstream commit 409e8ec8c5825591895937b8499b54aa2476fae7 ]

Commit 39f9895a00f4 ("vmxnet3: add support for 32 Tx/Rx queues")
added support for 32Tx/Rx queues. As a part of this patch, intrConf
structure was extended to incorporate increased queues.

This patch fixes the issue where incorrect reference is being used.

Fixes: 39f9895a00f4 ("vmxnet3: add support for 32 Tx/Rx queues")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

vmxnet3: correctly report encapsulated LRO packet

[ Upstream commit 40b8c2a1af03ba3e8da55a4490d646bfa845e71a ]

Commit dacce2be3312 ("vmxnet3: add geneve and vxlan tunnel offload
support") added support for encapsulation offload. However, the
pathc did not report correctly the encapsulated packet which is
LRO'ed by the hypervisor.

This patch fixes this issue by using correct callback for the LRO'ed
encapsulated packet.

Fixes: dacce2be3312 ("vmxnet3: add geneve and vxlan tunnel offload support")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Acked-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

af_unix: Get user_ns from in_skb in unix_diag_get_exact().

[ Upstream commit b3abe42e94900bdd045c472f9c9be620ba5ce553 ]

Wei Chen reported a NULL deref in sk_user_ns() [0][1], and Paolo diagnosed
the root cause: in unix_diag_get_exact(), the newly allocated skb does not
have sk. [2]

We must get the user_ns from the NETLINK_CB(in_skb).sk and pass it to
sk_diag_fill().

[0]:
BUG: kernel NULL pointer dereference, address: 0000000000000270
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 12bbce067 P4D 12bbce067 PUD 12bc40067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
CPU: 0 PID: 27942 Comm: syz-executor.0 Not tainted 6.1.0-rc5-next-20221118 #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.13.0-48-gd9c812dda519-prebuilt.qemu.org 04/01/2014
RIP: 0010:sk_user_ns include/net/sock.h:920 [inline]
RIP: 0010:sk_diag_dump_uid net/unix/diag.c:119 [inline]
RIP: 0010:sk_diag_fill+0x77d/0x890 net/unix/diag.c:170
Code: 89 ef e8 66 d4 2d fd c7 44 24 40 00 00 00 00 49 8d 7c 24 18 e8
54 d7 2d fd 49 8b 5c 24 18 48 8d bb 70 02 00 00 e8 43 d7 2d fd <48> 8b
9b 70 02 00 00 48 8d 7b 10 e8 33 d7 2d fd 48 8b 5b 10 48 8d
RSP: 0018:ffffc90000d67968 EFLAGS: 00010246
RAX: ffff88812badaa48 RBX: 0000000000000000 RCX: ffffffff840d481d
RDX: 0000000000000465 RSI: 0000000000000000 RDI: 0000000000000270
RBP: ffffc90000d679a8 R08: 0000000000000277 R09: 0000000000000000
R10: 0001ffffffffffff R11: 0001c90000d679a8 R12: ffff88812ac03800
R13: ffff88812c87c400 R14: ffff88812ae42210 R15: ffff888103026940
FS: 00007f08b4e6f700(0000) GS:ffff88813bc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000270 CR3: 000000012c58b000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
unix_diag_get_exact net/unix/diag.c:285 [inline]
unix_diag_handler_dump+0x3f9/0x500 net/unix/diag.c:317
__sock_diag_cmd net/core/sock_diag.c:235 [inline]
sock_diag_rcv_msg+0x237/0x250 net/core/sock_diag.c:266
netlink_rcv_skb+0x13e/0x250 net/netlink/af_netlink.c:2564
sock_diag_rcv+0x24/0x40 net/core/sock_diag.c:277
netlink_unicast_kernel net/netlink/af_netlink.c:1330 [inline]
netlink_unicast+0x5e9/0x6b0 net/netlink/af_netlink.c:1356
netlink_sendmsg+0x739/0x860 net/netlink/af_netlink.c:1932
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
____sys_sendmsg+0x38f/0x500 net/socket.c:2476
___sys_sendmsg net/socket.c:2530 [inline]
__sys_sendmsg+0x197/0x230 net/socket.c:2559
__do_sys_sendmsg net/socket.c:2568 [inline]
__se_sys_sendmsg net/socket.c:2566 [inline]
__x64_sys_sendmsg+0x42/0x50 net/socket.c:2566
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x2b/0x70 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
RIP: 0033:0x4697f9
Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48
89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d
01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f08b4e6ec48 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 000000000077bf80 RCX: 00000000004697f9
RDX: 0000000000000000 RSI: 00000000200001c0 RDI: 0000000000000003
RBP: 00000000004d29e9 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000000000077bf80
R13: 0000000000000000 R14: 000000000077bf80 R15: 00007ffdb36bc6c0
</TASK>
Modules linked in:
CR2: 0000000000000270

[1]: https://lore.kernel.org/netdev/CAO4mrfdvyjFpokhNsiwZiP-wpdSD0AStcJwfKcKQdAALQ9_2Qw@mail.gmail.com/
[2]: https://lore.kernel.org/netdev/e04315e7c90d9a75613f3993c2baf2d344eef7eb.camel@redhat.com/

Fixes: cae9910e7344 ("net: Add UNIX_DIAG_UID to Netlink UNIX socket diagnostics.")
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: Wei Chen <harperchen1110@gmail.com>
Diagnosed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm: bridge: dw_hdmi: fix preference of RGB modes over YUV420

[ Upstream commit d3d6b1bf85aefe0ebc0624574b3bb62f0693914c ]

Cheap monitors sometimes advertise YUV modes they don't really have
(HDMI specification mandates YUV support so even monitors without actual
support will often wrongfully advertise it) which results in YUV matches
and user forum complaints of a red tint to light colour display areas in
common desktop environments.

