Pali Rohár [Tue, 5 Apr 2022 09:15:21 +0000 (11:15 +0200)]
powerpc: dts: p2020: Add localbus node
This node is required for NAND and NOR support. Node is taken from the
upstream Linux kernel DTS file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 4 Apr 2022 16:33:11 +0000 (18:33 +0200)]
mmc: fsl_esdhc_spl: pre-PBL: implement redundancy support
QorIQ pre-PBL BootROM scans first 24 SD card sectors (each with fixed 512
bytes length) for boot signature. Implement same redundancy behavior in
fsl_esdhc_spl driver to allow loading proper U-Boot when boot sector is not
the first one.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 4 Apr 2022 16:32:13 +0000 (18:32 +0200)]
mmc: fsl_esdhc: Define macro ESDHCCTL_SNOOP for Snoop attribute
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 4 Apr 2022 16:17:21 +0000 (18:17 +0200)]
mtd: nand: raw: Add support for DT property nand-ecc-algo=bch
According to Linux kernel DT schema nand-controller.yaml, using DT property
nand-ecc-algo=bch is the correct way for specifying BCH as ECC algorithm.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 4 Apr 2022 16:17:20 +0000 (18:17 +0200)]
mtd: rawnand: fsl_elbc: Use ECC configuration from device tree
Initialize ECC configuration after nand_scan_ident() call and only in case
nand_scan_ident() have not done it. nand_scan_ident() fills ECC
configuration from device tree.
Fixes usage of NAND_ECC_SOFT_BCH when it is specified in device tree.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 4 Apr 2022 16:17:19 +0000 (18:17 +0200)]
mtd: rawnand: fsl_elbc: Add device tree support
This allows boards to specify NAND settings via standard DT properties.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 4 Apr 2022 16:17:18 +0000 (18:17 +0200)]
mtd: rawnand: fsl_elbc: Implement RNDOUT command
This is needed for SW ECC.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:42:26 +0000 (00:42 +0200)]
powerpc: dts: p2020: Add serial0 and serial1 via pq3-duart-0.dtsi
Import pq3-duart-0.dtsi device tree include file from upstream Linux kernel
for P2020. This allows U-Boot to use P2020 device tree files from upstream
Linux kernel which reference serial0 or serial1 devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:42:25 +0000 (00:42 +0200)]
powerpc: dts: p2020: Add fsl/p2020si-pre.dtsi and fsl/p2020si-post.dtsi symlinks
P2020 DTS files in upstream Linux kernel use fsl/p2020si-pre.dtsi and
fsl/p2020si-post.dtsi include device tree files.
Add symlinks for these include device tree files into U-Boot powerpc
directory and points them to U-Boot inline device tree files p2020.dtsi and
p2020-post.dtsi.
This allows to use P2020 DTS files from upstream Linux kernel in U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:24:27 +0000 (00:24 +0200)]
board: freescale: p1_p2_rdb_pc: Allow to compile it without env support
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:24:26 +0000 (00:24 +0200)]
ddr: fsl: Allow to compile it without env support
When env support is disabled then usage of env_get_f() generates linker
errors. So do not compile env_get_f() when env support is disabled (for
example when disabled only in SPL).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:24:25 +0000 (00:24 +0200)]
hwconfig: Allow to compile it without env support
When env support is disabled then usage of env_get() generates linker
errors. So do not compile env_get() when env support is disabled (for
example when disabled only in SPL).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:20:10 +0000 (00:20 +0200)]
mmc: mmc_mode_name() is used also when LOGLEVEL >= LOGL_DEBUG
When CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher then linker throws
error about undefined symbol mmc_mode_name(). So compile mmc_mode_name()
also when CONFIG_LOGLEVEL is set to LOGL_DEBUG or higher.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:17:01 +0000 (00:17 +0200)]
mmc: fsl_esdhc_spl: Call mmc_init() before booting from SD card
If env is stored on SD card then U-Boot SPL automatically calls mmc_init()
before it is going to load proper U-Boot from SD card.
If env is not stored on SD card then U-Boot SPL fails to read proper U-Boot
from SD card due to missing mmc_init() call.
So add missing mmc_init() call into fsl_esdhc_spl's mmc_boot() function.
