[media] xc4000: detect also xc4100

Added code to detect the XC4100 chip, which is presumably an analog-only
"value" version of the XC4000. It is not sure, however, if any devices
using this have actually been produced and sold, so the patch may be
unneeded.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: removed redundant tuner reset

This patch causes the tuner reset command to be ignored in the firmware
code, since this only happens when the BASE/INIT1 firmware is loaded by
check_firmware(), and in that case check_firmware() already calls the
reset callback before starting to load the firmware.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: xc_tune_channel() cleanup

Minor coding changes related to the xc_tune_channel() function.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: implemented analog TV and radio

The following patch implements support for analog TV and FM radio.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: added audio_std module parameter

The 'audio_std' module parameter makes it possible to fine tune
some audio related aspects of the driver, like setting the exact
audio standard (NICAM, A2, etc.) to be used for some video standards.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: setting registers

This patch implements setting the registers in xc4000_set_params()
and xc4000_set_analog_params(). A new register is defined which enables
filtering of the composite video output (this is needed to avoid bad
picture quality with some boards).

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: debug message improvements

The following patch makes a few minor changes to the printing
of debug messages, and reporting the tuner status. The 'debug'
module parameter can now be set from 0 to 2 to control the
verbosity of debug messages.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: firmware initialization

This patch fixes/cleans up the loading of the firmware file when the
driver is loaded and initialized.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: implemented power management

The following patch implements the xc4000_sleep() function.
The 'no_powerdown' module parameter is now interpreted differently:
  - 0 uses a device-specific default
  - 1 disables power management like before
  - 2 enables power management

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: added card_type

This patch adds support for selecting a card type in struct
xc4000_config, to allow for implementing some card specific code
in the driver.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: check_firmware() cleanup

This patch makes the following fixes in check_firmware():
  - there is only one BASE and INIT1 firmware for XC4000
  - loading SCODE is needed also for FM radio

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: simplified load_scode

Removed unused code from load_scode() (all SCODE firmwares are
assumed to have the HAS_IF bit set).

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: simplified seek_firmware()

This patch simplifies the code in seek_firmware().

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: added firmware_name parameter

The firmware_name module parameter makes it possible to set the firmware
file name. It defaults to "xc4000.fw" if not specified.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: fixed frequency error

The xc_get_frequency_error() function reported the frequency error
incorrectly. The data read from the hardware is a signed integer, in
15625 Hz units. The attached patch fixes the bug.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: added mutex

This patch adds a mutex to xc4000_priv, to protect the driver
from being accessed by multiple processes at the same time.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: added support for 7 MHz DVB-T

The following patch implements support for DVB-T with 7 MHz bandwidth.

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: updated standards table

This patch makes the following changes to the standards table:
  - added 'u16 int_freq' to struct XC_TV_STANDARD (needed for analog TV
    and radio, 0 for DVB-T)
  - added new standard for SECAM-D/K video with PAL-D/K audio
  - the 'int_freq' values are now specified in the table
  - changed VideoMode for NTSC and PAL-B/G standards

Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: code cleanup

This is the first of a set of patches that update the original xc4000
sources to my modified version. It removes some unused code, and makes
a few minor formatting changes.

[mchehab@redhat.com: re-add XC_TUNE_ANALOG/XC_TUNE_DIGITAL constants, to avoid compilation breakage]
Signed-off-by: Istvan Varga <istvan_v@mailbox.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: Fix a few bad whitespaces on it

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: remove notes from bringup of PCTV 340e

Remove some inline comments I had written from when I was computing the proper
dib7000p configuration to work with the xc4000.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: cleanup dmesg logging

Remove some printk() calls added during driver development, and demote some
other messages to debug only (to reduce dmesg chatter).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: rename firmware image filename

Give the xc4000 firmware filename a filename that makes more sense for public
release.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: turn off debug logging by default

Don't dump debug into to dmesg by default (something I had enabled during
bringup of the xc4000 driver).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: make PCTV 340e work!

