drm/rockchip: Avoid race with vblank count increment

Since VOP does not have a hardware vblank count register, the ongoing
commit might be racing with a requested vblank interrupt, which would
increment the software vblank counter before the changes being committed
actually happen.

To avoid this, we can extend .atomic_flush(), so after it sets cfg_done
bit, it polls the vblank interrupt bit until it's inactive to make sure
that any old vblank interrupt gets to the handler and then uses
synchronize_irq(vop->irq) to make sure the handler finishes running.

The polling case should happen very rarely, but even if, the total wait
time should be relatively low and in practice almost equal to the vop
hardirq handler running time.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>

drm/rockchip: Get rid of some unnecessary code

Current code implements prepare_fb and cleanup_fb callbacks only to
grab/release fb references, which is already done by atomic framework
when creating/destryoing plane state. Let's remove these
unused bits.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>

drm/rockchip: Clear interrupt status bits before enabling

The enable register only masks the raw status bits to signal CPU
interrupt only for enabled interrupts. The status bits are activated
regardless of the enable register. This means that we might have an old
interrupt event queued, which we are not interested in. To avoid getting
a spurious interrupt signalled, we have to clear the old bit before we
update the enable register.

Signed-off-by: Tomasz Figa <tfiga@chromium.org>

drm/rockchip: Fix up bug in psr state machine

The ->set() callback would always be called when transitioning
from FLUSH->DISABLE since we assign state to psr->state right
above the skip condition.

Reported-by: Daniel Kurtz <djkurtz@chromium.org>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/bridge: analogix_dp: Remove duplicated code

Remove code for reading the EDID and DPCD fields and use the helpers
instead.

Besides the obvious code reduction, other helpers are being added to the
core that could be used in this driver and will be good to be able to
use them instead of duplicating them.

Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Yakir Yang <ykk@rock-chips.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Archit Taneja <architt@codeaurora.org>

drm/rockchip: Reduce psr flush time to 100ms

3 seconds is a bit too conservative, drop this to 100ms for
better power savings.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

drm/rockchip: Don't key off vblank for psr

Instead of keying off vblank for psr, just flush every time
we get an atomic update. This ensures that cursor updates
will properly disable psr (without turning vblank on/off),
and unifies the paths between fb_dirty and atomic psr
enable/disable.

Reviewed-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>

Merge branch 'for-next' of git.agner.ch/git/linux-drm-fsl-dcu into drm-next

fsl-dcu fixes.

* 'for-next' of http://git.agner.ch/git/linux-drm-fsl-dcu:
  drm/fsl-dcu: disable clock on error path
  drm/fsl-dcu: use PTR_ERR_OR_ZERO() to simplify the code
  drm/fsl-dcu: fix endian issue when using clk_register_divider

Merge tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux into drm-next

imx-drm active plane reconfiguration, cleanup, FSU/IC/IRT/VDIC support

- add active plane reconfiguration support (v4),
  use the atomic_disable callback
- stop calling disable_plane manually in the plane destroy path
- let mode cleanup destroy mode objects on driver unbind
- drop deprecated load/unload drm_driver ops
- add exclusive fence to plane state, so the atomic helper can
  wait on them, remove the open-coded fence wait from imx-drm
- add low level deinterlacer (VDIC) support
- add support for channel linking via the frame synchronisation unit (FSU)
- add queued image conversion support for memory-to-memory scaling, rotation,
  and color space conversion, using IC and IRT.

* tag 'imx-drm-next-2016-09-19' of git://git.pengutronix.de/git/pza/linux:
  gpu: ipu-v3: Add queued image conversion support
  gpu: ipu-v3: Add ipu_rot_mode_is_irt()
  gpu: ipu-v3: fix a possible NULL dereference
  drm/imx: parallel-display: detach bridge or panel on unbind
  drm/imx: imx-ldb: detach bridge on unbind
  drm/imx: imx-ldb: detach panel on unbind
  gpu: ipu-v3: Add FSU channel linking support
  gpu: ipu-v3: Add Video Deinterlacer unit
  drm/imx: add exclusive fence to plane state
  drm/imx: fold ipu_plane_disable into ipu_disable_plane
  drm/imx: don't destroy mode objects manually on driver unbind
  drm/imx: drop deprecated load/unload drm_driver ops
  drm/imx: don't call disable_plane in plane destroy path
  drm/imx: Add active plane reconfiguration support
  drm/imx: Use DRM_PLANE_COMMIT_NO_DISABLE_AFTER_MODESET flag
  drm/imx: ipuv3-crtc: Use the callback ->atomic_disable instead of ->disable
  gpu: ipu-v3: Do not wait for DMFC FIFO to clear when disabling DMFC channel

