pinctrl: sh-pfc: sh7269: Fix CAN function GPIOs

[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ]

pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.

A closer look reveals other issues:
  - Some functionality is available on alternative pins, but the
    PINMUX_DATA() entries is using the wrong marks,
  - Several configurations are missing.

Fix this by:
  - Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
    CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
    resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
    corresponding enum IDs,
  - Adding all missing enum IDs and marks,
  - Use the right (*_PJ2x) variants for alternative pins,
  - Adding all missing configurations to pinmux_data[],
  - Adding all missing function GPIO definitions to pinmux_func_gpios[].

See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
  [1] Table 1.4 List of Pins
  [2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
      Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
      (32 Mailboxes × 1 Channel),
  [3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
      One Channel (96 Mailboxes × 1 Channel),
  [4] Table 48.3 Multiplexed Pins (Port B),
  [5] Table 48.4 Multiplexed Pins (Port C),
  [6] Table 48.10 Multiplexed Pins (Port J),
  [7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>

PM / devfreq: rk3399_dmc: Add COMPILE_TEST and HAVE_ARM_SMCCC dependency

[ Upstream commit eff5d31f7407fa9d31fb840106f1593399457298 ]

To build test, add COMPILE_TEST depedency to both ARM_RK3399_DMC_DEVFREQ
and DEVFREQ_EVENT_ROCKCHIP_DFI configuration. And ARM_RK3399_DMC_DEVFREQ
used the SMCCC interface so that add HAVE_ARM_SMCCC dependency to prevent
the build break.

Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/vdso: Provide missing include file

[ Upstream commit bff47c2302cc249bcd550b17067f8dddbd4b6f77 ]

When building with C=1, sparse issues a warning:

  CHECK   arch/x86/entry/vdso/vdso32-setup.c
  arch/x86/entry/vdso/vdso32-setup.c:28:28: warning: symbol 'vdso32_enabled' was not declared. Should it be static?

Provide the missing header file.

Signed-off-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/36224.1575599767@turing-police
Signed-off-by: Sasha Levin <sashal@kernel.org>

crypto: chtls - Fixed memory leak

[ Upstream commit 93e23eb2ed6c11b4f483c8111ac155ec2b1f3042 ]

Freed work request skbs when connection terminates.
enqueue_wr()/ dequeue_wr() is shared between softirq
and application contexts, should be protected by socket
lock. Moved dequeue_wr() to appropriate file.

Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: imx-sdma: Fix memory leak

[ Upstream commit 02939cd167095f16328a1bd5cab5a90b550606df ]

The current descriptor is not on any list of the virtual DMA channel.
Once sdma_terminate_all() is called when a descriptor is currently
in flight then this one is forgotten to be freed. We have to call
vchan_terminate_vdesc() on this descriptor to re-add it to the lists.
Now that we also free the currently running descriptor we can (and
actually have to) remove the current descriptor from its list also
for the cyclic case.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Robin Gong <yibin.gong@nxp.com>
Tested-by: Robin Gong <yibin.gong@nxp.com>
Link: https://lore.kernel.org/r/20191216105328.15198-10-s.hauer@pengutronix.de
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

dmaengine: Store module owner in dma_device struct

[ Upstream commit dae7a589c18a4d979d5f14b09374e871b995ceb1 ]

dma_chan_to_owner() dereferences the driver from the struct device to
obtain the owner and call module_[get|put](). However, if the backing
device is unbound before the dma_device is unregistered, the driver
will be cleared and this will cause a NULL pointer dereference.

Instead, store a pointer to the owner module in the dma_device struct
so the module reference can be properly put when the channel is put, even
if the backing device was destroyed first.

This change helps to support a safer unbind of DMA engines.
If the dma_device is unregistered in the driver's remove function,
there's no guarantee that there are no existing clients and a users
action may trigger the WARN_ONCE in dma_async_device_unregister()
which is unlikely to leave the system in a consistent state.
Instead, a better approach is to allow the backing driver to go away
and fail any subsequent requests to it.

Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Link: https://lore.kernel.org/r/20191216190120.21374-2-logang@deltatee.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selinux: ensure we cleanup the internal AVC counters on error in avc_update()

[ Upstream commit 030b995ad9ece9fa2d218af4429c1c78c2342096 ]

In AVC update we don't call avc_node_kill() when avc_xperms_populate()
fails, resulting in the avc->avc_cache.active_nodes counter having a
false value.  In last patch this changes was missed , so correcting it.

Fixes: fa1aa143ac4a ("selinux: extended permissions for ioctls")
Signed-off-by: Jaihind Yadav <jaihindyadav@codeaurora.org>
Signed-off-by: Ravi Kumar Siddojigari <rsiddoji@codeaurora.org>
[PM: merge fuzz, minor description cleanup]
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: r8a7779: Add device node for ARM global timer

[ Upstream commit 8443ffd1bbd5be74e9b12db234746d12e8ea93e2 ]

Add a device node for the global timer, which is part of the Cortex-A9
MPCore.

The global timer can serve as an accurate (4 ns) clock source for
scheduling and delay loops.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191211135222.26770-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/mediatek: handle events when enabling/disabling crtc

[ Upstream commit 411f5c1eacfebb1f6e40b653d29447cdfe7282aa ]

The driver currently handles vblank events only when updating planes on
an already enabled CRTC. The atomic update API however allows requesting
an event when enabling or disabling a CRTC. This currently leads to
event objects being leaked in the kernel and to events not being sent
out. Fix it.

Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: aic7xxx: Adjust indentation in ahc_find_syncrate

[ Upstream commit 4dbc96ad65c45cdd4e895ed7ae4c151b780790c5 ]

Clang warns:

../drivers/scsi/aic7xxx/aic7xxx_core.c:2317:5: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
                        if ((syncrate->sxfr_u2 & ST_SXFR) != 0)
                        ^
../drivers/scsi/aic7xxx/aic7xxx_core.c:2310:4: note: previous statement
is here
                        if (syncrate == &ahc_syncrates[maxsync])
                        ^
1 warning generated.

This warning occurs because there is a space amongst the tabs on this
line. Remove it so that the indentation is consistent with the Linux kernel
coding style and clang no longer warns.

This has been a problem since the beginning of git history hence no fixes
tag.

Link: https://github.com/ClangBuiltLinux/linux/issues/817
Link: https://lore.kernel.org/r/20191218014220.52746-1-natechancellor@gmail.com
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ufs: Complete pending requests in host reset and restore path

[ Upstream commit 2df74b6985b51e77756e2e8faa16c45ca3ba53c5 ]

In UFS host reset and restore path, before probe, we stop and start the
host controller once. After host controller is stopped, the pending
requests, if any, are cleared from the doorbell, but no completion IRQ
would be raised due to the hba is stopped.  These pending requests shall be
completed along with the first NOP_OUT command (as it is the first command
which can raise a transfer completion IRQ) sent during probe.  Since the
OCSs of these pending requests are not SUCCESS (because they are not yet
literally finished), their UPIUs shall be dumped. When there are multiple
pending requests, the UPIU dump can be overwhelming and may lead to
stability issues because it is in atomic context.  Therefore, before probe,
complete these pending requests right after host controller is stopped and
silence the UPIU dump from them.

Link: https://lore.kernel.org/r/1574751214-8321-5-git-send-email-cang@qti.qualcomm.com
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
Tested-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Can Guo <cang@codeaurora.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ACPICA: Disassembler: create buffer fields in ACPI_PARSE_LOAD_PASS1

[ Upstream commit 5ddbd77181dfca61b16d2e2222382ea65637f1b9 ]

ACPICA commit 29cc8dbc5463a93625bed87d7550a8bed8913bf4

create_buffer_field is a deferred op that is typically processed in
load pass 2. However, disassembly of control method contents walk the
parse tree with ACPI_PARSE_LOAD_PASS1 and AML_CREATE operators are
processed in a later walk. This is a problem when there is a control
method that has the same name as the AML_CREATE object. In this case,
any use of the name segment will be detected as a method call rather
than a reference to a buffer field. If this is detected as a method
call, it can result in a mal-formed parse tree if the control methods
have parameters.

This change in processing AML_CREATE ops earlier solves this issue by
inserting the named object in the ACPI namespace so that references
to this name would be detected as a name string rather than a method
call.

Link: https://github.com/acpica/acpica/commit/29cc8dbc
Reported-by: Elia Geretto <elia.f.geretto@gmail.com>
Tested-by: Elia Geretto <elia.f.geretto@gmail.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Erik Kaneda <erik.kaneda@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

orinoco: avoid assertion in case of NULL pointer

[ Upstream commit c705f9fc6a1736dcf6ec01f8206707c108dca824 ]

In ezusb_init, if upriv is NULL, the code crashes. However, the caller
in ezusb_probe can handle the error and print the failure message.
The patch replaces the BUG_ON call to error return.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

rtlwifi: rtl_pci: Fix -Wcast-function-type

[ Upstream commit cb775c88da5d48a85d99d95219f637b6fad2e0e9 ]

correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20

Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iwlegacy: Fix -Wcast-function-type

[ Upstream commit da5e57e8a6a3e69dac2937ba63fa86355628fbb2 ]

correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20

Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipw2x00: Fix -Wcast-function-type

[ Upstream commit ebd77feb27e91bb5fe35a7818b7c13ea7435fb98 ]

correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20

Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

b43legacy: Fix -Wcast-function-type

[ Upstream commit 475eec112e4267232d10f4afe2f939a241692b6c ]

correct usage prototype of callback in tasklet_init().
Report by https://github.com/KSPP/linux/issues/20

Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Phong Tran <tranmanphong@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: usx2y: Adjust indentation in snd_usX2Y_hwdep_dsp_status

[ Upstream commit df4654bd6e42125d9b85ce3a26eaca2935290b98 ]

Clang warns:

../sound/usb/usx2y/usX2Yhwdep.c:122:3: warning: misleading indentation;
statement is not part of the previous 'if' [-Wmisleading-indentation]
        info->version = USX2Y_DRIVER_VERSION;
        ^
../sound/usb/usx2y/usX2Yhwdep.c:120:2: note: previous statement is here
        if (us428->chip_status & USX2Y_STAT_CHIP_INIT)
        ^
1 warning generated.

This warning occurs because there is a space before the tab on this
line. Remove it so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.

This was introduced before the beginning of git history so no fixes tag.

Link: https://github.com/ClangBuiltLinux/linux/issues/831
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20191218034257.54535-1-natechancellor@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nft_tunnel: add the missing ERSPAN_VERSION nla_policy

[ Upstream commit 0705f95c332081036d85f26691e9d3cd7d901c31 ]

ERSPAN_VERSION is an attribute parsed in kernel side, nla_policy
type should be added for it, like other attributes.

Fixes: af308b94a2a4 ("netfilter: nf_tables: add tunnel support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fore200e: Fix incorrect checks of NULL pointer dereference

[ Upstream commit bbd20c939c8aa3f27fa30e86691af250bf92973a ]

In fore200e_send and fore200e_close, the pointers from the arguments
are dereferenced in the variable declaration block and then checked
for NULL. The patch fixes these issues by avoiding NULL pointer
dereferences.

Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

r8169: check that Realtek PHY driver module is loaded

[ Upstream commit f325937735498afb054a0195291bbf68d0b60be5 ]

Some users complained about problems with r8169 and it turned out that
the generic PHY driver was used instead instead of the dedicated one.
In all cases reason was that r8169.ko was in initramfs, but realtek.ko
not. Manually adding realtek.ko to initramfs fixed the issues.
Root cause seems to be that tools like dracut and genkernel don't
consider softdeps. Add a check for loaded Realtek PHY driver module
and provide the user with a hint if it's not loaded.

Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

reiserfs: Fix spurious unlock in reiserfs_fill_super() error handling

[ Upstream commit 4d5c1adaf893b8aa52525d2b81995e949bcb3239 ]

When we fail to allocate string for journal device name we jump to
'error' label which tries to unlock reiserfs write lock which is not
held. Jump to 'error_unlocked' instead.

Fixes: f32485be8397 ("reiserfs: delay reiserfs lock until journal initialization")
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: v4l2-device.h: Explicitly compare grp{id,mask} to zero in v4l2_device macros

[ Upstream commit afb34781620274236bd9fc9246e22f6963ef5262 ]

When building with Clang + -Wtautological-constant-compare, several of
the ivtv and cx18 drivers warn along the lines of:

 drivers/media/pci/cx18/cx18-driver.c:1005:21: warning: converting the
 result of '<<' to a boolean always evaluates to true
 [-Wtautological-constant-compare]
                         cx18_call_hw(cx, CX18_HW_GPIO_RESET_CTRL,
                                         ^
 drivers/media/pci/cx18/cx18-cards.h:18:37: note: expanded from macro
 'CX18_HW_GPIO_RESET_CTRL'
 #define CX18_HW_GPIO_RESET_CTRL         (1 << 6)
                                           ^
 1 warning generated.

This warning happens because the shift operation is implicitly converted
to a boolean in v4l2_device_mask_call_all before being negated. This can
be solved by just comparing the mask result to 0 explicitly so that
there is no boolean conversion. The ultimate goal is to enable
-Wtautological-compare globally because there are several subwarnings
that would be helpful to have.

For visual consistency and avoidance of these warnings in the future,
all of the implicitly boolean conversions in the v4l2_device macros
are converted to explicit ones as well.

Link: https://github.com/ClangBuiltLinux/linux/issues/752
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Increase D3 delay for AMD Ryzen5/7 XHCI controllers

[ Upstream commit 3030df209aa8cf831b9963829bd9f94900ee8032 ]

On Asus UX434DA (AMD Ryzen7 3700U) and Asus X512DK (AMD Ryzen5 3500U), the
XHCI controller fails to resume from runtime suspend or s2idle, and USB
becomes unusable from that point.

  xhci_hcd 0000:03:00.4: Refused to change power state, currently in D3
  xhci_hcd 0000:03:00.4: enabling device (0000 -> 0002)
  xhci_hcd 0000:03:00.4: WARN: xHC restore state timeout
  xhci_hcd 0000:03:00.4: PCI post-resume error -110!
  xhci_hcd 0000:03:00.4: HC died; cleaning up

During suspend, a transition to D3cold is attempted, however the affected
platforms do not seem to cut the power to the PCI device when in this
state, so the device stays in D3hot.

