review.tizen.org Git - platform/kernel/linux-rpi.git/log

wifi: mac80211: stop warning after reconfig failures

If we have a reconfig failure in the driver, then we need
to shut down the network interface(s) at the network stack
level through cfg80211, which can result in a lot of those
"Failed check-sdata-in-driver check, ..." warnings, since
interfaces are considered to not be in the driver when the
reconfiguration fails, but we still need to go through all
the shutdown flow.

Avoid many of these warnings by storing the fact that the
stack experienced a reconfiguration failure and not doing
the warning in that case.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.3750c4ae6e76.I9e80d6026f59263c008a1a68f6cd6891ca0b93b0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211_hwsim: Fix possible NULL dereference

In a call to mac80211_hwsim_select_tx_link() the sta pointer might
be NULL, thus need to check that it is not NULL before accessing it.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.f4d889fc98c4.Iae85f527ed245a37637a874bb8b8c83d79812512@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: consistently use u64 for BSS changes

Currently, enum ieee80211_bss_change has more than 32 flags.
Change the type of the corresponding variables from u32 to u64.

Signed-off-by: Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.10354a05eaf1.If19359262fe2728dd523ea6d7c3aa7dc50940411@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: batch recalc during STA flush

When we flush stations, we first take them off the list
and then destroy them one by one. If we do the different
mode recalculations while destroying them, we cause the
following scenario:
- STA 1 has 80 MHz - min chanctx width is now 80 MHz
- STA 2 has 80 MHz
- empty STA list
- destroy STA 2
- recalc min chanctx width -> results in 20 MHz as
the STA list is already empty

This is broken, since as far as the driver is concerned
STA 1 still exists at this point, and this causes issues
at least with iwlwifi.

Fix - and also optimize - this by doing the recalc of
min chanctx width (and also P2P PS) only after all the
stations were removed.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.48d262b6b42d.Ia15532657c17535c28ec0c5df263b65f0f80663c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: move sta_info_move_state() up

To fix a sequencing issue, this code needs to be changed
a bit. Move it up in the file to prepare for that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.05bb735d7075.I984b5c194a0f84580247d73620a4e61a5f82a774@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: recalc min chandef for new STA links

When adding a new link to a station, this needs to cause a
recalculation of the minimum chandef since otherwise we can
have a higher bandwidth station connected on that link than
the link is operating at. Do the appropriate recalc.

Fixes: cb71f1d136a6 ("wifi: mac80211: add sta link addition/removal")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.377adf3c789a.I91bf28f399e16e6ac1f83bacd1029a698b4e6685@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211_hwsim: check the return value of nla_put_u32

Check the return value of nla_put_u32() and handle it accordingly.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.de5168568cf6.Ie16442af9be879fd835506ba5dade780edecfb60@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: provide a helper to fetch the medium synchronization delay

There are drivers which need this information.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.b1043f3126e2.Iad3806f8bf8df07f52ef0a02cc3d0373c44a8c93@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: refactor ieee80211_select_link_key()

Simplify ieee80211_select_link_key(), no functional changes are made.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.a4e332755bb0.Iff4a2b6ed767b2a329c51c29bb597ece9ebe2af8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: use u64 to hold enum ieee80211_bss_change flags

The size of enum ieee80211_bss_change is bigger that 32,
so we need u64 to be used in a flag. Also pass u64
instead of u32 to ieee80211_reconfig_ap_links() for the same
reason.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230604120651.d53b7018a4eb.I1adaa041de51d50d84a11226573e81ceac0fe90d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: implement proper AP MLD HW restart

Previously, I didn't implement restarting here at all if the
interface is an MLD, so it only worked for non-MLO. Add the
needed code to restart an AP MLD correctly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-12-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: fetch and store the EML capability information

We need to teach the low level driver about the EML capability which
includes information for EMLSR / EMLMR operation.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-11-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: skip EHT BSS membership selector

Skip the EHT BSS membership selector for getting rates.
While at it, add the definitions for GLK and EPS, and
sort the list.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-9-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211_hwsim: avoid warning with MLO PS stations

If the station disables all links it's in powersave and
we shouldn't transmit anything to it, but we don't handle
that correctly yet. For now, just avoid the warning, once
we really add support for this case we can revert to the
old warning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-8-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: remove element scratch_len