Merge tag 'drm-intel-next-2016-09-19' of git://anongit.freedesktop.org/drm-intel into drm-next

- refactor the sseu code (Imre)
- refine guc dmesg output (Dave Gordon)
- more vgpu work
- more skl wm fixes (Lyude)
- refactor dpll code in prep for upfront link training (Jim Bride et al)
- consolidate all platform feature checks into intel_device_info (Carlos Santa)
- refactor elsp/execlist submission as prep for re-submission after hang
  recovery and eventually scheduling (Chris Wilson)
- allow synchronous gpu reset handling, to remove tricky/impossible/fragile
  error recovery code (Chris Wilson)
- prep work for nonblocking (execlist) submission, using fences to track
  depencies and drive elsp submission (Chris Wilson)
- partial error recover/resubmission of non-guilty batches after hangs (Chris Wilson)
- full dma-buf implicit fencing support (Chris Wilson)
- dp link training fixes (Jim, Dhinkaran, Navare, ...)
- obey dp branch device pixel rate/bpc/clock limits (Mika Kahola), needed for
  many vga dongles
- bunch of small cleanups and polish all over, as usual

[airlied: printing macros collided]

* tag 'drm-intel-next-2016-09-19' of git://anongit.freedesktop.org/drm-intel: (163 commits)
  drm/i915: Update DRIVER_DATE to 20160919
  drm: Fix DisplayPort branch device ID kernel-doc
  drm/i915: use NULL for NULL pointers
  drm/i915: do not use 'false' as a NULL pointer
  drm/i915: make intel_dp_compute_bpp static
  drm: Add DP branch device info on debugfs
  drm/i915: Update bits per component for display info
  drm/i915: Check pixel rate for DP to VGA dongle
  drm/i915: Read DP branch device SW revision
  drm/i915: Read DP branch device HW revision
  drm/i915: Cleanup DisplayPort AUX channel initialization
  drm: Read DP branch device id
  drm: Helper to read max bits per component
  drm: Helper to read max clock rate
  drm: Drop VGA from bpc definitions
  drm: Add missing DP downstream port types
  drm/i915: Add ddb size field to device info structure
  drm/i915/guc: general tidying up (submission)
  drm/i915/guc: general tidying up (loader)
  drm/i915: clarify PMINTRMSK/pm_intr_keep usage
  ...

Merge branch 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux into drm-next

More radeon and amdgpu changes for 4.9. Highlights:
- Initial SI support for amdgpu (controlled by a Kconfig option)
- misc ttm cleanups
- runtimepm fixes
- S3/S4 fixes
- power improvements
- lots of code cleanups and optimizations

* 'drm-next-4.9' of git://people.freedesktop.org/~agd5f/linux: (151 commits)
  drm/ttm: remove cpu_address member from ttm_tt
  drm/radeon/radeon_device: remove unused function
  drm/amdgpu: clean function declarations in amdgpu_ttm.c up
  drm/amdgpu: use the new ring ib and dma frame size callbacks (v2)
  drm/amdgpu/vce3: add ring callbacks for ib and dma frame size
  drm/amdgpu/vce2: add ring callbacks for ib and dma frame size
  drm/amdgpu/vce: add common ring callbacks for ib and dma frame size
  drm/amdgpu/uvd6: add ring callbacks for ib and dma frame size
  drm/amdgpu/uvd5: add ring callbacks for ib and dma frame size
  drm/amdgpu/uvd4.2: add ring callbacks for ib and dma frame size
  drm/amdgpu/sdma3: add ring callbacks for ib and dma frame size
  drm/amdgpu/sdma2.4: add ring callbacks for ib and dma frame size
  drm/amdgpu/cik_sdma: add ring callbacks for ib and dma frame size
  drm/amdgpu/si_dma: add ring callbacks for ib and dma frame size
  drm/amdgpu/gfx8: add ring callbacks for ib and dma frame size
  drm/amdgpu/gfx7: add ring callbacks for ib and dma frame size
  drm/amdgpu/gfx6: add ring callbacks for ib and dma frame size
  drm/amdgpu/ring: add an interface to get dma frame and ib size
  drm/amdgpu/sdma3: drop unused functions
  drm/amdgpu/gfx6: drop gds_switch callback
  ...