It fixes booting from SD card on P2020 boards without env support in SPL.
mmc_init() returns early if card was already initialized, so there is no
issue with calling this function more times.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:17:00 +0000 (00:17 +0200)]
mmc: fsl_esdhc_spl: pre-PBL: fix determining U-Boot size
In pre-PBL header is stored size of code which BootROM copies from SD card
to L2/SRAM. This size has upper limit of L2 cache size. In most cases this
is size of U-Boot SPL or size of L2 cache.
Therefore this size in pre-PBL header cannot be used for determining size
of proper U-Boot.
So always use CONFIG_SYS_MMC_U_BOOT_SIZE for determining size of proper
U-Boot which stored on SD card.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:16:59 +0000 (00:16 +0200)]
mmc: fsl_esdhc_spl: pre-PBL: check for BOOT signature instead of MBR/DBR
Pre-PBL BootROMs (MPC8536E, MPC8569E, P2020, P1011, P1012, P1013, P1020,
P1021, P1022) require custom BOOT signature on sector 0 and MBR/DBR
signature is not required at all.
So add check for BOOT signature and remove check for MBR/DBR.
This allows U-Boot SPL to load proper U-Boot on pre-PBL BootROMs platforms
also from SD cards which do not have MBR/DBR signature on sector 0.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:05:10 +0000 (00:05 +0200)]
powerpc: mpc85xx: Show e500 core version
Distinguish between e500v1 and e500v2.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Sat, 2 Apr 2022 22:05:09 +0000 (00:05 +0200)]
powerpc: mpc85xx: Rename _start_e500 symbol to _start
The real entry point is _start_e500. There is no _start symbol at all. So
rename _start_e500 to _start for convension that _start symbol is used as
entry point.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Pali Rohár [Mon, 25 Apr 2022 03:59:08 +0000 (09:29 +0530)]
powerpc: mpc85xx: Drop _start symbol
_start symbol contains only 32-bit data number 0x27051956 despite it is
marked as text section. This magic number is IH_MAGIC which is used for
marking uboot image header.
mpc85xx start.S code does not define valid uboot image header, so IH_MAGIC
number in _start symbol is useless there.
Moreover this _start symbol is not used at all. Entry point is at symbol
_start_e500.
So because this _start symbol is not used for anything, completely remove
it with IH_MAGIC number. After _start symbol was _start_cont symbol, so
replace all relative address calculations by _start_cont.
Signed-off-by: Pali Rohár <pali@kernel.org>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Stephen Carlson [Tue, 29 Mar 2022 21:51:10 +0000 (14:51 -0700)]
armv8/fsl-lsch3: Suppress spurious warning on Layerscape CPUs
NXP/Freescale Layerscape CPUs support high-speed serial interfaces (SERDES)
that can be configured for the application. Interfaces not used by the
application can be set to protocol 0 to turn them off and save power, but
U-Boot would emit a warning that 0 was invalid for a SERDES protocol on
boot. Replace the warning text with a notice that the SERDES is disabled.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yuantian Tang [Wed, 9 Mar 2022 07:37:22 +0000 (15:37 +0800)]
armv8: layerscape: fix the function mismatch issue
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 25 Apr 2022 03:55:08 +0000 (09:25 +0530)]
board: sl28: add basic PSCI implementation
For now, this only provides reset and poweroff functions.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 28 Feb 2022 12:48:40 +0000 (13:48 +0100)]
armv8: psci: add ARMV8_PSCI_RELOCATE Kconfig option
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 28 Feb 2022 12:48:39 +0000 (13:48 +0100)]
armv8: psci: skip setup code if we are not EL3
If we are running in EL2 skip PSCI implementation setup. This avoids an
exception if CONFIG_ARMV8_PSCI is set, but u-boot is started by TF-A.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Fri, 22 Apr 2022 09:23:27 +0000 (14:53 +0530)]
armv8: layerscape: get rid of smc_call()
There are two different implementations to do a secure monitor call:
smc_call() and arm_smccc_smc(). The former is defined in fwcall.c and
seems to be an ad-hoc implementation. The latter is imported from linux.
smc_call() is also only available if CONFIG_ARMV8_PSCI is not defined.
This makes it impossible to have both PSCI calls and PSCI implementation
in one u-boot build. The layerscape SoC code decide at runtime via
check_psci() if there is a PSCI support. Therefore, this is a
prerequisite patch to add PSCI implementation support for the layerscape
SoCs.
Note, for the TFA part, this is only compile time tested with
(ls1028ardb_tfa_defconfig).
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Mon, 28 Feb 2022 12:48:37 +0000 (13:48 +0100)]
armv8: include psci_update_dt() unconditionally
psci_update_dt() is also required if CONFIG_ARMV8_PSCI is set, that is,
if u-boot is the PSCI provider.