Fixup the PLL and AGC configs so that the 340e works (correcting errors I made
when I did the original config blindly).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: get rid of hard-coded 8MHz firmware config

Remove a hack I had put in to force the firmware to be 8MHz, now setting
the firmware properly based on the target standard.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: fixup PLL config for PCTV 340e

Based on a reference trace under Windows, reverse engineer the PLL config.
Note that the xtal is not yet setup, and the timf cannot be determined yet
because my reference trace doesn't actually achieve a signal lock.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: handle dib0700 broken i2c stretching

It was confirmed by DibCom that i2c stretching is broken in the i2c master
on the dib7700.  So we need to put a hack into the xc4000 driver to not
complain in certain very specific cases where we know i2c stretching occurs.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: setup dib7000p AGC config for PCTV 340e

Setup a proper AGC config for the 340e, based on the Windows USB trace

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: use if_khz provided in xc4000_config

Remove hard-coded references to 5400, using the value passed in when the
xc4000 is attached.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: continued cleanup of the firmware loading routine

Properly setup the standard firmware loading and scode loading, as well as
getting rid of a ton of dead code.  Note that I am getting a single i2c
error when the standard firmware sets the video standard, but everything else
seems to be loading properly now.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: add code to do standard and scode firmware loading

Add code to handle firmware blobs for the standard and scode.  Note there
appears to be some issue with loading the DTV8 standard firmware, probably
related to direct/indirect mode.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: remove xc5000 firmware loading routine

Since we use the xc3028 version of the firmware file parsing routine (which
includes support for scodes and separate blobs), we can drop the xc5000
version of the code.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: remove XREG_BUSY code only supported in xc5000

The xc4000 driver is based on the original xc5000 driver, and while the
xc5000 supports the XREG_BUSY register, the xc4000 does not.  So remove the
code in question.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: properly set type for init1 firmware

We need to set the firmware type properly in order to locate the init1
firmware.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: cut over to using xc5000 version for loading i2c sequences

The xc3028 version does i2c splitting in a different manner than xc4000 and
xc5000, so reuse the xc5000 version of the routine (the key here being that
xc4000 expects the first *two* bytes to be the same for splitting transactions.

Doing it the xc3028 way was resulting in i2c errors partially through the
firmware load.  With this change, it would appear that the entire base firmware
is being loaded successfully (product id now properly shows 0x0FA0).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] xc4000: pull in firmware management code from xc3028

Switch over to using the firmware management routines from the tuner-xc2028,
since that has support for scodes, etc.

This code still requires signficant cleanup, and at this point the base
firmware does not load properly (i2c write errors about 300 bytes in).

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib7000p: setup dev.parent for i2c master built into 7000p

We need to set the dev.parent member on the dib7000p on its i2c master, or
else calls to request_firmware() will hit an oops in 2.6.31.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: add a sleep before attempting to detect dib7000p

Add a sleep since in some cases the dib7000p wasn't online when being probed.
The optimal timing has not yet been determined.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: successfully connect to xc4000 over i2c for PCTV 340e

Use the correct i2c bus to communicate with the tuner, and properly setup the
reset GPIO and i2c address.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: properly setup GPIOs for PCTV 340e

Provide a frontend setup routine for the PCTV 340e which takes into account
the specific GPIO setup of the board.

Note that this patch does *not* take into account the xc4000 reset pin, which
is attached to the dib7000.

Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: add USB id for PCTV 340eSE

Add the board profile for the PCTV 340eSE, since that's what I have here
for development.

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dib0700: add initial code for PCTV 340e by Davide Ferri

This is initial code written by Davide Ferri for the PCTV 340e, including
a new xc4000 driver.  I am checking in all the code unmodified, and making
no assertions about its quality (other than confirming it compiles).

[mchehab@redhat.com: rebased on the top of the current tree]
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Davide Ferri <davidef1986@gmail.com>
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v011: Fixed gain calculation

The implementation of the gain calculation for this sensor is incorrect.
It is only working for the first 127 values.