drm/i915: Update DRIVER_DATE to 20160919

Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Merge tag 'topic/drm-misc-2016-09-19' of git://anongit.freedesktop.org/drm-intel into drm-next

Just random misc stuff that Sean/Sumit&Archit picked up while I relaxed.
Well except for one commit:

* tag 'topic/drm-misc-2016-09-19' of git://anongit.freedesktop.org/drm-intel:
  drm: Only use compat ioctl for addfb2 on X86/IA64
  drm/qxl: squash lines for simple wrapper functions
  drm/bridge: analogix_dp: squash lines for simple wrapper functions
  drm/radeon: squash lines for simple wrapper functions
  drm/amdgpu: squash lines for simple wrapper functions
  dma-buf/sync-file: Avoid enable fence signaling if poll(.timeout=0)
  drm/fence: allow fence waiting to be interrupted by userspace
  drm: Move property validation to a helper, v2.
  drm/bridge: adv7511: add support for the 2nd chip

gpu: ipu-v3: Add queued image conversion support

This patch implements image conversion support using the IC tasks, with
tiling to support scaling to and from images up to 4096x4096. Image
rotation is also supported. Image conversion requests are added to
a run queue under the IC tasks.

The internal API is subsystem agnostic (no V4L2 dependency except
for the use of V4L2 fourcc pixel formats).

Callers prepare for image conversion by calling
ipu_image_convert_prepare(), which initializes the parameters of
the conversion. The caller passes in the ipu and IC task to use for
the conversion, the input and output image formats, a rotation mode,
and a completion callback and completion context pointer:

struct ipu_image_converter_ctx *
ipu_image_convert_prepare(struct ipu_soc *ipu, enum ipu_ic_task ic_task,
                          struct ipu_image *in, struct ipu_image *out,
                          enum ipu_rotate_mode rot_mode,
                          ipu_image_converter_cb_t complete,
                          void *complete_context);

A new conversion context is created that is added to an IC task
context queue. The caller is given the new conversion context,
which can then be passed to the further APIs:

int ipu_image_convert_queue(struct ipu_image_converter_run *run);

This queues the given image conversion request run to a run queue,
and starts the conversion immediately if the run queue is empty. Only
the physaddr's of the input and output image buffers are needed,
since the conversion context was created previously with
ipu_image_convert_prepare(). When the conversion completes, the run
pointer is returned to the completion callback.

void ipu_image_convert_abort(struct ipu_image_converter_ctx *ctx);

This will abort any active or pending conversions for this context.
Any currently active or pending runs belonging to this context are
returned via the completion callback with an error status.

void ipu_image_convert_unprepare(struct ipu_image_converter_ctx *ctx);

Unprepares the conversion context. Any active or pending runs will
be aborted by calling ipu_image_convert_abort().

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

gpu: ipu-v3: Add ipu_rot_mode_is_irt()

Add a macro that returns boolean true if the given ipu_rotate_mode
requires the use of the Image Rotator.

Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

gpu: ipu-v3: fix a possible NULL dereference

of_match_device could return NULL, and so cause a NULL pointer
dereference later.

For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.

Testing the return value of of_device_get_match_data is also necessary
for avoiding a second NULL deref later on devtype.

Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>

drm/ttm: remove cpu_address member from ttm_tt

Patch 3d50d4dcb0 exposed the CPU address of DMA-allocated pages as
returned by dma_alloc_coherent because Nouveau on Tegra needed it.