This isn't used, and there isn't really a good way it
could be used, so just remove that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: mac80211: HW restart for MLO

Implement proper reconfiguration for interfaces that are
doing MLO, in order to be able to recover from HW restart
correctly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230504134511.828474-6-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: pnvm: handle memory descriptor tlv

When PNVM is obtained from UEFI, there's an additional memory
descriptor TLV that has to be handled. It is the same TLV that
holds data in the reduced power tables. Also, in this TLV, the
actual data is located after address and size, so add the
corresponding offset.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.8c5f5ee8e30b.Id1893c9dec140b5ba4abe8a121c2e1a1d121d2d7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: fw: don't use constant size with efi.get_variable

Use efi.get_variable() with NULL pointer for data in order to
obtain entry size and then call it again with the correct size
to get the entry itself.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.ef95a8055a50.Iae5389baaf0a9a3c89469f7502275ee119d378b6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: fw: clean up PNVM loading code

This code is a bit of a maze of gotos etc. Clean up the
code a bit to make the intent clearer.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.51fb5ee63f21.I20f270b2d47612e84643dc235c2940b8d9ed9930@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Separate reading and parsing of reduce power table

It enables to better handle error cases. Also save the image till the
end of the loading and only then free it.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.71e3b3e0e794.Ifbe69ad99a7e805eb70e09280365821eb146b1c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Enable loading of reduce-power tables into several segments

Replace the field reduce_power_dram with a struct that holds data about
the reduced-power tables drams regions. Generalize load_payloads_segments()
to work for both pnvm tables and reduction power tables.
Make required adjustments in the data structures.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.6fe66958f049.I85d80682229fc02fe354462cc9da40937558f30c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Use iwl_pnvm_image in reduce power tables flow

Generalize the parsing, loading, and setting of the power-reduce
tables, in order to support allocation of several DRAM payloads
in the future.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.564f1eead99b.Iaba653b21dc09aafc72b9bbb3928abddce0db50a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Separate loading and setting of power reduce tables

Take the part that copies the tables into DRAM, out of the method
that sets the prph_scratch to make the code cleaner. Each of the
operations will get more complex in the future when it will also
support larger power-reduce tables images.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.7695684dc848.I13626cd318e5d68efec9618b2045f52788bff114@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Implement loading and setting of fragmented pnvm image

Save the pnvm payloads in several DRAM segments (not only in one as
used to). In addition, allocate a FW structure in DRAM that holds the
segments' addresses and forward its address to the FW. It's done when
FW has the capability to handle pnvm images this way (helps to process
large pnvm images).

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.dbdad8995ce1.I986213527982637042532de3851a1bd8a11be87a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Add support for fragmented pnvm images

Add support for fragmented pnvm images, depending on the FW capability.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.c49bfaf435a9.I0278312e7c3355b224cd870d4f8cf6578d12f03e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Allow trans_pcie track more than 1 pnvm DRAM region

Change the field pnvm_dram to an array that describes many regions
and add a counter to the number of pnvm regions that were allocated
in DRAM.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.bb206d71bf45.I627640701757bb2f234f8e18a3afbd6af1206658@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Take loading and setting of pnvm image out of parsing part

Change iwl_pnvm_parse so it will only save the information into the
iwl_pnvm_image struct. This enables to use the parsing code for the
power reduce tables in the future.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.504b42fc1611.I4ddf6ad76d922d118fcbcc4f0e9ec003753d0b75@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Separate loading and setting of pnvm image into two functions

Take the part that is copying the pnvm image into DRAM, out of the
the method that sets the prph_scratch. Makes the code cleaner since
those 2 operations don't always happen together (loading should happen
only once while setting can happen more than once).
In addition, each operation will get more complex in the future when
it will support also larger pnvm images.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.4c0728239fd6.Ibc30a9fbdb6123dadbe2dbb89318dbd5ec01080a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Generalize the parsing of the pnvm image

Generalize iwl_pnvm_parse(). This saves us from copying each payload
twice (first in the parsing and later when copying it to the dram).
Moreover, its more compatible for handling larger pnvm tables in
the future (in which payloads won't be concatenated).