Guard the check which is intended to call into the PSCI implementation
in the secure firmware, by the proper macro SEC_FIRMWARE_ARMV8_PSCI.
Mark the function as weak because - unfortunately - there is already
a stub of the same function in arch/arm/mach-rmobile/psci-r8a779a0.c
which does not the same as the common one.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Sean Anderson [Fri, 22 Apr 2022 08:31:36 +0000 (14:01 +0530)]
arm: layerscape: Disable erratum A009007 on LS1021A, LS1043A, and LS1046A
This erratum is reported to cause problems on these processors [1-3].
The problem is usually with the clocking, which is supposed to be
configured by the RCW [4]. However, if it is not set, or if the default
clocking is not correct, then this erratum will cause an SError.
However, according to Ran Wang in [1]:
" ... this erratum is used to pass USB compliance test only, you could
disable this workaround on your board if you don't any USB issue on
normal use case, I think it's fine."
So just disable this erratum by default for these processors.
[1] https://lore.kernel.org/all/
761ddd61-05c1-d9b8-ac90-
b8f425afde6c@denx.de/
[2] https://community.nxp.com/t5/Layerscape/LS1046A-U-BOOT-HALT-AT-ERRATUM-
A0090078/m-p/742993
[3] https://community.nxp.com/t5/QorIQ/Why-does-the-LS1043A-U-Boot-hang-at-code-that-fixes-erratum/m-p/644412
[4] https://source.codeaurora.org/external/qoriq/qoriq-components/rcw/tree/ls1046ardb/usb_phy_freq.rcw
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Sean Anderson [Tue, 22 Feb 2022 18:38:39 +0000 (13:38 -0500)]
armv8: fsl-layerscape: Respect Kconfig for erratum A009007
There is a Kconfig for this erratum, but it is ignored for armv8.
Respect it.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Fri, 22 Apr 2022 08:20:06 +0000 (13:50 +0530)]
configs: Layerscape: Remove the 'fdt_addr' env
On Layerscape platforms, the DTB is loaded from boot filesystem,
per the fdt_addr description in doc/README.distro, it must be
removed.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Tom Rini [Sat, 23 Apr 2022 12:06:28 +0000 (08:06 -0400)]
Merge branch '2022-04-22-assorted-updates'
- Add "-q" to fdt addr and use it in distro_bootcmd to make the user
experience less scary reading in normal try/fail cases.
- Let the adc update an environment variable like many other commands do
- Fix TPL SEPARATE_BSS check when locating DTB
- Allow ":" in PXE file names again
- Two Apple M1 fixes
Mark Kettenis [Tue, 19 Apr 2022 19:20:31 +0000 (21:20 +0200)]
arm: apple: Point stdout-path to framebuffer when keyboard present
Unless you have a spare Apple Silicon machine, getting access to
the serial port on Apple Silicon machines requires special
hardware. Given that most machines come with a built-in screen
the framebuffer is likely to be the most convenient output device
for most users. While U-Boot will output to both serial and
framebuffer, OSes might not. Therefore set stdout-path to point
at /chosen/framebuffer when a keyboard is connected to the machine.
This behaviour can be overridden by setting the "stdout" variable
in the U-Boot environment. I addition to that keep the serial
console as the default when running under the m1n1 hypervisor.
The m1n1 hypervisor virtualizes the serial port such that it
can be easily accessed from any other machine with a USB port.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Janne Grunau <j@jannau.net>
Tested-by: Janne Grunau <j@jannau.net>
Mark Kettenis [Tue, 19 Apr 2022 19:10:29 +0000 (21:10 +0200)]
arm: apple: Don't clear framebuffer
Enable CONFIG_NO_FB_CLEAR to preserve the Asahi logo. Since that
logo is drawn on a black background also enable
CONFIG_SYS_WHITE_ON_BLACK such that text printed by U-Boot is still
visible.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Lyle Franklin [Sat, 16 Apr 2022 15:36:43 +0000 (11:36 -0400)]
Allow colon in PXE bootfile URLs
- U-boot's PXE flow supports prefixing your bootfile name with an
IP address to fetch from a server other than the DHCP server,
e.g. `hostIPaddr:bootfilename`:
https://github.com/u-boot/u-boot/commit/
a93907c43f847f076dd0e34ee3b69b5e8e6d0d29
- However, this breaks bootfile paths which contain a colon, e.g.
