review.tizen.org Git - platform/kernel/linux-starfive.git/log

Merge remote-tracking branch 'regulator/for-5.14' into regulator-next

Merge remote-tracking branch 'regulator/for-5.13' into regulator-linus

regulator: bd9576: Fix uninitializes variable may_have_irqs

The boolean variable may_have_irqs is not ininitialized and is
only being set to true in the case where chip is ROHM_CHIP_TYPE_BD9576.
Fix this by ininitialized may_have_irqs to false.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: e7bf1fa58c46 ("regulator: bd9576: Support error reporting")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/20210622144730.22821-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: max8893: Select REGMAP_I2C to fix build error

Fix build error if REGMAP_I2C is not set.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210622141526.472175-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: da9052: Ensure enough delay time for .set_voltage_time_sel

Use DIV_ROUND_UP to prevent truncation by integer division issue.
This ensures we return enough delay time.

Also fix returning negative value when new_sel < old_sel.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210618141412.4014912-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: mt6358: Fix vdram2 .vsel_mask

The valid vsel value are 0 and 12, so the .vsel_mask should be 0xf.

Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/1624424169-510-1-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi6421v600: Fix setting wrong driver_data

Current code set "config.driver_data = sreg" but sreg only init the mutex,
the othere fields are just zero. Fix it by pass *info to config.driver_data
so each regulator can get corresponding data by rdev_get_drvdata().

Separate enable_mutex from struct hi6421_spmi_reg_info since only need one
mutex for the driver.

Fixes: d2dfd50a0b57 ("staging: hikey9xx: hi6421v600-regulator: move LDO config from DT")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210622043329.392072-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge series "regulator: qcom,rpmh-regulator: Add support for pmic available on SA8155p-adp board" from Bhupesh Sharma <bhupesh.sharma@linaro.org>:

Changes since v2:
-----------------
- v2 series can be found here: https://lore.kernel.org/linux-arm-msm/20210615074543.26700-1-bhupesh.sharma@linaro.org/T/#m8303d27d561b30133992da88198abb78ea833e21
- Addressed review comments from Bjorn and Mark.
- As per suggestion from Bjorn, seperated the patches in different
  patchsets (specific to each subsystem) to ease review and patch application.

Changes since v1:
-----------------
- v1 series can be found here: https://lore.kernel.org/linux-arm-msm/20210607113840.15435-1-bhupesh.sharma@linaro.org/T/#mc524fe82798d4c4fb75dd0333318955e0406ad18
- Addressed review comments from Bjorn and Vinod received on the v1
  series.

This series adds the regulator support code for SA8155p-adp board
which is based on Qualcomm snapdragon sa8155p SoC which in turn is
simiar to the sm8150 SoC.

This board supports a new PMIC PMM8155AU.

While at it, also make some cosmetic changes to the regulator driver
and dt-bindings to make sure the compatibles are alphabetical and also
fix issues with extra comma(s) at the end of terminator line(s).

Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Bhupesh Sharma (5):
  dt-bindings: regulator: qcom,rpmh-regulator: Arrange compatibles
    alphabetically
  dt-bindings: regulator: qcom,rpmh-regulator: Add compatible for
    SA8155p-adp board pmic
  regulator: qcom-rpmh: Cleanup terminator line commas
  regulator: qcom-rpmh: Add terminator at the end of pm7325x_vreg_data[]
    array
  regulator: qcom-rpmh: Add new regulator found on SA8155p adp board

.../regulator/qcom,rpmh-regulator.yaml        | 17 ++---
drivers/regulator/qcom-rpmh-regulator.c       | 62 +++++++++++++++----
2 files changed, 59 insertions(+), 20 deletions(-)

--
2.31.1

Merge series "Extend regulator notification support" from Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>:

Extend regulator notification support

This series extends the regulator notification and error flag support.
Initial discussion on the topic can be found here:
https://lore.kernel.org/lkml/6046836e22b8252983f08d5621c35ececb97820d.camel@fi.rohmeurope.com/

In a nutshell - the series adds:

1. WARNING level events/error flags. (Patch 3)
  Current regulator 'ERROR' event notifications for over/under
  voltage, over current and over temperature are used to indicate
  condition where monitored entity is so badly "off" that it actually
  indicates a hardware error which can not be recovered. The most
  typical hanling for that is believed to be a (graceful)
  system-shutdown. Here we add set of 'WARNING' level flags to allow
  sending notifications to consumers before things are 'that badly off'
  so that consumer drivers can implement recovery-actions.
2. Device-tree properties for specifying limit values. (Patches 1, 5)
  Add limits for above mentioned 'ERROR' and 'WARNING' levels (which
  send notifications to consumers) and also for a 'PROTECTION' level
  (which will be used to immediately shut-down the regulator(s) W/O
  informing consumer drivers. Typically implemented by hardware).
  Property parsing is implemented in regulator core which then calls
  callback operations for limit setting from the IC drivers. A
  warning is emitted if protection is requested by device tree but the
  underlying IC does not support configuring requested protection.
3. Helpers which can be registered by IC. (Patch 4)
  Target is to avoid implementing IRQ handling and IRQ storm protection
  in each IC driver. (Many of the ICs implementin these IRQs do not allow
  masking or acking the IRQ but keep the IRQ asserted for the whole
  duration of problem keeping the processor in IRQ handling loop).
4. Emergency poweroff function (refactored out of the thermal_core to
  kernel/reboot.c) which is called if IC fires error IRQs but IC reading
  fails and given retry-count is exceeded. (Patches 2, 4)
  Please note that the mutex in the emergency shutdown was replaced by a
  simple atomic in order to allow call from any context.

The helper was attempted to be done so it could be used to implement
roughly same logic as is used in qcom-labibb regulator. This means
amongst other things a safety shut-down if IC registers are not readable.
Using these shut-down retry counters are optional. The idea is that the
helper could be also used by simpler ICs which do not provide status
register(s) which can be used to check if error is still active.

ICs which do not have such status register can simply omit the 'renable'
callback (and retry-counts etc) - and helper assumes the situation is Ok
and re-enables IRQ after given time period. If problem persists the
handler is ran again and another notification is sent - but at least the
delay allows processor to avoid IRQ loop.

Patch 7 takes this notification support in use at BD9576MUF.
Patch 8 is related to MFD change which is not really related to the RFC
here. It was added to this series in order to avoid potential conflicts.
Patch 9 adds a maintainers entry.

Changelog v10-RESEND:
   - rebased on v5.13-rc4
Changelog v10:
   - rebased on v5.13-rc2
   - Move rdev_*() print macros to the internal.h and use rdev_dbg()
     from irq_helpers.c
   - Export rdev_get_name() and move it from coupler.h to driver.h for
     others to use. (It was already in coupler.h but not exported -
     usage was limited and coupler.h does not sound like optimal place
     as rdev_name is not only used by coupled regulators)
   - Send all regulator notifications from irq_helpers.c at one OR'd
     event for the sake of simplicity. For BD9576 this does not matter
     as it has own IRQ for each event case. Header defining events says
     they may be OR'd.
   - Change WARN() at protection shutdown to pr_emerg as suggested by
     Petr.
Changelog v9:
   - rebases on v5.13-rc1
   - Update thermal documentation
   - Fix regulator notification event number
Changelog v8:
   - split shutdown API adding and thermal core taking it in use to
     own patches.
   - replace the spinlock with atomic when ensuring the emergency
     shutdown is only called once.
Changelog v7:
  general:
   - rebased on v5.12-rc7
   - new patch for refactoring the hw-failure reboot logic out of
     thermal_core.c for others to use.
  notification helpers:
   - fix regulator error_flags query
   - grammar/typos
   - do not BUG() but attempt to shut-down the system
   - use BITS_PER_TYPE()

Changelog v6:
  Add MAINTAINERS entry
  Changes to IRQ notifiers
   - move devm functions to drivers/regulator/devres.c
   - drop irq validity check
   - use devm_add_action_or_reset()
   - fix styling issues
   - fix kerneldocs

Changelog v5:
   - Fix the badly formatted pr_emerg() call.

Changelog v4:
   - rebased on v5.12-rc6
   - dropped RFC
   - fix external FET DT-binding.
   - improve prints for cases when expecting HW failure.
   - styling and typos

Changelog v3:
  Regulator core:
   - Fix dangling pointer access at regulator_irq_helper()
  stpmic1_regulator:
   - fix function prototype (compile error)
  bd9576-regulator:
   - Update over current limits to what was given in new data-sheet
     (REV00K)
   - Allow over-current monitoring without external FET. Set limits to
     values given in data-sheet (REV00K).

Changelog v2:
  Generic:
  - rebase on v5.12-rc2 + BD9576 series
  - Split devm variant of delayed wq to own series
  Regulator framework:
  - Provide non devm variant of IRQ notification helpers
  - shorten dt-property names as suggested by Rob
  - unconditionally call map_event in IRQ handling and require it to be
    populated
  BD9576 regulators:
  - change the FET resistance property to micro-ohms
  - fix voltage computation in OC limit setting

MAINTAINERS: Add reviewer for regulator irq_helpers

Add a reviewer entry for the regulator irq_helpers.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/2a4286ed98fd69b2539919e6a3e84d2e9804b4da.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: bd9576: Fix the driver name in id table

Driver name was changed in MFD cell:
https://lore.kernel.org/lkml/560b9748094392493ebf7af11b6cc558776c4fd5.1613031055.git.matti.vaittinen@fi.rohmeurope.com/
Fix the ID table to match this.

