review.tizen.org Git - platform/kernel/linux-starfive.git/log

powerpc/pmu/fsl: fix is_nmi test for irq mask change

When soft enabled was changed to irq disabled mask, this test missed
being converted (although the equivalent book3s test was converted).

The PMU drivers consider it an NMI when they take a PMI while general
interrupts are disabled. This change restores that behaviour.

Fixes: 01417c6cc7 ("powerpc/64: Change soft_enabled from flag to bitmask")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/time: account broadcast timer event interrupts separately

These are not local timer interrupts but IPIs. It's good to be able
to see how timer offloading is behaving, so split these out into
their own category.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: move a stray NMI IPI case under NMI_IPI ifdef

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: move timer broadcast code under GENERIC_CLOCKEVENTS_BROADCAST ifdef

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: allow soft-NMI watchdog to cover timer interrupts with large decrementers

Large decrementers (e.g., POWER9) can take a very long time to wrap,
so when the timer iterrupt handler sets the decrementer to max so as
to avoid taking another decrementer interrupt when hard enabling
interrupts before running timers, it effectively disables the soft
NMI coverage for timer interrupts.

Fix this by using the traditional 31-bit value instead, which wraps
after a few seconds. masked interrupt code does the same thing, and
in normal operation neither of these paths would ever wrap even the
31 bit value.

Note: the SMP watchdog should catch timer interrupt lockups, but it
is preferable for the local soft-NMI to catch them, mainly to avoid
the IPI.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: generic clockevents broadcast receiver call tick_receive_broadcast

The broadcast tick recipient can call tick_receive_broadcast rather
than re-running the full timer interrupt.

It does not have to check for the next event time, because the sender
already determined the timer has expired. It does not have to test
irq_work_pending, because that's a direct decrementer interrupt and
does not go through the clock events subsystem. And it does not have
to read PURR because that was removed with the previous patch.

This results in no code size change, but both the decrementer and
broadcast path lengths are reduced.

Cc: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/pseries: lparcfg calculate PURR on demand

For SPLPAR, lparcfg provides a sum of PURR registers for all CPUs.
Currently this is done by reading PURR in context switch and timer
interrupt, and storing that into a per-CPU variable. These are summed
to provide the value.

This does not work with all timer schemes (e.g., NO_HZ_FULL), and it
is sub-optimal for performance because it reads the PURR register on
every context switch, although that's been difficult to distinguish
from noise in the contxt_switch microbenchmark.

This patch implements the sum by calling a function on each CPU, to
read and add PURR values of each CPU.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/64: remove start_tb and accum_tb from thread_struct

These fields are only written to.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/64s: micro-optimise __hard_irq_enable() for mtmsrd L=1 support

Book3S minimum supported ISA version now requires mtmsrd L=1. This
instruction does not require bits other than RI and EE to be supplied,
so __hard_irq_enable() and __hard_irq_disable() does not have to read
the kernel_msr from paca.

Interrupt entry code already relies on L=1 support.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/pseries: put cede MSR[EE] check under IRQ_SOFT_MASK_DEBUG

This check does not catch IRQ soft mask bugs, but this option is
slightly more suitable than TRACE_IRQFLAGS.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/64: irq_work avoid interrupt when called with hardware irqs enabled

irq_work_raise should not cause a decrementer exception unless it is
called from NMI context. Doing so often just results in an immediate
masked decrementer interrupt:

   <...>-550    90d...    4us : update_curr_rt <-dequeue_task_rt
   <...>-550    90d...    5us : dbs_update_util_handler <-update_curr_rt
   <...>-550    90d...    6us : arch_irq_work_raise <-irq_work_queue
   <...>-550    90d...    7us : soft_nmi_interrupt <-soft_nmi_common
   <...>-550    90d...    7us : printk_nmi_enter <-soft_nmi_interrupt
   <...>-550    90d.Z.    8us : rcu_nmi_enter <-soft_nmi_interrupt
   <...>-550    90d.Z.    9us : rcu_nmi_exit <-soft_nmi_interrupt
   <...>-550    90d...    9us : printk_nmi_exit <-soft_nmi_interrupt
   <...>-550    90d...   10us : cpuacct_charge <-update_curr_rt

The soft_nmi_interrupt here is the call into the watchdog, due to the
decrementer interrupt firing with irqs soft-disabled. This is
harmless, but sub-optimal.

When it's not called from NMI context or with interrupts enabled, mark
the decrementer pending in the irq_happened mask directly, rather than
having the masked decrementer interupt handler do it. This will be
replayed at the next local_irq_enable. See the comment for details.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powernv/ioda2: Remove redundant free of TCE pages

When IODA2 creates a PE, it creates an IOMMU table with it_ops::free
set to pnv_ioda2_table_free() which calls pnv_pci_ioda2_table_free_pages().

Since iommu_tce_table_put() calls it_ops::free when the last reference
to the table is released, explicit call to pnv_pci_ioda2_table_free_pages()
is not needed so let's remove it.

This should fix double free in the case of PCI hotuplug as
pnv_pci_ioda2_table_free_pages() does not reset neither
iommu_table::it_base nor ::it_size.

This was not exposed by SRIOV as it uses different code path via
pnv_pcibios_sriov_disable().

IODA1 does not inialize it_ops::free so it does not have this issue.

Fixes: c5f7700bbd2e ("powerpc/powernv: Dynamically release PE")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/xmon: use match_string() helper

match_string() returns the index of an array for a matching string,
which can be used instead of open coded variant.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Fix build by disabling attribute-alias warning for SYSCALL_DEFINEx

GCC 8.1 emits warnings such as the following. As arch/powerpc code is
built with -Werror, this breaks the build with GCC 8.1.

  In file included from arch/powerpc/kernel/pci_64.c:23:
  ./include/linux/syscalls.h:233:18: error: 'sys_pciconfig_iobase' alias
  between functions of incompatible types 'long int(long int, long
  unsigned int, long unsigned int)' and 'long int(long int, long int,
  long int)' [-Werror=attribute-alias]
    asmlinkage long sys##name(__MAP(x,__SC_DECL,__VA_ARGS__)) \
                    ^~~
  ./include/linux/syscalls.h:222:2: note: in expansion of macro '__SYSCALL_DEFINEx'
    __SYSCALL_DEFINEx(x, sname, __VA_ARGS__)

This patch inhibits those warnings.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Trim change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/64: Fix strncpy() related build failures with GCC 8.1

GCC 8.1 warns about possible string truncation:

  arch/powerpc/kernel/nvram_64.c:1042:2: error: 'strncpy' specified
  bound 12 equals destination size [-Werror=stringop-truncation]
    strncpy(new_part->header.name, name, 12);

  arch/powerpc/platforms/ps3/repository.c:106:2: error: 'strncpy'
  output truncated before terminating nul copying 8 bytes from a
  string of the same length [-Werror=stringop-truncation]
    strncpy((char *)&n, text, 8);

Fix it by using memcpy(). To make that safe we need to ensure the
destination is pre-zeroed. Use kzalloc() in the nvram code and
initialise the u64 to zero in the ps3 code.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: Use kzalloc() in the nvram code, flesh out change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Merge branch 'topic/pkey' into next

This is a branch with a mixture of mm, x86 and powerpc commits all
relating to some minor cross-arch pkeys consolidation. The x86/mm
changes have been reviewed by Ingo & Dave Hansen and the tree has been
in linux-next for some weeks without issue.