`f0:ad:4e:10:1b:87/7/pxelinux.cfg/default`
- This patch checks whether the `hostIPaddr` prefix is a valid
IP address before overriding the serverIP otherwise the whole
bootfile path is preserved
Signed-off-by: Lyle Franklin <lylejfranklin@gmail.com>
Peter Hoyes [Thu, 31 Mar 2022 10:53:22 +0000 (11:53 +0100)]
fdt: Add -q option to fdt addr for distro_bootcmd
distro_bootcmd uses this construct a few times to test $fdt_addr_r,
and fall back on $fdtcontroladdr if not set/invalid:
if fdt addr ${fdt_addr_r}; then
...
else
...
fi
If the `fdt addr` test fails, it prints the following message on the
console, suggesting there is an error when there is not:
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
To remove this potentially confusing error message, this patch adds -q
as a 'quiet' option for fdt addr, and uses this flag in
config_distro_bootcmd.h
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Marek Vasut [Thu, 14 Apr 2022 16:52:25 +0000 (18:52 +0200)]
cmd: adc: Add support for storing ADC result in env variable
Add the ability to save ADC conversion result in an environment
variable. This is useful for further arbitrary processing by the
U-Boot scripts.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Andrew Abbott [Sat, 16 Apr 2022 00:12:31 +0000 (10:12 +1000)]
fdt: Fix TPL SEPARATE_BSS check when locating DTB
Commit
690af71850149bf242502f688eca80fb302d1f76 changed this condition
from an explicit
IS_ENABLED(CONFIG_SPL_SEPARATE_BSS)
to
CONFIG_IS_ENABLED(SEPARATE_BSS)
The documentation for CONFIG_IS_ENABLED() in include/linux/kconfig.h
implies that we will get the correct behaviour, but the actual behaviour
differs such that this condition is now always false.
This stopped TPL being able to load the device tree blob at least on the
ROCKPro64 board (RK3399 SoC), since the wrong device tree location was
chosen.
The issues causing this behaviour with CONFIG_IS_ENABLED() are:
1. The documentation implies that CONFIG_SPL_BUILD =>
CONFIG_SPL_<option> is considered before the TPL equivalent.
Actually, the TPL options have higher priority - see definition of
_CONFIG_PREFIX.
2. The documentation implies a fallthrough, eg. if CONFIG_SPL_BUILD is
defined but the CONFIG_SPL_<option> is not, then it will proceed to
check if CONFIG_TPL_BUILD
Actually, if CONFIG_TPL_BUILD is defined, then it stops there
and CONFIG_SPL_BUILD is not considered - see definition of
_CONFIG_PREFIX.
During TPL build, at least for the ROCKPro64, both CONFIG_TPL_BUILD
and CONFIG_SPL_BUILD are defined, but because of the above, only TPL
options are considered. Since there is no CONFIG_TPL_SEPARATE_BSS,
this fails.
Fixes:
690af71850 ("fdt: Correct condition for SEPARATE_BSS")
Signed-off-by: Andrew Abbott <andrew@mirx.dev>
Tom Rini [Fri, 22 Apr 2022 15:06:38 +0000 (11:06 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-pmic
Tom Rini [Fri, 22 Apr 2022 15:06:31 +0000 (11:06 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-usb
Tom Rini [Fri, 22 Apr 2022 14:17:35 +0000 (10:17 -0400)]
configs: Resync with savedefconfig
Resync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Sean Anderson [Wed, 23 Mar 2022 18:26:09 +0000 (14:26 -0400)]
power-domain: Fix use of uninitialized value in dev_power_domain_ctrl
If dev_count_phandle_with_args returns 0 or another error, then pd will never
have been initialized by power_domain_get_by_index. Avoid comparing against
pd.dev in this situation.