Upon resume, the D3hot-to-D0 transition is successful only if the D3 delay
is increased to 20ms. The transition failure does not appear to be
detectable as a CRS condition. Add a PCI quirk to increase the delay on the
affected hardware.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=205587
Link: http://lkml.kernel.org/r/CAD8Lp47Vh69gQjROYG69=waJgL7hs1PwnLonL9+27S_TcRhixA@mail.gmail.com
Link: https://lore.kernel.org/r/20191127053836.31624-2-drake@endlessm.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: Add generic quirk for increasing D3hot delay

[ Upstream commit 62fe23df067715a21c4aef44068efe7ceaa8f627 ]

Separate the D3 delay increase functionality out of quirk_radeon_pm() into
its own function so that it can be shared with other quirks, including the
AMD Ryzen XHCI quirk that will be introduced in a followup commit.

Tweak the function name and message to indicate more clearly that the delay
relates to a D3hot-to-D0 transition.

Link: https://lore.kernel.org/r/20191127053836.31624-1-drake@endlessm.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: cx23885: Add support for AVerMedia CE310B

[ Upstream commit dc4cac67e13515835ed8081d510aa507aacb013b ]

The AVerMedia CE310B is a simple composite + S-Video + stereo audio
capture card, and uses only the CX23888 to perform all of these
functions.

I've tested both video inputs and the audio interface and confirmed that
they're all working. However, there are some issues:

* Sometimes when I switch inputs the video signal turns black and can't
  be recovered until the system is rebooted. I haven't been able to
  determine the cause of this behavior, nor have I found a solution to
  fix it or any workarounds other than rebooting.
* The card sometimes seems to have trouble syncing to the video signal,
  and some of the VBI data appears as noise at the top of the frame, but
  I assume that to be a result of my very noisy RF environment and the
  card's unshielded input traces rather than a configuration issue.

Signed-off-by: Forest Crossman <cyrozap@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

PCI: iproc: Apply quirk_paxc_bridge() for module as well as built-in

[ Upstream commit 574f29036fce385e28617547955dd6911d375025 ]

Previously quirk_paxc_bridge() was applied when the iproc driver was
built-in, but not when it was compiled as a module.

This happened because it was under #ifdef CONFIG_PCIE_IPROC_PLATFORM:
PCIE_IPROC_PLATFORM=y causes CONFIG_PCIE_IPROC_PLATFORM to be defined, but
PCIE_IPROC_PLATFORM=m causes CONFIG_PCIE_IPROC_PLATFORM_MODULE to be
defined.

Move quirk_paxc_bridge() to pcie-iproc.c and drop the #ifdef so the quirk
is always applied, whether iproc is built-in or a module.

[bhelgaas: commit log, move to pcie-iproc.c, not pcie-iproc-platform.c]
Link: https://lore.kernel.org/r/20191211174511.89713-1-wei.liu@kernel.org
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6: rdu2: Limit USBH1 to Full Speed

[ Upstream commit 6bb1e09c4c375db29770444f689f35f5cbe696bc ]

Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3

[ Upstream commit cd58a174e58649426fb43d7456e5f7d7eab58af1 ]

RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core

[ Upstream commit d026c96b25b7ce5df89526aad2df988d553edb4d ]

QUSB2 PHY on msm8996 doesn't work well when autosuspend by
dwc3 core using USB2PHYCFG register is enabled. One of the
issue seen is that PHY driver reports PLL lock failure and
fails phy_init() if dwc3 core has USB2 PHY suspend enabled.
Fix this by using quirks to disable USB2 PHY LPM/suspend and
dwc3 core already takes care of explicitly suspending PHY
during suspend if quirks are specified.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Link: https://lore.kernel.org/r/20191209151501.26993-1-p.pisati@gmail.com
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selinux: ensure we cleanup the internal AVC counters on error in avc_insert()

[ Upstream commit d8db60cb23e49a92cf8cada3297395c7fa50fdf8 ]

Fix avc_insert() to call avc_node_kill() if we've already allocated
an AVC node and the code fails to insert the node in the cache.

Fixes: fa1aa143ac4a ("selinux: extended permissions for ioctls")
Reported-by: rsiddoji@codeaurora.org
Suggested-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm: dts: allwinner: H3: Add PMU node

[ Upstream commit 0388a110747bec0c9d9de995842bb2a03a26aae1 ]

Add the Performance Monitoring Unit (PMU) device tree node to the H3
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.

Tested with perf record and taskset on an OrangePi Zero.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: allwinner: H6: Add PMU mode

[ Upstream commit 7aa9b9eb7d6a8fde7acbe0446444f7e3fae1fe3b ]

Add the Performance Monitoring Unit (PMU) device tree node to the H6
.dtsi, which tells DT users which interrupts are triggered by PMU
overflow events on each core. The numbers come from the manual and have
been checked in U-Boot and with perf in Linux.

Tested with perf record and taskset on a Pine H64.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>

selinux: fall back to ref-walk if audit is required

[ Upstream commit 0188d5c025ca8fe756ba3193bd7d150139af5a88 ]

commit bda0be7ad994 ("security: make inode_follow_link RCU-walk aware")
passed down the rcu flag to the SELinux AVC, but failed to adjust the
test in slow_avc_audit() to also return -ECHILD on LSM_AUDIT_DATA_DENTRY.
Previously, we only returned -ECHILD if generating an audit record with
LSM_AUDIT_DATA_INODE since this was only relevant from inode_permission.
Move the handling of MAY_NOT_BLOCK to avc_audit() and its inlined
equivalent in selinux_inode_permission() immediately after we determine
that audit is required, and always fall back to ref-walk in this case.

Fixes: bda0be7ad994 ("security: make inode_follow_link RCU-walk aware")
Reported-by: Will Deacon <will@kernel.org>
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFC: port100: Convert cpu_to_le16(le16_to_cpu(E1) + E2) to use le16_add_cpu().

[ Upstream commit 718eae277e62a26e5862eb72a830b5e0fe37b04a ]

Convert cpu_to_le16(le16_to_cpu(frame->datalen) + len) to
use le16_add_cpu(), which is more concise and does the same thing.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/wan/fsl_ucc_hdlc: reject muram offsets above 64K

[ Upstream commit 148587a59f6b85831695e0497d9dd1af5f0495af ]

Qiang Zhao points out that these offsets get written to 16-bit
registers, and there are some QE platforms with more than 64K
muram. So it is possible that qe_muram_alloc() gives us an allocation
that can't actually be used by the hardware, so detect and reject
that.

Reported-by: Qiang Zhao <qiang.zhao@nxp.com>
Reviewed-by: Timur Tabi <timur@kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

regulator: rk808: Lower log level on optional GPIOs being not available

[ Upstream commit b8a039d37792067c1a380dc710361905724b9b2f ]

RK808 can leverage a couple of GPIOs to tweak the ramp rate during DVS
(Dynamic Voltage Scaling). These GPIOs are entirely optional but a
dev_warn() appeared when cleaning this driver to use a more up-to-date
gpiod API. At least reduce the log level to 'info' as it is totally
fine to not populate these GPIO on a hardware design.

This change is trivial but it is worth not polluting the logs during
bringup phase by having real warnings and errors sorted out
correctly.

Fixes: a13eaf02e2d6 ("regulator: rk808: make better use of the gpiod API")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20191203164709.11127-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: Ensure ret is always initialized when using SOC15_WAIT_ON_RREG

[ Upstream commit a63141e31764f8daf3f29e8e2d450dcf9199d1c8 ]

Commit b0f3cd3191cd ("drm/amdgpu: remove unnecessary JPEG2.0 code from
VCN2.0") introduced a new clang warning in the vcn_v2_0_stop function:

../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: warning: variable 'r'
is used uninitialized whenever 'while' loop exits because its condition
is false [-Wsometimes-uninitialized]
        SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
                while ((tmp_ & (mask)) != (expected_value)) {   \
                       ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1083:6: note: uninitialized use
occurs here
        if (r)
            ^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1082:2: note: remove the
condition if it is always true
        SOC15_WAIT_ON_RREG(VCN, 0, mmUVD_STATUS, UVD_STATUS__IDLE, 0x7, r);
        ^
../drivers/gpu/drm/amd/amdgpu/../amdgpu/soc15_common.h:55:10: note:
expanded from macro 'SOC15_WAIT_ON_RREG'
                while ((tmp_ & (mask)) != (expected_value)) {   \
                       ^
../drivers/gpu/drm/amd/amdgpu/vcn_v2_0.c:1072:7: note: initialize the
variable 'r' to silence this warning
        int r;
             ^
              = 0
1 warning generated.

To prevent warnings like this from happening in the future, make the
SOC15_WAIT_ON_RREG macro initialize its ret variable before the while
loop that can time out. This macro's return value is always checked so
it should set ret in both the success and fail path.

Link: https://github.com/ClangBuiltLinux/linux/issues/776
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: remove 4 set but not used variable in amdgpu_atombios_get_connector_info_from_object_table

[ Upstream commit bae028e3e521e8cb8caf2cc16a455ce4c55f2332 ]

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c: In function
'amdgpu_atombios_get_connector_info_from_object_table':
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:26: warning: variable
'grph_obj_num' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:376:13: warning: variable
'grph_obj_id' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:37: warning: variable
'con_obj_type' set but not used [-Wunused-but-set-variable]
drivers/gpu/drm/amd/amdgpu/amdgpu_atombios.c:341:24: warning: variable
'con_obj_num' set but not used [-Wunused-but-set-variable]

They are never used, so can be removed.

Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Signed-off-by: yu kuai <yukuai3@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: qcom: rcg2: Don't crash if our parent can't be found; return an error

[ Upstream commit 908b050114d8fefdddc57ec9fbc213c3690e7f5f ]

When I got my clock parenting slightly wrong I ended up with a crash
that looked like this:

  Unable to handle kernel NULL pointer dereference at virtual
  address 0000000000000000
  ...
  pc : clk_hw_get_rate+0x14/0x44
  ...
  Call trace:
   clk_hw_get_rate+0x14/0x44
   _freq_tbl_determine_rate+0x94/0xfc
   clk_rcg2_determine_rate+0x2c/0x38
   clk_core_determine_round_nolock+0x4c/0x88
   clk_core_round_rate_nolock+0x6c/0xa8
   clk_core_round_rate_nolock+0x9c/0xa8
   clk_core_set_rate_nolock+0x70/0x180
   clk_set_rate+0x3c/0x6c
   of_clk_set_defaults+0x254/0x360
   platform_drv_probe+0x28/0xb0
   really_probe+0x120/0x2dc
   driver_probe_device+0x64/0xfc
   device_driver_attach+0x4c/0x6c
   __driver_attach+0xac/0xc0
   bus_for_each_dev+0x84/0xcc
   driver_attach+0x2c/0x38
   bus_add_driver+0xfc/0x1d0
   driver_register+0x64/0xf8
   __platform_driver_register+0x4c/0x58
   msm_drm_register+0x5c/0x60
   ...

It turned out that clk_hw_get_parent_by_index() was returning NULL and
we weren't checking.  Let's check it so that we don't crash.

Fixes: ac269395cdd8 ("clk: qcom: Convert to clk_hw based provider APIs")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.1.I7487325fe8e701a68a07d3be8a6a4b571eca9cfa@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kconfig: fix broken dependency in randconfig-generated .config

[ Upstream commit c8fb7d7e48d11520ad24808cfce7afb7b9c9f798 ]

Running randconfig on arm64 using KCONFIG_SEED=0x40C5E904 (e.g. on v5.5)
produces the .config with CONFIG_EFI=y and CONFIG_CPU_BIG_ENDIAN=y,
which does not meet the !CONFIG_CPU_BIG_ENDIAN dependency.

This is because the user choice for CONFIG_CPU_LITTLE_ENDIAN vs
CONFIG_CPU_BIG_ENDIAN is set by randomize_choice_values() after the
value of CONFIG_EFI is calculated.

When this happens, the has_changed flag should be set.

Currently, it takes the result from the last iteration. It should
accumulate all the results of the loop.

Fixes: 3b9a19e08960 ("kconfig: loop as long as we changed some symbols in randconfig")
Reported-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: s390: ENOTSUPP -> EOPNOTSUPP fixups

[ Upstream commit c611990844c28c61ca4b35ff69d3a2ae95ccd486 ]

There is no ENOTSUPP for userspace.

Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Fixes: 519783935451 ("KVM: s390: introduce ais mode modify function")
Fixes: 2c1a48f2e5ed ("KVM: S390: add new group for flic")
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nbd: add a flush_workqueue in nbd_start_device

[ Upstream commit 5c0dd228b5fc30a3b732c7ae2657e0161ec7ed80 ]

When kzalloc fail, may cause trying to destroy the
workqueue from inside the workqueue.

If num_connections is m (2 < m), and NO.1 ~ NO.n
(1 < n < m) kzalloc are successful. The NO.(n + 1)
failed. Then, nbd_start_device will return ENOMEM
to nbd_start_device_ioctl, and nbd_start_device_ioctl
will return immediately without running flush_workqueue.
However, we still have n recv threads. If nbd_release
run first, recv threads may have to drop the last
config_refs and try to destroy the workqueue from
inside the workqueue.

To fix it, add a flush_workqueue in nbd_start_device.

Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs")
Signed-off-by: Sun Ke <sunke32@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Retrain dongles when SINK_COUNT becomes non-zero

[ Upstream commit 3eb6d7aca53d81ce888624f09cd44dc0302161e8 ]

[WHY]
Two years ago the patch referenced by the Fixes tag stopped running
dp_verify_link_cap_with_retries during DP detection when the reason
for the detection was a short-pulse interrupt. This effectively meant
that we were no longer doing the verify_link_cap training on active
dongles when their SINK_COUNT changed from 0 to 1.