The main changes are:

1. Take out the concatenating of the payloads from the parsing level
2. Start using iwl_pnvm_image structure that will hold pointers to
payloads that should be delivered to fw, their sizes and number.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230606103519.06c02f380b6f.I03a3030fca194aa0c4bc2ecd18531f8914e98cfd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: api: fix kernel-doc links

Some of the kernel-doc links are outdated due to other
changes, fix that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.85e2cf489893.Ie3889ea6f755b80c988543ccca56c67420c51b1f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: api: remove unused commands

Some commands are no longer used and have broken kernel-doc links,
so just remove them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.3dad4ad9b53e.I018abd02d6925950b8748dfb7a59db87255fc670@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: api: use __le16 instead of u16

Even for reserved values we shouldn't use u16, that's just
error prone. Fix this to __le16.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.29ebf70aa64e.I1263f6724e1c70ff5541f447b9744f143ee736a3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: api: link context action in kernel-doc

This is clearer in kernel-doc than spelling out the prefix.
It also lets us generate better tracing data.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601171633.e11ece794f60.I9874c7b0437071a2620d68ca5a16efed60da07a9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: tell firmware about per-STA MFP enablement

Indicate to the firmware for each station whether or not MFP
is used with this station. Note that we indicate MFP for it
before authorized since we don't know yet, and that will make
the firmware not handle should-be-protected management frames
without being able to check them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601095201.b1052f39af4c.I1b46b751d5808e65ea3d0e7b8b38209c5aecf042@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: send time sync only if needed

If there's no peer configured then there's no point in sending
the command down to the firmware with an invalid peer address.

Fixes: cf85123a210f ("wifi: iwlwifi: mvm: support enabling and disabling HW timestamping")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.0fb9f81f1852.Idcc41b67d1fbb421e5ed9bac2177b948b7b4d1c9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: remove warning for beacon filtering error

This warning is sometimes happening if we force a FW error
while disconnecting, which is annoying but harmless.

However, it's also pointless to throw a warning here, since
the stack and driver state doesn't really help, so just
remove that so the driver will ignore the error if any.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.29fe6990d372.I00ff5dc7bfb4025a609f380a0a3911d842b72449@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: remove dead code in iwl_dump_ini_imr_get_size()

Remove the check for the IMR debug data size which
leads to dead code.

Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.58eec8d40729.Ifb7d64706eed45726db804f36e785283dff7adab@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Add Dell to ppag approved list

Add 2 new entries for Dell in PPAG approved list.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194630.a2696f0538ef.I324e4a0cc4696c27830a490b79c42dfeff8ba074@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: FTM initiator MLO support

When checking if the initiator is associated to the responder,
iterate over all active links.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.a0d86655e7d2.I8f140ca55094da1d73c387fc036394fb2c148c85@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: pcie: adjust Bz device timings

The 100ms shouldn't be needed, only 10ms. However after
reset we should have 10ms as well for these devices.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.9a5627c1ff18.Ifcfbccd5458bd9ebd496aa834284fb0facfcaaef@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: offload BTM response during D3

There are mainly two types of BTM (BSS Transition Management)
requests, recommendations and notifications. For the first type,
a response is needed otherwise, most probably the STA will be
disconnected.
Since we don't want to wake up the host on it, set the BTM to reject
offload flag (if the device supports it) and rely on the FW to take
care of it. The FW will reject the BTM request and in case the AP
sends DEAUTH the FW can wake up the host to let it decide on the
next steps.

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.d95ae6f2804c.I9457acc55bc23ce715c714b5088058f52540c224@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: do not log undefined DRAM buffers unnecessarily

DRAM buffers that are not defined in the TLVs (or are unused in the
preset) would cause a log message. To avoid confusion, skip processing
buffers with an invalid (i.e. uninitialized) DRAM path.

This further reduces the noise of the message in cases where it is
unlikely to be helpful. Also update a related debug log string to better
describe what is happening.

Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.ecae60cf2d7f.Ib44a94d4aeb55dbb2e52edea8b69a09bc0f722c3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: acpi: add other Google OEMs to the ppag approved list

Add two new vendors to the PPAG approved vendor list
as Google OEMs.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.b89a3f9e3ae0.Iab1e13285c58ef1fee2a8bad8429eda4547b0b74@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: clarify EHT RU allocation bits

Calling this IWL_RX_PHY_DATA1_EHT_B0 is just confusing,
it's the RU allocation bit 0. Also then align the name
for B1-B7 accordingly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.824edb28c0eb.Ia9f74573e3ac771911b679558984f1bfb36de674@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: support injection rate control

Supporting controlling the frame rate during injection,
HT/VHT are supported in addition to legacy rates.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.85a662792649.I0847b47dec0dfb0290d7b15ebc6bc0a575eed7b5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: Add vendors to TAS approved list

Allows vendors to use the time average sar feature.

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531194629.845c205e4def.Iab5c849617ed7e13304e4dfc7def668659439946@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: iwlmei: fix compilation error

The feature is still disabled (depends on BROKEN), but
the code had a compilation error after one of the merges.
Fix that.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230531085033.216028-1-gregory.greenman@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: update response for mcc_update command

Add support for the MCC update response version 8.
Versions 5-6 are already covered by the existing
flags conversion, and 7 isn't used.

The capabilities field in iwl_mcc_update_resp is 32 bits
wide now, and the flags moved, so some more changes are
needed.

While at it, convert the flags to bool (to avoid having
to deal with BIT(16) specially etc.) and use the
struct_size() macro for the memory allocation.

Signed-off-by: Abhishek Naik <abhishek.naik@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.fd9016f8f994.Ibddcb9fbfa74895f742c0ac20968720691c94853@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: support PPAG in China for older FW cmd version

Allows the China bit in the ppag flags to turn on also when
FW cmd version is 1 (if FW has the capability).

Signed-off-by: Alon Giladi <alon.giladi@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.3cc19e799eeb.I9054b1d63fd7ae2b5f0e416825b4b1dc9f79cc80@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: remove useless code

Setting the station to -EBUSY was originally done under
this lock, and the comment still refers to it. But this
no longer happens because that was removed when DQA was
removed. Remove the leftover code as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.30048b1cd0fd.Ie2c2ff6fd7c6e3ebf5b736de350dc15515970792@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: disable RX STBC when a device doesn't support it

Some devices, like step A0 of GL FM device doesn't support RX STBC
for VHT/HE. Add a workaround to remove it from capabilities in
this case.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.65c3e09813e5.Iadfd8cdb0ea5a8088ae3daa555c780c423951894@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: fw: Add new ODM vendor to ppag approved list

Add new oem/odm pair to ppag approved vendors list
when specified by platform.

Signed-off-by: Ariel Malamud <ariel.malamud@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.549a57a1cf11.I7392b1cd31f4f7ee60aafe2093f4e82b1d6fd3a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: adjust csa notifications and commands to MLO

In the following notifications and commands mac_id was replaced
with link_id:
* CANCEL_CHANNEL_SWITCH_CMD
* CHANNEL_SWITCH_START_NOTIF
* CHANNEL_SWITCH_ERROR_NOTIF

The logic around was not changed, so only adjust handling
mac/link id.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.6aa6e394f5fe.Ie9e78918511ca901f9f3966d774fa74a71a186e3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: update the FW apis for LINK and MAC commands

The firmware added new fields to be able to pass the link_id as the AP
knows it and the esr_transition_timeout.
For now, pass only the link_id since we don't have access to the
esr_transition_timeout yet.

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.bf80ce717458.Icd4174911227c00cd12783fe1f517ae8097809b9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: Make iwl_mvm_diversity_iter() MLO aware

This function is MLO related, so it should iterate over all the links,
and not only on deflink.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.56a9c709e987.I9716195ec288cce2c929338c254ee9add8cfcc1f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: don't silently ignore missing suspend or resume ops

In case the driver doesn't implement suspend or resume operations
on the transport layer, notify the driver's upper layer.
Otherwise, we might access d3_status uninitialized.

Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.0c55e0ca92f1.I6870fe1683215e65d3d036f9b576b03b7b7257be@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: support PASN for MLO

When adding a PASN station, the non MLD API was used. This results
in assert when operating as MLD. Fix it to use the MLD API when
operating as MLD. For now, the default link is used for the added
station.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.7c35dccc8a12.I7bc78cd16d7c750f42fdd60e07e839a860d279d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: dissolve iwl_mvm_mac_add_interface_common()

This wasn't really common anymore, so dissolve it, it has a
pretty strange calling convention that's confusing.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.44320ab2e842.Ie1d6b9c28caca3b541ca383a4c0c8799b0e72fe0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: make internal callback structs const

There's no need for these to be writable, so they can
be const (and static).

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.c41eb6687868.I2dac1158e5723187bda1973aa49fde8a794621c8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: mvm: use link ID in missed beacon notification

This new version of missed beacon notification uses link_id
instead of mac_id. Also add an option to use link id for
retrieving vif.

Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.17fe1cc632f1.Id1fabb532e2174712fe17d4ad86a2c8c64ae84da@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: iwlwifi: cfg: freeze 22500 devices FW API

FW version is now frozen for 22500 devices. Don't
allow newer versions in the driver.

Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.8a25ebf9134c.I3f1454498322ce28cb687d28c091c7ee092cefca@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

wifi: brcmutil: use helper function pktq_empty() instead of open code

pktq_empty was added in commit 5b435de0d786 ("net: wireless: add brcm80211
drivers") but it is currently not being utilized in some areas. This commit
replaces the open code with the pktq_empty() function.

Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527114954.3281-2-claudiajkang@gmail.com

wifi: rtlwifi: use helper function rtl_get_hdr()

Although rtl_get_hdr was added in commit 3dad618b7b92 ("rtlwifi: Change
wifi.h for rtl8192se and rtl8192de"), it is currently not being utilized
in some areas. This commit replaces the open code with the rtl_get_hdr()
function.

Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527114954.3281-1-claudiajkang@gmail.com

wifi: rtw88: usb: silence log flooding error message

When receiving more rx packets than the kernel can handle the driver
drops the packets and issues an error message. This is bad for two
reasons. The logs are flooded with myriads of messages, but then time
consumed for printing messages in that critical code path brings down
the device. After some time of excessive rx load the driver responds
with:

rtw_8822cu 1-1:1.2: failed to get tx report from firmware
rtw_8822cu 1-1:1.2: firmware failed to report density after scan
rtw_8822cu 1-1:1.2: firmware failed to report density after scan

The device stops working until being replugged.

Fix this by lowering the priority to debug level and also by
ratelimiting it.

Fixes: a82dfd33d1237 ("wifi: rtw88: Add common USB chip support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230524103934.1019096-1-s.hauer@pengutronix.de

wifi: ray_cs: add sanity check on local->sram/rmem/amem

The ray_config uses ray_release as its unified error handling function.
However, it does not know if local->sram/rmem/amem succeeds or not.

Fix this by adding sanity check on local->sram/rmem/amem in the
ray_relase.

Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316133236.556198-3-dzm91@hust.edu.cn

wifi: ray_cs: remove one redundant del_timer

In ray_detach, it and its child function ray_release both call
del_timer(_sync) on the same timer.

Fix this by removing the del_timer_sync in the ray_detach, and revising
the del_timer to del_timer_sync.

Signed-off-by: Dongliang Mu <dzm91@hust.edu.cn>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230316133236.556198-2-dzm91@hust.edu.cn

wifi: ray_cs: Fix an error handling path in ray_probe()

Should ray_config() fail, some resources need to be released as already
done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
ray_probe(), not ray_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/8c544d18084f8b37dd108e844f7e79e85ff708ff.1684570373.git.christophe.jaillet@wanadoo.fr

wifi: wl3501_cs: Fix an error handling path in wl3501_probe()

Should wl3501_config() fail, some resources need to be released as already
done in the remove function.