Fixes: b1b3ced38979 ("mfd: Support ROHM BD9576MUF and BD9573MUF")
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/e0483149333626b3bea298f305cf2809429d1822.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: bd9576: Support error reporting

BD9573 and BD9576 support set of "protection" interrupts for "fatal"
issues. Those lead to SOC reset as PMIC shuts the power outputs. Thus
there is no relevant IRQ handling for them.

Few "detection" interrupts were added to the BD9576 with the idea that
SOC could take some recovery-action before error gets unrecoverable.

Add support for over and under voltage detection for Vout1 ... Vout4
and VoutL1. Add over-current detection for VoutS1 and finally a
thermal warning (common for all regulators) which alerts 30 C
before temperature reaches the thermal shutdown point. This way
consumer drivers can build error-recovery mechanisms.

Unfortunately the BD9576 interrupt logic was not re-evaluated. IRQs
are not designed to be properly acknowleged - and IRQ line is kept
active for whole duration of error condition (in comparison to
informing only about state change).

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/05c4f7a8e30ef1d4d5f3ceab07da4ebe68f5b4ed.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: bd9576 add FET ON-resistance for OCW

BD9576MUF provides over-current protection and detection. Current is
measured as voltage loss over external FET. Allow specifying FET's on
resistance so current monitoring limits can be converted to voltages.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/e5feb160d7e09f33fff5b88f1928c66a15c6680f.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: add property parsing and callbacks to set protection limits

Add DT property parsing code and setting callback for regulator over/under
voltage, over-current and temperature error limits.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/e7b8007ba9eae7076178bf3363fb942ccb1cc9a5.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: IRQ based event/error notification helpers

Provide helper function for IC's implementing regulator notifications
when an IRQ fires. The helper also works for IRQs which can not be acked.
Helper can be set to disable the IRQ at handler and then re-enabling it
on delayed work later. The helper also adds regulator_get_error_flags()
errors in cache for the duration of IRQ disabling.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/ebdf86d8c22b924667ec2385330e30fcbfac0119.1622628334.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: move rdev_print helpers to internal.h

The rdev print helpers are a nice way to print messages related to a
specific regulator device. Move them from core.c to internal.h

As the rdev print helpers use rdev_get_name() export it from core.c. Also
move the declaration from coupler.h to driver.h because the rdev name is
not just a coupled regulator property. I guess the main audience for
rdev_get_name() will be the regulator core and drivers.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/dc7fd70dc31de4d0e820b7646bb78eeb04f80735.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: add warning flags

Add 'warning' level events and error flags to regulator core.
Current regulator core notifications are used to inform consumers
about errors where HW is misbehaving in such way it is assumed to
be broken/unrecoverable.

There are PMICs which are designed for system(s) that may have use
for regulator indications sent before HW is damaged so that some
board/consumer specific recovery-event can be performed while
continuing most of the normal operations.

Add new WARNING level events and notifications to be used for
that purpose.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/9b54aa5589ae4b5945d53d114bac3fae55fa4818.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

thermal: Use generic HW-protection shutdown API

The hardware shutdown function was exported from kernel/reboot for
other subsystems to use. Logic is copied from the thermal_core. The
protection mutex is replaced by an atomic_t to allow calls also from
an IRQ context. Also the WARN() was replaced by pr_emerg() based on
discussions here:
https://lore.kernel.org/lkml/YJuPwAZroVZ%2Fw633@alley/
and here:
https://lore.kernel.org/linux-iommu/20210331093104.383705-4-geert+renesas@glider.be/

Use the exported API instead of implementing own just for the
thermal_core.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/5531e89d9e710f5d10e7cdce3ee58957335b9e03.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

reboot: Add hardware protection power-off

There can be few cases when we need to shut-down the system in order to
protect the hardware. Currently this is done at least by the thermal core
when temperature raises over certain limit.

Some PMICs can also generate interrupts for example for over-current or
over-voltage, voltage drops, short-circuit, ... etc. On some systems
these are a sign of hardware failure and only thing to do is try to
protect the rest of the hardware by shutting down the system.

Add shut-down logic which can be used by all subsystems instead of
implementing the shutdown in each subsystem. The logic is stolen from
thermal_core with difference of using atomic_t instead of a mutex in
order to allow calls directly from IRQ context and changing the WARN()
to pr_emerg() as discussed here:
https://lore.kernel.org/lkml/YJuPwAZroVZ%2Fw633@alley/
and here:
https://lore.kernel.org/linux-iommu/20210331093104.383705-4-geert+renesas@glider.be/

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/e83ec1ca9408f90c857ea9dcdc57b14d9037b03f.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: Add protection limit properties

Support specifying protection/error/warning limits for regulator
over current, over temperature and over/under voltage.

Most of the PMICs support only "protection" feature but few
setups do also support error/warning level indications.

On many ICs most of the protection limits can't actually be set.
But for example the ampere limit for over-current protection on ROHM
BD9576 can be configured - or feature can be completely disabled.

Provide limit setting for all protections/errors for the sake of
the completeness and do that using own properties for all so that
not all users would need to set all levels when only one or few are
supported.

Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/ae2c6056d5ed1334912d27e736d23c9151065433.1622628333.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi6421v600: Fix setting idle mode

commit db27f8294cd7 changed eco_mode << (ffs(sreg->eco_mode_mask) - 1)
to sreg->eco_mode_mask << (ffs(sreg->eco_mode_mask) - 1) which is wrong.
Fix it by simply set val = sreg->eco_mode_mask.

In additional, sreg->eco_mode_mask can be 0 (LDO3, LDO33, LDO34).
Return -EINVAL if idle mode is not supported when sreg->eco_mode_mask is 0.

While at it, also use unsigned int for reg_val/val which is the expected
type for regmap_read and regmap_update_bits.

Fixes: db27f8294cd7 ("staging: regulator: hi6421v600-regulator: use shorter names for OF properties")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210619123423.4091429-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: Add MAX8893 bindings

Add Maxim MAX8893 PMIC device tree bindings. The example is also
provided.

Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Link: https://lore.kernel.org/r/20210618141607.884-2-cerg2010cerg2010@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: max8893: add regulator driver

MAX8893 is a simple regulator which can be found on some of Sasmsung
phones.

Signed-off-by: Sergey Larin <cerg2010cerg2010@mail.ru>
Link: https://lore.kernel.org/r/20210618141607.884-1-cerg2010cerg2010@mail.ru
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi6421: Use correct variable type for regmap api val argument

Use unsigned int instead of u32 for regmap_read/regmap_update_bits val
argument.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210619124133.4096683-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: qcom,rpmh-regulator: Add compatible for SA8155p-adp board pmic

Add compatible string for pmm8155au pmic found on
the SA8155p-adp board.

Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210617051712.345372-3-bhupesh.sharma@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: qcom,rpmh-regulator: Arrange compatibles alphabetically

Arrange the compatibles inside qcom-rpmh regulator device tree
bindings alphabetically.

Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210617051712.345372-2-bhupesh.sharma@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: qcom-rpmh: Add new regulator found on SA8155p adp board

SA8155p-adp board supports a new regulator - pmm8155au.

The output power management circuits in this regulator include:
- FTS510 smps,
- HFS510 smps, and
- LDO510 linear regulators

Add support for the same.

Cc: Mark Brown <broonie@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210617051712.345372-6-bhupesh.sharma@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: qcom-rpmh: Add terminator at the end of pm7325x_vreg_data[] array

Add missing terminator(s) at the end of pm7325x_vreg_data[]
array instances.

Fixes: c4e5aa3dbee5 ("regulator: qcom-rpmh: Add PM7325/PMR735A regulator support")
Cc: Mark Brown <broonie@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210617051712.345372-5-bhupesh.sharma@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: qcom-rpmh: Cleanup terminator line commas

Cleanup the qcom-rpmh regulator driver to remove comma(s)
at the end of the terminator line(s).

Cc: Mark Brown <broonie@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Link: https://lore.kernel.org/r/20210617051712.345372-4-bhupesh.sharma@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: hi655x: Fix pass wrong pointer to config.driver_data

Current code sets config.driver_data to a zero initialized regulator
which is obviously wrong. Fix it.

Fixes: 4618119b9be5 ("regulator: hi655x: enable regulator for hi655x PMIC")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20210620132715.60215-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 5.13-rc7

Merge tag 'sched_urgent_for_v5.13_rc6' of git://git./linux/kernel/git/tip/tip

Pull scheduler fix from Borislav Petkov:
"A single fix to restore fairness between control groups with equal
priority"

* tag 'sched_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Correctly insert cfs_rq's to list on unthrottle

Merge tag 'irq_urgent_for_v5.13_rc6' of git://git./linux/kernel/git/tip/tip

Pull irq fix from Borislav Petkov:
"A single fix for GICv3 to not take an interrupt in an NMI context"

* tag 'irq_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3: Workaround inconsistent PMR setting on NMI entry

Merge tag 'x86_urgent_for_v5.13_rc6' of git://git./linux/kernel/git/tip/tip

Pull x86 fixes from Borislav Petkov:
"A first set of urgent fixes to the FPU/XSTATE handling mess^W code.
  (There's a lot more in the pipe):

   - Prevent corruption of the XSTATE buffer in signal handling by
     validating what is being copied from userspace first.