Moving the default RGB fall-back before YUV selection results in RGB
mode matching in most cases, reducing complaints.

Fixes: 6c3c719936da ("drm/bridge: synopsys: dw-hdmi: add bus format negociation")
Signed-off-by: Guillaume BRUN <the.cheaterman@gmail.com>
Tested-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221116143523.2126-1-the.cheaterman@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: broadcom: Add PTP_1588_CLOCK_OPTIONAL dependency for BCMGENET under ARCH_BCM2835

[ Upstream commit 421f8663b3a775c32f724f793264097c60028f2e ]

commit 8d820bc9d12b ("net: broadcom: Fix BCMGENET Kconfig") fixes the build
that contain 99addbe31f55 ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
and enable BCMGENET=y but PTP_1588_CLOCK_OPTIONAL=m, which otherwise
leads to a link failure. However this may trigger a runtime failure.

Fix the original issue by propagating the PTP_1588_CLOCK_OPTIONAL dependency
of BROADCOM_PHY down to BCMGENET.

Fixes: 8d820bc9d12b ("net: broadcom: Fix BCMGENET Kconfig")
Fixes: 99addbe31f55 ("net: broadcom: Select BROADCOM_PHY for BCMGENET")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20221125115003.30308-1-yuehaibing@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

igb: Allocate MSI-X vector when testing

[ Upstream commit 28e96556baca7056d11d9fb3cdd0aba4483e00d8 ]

Without this change, the interrupt test fail with MSI-X environment:

$ sudo ethtool -t enp0s2 offline
[   43.921783] igb 0000:00:02.0: offline testing starting
[   44.855824] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Down
[   44.961249] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[   51.272202] igb 0000:00:02.0: testing shared interrupt
[   56.996975] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is FAIL
The test extra info:
Register test  (offline) 0
Eeprom test    (offline) 0
Interrupt test (offline) 4
Loopback test  (offline) 0
Link test   (on/offline) 0

Here, "4" means an expected interrupt was not delivered.

To fix this, route IRQs correctly to the first MSI-X vector by setting
IVAR_MISC. Also, set bit 0 of EIMS so that the vector will not be
masked. The interrupt test now runs properly with this change:

$ sudo ethtool -t enp0s2 offline
[   42.762985] igb 0000:00:02.0: offline testing starting
[   50.141967] igb 0000:00:02.0: testing shared interrupt
[   56.163957] igb 0000:00:02.0 enp0s2: igb: enp0s2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
The test result is PASS
The test extra info:
Register test  (offline) 0
Eeprom test    (offline) 0
Interrupt test (offline) 0
Loopback test  (offline) 0
Link test   (on/offline) 0

Fixes: 4eefa8f01314 ("igb: add single vector msi-x testing to interrupt test")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

e1000e: Fix TX dispatch condition

[ Upstream commit eed913f6919e253f35d454b2f115f2a4db2b741a ]

e1000_xmit_frame is expected to stop the queue and dispatch frames to
hardware if there is not sufficient space for the next frame in the
buffer, but sometimes it failed to do so because the estimated maximum
size of frame was wrong. As the consequence, the later invocation of
e1000_xmit_frame failed with NETDEV_TX_BUSY, and the frame in the buffer
remained forever, resulting in a watchdog failure.

This change fixes the estimated size by making it match with the
condition for NETDEV_TX_BUSY. Apparently, the old estimation failed to
account for the following lines which determines the space requirement
for not causing NETDEV_TX_BUSY:
    ```
     /* reserve a descriptor for the offload context */
     if ((mss) || (skb->ip_summed == CHECKSUM_PARTIAL))
     count++;
     count++;

     count += DIV_ROUND_UP(len, adapter->tx_fifo_limit);
    ```

This issue was found when running http-stress02 test included in Linux
Test Project 20220930 on QEMU with the following commandline:
```
qemu-system-x86_64 -M q35,accel=kvm -m 8G -smp 8
-drive if=virtio,format=raw,file=root.img,file.locking=on
-device e1000e,netdev=netdev
-netdev tap,script=ifup,downscript=no,id=netdev
```

Fixes: bc7f75fa9788 ("[E1000E]: New pci-express e1000 driver (currently for ICH9 devices only)")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: amd8111: Fix PCI device reference count leak

[ Upstream commit 45fecdb9f658d9c82960c98240bc0770ade19aca ]

for_each_pci_dev() is implemented by pci_get_device(). The comment of
pci_get_device() says that it will increase the reference count for the
returned pci_dev and also decrease the reference count for the input
pci_dev @from if it is not NULL.

