Revert "drm/panel-simple: Add Samsung ATNA33XC20"

This reverts commit 4bfe6c8f7c23b01719671b69fd29b87a35ccd9d6.

This panel's power sequencing really can't be handled properly by
panel-simple because of the special sequencing needed for the EL_ON3
GPIO. The only way it was sorta working in the past was by trying to
jam that signal into the "enable-gpio", but that really wasn't a good
fit. We'll add a custom panel driver for this panel to do it right.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.4.Id9f076ec5f35633f8ce931051af268a04c45c075@changeid

drm/bridge: ti-sn65dsi86: Add some 100 us delays

The manual has always said that we need 100 us delays in a few
places. Though it hasn't seemed to be a big deal to skip these, let's
add them in case it makes something happier.

NOTE: this fixes no known issues but it seems good to make it right.

Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.3.I842d483139531aa4651da8338512fdf0171ff23c@changeid

drm/bridge: ti-sn65dsi86: Fix power off sequence

When testing with a panel that's apparently a little more persnickety
about the correct power sequence (specifically Samsung ATNA33XC20), we
found that the ti-sn65dsi86 was doing things just slightly wrong.

Looking closely at the ti-sn65dsi86's datasheet, the power off
sequence is supposed to be:
1. Clear VSTREAM_ENABLE bit
2. Stop DSI stream from GPU. DSI lanes must be placed in LP11 state.
3. Program the ML_TX_MODE to 0x0 (OFF)
4. Program the DP_NUM_LANES register to 0x0
5. Clear the DP_PLL_EN bit.
6. Deassert the EN pin.
7. Remove power from supply pins

Since we were doing the whole sequence in the "disable", I believe
that step #2 (stopping the DSI stream from the GPU) wasn't
happening. We also weren't setting DP_NUM_LANES to 0.

Let's fix this.

NOTE: things are a little asymmetric now. For instance, we turn the
PLL on in "enable" but now we're not turning it off until
"post_disable". It would seem to make sense to move the PLL turning on
to "pre_enable" to match. Unfortunately, I don't believe that's
allowed. It looks as if (in the non-refclk mode which probably nobody
is using) we have to wait until the MIPI clock is there before we can
enable the PLL. In any case, the way it is here won't really
hurt--it'll just leave the PLL on a little longer.

Fixes: a095f15c00e2 ("drm/bridge: add support for sn65dsi86 bridge driver")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.2.If8a8ec3bf1855cf0dbb62c005a71d6698c99c125@changeid

drm/dp: Don't zero PWMGEN_BIT_COUNT when driver_pwm_freq_hz not specified

The function drm_edp_backlight_init() is defined such that the
"driver_pwm_freq_hz" parameter is optional--it's 0 if you don't want
to futz with it. If you follow this variable through, you'll find out
that if it's 0 we won't ever set the "bl->pwmgen_bit_count", leaving
it as 0.

That means that before using it in drm_edp_backlight_enable() we need
to check to see if it's non-zero.

Programming this field to zero was confusing the panel I tested with
(Samsung ATNA33XC20). The backlight still worked somewhat but the
brightness values didn't correspond to what they should have been.

Fixes: 867cf9cd73c3 ("drm/dp: Extract i915's eDP backlight code into DRM helpers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730084534.v2.1.If017efce7116ae8ba015ed7def840c390a0e0c77@changeid

drm: clean up unused kerneldoc in drm_lease.c

The kerneldoc in drm_lease.c is unused because none of the functions
are driver interfaces as the symbols are not exported.

Since they aren't used and much of the existing comments don't provide
any insights (e.g. they just repeat the function name or list out the
function parameters), they should be removed to make them easier to
maintain and to make useful info more obvious.

As a note, many of the comments mention whether idr_mutex should be
held, but these are mostly redundant in cases where the function
contains lockdep assertions or grabs the mutex.