Fixes:
3e4fcfa4bc ("power-domain: fix hang in endless loop on i.MX8")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Fri, 22 Apr 2022 12:12:53 +0000 (08:12 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-watchdog
- device-tree-bindings: watchdog: document common properties (Philippe)
- nuvoton: Add support for Nuvoton (Jim)
Tom Rini [Fri, 22 Apr 2022 12:12:20 +0000 (08:12 -0400)]
Merge tag 'u-boot-imx-
20220422' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-
20220422
-------------------
- Switch to DM_SERIAL
- Drop MMCROOT
- several cleanup
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
Oleksii Titov [Wed, 20 Apr 2022 08:23:25 +0000 (11:23 +0300)]
Add support for TP-Link UE200 dongle
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Oleksii Titov <ootitov@gmail.com>
Michal Simek [Wed, 9 Mar 2022 09:05:45 +0000 (10:05 +0100)]
usb: dwc3: Add support for usb3-phy PHY configuration
When usb3-phy label is found, PHY driver is called and serdes line is
initialized. This is preparation for serdes/psgtr driver to configure GT
lines based on description in DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Michal Simek [Wed, 9 Mar 2022 09:05:44 +0000 (10:05 +0100)]
generic-phy: s/CONFIG_PHY/CONFIG_IS_ENABLED(PHY)/
Allow to disable PHY driver in SPL because it checks the CONFIG_SPL_PHY
variable for SPL builds.
The same change was done for usb by commit
fd09c205fc57 ("usb:
s/CONFIG_DM_USB/CONFIG_IS_ENABLED(DM_USB)/").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adam Ford [Fri, 4 Mar 2022 22:59:02 +0000 (16:59 -0600)]
usb: gadget: ci: Make various ops const
ci_udc_ops and ci_ep_ops do not change their operations.
Mark them as const.
Signed-off-by: Adam Ford <aford173@gmail.com>
Jim Liu [Fri, 1 Apr 2022 09:59:39 +0000 (17:59 +0800)]
wdt: nuvoton: Add support for Nuvoton
Add watchdog controller driver for NPCM7xx/npcm8xx
the wdt design of npcm750 and npcm845 is the same.
so the driver can work on npcm750 and npcm845.
about npcm845 wdt dtsi i will followed kernel dts name
to use nuvoton,npcm750-wdt.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Philippe Reynes [Wed, 9 Mar 2022 13:56:19 +0000 (14:56 +0100)]
doc: device-tree-bindings: watchdog: document common properties
Adds simple documentation about common properties for watchdog
in the device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tom Rini [Thu, 21 Apr 2022 23:55:38 +0000 (19:55 -0400)]
Merge branch '2022-04-21-further-cleanups'
- Fix SPL_SYS_MALLOC_SIMPLE and non-SPL_FRAMEWORK boards (a large number
of PowerPC platforms)
- Remove duplication of crc16 functionality
- Migrate COUNTER_FREQUENCY to CONFIG_COUNTER_FREQUENCY and have it in
Kconfig
Heiko Thiery [Thu, 24 Feb 2022 20:07:14 +0000 (21:07 +0100)]
ARM: imx: imx8mn-evk: change environment address variables
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:43 +0000 (12:23 +0800)]
configs: imx: drop IMX_FEC_BASE
IMX_FEC_BASE is not used in these boards, so drop it.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Ying-Chun Liu (PaulLiu) [Wed, 20 Apr 2022 15:37:07 +0000 (23:37 +0800)]
imx8mm-cl-iot-gate: Remove redundant board_fix_fdt()
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit
35bb60787b88. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Peng Fan [Wed, 13 Apr 2022 09:47:22 +0000 (17:47 +0800)]
arm: set cntfrq_el0 if CONFIG_COUNTER_FREQUENCY is valid
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Peng Fan [Wed, 13 Apr 2022 09:47:21 +0000 (17:47 +0800)]
include/configs: drop COUNTER_FREQUENCY
Since we have CONFIG_COUNTER_FREQUENCY enabled, no need COUNTER_FREQUENCY
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 13 Apr 2022 09:47:20 +0000 (17:47 +0800)]
configs: set CONFIG_COUNTER_FREQUENCY
Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in
config header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: Re-run migration]
Peng Fan [Wed, 13 Apr 2022 09:47:19 +0000 (17:47 +0800)]
arch: arm: Kconfig: set default COUNTER_FREQUENCY
Set default COUNTER_FREQUENCY according to config header file
under include/configs/
i.MX6UL/ULL/7D/8QM/8QXP all has system counter frequency run at 8MHz,
so set default value for them.