If we break for_each_pci_dev() loop with pdev not NULL, we need to call
pci_dev_put() to decrease the reference count. Add the missing
pci_dev_put() after the 'out' label. Since pci_dev_put() can handle NULL
input parameter, there is no problem for the 'Device not found' branch.
For the normal path, add pci_dev_put() in amd_gpio_exit().

Fixes: f942a7de047d ("gpio: add a driver for GPIO pins found on AMD-8111 south bridge chips")
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/bridge: ti-sn65dsi86: Fix output polarity setting bug

[ Upstream commit 8c115864501fc09932cdfec53d9ec1cde82b4a28 ]

According to the description in ti-sn65dsi86's datasheet:

CHA_HSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.

CHA_VSYNC_POLARITY:
0 = Active High Pulse. Synchronization signal is high for the sync
pulse width. (Default)
1 = Active Low Pulse. Synchronization signal is low for the sync
pulse width.

We should only set these bits when the polarity is negative.

Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Qiqi Zhang <eddy.zhang@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125104558.84616-1-eddy.zhang@rock-chips.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ctnetlink: fix compilation warning after data race fixes in ct mark

[ Upstream commit 1feeae071507ad65cf9f462a1bdd543a4bf89e71 ]

All warnings (new ones prefixed by >>):

   net/netfilter/nf_conntrack_netlink.c: In function '__ctnetlink_glue_build':
>> net/netfilter/nf_conntrack_netlink.c:2674:13: warning: unused variable 'mark' [-Wunused-variable]
    2674 |         u32 mark;
         |             ^~~~

Fixes: 52d1aa8b8249 ("netfilter: conntrack: Fix data-races around ct mark")
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Ivan Babrou <ivan@ivan.computer>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ca8210: Fix crash by zero initializing data

[ Upstream commit 1e24c54da257ab93cff5826be8a793b014a5dc9c ]

The struct cas_control embeds multiple generic SPI structures and we
have to make sure these structures are initialized to default values.
This driver does not set all attributes. When using kmalloc before some
attributes were not initialized and contained random data which caused
random crashes at bootup.

Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Link: https://lore.kernel.org/r/20221121002201.1339636-1-hauke@hauke-m.de
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ieee802154: cc2520: Fix error return code in cc2520_hw_init()

[ Upstream commit 4d002d6a2a00ac1c433899bd7625c6400a74cfba ]

In cc2520_hw_init(), if oscillator start failed, the error code
should be returned.

Fixes: 0da6bc8cc341 ("ieee802154: cc2520: adds driver for TI CC2520 radio")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20221120075046.2213633-1-william.xuanziyang@huawei.com
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/vmwgfx: Fix race issue calling pin_user_pages

[ Upstream commit ed14d225cc7c842f6d4d5a3009f71a44f5852d09 ]

pin_user_pages() is unsafe without protection of mmap_lock,
fix it by calling pin_user_pages_fast().

Fixes: 7a7a933edd6c ("drm/vmwgfx: Introduce VMware mks-guest-stats")
Signed-off-by: Dawei Li <set_pte_at@outlook.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/TYWP286MB23193621CB443E1E1959A00BCA3E9@TYWP286MB2319.JPNP286.PROD.OUTLOOK.COM
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nft_set_pipapo: Actually validate intervals in fields after the first one

[ Upstream commit 97d4d394b58777f7056ebba8ffdb4002d0563259 ]

Embarrassingly, nft_pipapo_insert() checked for interval validity in
the first field only.

The start_p and end_p pointers were reset to key data from the first
field at every iteration of the loop which was supposed to go over
the set fields.

Fixes: 3c4287f62044 ("nf_tables: Add set type for arbitrary concatenation of ranges")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: fix memory leak in gpiochip_setup_dev()

[ Upstream commit ec851b23084b3a0af8bf0f5e51d33a8d678bdc49 ]

Here is a backtrace report about memory leak detected in
gpiochip_setup_dev():

unreferenced object 0xffff88810b406400 (size 512):
  comm "python3", pid 1682, jiffies 4295346908 (age 24.090s)
  backtrace:
    kmalloc_trace
    device_add device_private_init at drivers/base/core.c:3361
(inlined by) device_add at drivers/base/core.c:3411
    cdev_device_add
    gpiolib_cdev_register
    gpiochip_setup_dev
    gpiochip_add_data_with_key

gcdev_register() & gcdev_unregister() would call device_add() &
device_del() (no matter CONFIG_GPIO_CDEV is enabled or not) to
register/unregister device.

However, if device_add() succeeds, some resource (like
struct device_private allocated by device_private_init())
is not released by device_del().

Therefore, after device_add() succeeds by gcdev_register(), it
needs to call put_device() to release resource in the error handle
path.

Here we move forward the register of release function, and let it
release every piece of resource by put_device() instead of kfree().

While at it, fix another subtle issue, i.e. when gc->ngpio is equal
to 0, we still call kcalloc() and, in case of further error, kfree()
on the ZERO_PTR pointer, which is not NULL. It's not a bug per se,
but rather waste of the resources and potentially wrong expectation
about contents of the gdev->descs variable.