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/7cc9c9316489b7d69b36aeb0edd3123538500b41.1684569865.git.christophe.jaillet@wanadoo.fr

wifi: atmel: Fix an error handling path in atmel_probe()

Should atmel_config() fail, some resources need to be released as already
done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
atmel_probe(), not atmel_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1e65f174607a83348034197fa7d603bab10ba4a9.1684569156.git.christophe.jaillet@wanadoo.fr

wifi: orinoco: Fix an error handling path in orinoco_cs_probe()

Should orinoco_cs_config() fail, some resources need to be released as
already done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
orinoco_cs_probe(), not orinoco_cs_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e24735ce4d82901d5f7ea08419eea53bfdde3d65.1684568286.git.christophe.jaillet@wanadoo.fr

wifi: orinoco: Fix an error handling path in spectrum_cs_probe()

Should spectrum_cs_config() fail, some resources need to be released as
already done in the remove function.

While at it, remove a useless and erroneous comment. The probe is
spectrum_cs_probe(), not spectrum_cs_attach().

Fixes: 15b99ac17295 ("[PATCH] pcmcia: add return value to _config() functions")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/c0bc0c21c58ca477fc5521607615bafbf2aef8eb.1684567733.git.christophe.jaillet@wanadoo.fr

wifi: rtw89: use flexible array member in rtw89_btc_btf_tlv

struct rtw89_btc_btf_tlv contains a one-byte member that is intended as a
flexible array:

In function 'fortify_memcpy_chk',
    inlined from '_append_tdma' at drivers/net/wireless/realtek/rtw89/coex.c:1579:3:
include/linux/fortify-string.h:583:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
  583 |                         __write_overflow_field(p_size_field, size);
      |                         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Make this actually use a flexible array to let the compiler understand.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230523113241.2772811-1-arnd@kernel.org

wifi: rtw89: 8851b: rfk: Fix spelling mistake KIP_RESOTRE -> KIP_RESTORE

There is a spelling mistake in a literal string. Fix it.

Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522085924.913649-1-colin.i.king@gmail.com

wifi: rtw89: use struct to access register-based H2C/C2H

The register-based H2C/C2H are used to exchange commands and events with
firmware. The exchange data is limited, but it is relatively simple,
because it can work before HCI initialization. To make these code clean,
use struct to access them. This patch doesn't change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-6-pkshih@realtek.com

wifi: rtw89: use struct and le32_get_bits() to access RX descriptor

RX descriptor is to provide basic and important information related to
packets, such as packet size, security, MAC ID and so on. Change to use
struct to access these fields, and not change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-5-pkshih@realtek.com

wifi: rtw89: use struct and le32_get_bits() to access received PHY status IEs

PHY status IEs generated by BB hardware is to provide more detail
information related to received packets, such as RSSI and bandwidth.

To avoid type casting, change buf type from u8* to void* as well.

This patch doesn't change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-4-pkshih@realtek.com

wifi: rtw89: use struct and le32_get_bits to access RX info

If received packet type is PPDU status, RX info provides information
attached by MAC hardware, and mention how long BB information attached.

This conversion patch doesn't change logic at all.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-3-pkshih@realtek.com

wifi: rtw89: add chip_ops::query_rxdesc() and rxd_len as helpers to support newer chips

The next generation chips use different RX descriptor format, so add
a chip_ops to hook suitable handlers. Also, the length of RX descriptor is
different, so add a variable to store the length according to chip and
descriptor content dynamically. Then, the code can be more general.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522122513.13559-2-pkshih@realtek.com

wifi: rtw89: 8851b: add 8851be to Makefile and Kconfig

Since 8851BE is ready, so add 8851BE to Makefile and Kconfig. Currently,
it can support STA, AP and monitor modes with good performance.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-8-pkshih@realtek.com

wifi: rtw89: add tx_wake notify for 8851B

8851B has the same issue: management frames get stuck when WiFi
chip enters low PS mode, so we also add notify wake function to
trigger WiFi chip wake before forwarding management frames.

Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-7-pkshih@realtek.com

wifi: rtw89: enlarge supported length of read_reg debugfs entry

The register ranges of upcoming chips are different from current, and even
existing chips have different ranges, so support longer length to dump
registers. Then, user space can decide the ranges according to chip.