To simplify review, here's the reasoning behind each update.

drm_lease_owner:
function name is self-descriptive

_drm_find_lessee:
function name is self-descriptive

_drm_lease_held_master:
function name and signature are self-descriptive

_drm_has_leased:
kerneldoc is summarized into a comment because the function name could
be interpreted ambiguously (check if the object has been leased VS
check if the master has a lease on the object)

_drm_lease_held:
Retain the idr_mutex comment because the function does not directly
grab the mutex or use a lockdep assertion.
Otherwise, the function name is self-descriptive.

drm_lease_held:
function name is self-descriptive

drm_lease_filter_crtcs:
Kerneldoc is summarized into a comment because the function name could
be interpreted ambiguously (filter leases based on crtcs mask VS
filter crtcs mask based on leases)

drm_lease_create:
Kerneldoc removed.
Useful function details such as atomic leasing are retained.
Errno interpretations are useful and retained.

drm_lease_destroy:
function name is self-descriptive. Additional information is also
removed as they're already present as comments inside the function.

_drm_lease_revoke:
function name is self-descriptive

drm_lease_revoke:
function name is self-descriptive

drm_mode_create_lease_ioctl:
Kerneldoc removed, but useful function details retained.

drm_mode_list_lessees_ioctl:
function name is self-descriptive. Additional details restate what the
code does.

drm_mode_get_lease_ioctl:
Function summary retained to clarify that it's the leased objects that
are returned, not the lease structure.

drm_mode_revoke_lease_ioctl:
Kerneldoc removed, but useful function details retained.

Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730051759.1570630-1-desmondcheongzx@gmail.com

Merge tag 'amd-drm-next-5.15-2021-07-29' of https://gitlab.freedesktop.org/agd5f/linux into drm-next

amd-drm-next-5.15-2021-07-29:

amdgpu:
- VCN/JPEG power down sequencing fixes
- Various navi pcie link handling fixes
- Clockgating fixes
- Yellow Carp fixes
- Beige Goby fixes
- Misc code cleanups
- S0ix fixes
- SMU i2c bus rework
- EEPROM handling rework
- PSP ucode handling cleanup
- SMU error handling rework
- AMD HDMI freesync fixes
- USB PD firmware update rework
- MMIO based vram access rework
- Misc display fixes
- Backlight fixes
- Add initial Cyan Skillfish support
- Overclocking fixes suspend/resume

amdkfd:
- Sysfs leak fix
- Add counters for vm faults and migration
- GPUVM TLB optimizations

radeon:
- Misc fixes

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210730033455.3852-1-alexander.deucher@amd.com

Merge tag 'drm-msm-next-2021-07-28' of https://gitlab.freedesktop.org/drm/msm into drm-next

An early pull for v5.15 (there'll be more coming in a week or two),
consisting of the drm/scheduler conversion and a couple other small
series that one was based one.  Mostly sending this now because IIUC
danvet wanted it in drm-next so he could rebase on it.  (Daniel, if
you disagree then speak up, and I'll instead include this in the main
pull request once that is ready.)

This also has a core patch to drop drm_gem_object_put_locked() now
that the last use of it is removed.

[airlied: add NULL to drm_sched_init]

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGumRk7H88bqV=H9Fb1SM0zPBo5B7NsCU3jFFKBYxf5k+Q@mail.gmail.com

Merge tag 'drm-misc-next-2021-07-29' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

drm-misc-next for v5.15:

UAPI Changes:
- Add modifiers for arm fixed rate compression.

Cross-subsystem Changes:
- Assorted dt binding fixes.
- Convert ssd1307fb to json-schema.
- Update a lot of irc channels to point to OFTC, as everyone moved there.
- Fix the same divide by zero for asilantfb, kyro, rivafb.

Core Changes:
- Document requirements for new atomic properties.
- Add drm_gem_fb_(begin/end)_cpu_access helpers, and use them in some drivers.
- Document drm_property_enum.value for bitfields.
- Add explicit _NO_ for MIPI_DSI flags that disable features.
- Assorted documentation fixes.
- Update fb_damage handling, and move drm_plane_enable_fb_damage_clips to core.
- Add logging and docs to RMFB ioctl.
- Assorted small fixes to dp_mst, master handling.
- Clarify drm lease usage.