A year ago this was partly remedied with:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")

This made sure that we trained the dongle on initial hotplug (without
connected downstream devices).

This is all fine and dandy if it weren't for the fact that there are
some dongles on the market that don't like link training when SINK_COUNT
is 0 These dongles will in fact indicate a SINK_COUNT of 0 immediately
after hotplug, even when a downstream device is connected, and then
trigger a shortpulse interrupt indicating a SINK_COUNT change to 1.

In order to play nicely we will need our policy to not link train an
active DP dongle when SINK_COUNT is 0 but ensure we train it when the
SINK_COUNT changes to 1.

[HOW]
Call dp_verify_link_cap_with_retries on detection even when the detection
is triggered from a short pulse interrupt.

With this change we can also revert this commit which we'll do in a separate
follow-up change:
commit 80adaebd2d41 ("drm/amd/display: Don't skip link training for empty dongle")

Fixes: 0301ccbaf67d ("drm/amd/display: DP Compliance 400.1.1 failure")
Suggested-by: Louis Li <Ching-shih.Li@amd.com>
Tested-by: Louis Li <Ching-shih.Li@amd.com>
Cc: Wenjing Liu <Wenjing.Liu@amd.com>
Cc: Hersen Wu <hersenxs.wu@amd.com>
Cc: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ath10k: Correct the DMA direction for management tx buffers

[ Upstream commit 6ba8b3b6bd772f575f7736c8fd893c6981fcce16 ]

The management packets, send to firmware via WMI, are
mapped using the direction DMA_TO_DEVICE. Currently in
case of wmi cleanup, these buffers are being unmapped
using an incorrect DMA direction. This can cause unwanted
behavior when the host driver is handling a restart
of the wlan firmware.

We might see a trace like below

[<ffffff8008098b18>] __dma_inv_area+0x28/0x58
[<ffffff8001176734>] ath10k_wmi_mgmt_tx_clean_up_pending+0x60/0xb0 [ath10k_core]
[<ffffff80088c7c50>] idr_for_each+0x78/0xe4
[<ffffff80011766a4>] ath10k_wmi_detach+0x4c/0x7c [ath10k_core]
[<ffffff8001163d7c>] ath10k_core_stop+0x58/0x68 [ath10k_core]
[<ffffff800114fb74>] ath10k_halt+0xec/0x13c [ath10k_core]
[<ffffff8001165110>] ath10k_core_restart+0x11c/0x1a8 [ath10k_core]
[<ffffff80080c36bc>] process_one_work+0x16c/0x31c

Fix the incorrect DMA direction during the wmi
management tx buffer cleanup.

Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1

Fixes: dc405152bb6 ("ath10k: handle mgmt tx completion event")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4, jbd2: ensure panic when aborting with zero errno

[ Upstream commit 51f57b01e4a3c7d7bdceffd84de35144e8c538e7 ]

JBD2_REC_ERR flag used to indicate the errno has been updated when jbd2
aborted, and then __ext4_abort() and ext4_handle_error() can invoke
panic if ERRORS_PANIC is specified. But if the journal has been aborted
with zero errno, jbd2_journal_abort() didn't set this flag so we can
no longer panic. Fix this by always record the proper errno in the
journal superblock.

Fixes: 4327ba52afd03 ("ext4, jbd2: ensure entering into panic after recording an error in superblock")
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20191204124614.45424-3-yi.zhang@huawei.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 8952/1: Disable kmemleak on XIP kernels

[ Upstream commit bc420c6ceefbb86cbbc8c00061bd779c17fa6997 ]

Kmemleak relies on specific symbols to register the read only data
during init (e.g. __start_ro_after_init).
Trying to build an XIP kernel on arm results in the linking error
reported below because when this option is selected read only data
after init are not allowed since .data is read only (.rodata).

  arm-linux-gnueabihf-ld: mm/kmemleak.o: in function `kmemleak_init':
  kmemleak.c:(.init.text+0x148): undefined reference to `__end_ro_after_init'
  arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x14c):
     undefined reference to `__end_ro_after_init'
  arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x150):
     undefined reference to `__start_ro_after_init'
  arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x156):
     undefined reference to `__start_ro_after_init'
  arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x162):
     undefined reference to `__start_ro_after_init'
  arm-linux-gnueabihf-ld: kmemleak.c:(.init.text+0x16a):
     undefined reference to `__start_ro_after_init'
  linux/Makefile:1078: recipe for target 'vmlinux' failed

Fix the issue enabling kmemleak only on non XIP kernels.

Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Fix very unlikely race of registering two stat tracers

[ Upstream commit dfb6cd1e654315168e36d947471bd2a0ccd834ae ]

Looking through old emails in my INBOX, I came across a patch from Luis
Henriques that attempted to fix a race of two stat tracers registering the
same stat trace (extremely unlikely, as this is done in the kernel, and
probably doesn't even exist). The submitted patch wasn't quite right as it
needed to deal with clean up a bit better (if two stat tracers were the
same, it would have the same files).

But to make the code cleaner, all we needed to do is to keep the
all_stat_sessions_mutex held for most of the registering function.

Link: http://lkml.kernel.org/r/1410299375-20068-1-git-send-email-luis.henriques@canonical.com
Fixes: 002bb86d8d42f ("tracing/ftrace: separate events tracing and stats tracing engine")
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

tracing: Fix tracing_stat return values in error handling paths

[ Upstream commit afccc00f75bbbee4e4ae833a96c2d29a7259c693 ]

tracing_stat_init() was always returning '0', even on the error paths.  It
now returns -ENODEV if tracing_init_dentry() fails or -ENOMEM if it fails
to created the 'trace_stat' debugfs directory.

Link: http://lkml.kernel.org/r/1410299381-20108-1-git-send-email-luis.henriques@canonical.com
Fixes: ed6f1c996bfe4 ("tracing: Check return value of tracing_init_dentry()")
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>
[ Pulled from the archeological digging of my INBOX ]
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/iov: Move VF pdev fixup into pcibios_fixup_iov()

[ Upstream commit 965c94f309be58fbcc6c8d3e4f123376c5970d79 ]

An ioda_pe for each VF is allocated in pnv_pci_sriov_enable() before
the pci_dev for the VF is created. We need to set the pe->pdev pointer
at some point after the pci_dev is created. Currently we do that in:

pcibios_bus_add_device()
pnv_pci_dma_dev_setup() (via phb->ops.dma_dev_setup)
/* fixup is done here */
pnv_pci_ioda_dma_dev_setup() (via pnv_phb->dma_dev_setup)

The fixup needs to be done before setting up DMA for for the VF's PE,
but there's no real reason to delay it until this point. Move the
fixup into pnv_pci_ioda_fixup_iov() so the ordering is:

pcibios_add_device()
pnv_pci_ioda_fixup_iov() (via ppc_md.pcibios_fixup_sriov)

pcibios_bus_add_device()
...

This isn't strictly required, but it's a slightly more logical place
to do the fixup and it simplifies pnv_pci_dma_dev_setup().

Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200110070207.439-4-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/pci: Fix possible deadlock in recover_store()

[ Upstream commit 576c75e36c689bec6a940e807bae27291ab0c0de ]

With zpci_disable() working, lockdep detected a potential deadlock
(lockdep output at the end).

The deadlock is between recovering a PCI function via the

/sys/bus/pci/devices/<dev>/recover

attribute vs powering it off via

/sys/bus/pci/slots/<slot>/power.

The fix is analogous to the changes in commit 0ee223b2e1f6 ("scsi: core:
Avoid that SCSI device removal through sysfs triggers a deadlock")
that fixed a potential deadlock on removing a SCSI device via sysfs.

[  204.830107] ======================================================
[  204.830109] WARNING: possible circular locking dependency detected
[  204.830111] 5.5.0-rc2-06072-gbc03ecc9a672 #6 Tainted: G        W
[  204.830112] ------------------------------------------------------
[  204.830113] bash/1034 is trying to acquire lock:
[  204.830115] 0000000192a1a610 (kn->count#200){++++}, at: kernfs_remove_by_name_ns+0x5c/0xa8
[  204.830122]
               but task is already holding lock:
[  204.830123] 00000000c16134a8 (pci_rescan_remove_lock){+.+.}, at: pci_stop_and_remove_bus_device_locked+0x26/0x48
[  204.830128]
               which lock already depends on the new lock.

[  204.830129]
               the existing dependency chain (in reverse order) is:
[  204.830130]
               -> #1 (pci_rescan_remove_lock){+.+.}:
[  204.830134]        validate_chain+0x93a/0xd08
[  204.830136]        __lock_acquire+0x4ae/0x9d0
[  204.830137]        lock_acquire+0x114/0x280
[  204.830140]        __mutex_lock+0xa2/0x960
[  204.830142]        mutex_lock_nested+0x32/0x40
[  204.830145]        recover_store+0x4c/0xa8
[  204.830147]        kernfs_fop_write+0xe6/0x218
[  204.830151]        vfs_write+0xb0/0x1b8
[  204.830152]        ksys_write+0x6c/0xf8
[  204.830154]        system_call+0xd8/0x2d8
[  204.830155]
               -> #0 (kn->count#200){++++}:
[  204.830187]        check_noncircular+0x1e6/0x240
[  204.830189]        check_prev_add+0xfc/0xdb0
[  204.830190]        validate_chain+0x93a/0xd08
[  204.830192]        __lock_acquire+0x4ae/0x9d0
[  204.830193]        lock_acquire+0x114/0x280
[  204.830194]        __kernfs_remove.part.0+0x2e4/0x360
[  204.830196]        kernfs_remove_by_name_ns+0x5c/0xa8
[  204.830198]        remove_files.isra.0+0x4c/0x98
[  204.830199]        sysfs_remove_group+0x66/0xc8
[  204.830201]        sysfs_remove_groups+0x46/0x68
[  204.830204]        device_remove_attrs+0x52/0x90
[  204.830207]        device_del+0x182/0x418
[  204.830208]        pci_remove_bus_device+0x8a/0x130
[  204.830210]        pci_stop_and_remove_bus_device_locked+0x3a/0x48
[  204.830212]        disable_slot+0x68/0x100
[  204.830213]        power_write_file+0x7c/0x130
[  204.830215]        kernfs_fop_write+0xe6/0x218
[  204.830217]        vfs_write+0xb0/0x1b8
[  204.830218]        ksys_write+0x6c/0xf8
[  204.830220]        system_call+0xd8/0x2d8
[  204.830221]
               other info that might help us debug this:

[  204.830223]  Possible unsafe locking scenario:

[  204.830224]        CPU0                    CPU1
[  204.830225]        ----                    ----
[  204.830226]   lock(pci_rescan_remove_lock);
[  204.830227]                                lock(kn->count#200);
[  204.830229]                                lock(pci_rescan_remove_lock);
[  204.830231]   lock(kn->count#200);
[  204.830233]
                *** DEADLOCK ***

[  204.830234] 4 locks held by bash/1034:
[  204.830235]  #0: 00000001b6fbc498 (sb_writers#4){.+.+}, at: vfs_write+0x158/0x1b8
[  204.830239]  #1: 000000018c9f5090 (&of->mutex){+.+.}, at: kernfs_fop_write+0xaa/0x218
[  204.830242]  #2: 00000001f7da0810 (kn->count#235){.+.+}, at: kernfs_fop_write+0xb6/0x218
[  204.830245]  #3: 00000000c16134a8 (pci_rescan_remove_lock){+.+.}, at: pci_stop_and_remove_bus_device_locked+0x26/0x48
[  204.830248]
               stack backtrace:
[  204.830250] CPU: 2 PID: 1034 Comm: bash Tainted: G        W         5.5.0-rc2-06072-gbc03ecc9a672 #6
[  204.830252] Hardware name: IBM 8561 T01 703 (LPAR)
[  204.830253] Call Trace:
[  204.830257]  [<00000000c05e10c0>] show_stack+0x88/0xf0
[  204.830260]  [<00000000c112dca4>] dump_stack+0xa4/0xe0
[  204.830261]  [<00000000c0694c06>] check_noncircular+0x1e6/0x240
[  204.830263]  [<00000000c0695bec>] check_prev_add+0xfc/0xdb0
[  204.830264]  [<00000000c06971da>] validate_chain+0x93a/0xd08
[  204.830266]  [<00000000c06994c6>] __lock_acquire+0x4ae/0x9d0
[  204.830267]  [<00000000c069867c>] lock_acquire+0x114/0x280
[  204.830269]  [<00000000c09ca15c>] __kernfs_remove.part.0+0x2e4/0x360
[  204.830270]  [<00000000c09cb5c4>] kernfs_remove_by_name_ns+0x5c/0xa8
[  204.830272]  [<00000000c09cee14>] remove_files.isra.0+0x4c/0x98
[  204.830274]  [<00000000c09cf2ae>] sysfs_remove_group+0x66/0xc8
[  204.830276]  [<00000000c09cf356>] sysfs_remove_groups+0x46/0x68
[  204.830278]  [<00000000c0e3dfe2>] device_remove_attrs+0x52/0x90
[  204.830280]  [<00000000c0e40382>] device_del+0x182/0x418
[  204.830281]  [<00000000c0dcfd7a>] pci_remove_bus_device+0x8a/0x130
[  204.830283]  [<00000000c0dcfe92>] pci_stop_and_remove_bus_device_locked+0x3a/0x48
[  204.830285]  [<00000000c0de7190>] disable_slot+0x68/0x100
[  204.830286]  [<00000000c0de6514>] power_write_file+0x7c/0x130
[  204.830288]  [<00000000c09cc846>] kernfs_fop_write+0xe6/0x218
[  204.830290]  [<00000000c08f3480>] vfs_write+0xb0/0x1b8
[  204.830291]  [<00000000c08f378c>] ksys_write+0x6c/0xf8
[  204.830293]  [<00000000c1154374>] system_call+0xd8/0x2d8
[  204.830294] INFO: lockdep is turned off.

Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pwm: omap-dmtimer: Simplify error handling

[ Upstream commit c4cf7aa57eb83b108d2d9c6c37c143388fee2a4d ]

Instead of doing error handling in the middle of ->probe(), move error
handling and freeing the reference to timer to the end.

This fixes a resource leak as dm_timer wasn't freed when allocating
*omap failed.

Implementation note: The put: label was never reached without a goto and
ret being unequal to 0, so the removed return statement is fine.

Fixes: 6604c6556db9 ("pwm: Add PWM driver for OMAP using dual-mode timers")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/sysfb: Fix check for bad VRAM size

[ Upstream commit dacc9092336be20b01642afe1a51720b31f60369 ]

When checking whether the reported lfb_size makes sense, the height
* stride result is page-aligned before seeing whether it exceeds the
reported size.

This doesn't work if height * stride is not an exact number of pages.
For example, as reported in the kernel bugzilla below, an 800x600x32 EFI
framebuffer gets skipped because of this.

Move the PAGE_ALIGN to after the check vs size.

Reported-by: Christopher Head <chead@chead.ca>
Tested-by: Christopher Head <chead@chead.ca>
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206051
Link: https://lkml.kernel.org/r/20200107230410.2291947-1-nivedita@alum.mit.edu
Signed-off-by: Sasha Levin <sashal@kernel.org>

jbd2: clear JBD2_ABORT flag before journal_reset to update log tail info when load journal

[ Upstream commit a09decff5c32060639a685581c380f51b14e1fc2 ]

If the journal is dirty when the filesystem is mounted, jbd2 will replay
the journal but the journal superblock will not be updated by
journal_reset() because JBD2_ABORT flag is still set (it was set in
journal_init_common()). This is problematic because when a new transaction
is then committed, it will be recorded in block 1 (journal->j_tail was set
to 1 in journal_reset()). If unclean shutdown happens again before the
journal superblock is updated, the new recorded transaction will not be
replayed during the next mount (because of stale sb->s_start and
sb->s_sequence values) which can lead to filesystem corruption.

Fixes: 85e0c4e89c1b ("jbd2: if the journal is aborted then don't allow update of the log tail")
Signed-off-by: Kai Li <li.kai4@h3c.com>
Link: https://lore.kernel.org/r/20200111022542.5008-1-li.kai4@h3c.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kselftest: Minimise dependency of get_size on C library interfaces

[ Upstream commit 6b64a650f0b2ae3940698f401732988699eecf7a ]

It was observed[1] on arm64 that __builtin_strlen led to an infinite
loop in the get_size selftest.  This is because __builtin_strlen (and
other builtins) may sometimes result in a call to the C library
function.  The C library implementation of strlen uses an IFUNC
resolver to load the most efficient strlen implementation for the
underlying machine and hence has a PLT indirection even for static
binaries.  Because this binary avoids the C library startup routines,
the PLT initialization never happens and hence the program gets stuck
in an infinite loop.

On x86_64 the __builtin_strlen just happens to expand inline and avoid
the call but that is not always guaranteed.

Further, while testing on x86_64 (Fedora 31), it was observed that the
test also failed with a segfault inside write() because the generated
code for the write function in glibc seems to access TLS before the
syscall (probably due to the cancellation point check) and fails
because TLS is not initialised.

To mitigate these problems, this patch reduces the interface with the
C library to just the syscall function.  The syscall function still
sets errno on failure, which is undesirable but for now it only
affects cases where syscalls fail.

[1] https://bugs.linaro.org/show_bug.cgi?id=5479

Signed-off-by: Siddhesh Poyarekar <siddhesh@gotplt.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Tim Bird <tim.bird@sony.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clocksource/drivers/bcm2835_timer: Fix memory leak of timer

[ Upstream commit 2052d032c06761330bca4944bb7858b00960e868 ]

Currently when setup_irq fails the error exit path will leak the
recently allocated timer structure.  Originally the code would
throw a panic but a later commit changed the behaviour to return
via the err_iounmap path and hence we now have a memory leak. Fix
this by adding a err_timer_free error path that kfree's timer.

Addresses-Coverity: ("Resource Leak")
Fixes: 524a7f08983d ("clocksource/drivers/bcm2835_timer: Convert init function to return error")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20191219213246.34437-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: dwc2: Fix IN FIFO allocation

[ Upstream commit 644139f8b64d818f6345351455f14471510879a5 ]

On chips with fewer FIFOs than endpoints (for example RK3288 which has 9
endpoints, but only 6 which are cabable of input), the DPTXFSIZN
registers above the FIFO count may return invalid values.

With logging added on startup, I see:

dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=1 sz=256
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=2 sz=128
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=3 sz=128
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=4 sz=64
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=5 sz=64
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=6 sz=32
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=7 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=8 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=9 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=10 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=11 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=12 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=13 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=14 sz=0
dwc2 ff580000.usb: dwc2_hsotg_init_fifo: ep=15 sz=0

but:

# cat /sys/kernel/debug/ff580000.usb/fifo
Non-periodic FIFOs:
RXFIFO: Size 275
NPTXFIFO: Size 16, Start 0x00000113

Periodic TXFIFOs:
DPTXFIFO 1: Size 256, Start 0x00000123
DPTXFIFO 2: Size 128, Start 0x00000223
DPTXFIFO 3: Size 128, Start 0x000002a3
DPTXFIFO 4: Size 64, Start 0x00000323
DPTXFIFO 5: Size 64, Start 0x00000363
DPTXFIFO 6: Size 32, Start 0x000003a3
DPTXFIFO 7: Size 0, Start 0x000003e3
DPTXFIFO 8: Size 0, Start 0x000003a3
DPTXFIFO 9: Size 256, Start 0x00000123

so it seems that FIFO 9 is mirroring FIFO 1.

Fix the allocation by using the FIFO count instead of the endpoint count
when selecting a FIFO for an endpoint.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

usb: gadget: udc: fix possible sleep-in-atomic-context bugs in gr_probe()

[ Upstream commit 9c1ed62ae0690dfe5d5e31d8f70e70a95cb48e52 ]

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

drivers/usb/gadget/udc/core.c, 1175:
kzalloc(GFP_KERNEL) in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe

drivers/usb/gadget/udc/core.c, 1195:
mutex_lock in usb_add_gadget_udc_release
drivers/usb/gadget/udc/core.c, 1272:
usb_add_gadget_udc_release in usb_add_gadget_udc
drivers/usb/gadget/udc/gr_udc.c, 2186:
usb_add_gadget_udc in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
spin_lock in gr_probe

drivers/usb/gadget/udc/gr_udc.c, 212:
debugfs_create_file in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2197:
gr_dfs_create in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
    spin_lock in gr_probe

drivers/usb/gadget/udc/gr_udc.c, 2114:
devm_request_threaded_irq in gr_request_irq
drivers/usb/gadget/udc/gr_udc.c, 2202:
gr_request_irq in gr_probe
drivers/usb/gadget/udc/gr_udc.c, 2183:
    spin_lock in gr_probe

kzalloc(GFP_KERNEL), mutex_lock(), debugfs_create_file() and
devm_request_threaded_irq() can sleep at runtime.

To fix these possible bugs, usb_add_gadget_udc(), gr_dfs_create() and
gr_request_irq() are called without handling the spinlock.

These bugs are found by a static analysis tool STCheck written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

uio: fix a sleep-in-atomic-context bug in uio_dmem_genirq_irqcontrol()

[ Upstream commit b74351287d4bd90636c3f48bc188c2f53824c2d4 ]

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

kernel/irq/manage.c, 523:
synchronize_irq in disable_irq
drivers/uio/uio_dmem_genirq.c, 140:
disable_irq in uio_dmem_genirq_irqcontrol
drivers/uio/uio_dmem_genirq.c, 134:
_raw_spin_lock_irqsave in uio_dmem_genirq_irqcontrol

synchronize_irq() can sleep at runtime.

To fix this bug, disable_irq() is called without holding the spinlock.

This bug is found by a static analysis tool STCheck written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218094405.6009-1-baijiaju1990@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sparc: Add .exit.data section.

[ Upstream commit 548f0b9a5f4cffa0cecf62eb12aa8db682e4eee6 ]

This fixes build errors of all sorts.

Also, emit .exit.text unconditionally.

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

MIPS: Loongson: Fix potential NULL dereference in loongson3_platform_init()

[ Upstream commit 72d052e28d1d2363f9107be63ef3a3afdea6143c ]

If kzalloc fails, it should return -ENOMEM, otherwise may trigger a NULL
pointer dereference.

Fixes: 3adeb2566b9b ("MIPS: Loongson: Improve LEFI firmware interface")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

efi/x86: Map the entire EFI vendor string before copying it

[ Upstream commit ffc2760bcf2dba0dbef74013ed73eea8310cc52c ]

Fix a couple of issues with the way we map and copy the vendor string:
- we map only 2 bytes, which usually works since you get at least a
  page, but if the vendor string happens to cross a page boundary,
  a crash will result
- only call early_memunmap() if early_memremap() succeeded, or we will
  call it with a NULL address which it doesn't like,
- while at it, switch to early_memremap_ro(), and array indexing rather
  than pointer dereferencing to read the CHAR16 characters.

Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Matthew Garrett <mjg59@google.com>
Cc: linux-efi@vger.kernel.org
Fixes: 5b83683f32b1 ("x86: EFI runtime service support")
Link: https://lkml.kernel.org/r/20200103113953.9571-5-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins

[ Upstream commit a23680594da7a9e2696dbcf4f023e9273e2fa40b ]

Suspending Goodix touchscreens requires changing the interrupt pin to
output before sending them a power-down command. Followed by wiggling
the interrupt pin to wake the device up, after which it is put back
in input mode.

On Bay Trail devices with a Goodix touchscreen direct-irq mode is used
in combination with listing the pin as a normal GpioIo resource.

This works fine, until the goodix driver gets rmmod-ed and then insmod-ed
again. In this case byt_gpio_disable_free() calls
byt_gpio_clear_triggering() which clears the IRQ flags and after that the
(direct) IRQ no longer triggers.

This commit fixes this by adding a check for the BYT_DIRECT_IRQ_EN flag
to byt_gpio_clear_triggering().

Note that byt_gpio_clear_triggering() only gets called from
byt_gpio_disable_free() for direct-irq enabled pins, as these are excluded
from the irq_valid mask by byt_init_irq_valid_mask().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: sti: bdisp: fix a possible sleep-in-atomic-context bug in bdisp_device_run()

[ Upstream commit bb6d42061a05d71dd73f620582d9e09c8fbf7f5b ]

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

drivers/media/platform/sti/bdisp/bdisp-hw.c, 385:
    msleep in bdisp_hw_reset
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 341:
    bdisp_hw_reset in bdisp_device_run
drivers/media/platform/sti/bdisp/bdisp-v4l2.c, 317:
    _raw_spin_lock_irqsave in bdisp_device_run

To fix this bug, msleep() is replaced with udelay().

This bug is found by a static analysis tool STCheck written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

char/random: silence a lockdep splat with printk()

[ Upstream commit 1b710b1b10eff9d46666064ea25f079f70bc67a8 ]

Sergey didn't like the locking order,

uart_port->lock  ->  tty_port->lock

uart_write (uart_port->lock)
  __uart_start
    pl011_start_tx
      pl011_tx_chars
        uart_write_wakeup
          tty_port_tty_wakeup
            tty_port_default
              tty_port_tty_get (tty_port->lock)

but those code is so old, and I have no clue how to de-couple it after
checking other locks in the splat. There is an onging effort to make all
printk() as deferred, so until that happens, workaround it for now as a
short-term fix.

LTP: starting iogen01 (export LTPROOT; rwtest -N iogen01 -i 120s -s
read,write -Da -Dv -n 2 500b:$TMPDIR/doio.f1.$$
1000b:$TMPDIR/doio.f2.$$)
WARNING: possible circular locking dependency detected
------------------------------------------------------
doio/49441 is trying to acquire lock:
ffff008b7cff7290 (&(&zone->lock)->rlock){..-.}, at: rmqueue+0x138/0x2050

but task is already holding lock:
60ff000822352818 (&pool->lock/1){-.-.}, at: start_flush_work+0xd8/0x3f0

  which lock already depends on the new lock.

  the existing dependency chain (in reverse order) is:

  -> #4 (&pool->lock/1){-.-.}:
       lock_acquire+0x320/0x360
       _raw_spin_lock+0x64/0x80
       __queue_work+0x4b4/0xa10
       queue_work_on+0xac/0x11c
       tty_schedule_flip+0x84/0xbc
       tty_flip_buffer_push+0x1c/0x28
       pty_write+0x98/0xd0
       n_tty_write+0x450/0x60c
       tty_write+0x338/0x474
       __vfs_write+0x88/0x214
       vfs_write+0x12c/0x1a4
       redirected_tty_write+0x90/0xdc
       do_loop_readv_writev+0x140/0x180
       do_iter_write+0xe0/0x10c
       vfs_writev+0x134/0x1cc
       do_writev+0xbc/0x130
       __arm64_sys_writev+0x58/0x8c
       el0_svc_handler+0x170/0x240
       el0_sync_handler+0x150/0x250
       el0_sync+0x164/0x180

  -> #3 (&(&port->lock)->rlock){-.-.}:
       lock_acquire+0x320/0x360
       _raw_spin_lock_irqsave+0x7c/0x9c
       tty_port_tty_get+0x24/0x60
       tty_port_default_wakeup+0x1c/0x3c
       tty_port_tty_wakeup+0x34/0x40
       uart_write_wakeup+0x28/0x44
       pl011_tx_chars+0x1b8/0x270
       pl011_start_tx+0x24/0x70
       __uart_start+0x5c/0x68
       uart_write+0x164/0x1c8
       do_output_char+0x33c/0x348
       n_tty_write+0x4bc/0x60c
       tty_write+0x338/0x474
       redirected_tty_write+0xc0/0xdc
       do_loop_readv_writev+0x140/0x180
       do_iter_write+0xe0/0x10c
       vfs_writev+0x134/0x1cc
       do_writev+0xbc/0x130
       __arm64_sys_writev+0x58/0x8c
       el0_svc_handler+0x170/0x240
       el0_sync_handler+0x150/0x250
       el0_sync+0x164/0x180