Since arbitrary length (e.g. 7) would be a little complicated, so simply
make length a multiple of 16. The output looks like

18620000h : 8580801f 82828282 82828282 080800fd

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-6-pkshih@realtek.com

wifi: rtw89: 8851b: add RF configurations

RF configurations include RF calibrations and getting thermal value.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-5-pkshih@realtek.com

wifi: rtw89: 8851b: add MAC configurations to chip_info

These configurations include path control, TX grant, TX scheduler,
register-based H2C/C2H and so on.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-4-pkshih@realtek.com

wifi: rtw89: 8851b: fill BB related capabilities to chip_info

These capabilities include helpers of BT coexistence, RX PPDU status
parser, DIG (dynamic initial gain) and CFO (center frequency offset)
settings.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-3-pkshih@realtek.com

wifi: rtw89: 8851b: add TX power related functions

Get TX power value from tables according to selected country and channel,
and set proper power to registers.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230519031500.21087-2-pkshih@realtek.com

wifi: rtw89: refine packet offload handling under SER

H2C of packet offload needs to wait FW ACK by C2H. But, it's possible
that packet offload happens during SER (system error recovery), e.g.
SER L2 which restarts HW. More, packet offload flow isn't deferrable.
So, the H2C wait may get `ret == 1` (unreachable).

However, the logic FW deals with packet offload is simple enough, just
clone content. It means that as long as the H2C is issued successfully,
the thing will succeed sooner or later. Therefore, after we add a debug
log when receiving ACK to packet offload, it would be acceptable that
during SER, packet offload don't really wait for ACK. And, if debugging,
we can still check its debug logs. Besides, we can expect that if we see
SER before receiving ACK to packet offload, those debug logs of the ACK
have a time difference.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-4-pkshih@realtek.com

wifi: rtw89: tweak H2C TX waiting function for SER

Some specific H2C (host to chip command) needs waiting until FW ACK by
C2H (chip to host event). However, during SER (system error recovery),
most interrupts are disabled, so we can't receive C2H immediately. It
causes this kind of H2C TX waits will always time out during SER.

To save time spent by SER, we don't do these redundant waits. And, to
make a difference from -ETIMEDOUT in other cases, we make the function
return 1 for SER case. When some H2C callers really catch `ret == 1` at
runtime, they can determine whether it's reasonable or not, and consider
how to resolve their flow if needed.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-3-pkshih@realtek.com

wifi: rtw89: ser: reset total_sta_assoc and tdls_peer when L2

The total_sta_assoc and the tdls_peer are used for statistics accodring
to stations' information. L2 (Level 2) SER (system error recovery) will
call ieee80211_restart_hw() which re-invokes sta_state ops. And then,
the total_sta_assoc and tdls_peer will be re-increased. In case wrong
statistics results, we reset them in SER L2 handling.

Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230516082441.11154-2-pkshih@realtek.com

wifi: rtw88: Add support for the SDIO based RTL8723DS chipset

Wire up RTL8723DS chipset support using the rtw88 SDIO HCI code as well
as the existing RTL8723D chipset code.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-5-martin.blumenstingl@googlemail.com

mmc: sdio: Add/rename SDIO ID of the RTL8723DS SDIO wifi cards

RTL8723DS comes in two variant and each of them has their own SDIO ID:
- 0xd723 can connect two antennas. The WiFi part is still 1x1 so the
second antenna can be dedicated to Bluetooth
- 0xd724 can only connect one antenna so it's shared between WiFi and
Bluetooth

Add a new entry for the single antenna RTL8723DS (0xd724) which can be
found on the MangoPi MQ-Quad. Also rename the existing RTL8723DS entry
(0xd723) so it's name reflects that it's the variant with support for
two antennas.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-4-martin.blumenstingl@googlemail.com

wifi: rtw88: rtw8723d: Implement RTL8723DS (SDIO) efuse parsing

The efuse of the SDIO RTL8723DS chip has only one known member: the mac
address is at offset 0x11a. Add a struct rtw8723ds_efuse describing this
and use it for copying the mac address when the SDIO bus is used.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-3-martin.blumenstingl@googlemail.com

wifi: rtw88: sdio: Check the HISR RX_REQUEST bit in rtw_sdio_rx_isr()

rtw_sdio_rx_isr() is responsible for receiving data from the wifi chip
and is called from the SDIO interrupt handler when the interrupt status
register (HISR) has the RX_REQUEST bit set. After the first batch of
data has been processed by the driver the wifi chip may have more data
ready to be read, which is managed by a loop in rtw_sdio_rx_isr().