Fixes: 159f3cd92f17 ("gpiolib: Defer gpio device setup until after gpiolib initialization")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: check the 'ngpios' property in core gpiolib code

[ Upstream commit 9dbd1ab20509e85cd3fac9479a00c59e83c08196 ]

Several drivers read the 'ngpios' device property on their own, but
since it's defined as a standard GPIO property in the device tree bindings
anyway, it's a good candidate for generalization. If the driver didn't
set its gc->ngpio, try to read the 'ngpios' property from the GPIO
device's firmware node before bailing out.

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b23084b ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: improve coding style for local variables

[ Upstream commit e5ab49cd3d6937b1818b80cb5eb09dc018ae0718 ]

Drop unneeded whitespaces and put the variables of the same type
together for consistency with the rest of the code.

Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Stable-dep-of: ec851b23084b ("gpiolib: fix memory leak in gpiochip_setup_dev()")
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: Fix pointer casting to prevent oops in devm_clk_release()

[ Upstream commit 8b3d743fc9e2542822826890b482afabf0e7522a ]

The release function is called with a pointer to the memory returned by
devres_alloc(). I was confused about that by the code before the
generalization that used a struct clk **ptr.

Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: abae8e57e49a ("clk: generalize devm_clk_get() a bit")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220620171815.114212-1-u.kleine-koenig@pengutronix.de
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

can: af_can: fix NULL pointer dereference in can_rcv_filter

commit 0acc442309a0a1b01bcdaa135e56e6398a49439c upstream.

Analogue to commit 8aa59e355949 ("can: af_can: fix NULL pointer
dereference in can_rx_register()") we need to check for a missing
initialization of ml_priv in the receive path of CAN frames.

Since commit 4e096a18867a ("net: introduce CAN specific pointer in the
struct net_device") the check for dev->type to be ARPHRD_CAN is not
sufficient anymore since bonding or tun netdevices claim to be CAN
devices but do not initialize ml_priv accordingly.

Fixes: 4e096a18867a ("net: introduce CAN specific pointer in the struct net_device")
Reported-by: syzbot+2d7f58292cb5b29eb5ad@syzkaller.appspotmail.com
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20221206201259.3028-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: ite: Enable QUIRK_TOUCHPAD_ON_OFF_REPORT on Acer Aspire Switch V 10

commit 9ad6645a9dce4d0e42daca6ebf32a154401c59d3 upstream.

The Acer Aspire Switch V 10 (SW5-017)'s keyboard-dock uses the same
ITE controller setup as other Acer Switch 2-in-1's.

This needs special handling for the wifi on/off toggle hotkey as well as
to properly report touchpad on/off keypresses.

Add the USB-ids for the SW5-017's keyboard-dock with a quirk setting of
QUIRK_TOUCHPAD_ON_OFF_REPORT to fix both issues.

Cc: Rudolf Polzer <rpolzer@google.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: core: fix shift-out-of-bounds in hid_report_raw_event

commit ec61b41918587be530398b0d1c9a0d16619397e5 upstream.

Syzbot reported shift-out-of-bounds in hid_report_raw_event.

microsoft 0003:045E:07DA.0001: hid_field_extract() called with n (128) >
32! (swapper/0)
======================================================================
UBSAN: shift-out-of-bounds in drivers/hid/hid-core.c:1323:20
shift exponent 127 is too large for 32-bit type 'int'
CPU: 0 PID: 0 Comm: swapper/0 Not tainted
6.1.0-rc4-syzkaller-00159-g4bbf3422df78 #0
Hardware name: Google Compute Engine/Google Compute Engine, BIOS
Google 10/26/2022
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0x1e3/0x2cb lib/dump_stack.c:106
ubsan_epilogue lib/ubsan.c:151 [inline]
__ubsan_handle_shift_out_of_bounds+0x3a6/0x420 lib/ubsan.c:322
snto32 drivers/hid/hid-core.c:1323 [inline]
hid_input_fetch_field drivers/hid/hid-core.c:1572 [inline]
hid_process_report drivers/hid/hid-core.c:1665 [inline]
hid_report_raw_event+0xd56/0x18b0 drivers/hid/hid-core.c:1998
hid_input_report+0x408/0x4f0 drivers/hid/hid-core.c:2066
hid_irq_in+0x459/0x690 drivers/hid/usbhid/hid-core.c:284
__usb_hcd_giveback_urb+0x369/0x530 drivers/usb/core/hcd.c:1671
dummy_timer+0x86b/0x3110 drivers/usb/gadget/udc/dummy_hcd.c:1988
call_timer_fn+0xf5/0x210 kernel/time/timer.c:1474
expire_timers kernel/time/timer.c:1519 [inline]
__run_timers+0x76a/0x980 kernel/time/timer.c:1790
run_timer_softirq+0x63/0xf0 kernel/time/timer.c:1803
__do_softirq+0x277/0x75b kernel/softirq.c:571
__irq_exit_rcu+0xec/0x170 kernel/softirq.c:650
irq_exit_rcu+0x5/0x20 kernel/softirq.c:662
sysvec_apic_timer_interrupt+0x91/0xb0 arch/x86/kernel/apic/apic.c:1107
======================================================================

If the size of the integer (unsigned n) is bigger than 32 in snto32(),
shift exponent will be too large for 32-bit type 'int', resulting in a
shift-out-of-bounds bug.
Fix this by adding a check on the size of the integer (unsigned n) in
snto32(). To add support for n greater than 32 bits, set n to 32, if n
is greater than 32.