This is not required anymore - as there were no other users for it,
remove it and save some memory for everyone.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/radeon_device: remove unused function

We get 2 warnings when building kernel with W=1:
drivers/gpu/drm/radeon/radeon_device.c:1961:5: warning: no previous prototype for 'radeon_debugfs_init' [-Wmissing-prototypes]
drivers/gpu/drm/radeon/radeon_device.c:1966:6: warning: no previous prototype for 'radeon_debugfs_cleanup' [-Wmissing-prototypes]

In fact, these functions are dummy, but can be removed,
so this patch removes them.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: clean function declarations in amdgpu_ttm.c up

We get 2 warnings when building kernel with W=1:

drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.c:985:5: warning: no previous prototype for 'amdgpu_ttm_init' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.c:1092:6: warning: no previous prototype for 'amdgpu_ttm_fini' [-Wmissing-prototypes]

In fact, both functions are declared in
drivers/gpu/drm/amd/amdgpu/amdgpu_ttm.c, but should be declared in
a header file, thus can be recognized in other file.

So this patch moves the declarations into
drivers/gpu/drm/amd/amdgpu/amdgpu.h.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use the new ring ib and dma frame size callbacks (v2)

Use them to more accurately determine the ring size required
for ib submission.

v2: drop extra alignment

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vce3: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vce2: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vce: add common ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/uvd6: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/uvd5: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/uvd4.2: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/sdma3: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/sdma2.4: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/cik_sdma: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/si_dma: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx8: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx7: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx6: add ring callbacks for ib and dma frame size

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/ring: add an interface to get dma frame and ib size

Used to properly calculate space on the ring for ib submissions.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/sdma3: drop unused functions

These are not used yet.

Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx6: drop gds_switch callback

GDS works differently on GFX6, plus the callback was
empty.

Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx6: add ring_emit_cntxcntl

Missing for gfx6.

Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/gfx6: drop duplicate code

The compute functions just called the gfx functions, drop
the wrapper.

Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/si: fix ring size for compute

We switched the other asics, but missed this.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: Partially revert change initialize platform caps

partially revert commit I36f3c9e3a28cbf290652edfb6e19109da660c4f1
this will lead APU can't work.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: not set cg for vce/uvd in late init.

no need to set cg for uvd/vce in late init.
As when ring test, uvd/vce's dpm will be enabled/disabled.
the cg will be set.

fix issue suspend when play video or encode, then resume back,
the clock will be bypassed on Polaris/Fiji.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add pptable point check before use it

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add pp_table_version in hwmgr.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: rename tonga_processpptable* to processpptable_v1_0*.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/vi: Use correct external_rev_id for stoney

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Jordan Lazare <Jordan.Lazare@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm: Fix DisplayPort branch device ID kernel-doc

Fix missing parameter description for DisplayPort branch device ID.
This fixes warning of "No description found for parameter 'id[6]'" when
creating documentation by 'make htmldocs'.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
References: https://lists.freedesktop.org/archives/intel-gfx/2016-September/106645.html
Fixes: 266d783baaf5 ("drm: Read DP branch device id")
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1474022355-29990-1-git-send-email-mika.kahola@intel.com

drm/i915: use NULL for NULL pointers

Fix sparse warning:

drivers/gpu/drm/i915/i915_cmd_parser.c:987:72: warning: Using plain
integer as NULL pointer

Fixes: 52a42cec4b70 ("drm/i915/cmdparser: Accelerate copies from WC memory")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473946137-1931-4-git-send-email-jani.nikula@intel.com

drm/i915: do not use 'false' as a NULL pointer

Fixes sparse warning:

drivers/gpu/drm/i915/intel_dpll_mgr.c:1712:24: warning: Using plain
integer as NULL pointer

Fixes: a277ca7dc01d ("drm/i915: Split bxt_ddi_pll_select()")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473946137-1931-2-git-send-email-jani.nikula@intel.com

drm/i915: make intel_dp_compute_bpp static

Fix sparse warning:

drivers/gpu/drm/i915/intel_dp.c:1527:5: warning: symbol
'intel_dp_compute_bpp' was not declared. Should it be static?