  -> #2 (&port_lock_key){-.-.}:
       lock_acquire+0x320/0x360
       _raw_spin_lock+0x64/0x80
       pl011_console_write+0xec/0x2cc
       console_unlock+0x794/0x96c
       vprintk_emit+0x260/0x31c
       vprintk_default+0x54/0x7c
       vprintk_func+0x218/0x254
       printk+0x7c/0xa4
       register_console+0x734/0x7b0
       uart_add_one_port+0x734/0x834
       pl011_register_port+0x6c/0xac
       sbsa_uart_probe+0x234/0x2ec
       platform_drv_probe+0xd4/0x124
       really_probe+0x250/0x71c
       driver_probe_device+0xb4/0x200
       __device_attach_driver+0xd8/0x188
       bus_for_each_drv+0xbc/0x110
       __device_attach+0x120/0x220
       device_initial_probe+0x20/0x2c
       bus_probe_device+0x54/0x100
       device_add+0xae8/0xc2c
       platform_device_add+0x278/0x3b8
       platform_device_register_full+0x238/0x2ac
       acpi_create_platform_device+0x2dc/0x3a8
       acpi_bus_attach+0x390/0x3cc
       acpi_bus_attach+0x108/0x3cc
       acpi_bus_attach+0x108/0x3cc
       acpi_bus_attach+0x108/0x3cc
       acpi_bus_scan+0x7c/0xb0
       acpi_scan_init+0xe4/0x304
       acpi_init+0x100/0x114
       do_one_initcall+0x348/0x6a0
       do_initcall_level+0x190/0x1fc
       do_basic_setup+0x34/0x4c
       kernel_init_freeable+0x19c/0x260
       kernel_init+0x18/0x338
       ret_from_fork+0x10/0x18

  -> #1 (console_owner){-...}:
       lock_acquire+0x320/0x360
       console_lock_spinning_enable+0x6c/0x7c
       console_unlock+0x4f8/0x96c
       vprintk_emit+0x260/0x31c
       vprintk_default+0x54/0x7c
       vprintk_func+0x218/0x254
       printk+0x7c/0xa4
       get_random_u64+0x1c4/0x1dc
       shuffle_pick_tail+0x40/0xac
       __free_one_page+0x424/0x710
       free_one_page+0x70/0x120
       __free_pages_ok+0x61c/0xa94
       __free_pages_core+0x1bc/0x294
       memblock_free_pages+0x38/0x48
       __free_pages_memory+0xcc/0xfc
       __free_memory_core+0x70/0x78
       free_low_memory_core_early+0x148/0x18c
       memblock_free_all+0x18/0x54
       mem_init+0xb4/0x17c
       mm_init+0x14/0x38
       start_kernel+0x19c/0x530

  -> #0 (&(&zone->lock)->rlock){..-.}:
       validate_chain+0xf6c/0x2e2c
       __lock_acquire+0x868/0xc2c
       lock_acquire+0x320/0x360
       _raw_spin_lock+0x64/0x80
       rmqueue+0x138/0x2050
       get_page_from_freelist+0x474/0x688
       __alloc_pages_nodemask+0x3b4/0x18dc
       alloc_pages_current+0xd0/0xe0
       alloc_slab_page+0x2b4/0x5e0
       new_slab+0xc8/0x6bc
       ___slab_alloc+0x3b8/0x640
       kmem_cache_alloc+0x4b4/0x588
       __debug_object_init+0x778/0x8b4
       debug_object_init_on_stack+0x40/0x50
       start_flush_work+0x16c/0x3f0
       __flush_work+0xb8/0x124
       flush_work+0x20/0x30
       xlog_cil_force_lsn+0x88/0x204 [xfs]
       xfs_log_force_lsn+0x128/0x1b8 [xfs]
       xfs_file_fsync+0x3c4/0x488 [xfs]
       vfs_fsync_range+0xb0/0xd0
       generic_write_sync+0x80/0xa0 [xfs]
       xfs_file_buffered_aio_write+0x66c/0x6e4 [xfs]
       xfs_file_write_iter+0x1a0/0x218 [xfs]
       __vfs_write+0x1cc/0x214
       vfs_write+0x12c/0x1a4
       ksys_write+0xb0/0x120
       __arm64_sys_write+0x54/0x88
       el0_svc_handler+0x170/0x240
       el0_sync_handler+0x150/0x250
       el0_sync+0x164/0x180

       other info that might help us debug this:

 Chain exists of:
   &(&zone->lock)->rlock --> &(&port->lock)->rlock --> &pool->lock/1

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&pool->lock/1);
                               lock(&(&port->lock)->rlock);
                               lock(&pool->lock/1);
  lock(&(&zone->lock)->rlock);

                *** DEADLOCK ***

4 locks held by doio/49441:
 #0: a0ff00886fc27408 (sb_writers#8){.+.+}, at: vfs_write+0x118/0x1a4
 #1: 8fff00080810dfe0 (&xfs_nondir_ilock_class){++++}, at:
xfs_ilock+0x2a8/0x300 [xfs]
 #2: ffff9000129f2390 (rcu_read_lock){....}, at:
rcu_lock_acquire+0x8/0x38
 #3: 60ff000822352818 (&pool->lock/1){-.-.}, at:
start_flush_work+0xd8/0x3f0

               stack backtrace:
CPU: 48 PID: 49441 Comm: doio Tainted: G        W
Hardware name: HPE Apollo 70             /C01_APACHE_MB         , BIOS
L50_5.13_1.11 06/18/2019
Call trace:
 dump_backtrace+0x0/0x248
 show_stack+0x20/0x2c
 dump_stack+0xe8/0x150
 print_circular_bug+0x368/0x380
 check_noncircular+0x28c/0x294
 validate_chain+0xf6c/0x2e2c
 __lock_acquire+0x868/0xc2c
 lock_acquire+0x320/0x360
 _raw_spin_lock+0x64/0x80
 rmqueue+0x138/0x2050
 get_page_from_freelist+0x474/0x688
 __alloc_pages_nodemask+0x3b4/0x18dc
 alloc_pages_current+0xd0/0xe0
 alloc_slab_page+0x2b4/0x5e0
 new_slab+0xc8/0x6bc
 ___slab_alloc+0x3b8/0x640
 kmem_cache_alloc+0x4b4/0x588
 __debug_object_init+0x778/0x8b4
 debug_object_init_on_stack+0x40/0x50
 start_flush_work+0x16c/0x3f0
 __flush_work+0xb8/0x124
 flush_work+0x20/0x30
 xlog_cil_force_lsn+0x88/0x204 [xfs]
 xfs_log_force_lsn+0x128/0x1b8 [xfs]
 xfs_file_fsync+0x3c4/0x488 [xfs]
 vfs_fsync_range+0xb0/0xd0
 generic_write_sync+0x80/0xa0 [xfs]
 xfs_file_buffered_aio_write+0x66c/0x6e4 [xfs]
 xfs_file_write_iter+0x1a0/0x218 [xfs]
 __vfs_write+0x1cc/0x214
 vfs_write+0x12c/0x1a4
 ksys_write+0xb0/0x120
 __arm64_sys_write+0x54/0x88
 el0_svc_handler+0x170/0x240
 el0_sync_handler+0x150/0x250
 el0_sync+0x164/0x180

Reviewed-by: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Signed-off-by: Qian Cai <cai@lca.pw>
Link: https://lore.kernel.org/r/1573679785-21068-1-git-send-email-cai@lca.pw
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iommu/vt-d: Fix off-by-one in PASID allocation

[ Upstream commit 39d630e332144028f56abba83d94291978e72df1 ]

PASID allocator uses IDR which is exclusive for the end of the
allocation range. There is no need to decrement pasid_max.

Fixes: af39507305fb ("iommu/vt-d: Apply global PASID in SVA")
Reported-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpio: gpio-grgpio: fix possible sleep-in-atomic-context bugs in grgpio_irq_map/unmap()

[ Upstream commit e36eaf94be8f7bc4e686246eed3cf92d845e2ef8 ]

The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:

drivers/gpio/gpio-grgpio.c, 261:
request_irq in grgpio_irq_map
drivers/gpio/gpio-grgpio.c, 255:
_raw_spin_lock_irqsave in grgpio_irq_map

drivers/gpio/gpio-grgpio.c, 318:
free_irq in grgpio_irq_unmap
drivers/gpio/gpio-grgpio.c, 299:
_raw_spin_lock_irqsave in grgpio_irq_unmap

request_irq() and free_irq() can sleep at runtime.

To fix these bugs, request_irq() and free_irq() are called without
holding the spinlock.

These bugs are found by a static analysis tool STCheck written by myself.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Link: https://lore.kernel.org/r/20191218132605.10594-1-baijiaju1990@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

powerpc/powernv/iov: Ensure the pdn for VFs always contains a valid PE number

[ Upstream commit 3b5b9997b331e77ce967eba2c4bc80dc3134a7fe ]

On pseries there is a bug with adding hotplugged devices to an IOMMU
group. For a number of dumb reasons fixing that bug first requires
re-working how VFs are configured on PowerNV. For background, on
PowerNV we use the pcibios_sriov_enable() hook to do two things:

  1. Create a pci_dn structure for each of the VFs, and
  2. Configure the PHB's internal BARs so the MMIO range for each VF
     maps to a unique PE.

Roughly speaking a PE is the hardware counterpart to a Linux IOMMU
group since all the devices in a PE share the same IOMMU table. A PE
also defines the set of devices that should be isolated in response to
a PCI error (i.e. bad DMA, UR/CA, AER events, etc). When isolated all
MMIO and DMA traffic to and from devicein the PE is blocked by the
root complex until the PE is recovered by the OS.

The requirement to block MMIO causes a giant headache because the P8
PHB generally uses a fixed mapping between MMIO addresses and PEs. As
a result we need to delay configuring the IOMMU groups for device
until after MMIO resources are assigned. For physical devices (i.e.
non-VFs) the PE assignment is done in pcibios_setup_bridge() which is
called immediately after the MMIO resources for downstream
devices (and the bridge's windows) are assigned. For VFs the setup is
more complicated because:

  a) pcibios_setup_bridge() is not called again when VFs are activated, and
  b) The pci_dev for VFs are created by generic code which runs after
     pcibios_sriov_enable() is called.

The work around for this is a two step process:

  1. A fixup in pcibios_add_device() is used to initialised the cached
     pe_number in pci_dn, then
  2. A bus notifier then adds the device to the IOMMU group for the PE
     specified in pci_dn->pe_number.

A side effect fixing the pseries bug mentioned in the first paragraph
is moving the fixup out of pcibios_add_device() and into
pcibios_bus_add_device(), which is called much later. This results in
step 2. failing because pci_dn->pe_number won't be initialised when
the bus notifier is run.

We can fix this by removing the need for the fixup. The PE for a VF is
known before the VF is even scanned so we can initialise
pci_dn->pe_number pcibios_sriov_enable() instead. Unfortunately,
moving the initialisation causes two problems:

  1. We trip the WARN_ON() in the current fixup code, and
  2. The EEH core clears pdn->pe_number when recovering a VF and
     relies on the fixup to correctly re-set it.

The only justification for either of these is a comment in
eeh_rmv_device() suggesting that pdn->pe_number *must* be set to
IODA_INVALID_PE in order for the VF to be scanned. However, this
comment appears to have no basis in reality. Both bugs can be fixed by
just deleting the code.

Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191028085424.12006-1-oohall@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

media: i2c: mt9v032: fix enum mbus codes and frame sizes

[ Upstream commit 1451d5ae351d938a0ab1677498c893f17b9ee21d ]

This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).

[Sakari Ailus: rewrapped commit message]

Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pxa168fb: Fix the function used to release some memory in an error handling path

[ Upstream commit 3c911fe799d1c338d94b78e7182ad452c37af897 ]

In the probe function, some resources are allocated using 'dma_alloc_wc()',
they should be released with 'dma_free_wc()', not 'dma_free_coherent()'.

We already use 'dma_free_wc()' in the remove function, but not in the
error handling path of the probe function.

Also, remove a useless 'PAGE_ALIGN()'. 'info->fix.smem_len' is already
PAGE_ALIGNed.

Fixes: 638772c7553f ("fb: add support of LCD display controller on pxa168/910 (base layer)")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Lubomir Rintel <lkundrak@v3.sk>
CC: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190831100024.3248-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: sh-pfc: sh7264: Fix CAN function GPIOs

[ Upstream commit 55b1cb1f03ad5eea39897d0c74035e02deddcff2 ]

pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.

Fix this by:
  - Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
    configures the combined "CTX0&CTX1" output signal,
  - Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
    the shared "CRX0/CRX1" input signal, which is fed to both CAN
    inputs,
  - Adding the missing function GPIO definition for "CTX0&CTX1" to
    pinmux_func_gpios[],
  - Moving all CAN enums next to each other.

See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
  [1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
      Version),
  [2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
      Version,
  [3] Table 1.4 List of Pins,
  [4] Figure 20.29 Connection Example when Using This Module as 1-Channel
      Module (64 Mailboxes x 1 Channel),
  [5] Table 32.10 Multiplexed Pins (Port J),
  [6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).

Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug.  But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>

gianfar: Fix TX timestamping with a stacked DSA driver

[ Upstream commit c26a2c2ddc0115eb088873f5c309cf46b982f522 ]

The driver wrongly assumes that it is the only entity that can set the
SKBTX_IN_PROGRESS bit of the current skb. Therefore, in the
gfar_clean_tx_ring function, where the TX timestamp is collected if
necessary, the aforementioned bit is used to discriminate whether or not
the TX timestamp should be delivered to the socket's error queue.

But a stacked driver such as a DSA switch can also set the
SKBTX_IN_PROGRESS bit, which is actually exactly what it should do in
order to denote that the hardware timestamping process is undergoing.