Reported-by: syzbot+8b1641d2f14732407e23@syzkaller.appspotmail.com
Fixes: dde5845a529f ("[PATCH] Generic HID layer - code split")
Signed-off-by: ZhangPeng <zhangpeng362@huawei.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: hid-lg4ff: Add check for empty lbuf

commit d180b6496143cd360c5d5f58ae4b9a8229c1f344 upstream.

If an empty buf is received, lbuf is also empty. So lbuf is
accessed by index -1.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: f31a2de3fe36 ("HID: hid-lg4ff: Allow switching of Logitech gaming wheels between compatibility modes")
Signed-off-by: Anastasia Belova <abelova@astralinux.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: usbhid: Add ALWAYS_POLL quirk for some mice

commit f6d910a89a2391e5ce1f275d205023880a33d3f8 upstream.

Some additional USB mouse devices are needing ALWAYS_POLL quirk without
which they disconnect and reconnect every 60s.

Add below devices to the known quirk list.
CHERRY VID 0x046a, PID 0x000c
MICROSOFT VID 0x045e, PID 0x0783
PRIMAX VID 0x0461, PID 0x4e2a

Signed-off-by: Ankit Patel <anpatel@nvidia.com>
Signed-off-by: Haotien Hsu <haotienh@nvidia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: sja1105: avoid out of bounds access in sja1105_init_l2_policing()

commit f8bac7f9fdb0017b32157957ffffd490f95faa07 upstream.

The SJA1105 family has 45 L2 policing table entries
(SJA1105_MAX_L2_POLICING_COUNT) and SJA1110 has 110
(SJA1110_MAX_L2_POLICING_COUNT). Keeping the table structure but
accounting for the difference in port count (5 in SJA1105 vs 10 in
SJA1110) does not fully explain the difference. Rather, the SJA1110 also
has L2 ingress policers for multicast traffic. If a packet is classified
as multicast, it will be processed by the policer index 99 + SRCPORT.

The sja1105_init_l2_policing() function initializes all L2 policers such
that they don't interfere with normal packet reception by default. To have
a common code between SJA1105 and SJA1110, the index of the multicast
policer for the port is calculated because it's an index that is out of
bounds for SJA1105 but in bounds for SJA1110, and a bounds check is
performed.

The code fails to do the proper thing when determining what to do with the
multicast policer of port 0 on SJA1105 (ds->num_ports = 5). The "mcast"
index will be equal to 45, which is also equal to
table->ops->max_entry_count (SJA1105_MAX_L2_POLICING_COUNT). So it passes
through the check. But at the same time, SJA1105 doesn't have multicast
policers. So the code programs the SHARINDX field of an out-of-bounds
element in the L2 Policing table of the static config.

The comparison between index 45 and 45 entries should have determined the
code to not access this policer index on SJA1105, since its memory wasn't
even allocated.

With enough bad luck, the out-of-bounds write could even overwrite other
valid kernel data, but in this case, the issue was detected using KASAN.

Kernel log:

sja1105 spi5.0: Probed switch chip: SJA1105Q
==================================================================
BUG: KASAN: slab-out-of-bounds in sja1105_setup+0x1cbc/0x2340
Write of size 8 at addr ffffff880bd57708 by task kworker/u8:0/8
...
Workqueue: events_unbound deferred_probe_work_func
Call trace:
...
sja1105_setup+0x1cbc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...
Allocated by task 8:
...
sja1105_setup+0x1bcc/0x2340
dsa_register_switch+0x1284/0x18d0
sja1105_probe+0x748/0x840
...

Fixes: 38fbe91f2287 ("net: dsa: sja1105: configure the multicast policers, if present")
CC: stable@vger.kernel.org # 5.15+
Signed-off-by: Radu Nicolae Pirea (OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20221207132347.38698-1-radu-nicolae.pirea@oss.nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/shmem-helper: Avoid vm_open error paths

commit 09bf649a74573cb596e211418a4f8008f265c5a9 upstream.

vm_open() is not allowed to fail. Fortunately we are guaranteed that
the pages are already pinned, thanks to the initial mmap which is now
being cloned into a forked process, and only need to increment the
refcnt. So just increment it directly. Previously if a signal was
delivered at the wrong time to the forking process, the
mutex_lock_interruptible() could fail resulting in the pages_use_count
not being incremented.

Fixes: 2194a63a818d ("drm: Add library for shmem backed GEM objects")
Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221130185748.357410-3-robdclark@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/shmem-helper: Remove errant put in error path

commit 24013314be6ee4ee456114a671e9fa3461323de8 upstream.

drm_gem_shmem_mmap() doesn't own this reference, resulting in the GEM
object getting prematurely freed leading to a later use-after-free.

Link: https://syzkaller.appspot.com/bug?extid=c8ae65286134dd1b800d
Reported-by: syzbot+c8ae65286134dd1b800d@syzkaller.appspotmail.com
Fixes: 2194a63a818d ("drm: Add library for shmem backed GEM objects")
Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221130185748.357410-2-robdclark@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu/sdma_v4_0: turn off SDMA ring buffer in the s2idle suspend

commit bc21fe9a5844c5bc8f7ec319b11d2671a94eb867 upstream.