   - Invalidate other task's preserved FPU registers on XRSTOR failure
     (#PF) because latter can still modify some of them.

   - Restore the proper PKRU value in case userspace modified it

   - Reset FPU state when signal restoring fails

  Other:

   - Map EFI boot services data memory as encrypted in a SEV guest so
     that the guest can access it and actually boot properly

   - Two SGX correctness fixes: proper resources freeing and a NUMA fix"

* tag 'x86_urgent_for_v5.13_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Avoid truncating memblocks for SGX memory
  x86/sgx: Add missing xa_destroy() when virtual EPC is destroyed
  x86/fpu: Reset state for all signal restore failures
  x86/pkru: Write hardware init value to PKRU when xstate is init
  x86/process: Check PF_KTHREAD and not current->mm for kernel threads
  x86/fpu: Invalidate FPU state after a failed XRSTOR from a user buffer
  x86/fpu: Prevent state corruption in __fpu__restore_sig()
  x86/ioremap: Map EFI-reserved memory as encrypted for SEV

Merge tag 'powerpc-5.13-6' of git://git./linux/kernel/git/powerpc/linux

Pull powerpc fixes from Michael Ellerman:
"Fix initrd corruption caused by our recent change to use relative jump
  labels.

  Fix a crash using perf record on systems without a hardware PMU
  backend.

  Rework our 64-bit signal handling slighty to make it more closely
  match the old behaviour, after the recent change to use unsafe user
  accessors.

  Thanks to Anastasia Kovaleva, Athira Rajeev, Christophe Leroy, Daniel
  Axtens, Greg Kurz, and Roman Bolshakov"

* tag 'powerpc-5.13-6' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/perf: Fix crash in perf_instruction_pointer() when ppmu is not set
  powerpc: Fix initrd corruption with relative jump labels
  powerpc/signal64: Copy siginfo before changing regs->nip
  powerpc/mem: Add back missing header to fix 'no previous prototype' error

Merge tag 'perf-tools-fixes-for-v5.13-2021-06-19' of git://git./linux/kernel/git/acme/linux

Pull perf tools fixes from Arnaldo Carvalho de Melo:

- Fix refcount usage when processing PERF_RECORD_KSYMBOL.

- 'perf stat' metric group fixes.

- Fix 'perf test' non-bash issue with stat bpf counters.

- Update unistd, in.h and socket.h with the kernel sources, silencing
   perf build warnings.

* tag 'perf-tools-fixes-for-v5.13-2021-06-19' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
  tools headers UAPI: Sync linux/in.h copy with the kernel sources
  tools headers UAPI: Sync asm-generic/unistd.h with the kernel original
  perf beauty: Update copy of linux/socket.h with the kernel sources
  perf test: Fix non-bash issue with stat bpf counters
  perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL
  perf metricgroup: Return error code from metricgroup__add_metric_sys_event_iter()
  perf metricgroup: Fix find_evsel_group() event selector

Merge tag 'riscv-for-linus-5.13-rc7' of git://git./linux/kernel/git/riscv/linux

Pull RISC-V fixes from Palmer Dabbelt:

- A build fix to always build modules with the 'medany' code model, as
   the module loader doesn't support 'medlow'.

- A Kconfig warning fix for the SiFive errata.

- A pair of fixes that for regressions to the recent memory layout
   changes.

- A fix for the FU740 device tree.

* tag 'riscv-for-linus-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: dts: fu740: fix cache-controller interrupts
  riscv: Ensure BPF_JIT_REGION_START aligned with PMD size
  riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name
  riscv: sifive: fix Kconfig errata warning
  riscv32: Use medany C model for modules

Merge tag 's390-5.13-4' of git://git./linux/kernel/git/s390/linux

Pull s390 fixes from Vasily Gorbik:

- Fix zcrypt ioctl hang due to AP queue msg counter dropping below 0
   when pending requests are purged.

- Two fixes for the machine check handler in the entry code.

* tag 's390-5.13-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/ap: Fix hanging ioctl caused by wrong msg counter
  s390/mcck: fix invalid KVM guest condition check
  s390/mcck: fix calculation of SIE critical section size

tools headers UAPI: Sync linux/in.h copy with the kernel sources

To pick the changes in:

  321827477360934d ("icmp: don't send out ICMP messages with a source address of 0.0.0.0")

That don't result in any change in tooling, as INADDR_ are not used to
generate id->string tables used by 'perf trace'.

This addresses this build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/linux/in.h' differs from latest version at 'include/uapi/linux/in.h'
  diff -u tools/include/uapi/linux/in.h include/uapi/linux/in.h

Cc: David S. Miller <davem@davemloft.net>
Cc: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

tools headers UAPI: Sync asm-generic/unistd.h with the kernel original

To pick the changes in:

  8b1462b67f23da54 ("quota: finish disable quotactl_path syscall")

Those headers are used in some arches to generate the syscall table used
in 'perf trace' to translate syscall numbers into strings.

This addresses this perf build warning:

  Warning: Kernel ABI header at 'tools/include/uapi/asm-generic/unistd.h' differs from latest version at 'include/uapi/asm-generic/unistd.h'
  diff -u tools/include/uapi/asm-generic/unistd.h include/uapi/asm-generic/unistd.h

Cc: Jan Kara <jack@suse.cz>
Cc: Marcin Juszkiewicz <marcin@juszkiewicz.com.pl>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf beauty: Update copy of linux/socket.h with the kernel sources

To pick the changes in:

  ea6932d70e223e02 ("net: make get_net_ns return error if NET_NS is disabled")

That don't result in any changes in the tables generated from that
header.

This silences this perf build warning:

  Warning: Kernel ABI header at 'tools/perf/trace/beauty/include/linux/socket.h' differs from latest version at 'include/linux/socket.h'
  diff -u tools/perf/trace/beauty/include/linux/socket.h include/linux/socket.h

Cc: Changbin Du <changbin.du@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf test: Fix non-bash issue with stat bpf counters

$(( .. )) is a bash feature but the test's interpreter is !/bin/sh,
switch the code to use expr.

Signed-off-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <songliubraving@fb.com>
Cc: bpf@vger.kernel.org
Link: http://lore.kernel.org/lkml/20210617184216.2075588-1-irogers@google.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf machine: Fix refcount usage when processing PERF_RECORD_KSYMBOL

ASan reported a memory leak of BPF-related ksymbols map and dso. The
leak is caused by refount never reaching 0, due to missing __put calls
in the function machine__process_ksymbol_register.

Once the dso is inserted in the map, dso__put() should be called
(map__new2() increases the refcount to 2).

The same thing applies for the map when it's inserted into maps
(maps__insert() increases the refcount to 2).

  $ sudo ./perf record -- sleep 5
  [ perf record: Woken up 1 times to write data ]
  [ perf record: Captured and wrote 0.025 MB perf.data (8 samples) ]

  =================================================================
  ==297735==ERROR: LeakSanitizer: detected memory leaks

  Direct leak of 6992 byte(s) in 19 object(s) allocated from:
      #0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
      #1 0x8e4e53 in map__new2 /home/user/linux/tools/perf/util/map.c:216:20
      #2 0x8cf68c in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:778:10
      [...]

  Indirect leak of 8702 byte(s) in 19 object(s) allocated from:
      #0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
      #1 0x8728d7 in dso__new_id /home/user/linux/tools/perf/util/dso.c:1256:20
      #2 0x872015 in dso__new /home/user/linux/tools/perf/util/dso.c:1295:9
      #3 0x8cf623 in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:774:21
      [...]

  Indirect leak of 1520 byte(s) in 19 object(s) allocated from:
      #0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
      #1 0x87b3da in symbol__new /home/user/linux/tools/perf/util/symbol.c:269:23
      #2 0x888954 in map__process_kallsym_symbol /home/user/linux/tools/perf/util/symbol.c:710:8
      [...]

  Indirect leak of 1406 byte(s) in 19 object(s) allocated from:
      #0 0x4f43c7 in calloc (/home/user/linux/tools/perf/perf+0x4f43c7)
      #1 0x87b3da in symbol__new /home/user/linux/tools/perf/util/symbol.c:269:23
      #2 0x8cfbd8 in machine__process_ksymbol_register /home/user/linux/tools/perf/util/machine.c:803:8
      [...]

Signed-off-by: Riccardo Mancini <rickyman7@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tommi Rantala <tommi.t.rantala@nokia.com>
Link: http://lore.kernel.org/lkml/20210612173751.188582-1-rickyman7@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf metricgroup: Return error code from metricgroup__add_metric_sys_event_iter()

The error code is not set at all in the sys event iter function.

This may lead to an uninitialized value of "ret" in
metricgroup__add_metric() when no CPU metric is added.

Fix by properly setting the error code.

It is not necessary to init "ret" to 0 in metricgroup__add_metric(), as
if we have no CPU or sys event metric matching, then "has_match" should
be 0 and "ret" is set to -EINVAL.

However gcc cannot detect that it may not have been set after the
map_for_each_metric() loop for CPU metrics, which is strange.