Merge branch 'fixes' into next

We ended up with an ugly conflict between fixes and next in ftrace.h
involving multiple nested ifdefs, and the automatic resolution is
wrong. So merge fixes into next so we can fix it up.

Merge branch 'topic/kbuild' into next

Merge in some commits we're sharing with the kbuild tree.

Merge branch 'topic/ppc-kvm' into next

Merge in some commits we're sharing with the kvm-ppc tree.

powerpc/mm: Fix kernel crash on page table free

Fix the below crash on Book3E 64. pgtable_page_dtor expects struct
page *arg.

Also call the destructor on non book3s platforms correctly. This frees
up the split PTL locks correctly if we had allocated them before.

Call Trace:
  .kmem_cache_free+0x9c/0x44c (unreliable)
  .ptlock_free+0x1c/0x30
  .tlb_remove_table+0xdc/0x224
  .free_pgd_range+0x298/0x500
  .shift_arg_pages+0x10c/0x1e0
  .setup_arg_pages+0x200/0x25c
  .load_elf_binary+0x450/0x16c8
  .search_binary_handler.part.11+0x9c/0x248
  .do_execveat_common.isra.13+0x868/0xc18
  .run_init_process+0x34/0x4c
  .try_to_run_init_process+0x1c/0x68
  .kernel_init+0xdc/0x130
  .ret_from_kernel_thread+0x58/0x7c

Fixes: 702346768 ("powerpc/mm/nohash: Remove pte fragment dependency from nohash")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/prom: Fix %u/%llx usage since prom_printf() change

In commit eae5f709a4d7 ("powerpc: Add __printf verification to
prom_printf") __printf attribute was added to prom_printf(), which
means GCC started warning about type/format mismatches. As part of
that commit we changed some "%lx" formats to "%llx" where the type is
actually unsigned long long.

Unfortunately prom_printf() doesn't know how to print "%llx", it just
prints a literal "lx", eg:

  reserved memory map:
    lx - lx
    lx - lx

prom_printf() also doesn't know how to print "%u" (only "%lu"), it
just prints a literal "u", eg:

  Max number of cores passed to firmware: u (NR_CPUS = 2048)

Instead of:

  Max number of cores passed to firmware: 2048 (NR_CPUS = 2048)

This commit adds support for the missing formatters.

Fixes: eae5f709a4d7 ("powerpc: Add __printf verification to prom_printf")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

cxl: Configure PSL to not use APC virtual machines

APC virtual machines arent used on POWER-9 chips and are already
disabled in on-chip CAPP. They also need to be disabled on the PSL via
'PSL Data Send Control Register' by setting bit(47). This forces the
PSL to send commands to CAPP with queue.id == 0.

Fixes: 5632874311db ("cxl: Add support for POWER9 DD2")
Cc: stable@vger.kernel.org # v4.15+
Signed-off-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

cxl: Disable prefault_mode in Radix mode

Currently we see a kernel-oops reported on Power-9 while attaching a
context to an AFU, with radix-mode and sysfs attr 'prefault_mode' set
to anything other than 'none'. The backtrace of the oops is of this
form:

  Unable to handle kernel paging request for data at address 0x00000080
  Faulting instruction address: 0xc00800000bcf3b20
  cpu 0x1: Vector: 300 (Data Access) at [c00000037f003800]
      pc: c00800000bcf3b20: cxl_load_segment+0x178/0x290 [cxl]
      lr: c00800000bcf39f0: cxl_load_segment+0x48/0x290 [cxl]
      sp: c00000037f003a80
     msr: 9000000000009033
     dar: 80
   dsisr: 40000000
    current = 0xc00000037f280000
    paca    = 0xc0000003ffffe600   softe: 3        irq_happened: 0x01
      pid   = 3529, comm = afp_no_int
  <snip>
  cxl_prefault+0xfc/0x248 [cxl]
  process_element_entry_psl9+0xd8/0x1a0 [cxl]
  cxl_attach_dedicated_process_psl9+0x44/0x130 [cxl]
  native_attach_process+0xc0/0x130 [cxl]
  afu_ioctl+0x3f4/0x5e0 [cxl]
  do_vfs_ioctl+0xdc/0x890
  ksys_ioctl+0x68/0xf0
  sys_ioctl+0x40/0xa0
  system_call+0x58/0x6c

The issue is caused as on Power-8 the AFU attr 'prefault_mode' was
used to improve initial storage fault performance by prefaulting
process segments. However on Power-9 with radix mode we don't have
Storage-Segments that we can prefault. Also prefaulting process Pages
will be too costly and fine-grained.

Hence, since the prefaulting mechanism doesn't makes sense of
radix-mode, this patch updates prefault_mode_store() to not allow any
other value apart from CXL_PREFAULT_NONE when radix mode is enabled.

Fixes: f24be42aab37 ("cxl: Add psl9 specific code")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Acked-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/kbuild: Use flags variables rather than overriding LD/CC/AS

The powerpc toolchain can compile combinations of 32/64 bit and
big/little endian, so it's convenient to consider, e.g.,

`CC -m64 -mbig-endian`

To be the C compiler for the purpose of invoking it to build target
artifacts. So overriding the CC variable to include these flags works
for this purpose.

Unfortunately that is not compatible with the way the proposed new
Kconfig macro language will work.

After previous patches in this series, these flags can be carefully
passed in using flags instead.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/kbuild: Remove CROSS32 defines from top level powerpc Makefile

Switch VDSO32 build over to use CROSS32_COMPILE directly, and have
it pass in -m32 after the standard c_flags. This allows endianness
overrides to be removed and the endian and bitness flags moved into
standard flags variables.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/kbuild: Set default generic machine type for 32-bit compile

Some 64-bit toolchains uses the wrong ISA variant for compiling 32-bit
kernels, even with -m32. Debian's powerpc64le is one such case, and
that is because it is built with --with-cpu=power8.