In the SDMA s0ix save process requires to turn off SDMA ring buffer for
avoiding the SDMA in-flight request, otherwise will suffer from SDMA page
fault which causes by page request from in-flight SDMA ring accessing at
SDMA restore phase.

Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2248
Cc: stable@vger.kernel.org # 6.0,5.15+
Fixes: f8f4e2a51834 ("drm/amdgpu: skipping SDMA hw_init and hw_fini for S0ix.")
Signed-off-by: Prike Liang <Prike.Liang@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Tested-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vmwgfx: Don't use screen objects when SEV is active

commit 6e90293618ed476d6b11f82ce724efbb9e9a071b upstream.

When SEV is enabled gmr's and mob's are explicitly disabled because
the encrypted system memory can not be used by the hypervisor.

The driver was disabling GMR's but the presentation code, which depends
on GMR's, wasn't honoring it which lead to black screen on hosts
with SEV enabled.

Make sure screen objects presentation is not used when guest memory
regions have been disabled to fix presentation on SEV enabled hosts.

Fixes: 3b0d6458c705 ("drm/vmwgfx: Refuse DMA operation when SEV encryption is active")
Cc: <stable@vger.kernel.org> # v5.7+
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reported-by: Nicholas Hunt <nhunt@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221201175341.491884-1-zack@kde.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: vsie: Fix the initialization of the epoch extension (epdx) field

commit 0dd4cdccdab3d74bd86b868768a7dca216bcce7e upstream.

We recently experienced some weird huge time jumps in nested guests when
rebooting them in certain cases. After adding some debug code to the epoch
handling in vsie.c (thanks to David Hildenbrand for the idea!), it was
obvious that the "epdx" field (the multi-epoch extension) did not get set
to 0xff in case the "epoch" field was negative.
Seems like the code misses to copy the value from the epdx field from
the guest to the shadow control block. By doing so, the weird time
jumps are gone in our scenarios.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=2140899
Fixes: 8fa1696ea781 ("KVM: s390: Multiple Epoch Facility support")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Acked-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Cc: stable@vger.kernel.org # 4.19+
Link: https://lore.kernel.org/r/20221123090833.292938-1-thuth@redhat.com
Message-Id: <20221123090833.292938-1-thuth@redhat.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: mana: Fix race on per-CQ variable napi work_done

commit 18010ff776fa42340efc428b3ea6d19b3e7c7b21 upstream.

After calling napi_complete_done(), the NAPIF_STATE_SCHED bit may be
cleared, and another CPU can start napi thread and access per-CQ variable,
cq->work_done. If the other thread (for example, from busy_poll) sets
it to a value >= budget, this thread will continue to run when it should
stop, and cause memory corruption and panic.

To fix this issue, save the per-CQ work_done variable in a local variable
before napi_complete_done(), so it won't be corrupted by a possible
concurrent thread after napi_complete_done().

Also, add a flag bit to advertise to the NIC firmware: the NAPI work_done
variable race is fixed, so the driver is able to reliably support features
like busy_poll.

Cc: stable@vger.kernel.org
Fixes: e1b5683ff62e ("net: mana: Move NAPI from EQ to CQ")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Link: https://lore.kernel.org/r/1670010190-28595-1-git-send-email-haiyangz@microsoft.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix crash when replugging CSR fake controllers

commit b5ca338751ad4783ec8d37b5d99c3e37b7813e59 upstream.

It seems fake CSR 5.0 clones can cause the suspend notifier to be
registered twice causing the following kernel panic:

[   71.986122] Call Trace:
[   71.986124]  <TASK>
[   71.986125]  blocking_notifier_chain_register+0x33/0x60
[   71.986130]  hci_register_dev+0x316/0x3d0 [bluetooth 99b5497ea3d09708fa1366c1dc03288bf3cca8da]
[   71.986154]  btusb_probe+0x979/0xd85 [btusb e1e0605a4f4c01984a4b9c8ac58c3666ae287477]
[   71.986159]  ? __pm_runtime_set_status+0x1a9/0x300
[   71.986162]  ? ktime_get_mono_fast_ns+0x3e/0x90
[   71.986167]  usb_probe_interface+0xe3/0x2b0
[   71.986171]  really_probe+0xdb/0x380
[   71.986174]  ? pm_runtime_barrier+0x54/0x90
[   71.986177]  __driver_probe_device+0x78/0x170
[   71.986180]  driver_probe_device+0x1f/0x90
[   71.986183]  __device_attach_driver+0x89/0x110
[   71.986186]  ? driver_allows_async_probing+0x70/0x70
[   71.986189]  bus_for_each_drv+0x8c/0xe0
[   71.986192]  __device_attach+0xb2/0x1e0
[   71.986195]  bus_probe_device+0x92/0xb0
[   71.986198]  device_add+0x422/0x9a0
[   71.986201]  ? sysfs_merge_group+0xd4/0x110
[   71.986205]  usb_set_configuration+0x57a/0x820
[   71.986208]  usb_generic_driver_probe+0x4f/0x70
[   71.986211]  usb_probe_device+0x3a/0x110
[   71.986213]  really_probe+0xdb/0x380
[   71.986216]  ? pm_runtime_barrier+0x54/0x90
[   71.986219]  __driver_probe_device+0x78/0x170
[   71.986221]  driver_probe_device+0x1f/0x90
[   71.986224]  __device_attach_driver+0x89/0x110
[   71.986227]  ? driver_allows_async_probing+0x70/0x70
[   71.986230]  bus_for_each_drv+0x8c/0xe0
[   71.986232]  __device_attach+0xb2/0x1e0
[   71.986235]  bus_probe_device+0x92/0xb0
[   71.986237]  device_add+0x422/0x9a0
[   71.986239]  ? _dev_info+0x7d/0x98
[   71.986242]  ? blake2s_update+0x4c/0xc0
[   71.986246]  usb_new_device.cold+0x148/0x36d
[   71.986250]  hub_event+0xa8a/0x1910
[   71.986255]  process_one_work+0x1c4/0x380
[   71.986259]  worker_thread+0x51/0x390
[   71.986262]  ? rescuer_thread+0x3b0/0x3b0
[   71.986264]  kthread+0xdb/0x110
[   71.986266]  ? kthread_complete_and_exit+0x20/0x20
[   71.986268]  ret_from_fork+0x1f/0x30
[   71.986273]  </TASK>
[   71.986274] ---[ end trace 0000000000000000 ]---
[   71.986284] btusb: probe of 2-1.6:1.0 failed with error -17