Fixes: be335ec28efa8 ("perf metricgroup: Support adding metrics for system PMUs")
Signed-off-by: John Garry <john.garry@huawei.com>
Acked-by: Ian Rogers <irogers@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/1623335580-187317-3-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

perf metricgroup: Fix find_evsel_group() event selector

The following command segfaults on my x86 broadwell:

  $ ./perf stat  -M frontend_bound,retiring,backend_bound,bad_speculation sleep 1
  WARNING: grouped events cpus do not match, disabling group:
    anon group { raw 0x10e }
    anon group { raw 0x10e }
  perf: util/evsel.c:1596: get_group_fd: Assertion `!(!leader->core.fd)' failed.
  Aborted (core dumped)

The issue shows itself as a use-after-free in evlist__check_cpu_maps(),
whereby the leader of an event selector (evsel) has been deleted (yet we
still attempt to verify for an evsel).

Fundamentally the problem comes from metricgroup__setup_events() ->
find_evsel_group(), and has developed from the previous fix attempt in
commit 9c880c24cb0d ("perf metricgroup: Fix for metrics containing
duration_time").

The problem now is that the logic in checking if an evsel is in the same
group is subtly broken for the "cycles" event. For the "cycles" event,
the pmu_name is NULL; however the logic in find_evsel_group() may set an
event matched against "cycles" as used, when it should not be.

This leads to a condition where an evsel is set, yet its leader is not.

Fix the check for evsel pmu_name by not matching evsels when either has a
NULL pmu_name.

There is still a pre-existing metric issue whereby the ordering of the
metrics may break the 'stat' function, as discussed at:
https://lore.kernel.org/lkml/49c6fccb-b716-1bf0-18a6-cace1cdb66b9@huawei.com/

Fixes: 9c880c24cb0d ("perf metricgroup: Fix for metrics containing duration_time")
Signed-off-by: John Garry <john.garry@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com> # On a Thinkpad T450S
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Ian Rogers <irogers@google.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kajol Jain <kjain@linux.ibm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/1623335580-187317-2-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>

riscv: dts: fu740: fix cache-controller interrupts

The order of interrupt numbers is incorrect.

The order for FU740 is: DirError, DataError, DataFail, DirFail

From SiFive FU740-C000 Manual:
19 - L2 Cache DirError
20 - L2 Cache DirFail
21 - L2 Cache DataError
22 - L2 Cache DataFail

Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>

riscv: Ensure BPF_JIT_REGION_START aligned with PMD size

Andreas reported commit fc8504765ec5 ("riscv: bpf: Avoid breaking W^X")
breaks booting with one kind of defconfig, I reproduced a kernel panic
with the defconfig:

[    0.138553] Unable to handle kernel paging request at virtual address ffffffff81201220
[    0.139159] Oops [#1]
[    0.139303] Modules linked in:
[    0.139601] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.13.0-rc5-default+ #1
[    0.139934] Hardware name: riscv-virtio,qemu (DT)
[    0.140193] epc : __memset+0xc4/0xfc
[    0.140416]  ra : skb_flow_dissector_init+0x1e/0x82
[    0.140609] epc : ffffffff8029806c ra : ffffffff8033be78 sp : ffffffe001647da0
[    0.140878]  gp : ffffffff81134b08 tp : ffffffe001654380 t0 : ffffffff81201158
[    0.141156]  t1 : 0000000000000002 t2 : 0000000000000154 s0 : ffffffe001647dd0
[    0.141424]  s1 : ffffffff80a43250 a0 : ffffffff81201220 a1 : 0000000000000000
[    0.141654]  a2 : 000000000000003c a3 : ffffffff81201258 a4 : 0000000000000064
[    0.141893]  a5 : ffffffff8029806c a6 : 0000000000000040 a7 : ffffffffffffffff
[    0.142126]  s2 : ffffffff81201220 s3 : 0000000000000009 s4 : ffffffff81135088
[    0.142353]  s5 : ffffffff81135038 s6 : ffffffff8080ce80 s7 : ffffffff80800438
[    0.142584]  s8 : ffffffff80bc6578 s9 : 0000000000000008 s10: ffffffff806000ac
[    0.142810]  s11: 0000000000000000 t3 : fffffffffffffffc t4 : 0000000000000000
[    0.143042]  t5 : 0000000000000155 t6 : 00000000000003ff
[    0.143220] status: 0000000000000120 badaddr: ffffffff81201220 cause: 000000000000000f
[    0.143560] [<ffffffff8029806c>] __memset+0xc4/0xfc
[    0.143859] [<ffffffff8061e984>] init_default_flow_dissectors+0x22/0x60
[    0.144092] [<ffffffff800010fc>] do_one_initcall+0x3e/0x168
[    0.144278] [<ffffffff80600df0>] kernel_init_freeable+0x1c8/0x224
[    0.144479] [<ffffffff804868a8>] kernel_init+0x12/0x110
[    0.144658] [<ffffffff800022de>] ret_from_exception+0x0/0xc
[    0.145124] ---[ end trace f1e9643daa46d591 ]---

After some investigation, I think I found the root cause: commit
2bfc6cd81bd ("move kernel mapping outside of linear mapping") moves
BPF JIT region after the kernel:

| #define BPF_JIT_REGION_START PFN_ALIGN((unsigned long)&_end)

The &_end is unlikely aligned with PMD size, so the front bpf jit
region sits with part of kernel .data section in one PMD size mapping.
But kernel is mapped in PMD SIZE, when bpf_jit_binary_lock_ro() is
called to make the first bpf jit prog ROX, we will make part of kernel
.data section RO too, so when we write to, for example memset the
.data section, MMU will trigger a store page fault.

To fix the issue, we need to ensure the BPF JIT region is PMD size
aligned. This patch acchieve this goal by restoring the BPF JIT region
to original position, I.E the 128MB before kernel .text section. The
modification to kasan_init.c is inspired by Alexandre.

Fixes: fc8504765ec5 ("riscv: bpf: Avoid breaking W^X")
Reported-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>

riscv: kasan: Fix MODULES_VADDR evaluation due to local variables' name

commit 2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear
mapping") makes use of MODULES_VADDR to populate kernel, BPF, modules
mapping. Currently, MODULES_VADDR is defined as below for RV64:

| #define MODULES_VADDR (PFN_ALIGN((unsigned long)&_end) - SZ_2G)

But kasan_init() has two local variables which are also named as _start,
_end, so MODULES_VADDR is evaluated with the local variable _end
rather than the global "_end" as we expected. Fix this issue by
renaming the two local variables.

Fixes: 2bfc6cd81bd1 ("riscv: Move kernel mapping outside of linear mapping")
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>

Merge tag 'net-5.13-rc7' of git://git./linux/kernel/git/netdev/net

Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc7, including fixes from wireless, bpf,
  bluetooth, netfilter and can.

  Current release - regressions:

   - mlxsw: spectrum_qdisc: Pass handle, not band number to find_class()
     to fix modifying offloaded qdiscs

   - lantiq: net: fix duplicated skb in rx descriptor ring

   - rtnetlink: fix regression in bridge VLAN configuration, empty info
     is not an error, bot-generated "fix" was not needed

   - libbpf: s/rx/tx/ typo on umem->rx_ring_setup_done to fix umem
     creation

  Current release - new code bugs:

   - ethtool: fix NULL pointer dereference during module EEPROM dump via
     the new netlink API

   - mlx5e: don't update netdev RQs with PTP-RQ, the special purpose
     queue should not be visible to the stack

   - mlx5e: select special PTP queue only for SKBTX_HW_TSTAMP skbs

   - mlx5e: verify dev is present in get devlink port ndo, avoid a panic

  Previous releases - regressions:

   - neighbour: allow NUD_NOARP entries to be force GCed

   - further fixes for fallout from reorg of WiFi locking (staging:
     rtl8723bs, mac80211, cfg80211)

   - skbuff: fix incorrect msg_zerocopy copy notifications

   - mac80211: fix NULL ptr deref for injected rate info

   - Revert "net/mlx5: Arm only EQs with EQEs" it may cause missed IRQs

  Previous releases - always broken:

   - bpf: more speculative execution fixes

   - netfilter: nft_fib_ipv6: skip ipv6 packets from any to link-local

   - udp: fix race between close() and udp_abort() resulting in a panic

   - fix out of bounds when parsing TCP options before packets are
     validated (in netfilter: synproxy, tc: sch_cake and mptcp)

   - mptcp: improve operation under memory pressure, add missing
     wake-ups

   - mptcp: fix double-lock/soft lookup in subflow_error_report()

   - bridge: fix races (null pointer deref and UAF) in vlan tunnel
     egress

   - ena: fix DMA mapping function issues in XDP

   - rds: fix memory leak in rds_recvmsg

  Misc:

   - vrf: allow larger MTUs

   - icmp: don't send out ICMP messages with a source address of 0.0.0.0

   - cdc_ncm: switch to eth%d interface naming"

* tag 'net-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (139 commits)
  net: ethernet: fix potential use-after-free in ec_bhf_remove
  selftests/net: Add icmp.sh for testing ICMP dummy address responses
  icmp: don't send out ICMP messages with a source address of 0.0.0.0
  net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY
  net: ll_temac: Fix TX BD buffer overwrite
  net: ll_temac: Add memory-barriers for TX BD access
  net: ll_temac: Make sure to free skb when it is completely used
  MAINTAINERS: add Guvenc as SMC maintainer
  bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path
  bnxt_en: Fix TQM fastpath ring backing store computation
  bnxt_en: Rediscover PHY capabilities after firmware reset
  cxgb4: fix wrong shift.
  mac80211: handle various extensible elements correctly
  mac80211: reset profile_periodicity/ema_ap
  cfg80211: avoid double free of PMSR request
  cfg80211: make certificate generation more robust
  mac80211: minstrel_ht: fix sample time check
  net: qed: Fix memcpy() overflow of qed_dcbx_params()
  net: cdc_eem: fix tx fixup skb leak
  net: hamradio: fix memory leak in mkiss_close
  ...