Fixes: f9bb705e65f6 ("drm/i915: Update bits per component for display info")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473946137-1931-1-git-send-email-jani.nikula@intel.com

drm: Only use compat ioctl for addfb2 on X86/IA64

Similar to struct drm_update_draw, struct drm_mode_fb_cmd2 has an
unaligned 64 bit field (modifier). This get packed differently between
32 bit and 64 bit modes on architectures that can handle unaligned 64
bit access (X86 and IA64).  Other architectures pack the structs the
same and don't need the compat wrapper. Use the same condition for
drm_mode_fb_cmd2 as we use for drm_update_draw.

Note that only the modifier will be packed differently between compat
and non-compat versions.

Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Kristian H. Kristensen <hoegsberg@chromium.org>
[seanpaul added not at bottom of commit msg re: modifier]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473801645-116011-1-git-send-email-hoegsberg@chromium.org

drm/qxl: squash lines for simple wrapper functions

Remove unneeded variables and assignments.

Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473863952-7658-5-git-send-email-yamada.masahiro@socionext.com

drm/bridge: analogix_dp: squash lines for simple wrapper functions

Remove unneeded variables and assignments.

Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[seanpaul added analogix prefix to subject]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473863952-7658-4-git-send-email-yamada.masahiro@socionext.com

drm/radeon: squash lines for simple wrapper functions

Remove unneeded variables and assignments.

Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473863952-7658-3-git-send-email-yamada.masahiro@socionext.com

drm/amdgpu: squash lines for simple wrapper functions

Remove unneeded variables and assignments.

Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1473863952-7658-2-git-send-email-yamada.masahiro@socionext.com

drm: Add DP branch device info on debugfs

Read DisplayPort branch device info from through debugfs
interface.

v2: use drm_dp_helper routines to collect data
v3: cleanup to match the drm_dp_helper.c patches introduced
    earlier in this series
v4: move DP branch device info to function 'intel_dp_branch_device_info()'
v5: initial step to move debugging info from intel_dp. to drm_dp_helper.c (Daniel)
v6: read hw and sw revision without using specific drm_dp_helper routines
v7: indentation fixes (Jim Bride)

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-12-git-send-email-mika.kahola@intel.com

drm/i915: Update bits per component for display info

DisplayPort branch device may define max supported bits per
component. Update display info based on this value if bpc
is defined.

v2: cleanup to match the drm_dp_helper.c patches introduced
    earlier in this series
v3: Fill bpc for connector's display info in separate
    drm_dp_helper function (Daniel)
v4: remove updating bpc for display info as it may be overridden
    when parsing EDID. Instead, check bpc for DP branch device
    during compute_config
v5: Indentation fixes (Jim Bride)

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-11-git-send-email-mika.kahola@intel.com

drm/i915: Check pixel rate for DP to VGA dongle

Filter out a mode that exceeds the max pixel rate setting
for DP to VGA dongle. This is defined in DPCD register 0x81
if detailed cap info i.e. info field is 4 bytes long and
it is available for DP downstream port.

The register defines the pixel rate divided by 8 in MP/s.

v2: DPCD read outs and computation moved to drm (Ville, Daniel)
v3: Sink pixel rate computation moved to drm_dp_max_sink_dotclock()
    function (Daniel)
v4: Use of drm_dp_helper.c routines to compute max pixel clock (Ville)
v5: Use of intel_dp->downstream_ports to read out port capabilities.
    Code restructuring (Ville)
v6: Move DP branch device check to drm_dp_helper.c (Daniel)
v7: Cleanup as suggested by Ville

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-10-git-send-email-mika.kahola@intel.com

drm/i915: Read DP branch device SW revision

SW revision is mandatory field for DisplayPort branch
devices. This is defined in DPCD register fields 0x50A
and 0x50B.

v2: move drm_dp_ds_revision structure to be part of
    drm_dp_link structure (Daniel)
v3: remove dependency to drm_dp_helper but instead parse
    DPCD and print SW revision info to dmesg (Ville)
v4: commit message fix (Jim Bride)

Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-9-git-send-email-mika.kahola@intel.com

drm/i915: Read DP branch device HW revision

HW revision is mandatory field for DisplayPort branch
devices. This is defined in DPCD register field 0x509.

v2: move drm_dp_ds_revision structure to be part of
    drm_dp_link structure (Daniel)
v3: remove dependency to drm_dp_helper but instead parse
    DPCD and print HW revision info to dmesg (Ville)

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-8-git-send-email-mika.kahola@intel.com

drm/i915: Cleanup DisplayPort AUX channel initialization

Let's remove reference to "struct intel_connector *connector"
in intel_dp_aux_init() function as it is no longer required.