Therefore, gianfar would misinterpret the "in progress" bit as being its
own, and deliver a second skb clone in the socket's error queue,
completely throwing off a PTP process which is not expecting to receive
it, _even though_ TX timestamping is not enabled for gianfar.

There have been discussions [0] as to whether non-MAC drivers need or
not to set SKBTX_IN_PROGRESS at all (whose purpose is to avoid sending 2
timestamps, a sw and a hw one, to applications which only expect one).
But as of this patch, there are at least 2 PTP drivers that would break
in conjunction with gianfar: the sja1105 DSA switch and the felix
switch, by way of its ocelot core driver.

So regardless of that conclusion, fix the gianfar driver to not do stuff
based on flags set by others and not intended for it.

[0]: https://www.spinics.net/lists/netdev/msg619699.html

Fixes: f0ee7acfcdd4 ("gianfar: Add hardware TX timestamping support")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ALSA: ctl: allow TLV read operation for callback type of element in locked case

[ Upstream commit d61fe22c2ae42d9fd76c34ef4224064cca4b04b0 ]

A design of ALSA control core allows applications to execute three
operations for TLV feature; read, write and command. Furthermore, it
allows driver developers to process the operations by two ways; allocated
array or callback function. In the former, read operation is just allowed,
thus developers uses the latter when device driver supports variety of
models or the target model is expected to dynamically change information
stored in TLV container.

The core also allows applications to lock any element so that the other
applications can't perform write operation to the element for element
value and TLV information. When the element is locked, write and command
operation for TLV information are prohibited as well as element value.
Any read operation should be allowed in the case.

At present, when an element has callback function for TLV information,
TLV read operation returns EPERM if the element is locked. On the
other hand, the read operation is success when an element has allocated
array for TLV information. In both cases, read operation is success for
element value expectedly.

This commit fixes the bug. This change can be backported to v4.14
kernel or later.

Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20191223093347.15279-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ext4: fix ext4_dax_read/write inode locking sequence for IOCB_NOWAIT

[ Upstream commit f629afe3369e9885fd6e9cc7a4f514b6a65cf9e9 ]

Apparently our current rwsem code doesn't like doing the trylock, then
lock for real scheme.  So change our dax read/write methods to just do the
trylock for the RWF_NOWAIT case.
This seems to fix AIM7 regression in some scalable filesystems upto ~25%
in some cases. Claimed in commit 942491c9e6d6 ("xfs: fix AIM7 regression")

Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Matthew Bobrowski <mbobrowski@mbobrowski.org>
Tested-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: Ritesh Harjani <riteshh@linux.ibm.com>
Link: https://lore.kernel.org/r/20191212055557.11151-2-riteshh@linux.ibm.com
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

leds: pca963x: Fix open-drain initialization

[ Upstream commit 697529091ac7a0a90ca349b914bb30641c13c753 ]

Before commit bb29b9cccd95 ("leds: pca963x: Add bindings to invert
polarity") Mode register 2 was initialized directly with either 0x01
or 0x05 for open-drain or totem pole (push-pull) configuration.

Afterwards, MODE2 initialization started using bitwise operations on
top of the default MODE2 register value (0x05). Using bitwise OR for
setting OUTDRV with 0x01 and 0x05 does not produce correct results.
When open-drain is used, instead of setting OUTDRV to 0, the driver
keeps it as 1:

Open-drain: 0x05 | 0x01 -> 0x05 (0b101 - incorrect)
Totem pole: 0x05 | 0x05 -> 0x05 (0b101 - correct but still wrong)

Now OUTDRV setting uses correct bitwise operations for initialization:

Open-drain: 0x05 & ~0x04 -> 0x01 (0b001 - correct)
Totem pole: 0x05 | 0x04 -> 0x05 (0b101 - correct)

Additional MODE2 register definitions are introduced now as well.

Fixes: bb29b9cccd95 ("leds: pca963x: Add bindings to invert polarity")
Signed-off-by: Zahari Petkov <zahari@balena.io>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

brcmfmac: Fix use after free in brcmf_sdio_readframes()

[ Upstream commit 216b44000ada87a63891a8214c347e05a4aea8fe ]

The brcmu_pkt_buf_free_skb() function frees "pkt" so it leads to a
static checker warning:

    drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1974 brcmf_sdio_readframes()
    error: dereferencing freed memory 'pkt'

It looks like there was supposed to be a continue after we free "pkt".

Fixes: 4754fceeb9a6 ("brcmfmac: streamline SDIO read frame routine")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

cpu/hotplug, stop_machine: Fix stop_machine vs hotplug order

[ Upstream commit 45178ac0cea853fe0e405bf11e101bdebea57b15 ]

Paul reported a very sporadic, rcutorture induced, workqueue failure.
When the planets align, the workqueue rescuer's self-migrate fails and
then triggers a WARN for running a work on the wrong CPU.

Tejun then figured that set_cpus_allowed_ptr()'s stop_one_cpu() call
could be ignored! When stopper->enabled is false, stop_machine will
insta complete the work, without actually doing the work. Worse, it
will not WARN about this (we really should fix this).

It turns out there is a small window where a freshly online'ed CPU is
marked 'online' but doesn't yet have the stopper task running:

BP AP

bringup_cpu()
  __cpu_up(cpu, idle)  --> start_secondary()
...
cpu_startup_entry()
  bringup_wait_for_ap()
    wait_for_ap_thread() <--   cpuhp_online_idle()
  while (1)
    do_idle()

... available to run kthreads ...

    stop_machine_unpark()
      stopper->enable = true;

Close this by moving the stop_machine_unpark() into
cpuhp_online_idle(), such that the stopper thread is ready before we
start the idle loop and schedule.

Reported-by: "Paul E. McKenney" <paulmck@kernel.org>
Debugged-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: "Paul E. McKenney" <paulmck@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/gma500: Fixup fbdev stolen size usage evaluation

[ Upstream commit fd1a5e521c3c083bb43ea731aae0f8b95f12b9bd ]

psbfb_probe performs an evaluation of the required size from the stolen
GTT memory, but gets it wrong in two distinct ways:
- The resulting size must be page-size-aligned;
- The size to allocate is derived from the surface dimensions, not the fb
  dimensions.

When two connectors are connected with different modes, the smallest will
be stored in the fb dimensions, but the size that needs to be allocated must
match the largest (surface) dimensions. This is what is used in the actual
allocation code.

Fix this by correcting the evaluation to conform to the two points above.
It allows correctly switching to 16bpp when one connector is e.g. 1920x1080
and the other is 1024x768.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191107153048.843881-1-paul.kocialkowski@bootlin.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

KVM: nVMX: Use correct root level for nested EPT shadow page tables

[ Upstream commit 148d735eb55d32848c3379e460ce365f2c1cbe4b ]

Hardcode the EPT page-walk level for L2 to be 4 levels, as KVM's MMU
currently also hardcodes the page walk level for nested EPT to be 4
levels.  The L2 guest is all but guaranteed to soft hang on its first
instruction when L1 is using EPT, as KVM will construct 4-level page
tables and then tell hardware to use 5-level page tables.

Fixes: 855feb673640 ("KVM: MMU: Add 5 level EPT & Shadow page table support.")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "KVM: VMX: Add non-canonical check on writes to RTIT address MSRs"

This reverts commit 57211b7366cc2abf784c35e537b256e7fcddc91e.

This patch isn't needed on 4.19 and older.

Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "KVM: nVMX: Use correct root level for nested EPT shadow page tables"

This reverts commit 740d876bd9565857a695ce7c05efda4eba5bc585.

Signed-off-by: Sasha Levin <sashal@kernel.org>

net/sched: flower: add missing validation of TCA_FLOWER_FLAGS

[ Upstream commit e2debf0852c4d66ba1a8bde12869b196094c70a7 ]

unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_flower' doesn't validate the size of
netlink attribute 'TCA_FLOWER_FLAGS' provided by user: add a proper entry
to fl_policy.

Fixes: 5b33f48842fa ("net/flower: Introduce hardware offload support")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS

[ Upstream commit 1afa3cc90f8fb745c777884d79eaa1001d6927a6 ]

unlike other classifiers that can be offloaded (i.e. users can set flags
like 'skip_hw' and 'skip_sw'), 'cls_matchall' doesn't validate the size
of netlink attribute 'TCA_MATCHALL_FLAGS' provided by user: add a proper
entry to mall_policy.

Fixes: b87f7936a932 ("net/sched: Add match-all classifier hw offloading.")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: dsa: tag_qca: Make sure there is headroom for tag

[ Upstream commit 04fb91243a853dbde216d829c79d9632e52aa8d9 ]

Passing tag size to skb_cow_head will make sure
there is enough headroom for the tag data.
This change does not introduce any overhead in case there
is already available headroom for tag.

Signed-off-by: Per Forlin <perfn@axis.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/smc: fix leak of kernel memory to user space

[ Upstream commit 457fed775c97ac2c0cd1672aaf2ff2c8a6235e87 ]

As nlmsg_put() does not clear the memory that is reserved,
it this the caller responsability to make sure all of this
memory will be written, in order to not reveal prior content.

While we are at it, we can provide the socket cookie even
if clsock is not set.

syzbot reported :

BUG: KMSAN: uninit-value in __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline]
BUG: KMSAN: uninit-value in __fswab32 include/uapi/linux/swab.h:59 [inline]
BUG: KMSAN: uninit-value in __swab32p include/uapi/linux/swab.h:179 [inline]
BUG: KMSAN: uninit-value in __be32_to_cpup include/uapi/linux/byteorder/little_endian.h:82 [inline]
BUG: KMSAN: uninit-value in get_unaligned_be32 include/linux/unaligned/access_ok.h:30 [inline]
BUG: KMSAN: uninit-value in ____bpf_skb_load_helper_32 net/core/filter.c:240 [inline]
BUG: KMSAN: uninit-value in ____bpf_skb_load_helper_32_no_cache net/core/filter.c:255 [inline]
BUG: KMSAN: uninit-value in bpf_skb_load_helper_32_no_cache+0x14a/0x390 net/core/filter.c:252
CPU: 1 PID: 5262 Comm: syz-executor.5 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x1c9/0x220 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:118
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 __arch_swab32 arch/x86/include/uapi/asm/swab.h:10 [inline]
 __fswab32 include/uapi/linux/swab.h:59 [inline]
 __swab32p include/uapi/linux/swab.h:179 [inline]
 __be32_to_cpup include/uapi/linux/byteorder/little_endian.h:82 [inline]
 get_unaligned_be32 include/linux/unaligned/access_ok.h:30 [inline]
 ____bpf_skb_load_helper_32 net/core/filter.c:240 [inline]
 ____bpf_skb_load_helper_32_no_cache net/core/filter.c:255 [inline]
 bpf_skb_load_helper_32_no_cache+0x14a/0x390 net/core/filter.c:252

Uninit was created at:
 kmsan_save_stack_with_flags mm/kmsan/kmsan.c:144 [inline]
 kmsan_internal_poison_shadow+0x66/0xd0 mm/kmsan/kmsan.c:127
 kmsan_kmalloc_large+0x73/0xc0 mm/kmsan/kmsan_hooks.c:128
 kmalloc_large_node_hook mm/slub.c:1406 [inline]
 kmalloc_large_node+0x282/0x2c0 mm/slub.c:3841
 __kmalloc_node_track_caller+0x44b/0x1200 mm/slub.c:4368
 __kmalloc_reserve net/core/skbuff.c:141 [inline]
 __alloc_skb+0x2fd/0xac0 net/core/skbuff.c:209
 alloc_skb include/linux/skbuff.h:1049 [inline]
 netlink_dump+0x44b/0x1ab0 net/netlink/af_netlink.c:2224
 __netlink_dump_start+0xbb2/0xcf0 net/netlink/af_netlink.c:2352
 netlink_dump_start include/linux/netlink.h:233 [inline]
 smc_diag_handler_dump+0x2ba/0x300 net/smc/smc_diag.c:242
 sock_diag_rcv_msg+0x211/0x610 net/core/sock_diag.c:256
 netlink_rcv_skb+0x451/0x650 net/netlink/af_netlink.c:2477
 sock_diag_rcv+0x63/0x80 net/core/sock_diag.c:275
 netlink_unicast_kernel net/netlink/af_netlink.c:1302 [inline]
 netlink_unicast+0xf9e/0x1100 net/netlink/af_netlink.c:1328
 netlink_sendmsg+0x1248/0x14d0 net/netlink/af_netlink.c:1917
 sock_sendmsg_nosec net/socket.c:639 [inline]
 sock_sendmsg net/socket.c:659 [inline]
 kernel_sendmsg+0x433/0x440 net/socket.c:679
 sock_no_sendpage+0x235/0x300 net/core/sock.c:2740
 kernel_sendpage net/socket.c:3776 [inline]
 sock_sendpage+0x1e1/0x2c0 net/socket.c:937
 pipe_to_sendpage+0x38c/0x4c0 fs/splice.c:458
 splice_from_pipe_feed fs/splice.c:512 [inline]
 __splice_from_pipe+0x539/0xed0 fs/splice.c:636
 splice_from_pipe fs/splice.c:671 [inline]
 generic_splice_sendpage+0x1d5/0x2d0 fs/splice.c:844
 do_splice_from fs/splice.c:863 [inline]
 do_splice fs/splice.c:1170 [inline]
 __do_sys_splice fs/splice.c:1447 [inline]
 __se_sys_splice+0x2380/0x3350 fs/splice.c:1427
 __x64_sys_splice+0x6e/0x90 fs/splice.c:1427
 do_syscall_64+0xb8/0x160 arch/x86/entry/common.c:296
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: f16a7dd5cf27 ("smc: netlink interface for SMC sockets")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ursula Braun <ubraun@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

enic: prevent waking up stopped tx queues over watchdog reset

[ Upstream commit 0f90522591fd09dd201065c53ebefdfe3c6b55cb ]

Recent months, our customer reported several kernel crashes all
preceding with following message:
NETDEV WATCHDOG: eth2 (enic): transmit queue 0 timed out
Error message of one of those crashes:
BUG: unable to handle kernel paging request at ffffffffa007e090

After analyzing severl vmcores, I found that most of crashes are
caused by memory corruption. And all the corrupted memory areas
are overwritten by data of network packets. Moreover, I also found
that the tx queues were enabled over watchdog reset.