So when cross compiling a 32-bit kernel with a 64-bit toolchain, set
-mcpu=powerpc initially, which is the generic 32-bit powerpc machine
type and scheduling model. CPU and platform code can override this
with subsequent -mcpu flags if necessary.

This is not done for 32-bit toolchains otherwise it would override
their defaults, which are presumably set appropriately for the
environment (moreso than a 64-bit cross compiler).

This fixes a lot of build failures due to incompatible assembly when
compiling 32-bit kernel with the Debian powerpc64le 64-bit toolchain.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/livepatch: Fix build error with kprobes disabled.

arch/powerpc/kernel/stacktrace.c: In function ‘save_stack_trace_tsk_reliable’:
arch/powerpc/kernel/stacktrace.c:176:28: error: ‘kretprobe_trampoline’ undeclared
if (ip == (unsigned long)kretprobe_trampoline)
^~~~~~~~~~~~~~~~~~~~

Fixes: df78d3f61480 ("powerpc/livepatch: Implement reliable stack tracing for the consistency model")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

selftests/powerpc: Add core file test for Protection Key registers

This test verifies that the AMR, IAMR and UAMOR are being written to a
process' core file.

Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
[mpe: Simplify make rule]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

selftests/powerpc: Add ptrace tests for Protection Key registers

This test exercises read and write access to the AMR, IAMR and UAMOR.

Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
[mpe: Simplify make rule]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/modules: remove unused mod_arch_specific.toc field

The toc field in the mod_arch_specific struct isn't actually used
anywhere, so remove it.

Also the ftrace-specific fields are now common between 32-bit and
64-bit, so simplify the struct definition a bit by moving them out of
the __powerpc64__ #ifdef.

Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powernv/cpuidle: Init all present cpus for deep states

Init all present cpus for deep states instead of "all possible" cpus.
Init fails if a possible cpu is guarded. Resulting in making only
non-deep states available for cpuidle/hotplug.

Stewart says, this means that for single threaded workloads, if you
guard out a CPU core you'll not get WoF (Workload Optimised
Frequency), which means that performance goes down when you wouldn't
expect it to.

Fixes: 77b54e9f213f ("powernv/powerpc: Add winkle support for offline cpus")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Akshay Adiga <akshay.adiga@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/perf: Update raw-event code encoding comment for power8

Comment explanning the raw event code encoding for Power8 was
moved to isa207_common.h file when re-factoring the code to
support power9. But then Power9 pmu branched out due to changes
specific to power9. So move the encoding comment back to power8-pmu.c
Just comment movement and no logic change.

Fixes: 4d3576b20716 ('powerpc/perf: factor out power8 pmu macros and defines')
Signed-off-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Add a missing include header

The header file <asm/switch_to.h> was missing from the includes. Fix the
following warning, treated as error with W=1:

arch/powerpc/kernel/vecemu.c:260:5: error: no previous prototype for ‘emulate_altivec’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/32: Add a missing include header

The header file <linux/syscalls.h> was missing from the includes. Fix the
following warning, treated as error with W=1:

arch/powerpc/kernel/pci_32.c:286:6: error: no previous prototype for ‘sys_pciconfig_iobase’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/chrp/time: Make some functions static, add missing header include

Add a missing include <platforms/chrp/chrp.h>.

These functions can all be static, make it so. Fix warnings treated as
errors with W=1:

  arch/powerpc/platforms/chrp/time.c:41:13: error: no previous prototype for ‘chrp_time_init’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/time.c:66:5: error: no previous prototype for ‘chrp_cmos_clock_read’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/time.c:74:6: error: no previous prototype for ‘chrp_cmos_clock_write’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/time.c:86:5: error: no previous prototype for ‘chrp_set_rtc_time’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/time.c:130:6: error: no previous prototype for ‘chrp_get_rtc_time’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/tau: Make some function static

These functions can all be static, make it so. Fix warnings treated as
errors with W=1:

  arch/powerpc/kernel/tau_6xx.c:53:6: error: no previous prototype for ‘set_thresholds’ [-Werror=missing-prototypes]
  arch/powerpc/kernel/tau_6xx.c:73:6: error: no previous prototype for ‘TAUupdate’ [-Werror=missing-prototypes]
  arch/powerpc/kernel/tau_6xx.c:208:13: error: no previous prototype for ‘TAU_init_smp’ [-Werror=missing-prototypes]
  arch/powerpc/kernel/tau_6xx.c:220:12: error: no previous prototype for ‘TAU_init’ [-Werror=missing-prototypes]
  arch/powerpc/kernel/tau_6xx.c:126:6: error: no previous prototype for ‘TAUException’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Make function btext_initialize static

This function can be static, make it so, this fix a warning treated as
error with W=1:

arch/powerpc/kernel/btext.c:173:5: error: no previous prototype for ‘btext_initialize’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/tau: Synchronize function prototypes and body

Some function prototypes and body for Thermal Assist Units were not in
sync. Update the function definition to match the existing function
declaration found in `setup-common.c`, changing an `int` return type to a
`u32` return type. Move the prototypes to a header file. Fix the following
warnings, treated as error with W=1:

  arch/powerpc/kernel/tau_6xx.c:257:5: error: no previous prototype for ‘cpu_temp_both’ [-Werror=missing-prototypes]
  arch/powerpc/kernel/tau_6xx.c:262:5: error: no previous prototype for ‘cpu_temp’ [-Werror=missing-prototypes]
  arch/powerpc/kernel/tau_6xx.c:267:5: error: no previous prototype for ‘tau_interrupts’ [-Werror=missing-prototypes]

Compile tested with CONFIG_TAU_INT.

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Add missing prototype

Add one missing prototype for function rh_dump_blk. Fix warning treated as
error in W=1:

arch/powerpc/lib/rheap.c:740:6: error: no previous prototype for ‘rh_dump_blk’ [-Werror=missing-prototypes]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/52xx: Add missing functions prototypes

The function prototypes were declared within a `#ifdef CONFIG_PPC_LITE5200`
block which would prevent them from being visible when compiling
`mpc52xx_pm.c`. Move the prototypes outside of the `#ifdef` block to fix
the following warnings treated as errors with W=1:

  arch/powerpc/platforms/52xx/mpc52xx_pm.c:58:5: error: no previous prototype for ‘mpc52xx_pm_prepare’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/52xx/mpc52xx_pm.c:113:5: error: no previous prototype for ‘mpc52xx_pm_enter’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/52xx/mpc52xx_pm.c:181:6: error: no previous prototype for ‘mpc52xx_pm_finish’ [-Werror=missing-prototypes]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powermac: Add missing prototype for note_bootable_part()