The reason is, that the gain cannot be set directly by writing a value
into the gain registers of the sensor. The gain register work this way
(see datasheet page 24): bits 0 to 6 are called "initial gain". These
are linear. But bits 7 and 8 ("analog multiplicative factors") and bits
9 and 10 ("digital multiplicative factors") work completely different:
Each of these bits increase the gain by the factor 2. So if the bits
7-10 are 0011, 0110, 1100 or 0101 for example, the gain from bits 0-6 is
multiplied by 4. The order of the bits 7-10 is not important for the
resulting gain. (But there are some recommended values for low noise)

The current driver doesn't do this correctly: If the current gain is 000
0111 1111 (127) and the gain is increased by 1, you would expect the
image to become brighter. But the image is completly dark, because the
new gain is 000 1000 0000 (128). This means: Initial gain of 0,
multiplied by 2. The result is 0.

This patch adds a new function which does the gain calculation and also
fixes the same bug for red_balance and blue_balance. Additionally, the
driver follows the recommendation from the datasheet, which says, that
the gain should always be above 0x0020.

Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v011: Added exposure for mt9v011

There are problems when you use this camera/sensor in a very bright room
or outside. The image is completely white, because it is overexposed.
The driver uses a default value which is not suitable for all
environments.

This patch makes it possible to adjust the exposure time by youself. I
found out by logging the i2c-data, that the windows driver for this
sensor is doing this, too. I tested the camera on a sunny day and after
adjusting the exposure time, I was able to see a very good image.

Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] mt9v011: Fixed incorrect value for the first valid column

According to the datasheet (page 8), the first optical clear
pixel-column is not at position 14. The correct/recommended value is 20.
Without this patch there is a dark line on the left side of the image.

Tested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Johannes Obermaier <johannes.obermaier@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc-core: fix winbond-cir issues

The conversion of winbond-cir to use rc-core seems to have missed a
a few bits and pieces which were in my local tree. Kudos to
Juan Jesús García de Soria Lucena <skandalfo@gmail.com> for noticing.

[mchehab@redhat.com: fix two UTF-8 violations]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc/redrat3: dereferencing null pointer

In the original code, if the allocation failed we dereference "rr3"
when it was NULL.

Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] rc: double unlock in rc_register_device()

If change_protocol() fails and we goto out_raw, then it calls unlock
twice.  I noticed that the other time we called change_protocol() we
held the &dev->lock, so I changed it to hold it here too.

Reviewed-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] DVB: dvb_frontend: fix dtv_property_dump for DTV_DVBT2_PLP_ID

- Add missing entry to array "dtv_cmds".
- Set array size to DTV_MAX_COMMAND + 1 to avoid future off-by-ones.

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] V4L/videobuf2-memops: use pr_debug for debug messages

Otherwise they clutter the dmesg buffer even on a production kernel.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] dvb-usb.h function rc5_scan

The function "rc5_scan" in "dvb_usb.h" is returning invalid value.
The value should be returned "u16" but is returning "u8".

See example below in "drivers/media/dvb/dvb-usb/opera1.c":

        send_key = (send_key & 0xffff) | 0x0100;

        for (i = 0; i < ARRAY_SIZE(rc_map_opera1_table); i++) {
            if (rc5_scan(&rc_map_opera1_table[i]) == (send_key & 0xffff)) {
                *state = REMOTE_KEY_PRESSED;
                *event = rc_map_opera1_table[i].keycode;
                opst->last_key_pressed =
                    rc_map_opera1_table[i].keycode;
                break;
            }
            opst->last_key_pressed = 0;
        }

Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-sf16fmr2: convert to generic TEA575x interface

Convert radio-sf16fmr2 to use generic TEA575x implementation. Most of the
driver code goes away as SF16-FMR2 is basically just a TEA5757 tuner
connected to ISA bus.
The card can optionally be equipped with PT2254A volume control (equivalent
of TC9154AP) - the volume setting is completely reworked (with balance control
added) and tested.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx24113: Don't reuse core macro names

The info and err macros are already defined by the USB stack. Rename
these macros to avoid macro redefinition warnings.

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] itd1000: Don't reuse core macro names

The dbg, warn and info macros are already defined by the USB stack.
Rename these macros to avoid macro redefinition warnings.

Refactor lineshift in printouts.

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] radio-si470x: fix memory leak in si470x_usb_driver_probe()

radio->int_in_urb is not deallocated on error paths in si470x_usb_driver_probe().

Found by Linux Driver Verification project (linuxtesting.org).

Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] media: Convert vmalloc/memset to vzalloc

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

dvb_net: Simplify the code if DVB NET is not defined

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Make DVB NET configurable in the kernel

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] tea575x: convert to control framework

Convert tea575x-tuner to use the new V4L2 control framework. Also add
ext_init() callback that can be used by a card driver for additional
initialization right before registering the video device (for SF16-FMR2).

Also embed struct video_device to struct snd_tea575x to simplify the code.

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Fix compile warning: Dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Hans Petter Selasky <hselasky@c2i.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] v4l: Document EACCES in VIDIOC_[GS]_CTRL and VIDIOC_{G, S, TRY}_EXT_CTRLS

VIDIOC_S_CTRL and VIDIOC_S_EXT_CTRLS return EACCES when setting a read-only
control VIDIOC_TRY_EXT_CTRLS when trying a read-only control and
VIDIOC_G_CTRL and VIDIOC_G_EXT_CTRLS when getting a write-only control.
Document this.

Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] videobuf_pages_to_sg: sglist[0] length problem

On function videobuf_pages_to_sg the statement sg_set_page(&sglist[0],
pages[0], PAGE_SIZE - offset, offset) will fail if size is less than
PAGE_SIZE.

Signed-off-by: Newson Edouard <newsondev@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cx23885: restore flushes of cx23885_dev work items

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] saa7164: poll mask set incorrectly

list_first_entry() always returns non-null here.  I think the intent was
to test whether there were any entries in the used list.

Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: Steven Toth <stoth@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: correct missing error checks

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] Update several cardlists

Several cardlist entries are missed. Fix them by running some
script magic (about the same scripts we used to have at -hg tree).

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: use the proper prefix for board names

All boards use EM28xxx_BOARD, to identify that the macro
refers to a card entry. So:

EM2874_LEADERSHIP_ISDBT -> EM2874_BOARD_LEADERSHIP_ISDBT

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: correct PCTV nanoStick T2 290e device name

PCTV Systems nanoStick T2 290e => PCTV nanoStick T2 290e

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: add remote for PCTV nanoStick T2 290e

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] em28xx: EM28174 remote support

For some reason it repeats rather slowly, around 800ms intervals,
two RC5 remotes tested.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: fix bitfields

error: dubious one-bit signed bitfield

Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] cxd2820r: malloc buffers instead of stack

kmalloc I2C buffers

Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: style issues, comments, etc

Change some info, comments, variables. No functionality changes.

Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: add support for Anysee E7 PS2

Basically it is just same device as Anysee E7 S2 but made for
internal PCI(e) slot and motherboard USB connector.

Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] anysee: add support for Anysee E7 PTC

Basically it is just same device as Anysee E7 TC but made for
internal PCI(e) slot and motherboard USB connector.

Cc: info@anysee.com
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] gspca - ov519: New sensor ov9600 with bridge ovfx2

This sensor was found in a webcam 8020:ef04 (SVC - SVU2-1.3MV PCCam).

Signed-off-by: Jean-François Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] DocBook: Move all media docbook stuff into its own directory

This patch addresses several issues pointed by Randy Dunlap
<rdunlap@xenotime.net> at changeset ece722c:

- In the generated index.html file, "media" is listed first, but it
  should be listed in alphabetical order, not first.

- The generated files are (hidden) in .tmpmedia/

- The link from the top-level index.html file to "media" is to
  media/index.html, but the file is actually in .tmpmedia/media/index.html

- Please build docs with and without using "O=builddir" and test that.

- Would it be possible for media to have its own Makefile instead of
  merging into this one?

Due to the way cleandocs target works, I had to rename the media DocBook
to media_api, otherwise cleandocs would remove the /media directory.

Thanks-to: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

[media] DocBook: Add rules to auto-generate some media docbook

Auto-generate the videodev2.h.xml,frontend.h.xml and the indexes.

Some logic at the Makefile helps us to identify when a symbol is missing,
like for example:

Error: no ID for constraint linkend: V4L2-PIX-FMT-JPGL.

Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Linux 3.0

Merge branch 'for_linus' of git://git./linux/kernel/git/jwessel/linux-2.6-kgdb

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  sparc,kgdbts: fix compile regression with kgdb test suite

sparc,kgdbts: fix compile regression with kgdb test suite

Commit 63ab25ebbc (kgdbts: unify/generalize gdb breakpoint adjustment)
introduced a compile regression on sparc.

kgdbts.c: In function 'check_and_rewind_pc':
kgdbts.c:307: error: implicit declaration of function 'instruction_pointer_set'

Simply add the correct macro definition for instruction pointer on the
Sparc architecture.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: David S. Miller <davem@davemloft.net>

Merge git://git./linux/kernel/git/sfrench/cifs-2.6

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  CIFS: Fix wrong length in cifs_iovec_read

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Make Dell Latitude E6420 use reboot=pci
  x86: Make Dell Latitude E5420 use reboot=pci

x86: Make Dell Latitude E6420 use reboot=pci

Yet another variant of the Dell Latitude series which requires
reboot=pci.

From the E5420 bug report by Daniel J Blueman:

> The E6420 is affected also (same platform, different casing and
> features), which provides an external confirmation of the issue; I can
> submit a patch for that later or include it if you prefer:
> http://linux.koolsolutions.com/2009/08/04/howto-fix-linux-hangfreeze-during-reboots-and-restarts/

Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

x86: Make Dell Latitude E5420 use reboot=pci

Rebooting on the Dell E5420 often hangs with the keyboard or ACPI
methods, but is reliable via the PCI method.

[ hpa: this was deferred because we believed for a long time that the
  recent reshuffling of the boot priorities in commit
  660e34cebf0a11d54f2d5dd8838607452355f321 fixed this platform.
  Unfortunately that turned out to be incorrect. ]

Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Link: http://lkml.kernel.org/r/1305248699-2347-1-git-send-email-daniel.blueman@gmail.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>

Merge branch 'drm-intel-fixes' of git://git./linux/kernel/git/keithp/linux-2.6

* 'drm-intel-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/keithp/linux-2.6:
  drm/i915: Fix unfenced alignment on pre-G33 hardware
  drm/i915: Add quirk to disable SSC on Lenovo U160 LVDS

vfs: drop conditional inode prefetch in __do_lookup_rcu

It seems to hurt performance in real life.  Yes, the inode will be used
later, but the conditional doesn't seem to predict all that well
(negative dentries are not uncommon) and it looks like the cost of
prefetching is simply higher than depending on the cache doing the right
thing.

As usual.

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

FS-Cache: Fix __fscache_uncache_all_inode_pages()'s outer loop

The compiler, at least for ix86 and m68k, validly warns that the
comparison:

next <= (loff_t)-1

is always true (and it's always true also for x86-64 and probably all
other arches - as long as pgoff_t isn't wider than loff_t).  The
intention appears to be to avoid wrapping of "next", so rather than
eliminating the pointless comparison, fix the loop to indeed get exited
when "next" would otherwise wrap.

On m68k the following warning is observed:

  fs/fscache/page.c: In function '__fscache_uncache_all_inode_pages':
  fs/fscache/page.c:979: warning: comparison is always false due to limited range of data type

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Suresh Jayaraman <sjayaraman@suse.de>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

CIFS: Fix wrong length in cifs_iovec_read

Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  signal: align __lock_task_sighand() irq disabling and RCU
  softirq,rcu: Inform RCU of irq_exit() activity
  sched: Add irq_{enter,exit}() to scheduler_ipi()
  rcu: protect __rcu_read_unlock() against scheduler-using irq handlers
  rcu: Streamline code produced by __rcu_read_unlock()
  rcu: Fix RCU_BOOST race handling current->rcu_read_unlock_special
  rcu: decrease rcu_report_exp_rnp coupling with scheduler

Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Avoid creating superfluous NUMA domains on non-NUMA systems
  sched: Allow for overlapping sched_domain spans
  sched: Break out cpu_power from the sched_group structure

Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86. reboot: Make Dell Latitude E6320 use reboot=pci
  x86, doc only: Correct real-mode kernel header offset for init_size
  x86: Disable AMD_NUMA for 32bit for now