After going through the source code, I found that in enic_stop(),
the tx queues stopped by netif_tx_disable() could be woken up over
a small time window between netif_tx_disable() and the
napi_disable() by the following code path:
napi_poll->
  enic_poll_msix_wq->
     vnic_cq_service->
        enic_wq_service->
           netif_wake_subqueue(enic->netdev, q_number)->
              test_and_clear_bit(__QUEUE_STATE_DRV_XOFF, &txq->state)
In turn, upper netowrk stack could queue skb to ENIC NIC though
enic_hard_start_xmit(). And this might introduce some race condition.

Our customer comfirmed that this kind of kernel crash doesn't occur over
90 days since they applied this patch.

Signed-off-by: Firo Yang <firo.yang@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

core: Don't skip generic XDP program execution for cloned SKBs

[ Upstream commit ad1e03b2b3d4430baaa109b77bc308dc73050de3 ]

The current generic XDP handler skips execution of XDP programs entirely if
an SKB is marked as cloned. This leads to some surprising behaviour, as
packets can end up being cloned in various ways, which will make an XDP
program not see all the traffic on an interface.

This was discovered by a simple test case where an XDP program that always
returns XDP_DROP is installed on a veth device. When combining this with
the Scapy packet sniffer (which uses an AF_PACKET) socket on the sending
side, SKBs reliably end up in the cloned state, causing them to be passed
through to the receiving interface instead of being dropped. A minimal
reproducer script for this is included below.

This patch fixed the issue by simply triggering the existing linearisation
code for cloned SKBs instead of skipping the XDP program execution. This
behaviour is in line with the behaviour of the native XDP implementation
for the veth driver, which will reallocate and copy the SKB data if the SKB
is marked as shared.

Reproducer Python script (requires BCC and Scapy):

from scapy.all import TCP, IP, Ether, sendp, sniff, AsyncSniffer, Raw, UDP
from bcc import BPF
import time, sys, subprocess, shlex

SKB_MODE = (1 << 1)
DRV_MODE = (1 << 2)
PYTHON=sys.executable

def client():
    time.sleep(2)
    # Sniffing on the sender causes skb_cloned() to be set
    s = AsyncSniffer()
    s.start()

    for p in range(10):
        sendp(Ether(dst="aa:aa:aa:aa:aa:aa", src="cc:cc:cc:cc:cc:cc")/IP()/UDP()/Raw("Test"),
              verbose=False)
        time.sleep(0.1)

    s.stop()
    return 0

def server(mode):
    prog = BPF(text="int dummy_drop(struct xdp_md *ctx) {return XDP_DROP;}")
    func = prog.load_func("dummy_drop", BPF.XDP)
    prog.attach_xdp("a_to_b", func, mode)

    time.sleep(1)

    s = sniff(iface="a_to_b", count=10, timeout=15)
    if len(s):
        print(f"Got {len(s)} packets - should have gotten 0")
        return 1
    else:
        print("Got no packets - as expected")
        return 0

if len(sys.argv) < 2:
    print(f"Usage: {sys.argv[0]} <skb|drv>")
    sys.exit(1)

if sys.argv[1] == "client":
    sys.exit(client())
elif sys.argv[1] == "server":
    mode = SKB_MODE if sys.argv[2] == 'skb' else DRV_MODE
    sys.exit(server(mode))
else:
    try:
        mode = sys.argv[1]
        if mode not in ('skb', 'drv'):
            print(f"Usage: {sys.argv[0]} <skb|drv>")
            sys.exit(1)
        print(f"Running in {mode} mode")

        for cmd in [
                'ip netns add netns_a',
                'ip netns add netns_b',
                'ip -n netns_a link add a_to_b type veth peer name b_to_a netns netns_b',
                # Disable ipv6 to make sure there's no address autoconf traffic
                'ip netns exec netns_a sysctl -qw net.ipv6.conf.a_to_b.disable_ipv6=1',
                'ip netns exec netns_b sysctl -qw net.ipv6.conf.b_to_a.disable_ipv6=1',
                'ip -n netns_a link set dev a_to_b address aa:aa:aa:aa:aa:aa',
                'ip -n netns_b link set dev b_to_a address cc:cc:cc:cc:cc:cc',
                'ip -n netns_a link set dev a_to_b up',
                'ip -n netns_b link set dev b_to_a up']:
            subprocess.check_call(shlex.split(cmd))

        server = subprocess.Popen(shlex.split(f"ip netns exec netns_a {PYTHON} {sys.argv[0]} server {mode}"))
        client = subprocess.Popen(shlex.split(f"ip netns exec netns_b {PYTHON} {sys.argv[0]} client"))

        client.wait()
        server.wait()
        sys.exit(server.returncode)

    finally:
        subprocess.run(shlex.split("ip netns delete netns_a"))
        subprocess.run(shlex.split("ip netns delete netns_b"))

Fixes: d445516966dc ("net: xdp: support xdp generic on virtual devices")
Reported-by: Stepan Horacek <shoracek@redhat.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.19.105

KVM: x86/mmu: Fix struct guest_walker arrays for 5-level paging

[ Upstream commit f6ab0107a4942dbf9a5cf0cca3f37e184870a360 ]

Define PT_MAX_FULL_LEVELS as PT64_ROOT_MAX_LEVEL, i.e. 5, to fix shadow
paging for 5-level guest page tables.  PT_MAX_FULL_LEVELS is used to
size the arrays that track guest pages table information, i.e. using a
"max levels" of 4 causes KVM to access garbage beyond the end of an
array when querying state for level 5 entries.  E.g. FNAME(gpte_changed)
will read garbage and most likely return %true for a level 5 entry,
soft-hanging the guest because FNAME(fetch) will restart the guest
instead of creating SPTEs because it thinks the guest PTE has changed.

Note, KVM doesn't yet support 5-level nested EPT, so PT_MAX_FULL_LEVELS
gets to stay "4" for the PTTYPE_EPT case.

Fixes: 855feb673640 ("KVM: MMU: Add 5 level EPT & Shadow page table support.")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

jbd2: do not clear the BH_Mapped flag when forgetting a metadata buffer

[ Upstream commit c96dceeabf765d0b1b1f29c3bf50a5c01315b820 ]

Commit 904cdbd41d74 ("jbd2: clear dirty flag when revoking a buffer from
an older transaction") set the BH_Freed flag when forgetting a metadata
buffer which belongs to the committing transaction, it indicate the
committing process clear dirty bits when it is done with the buffer. But
it also clear the BH_Mapped flag at the same time, which may trigger
below NULL pointer oops when block_size < PAGE_SIZE.

rmdir 1             kjournald2                 mkdir 2
                    jbd2_journal_commit_transaction
    commit transaction N
jbd2_journal_forget
set_buffer_freed(bh1)
                    jbd2_journal_commit_transaction
                     commit transaction N+1
                     ...
                     clear_buffer_mapped(bh1)
                                               ext4_getblk(bh2 ummapped)
                                               ...
                                               grow_dev_page
                                                init_page_buffers
                                                 bh1->b_private=NULL
                                                 bh2->b_private=NULL
                     jbd2_journal_put_journal_head(jh1)
                      __journal_remove_journal_head(hb1)
       jh1 is NULL and trigger oops

*) Dir entry block bh1 and bh2 belongs to one page, and the bh2 has
   already been unmapped.

For the metadata buffer we forgetting, we should always keep the mapped
flag and clear the dirty flags is enough, so this patch pick out the
these buffers and keep their BH_Mapped flag.

Link: https://lore.kernel.org/r/20200213063821.30455-3-yi.zhang@huawei.com
Fixes: 904cdbd41d74 ("jbd2: clear dirty flag when revoking a buffer from an older transaction")
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

jbd2: move the clearing of b_modified flag to the journal_unmap_buffer()

[ Upstream commit 6a66a7ded12baa6ebbb2e3e82f8cb91382814839 ]

There is no need to delay the clearing of b_modified flag to the
transaction committing time when unmapping the journalled buffer, so
just move it to the journal_unmap_buffer().

Link: https://lore.kernel.org/r/20200213063821.30455-2-yi.zhang@huawei.com
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: zhangyi (F) <yi.zhang@huawei.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

NFSv4.1 make cachethis=no for writes

commit cd1b659d8ce7697ee9799b64f887528315b9097b upstream.

Turning caching off for writes on the server should improve performance.

Fixes: fba83f34119a ("NFS: Pass "privileged" value to nfs4_init_sequence()")
Signed-off-by: Olga Kornievskaia <kolga@netapp.com>
Reviewed-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

hwmon: (pmbus/ltc2978) Fix PMBus polling of MFR_COMMON definitions.

commit cf2b012c90e74e85d8aea7d67e48868069cfee0c upstream.

Change 21537dc driver PMBus polling of MFR_COMMON from bits 5/4 to
bits 6/5. This fixs a LTC297X family bug where polling always returns
not busy even when the part is busy. This fixes a LTC388X and
LTM467X bug where polling used PEND and NOT_IN_TRANS, and BUSY was
not polled, which can lead to NACKing of commands. LTC388X and
LTM467X modules now poll BUSY and PEND, increasing reliability by
eliminating NACKing of commands.

Signed-off-by: Mike Jones <michael-a1.jones@analog.com>
Link: https://lore.kernel.org/r/1580234400-2829-2-git-send-email-michael-a1.jones@analog.com
Fixes: e04d1ce9bbb49 ("hwmon: (ltc2978) Add polling for chips requiring it")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel: Fix inaccurate period in context switch for auto-reload

commit f861854e1b435b27197417f6f90d87188003cb24 upstream.

Perf doesn't take the left period into account when auto-reload is
enabled with fixed period sampling mode in context switch.

Here is the MSR trace of the perf command as below.
(The MSR trace is simplified from a ftrace log.)

    #perf record -e cycles:p -c 2000000 -- ./triad_loop

      //The MSR trace of task schedule out
      //perf disable all counters, disable PEBS, disable GP counter 0,
      //read GP counter 0, and re-enable all counters.
      //The counter 0 stops at 0xfffffff82840
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
      write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 0
      write_msr: MSR_P6_EVNTSEL0(186), value 40003003c
      rdpmc: 0, value fffffff82840
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff

      //The MSR trace of the same task schedule in again
      //perf disable all counters, enable and set GP counter 0,
      //enable PEBS, and re-enable all counters.
      //0xffffffe17b80 (-2000000) is written to GP counter 0.
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
      write_msr: MSR_IA32_PMC0(4c1), value ffffffe17b80
      write_msr: MSR_P6_EVNTSEL0(186), value 40043003c
      write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 1
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff

When the same task schedule in again, the counter should starts from
previous left. However, it starts from the fixed period -2000000 again.

A special variant of intel_pmu_save_and_restart() is used for
auto-reload, which doesn't update the hwc->period_left.
When the monitored task schedules in again, perf doesn't know the left
period. The fixed period is used, which is inaccurate.

With auto-reload, the counter always has a negative counter value. So
the left period is -value. Update the period_left in
intel_pmu_save_and_restart_reload().

With the patch:

      //The MSR trace of task schedule out
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
      write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 0
      write_msr: MSR_P6_EVNTSEL0(186), value 40003003c
      rdpmc: 0, value ffffffe25cbc
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff

      //The MSR trace of the same task schedule in again
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value 0
      write_msr: MSR_IA32_PMC0(4c1), value ffffffe25cbc
      write_msr: MSR_P6_EVNTSEL0(186), value 40043003c
      write_msr: MSR_IA32_PEBS_ENABLE(3f1), value 1
      write_msr: MSR_CORE_PERF_GLOBAL_CTRL(38f), value f000000ff

Fixes: d31fc13fdcb2 ("perf/x86/intel: Fix event update for auto-reload")
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lkml.kernel.org/r/20200121190125.3389-1-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/time: Fix clk type in get_tod_clock

commit 0f8a206df7c920150d2aa45574fba0ab7ff6be4f upstream.

Clang warns:

In file included from ../arch/s390/boot/startup.c:3:
In file included from ../include/linux/elf.h:5:
In file included from ../arch/s390/include/asm/elf.h:132:
In file included from ../include/linux/compat.h:10:
In file included from ../include/linux/time.h:74:
In file included from ../include/linux/time32.h:13:
In file included from ../include/linux/timex.h:65:
../arch/s390/include/asm/timex.h:160:20: warning: passing 'unsigned char
[16]' to parameter of type 'char *' converts between pointers to integer
types with different sign [-Wpointer-sign]
        get_tod_clock_ext(clk);
                          ^~~
../arch/s390/include/asm/timex.h:149:44: note: passing argument to
parameter 'clk' here
static inline void get_tod_clock_ext(char *clk)
                                           ^

Change clk's type to just be char so that it matches what happens in
get_tod_clock_ext.

Fixes: 57b28f66316d ("[S390] s390_hypfs: Add new attributes")
Link: https://github.com/ClangBuiltLinux/linux/issues/861
Link: http://lkml.kernel.org/r/20200208140858.47970-1-natechancellor@gmail.com
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/core: Fix protection fault in get_pkey_idx_qp_list

commit 1dd017882e01d2fcd9c5dbbf1eb376211111c393 upstream.

We don't need to set pkey as valid in case that user set only one of pkey
index or port number, otherwise it will be resulted in NULL pointer
dereference while accessing to uninitialized pkey list.  The following
crash from Syzkaller revealed it.