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-7-git-send-email-mika.kahola@intel.com

drm: Read DP branch device id

Read DisplayPort branch device id string.

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-6-git-send-email-mika.kahola@intel.com

drm: Helper to read max bits per component

Helper routine to read out maximum supported bits per
component for DisplayPort legay converters.

v2: Return early if detailed port cap info is not available.
    Replace if-else ladder with switch-case (Ville)

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-5-git-send-email-mika.kahola@intel.com

drm: Helper to read max clock rate

Helper routine to read out maximum supported pixel rate
for DisplayPort legay VGA converter or TMDS clock rate
for other digital legacy converters. The helper returns
clock rate in kHz.

v2: Return early if detailed port cap info is not available.
    Replace if-else ladder with switch-case (Ville)

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-4-git-send-email-mika.kahola@intel.com

drm: Drop VGA from bpc definitions

Drop "VGA" from bits per component definitions as these
are also used by other standards such as DVI, HDMI,
DP++.

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-3-git-send-email-mika.kahola@intel.com

drm: Add missing DP downstream port types

Add missing DisplayPort downstream port types. The introduced
new port types are DP++ and Wireless.

Reviewed-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473419458-17080-2-git-send-email-mika.kahola@intel.com

drm/i915: Add ddb size field to device info structure

Adding the ddb size into the devide info will avoid
platform checks while computing wm.

v2: Added comment and WARN_ON if ddb size is zero.(Jani)
v3: Added WARN_ON at the right place.(Jani)

Suggested-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473931870-7724-1-git-send-email-m.deepak@intel.com

drm/i915/guc: general tidying up (submission)

Renaming to more consistent scheme, and updating comments, mostly
about i915_guc_wq_reserve(), aka i915_guc_wq_check_space().

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473711577-11454-4-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915/guc: general tidying up (loader)

Renaming to more consistent scheme, delete unused definitions

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473711577-11454-3-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: clarify PMINTRMSK/pm_intr_keep usage

No functional changes; just renaming a bit, tweaking a datatype,
prettifying layout, and adding comments, in particular in the
GuC setup code that touches this data.

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473711577-11454-2-git-send-email-david.s.gordon@intel.com
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/i915: Only expand COND once in wait_for()

Commentary from Chris Wilson's original version:

> I was looking at some wait_for() timeouts on a slow system, with lots of
> debug enabled (KASAN, lockdep, mmio_debug). Thinking that we were
> mishandling the timeout, I tried to ensure that we loop at least once
> after first testing COND. However, the double test of COND either side
> of the timeout check makes that unlikely. But we can do an equivalent
> loop, that keeps the COND check after testing for timeout (required so
> that we are not preempted between testing COND and then testing for a
> timeout) without expanding COND twice.
>
> The advantage of only expanding COND once is a dramatic reduction in
> code size:
>
>    text    data     bss     dec     hex
>    1308733    5184    1152 1315069  1410fd before
>    1305341    5184    1152 1311677  1403bd after

but it turned out that due to a missing iniitialiser, gcc had "gone
wild trimming undefined code" :( This version acheives a rather more
modest (but still worthwhile) gain of ~550 bytes.

Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Original-idea-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Zanoni, Paulo R <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1473855033-26980-1-git-send-email-david.s.gordon@intel.com
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>

drm/amdgpu: use explicit limit for VRAM<->GTT moves

Use an explicit limit when moving things around to
force address space allocation.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use explicit GTT limit for evictions

This way the address space gets allocated immediately.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: unbind GTT only when it is bound

Doesn't make much sense to clear the GTT when it was never filled.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add AMDGPU_BO_INVALID_OFFSET

An invalid offset to be used by custom VRAM/GGT manager when we
don't have an offset for an BO.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: validate size and offset of user fence BO

We need to validate the offset to make sure that we don't write after the BO.