SUNXI/EXYNOS/ROCKCHIP_RK3128/ROCKCHIP_RK3288/ROCKCHIP_RK322X/ROCKCHIP_RK3036
at 24MHz. ARCH_LX2160A at 25MHz
ARCH_ZYNQMP at 100MHz
Peng Fan [Wed, 13 Apr 2022 09:47:18 +0000 (17:47 +0800)]
arch: arm: move COUNTER_FREQUENCY from versal to arm
Make COUNTER_FREQUENCY usable to armv8 and armv7-a, not limited to
versal. And update help message.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Wed, 13 Apr 2022 09:47:17 +0000 (17:47 +0800)]
xilinx: versal: board: use CONFIG_COUNTER_FREQUENCY
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Pali Rohár [Tue, 12 Apr 2022 09:20:44 +0000 (11:20 +0200)]
misc: atsha204a: Remove duplicate CRC-16 implementation
ATSHA204A uses bit-reversed checksum of standard CRC-16 with polynomial
x^16 + x^15 + x^2 + 1.
This ATSHA204A specific checksum can be calculated just by using common
U-Boot functions bitrev16() and crc16().
So replace custom driver CRC-16 implementation by common U-Boot functions.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 12 Apr 2022 09:20:43 +0000 (11:20 +0200)]
fs: ext4: Use CRC-16 implementation from linux/crc16.h
Implementation in linux/crc16.h provides standard CRC-16 algorithm with
polynomial x^16 + x^15 + x^2 + 1. Use it and remove duplicate ext4 CRC-16
specific code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 12 Apr 2022 09:20:42 +0000 (11:20 +0200)]
crc16: Move standard CRC-16 implementation from ubifs to lib
This implementation provides standard CRC-16 algorithm with polynomial
x^16 + x^15 + x^2 + 1.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 12 Apr 2022 09:20:41 +0000 (11:20 +0200)]
crc16: Rename fs/ubifs/crc16.h to include/linux/crc16.h
File fs/ubifs/crc16.h is standard linux's crc16.h include file. So move it
from fs/ubifs to include/linux where are also other linux include files.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Tue, 12 Apr 2022 09:20:40 +0000 (11:20 +0200)]
crc16-ccitt: Rename file with CRC-16-CCITT implementation to crc16-ccitt.c
U-Boot CRC-16 implementation uses polynomial x^16 + x^12 + x^5 + 1 which is
not standard CRC-16 algorithm, but it is known as CRC-16-CCITT. Rename file
crc16.c to crc16-ccitt.c to reduce confusion.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Pali Rohár [Fri, 8 Apr 2022 08:28:05 +0000 (10:28 +0200)]
SPL: Do not enable SPL_SYS_MALLOC_SIMPLE without SPL_FRAMEWORK by default
On P2020 board is SPL malloc simple always failing with error and loops:
SD boot...
alloc space exhausted
Bad trap at PC:
f8f8b5f0, SR: 21200, vector=d00
NIP:
00000000 XER:
00000000 LR:
00000000 REGS:
f8f8b5f0 TRAP:
20000000 DAR:
00000000
MSR:
00021200 EE: 0 PR: 0 FP: 0 ME: 1 IR/DR: 00
GPR00:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
GPR08:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
GPR16:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
GPR24:
00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Call backtrace:
Exception in kernel pc
f8f8b5f0 signal 0
Inspection showed that gd->malloc_limit is zero. And it is because
generally SPL_FRAMEWORK initialize SPL's gd->malloc_limit. But when
SPL_FRAMEWORK is not enabled then in most cases nobody initialize
gd->malloc_limit and so SPL malloc simple does not work.
So disable SPL_SYS_MALLOC_SIMPLE by default when SPL_FRAMEWORK is not
enabled. SPL_SYS_MALLOC_SIMPLE can be disabled only by setting
SPL_SYS_MALLOC_F_LEN to zero. So do it.
This change fixes SPL error "alloc space exhausted" on P2020 board.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tom Rini [Thu, 21 Apr 2022 15:44:54 +0000 (11:44 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mrvl_uart.sh: Remove script (Pali)
- Fix Espressobin build for configs where ENV is not in SPI (Rogier)
- mvebu: a37xx: Add support for reading OTP (Pali)
- mvebu: uDPU: Ethernet fixes and misc DT and defconfig changes (Robert)
- mvebu: Add support for reading LD0 and LD1 eFuse (Pali)
- kwboot: Replace fstat()+st_size by lseek()+SEEK_END (Pali)
- mvebu: turris_omnia: Enable CONFIG_CMD_FUSE (Pali)
- arm: Add CONFIG_SPL_SYS_NO_VECTOR_TABLE used on 32bit MVEBU (Pali)
- mvebu: a37xx: Add support for writing Security OTP values (Pali)
- mvebu: turris: Misc enhancements and cleanups / fixes (Pali)
- Sheevaplug : Use Marvell uclass mvgbe and PHY driver for Ethernet (Tony)
Tom Rini [Thu, 21 Apr 2022 14:56:58 +0000 (10:56 -0400)]
Merge branch '2022-04-21-assorted-improvements'
- For the environment, add a arch_env_get_location hook and make use of
it on some NXP platforms (so that boards can override SoCs).