Driver Changes:
- Assorted small fixes to panfrost, hibmc, bridge/nwl-dsi, rockchip, vc4.
- More drm -> linux irq conversions.
- Add support for some Logic Technologies and Multi-Inno panels.
- Expose phy-functionality for drm/rockchip, to allow controlling from the media subsystem.
- Add support for 2 AUO panels.
- Add damage handling to ssd1307fb.
- Improve FIFO handling on mxsfb.
- Assorted small fixes to vmwgfx, and bump version to 2.19 for the new ioctls.
- Improve sony acx424akp backlight handling.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a753221a-e23e-0dc4-7ca6-8c1b179738d0@linux.intel.com

Merge tag 'du-next-20210728' of git://linuxtv.org/pinchartl/media into drm-next

- R-Car DU shutdown fixes
- R-Car DU conversion to bridge connector helper
- Misc small fixes

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YQGHjOSOw2G4+A3x@pendragon.ideasonboard.com

drm/vc4: hdmi: Remove unused struct

Commit 91e99e113929 ("drm/vc4: hdmi: Register HDMI codec") removed the
references to the vc4_hdmi_audio_component_drv structure, but not the
structure itself resulting in a warning. Remove it.

Fixes: 91e99e113929 ("drm/vc4: hdmi: Register HDMI codec")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707093632.1468127-2-maxime@cerno.tech

drm/vc4: hdmi: Remove redundant variables

The vc4_hdmi_audio_prepare function and the functions it's calling have
in several occurences multiple dereferences of either the sample rate or
the number of channels.

It turns out that these variables are also passed through the hdmi codec
parameters structure. Convert all the users to use this structure, and
if it's used multiple times use a variable to store it instead of
dereferencing it every time.

Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707093632.1468127-1-maxime@cerno.tech

drm: clarify usage of drm leases

We make the following changes to the documentation of drm leases to
make it easier to reason about their usage. In particular, we clarify
the lifetime and locking rules of lease fields in drm_master:

1. Make it clear that &drm_device.mode_config.idr_mutex protects the
lease idr and list structures for drm_master. The lessor field itself
doesn't need to be protected as it doesn't change after it's set in
drm_lease_create.

2. Add descriptions for the lifetime of lessors and leases.

3. Add an overview DOC: section in drm-uapi.rst that defines the
terminology for drm leasing, and explains how leases work and why
they're used.

Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210728102739.441543-1-desmondcheongzx@gmail.com

drm/amd/pm: Fix a bug in semaphore double-lock

Fix a bug in smu_cmn_send_msg_without_waiting() in
that this function does not need to take the
smu->message_lock mutex in order to send a message
down to the SMU. The mutex is acquired by the
caller of this function instead.

Cc: Alex Deucher <Alexander.Deucher@amd.com>
Cc: Changfeng Zhu <Changfeng.Zhu@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Fixes: 5810323ba69289 ("drm/amd/pm: Fix a bug communicating with the SMU (v5)")
Signed-off-by: Luben Tuikov <luben.tuikov@amd.com>
Reviewed-by: Alex Deucher <Alexander.Deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: enable psp front door loading by default for cyan_skillfish2

The function is ready on psp firmware, and enable it by default.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: adjust fence driver enable sequence

Fence driver was enabled per ring when sw init on per IP block before.
Change to enable all the fence driver at the same time after
amdgpu_device_ip_init finished.
Rename some function related to fence to make it reasonable for read.

Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Added PSP13 BL loading support for additional drivers

Added BL loading support for soc/intf/dbg drivers

Signed-off-by: John Clements <john.clements@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Consolidated PSP13 BL FW loading

Remove duplicate code

Signed-off-by: John Clements <john.clements@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Added support for added psp driver binaries FW

Detect psp driver binaries packed into FW and try to load the FW

Signed-off-by: John Clements <john.clements@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Added latest PSP FW header

Improved handling for scalling PSP FW binaries

Signed-off-by: John Clements <john.clements@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: remove the access of xxx_PSP_DEBUG on cycan_skillfish

It won't need to clear the xxx_PSP_DEBUG registers, because firmware
will handle this change.