Merge tag 'for-5.13-rc6-tag' of git://git./linux/kernel/git/kdave/linux

Pull btrfs fix from David Sterba:
"One more fix, for a space accounting bug in zoned mode. It happens
  when a block group is switched back rw->ro and unusable bytes (due to
  zoned constraints) are subtracted twice.

  It has user visible effects so I consider it important enough for late
  -rc inclusion and backport to stable"

* tag 'for-5.13-rc6-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: zoned: fix negative space_info->bytes_readonly

Merge tag 'pci-v5.13-fixes-2' of git://git./linux/kernel/git/helgaas/pci

Pull PCI fixes from Bjorn Helgaas:

- Clear 64-bit flag for host bridge windows below 4GB to fix a resource
   allocation regression added in -rc1 (Punit Agrawal)

- Fix tegra194 MCFG quirk build regressions added in -rc1 (Jon Hunter)

- Avoid secondary bus resets on TI KeyStone C667X devices (Antti
   Järvinen)

- Avoid secondary bus resets on some NVIDIA GPUs (Shanker Donthineni)

- Work around FLR erratum on Huawei Intelligent NIC VF (Chiqijun)

- Avoid broken ATS on AMD Navi14 GPU (Evan Quan)

- Trust Broadcom BCM57414 NIC to isolate functions even though it
   doesn't advertise ACS support (Sriharsha Basavapatna)

- Work around AMD RS690 BIOSes that don't configure DMA above 4GB
   (Mikel Rychliski)

- Fix panic during PIO transfer on Aardvark controller (Pali Rohár)

* tag 'pci-v5.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: aardvark: Fix kernel panic during PIO transfer
  PCI: Add AMD RS690 quirk to enable 64-bit DMA
  PCI: Add ACS quirk for Broadcom BCM57414 NIC
  PCI: Mark AMD Navi14 GPU ATS as broken
  PCI: Work around Huawei Intelligent NIC VF FLR erratum
  PCI: Mark some NVIDIA GPUs to avoid bus reset
  PCI: Mark TI C667X to avoid bus reset
  PCI: tegra194: Fix MCFG quirk build regressions
  PCI: of: Clear 64-bit flag for non-prefetchable memory below 4GB

afs: Re-enable freezing once a page fault is interrupted

If a task is killed during a page fault, it does not currently call
sb_end_pagefault(), which means that the filesystem cannot be frozen
at any time thereafter. This may be reported by lockdep like this:

====================================
WARNING: fsstress/10757 still has locks held!
5.13.0-rc4-build4+ #91 Not tainted
------------------------------------
1 lock held by fsstress/10757:
#0: ffff888104eac530
(
sb_pagefaults

as filesystem freezing is modelled as a lock.

Fix this by removing all the direct returns from within the function,
and using 'ret' to indicate whether we were interrupted or successful.

Fixes: 1cf7a1518aef ("afs: Implement shared-writeable mmap")
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/20210616154900.1958373-1-willy@infradead.org/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

net: ethernet: fix potential use-after-free in ec_bhf_remove

static void ec_bhf_remove(struct pci_dev *dev)
{
...
struct ec_bhf_priv *priv = netdev_priv(net_dev);

unregister_netdev(net_dev);
free_netdev(net_dev);

pci_iounmap(dev, priv->dma_io);
pci_iounmap(dev, priv->io);
...
}

priv is netdev private data, but it is used
after free_netdev(). It can cause use-after-free when accessing priv
pointer. So, fix it by moving free_netdev() after pci_iounmap()
calls.

Fixes: 6af55ff52b02 ("Driver for Beckhoff CX5020 EtherCAT master module.")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-net-2021-06-18' of git://git./linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
A couple of straggler fixes:
* a minstrel HT sample check fix
* peer measurement could double-free on races
* certificate file generation at build time could
   sometimes hang
* some parameters weren't reset between connections
   in mac80211
* some extensible elements were treated as non-
   extensible, possibly causuing bad connections
   (or failures) if the AP adds data
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

selftests/net: Add icmp.sh for testing ICMP dummy address responses

This adds a new icmp.sh selftest for testing that the kernel will respond
correctly with an ICMP unreachable message with the dummy (192.0.0.8)
source address when there are no IPv4 addresses configured to use as source
addresses.

Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

icmp: don't send out ICMP messages with a source address of 0.0.0.0

When constructing ICMP response messages, the kernel will try to pick a
suitable source address for the outgoing packet. However, if no IPv4
addresses are configured on the system at all, this will fail and we end up
producing an ICMP message with a source address of 0.0.0.0. This can happen
on a box routing IPv4 traffic via v6 nexthops, for instance.

Since 0.0.0.0 is not generally routable on the internet, there's a good
chance that such ICMP messages will never make it back to the sender of the
original packet that the ICMP message was sent in response to. This, in
turn, can create connectivity and PMTUd problems for senders. Fortunately,
RFC7600 reserves a dummy address to be used as a source for ICMP
messages (192.0.0.8/32), so let's teach the kernel to substitute that
address as a last resort if the regular source address selection procedure
fails.

Below is a quick example reproducing this issue with network namespaces:

ip netns add ns0
ip l add type veth peer netns ns0
ip l set dev veth0 up
ip a add 10.0.0.1/24 dev veth0
ip a add fc00:dead:cafe:42::1/64 dev veth0
ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2
ip -n ns0 l set dev veth0 up
ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0
ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1
ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0
ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1
tcpdump -tpni veth0 -c 2 icmp &
ping -w 1 10.1.0.1 > /dev/null
tcpdump: verbose output suppressed, use -v[v]... for full protocol decode
listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64
IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92
2 packets captured
2 packets received by filter
0 packets dropped by kernel

With this patch the above capture changes to:
IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64
IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Juliusz Chroboczek <jch@irif.fr>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Avoid ndo_start_xmit returning NETDEV_TX_BUSY

As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Fix TX BD buffer overwrite

Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.

This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.

Fixes: 84823ff80f74 ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Add memory-barriers for TX BD access

Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.

In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.

When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.

Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.

Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: ll_temac: Make sure to free skb when it is completely used

With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.

Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.

Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MAINTAINERS: add Guvenc as SMC maintainer

Add Guvenc as maintainer for Shared Memory Communications (SMC)
Sockets.

Cc: Julian Wiedmann <jwi@linux.ibm.com>
Acked-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'bnxt_en-fixes'

Michael Chan says:

====================
bnxt_en: Bug fixes

This patchset includes 3 small bug fixes to reinitialize PHY capabilities
after firmware reset, setup the chip's internal TQM fastpath ring
backing memory properly for RoCE traffic, and to free ethtool related
memory if driver probe fails.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Call bnxt_ethtool_free() in bnxt_init_one() error path

bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.

Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Fix TQM fastpath ring backing store computation

TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring. This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.

Fixes: c7dd7ab4b204 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bnxt_en: Rediscover PHY capabilities after firmware reset

There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.

Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: fix wrong shift.

While fixing coverity warning, commit dd2c79677375 introduced typo in
shift value. Fix that.

Signed-off-by: Pavel Machek (CIP) <pavel@denx.de>
Fixes: dd2c79677375 ("cxgb4: Fix unintentional sign extension issues")
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'arc-5.13-rc7-fixes' of git://git./linux/kernel/git/vgupta/arc

Pull ARC fixes from Vineet Gupta:

- ARCv2 userspace ABI not populating a few registers

- Unbork CONFIG_HARDENED_USERCOPY for ARC

* tag 'arc-5.13-rc7-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: fix CONFIG_HARDENED_USERCOPY
ARCv2: save ABI registers across signal handling

Merge tag 'trace-v5.13-rc6' of git://git./linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:

- Have recordmcount check for valid st_shndx otherwise some archs may
   have invalid references for the mcount location.

- Two fixes done for mapping pids to task names. Traces were not
   showing the names of tasks when they should have.

- Fix to trace_clock_global() to prevent it from going backwards

* tag 'trace-v5.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Do no increment trace_clock_global() by one
  tracing: Do not stop recording comms if the trace file is being read
  tracing: Do not stop recording cmdlines when tracing is off
  recordmcount: Correct st_shndx handling

Merge tag 'printk-for-5.13-fixup' of git://git./linux/kernel/git/printk/linux

Pull printk fixup from Petr Mladek:
"Fix misplaced EXPORT_SYMBOL(vsprintf)"

* tag 'printk-for-5.13-fixup' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: Move EXPORT_SYMBOL() closer to vprintk definition

Merge tag 'pm-5.13-rc7' of git://git./linux/kernel/git/rafael/linux-pm

Pull power management fix from Rafael Wysocki:
"Remove recently added frequency invariance support from the CPPC
  cpufreq driver, because it has turned out to be problematic and it
  cannot be fixed properly on time for 5.13 (Viresh Kumar)"

* tag 'pm-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  Revert "cpufreq: CPPC: Add support for frequency invariance"

Merge tag 'usb-5.13-rc7' of git://git./linux/kernel/git/gregkh/usb

Pull USB fixes from Greg KH:
"Here are three small USB fixes for reported problems for 5.13-rc7.
  They include:

   - disable autosuspend for a cypress USB hub

   - fix the battery charger detection for the chipidea driver

   - fix a kernel panic in the dwc3 driver due to a previous change in
     5.13-rc1.