- Remove some unused squashfs code from SPL
- Resync am335x beaglebone related DTS files
- Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
Ye Li [Tue, 19 Apr 2022 09:13:25 +0000 (14:43 +0530)]
imx: Fix build error
Fix wrong environment.h and remove DECLARE_GLOBAL_DATA_PTR
Fixes:
30e39ac7c9 (imx: imx7 Support for Manufacturing Protection)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Ye Li [Tue, 19 Apr 2022 09:13:24 +0000 (14:43 +0530)]
imx: Update FSL_MFGPROT config for iMX8M
Update the Kconfig and Makefile to allow build for iMX8M and
restrict the build only in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Gaurav Jain [Tue, 19 Apr 2022 05:22:28 +0000 (10:52 +0530)]
crypto/fsl: add invalidate_dcache_range for hash output buffer
HW accelerated hash operations are giving incorrect hash output.
so invalidate cache lines to avoid cache overwriting in DDR memory region.
caam_hash()
-moved address alignment check in the beginning of function.
-added invalidate_dcache_range for pout buffer before running descriptor.
Fixes:
d7af2baa49 (crypto/fsl: Fix HW accelerated hash commands)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Mon, 18 Apr 2022 17:15:08 +0000 (14:15 -0300)]
doc: imx8mn_evk: Do not export ATF_LOAD_ADDR
The imx8mn_evk target have been converted to use binman.
With the binman approach the ATF load address is described via
devicetree, so remove the now unneeded instruction of exporting
ATF_LOAD_ADDR.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Mon, 18 Apr 2022 17:15:07 +0000 (14:15 -0300)]
imx8mn_evk: Enable cache in SPL
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Michael Trimarchi [Mon, 18 Apr 2022 06:53:36 +0000 (08:53 +0200)]
board: bsh: imx8mn_bsh_smm_s2/s2pro: enable DM_SERIAL
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Tim Harvey [Fri, 15 Apr 2022 20:41:54 +0000 (13:41 -0700)]
arm: dts: imx8mp: add of-list support to common imx8mp-u-boot.dtsi
Add support for OF-LIST to common imx8mp-u-boot.dtsi so that it can
be used with boards that have multiple DTB's.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Gaurav Jain [Fri, 15 Apr 2022 11:22:34 +0000 (16:52 +0530)]
crypto/fsl: Clear the memory when blob decapsulation fails
issue: blob decapsulation operation store the decrypted data
in memory even if ICV check failed.
fix: clear the blob data output memory.
Fixes:
c5de15cbc8 (crypto/fsl: Add command for encapsulating/decapsulating blobs)
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Tested-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Peng Fan [Fri, 15 Apr 2022 04:35:36 +0000 (12:35 +0800)]
imx: imx8mq-evk: enable CONFIG_DM_SERIAL
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:35:35 +0000 (12:35 +0800)]
imx: imx8mn_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:35:34 +0000 (12:35 +0800)]
imx: imx8mm_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:35:33 +0000 (12:35 +0800)]
imx: imx8mp_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:42 +0000 (12:23 +0800)]
scripts: config_whitelist: drop CONFIG_MMCROOT
Drop CONFIG_MMCROOT, no users now.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:41 +0000 (12:23 +0800)]
configs: drop CONFIG_MMCROOT
CONFIG_MMCROOT is only used to set mmcroot, no need a dedicated macro.