Signed-off-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: add support for multiple backlights

On platforms that support multiple backlights, register
each one separately.  This lets us manage them independently
rather than registering a single backlight and applying the
same settings to both.

v2: fix typo:
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/panel-sony-acx424akp: Modernize backlight handling

This converts the internal backlight in the Sony ACX424AKP
driver to do it the canonical way:

- Assign the panel->backlight during probe.
- Let the panel framework handle the backlight.
- Make the backlight .set_brightness() turn the backlight
  off completely if blank.
- Fix some dev_err_probe() use cases along the way.

Tested on the U8500 HREF520 reference design.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715092808.1100106-1-linus.walleij@linaro.org

drm: use the lookup lock in drm_is_current_master

Inside drm_is_current_master, using the outer drm_device.master_mutex
to protect reads of drm_file.master makes the function prone to creating
lock hierarchy inversions. Instead, we can use the
drm_file.master_lookup_lock that sits at the bottom of the lock
hierarchy.

Reported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Desmond Cheong Zhi Xi <desmondcheongzx@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210724111824.59266-2-desmondcheongzx@gmail.com

maintainers: add bugs and chat URLs for amdgpu

Add links to the issue tracker and the IRC channel for the amdgpu
driver.

Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Pan Xinhui <Xinhui.Pan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu/display: only enable aux backlight control for OLED panels

We've gotten a number of reports about backlight control not
working on panels which indicate that they use aux backlight
control.  A recent patch:

commit 2d73eabe2984a435737498ab39bb1500a9ffe9a9
Author: Camille Cho <Camille.Cho@amd.com>
Date:   Thu Jul 8 18:28:37 2021 +0800

    drm/amd/display: Only set default brightness for OLED

    [Why]
    We used to unconditionally set backlight path as AUX for panels capable
    of backlight adjustment via DPCD in set default brightness.

    [How]
    This should be limited to OLED panel only since we control backlight via
    PWM path for SDR mode in LCD HDR panel.

Reviewed-by: Krunoslav Kovac <krunoslav.kovac@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Camille Cho <Camille.Cho@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Changes some other code to only use aux for backlight control on
OLED panels.  The commit message seems to indicate that PWM should
be used for SDR mode on HDR panels.  Do something similar for
backlight control in general.  This may need to be revisited if and
when HDR started to get used.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1438
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=213715
Reviewed-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: restore user customized OD settings properly for Sienna Cichlid

Properly restore those committed and non-committed user customized OD
settings.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/pm: restore user customized OD settings properly for NV1x

The customized OD settings can be divided into two parts: those
committed ones and non-committed ones.
  - For those changes which had been fed to SMU before S3/S4/Runpm
    suspend kicked, they are committed changes. They should be properly
    restored and fed to SMU on S3/S4/Runpm resume.
  - For those non-committed changes, they are restored only without feeding
    to SMU.

Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "Revert "drm/amdkfd: Add memory sync before TLB flush on unmap""

This reverts commit 4bba567c8c35a9cbcd16fb4780a0c3dfd162e08e.

Revert reason: The issue has been resolved.

Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "Revert "drm/amdgpu: Fix warning of Function parameter or member not described""

This reverts commit 4e7b93ca52fb228b177168d436449c5671415a72.

Revert reason: The issue has been resolved.

Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "Revert "drm/amdkfd: Make TLB flush conditional on mapping""

This reverts commit 7ed9876c9793bfe96fed58ba645d6c8e32f26001.

Revert reason: The issue has been resolved.

Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "Revert "drm/amdgpu: Add table_freed parameter to amdgpu_vm_bo_update""

This reverts commit 024d8811c90ed56d8b90cdcf71e51c9fedeff460.

Revert reason: The issue has been resolved.

Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Revert "Revert "drm/amdkfd: Add heavy-weight TLB flush after unmapping""

This reverts commit 430f8e6edbaac8abfddf76f1aef732d9c6257211.

Revert reason: Issue has been resolved.

Signed-off-by: Eric Huang <jinhuieric.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: 3.2.146

This version brings along following fixed:
  - Guard DST_Y_PREFETCH register overflow in DCN21
  - Add missing DCN21 IP parameter
  - Fix PSR command version
  - Add ETW logging for AUX failures
  - Add ETW log to dmub_psr_get_state
  - Fixed EdidUtility build errors
  - Fix missing reg offset for the dmcub test debug registers
  - Adding update authentication interface
  - Remove unused functions of opm state query support
  - Always wait for update lock status
  - Refactor riommu invalidation wa
  - Ensure dentist display clock update finished in DCN20

Reviewed-by: Hsieh Mike <Mike.Hsieh@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: [FW Promotion] Release 0.0.76

Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: ensure dentist display clock update finished in DCN20

[Why]
We don't check DENTIST_DISPCLK_CHG_DONE to ensure dentist
display clockis updated to target value. In some scenarios with large
display clock margin, it will deliver unfinished display clock and cause
issues like display black screen.

[How]
Checking DENTIST_DISPCLK_CHG_DONE to ensure display clock
has been update to target value before driver do other clock related
actions.

Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: refactor riommu invalidation wa

[Why]
A cleaner solution, only done once on boot.

[How]
Remove previous workaround and configure an extra
vmid one time on boot

Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Always wait for update lock status

Remove code that would skip wait for lock status for Diags
FPGA case

Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: remove unused functions

[why]
It has been decided that opm state query support will be dropped.
Therefore link encryption enabled and save current encryption states
won't be used anymore and there are no foreseeable usages in the future.
We will remove these two interfaces for clean up.

Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: add update authentication interface

[why]
Previously to toggle authentication, we need to remove and
add the same display back with modified adjustment.
This method will toggle DTM state without actual hardware changes.
This is not per design and would cause potential issues in the long run.

[how]
We are creating a dedicated interface that does the same thing as
remove and add back the display without changing DTM state.

Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: fix missing reg offset

[Why]
Initializing was missing reg offsets for the dmcub test debug registers
causing assert

[How]
Add initialization

Reviewed-by: Kazlauskas Nicholas <Nicholas.Kazlauskas@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fixed EdidUtility build errors

[HOW]
Added #ifdefs and refactored various parts of dc to
allow dc_link to be built by AMD EDID UTILITY

[WHY]
dc_dsc was refactored moving some of the code that AMD EDID UTILITY needed
to dc_link, so now dc_link needs to be included by AMD EDID UTILITY

Squash in DCN config fix (Alex)

Reviewed-by: Leung Martin <Martin.Leung@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Mark Morra <MarkAlbert.Morra@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/vmwgfx: Use 2.19 version number to recognize mks-stats ioctls

To let the userspace recognize that it's running on top of a vmwgfx
that supports mks-stat ioctls we need to bump the version number.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Reviewed-by: Neha Bhende <bhenden@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723165153.113198-4-zackr@vmware.com

drm/vmwgfx: Be a lot more flexible with MOB limits

The code was trying to keep a strict limit on the amount of mob
memory that was used in the guest by making it match the host
settings. There's technically no reason to do that (guests can
certainly use more than the host can have resident in renderers
at the same time).

In particular this is problematic because our userspace is not
great at handling OOM conditions and running out of MOB space
results in GL apps crashing, e.g. gnome-shell likes to allocate
huge surfaces (~61MB for the desktop on 2560x1600 with two workspaces)
and running out of memory there means that the gnome-shell crashes
on startup taking us back to the login and resulting in a system
where one can not login in graphically anymore.

Instead of letting the userspace crash we can extend available
MOB space, we just don't want to use all of the RAM for graphics,
so we're going to limit it to half of RAM.