Merge branch 'rcu/urgent' of git://git./linux/kernel/git/paulmck/linux-2.6-rcu into core/urgent

signal: align __lock_task_sighand() irq disabling and RCU

The __lock_task_sighand() function calls rcu_read_lock() with interrupts
and preemption enabled, but later calls rcu_read_unlock() with interrupts
disabled.  It is therefore possible that this RCU read-side critical
section will be preempted and later RCU priority boosted, which means that
rcu_read_unlock() will call rt_mutex_unlock() in order to deboost itself, but
with interrupts disabled. This results in lockdep splats, so this commit
nests the RCU read-side critical section within the interrupt-disabled
region of code.  This prevents the RCU read-side critical section from
being preempted, and thus prevents the attempt to deboost with interrupts
disabled.

It is quite possible that a better long-term fix is to make rt_mutex_unlock()
disable irqs when acquiring the rt_mutex structure's ->wait_lock.

Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>

softirq,rcu: Inform RCU of irq_exit() activity

The rcu_read_unlock_special() function relies on in_irq() to exclude
scheduler activity from interrupt level.  This fails because exit_irq()
can invoke the scheduler after clearing the preempt_count() bits that
in_irq() uses to determine that it is at interrupt level.  This situation
can result in failures as follows:

 $task IRQ SoftIRQ

 rcu_read_lock()

 /* do stuff */

 <preempt> |= UNLOCK_BLOCKED

 rcu_read_unlock()
   --t->rcu_read_lock_nesting

irq_enter();
/* do stuff, don't use RCU */
irq_exit();
  sub_preempt_count(IRQ_EXIT_OFFSET);
  invoke_softirq()

ttwu();
  spin_lock_irq(&pi->lock)
  rcu_read_lock();
  /* do stuff */
  rcu_read_unlock();
    rcu_read_unlock_special()
      rcu_report_exp_rnp()
        ttwu()
          spin_lock_irq(&pi->lock) /* deadlock */

   rcu_read_unlock_special(t);

Ed can simply trigger this 'easy' because invoke_softirq() immediately
does a ttwu() of ksoftirqd/# instead of doing the in-place softirq stuff
first, but even without that the above happens.

Cure this by also excluding softirqs from the
rcu_read_unlock_special() handler and ensuring the force_irqthreads
ksoftirqd/# wakeup is done from full softirq context.

[ Alternatively, delaying the ->rcu_read_lock_nesting decrement
  until after the special handling would make the thing more robust
  in the face of interrupts as well.  And there is a separate patch
  for that. ]

Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-and-tested-by: Ed Tomlinson <edt@aei.ca>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>

sched: Add irq_{enter,exit}() to scheduler_ipi()

Ensure scheduler_ipi() calls irq_{enter,exit} when it does some actual
work. Traditionally we never did any actual work from the resched IPI
and all magic happened in the return from interrupt path.

Now that we do do some work, we need to ensure irq_{enter,exit} are
called so that we don't confuse things.

This affects things like timekeeping, NO_HZ and RCU, basically
everything with a hook in irq_enter/exit.

Explicit examples of things going wrong are:

  sched_clock_cpu() -- has a callback when leaving NO_HZ state to take
                    a new reading from GTOD and TSC. Without this
                    callback, time is stuck in the past.

  RCU -- needs in_irq() to work in order to avoid some nasty deadlocks

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>

rcu: protect __rcu_read_unlock() against scheduler-using irq handlers

The addition of RCU read-side critical sections within runqueue and
priority-inheritance lock critical sections introduced some deadlock
cycles, for example, involving interrupts from __rcu_read_unlock()
where the interrupt handlers call wake_up().  This situation can cause
the instance of __rcu_read_unlock() invoked from interrupt to do some
of the processing that would otherwise have been carried out by the
task-level instance of __rcu_read_unlock().  When the interrupt-level
instance of __rcu_read_unlock() is called with a scheduler lock held
from interrupt-entry/exit situations where in_irq() returns false,
deadlock can result.