Script as below
"
for i in `ls include/configs/*.h`
do
mmcroot=`sed -n '/define.*MMCROOT/ p' $i | awk -F\" '{ print $2;}'`
if [ ! -n "$mmcroot" ]; then
continue
fi
sed -i '/define.*MMCROOT/ d' $i
sed -i 's,\" CONFIG_MMCROOT \",'$mmcroot',g' $i
done
"
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sean Anderson [Tue, 12 Apr 2022 14:59:04 +0000 (10:59 -0400)]
treewide: Enable SPL_SEPARATE_BSS if SPL_BSS_START_ADDR is used
If .bss does not immediately follow the end of the image, then
CONFIG_SPL_SEPARATE_BSS must be selected. Typically, the location of bss
is specified by using CONFIG_SPL_BSS_START_ADDR in a linker script. On
these arches, CONFIG_SPL_SEPARATE_BSS should be enabled. If there is an
option to use an alternate boot script (e.g. CONFIG_SPL_LDSCRIPT is just
a default), just imply. If there is not, select.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Paul Barker [Mon, 11 Apr 2022 15:42:01 +0000 (15:42 +0000)]
board: ti: am335x: Add support for BBE Extended WiFi
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:42:00 +0000 (15:42 +0000)]
board: ti: am335x: Add BBE Lite support
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Paul Barker [Mon, 11 Apr 2022 15:41:59 +0000 (15:41 +0000)]
arm: dts: Resync dts for BeagleBone and derivatives
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit
c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Pali Rohár [Wed, 6 Apr 2022 21:34:00 +0000 (23:34 +0200)]
fs: Allow to compile FS_SQUASHFS only for proper U-Boot
CONFIG_SPL_FS_SQUASHFS cannot be disabled when CONFIG_FS_SQUASHFS is
enabled. Fix it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Marek Vasut [Wed, 6 Apr 2022 00:21:34 +0000 (02:21 +0200)]
ARM: imx: imx8m: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:33 +0000 (02:21 +0200)]
armv8: layerscape: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Marek Vasut [Wed, 6 Apr 2022 00:21:32 +0000 (02:21 +0200)]
env: Implement lower priority arch_env_get_location()
Currently there is only one way to override desired environment location,
by implementing env_get_location(). This is increasingly being conflated
both on board level and architecture level, which leads to a problem on
boards where this function is already implemented on architecture level,
since those boards have no way to override this environment location on
board level anymore.
Implement arch_env_get_location() function which is architecture specific
and should only ever be implemented in architecture code. This function
has lower priority than env_get_location(), which should only ever be
implemented in board code, and which overrides the arch_env_get_location()
architecture environment selection.
This way, architecture can define its default environment chooser, while
board can now override it as needed at all times.
There is no functional change, since env_get_location() simply returns
arch_env_get_location(), and arch_env_get_location() implements the
current env_get_location() default content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:40 +0000 (12:23 +0800)]
configs: phycore_imx8mm/p: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:39 +0000 (12:23 +0800)]
configs: imx8mm/n_venice: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:38 +0000 (12:23 +0800)]
configs: verdin-imx8m: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:37 +0000 (12:23 +0800)]
configs: imx8qm/qxp_evk: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:36 +0000 (12:23 +0800)]
configs: mx7dsabresd: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
CONFIG_SYS_FSL_USDHC_NUM
CONFIG_SYS_FSL_ESDHC_ADDR
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:35 +0000 (12:23 +0800)]
configs: mx6sxsabresd: drop CONFIG_SYS_FSL_USDHC_NUM
With DM_MMC, CONFIG_SYS_FSL_USDHC_NUM is not needed.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:34 +0000 (12:23 +0800)]
configs: imx8mn_evk: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:33 +0000 (12:23 +0800)]
configs: imx8mp_evk: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Peng Fan [Fri, 15 Apr 2022 04:23:32 +0000 (12:23 +0800)]
configs: imx8mm_evk: drop unused SDHC macro
With SPL_DM_MMC and DM_MMC, the two macros not needed, drop it.
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Marek Vasut [Thu, 14 Apr 2022 13:51:46 +0000 (15:51 +0200)]
ARM: imx: imx8m: Fix board_get_usable_ram_top()
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.
The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.
Fixes:
e27bddff4b9 ("imx8m: Restrict usable memory to space below 4G boundary")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Ian Ray [Thu, 14 Apr 2022 11:05:46 +0000 (14:05 +0300)]
configs: ge_bx50v3: remove CONFIG_PCIE_IMX_POWER_GPIO
This GPIO is actually an input "Q7_3V3_PCIE_WAKE#_IN" not an output, so
remove the misleaading and incorrect definition.
Cc: Tim Harvey <tharvey@gateworks.com> (re: pci: imx: use vpcie-supply if defined by device-tree)
Signed-off-by: Ian Ray <ian.ray@ge.com>
Tim Harvey [Wed, 13 Apr 2022 22:57:37 +0000 (15:57 -0700)]
pci: imx: remove weak overrides no longer used
There are no users of the imx6_pcie_toggle_power and imx6_pcie_toggle_reset
weak overrides and as these functions are able to be handled now via dt
properties lets remove these.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>