With the addition of some extra logging this should make the
"guest has been configured with not enough graphics memory"
errors a lot easier to diagnose in cases where the automatic
expansion of MOB space fails.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723165153.113198-3-zackr@vmware.com

drm/vmwgfx: Cleanup logging

The code was using the old DRM logging functions, which made it
hard to figure out what was coming from vmwgfx. The newer logging
helpers include the driver name in the logs and make it explicit
which driver they're coming from. This allows us to standardize
our logging a bit and clean it up in the process.

vmwgfx is a little special because technically the hardware it's
running on can be anything from the last 12 years or so which is
why we need to include capabilities in the logs in the first
place or otherwise we'd have no way of knowing what were
the capabilities of the platform the guest was running in.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723165153.113198-2-zackr@vmware.com

drm/vmwgfx: Switch to using DRM_IOCTL_DEF_DRV

The macro has been accounting for DRM_COMMAND_BASE for a long time
now so there's no reason to still be duplicating it. Plus we were
leaving the name undefined which meant that all the DRM ioctl
warnings/errors were always listing "null" ioctl at the culprit.

This fixes the undefined ioctl name and removes duplicated code.

Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723165153.113198-1-zackr@vmware.com

drm/msm/gem: Mark active before pinning

Mark all the bos in the submit as active, before pinning, to prevent
evicting a buffer in the same submit to make room for a buffer earlier
in the table.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210728010632.2633470-14-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Utilize gpu scheduler priorities

The drm/scheduler provides additional prioritization on top of that
provided by however many number of ringbuffers (each with their own
priority level) is supported on a given generation.  Expose the
additional levels of priority to userspace and map the userspace
priority back to ring (first level of priority) and schedular priority
(additional priority levels within the ring).

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-13-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Drop struct_mutex in submit path

It is sufficient to serialize on the submit queue now.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-12-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Drop submit bo_list

This was only used to detect userspace including the same bo multiple
times in a submit.  But ww_mutex can already tell us this.

When we drop struct_mutex around the submit ioctl, we'd otherwise need
to lock the bo before adding it to the bo_list.  But since ww_mutex can
already tell us this, it is simpler just to remove the bo_list.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210728010632.2633470-11-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Conversion to drm scheduler

For existing adrenos, there is one or more ringbuffer, depending on
whether preemption is supported.  When preemption is supported, each
ringbuffer has it's own priority.  A submitqueue (which maps to a
gl context or vk queue in userspace) is mapped to a specific ring-
buffer at creation time, based on the submitqueue's priority.

Each ringbuffer has it's own drm_gpu_scheduler.  Each submitqueue
maps to a drm_sched_entity.  And each submit maps to a drm_sched_job.

Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/4
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-10-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm: rcar-du: lvds: Use dev_err_probe()

Simplify error handling by using the dev_err_probe() function.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: lvds: Don't set bridge driver_private field

The drm_bridge.driver_private field is set but never used. Don't set it.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Use drm_bridge_connector_init() helper

Use the drm_bridge_connector_init() helper to create a drm_connector for
each output, instead of relying on the bridge drivers doing so. Attach
the bridges with the DRM_BRIDGE_ATTACH_NO_CONNECTOR flag to instruct
them not to create a connector.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: dw-hdmi: Set output port number

Report the DT output port number in dw_hdmi_plat_data to connect to the
next bridge in the dw-hdmi driver.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: lvds: Convert to DRM panel bridge helper

Replace the manual panel handling with usage of the DRM panel bridge
helper. This simplifies the driver, and brings support for
DRM_BRIDGE_ATTACH_NO_CONNECTOR as an added bonus.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: bridge: dw-hdmi: Attach to next bridge if available

On all platforms except i.MX and Rockchip, the dw-hdmi DT bindings
require a video output port connected to an HDMI sink (most likely an
HDMI connector, in rare cases another bridges converting HDMI to another
protocol). For those platforms, retrieve the next bridge and attach it
from the dw-hdmi bridge attach handler.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com> # On V3U
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm/bridge: Centralize error message when bridge attach fails

Being informed of a failure to attach a bridge is useful, and many
drivers prints an error message in that case. Move the message to
drm_bridge_attach() to avoid code duplication.