Additional to that a page should be enough and can make address space
handling much easier.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: move placement structures into ttm_placement.h

Makes more sense to keep that together.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: remove unused placement flags

Either never used or not used in quite a while.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: rework handling of private mem types

Instead of keeping a bunch of potentially unused flags, just define
the start for private memory types and remove the rest.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/ttm: use ffs in ttm_mem_type_from_place

A bit pointless to search for the first bit set manually.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: handle runtime pm in fbcon (v2)

Ported from nouveau.

v2: re-enable runtime autosuspend in the error case

Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: handle runtime pm in fbcon (v2)

Ported from nouveau.

v2: re-enable runtime autosuspend in the error case

Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/si/dpm: fix symbol conflicts with radeon

Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/si/dpm: make a bunch of things static

remnants of the port from radeon.

Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay/polaris10: mark symbols static where possible

We get a few warnings when building kernel with W=1:
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/polaris10_clockpowergating.c:34:5: warning: no previous prototype
for 'polaris10_phm_powerup_uvd' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/polaris10_thermal.c:428:5: warning: no previous prototype
for 'tf_polaris10_thermal_setup_fan_table' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/polaris10_hwmgr.c:125:31: warning: no previous prototype
for 'cast_phw_polaris10_power_state' [-Wmissing-prototypes]
....

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay/fiji: mark symbols static where possible

We get a few warnings when building kernel with W=1:
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/fiji_hwmgr.c:1633:9: warning: no previous prototype
for 'fiji_get_voltage_index' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/fiji_hwmgr.c:5412:5: warning: no previous prototype
for 'fiji_check_states_equal' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../powerplay/hwmgr/fiji_thermal.c:424:5: warning: no previous prototype
for 'tf_fiji_thermal_setup_fan_table' [-Wmissing-prototypes]
....

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: mark symbols static where possible

We get a few warnings when building kernel with W=1:
drivers/gpu/drm/amd/amdgpu/cz_smc.c:51:5: warning: no previous prototype for 'cz_send_msg_to_smc_async' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/cz_smc.c:143:5: warning: no previous prototype for 'cz_write_smc_sram_dword' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/iceland_smc.c:124:6: warning: no previous prototype for 'iceland_start_smc' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/gfx_v8_0.c:3926:6: warning: no previous prototype for 'gfx_v8_0_rlc_stop' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/amdgpu_job.c:94:6: warning: no previous prototype for 'amdgpu_job_free_cb' [-Wmissing-prototypes]
....

In fact, these functions are only used in the file in which they are
declared and don't need a declaration, but can be made static.
So this patch marks these functions with 'static'.

Reviewed-by: Christian König <christian.koenig@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: add missing header dependencies

We get a few warnings when building kernel with W=1:
drivers/gpu/drm/amd/amdgpu/amdgpu_pll.c:113:6: warning: no previous prototype for 'amdgpu_pll_compute' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/cz_smc.c:38:10: warning: no previous prototype for 'cz_get_argument' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/cz_smc.c:302:5: warning: no previous prototype for 'cz_smu_start' [-Wmissing-prototypes]
....

In fact, these functions are declared in
drivers/gpu/drm/amd/amdgpu/atombios_i2c.h
drivers/gpu/drm/amd/amdgpu/amdgpu_pll.h
drivers/gpu/drm/amd/amdgpu/cz_dpm.h
drivers/gpu/drm/amd/amdgpu/vi_dpm.h.
So this patch adds missing header dependencies.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

amd/powerplay: use kmemdup instead of kmalloc + memcpy

Save a few clocks by replacing calls to kmalloc followed by memcpy
with a single call to kmemdup.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: delete duplicated function and definition.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: move smu related variable definitions to smumgr.

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: wrap get evv voltage functions

Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add helper function to get voltage id in votage table

Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: initialize platform caps in hwmgr_init.

Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add module parameter to mask pp features

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: add feature flags in hwmgr to enable/disable special features.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/powerplay: mark symbols static where possible on tonga/iceland.

Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: use error label to handle exceptional case

Use error label to decrease global item unref and make codes more
readable.

Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: update gart_pin_size if bo is in GTT

Signed-off-by: Flora Cui <Flora.Cui@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: bind GTT on demand

We don't really need the GTT table any more most of the time. So bind it
only on demand.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: fix GTT offset handling

Otherwise we run into problems on 32bit systems with more than 4GB GART.

Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>