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216683
Cc: stable@vger.kernel.org
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Tested-by: Leonardo Eugênio <lelgenio@disroot.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: btusb: Add debug message for CSR controllers

commit 955aebd445e2b49622f2184b7abb82b05c060549 upstream.

The rationale of showing this is that it's potentially critical
information to diagnose and find more CSR compatibility bugs in the
future and it will save a lot of headaches.

Given that clones come from a wide array of vendors (some are actually
Barrot, some are something else) and these numbers are what let us find
differences between actual and fake ones, it will be immensely helpful
to scour the Internet looking for this pattern and building an actual
database to find correlations and improve the checks.

Cc: stable@vger.kernel.org
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ismael Ferreras Morezuelas <swyterzone@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/gup: fix gup_pud_range() for dax

commit fcd0ccd836ffad73d98a66f6fea7b16f735ea920 upstream.

For dax pud, pud_huge() returns true on x86. So the function works as long
as hugetlb is configured. However, dax doesn't depend on hugetlb.
Commit 414fd080d125 ("mm/gup: fix gup_pmd_range() for dax") fixed
devmap-backed huge PMDs, but missed devmap-backed huge PUDs. Fix this as
well.

This fixes the below kernel panic:

general protection fault, probably for non-canonical address 0x69e7c000cc478: 0000 [#1] SMP
< snip >
Call Trace:
<TASK>
get_user_pages_fast+0x1f/0x40
iov_iter_get_pages+0xc6/0x3b0
? mempool_alloc+0x5d/0x170
bio_iov_iter_get_pages+0x82/0x4e0
? bvec_alloc+0x91/0xc0
? bio_alloc_bioset+0x19a/0x2a0
blkdev_direct_IO+0x282/0x480
? __io_complete_rw_common+0xc0/0xc0
? filemap_range_has_page+0x82/0xc0
generic_file_direct_write+0x9d/0x1a0
? inode_update_time+0x24/0x30
__generic_file_write_iter+0xbd/0x1e0
blkdev_write_iter+0xb4/0x150
? io_import_iovec+0x8d/0x340
io_write+0xf9/0x300
io_issue_sqe+0x3c3/0x1d30
? sysvec_reschedule_ipi+0x6c/0x80
__io_queue_sqe+0x33/0x240
? fget+0x76/0xa0
io_submit_sqes+0xe6a/0x18d0
? __fget_light+0xd1/0x100
__x64_sys_io_uring_enter+0x199/0x880
? __context_tracking_enter+0x1f/0x70
? irqentry_exit_to_user_mode+0x24/0x30
? irqentry_exit+0x1d/0x30
? __context_tracking_exit+0xe/0x70
do_syscall_64+0x3b/0x90
entry_SYSCALL_64_after_hwframe+0x61/0xcb
RIP: 0033:0x7fc97c11a7be
< snip >
</TASK>
---[ end trace 48b2e0e67debcaeb ]---
RIP: 0010:internal_get_user_pages_fast+0x340/0x990
< snip >
Kernel panic - not syncing: Fatal exception
Kernel Offset: disabled

Link: https://lkml.kernel.org/r/1670392853-28252-1-git-send-email-ssengar@linux.microsoft.com
Fixes: 414fd080d125 ("mm/gup: fix gup_pmd_range() for dax")
Signed-off-by: John Starks <jostarks@microsoft.com>
Signed-off-by: Saurabh Sengar <ssengar@linux.microsoft.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: John Hubbard <jhubbard@nvidia.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memcg: fix possible use-after-free in memcg_write_event_control()

commit 4a7ba45b1a435e7097ca0f79a847d0949d0eb088 upstream.

memcg_write_event_control() accesses the dentry->d_name of the specified
control fd to route the write call.  As a cgroup interface file can't be
renamed, it's safe to access d_name as long as the specified file is a
regular cgroup file.  Also, as these cgroup interface files can't be
removed before the directory, it's safe to access the parent too.