Add a missing prototype for function `note_bootable_part` to silence a
warning treated as error with W=1:

arch/powerpc/platforms/powermac/setup.c:361:12: error: no previous prototype for ‘note_bootable_part’ [-Werror=missing-prototypes]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powermac: Move pmac_pfunc_base_install prototype to header file

The pmac_pfunc_base_install prototype was declared in powermac/smp.c since
function was used there, move it to pmac_pfunc.h header to be visible in
pfunc_base.c. Fix a warning treated as error with W=1:

arch/powerpc/platforms/powermac/pfunc_base.c:330:12: error: no previous prototype for ‘pmac_pfunc_base_install’ [-Werror=missing-prototypes]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/chrp/pci: Make some functions static

These functions can all be static, make it so. Fix warnings treated as
errors with W=1:

  arch/powerpc/platforms/chrp/pci.c:34:5: error: no previous prototype for ‘gg2_read_config’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/pci.c:61:5: error: no previous prototype for ‘gg2_write_config’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/pci.c:97:5: error: no previous prototype for ‘rtas_read_config’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/pci.c:112:5: error: no previous prototype for ‘rtas_write_config’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powermac: Mark variable x as unused

Since the value of x is never intended to be read, declare it with gcc
attribute as unused. Fix warning treated as error with W=1:

arch/powerpc/platforms/powermac/bootx_init.c:471:21: error: variable ‘x’ set but not used [-Werror=unused-but-set-variable]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/chrp/setup: Remove idu_size variable and make some functions static

Remove variable declaration idu_size and associated code since not used.

These functions can all be static, make it so. Fix warnings treated as
errors with W=1:

  arch/powerpc/platforms/chrp/setup.c:97:6: error: no previous prototype for ‘chrp_show_cpuinfo’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/setup.c:302:13: error: no previous prototype for ‘chrp_setup_arch’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/setup.c:385:16: error: variable ‘idu_size’ set but not used [-Werror=unused-but-set-variable]
  arch/powerpc/platforms/chrp/setup.c:526:13: error: no previous prototype for ‘chrp_init_IRQ’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/chrp/setup.c:559:1: error: no previous prototype for ‘chrp_init2’ [-Werror=missing-prototypes]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/wii: Make hlwd_pic_init function static

The function hlwd_pic_init can be made static, so do it. Fix the following
warning treated as error (W=1):

../arch/powerpc/platforms/embedded6xx/hlwd-pic.c:158:20: error: no previous prototype for ‘hlwd_pic_init’ [-Werror=missing-prototypes]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/radix: Use do/while(0) trick for single statement block

In commit 7a22d6321c3d ("powerpc/mm/radix: Update command line parsing for
disable_radix") an `if` statement was added for a possible empty body
(prom_debug).

Fix the following warning, treated as error with W=1:

arch/powerpc/kernel/prom_init.c:656:46: error: suggest braces around empty body in an ‘if’ statement [-Werror=empty-body]

Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/sparse: Fix plain integer as NULL pointer warning

Trivial fix to remove the following sparse warnings:

  arch/powerpc/kernel/module_32.c:112:74: warning: Using plain integer as NULL pointer
  arch/powerpc/kernel/module_32.c:117:74: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:1155:28: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:1230:20: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:1385:36: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:1752:23: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:2084:19: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:2110:32: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:2167:19: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:2183:19: warning: Using plain integer as NULL pointer
  drivers/macintosh/via-pmu.c:277:20: warning: Using plain integer as NULL pointer
  arch/powerpc/platforms/powermac/setup.c:155:67: warning: Using plain integer as NULL pointer
  arch/powerpc/platforms/powermac/setup.c:247:27: warning: Using plain integer as NULL pointer
  arch/powerpc/platforms/powermac/setup.c:249:27: warning: Using plain integer as NULL pointer
  arch/powerpc/platforms/powermac/setup.c:252:37: warning: Using plain integer as NULL pointer
  arch/powerpc/mm/tlb_hash32.c:127:21: warning: Using plain integer as NULL pointer
  arch/powerpc/mm/tlb_hash32.c:148:21: warning: Using plain integer as NULL pointer
  arch/powerpc/mm/tlb_hash32.c:44:21: warning: Using plain integer as NULL pointer
  arch/powerpc/mm/tlb_hash32.c:57:21: warning: Using plain integer as NULL pointer
  arch/powerpc/mm/tlb_hash32.c:87:21: warning: Using plain integer as NULL pointer
  arch/powerpc/kernel/btext.c:160:31: warning: Using plain integer as NULL pointer
  arch/powerpc/kernel/btext.c:167:22: warning: Using plain integer as NULL pointer
  arch/powerpc/kernel/btext.c:274:21: warning: Using plain integer as NULL pointer
  arch/powerpc/kernel/btext.c:285:31: warning: Using plain integer as NULL pointer
  arch/powerpc/include/asm/hugetlb.h:204:16: warning: Using plain integer as NULL pointer
  arch/powerpc/mm/ppc_mmu_32.c:170:21: warning: Using plain integer as NULL pointer
  arch/powerpc/platforms/powermac/pci.c:1227:23: warning: Using plain integer as NULL pointer
  arch/powerpc/platforms/powermac/pci.c:65:24: warning: Using plain integer as NULL pointer

Also use `--fix` command line option from `script/checkpatch --strict` to
remove the following:

  CHECK: Comparison to NULL could be written "!dispDeviceBase"
  #72: FILE: arch/powerpc/kernel/btext.c:160:
  + if (dispDeviceBase == NULL)

  CHECK: Comparison to NULL could be written "!vbase"
  #80: FILE: arch/powerpc/kernel/btext.c:167:
  + if (vbase == NULL)

  CHECK: Comparison to NULL could be written "!base"
  #89: FILE: arch/powerpc/kernel/btext.c:274:
  + if (base == NULL)

  CHECK: Comparison to NULL could be written "!dispDeviceBase"
  #98: FILE: arch/powerpc/kernel/btext.c:285:
  + if (dispDeviceBase == NULL)

  CHECK: Comparison to NULL could be written "strstr"
  #117: FILE: arch/powerpc/kernel/module_32.c:117:
  + if (strstr(secstrings + sechdrs[i].sh_name, ".debug") != NULL)

  CHECK: Comparison to NULL could be written "!Hash"
  #130: FILE: arch/powerpc/mm/ppc_mmu_32.c:170:
  + if (Hash == NULL)

  CHECK: Comparison to NULL could be written "Hash"
  #143: FILE: arch/powerpc/mm/tlb_hash32.c:44:
  + if (Hash != NULL) {

  CHECK: Comparison to NULL could be written "!Hash"
  #152: FILE: arch/powerpc/mm/tlb_hash32.c:57:
  + if (Hash == NULL) {