This commit resolves these deadlocks by using negative values of
the per-task ->rcu_read_lock_nesting counter to indicate that an
instance of __rcu_read_unlock() is in flight, which in turn prevents
instances from interrupt handlers from doing any special processing.
This patch is inspired by Steven Rostedt's earlier patch that similarly
made __rcu_read_unlock() guard against interrupt-mediated recursion
(see https://lkml.org/lkml/2011/7/15/326), but this commit refines
Steven's approach to avoid the need for preemption disabling on the
__rcu_read_unlock() fastpath and to also avoid the need for manipulating
a separate per-CPU variable.

This patch avoids need for preempt_disable() by instead using negative
values of the per-task ->rcu_read_lock_nesting counter.  Note that nested
rcu_read_lock()/rcu_read_unlock() pairs are still permitted, but they will
never see ->rcu_read_lock_nesting go to zero, and will therefore never
invoke rcu_read_unlock_special(), thus preventing them from seeing the
RCU_READ_UNLOCK_BLOCKED bit should it be set in ->rcu_read_unlock_special.
This patch also adds a check for ->rcu_read_unlock_special being negative
in rcu_check_callbacks(), thus preventing the RCU_READ_UNLOCK_NEED_QS
bit from being set should a scheduling-clock interrupt occur while
__rcu_read_unlock() is exiting from an outermost RCU read-side critical
section.

Of course, __rcu_read_unlock() can be preempted during the time that
->rcu_read_lock_nesting is negative.  This could result in the setting
of the RCU_READ_UNLOCK_BLOCKED bit after __rcu_read_unlock() checks it,
and would also result it this task being queued on the corresponding
rcu_node structure's blkd_tasks list.  Therefore, some later RCU read-side
critical section would enter rcu_read_unlock_special() to clean up --
which could result in deadlock if that critical section happened to be in
the scheduler where the runqueue or priority-inheritance locks were held.

This situation is dealt with by making rcu_preempt_note_context_switch()
check for negative ->rcu_read_lock_nesting, thus refraining from
queuing the task (and from setting RCU_READ_UNLOCK_BLOCKED) if we are
already exiting from the outermost RCU read-side critical section (in
other words, we really are no longer actually in that RCU read-side
critical section).  In addition, rcu_preempt_note_context_switch()
invokes rcu_read_unlock_special() to carry out the cleanup in this case,
which clears out the ->rcu_read_unlock_special bits and dequeues the task
(if necessary), in turn avoiding needless delay of the current RCU grace
period and needless RCU priority boosting.

It is still illegal to call rcu_read_unlock() while holding a scheduler
lock if the prior RCU read-side critical section has ever had either
preemption or irqs enabled.  However, the common use case is legal,
namely where then entire RCU read-side critical section executes with
irqs disabled, for example, when the scheduler lock is held across the
entire lifetime of the RCU read-side critical section.

Signed-off-by: Paul E. McKenney <paul.mckenney@linaro.org>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>

sched: Avoid creating superfluous NUMA domains on non-NUMA systems

When creating sched_domains, stop when we've covered the entire
target span instead of continuing to create domains, only to
later find they're redundant and throw them away again.

This avoids single node systems from touching funny NUMA
sched_domain creation code and reduces the risks of the new
SD_OVERLAP code.

Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Anton Blanchard <anton@samba.org>
Cc: mahesh@linux.vnet.ibm.com
Cc: benh@kernel.crashing.org
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/1311180177.29152.57.camel@twins
Signed-off-by: Ingo Molnar <mingo@elte.hu>

sched: Allow for overlapping sched_domain spans

Allow for sched_domain spans that overlap by giving such domains their
own sched_group list instead of sharing the sched_groups amongst
each-other.

This is needed for machines with more than 16 nodes, because
sched_domain_node_span() will generate a node mask from the
16 nearest nodes without regard if these masks have any overlap.

Currently sched_domains have a sched_group that maps to their child
sched_domain span, and since there is no overlap we share the
sched_group between the sched_domains of the various CPUs. If however
there is overlap, we would need to link the sched_group list in
different ways for each cpu, and hence sharing isn't possible.

In order to solve this, allocate private sched_groups for each CPU's
sched_domain but have the sched_groups share a sched_group_power
structure such that we can uniquely track the power.

Reported-and-tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/n/tip-08bxqw9wis3qti9u5inifh3y@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>