Prior to 347c4a874710 ("memcg: remove cgroup_event->cft"), there was a
call to __file_cft() which verified that the specified file is a regular
cgroupfs file before further accesses.  The cftype pointer returned from
__file_cft() was no longer necessary and the commit inadvertently dropped
the file type check with it allowing any file to slip through.  With the
invarients broken, the d_name and parent accesses can now race against
renames and removals of arbitrary files and cause use-after-free's.

Fix the bug by resurrecting the file type check in __file_cft().  Now that
cgroupfs is implemented through kernfs, checking the file operations needs
to go through a layer of indirection.  Instead, let's check the superblock
and dentry type.

Link: https://lkml.kernel.org/r/Y5FRm/cfcKPGzWwl@slm.duckdns.org
Fixes: 347c4a874710 ("memcg: remove cgroup_event->cft")
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Jann Horn <jannh@google.com>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Shakeel Butt <shakeelb@google.com>
Cc: <stable@vger.kernel.org> [3.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: v4l2-dv-timings.c: fix too strict blanking sanity checks

commit 5eef2141776da02772c44ec406d6871a790761ee upstream.

Sanity checks were added to verify the v4l2_bt_timings blanking fields
in order to avoid integer overflows when userspace passes weird values.

But that assumed that userspace would correctly fill in the front porch,
backporch and sync values, but sometimes all you know is the total
blanking, which is then assigned to just one of these fields.

And that can fail with these checks.

So instead set a maximum for the total horizontal and vertical
blanking and check that each field remains below that.

That is still sufficient to avoid integer overflows, but it also
allows for more flexibility in how userspace fills in these fields.

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 4b6d66a45ed3 ("media: v4l2-dv-timings: add sanity checks for blanking values")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ARM: dts: imx7: Fix NAND controller size-cells"

commit ef19964da8a668c683f1d38274f6fb756e047945 upstream.

This reverts commit 753395ea1e45c724150070b5785900b6a44bd5fb.

It introduced a boot regression on colibri-imx7, and potentially any
other i.MX7 boards with MTD partition list generated into the fdt by
U-Boot.

While the commit we are reverting here is not obviously wrong, it fixes
only a dt binding checker warning that is non-functional, while it
introduces a boot regression and there is no obvious fix ready.

Fixes: 753395ea1e45 ("ARM: dts: imx7: Fix NAND controller size-cells")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Marek Vasut <marex@denx.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/all/Y4dgBTGNWpM6SQXI@francesco-nb.int.toradex.com/
Link: https://lore.kernel.org/all/20221205144917.6514168a@xps-13/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

soundwire: intel: Initialize clock stop timeout

commit 13c30a755847c7e804e1bf755e66e3ff7b7f9367 upstream.

The bus->clk_stop_timeout member is only initialized to a non-zero value
during the codec driver probe. This can lead to corner cases where this
value remains pegged at zero when the bus suspends, which results in an
endless loop in sdw_bus_wait_for_clk_prep_deprep().

Corner cases include configurations with no codecs described in the
firmware, or delays in probing codec drivers.

Initializing the default timeout to the smallest non-zero value avoid this
problem and allows for the existing logic to be preserved: the
bus->clk_stop_timeout is set as the maximum required by all codecs
connected on the bus.

Fixes: 1f2dcf3a154ac ("soundwire: intel: set dev_num_ida_min")
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Chao Song <chao.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221020015624.1703950-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: videobuf2-core: take mmap_lock in vb2_get_unmapped_area()

[ Upstream commit 098e5edc5d048a8df8691fd9fde895af100be42b ]

While vb2_mmap took the mmap_lock mutex, vb2_get_unmapped_area didn't.
Add this.

Also take this opportunity to move the 'q->memory != VB2_MEMORY_MMAP'
check and vb2_fileio_is_active() check into __find_plane_by_offset() so
both vb2_mmap and vb2_get_unmapped_area do the same checks.

Since q->memory is checked while mmap_lock is held, also take that lock
in reqbufs and create_bufs when it is set, and set it back to
MEMORY_UNKNOWN on error.

Fixes: f035eb4e976e ("[media] videobuf2: fix lockdep warning")
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/netback: don't call kfree_skb() with interrupts disabled

[ Upstream commit 74e7e1efdad45580cc3839f2a155174cf158f9b5 ]

It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So remove kfree_skb()
from the spin_lock_irqsave() section and use the already existing
"drop" label in xenvif_start_xmit() for dropping the SKB. At the
same time replace the dev_kfree_skb() call there with a call of
dev_kfree_skb_any(), as xenvif_start_xmit() can be called with
disabled interrupts.

This is XSA-424 / CVE-2022-42328 / CVE-2022-42329.

Fixes: be81992f9086 ("xen/netback: don't queue unlimited number of packages")
Reported-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/netback: do some code cleanup

[ Upstream commit 5834e72eda0b7e5767eb107259d98eef19ebd11f ]

Remove some unused macros and functions, make local functions static.

Signed-off-by: Juergen Gross <jgross@suse.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Link: https://lore.kernel.org/r/20220608043726.9380-1-jgross@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: 74e7e1efdad4 ("xen/netback: don't call kfree_skb() with interrupts disabled")
Signed-off-by: Sasha Levin <sashal@kernel.org>