  CHECK: Comparison to NULL could be written "!Hash"
  #161: FILE: arch/powerpc/mm/tlb_hash32.c:87:
  + if (Hash == NULL) {

  CHECK: Comparison to NULL could be written "!Hash"
  #170: FILE: arch/powerpc/mm/tlb_hash32.c:127:
  + if (Hash == NULL) {

  CHECK: Comparison to NULL could be written "!Hash"
  #179: FILE: arch/powerpc/mm/tlb_hash32.c:148:
  + if (Hash == NULL) {

  ERROR: space required after that ';' (ctx:VxV)
  #192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
  + for (; node != NULL;node = node->sibling) {

  CHECK: Comparison to NULL could be written "node"
  #192: FILE: arch/powerpc/platforms/powermac/pci.c:65:
  + for (; node != NULL;node = node->sibling) {

  CHECK: Comparison to NULL could be written "!region"
  #201: FILE: arch/powerpc/platforms/powermac/pci.c:1227:
  + if (region == NULL)

  CHECK: Comparison to NULL could be written "of_get_property"
  #214: FILE: arch/powerpc/platforms/powermac/setup.c:155:
  + if (of_get_property(np, "cache-unified", NULL) != NULL && dc) {

  CHECK: Comparison to NULL could be written "!np"
  #223: FILE: arch/powerpc/platforms/powermac/setup.c:247:
  + if (np == NULL)

  CHECK: Comparison to NULL could be written "np"
  #226: FILE: arch/powerpc/platforms/powermac/setup.c:249:
  + if (np != NULL) {

  CHECK: Comparison to NULL could be written "l2cr"
  #230: FILE: arch/powerpc/platforms/powermac/setup.c:252:
  + if (l2cr != NULL) {

  CHECK: Comparison to NULL could be written "via"
  #243: FILE: drivers/macintosh/via-pmu.c:277:
  + if (via != NULL)

  CHECK: Comparison to NULL could be written "current_req"
  #252: FILE: drivers/macintosh/via-pmu.c:1155:
  + if (current_req != NULL) {

  CHECK: Comparison to NULL could be written "!req"
  #261: FILE: drivers/macintosh/via-pmu.c:1230:
  + if (req == NULL || pmu_state != idle

  CHECK: Comparison to NULL could be written "!req"
  #270: FILE: drivers/macintosh/via-pmu.c:1385:
  + if (req == NULL) {

  CHECK: Comparison to NULL could be written "!pp"
  #288: FILE: drivers/macintosh/via-pmu.c:2084:
  + if (pp == NULL)

  CHECK: Comparison to NULL could be written "!pp"
  #297: FILE: drivers/macintosh/via-pmu.c:2110:
  + if (count < 1 || pp == NULL)

  CHECK: Comparison to NULL could be written "!pp"
  #306: FILE: drivers/macintosh/via-pmu.c:2167:
  + if (pp == NULL)

  CHECK: Comparison to NULL could be written "pp"
  #315: FILE: drivers/macintosh/via-pmu.c:2183:
  + if (pp != NULL) {

Link: https://github.com/linuxppc/linux/issues/37
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/altivec: Add missing prototypes for altivec

Some functions prototypes were missing for the non-altivec code. Add the
missing prototypes in a new header file, fix warnings treated as errors
with W=1:

  arch/powerpc/lib/xor_vmx_glue.c:18:6: error: no previous prototype for ‘xor_altivec_2’ [-Werror=missing-prototypes]
  arch/powerpc/lib/xor_vmx_glue.c:29:6: error: no previous prototype for ‘xor_altivec_3’ [-Werror=missing-prototypes]
  arch/powerpc/lib/xor_vmx_glue.c:40:6: error: no previous prototype for ‘xor_altivec_4’ [-Werror=missing-prototypes]
  arch/powerpc/lib/xor_vmx_glue.c:52:6: error: no previous prototype for ‘xor_altivec_5’ [-Werror=missing-prototypes]

The prototypes were already present in <asm/xor.h> but this header file is
meant to be included after <include/linux/raid/xor.h>. Trying to re-use
<asm/xor.h> directly would lead to warnings such as:

  arch/powerpc/include/asm/xor.h:39:15: error: variable ‘xor_block_altivec’ has initializer but incomplete type

Trying to re-use <asm/xor.h> after <include/linux/raid/xor.h> in
xor_vmx_glue.c would in turn trigger the following warnings:

  include/asm-generic/xor.h:688:34: error: ‘xor_block_32regs’ defined but not used [-Werror=unused-variable]

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Add __printf verification to prom_printf

__printf is useful to verify format and arguments. Fix arg mismatch
reported by gcc, remove the following warnings (with W=1):

  arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’
  arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’
  arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’

The patch also include arg mismatch fix for case with #define DEBUG_PROM
(warning not listed here).

This patch fix also the following warnings revealed by checkpatch:

  WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string
  #101: FILE: arch/powerpc/kernel/prom_init.c:1235:
  + prom_debug("alloc_up(%lx, %lx)\n", size, align);

and

  WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string
  #138: FILE: arch/powerpc/kernel/prom_init.c:1278:
  + prom_debug("alloc_down(%lx, %lx, %s)\n", size, align,

Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/xmon: Update paca fields dumped in xmon

The set of paca fields we dump in xmon has gotten somewhat out of
date. Update to add some recently added fields.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/xmon: Realign paca dump fields

We've added some fields with longer names since we originally wrote
this, so the fields are no longer lined up. Adjust the widths to make
it all look nice again, eg:

  0:mon> dp
  paca for cpu 0x0 @ c000000001fa0000:
   possible                  = yes
   ...
   slb_shadow            [0] = 0xc000000008000000 0x400ea1b217000500
   slb_shadow            [1] = 0xd000000008000001 0x400d43642f000510
   ...
   rfi_flush_fallback_area   = c0000000fff80000   (0xcc8)
   ...
   accounting.starttime_user = 0x51582f07         (0xae8)

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/xmon: Add __printf annotation to xmon_printf()

This allows the compiler to verify the format strings vs the types of
the arguments.

Update the other prototype declarations in asm/xmon.h.

Silence warnings (triggered at W=1) by adding relevant __printf
attribute. Move #define at bottom of the file to prevent conflict with
gcc attribute.

Solves the original warning:

arch/powerpc/xmon/nonstdio.c:178:2: error: function might be
possible candidate for ‘gnu_printf’ format attribute

In turn this uncovered many formatting errors in xmon.c, all fixed in
this patch.