It turns out that there are cases where the RX buffer length (from the
REG_SDIO_RX0_REQ_LEN register) does not match the data we receive. The
following two cases were observed with a RTL8723DS card:
- RX length is smaller than the total packet length including overhead
  and actual data bytes (whose length is part of the buffer we read from
  the wifi chip and is stored in rtw_rx_pkt_stat.pkt_len). This can
  result in errors like:
    skbuff: skb_over_panic: text:ffff8000011924ac len:3341 put:3341
  (one case observed was: RX buffer length = 1536 bytes but
   rtw_rx_pkt_stat.pkt_len = 1546 bytes, this is not valid as it means
   we need to read beyond the end of the buffer)
- RX length looks valid but rtw_rx_pkt_stat.pkt_len is zero

Check if the RX_REQUEST is set in the HISR register for each iteration
inside rtw_sdio_rx_isr(). This mimics what the RTL8723DS vendor driver
does and makes the driver only read more data if the RX_REQUEST bit is
set (which seems to be a way for the card's hardware or firmware to
tell the host that data is ready to be processed).

For RTW_WCPU_11AC chips this check is not needed. The RTL8822BS vendor
driver for example states that this check is unnecessary (but still uses
it) and the RTL8822CS drops this check entirely.

Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522202425.1827005-2-martin.blumenstingl@googlemail.com

wifi: add HAS_IOPORT dependencies

In a future patch HAS_IOPORT=n will result in inb()/outb() and friends
not being declared. We thus need to add HAS_IOPORT as dependency for
those drivers using them.

Co-developed-by: Arnd Bergmann <arnd@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@kernel.org>
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230522105049.1467313-44-schnelle@linux.ibm.com

Merge ath-next from git://git./linux/kernel/git/kvalo/ath.git

ath.git patches for v6.5. Major changes:

ath11k

* Multiple Basic Service Set Identifier (MBSSID) and Enhanced MBSSID
Advertisement (EMA) support in AP mode

wifi: ath11k: Send HT fixed rate in WMI peer fixed param

Due to the firmware behavior with HT fixed rate setting,
HT fixed rate MCS with NSS > 1 are treated as NSS = 1
HT rates in the firmware and enables the HT fixed rate of
NSS = 1.

This leads to HT fixed rate is always configured for NSS = 1
even though the user sets NSS = 2 or > 1 HT fixed MCS in the
set bitrate command.

Currently HT fixed MCS is sent via WMI peer assoc command.
Fix this issue, by sending the HT fixed rate MCS in WMI peer
fixed param instead of sending in peer assoc command.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1

Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230504092033.3542456-3-quic_mkenna@quicinc.com

wifi: ath11k: Relocate the func ath11k_mac_bitrate_mask_num_ht_rates() and change hweight16 to hweight8

Relocate the function ath11k_mac_bitrate_mask_num_ht_rates() definition
to call this function from other functions which helps to avoid the
compilation error (function not defined).

ht_mcs[] is 1 byte array and it is enough to use hweight8() instead
of hweight16(). Hence, fixed the same.

Tested on: Compile tested only.

Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230504092033.3542456-2-quic_mkenna@quicinc.com

wifi: ath12k: increase vdev setup timeout

When vdev start/stop happens, response from firmware is received with delay
and hence there is a timeout before VDEV can be up/down.
Also, with maximum peers connected and when vdev stop occurs, firmware
will take time to clean up all the peers and vap queues.
In such cases as well, vdev start/stop response is sent by firmware with delay.

Increase the vdev setup timeout as recommended by firmware team.

Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1

Signed-off-by: Aishwarya R <quic_aisr@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230428091041.20033-1-quic_rgnanase@quicinc.com

wifi: rtw89: 8851b: rfk: add TSSI

TSSI is transmitter signal strength indication, which is a close-loop
hardware circuit to feedback actual transmitting power as a reference for
next transmission.

When we setup channel to connect an AP, it does full calibration. When
switching bands or channels, it needs to reset hardware status to prevent
use wrong feedback of previous transmission.

To do TX power compensation reflecting current temperature, it loads tables
of compensation values into registers according to channel and band group.

Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230513054425.9689-4-pkshih@realtek.com