  All have been in linux-next with no reported problems"

* tag 'usb-5.13-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: core: hub: Disable autosuspend for Cypress CY7C65632
  usb: chipidea: imx: Fix Battery Charger 1.2 CDP detection
  usb: dwc3: core: fix kernel panic when do reboot

x86/mm: Avoid truncating memblocks for SGX memory

tl;dr:

Several SGX users reported seeing the following message on NUMA systems:

  sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.

This turned out to be the memblock code mistakenly throwing away SGX
memory.

=== Full Changelog ===

The 'max_pfn' variable represents the highest known RAM address.  It can
be used, for instance, to quickly determine for which physical addresses
there is mem_map[] space allocated.  The numa_meminfo code makes an
effort to throw out ("trim") all memory blocks which are above 'max_pfn'.

SGX memory is not considered RAM (it is marked as "Reserved" in the
e820) and is not taken into account by max_pfn. Despite this, SGX memory
areas have NUMA affinity and are enumerated in the ACPI SRAT table. The
existing SGX code uses the numa_meminfo mechanism to look up the NUMA
affinity for its memory areas.

In cases where SGX memory was above max_pfn (usually just the one EPC
section in the last highest NUMA node), the numa_memblock is truncated
at 'max_pfn', which is below the SGX memory.  When the SGX code tries to
look up the affinity of this memory, it fails and produces an error message:

  sgx: [Firmware Bug]: Unable to map EPC section to online node. Fallback to the NUMA node 0.

and assigns the memory to NUMA node 0.

Instead of silently truncating the memory block at 'max_pfn' and
dropping the SGX memory, add the truncated portion to
'numa_reserved_meminfo'.  This allows the SGX code to later determine
the NUMA affinity of its 'Reserved' area.

Before, numa_meminfo looked like this (from 'crash'):

  blk = { start =          0x0, end = 0x2080000000, nid = 0x0 }
        { start = 0x2080000000, end = 0x4000000000, nid = 0x1 }

numa_reserved_meminfo is empty.

With this, numa_meminfo looks like this:

  blk = { start =          0x0, end = 0x2080000000, nid = 0x0 }
        { start = 0x2080000000, end = 0x4000000000, nid = 0x1 }

and numa_reserved_meminfo has an entry for node 1's SGX memory:

  blk =  { start = 0x4000000000, end = 0x4080000000, nid = 0x1 }

[ daveh: completely rewrote/reworked changelog ]

Fixes: 5d30f92e7631 ("x86/NUMA: Provide a range-to-target_node lookup facility")
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fan Du <fan.du@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko@kernel.org>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dave Hansen <dave.hansen@intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lkml.kernel.org/r/20210617194657.0A99CB22@viggo.jf.intel.com

Merge tag 'drm-fixes-2021-06-18' of git://anongit.freedesktop.org/drm/drm

Pull drm fixes from Dave Airlie:
"Not much happening in fixes land this week only one PR for two amdgpu
  powergating fixes was waiting for me, maybe something will show up
  over the weekend, maybe not.

  amdgpu:

   - GFX9 and 10 powergating fixes"

* tag 'drm-fixes-2021-06-18' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu/gfx10: enlarge CP_MEC_DOORBELL_RANGE_UPPER to cover full doorbell.
  drm/amdgpu/gfx9: fix the doorbell missing when in CGPG issue.

PCI: aardvark: Fix kernel panic during PIO transfer

Trying to start a new PIO transfer by writing value 0 in PIO_START register
when previous transfer has not yet completed (which is indicated by value 1
in PIO_START) causes an External Abort on CPU, which results in kernel
panic:

SError Interrupt on CPU0, code 0xbf000002 -- SError
Kernel panic - not syncing: Asynchronous SError Interrupt

To prevent kernel panic, it is required to reject a new PIO transfer when
previous one has not finished yet.

If previous PIO transfer is not finished yet, the kernel may issue a new
PIO request only if the previous PIO transfer timed out.

In the past the root cause of this issue was incorrectly identified (as it
often happens during link retraining or after link down event) and special
hack was implemented in Trusted Firmware to catch all SError events in EL3,
to ignore errors with code 0xbf000002 and not forwarding any other errors
to kernel and instead throw panic from EL3 Trusted Firmware handler.

Links to discussion and patches about this issue:
https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?id=3c7dcdac5c50
https://lore.kernel.org/linux-pci/20190316161243.29517-1-repk@triplefau.lt/
https://lore.kernel.org/linux-pci/971be151d24312cc533989a64bd454b4@www.loen.fr/
https://review.trustedfirmware.org/c/TF-A/trusted-firmware-a/+/1541

But the real cause was the fact that during link retraining or after link
down event the PIO transfer may take longer time, up to the 1.44s until it
times out. This increased probability that a new PIO transfer would be
issued by kernel while previous one has not finished yet.

After applying this change into the kernel, it is possible to revert the
mentioned TF-A hack and SError events do not have to be caught in TF-A EL3.

Link: https://lore.kernel.org/r/20210608203655.31228-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 7fbcb5da811b ("PCI: aardvark: Don't rely on jiffies while holding spinlock")

PCI: Add AMD RS690 quirk to enable 64-bit DMA

Although the AMD RS690 chipset has 64-bit DMA support, BIOS implementations
sometimes fail to configure the memory limit registers correctly.

The Acer F690GVM mainboard uses this chipset and a Marvell 88E8056 NIC. The
sky2 driver programs the NIC to use 64-bit DMA, which will not work:

  sky2 0000:02:00.0: error interrupt status=0x8
  sky2 0000:02:00.0 eth0: tx timeout
  sky2 0000:02:00.0 eth0: transmit ring 0 .. 22 report=0 done=0

Other drivers required by this mainboard either don't support 64-bit DMA,
or have it disabled using driver specific quirks. For example, the ahci
driver has quirks to enable or disable 64-bit DMA depending on the BIOS
version (see ahci_sb600_enable_64bit() in ahci.c). This ahci quirk matches
against the SB600 SATA controller, but the real issue is almost certainly
with the RS690 PCI host that it was commonly attached to.

To avoid this issue in all drivers with 64-bit DMA support, fix the
configuration of the PCI host. If the kernel is aware of physical memory
above 4GB, but the BIOS never configured the PCI host with this
information, update the registers with our values.

[bhelgaas: drop PCI_DEVICE_ID_ATI_RS690 definition]
Link: https://lore.kernel.org/r/20210611214823.4898-1-mikel@mikelr.com
Signed-off-by: Mikel Rychliski <mikel@mikelr.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

PCI: Add ACS quirk for Broadcom BCM57414 NIC

The Broadcom BCM57414 NIC may be a multi-function device. While it does
not advertise an ACS capability, peer-to-peer transactions are not possible
between the individual functions, so it is safe to treat them as fully
isolated.

Add an ACS quirk for this device so the functions can be in independent
IOMMU groups and attached individually to userspace applications using
VFIO.

[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1621645997-16251-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org

PCI: Mark AMD Navi14 GPU ATS as broken

Observed unexpected GPU hang during runpm stress test on 0x7341 rev 0x00.
Further debugging shows broken ATS is related.

Disable ATS on this part.  Similar issues on other devices:

  a2da5d8cc0b0 ("PCI: Mark AMD Raven iGPU ATS as broken in some platforms")
  45beb31d3afb ("PCI: Mark AMD Navi10 GPU rev 0x00 ATS as broken")
  5e89cd303e3a ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")

Suggested-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://lore.kernel.org/r/20210602021255.939090-1-evan.quan@amd.com
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org

PCI: Work around Huawei Intelligent NIC VF FLR erratum

pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum
time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the
FLR to complete.  It assumes the FLR is complete when a config read returns
valid data.

When we do an FLR on several Huawei Intelligent NIC VFs at the same time,
firmware on the NIC processes them serially.  The VF may respond to config
reads before the firmware has completed its reset processing.  If we bind a
driver to the VF (e.g., by assigning the VF to a virtual machine) in the
interval between the successful config read and completion of the firmware
reset processing, the NIC VF driver may fail to load.

Prevent this driver failure by waiting for the NIC firmware to complete its
reset processing.  Not all NIC firmware supports this feature.

[bhelgaas: commit log]
Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr
Link: https://lore.kernel.org/r/20210414132301.1793-1-chiqijun@huawei.com
Signed-off-by: Chiqijun <chiqijun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org

PCI: Mark some NVIDIA GPUs to avoid bus reset

Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the
device inoperable for the current system boot. It requires a system
hard-reboot to get the GPU device back to normal operating condition
post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the
issue.

This issue will be fixed in the next generation of hardware.