Signed-off-by: Mathieu Malaterre <malat@debian.org>
[mpe: Always use px not p, fixup the 44x specific code, tweak change log]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/xmon: Specify the full format in DUMP() macro

In dump_one_paca() the DUMP macro unconditionally prepends '#' to the
printf format specifier. In most cases we're using either 'x' or 'lx'
etc. and that is OK. But for 'p' and other formats using '#' is
actually undefined, and once we enable printf() checking for
xmon_printf() we will get warnings from the compiler.

So just have each usage specify the full format, that way we can omit
'#' when it's inappropriate.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Mathieu Malaterre <malat@debian.org>

powerpc/xmon: Also setup debugger hooks when single-stepping

When single-stepping kernel code from xmon without a debug hook
enabled the kernel crashes. This can happen when kernel starts with
xmon on crash disabled but xmon is entered using sysrq.

Call force_enable_xmon when single-stepping in xmon to install the
xmon debug hooks.

Fixes: e1368d0c9edb ("powerpc/xmon: Setup debugger hooks when first break-point is set")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/8xx: fix invalid register expression in head_8xx.S

New binutils generate the following warning

AS arch/powerpc/kernel/head_8xx.o
arch/powerpc/kernel/head_8xx.S: Assembler messages:
arch/powerpc/kernel/head_8xx.S:916: Warning: invalid register expression

This patch fixes it.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

selftests/powerpc: Add ptrace hw breakpoint test

This test the ptrace hw breakpoints via PTRACE_SET_DEBUGREG and
PPC_PTRACE_SETHWDEBUG.  This test was use to find the bugs fixed by
these recent commits:

  4f7c06e26e powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREG
  cd6ef7eebf powerpc/ptrace: Fix enforcement of DAWR constraints

Signed-off-by: Michael Neuling <mikey@neuling.org>
[mpe: Add SPDX tag, clang format it]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

selftests/powerpc: Add missing .gitignores

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm: Only read faulting instruction when necessary in do_page_fault()

Commit a7a9dcd882a67 ("powerpc: Avoid taking a data miss on every
userspace instruction miss") has shown that limiting the read of
faulting instruction to likely cases improves performance.

This patch goes further into this direction by limiting the read
of the faulting instruction to the only cases where it is likely
needed.

On an MPC885, with the same benchmark app as in the commit referred
above, we see a reduction of about 3900 dTLB misses (approx 3%):

Before the patch:
Performance counter stats for './fault 500' (10 runs):

         683033312      cpu-cycles                                                    ( +-  0.03% )
            134538      dTLB-load-misses                                              ( +-  0.03% )
             46099      iTLB-load-misses                                              ( +-  0.02% )
             19681      faults                                                        ( +-  0.02% )

       5.389747878 seconds time elapsed                                          ( +-  0.06% )

With the patch:

Performance counter stats for './fault 500' (10 runs):

         682112862      cpu-cycles                                                    ( +-  0.03% )
            130619      dTLB-load-misses                                              ( +-  0.03% )
             46073      iTLB-load-misses                                              ( +-  0.05% )
             19681      faults                                                        ( +-  0.01% )

       5.381342641 seconds time elapsed                                          ( +-  0.07% )

The proper work of the huge stack expansion was tested with the
following app:

int main(int argc, char **argv)
{
char buf[1024 * 1025];

sprintf(buf, "Hello world !\n");
printf(buf);

exit(0);
}

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
[mpe: Add include of pagemap.h to fix build errors]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm: Use instruction symbolic names in store_updates_sp()

Use symbolic names defined in asm/ppc-opcode.h
instead of hardcoded values.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Export tm_enable()/tm_disable/tm_abort() APIs

This patch exports tm_enable()/tm_disable/tm_abort() APIs, which
will be used for PR KVM transactional memory logic.

Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/reg: Add TEXASR related macros

This patches add some macros for CR0/TEXASR bits so that PR KVM TM
logic (tbegin./treclaim./tabort.) can make use of them later.

Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Export msr_check_and_set() to modules

PR KVM will need to reuse msr_check_and_set().
This patch exports this API for reuse.

Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Reviewed-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

hwmon: (ibmpowernv) Add energy sensors

This patch exports the accumulated power numbers of each power
sensor maintained by OCC.

Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

hwmon: (ibmpowernv): Add support to read 64 bit sensors

The firmware has supported for reading sensor values of size u32.
This patch adds support to use newer firmware functions which allows
to read the sensors of size u64.

Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powernv: opal-sensor: Add support to read 64bit sensor values

This patch adds support to read 64-bit sensor values. This method is
used to read energy sensors and counters which are of type u64.

Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

selftests/powerpc: Remove redundant cp_abort test

Paste on POWER9 only works on accelerators and no longer on real
memory. Hence this test is broken so remove it.

Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/fsl/dts: fix the i2c-mux compatible for t104xqds

The sanctioned compatible is "nxp,pca9547".

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREG

In commit e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when
validating DAWR region end") we fixed setting the DAWR end point to
its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke
PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint.

PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to
zero (memset() in hw_breakpoint_init()). This worked with
arch_validate_hwbkpt_settings() before the above patch was applied but
is now broken if the breakpoint is 512byte aligned.

This sets the length of the breakpoint to 8 bytes when using
PTRACE_SET_DEBUGREG.

Fixes: e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when validating DAWR region end")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/ptrace: Fix enforcement of DAWR constraints

Back when we first introduced the DAWR, in commit 4ae7ebe9522a
("powerpc: Change hardware breakpoint to allow longer ranges"), we
screwed up the constraint making it a 1024 byte boundary rather than a
512. This makes the check overly permissive. Fortunately GDB is the
only real user and it always did they right thing, so we never
noticed.

This fixes the constraint to 512 bytes.

Fixes: 4ae7ebe9522a ("powerpc: Change hardware breakpoint to allow longer ranges")
Cc: stable@vger.kernel.org # v3.9+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powernv: Use __raw_[rm_]writeq_be() in npu-dma.c

This allows us to squash some sparse warnings and also avoids having
to do explicity endian conversions in the code.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>

powerpc/powernv: Use __raw_[rm_]writeq_be() in pci-ioda.c

This allows us to squash some sparse warnings and also avoids having
to do explicity endian conversions in the code.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>

powerpc/io: Add __raw_writeq_be() __raw_rm_writeq_be()

Add byte-swapping versions of __raw_writeq() and __raw_rm_writeq().

This allows us to avoid sparse warnings caused by passing __be64 to
__raw_writeq(), which takes unsigned long:

  arch/powerpc/platforms/powernv/pci-ioda.c:1981:38:
  warning: incorrect type in argument 1 (different base types)
      expected unsigned long [unsigned] v
      got restricted __be64 [usertype] <noident>

It's also generally preferable to use a byte-swapping accessor rather
than doing it by hand in the code, which is more bug prone.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>

powerpc/perf: Fix memory allocation for core-imc based on num_possible_cpus()

Currently memory is allocated for core-imc based on cpu_present_mask,
which has bit 'cpu' set iff cpu is populated. We use (cpu number / threads
per core) as the array index to access the memory.