  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] SMP KASAN PTI
  CPU: 1 PID: 14753 Comm: syz-executor.2 Not tainted 5.5.0-rc5 #2
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
  rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
  RIP: 0010:get_pkey_idx_qp_list+0x161/0x2d0
  Code: 01 00 00 49 8b 5e 20 4c 39 e3 0f 84 b9 00 00 00 e8 e4 42 6e fe 48
  8d 7b 10 48 b8 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 <0f> b6 04
  02 84 c0 74 08 3c 01 0f 8e d0 00 00 00 48 8d 7d 04 48 b8
  RSP: 0018:ffffc9000bc6f950 EFLAGS: 00010202
  RAX: dffffc0000000000 RBX: 0000000000000000 RCX: ffffffff82c8bdec
  RDX: 0000000000000002 RSI: ffffc900030a8000 RDI: 0000000000000010
  RBP: ffff888112c8ce80 R08: 0000000000000004 R09: fffff5200178df1f
  R10: 0000000000000001 R11: fffff5200178df1f R12: ffff888115dc4430
  R13: ffff888115da8498 R14: ffff888115dc4410 R15: ffff888115da8000
  FS:  00007f20777de700(0000) GS:ffff88811b100000(0000)
  knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000001b2f721000 CR3: 00000001173ca002 CR4: 0000000000360ee0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   port_pkey_list_insert+0xd7/0x7c0
   ib_security_modify_qp+0x6fa/0xfc0
   _ib_modify_qp+0x8c4/0xbf0
   modify_qp+0x10da/0x16d0
   ib_uverbs_modify_qp+0x9a/0x100
   ib_uverbs_write+0xaa5/0xdf0
   __vfs_write+0x7c/0x100
   vfs_write+0x168/0x4a0
   ksys_write+0xc8/0x200
   do_syscall_64+0x9c/0x390
   entry_SYSCALL_64_after_hwframe+0x44/0xa9

Fixes: d291f1a65232 ("IB/core: Enforce PKey security on QPs")
Link: https://lore.kernel.org/r/20200212080651.GB679970@unreal
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Message-Id: <20200212080651.GB679970@unreal>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/rxe: Fix soft lockup problem due to using tasklets in softirq

commit 8ac0e6641c7ca14833a2a8c6f13d8e0a435e535c upstream.

When run stress tests with RXE, the following Call Traces often occur

  watchdog: BUG: soft lockup - CPU#2 stuck for 22s! [swapper/2:0]
  ...
  Call Trace:
  <IRQ>
  create_object+0x3f/0x3b0
  kmem_cache_alloc_node_trace+0x129/0x2d0
  __kmalloc_reserve.isra.52+0x2e/0x80
  __alloc_skb+0x83/0x270
  rxe_init_packet+0x99/0x150 [rdma_rxe]
  rxe_requester+0x34e/0x11a0 [rdma_rxe]
  rxe_do_task+0x85/0xf0 [rdma_rxe]
  tasklet_action_common.isra.21+0xeb/0x100
  __do_softirq+0xd0/0x298
  irq_exit+0xc5/0xd0
  smp_apic_timer_interrupt+0x68/0x120
  apic_timer_interrupt+0xf/0x20
  </IRQ>
  ...

The root cause is that tasklet is actually a softirq. In a tasklet
handler, another softirq handler is triggered. Usually these softirq
handlers run on the same cpu core. So this will cause "soft lockup Bug".

Fixes: 8700e3e7c485 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200212072635.682689-8-leon@kernel.org
Signed-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/hfi1: Fix memory leak in _dev_comp_vect_mappings_create

commit 8a4f300b978edbbaa73ef9eca660e45eb9f13873 upstream.

Make sure to free the allocated cpumask_var_t's to avoid the following
reported memory leak by kmemleak:

$ cat /sys/kernel/debug/kmemleak
unreferenced object 0xffff8897f812d6a8 (size 8):
  comm "kworker/1:1", pid 347, jiffies 4294751400 (age 101.703s)
  hex dump (first 8 bytes):
    00 00 00 00 00 00 00 00                          ........
  backtrace:
    [<00000000bff49664>] alloc_cpumask_var_node+0x4c/0xb0
    [<0000000075d3ca81>] hfi1_comp_vectors_set_up+0x20f/0x800 [hfi1]
    [<0000000098d420df>] hfi1_init_dd+0x3311/0x4960 [hfi1]
    [<0000000071be7e52>] init_one+0x25e/0xf10 [hfi1]
    [<000000005483d4c2>] local_pci_probe+0xd4/0x180
    [<000000007c3cbc6e>] work_for_cpu_fn+0x51/0xa0
    [<000000001d626905>] process_one_work+0x8f0/0x17b0
    [<000000007e569e7e>] worker_thread+0x536/0xb50
    [<00000000fd39a4a5>] kthread+0x30c/0x3d0
    [<0000000056f2edb3>] ret_from_fork+0x3a/0x50

Fixes: 5d18ee67d4c1 ("IB/{hfi1, rdmavt, qib}: Implement CQ completion vector support")
Link: https://lore.kernel.org/r/20200205110530.12129-1-kamalheib1@gmail.com
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/core: Fix invalid memory access in spec_filter_size

commit a72f4ac1d778f7bde93dfee69bfc23377ec3d74f upstream.

Add a check that the size specified in the flow spec header doesn't cause
an overflow when calculating the filter size, and thus prevent access to
invalid memory.  The following crash from syzkaller revealed it.

  kasan: CONFIG_KASAN_INLINE enabled
  kasan: GPF could be caused by NULL-ptr deref or user memory access
  general protection fault: 0000 [#1] SMP KASAN PTI
  CPU: 1 PID: 17834 Comm: syz-executor.3 Not tainted 5.5.0-rc5 #2
  Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
  rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
  RIP: 0010:memchr_inv+0xd3/0x330
  Code: 89 f9 89 f5 83 e1 07 0f 85 f9 00 00 00 49 89 d5 49 c1 ed 03 45 85
  ed 74 6f 48 89 d9 48 b8 00 00 00 00 00 fc ff df 48 c1 e9 03 <80> 3c 01
  00 0f 85 0d 02 00 00 44 0f b6 e5 48 b8 01 01 01 01 01 01
  RSP: 0018:ffffc9000a13fa50 EFLAGS: 00010202
  RAX: dffffc0000000000 RBX: 7fff88810de9d820 RCX: 0ffff11021bd3b04
  RDX: 000000000000fff8 RSI: 0000000000000000 RDI: 7fff88810de9d820
  RBP: 0000000000000000 R08: ffff888110d69018 R09: 0000000000000009
  R10: 0000000000000001 R11: ffffed10236267cc R12: 0000000000000004
  R13: 0000000000001fff R14: ffff88810de9d820 R15: 0000000000000040
  FS:  00007f9ee0e51700(0000) GS:ffff88811b100000(0000)
  knlGS:0000000000000000
  CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000000 CR3: 0000000115ea0006 CR4: 0000000000360ee0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
  Call Trace:
   spec_filter_size.part.16+0x34/0x50
   ib_uverbs_kern_spec_to_ib_spec_filter+0x691/0x770
   ib_uverbs_ex_create_flow+0x9ea/0x1b40
   ib_uverbs_write+0xaa5/0xdf0
   __vfs_write+0x7c/0x100
   vfs_write+0x168/0x4a0
   ksys_write+0xc8/0x200
   do_syscall_64+0x9c/0x390
   entry_SYSCALL_64_after_hwframe+0x44/0xa9
  RIP: 0033:0x465b49
  Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89
  f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
  f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48
  RSP: 002b:00007f9ee0e50c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
  RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000465b49
  RDX: 00000000000003a0 RSI: 00000000200007c0 RDI: 0000000000000004
  RBP: 0000000000000003 R08: 0000000000000000 R09: 0000000000000000
  R10: 0000000000000000 R11: 0000000000000246 R12: 00007f9ee0e516bc
  R13: 00000000004ca2da R14: 000000000070deb8 R15: 00000000ffffffff
  Modules linked in:
  Dumping ftrace buffer:
     (ftrace buffer empty)

Fixes: 94e03f11ad1f ("IB/uverbs: Add support for flow tag")
Link: https://lore.kernel.org/r/20200126171500.4623-1-leon@kernel.org
Signed-off-by: Avihai Horon <avihaih@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/rdmavt: Reset all QPs when the device is shut down

commit f92e48718889b3d49cee41853402aa88cac84a6b upstream.

When the hfi1 device is shut down during a system reboot, it is possible
that some QPs might have not not freed by ULPs. More requests could be
post sent and a lingering timer could be triggered to schedule more packet
sends, leading to a crash:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
  IP: [ffffffff810a65f2] __queue_work+0x32/0x3c0
  PGD 0
  Oops: 0000 1 SMP
  Modules linked in: nvmet_rdma(OE) nvmet(OE) nvme(OE) dm_round_robin nvme_rdma(OE) nvme_fabrics(OE) nvme_core(OE) pal_raw(POE) pal_pmt(POE) pal_cache(POE) pal_pile(POE) pal(POE) pal_compatible(OE) rpcrdma sunrpc ib_isert iscsi_target_mod target_core_mod ib_iser libiscsi scsi_transport_iscsi ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm mlx4_ib sb_edac edac_core intel_powerclamp coretemp intel_rapl iosf_mbi kvm irqbypass crc32_pclmul ghash_clmulni_intel aesni_intel lrw gf128mul glue_helper ablk_helper cryptd iTCO_wdt iTCO_vendor_support mxm_wmi ipmi_ssif pcspkr ses enclosure joydev scsi_transport_sas i2c_i801 sg mei_me lpc_ich mei ioatdma shpchp ipmi_si ipmi_devintf ipmi_msghandler wmi acpi_power_meter acpi_pad dm_multipath hangcheck_timer ip_tables ext4 mbcache jbd2 mlx4_en
  sd_mod crc_t10dif crct10dif_generic mgag200 drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm mlx4_core crct10dif_pclmul crct10dif_common hfi1(OE) igb crc32c_intel rdmavt(OE) ahci ib_core libahci libata ptp megaraid_sas pps_core dca i2c_algo_bit i2c_core devlink dm_mirror dm_region_hash dm_log dm_mod
  CPU: 23 PID: 0 Comm: swapper/23 Tainted: P OE ------------ 3.10.0-693.el7.x86_64 #1
  Hardware name: Intel Corporation S2600CWR/S2600CWR, BIOS SE5C610.86B.01.01.0028.121720182203 12/17/2018
  task: ffff8808f4ec4f10 ti: ffff8808f4ed8000 task.ti: ffff8808f4ed8000
  RIP: 0010:[ffffffff810a65f2] [ffffffff810a65f2] __queue_work+0x32/0x3c0
  RSP: 0018:ffff88105df43d48 EFLAGS: 00010046
  RAX: 0000000000000086 RBX: 0000000000000086 RCX: 0000000000000000
  RDX: ffff880f74e758b0 RSI: 0000000000000000 RDI: 000000000000001f
  RBP: ffff88105df43d80 R08: ffff8808f3c583c8 R09: ffff8808f3c58000
  R10: 0000000000000002 R11: ffff88105df43da8 R12: ffff880f74e758b0
  R13: 000000000000001f R14: 0000000000000000 R15: ffff88105a300000
  FS: 0000000000000000(0000) GS:ffff88105df40000(0000) knlGS:0000000000000000
  CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  CR2: 0000000000000102 CR3: 00000000019f2000 CR4: 00000000001407e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
  Stack:
  ffff88105b6dd708 0000001f00000286 0000000000000086 ffff88105a300000
  ffff880f74e75800 0000000000000000 ffff88105a300000 ffff88105df43d98
  ffffffff810a6b85 ffff88105a301e80 ffff88105df43dc8 ffffffffc0224cde
  Call Trace:
  IRQ

  [ffffffff810a6b85] queue_work_on+0x45/0x50
  [ffffffffc0224cde] _hfi1_schedule_send+0x6e/0xc0 [hfi1]
  [ffffffffc0170570] ? get_map_page+0x60/0x60 [rdmavt]
  [ffffffffc0224d62] hfi1_schedule_send+0x32/0x70 [hfi1]
  [ffffffffc0170644] rvt_rc_timeout+0xd4/0x120 [rdmavt]
  [ffffffffc0170570] ? get_map_page+0x60/0x60 [rdmavt]
  [ffffffff81097316] call_timer_fn+0x36/0x110
  [ffffffffc0170570] ? get_map_page+0x60/0x60 [rdmavt]
  [ffffffff8109982d] run_timer_softirq+0x22d/0x310
  [ffffffff81090b3f] __do_softirq+0xef/0x280
  [ffffffff816b6a5c] call_softirq+0x1c/0x30
  [ffffffff8102d3c5] do_softirq+0x65/0xa0
  [ffffffff81090ec5] irq_exit+0x105/0x110
  [ffffffff816b76c2] smp_apic_timer_interrupt+0x42/0x50
  [ffffffff816b5c1d] apic_timer_interrupt+0x6d/0x80
  EOI

  [ffffffff81527a02] ? cpuidle_enter_state+0x52/0xc0
  [ffffffff81527b48] cpuidle_idle_call+0xd8/0x210
  [ffffffff81034fee] arch_cpu_idle+0xe/0x30
  [ffffffff810e7bca] cpu_startup_entry+0x14a/0x1c0
  [ffffffff81051af6] start_secondary+0x1b6/0x230
  Code: 89 e5 41 57 41 56 49 89 f6 41 55 41 89 fd 41 54 49 89 d4 53 48 83 ec 10 89 7d d4 9c 58 0f 1f 44 00 00 f6 c4 02 0f 85 be 02 00 00 41 f6 86 02 01 00 00 01 0f 85 58 02 00 00 49 c7 c7 28 19 01 00
  RIP [ffffffff810a65f2] __queue_work+0x32/0x3c0
  RSP ffff88105df43d48
  CR2: 0000000000000102

The solution is to reset the QPs before the device resources are freed.
This reset will change the QP state to prevent post sends and delete
timers to prevent callbacks.

Fixes: 0acb0cc7ecc1 ("IB/rdmavt: Initialize and teardown of qpn table")
Link: https://lore.kernel.org/r/20200210131040.87408.38161.stgit@awfm-01.aw.intel.com
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Kaike Wan <kaike.wan@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>