Link: https://lore.kernel.org/r/20210608054857.18963-8-ameynarkhede03@gmail.com
Signed-off-by: Shanker Donthineni <sdonthineni@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sinan Kaya <okaya@kernel.org>
Cc: stable@vger.kernel.org

PCI: Mark TI C667X to avoid bus reset

Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS
automatically disables LTSSM when Secondary Bus Reset is received and
device stops working. Prevent bus reset for these devices. With this
change, the device can be assigned to VMs with VFIO, but it will leak state
between VMs.

Reference: https://e2e.ti.com/support/processors/f/791/t/954382
Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com
Signed-off-by: Antti Järvinen <antti.jarvinen@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable@vger.kernel.org

PCI: tegra194: Fix MCFG quirk build regressions

7f100744749e ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
caused a few build regressions:

  - 7f100744749e removed the Makefile rule for CONFIG_PCIE_TEGRA194, so
    pcie-tegra.c can no longer be built as a module.  Restore that rule.

  - 7f100744749e added "#ifdef CONFIG_PCIE_TEGRA194" around the native
    driver, but that's only set when the driver is built-in (for a module,
    CONFIG_PCIE_TEGRA194_MODULE is defined).

    The ACPI quirk is completely independent of the rest of the native
    driver, so move the quirk to its own file and remove the #ifdef in the
    native driver.

  - 7f100744749e added symbols that are always defined but used only when
    CONFIG_PCIEASPM, which causes warnings when CONFIG_PCIEASPM is not set:

      drivers/pci/controller/dwc/pcie-tegra194.c:259:18: warning: ‘event_cntr_data_offset’ defined but not used [-Wunused-const-variable=]
      drivers/pci/controller/dwc/pcie-tegra194.c:250:18: warning: ‘event_cntr_ctrl_offset’ defined but not used [-Wunused-const-variable=]
      drivers/pci/controller/dwc/pcie-tegra194.c:243:27: warning: ‘pcie_gen_freq’ defined but not used [-Wunused-const-variable=]

Fixes: 7f100744749e ("PCI: tegra: Add Tegra194 MCFG quirks for ECAM errata")
Link: https://lore.kernel.org/r/20210610064134.336781-1-jonathanh@nvidia.com
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>

PCI: of: Clear 64-bit flag for non-prefetchable memory below 4GB

Alexandru and Qu reported this resource allocation failure on ROCKPro64 v2
and ROCK Pi 4B, both based on the RK3399:

  pci_bus 0000:00: root bus resource [mem 0xfa000000-0xfbdfffff 64bit]
  pci 0000:00:00.0: PCI bridge to [bus 01]
  pci 0000:00:00.0: BAR 14: no space for [mem size 0x00100000]
  pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00003fff 64bit]

"BAR 14" is the PCI bridge's 32-bit non-prefetchable window, and our PCI
allocation code isn't smart enough to allocate it in a host bridge window
marked as 64-bit, even though this should work fine.

A DT host bridge description includes the windows from the CPU address
space to the PCI bus space.  On a few architectures (microblaze, powerpc,
sparc), the DT may also describe PCI devices themselves, including their
BARs.

Before 9d57e61bf723 ("of/pci: Add IORESOURCE_MEM_64 to resource flags for
64-bit memory addresses"), of_bus_pci_get_flags() ignored the fact that
some DT addresses described 64-bit windows and BARs.  That was a problem
because the virtio virtual NIC has a 32-bit BAR and a 64-bit BAR, and the
driver couldn't distinguish them.

9d57e61bf723 set IORESOURCE_MEM_64 for those 64-bit DT ranges, which fixed
the virtio driver.  But it also set IORESOURCE_MEM_64 for host bridge
windows, which exposed the fact that the PCI allocator isn't smart enough
to put 32-bit resources in those 64-bit windows.

Clear IORESOURCE_MEM_64 from host bridge windows since we don't need that
information.

Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Fixes: 9d57e61bf723 ("of/pci: Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses")
Link: https://lore.kernel.org/r/20210614230457.752811-1-punitagrawal@gmail.com
Reported-at: https://lore.kernel.org/lkml/7a1e2ebc-f7d8-8431-d844-41a9c36a8911@arm.com/
Reported-at: https://lore.kernel.org/lkml/YMyTUv7Jsd89PGci@m4/T/#u
Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Reported-by: Qu Wenruo <wqu@suse.com>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Tested-by: Domenico Andreoli <domenico.andreoli@linux.com>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>

tracing: Do no increment trace_clock_global() by one

The trace_clock_global() tries to make sure the events between CPUs is
somewhat in order. A global value is used and updated by the latest read
of a clock. If one CPU is ahead by a little, and is read by another CPU, a
lock is taken, and if the timestamp of the other CPU is behind, it will
simply use the other CPUs timestamp.

The lock is also only taken with a "trylock" due to tracing, and strange
recursions can happen. The lock is not taken at all in NMI context.

In the case where the lock is not able to be taken, the non synced
timestamp is returned. But it will not be less than the saved global
timestamp.

The problem arises because when the time goes "backwards" the time
returned is the saved timestamp plus 1. If the lock is not taken, and the
plus one to the timestamp is returned, there's a small race that can cause
the time to go backwards!

CPU0 CPU1
---- ----
trace_clock_global() {
    ts = clock() [ 1000 ]
    trylock(clock_lock) [ success ]
    global_ts = ts; [ 1000 ]

    <interrupted by NMI>
trace_clock_global() {
    ts = clock() [ 999 ]
    if (ts < global_ts)
ts = global_ts + 1 [ 1001 ]

    trylock(clock_lock) [ fail ]

    return ts [ 1001]
}
    unlock(clock_lock);
    return ts; [ 1000 ]
}

trace_clock_global() {
    ts = clock() [ 1000 ]
    if (ts < global_ts) [ false 1000 == 1000 ]

    trylock(clock_lock) [ success ]
    global_ts = ts; [ 1000 ]
    unlock(clock_lock)

    return ts; [ 1000 ]
}

The above case shows to reads of trace_clock_global() on the same CPU, but
the second read returns one less than the first read. That is, time when
backwards, and this is not what is allowed by trace_clock_global().

This was triggered by heavy tracing and the ring buffer checker that tests
for the clock going backwards:

Ring buffer clock went backwards: 20613921464 -> 20613921463
------------[ cut here ]------------
WARNING: CPU: 2 PID: 0 at kernel/trace/ring_buffer.c:3412 check_buffer+0x1b9/0x1c0
Modules linked in:
[..]
[CPU: 2]TIME DOES NOT MATCH expected:20620711698 actual:20620711697 delta:6790234 before:20613921463 after:20613921463
   [20613915818] PAGE TIME STAMP
   [20613915818] delta:0
   [20613915819] delta:1
   [20613916035] delta:216
   [20613916465] delta:430
   [20613916575] delta:110
   [20613916749] delta:174
   [20613917248] delta:499
   [20613917333] delta:85
   [20613917775] delta:442
   [20613917921] delta:146
   [20613918321] delta:400
   [20613918568] delta:247
   [20613918768] delta:200
   [20613919306] delta:538
   [20613919353] delta:47
   [20613919980] delta:627
   [20613920296] delta:316
   [20613920571] delta:275
   [20613920862] delta:291
   [20613921152] delta:290
   [20613921464] delta:312
   [20613921464] delta:0 TIME EXTEND
   [20613921464] delta:0

This happened more than once, and always for an off by one result. It also
started happening after commit aafe104aa9096 was added.

Cc: stable@vger.kernel.org
Fixes: aafe104aa9096 ("tracing: Restructure trace_clock_global() to never block")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

tracing: Do not stop recording comms if the trace file is being read

A while ago, when the "trace" file was opened, tracing was stopped, and
code was added to stop recording the comms to saved_cmdlines, for mapping
of the pids to the task name.

Code has been added that only records the comm if a trace event occurred,
and there's no reason to not trace it if the trace file is opened.

Cc: stable@vger.kernel.org
Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

tracing: Do not stop recording cmdlines when tracing is off

The saved_cmdlines is used to map pids to the task name, such that the
output of the tracing does not just show pids, but also gives a human
readable name for the task.

If the name is not mapped, the output looks like this:

<...>-1316 [005] ...2 132.044039: ...

Instead of this:

gnome-shell-1316 [005] ...2 132.044039: ...

The names are updated when tracing is running, but are skipped if tracing
is stopped. Unfortunately, this stops the recording of the names if the
top level tracer is stopped, and not if there's other tracers active.

The recording of a name only happens when a new event is written into a
ring buffer, so there is no need to test if tracing is on or not. If
tracing is off, then no event is written and no need to test if tracing is
off or not.

Remove the check, as it hides the names of tasks for events in the
instance buffers.

Cc: stable@vger.kernel.org
Fixes: 7ffbd48d5cab2 ("tracing: Cache comms only after an event occurred")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

recordmcount: Correct st_shndx handling

One should only use st_shndx when >SHN_UNDEF and <SHN_LORESERVE. When
SHN_XINDEX, then use .symtab_shndx. Otherwise use 0.

This handles the case: st_shndx >= SHN_LORESERVE && st_shndx != SHN_XINDEX.