Under some circumstances firmware marks a CPU as GUARDed CPU and boot the
system, until cleared of errors, these CPU's are unavailable for all
subsequent boots. GUARDed CPUs are possible but not present from linux
view, so it blows a hole when we assume the max length of our allocation
is driven by our max present cpus, where as one of the cpus might be online
and be beyond the max present cpus, due to the hole.
So (cpu number / threads per core) value bounds the array index and leads
to memory overflow.

Call trace observed during a guard test:

Faulting instruction address: 0xc000000000149f1c
cpu 0x69: Vector: 380 (Data Access Out of Range) at [c000003fea303420]
    pc:c000000000149f1c: prefetch_freepointer+0x14/0x30
    lr:c00000000014e0f8: __kmalloc+0x1a8/0x1ac
    sp:c000003fea3036a0
   msr:9000000000009033
   dar:c9c54b2c91dbf6b7
  current = 0xc000003fea2c0000
  paca    = 0xc00000000fddd880 softe: 3 irq_happened: 0x01
    pid   = 1, comm = swapper/104
Linux version 4.16.7-openpower1 (smc@smc-desktop) (gcc version 6.4.0
(Buildroot 2018.02.1-00006-ga8d1126)) #2 SMP Fri May 4 16:44:54 PDT 2018
enter ? for help
call trace:
__kmalloc+0x1a8/0x1ac
(unreliable)
init_imc_pmu+0x7f4/0xbf0
opal_imc_counters_probe+0x3fc/0x43c
platform_drv_probe+0x48/0x80
driver_probe_device+0x22c/0x308
__driver_attach+0xa0/0xd8
bus_for_each_dev+0x88/0xb4
driver_attach+0x2c/0x40
bus_add_driver+0x1e8/0x228
driver_register+0xd0/0x114
__platform_driver_register+0x50/0x64
opal_imc_driver_init+0x24/0x38
do_one_initcall+0x150/0x15c
kernel_init_freeable+0x250/0x254
kernel_init+0x1c/0x150
ret_from_kernel_thread+0x5c/0xc8

Allocating memory for core-imc based on cpu_possible_mask, which has
bit 'cpu' set iff cpu is populatable, will fix this issue.

Reported-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Signed-off-by: Anju T Sudhakar <anju@linux.vnet.ibm.com>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Tested-by: Pridhiviraj Paidipeddi <ppaidipe@linux.vnet.ibm.com>
Fixes: 39a846db1d57 ("powerpc/perf: Add core IMC PMU support")
Cc: stable@vger.kernel.org # v4.14+
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/rtas: Fix spelling mistake "Discharching" -> "Discharging"

Trivial fix to spelling mistake in battery_charging array.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/64s: Clear PCR on boot

Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.

We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).

Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/lib: Fix "integer constant is too large" build failure

My powerpc-linux-gnu-gcc v4.4.5 compiler can't build a 32-bit kernel
any more:

arch/powerpc/lib/sstep.c: In function 'do_popcnt':
arch/powerpc/lib/sstep.c:1068: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1069: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1070: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c:1079: error: integer constant is too large for 'long' type
arch/powerpc/lib/sstep.c: In function 'do_prty':
arch/powerpc/lib/sstep.c:1117: error: integer constant is too large for 'long' type

This file gets compiled with -std=gnu89 which means a constant can be
given the type 'long' even if it won't fit. Fix the errors with a 'ULL'
suffix on the relevant constants.

Fixes: 2c979c489fee ("powerpc/lib/sstep: Add prty instruction emulation")
Fixes: dcbd19b48d31 ("powerpc/lib/sstep: Add popcnt instruction emulation")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powernv: Fix NVRAM sleep in invalid context when crashing

Similarly to opal_event_shutdown, opal_nvram_write can be called in
the crash path with irqs disabled. Special case the delay to avoid
sleeping in invalid context.

Fixes: 3b8070335f75 ("powerpc/powernv: Fix OPAL NVRAM driver OPAL_BUSY loops")
Cc: stable@vger.kernel.org # v3.2
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/powernv: Fix opal_event_shutdown() called with interrupts disabled

A kernel crash in process context that calls emergency_restart from
panic will end up calling opal_event_shutdown with interrupts disabled
but not in interrupt. This causes a sleeping function to be called
which gives the following warning with sysrq+c:

    Rebooting in 10 seconds..
    BUG: sleeping function called from invalid context at kernel/locking/mutex.c:238
    in_atomic(): 0, irqs_disabled(): 1, pid: 7669, name: bash
    CPU: 20 PID: 7669 Comm: bash Tainted: G      D W         4.17.0-rc5+ #3
    Call Trace:
    dump_stack+0xb0/0xf4 (unreliable)
    ___might_sleep+0x174/0x1a0
    mutex_lock+0x38/0xb0
    __free_irq+0x68/0x460
    free_irq+0x70/0xc0
    opal_event_shutdown+0xb4/0xf0
    opal_shutdown+0x24/0xa0
    pnv_shutdown+0x28/0x40
    machine_shutdown+0x44/0x60
    machine_restart+0x28/0x80
    emergency_restart+0x30/0x50
    panic+0x2a0/0x328
    oops_end+0x1ec/0x1f0
    bad_page_fault+0xe8/0x154
    handle_page_fault+0x34/0x38
    --- interrupt: 300 at sysrq_handle_crash+0x44/0x60
    LR = __handle_sysrq+0xfc/0x260
    flag_spec.62335+0x12b844/0x1e8db4 (unreliable)
    __handle_sysrq+0xfc/0x260
    write_sysrq_trigger+0xa8/0xb0
    proc_reg_write+0xac/0x110
    __vfs_write+0x6c/0x240
    vfs_write+0xd0/0x240
    ksys_write+0x6c/0x110

Fixes: 9f0fd0499d30 ("powerpc/powernv: Add a virtual irqchip for opal events")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/32: Use stmw/lmw for registers save/restore in asm

arch/powerpc/Makefile activates -mmultiple on BE PPC32 configs
in order to use multiple word instructions in functions entry/exit.

The patch does the same for the asm parts, for consistency.

On processors like the 8xx on which insn fetching is pretty slow,
this speeds up registers save/restore.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
[mpe: PPC32 is BE only, so drop the endian checks]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: Avoid an unnecessary test and branch in longjmp()

Doing the test at exit of the function avoids an unnecessary
test and branch inside longjmp().

Semantics are unchanged.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Revert "powerpc/64: Fix checksum folding in csum_add()"

This reverts commit 6ad966d7303b70165228dba1ee8da1a05c10eefe.