Link: https://lore.kernel.org/lkml/20210607023839.26387-1-mark-pk.tsai@mediatek.com/
Link: https://lkml.kernel.org/r/20210616154126.2794-1-mark-pk.tsai@mediatek.com
Reported-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Tested-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[handle endianness of sym->st_shndx]
Signed-off-by: Mark-PK Tsai <mark-pk.tsai@mediatek.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>

mac80211: handle various extensible elements correctly

Various elements are parsed with a requirement to have an
exact size, when really we should only check that they have
the minimum size that we need. Check only that and therefore
ignore any additional data that they might carry.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.cd101f8040a4.Iadf0e9b37b100c6c6e79c7b298cc657c2be9151a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: reset profile_periodicity/ema_ap

Apparently we never clear these values, so they'll remain set
since the setting of them is conditional. Clear the values in
the relevant other cases.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.316e32d136a9.I2a12e51814258e1e1b526103894f4b9f19a91c8d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: avoid double free of PMSR request

If cfg80211_pmsr_process_abort() moves all the PMSR requests that
need to be freed into a local list before aborting and freeing them.
As a result, it is possible that cfg80211_pmsr_complete() will run in
parallel and free the same PMSR request.

Fix it by freeing the request in cfg80211_pmsr_complete() only if it
is still in the original pmsr list.

Cc: stable@vger.kernel.org
Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.1fbef57e269a.I00294bebdb0680b892f8d1d5c871fd9dbe785a5e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

cfg80211: make certificate generation more robust

If all net/wireless/certs/*.hex files are deleted, the build
will hang at this point since the 'cat' command will have no
arguments. Do "echo | cat - ..." so that even if the "..."
part is empty, the whole thing won't hang.

Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.c989056c3664.Ic3b77531d00b30b26dcd69c64e55ae2f60c3f31e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

mac80211: minstrel_ht: fix sample time check

We need to skip sampling if the next sample time is after jiffies, not before.
This patch fixes an issue where in some cases only very little sampling (or none
at all) is performed, leading to really bad data rates

Fixes: 80d55154b2f8 ("mac80211: minstrel_ht: significantly redesign the rate probing strategy")
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210617103854.61875-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

powerpc/perf: Fix crash in perf_instruction_pointer() when ppmu is not set

On systems without any specific PMU driver support registered, running
perf record causes Oops.

The relevant portion from call trace:

  BUG: Kernel NULL pointer dereference on read at 0x00000040
  Faulting instruction address: 0xc0021f0c
  Oops: Kernel access of bad area, sig: 11 [#1]
  BE PAGE_SIZE=4K PREEMPT CMPCPRO
  SAF3000 DIE NOTIFICATION
  CPU: 0 PID: 442 Comm: null_syscall Not tainted 5.13.0-rc6-s3k-dev-01645-g7649ee3d2957 #5164
  NIP:  c0021f0c LR: c00e8ad8 CTR: c00d8a5c
  NIP perf_instruction_pointer+0x10/0x60
  LR  perf_prepare_sample+0x344/0x674
  Call Trace:
    perf_prepare_sample+0x7c/0x674 (unreliable)
    perf_event_output_forward+0x3c/0x94
    __perf_event_overflow+0x74/0x14c
    perf_swevent_hrtimer+0xf8/0x170
    __hrtimer_run_queues.constprop.0+0x160/0x318
    hrtimer_interrupt+0x148/0x3b0
    timer_interrupt+0xc4/0x22c
    Decrementer_virt+0xb8/0xbc

During perf record session, perf_instruction_pointer() is called to
capture the sample IP. This function in core-book3s accesses
ppmu->flags. If a platform specific PMU driver is not registered, ppmu
is set to NULL and accessing its members results in a crash. Fix this
crash by checking if ppmu is set.

Fixes: 2ca13a4cc56c ("powerpc/perf: Use regs->nip when SIAR is zero")
Cc: stable@vger.kernel.org # v5.11+
Reported-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Athira Rajeev <atrajeev@linux.vnet.ibm.com>
Tested-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/1623952506-1431-1-git-send-email-atrajeev@linux.vnet.ibm.com

Merge tag 'amd-drm-fixes-5.13-2021-06-16' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-5.13-2021-06-16:

amdgpu:
- GFX9 and 10 powergating fixes

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210616204913.4368-1-alexander.deucher@amd.com

Merge tag 'for-linus' of git://git./virt/kvm/kvm

Pull kvm fixes from Paolo Bonzini:
"Miscellaneous bugfixes.

  The main interesting one is a NULL pointer dereference reported by
  syzkaller ("KVM: x86: Immediately reset the MMU context when the SMM
  flag is cleared")"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: selftests: Fix kvm_check_cap() assertion
  KVM: x86/mmu: Calculate and check "full" mmu_role for nested MMU
  KVM: X86: Fix x86_emulator slab cache leak
  KVM: SVM: Call SEV Guest Decommission if ASID binding fails
  KVM: x86: Immediately reset the MMU context when the SMM flag is cleared
  KVM: x86: Fix fall-through warnings for Clang
  KVM: SVM: fix doc warnings
  KVM: selftests: Fix compiling errors when initializing the static structure
  kvm: LAPIC: Restore guard to prevent illegal APIC register access

net: qed: Fix memcpy() overflow of qed_dcbx_params()

The source (&dcbx_info->operational.params) and dest
(&p_hwfn->p_dcbx_info->set.config.params) are both struct qed_dcbx_params
(560 bytes), not struct qed_dcbx_admin_params (564 bytes), which is used
as the memcpy() size.

However it seems that struct qed_dcbx_operational_params
(dcbx_info->operational)'s layout matches struct qed_dcbx_admin_params
(p_hwfn->p_dcbx_info->set.config)'s 4 byte difference (3 padding, 1 byte
for "valid").

On the assumption that the size is wrong (rather than the source structure
type), adjust the memcpy() size argument to be 4 bytes smaller and add
a BUILD_BUG_ON() to validate any changes to the structure sizes.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: cdc_eem: fix tx fixup skb leak

when usbnet transmit a skb, eem fixup it in eem_tx_fixup(),
if skb_copy_expand() failed, it return NULL,
usbnet_start_xmit() will have no chance to free original skb.

fix it by free orginal skb in eem_tx_fixup() first,
then check skb clone status, if failed, return NULL to usbnet.

Fixes: 9f722c0978b0 ("usbnet: CDC EEM support (v5)")
Signed-off-by: Linyu Yuan <linyyuan@codeaurora.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mlx5-fixes-2021-06-16' of git://git./linux/kernel/git/saeed/linux

Saeed Mahameed says:

====================
mlx5 fixes 2021-06-16

This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: hamradio: fix memory leak in mkiss_close

My local syzbot instance hit memory leak in
mkiss_open()[1]. The problem was in missing
free_netdev() in mkiss_close().

In mkiss_open() netdevice is allocated and then
registered, but in mkiss_close() netdevice was
only unregistered, but not freed.

Fail log:

BUG: memory leak
unreferenced object 0xffff8880281ba000 (size 4096):
  comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s)
  hex dump (first 32 bytes):
    61 78 30 00 00 00 00 00 00 00 00 00 00 00 00 00  ax0.............
    00 27 fa 2a 80 88 ff ff 00 00 00 00 00 00 00 00  .'.*............
  backtrace:
    [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0
    [<ffffffff8706e7e8>] alloc_netdev_mqs+0x98/0xe80
    [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1]
    [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110
    [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670
    [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440
    [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200
    [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0
    [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae

BUG: memory leak
unreferenced object 0xffff8880141a9a00 (size 96):
  comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s)
  hex dump (first 32 bytes):
    e8 a2 1b 28 80 88 ff ff e8 a2 1b 28 80 88 ff ff  ...(.......(....
    98 92 9c aa b0 40 02 00 00 00 00 00 00 00 00 00  .....@..........
  backtrace:
    [<ffffffff8709f68b>] __hw_addr_create_ex+0x5b/0x310
    [<ffffffff8709fb38>] __hw_addr_add_ex+0x1f8/0x2b0
    [<ffffffff870a0c7b>] dev_addr_init+0x10b/0x1f0
    [<ffffffff8706e88b>] alloc_netdev_mqs+0x13b/0xe80
    [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1]
    [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110
    [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670
    [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440
    [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200
    [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0
    [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae

BUG: memory leak
unreferenced object 0xffff8880219bfc00 (size 512):
  comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s)
  hex dump (first 32 bytes):
    00 a0 1b 28 80 88 ff ff 80 8f b1 8d ff ff ff ff  ...(............
    80 8f b1 8d ff ff ff ff 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0
    [<ffffffff8706eec7>] alloc_netdev_mqs+0x777/0xe80
    [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1]
    [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110
    [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670
    [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440
    [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200
    [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0
    [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae

BUG: memory leak
unreferenced object 0xffff888029b2b200 (size 256):
  comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0
    [<ffffffff8706f062>] alloc_netdev_mqs+0x912/0xe80
    [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1]
    [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110
    [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670
    [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440
    [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200
    [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0
    [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae

Fixes: 815f62bf7427 ("[PATCH] SMP rewrite of mkiss")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Fix an error handling path in 'be_probe()'

If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it
must be undone by a corresponding 'pci_disable_pcie_error_reporting()'
call, as already done in the remove function.

Fixes: d6b6d9877878 ("be2net: use PCIe AER capability")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

KVM: selftests: Fix kvm_check_cap() assertion

KVM_CHECK_EXTENSION ioctl can return any negative value on error,
and not necessarily -1. Change the assertion to reflect that.

Signed-off-by: Fuad Tabba <tabba@google.com>
Message-Id: <20210615150443.1183365-1-tabba@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>