That commit was pointless, because csum_add() sums two 32 bits
values, so the sum is 0x1fffffffe at the maximum.
And then when adding upper part (1) and lower part (0xfffffffe),
the result is 0xffffffff which doesn't carry.
Any lower value will not carry either.

And behind the fact that this commit is useless, it also kills the
whole purpose of having an arch specific inline csum_add()
because the resulting code gets even worse than what is obtained
with the generic implementation of csum_add()

0000000000000240 <.csum_add>:
240: 38 00 ff ff li      r0,-1
244: 7c 84 1a 14 add     r4,r4,r3
248: 78 00 00 20 clrldi  r0,r0,32
24c: 78 89 00 22 rldicl  r9,r4,32,32
250: 7c 80 00 38 and     r0,r4,r0
254: 7c 09 02 14 add     r0,r9,r0
258: 78 09 00 22 rldicl  r9,r0,32,32
25c: 7c 00 4a 14 add     r0,r0,r9
260: 78 03 00 20 clrldi  r3,r0,32
264: 4e 80 00 20 blr

In comparison, the generic implementation of csum_add() gives:

0000000000000290 <.csum_add>:
290: 7c 63 22 14 add     r3,r3,r4
294: 7f 83 20 40 cmplw   cr7,r3,r4
298: 7c 10 10 26 mfocrf  r0,1
29c: 54 00 ef fe rlwinm  r0,r0,29,31,31
2a0: 7c 60 1a 14 add     r3,r0,r3
2a4: 78 63 00 20 clrldi  r3,r3,32
2a8: 4e 80 00 20 blr

And the reverted implementation for PPC64 gives:

0000000000000240 <.csum_add>:
240: 7c 84 1a 14 add     r4,r4,r3
244: 78 80 00 22 rldicl  r0,r4,32,32
248: 7c 80 22 14 add     r4,r0,r4
24c: 78 83 00 20 clrldi  r3,r4,32
250: 4e 80 00 20 blr

Fixes: 6ad966d7303b7 ("powerpc/64: Fix checksum folding in csum_add()")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Acked-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc: get rid of PMD_PAGE_SIZE() and _PMD_SIZE

PMD_PAGE_SIZE() is nowhere used and _PMD_SIZE is only
used by PMD_PAGE_SIZE().

This patch removes them.

Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/kvm: Prefer fault_in_pages_readable function

Directly use fault_in_pages_readable instead of manual __get_user code. Fix
warning treated as error with W=1:

arch/powerpc/kernel/kvm.c:675:6: error: variable ‘tmp’ set but not used [-Werror=unused-but-set-variable]

Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/radix: implement LPID based TLB flushes to be used by KVM

Implement a local TLB flush for invalidating an LPID with variants for
process or partition scope. And a global TLB flush for invalidating
a partition scoped page of an LPID.

These will be used by KVM in subsequent patches.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/embedded6xx/hlwd-pic: Prevent interrupts from being handled by Starlet

The interrupt controller inside the Wii's Hollywood chip is connected to
two masters, the "Broadway" PowerPC and the "Starlet" ARM926, each with
their own interrupt status and mask registers.

When booting the Wii with mini[1], interrupts from the SD card
controller (IRQ 7) are handled by the ARM, because mini provides SD
access over IPC. Linux however can't currently use or disable this IPC
service, so both sides try to handle IRQ 7 without coordination.

Let's instead make sure that all interrupts that are unmasked on the PPC
side are masked on the ARM side; this will also make sure that Linux can
properly talk to the SD card controller (and potentially other devices).

If access to a device through IPC is desired in the future, interrupts
from that device should not be handled by Linux directly.

[1]: https://github.com/lewurm/mini

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/embedded6xx/flipper-pic: Don't match all IRQ domains

On the Wii, there is a secondary IRQ controller (hlwd-pic), so
flipper-pic's match operation should not be hardcoded to return 1.
In fact, the default matching logic is sufficient, and we can completely
omit flipper_pic_match.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm: Use page fragments for allocation page table at PMD level

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm: Implement helpers for pagetable fragment support at PMD level

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/book3s64/mm: Simplify the rcu callback for page table free

Instead of encoding shift in the table address, use an enumerated index value.
This allow us to do different things in the callback for pte and pmd.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/book3s64/4k: Switch 4k pagesize config to use pagetable fragment

4K config use one full page at level 4 of the pagetable. Add support for single
fragment allocation in pagetable fragment code and and use that for 4K config.
This makes both 4k and 64k use the same code path. Later we will switch pmd to
use the page table fragment code. This is done only for 64bit platforms which
is using page table fragment support.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/nohash: Remove pte fragment dependency from nohash

Now that we have removed 64K page size support, the RCU page table free can
be much simpler for nohash. Make a copy of the the rcu callback to pgalloc.h
header similar to nohash 32. We could possibly merge 32 and 64 bit there. But
that is for a later patch

We also move the book3s specific handler to pgtable_book3s64.c. This will be
updated in a later patch to handle split pmd ptlock.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/book3e/64: Remove unsupported 64Kpage size from 64bit booke

We have in Kconfig

config PPC_64K_PAGES
bool "64k page size"
depends on !PPC_FSL_BOOK3E && (44x || PPC_BOOK3S_64 || PPC_BOOK3E_64)
select HAVE_ARCH_SOFT_DIRTY if PPC_BOOK3S_64

Only supported BOOK3E 64 bit platforms is FSL_BOOK3E. Remove the dead 64k page
support code from 64bit nohash.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm: Rename pte fragment functions

We rename the alloc and get_from_cache to indicate they operate on pte
fragments. In later patch we will add pmd fragment support.

No functional change in this patch.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm: Use pmd_lockptr instead of opencoding it

In later patch we switch pmd_lock from mm->page_table_lock to split pmd ptlock.
It avoid compilations issues, use pmd_lockptr helper.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

powerpc/mm/book3s64: Move book3s64 code to pgtable-book3s64

Only code movement and avoid #ifdef.

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Merge branch 'topic/ppc-kvm' into next

This brings in one commit that we may want to share with the kvm-ppc
tree, to avoid merge conflicts and get wider testing.

powerpc/kvm: Switch kvm pmd allocator to custom allocator

In the next set of patches, we will switch pmd allocator to use page fragments
and the locking will be updated to split pmd ptlock. We want to avoid using
fragments for partition-scoped table. Use slab cache similar to level 4 table

Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

cxl: Report the tunneled operations status

Failure to synchronize the tunneled operations does not prevent
the initialization of the cxl card. This patch reports the tunneled
operations status via /sys.

Signed-off-by: Philippe Bergheaud <felix@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>