Suggested-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Jyri Sarha <jyri.sarha@iki.fi>

drm: rcar-du: Shutdown the display on remove

When the device is unbound from the driver (the DU being a platform
device, this occurs either when removing the DU module, or when
unbinding the device manually through sysfs), the display may be active.
Make sure it gets shut down.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Don't put reference to drm_device in rcar_du_remove()

The reference to the drm_device that was acquired by
devm_drm_dev_alloc() is released automatically by the devres
infrastructure. It must not be released manually, as that causes a
reference underflow..

Fixes: ea6aae151887 ("drm: rcar-du: Embed drm_device in rcar_du_device")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm: rcar-du: Shutdown the display on system shutdown

When the system shuts down or warm reboots, the display may be active,
with the hardware accessing system memory. Upon reboot, the DDR will not
be accessible, which may cause issues.

Implement the platform_driver .shutdown() operation and shut down the
display to fix this.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>

drm/bridge: make a const array static, makes object smaller

Don't populate the const array frs_limits on the stack but instead make
it static. Makes the object code smaller by 128 bytes:

Before:
   text    data     bss     dec     hex filename
  24845    7440      64   32349    7e5d ./drivers/gpu/drm/bridge/tc358768.o

After:
   text    data     bss     dec     hex filename
  24749    7408      64   32221    7ddd ./drivers/gpu/drm/bridge/tc358768.o

(gcc version 10.2.0)

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>

drm/msm: Return ERR_PTR() from submit_create()

In the next patch, we start having more than a single potential failure
reason.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-9-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Track "seqno" fences by idr

Previously the (non-fd) fence returned from submit ioctl was a raw
seqno, which is scoped to the ring.  But from UABI standpoint, the
ioctls related to seqno fences all specify a submitqueue.  We can
take advantage of that to replace the seqno fences with a cyclic idr
handle.

This is in preperation for moving to drm scheduler, at which point
the submit ioctl will return after queuing the submit job to the
scheduler, but before the submit is written into the ring (and
therefore before a ring seqno has been assigned).  Which means we
need to replace the dma_fence that userspace may need to wait on
with a scheduler fence.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-8-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Consolidate submit bo state

Move all the locked/active/pinned state handling to msm_gem_submit.c.
In particular, for drm/scheduler, we'll need to do all this before
pushing the submit job to the scheduler.  But while we're at it we can
get rid of the dupicate pin and refcnt.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-7-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm/submit: Simplify out-fence-fd handling

No need for this to be split in two parts.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-6-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm: Drop drm_gem_object_put_locked()

Now that no one is using it, remove it.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20210728010632.2633470-5-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: drop drm_gem_object_put_locked()

No idea why we were still using this.  It certainly hasn't been needed
for some time.  So drop the pointless twin codepaths.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Small submitqueue creation cleanup

If we don't have a gpu, there is no need to create a submitqueue, which
lets us simplify the error handling and submitqueue creation.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Docs and misc cleanup

Fix a couple incorrect or misspelt comments, and add submitqueue doc
comment.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20210728010632.2633470-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Devfreq tuning

This adds a few things to try and make frequency scaling better match
the workload:

1) Longer polling interval to avoid whip-lashing between too-high and
   too-low frequencies in certain workloads, like mobile games which
   throttle themselves to 30fps.

   Previously our polling interval was short enough to let things
   ramp down to minimum freq in the "off" frame, but long enough to
   not react quickly enough when rendering started on the next frame,
   leading to uneven frame times.  (Ie. rather than a consistent 33ms
   it would alternate between 16/33/48ms.)

2) Awareness of when the GPU is active vs idle.  Since we know when
   the GPU is active vs idle, we can clamp the frequency down to the
   minimum while it is idle.  (If it is idle for long enough, then
   the autosuspend delay will eventually kick in and power down the
   GPU.)

   Since devfreq has no knowledge of powered-but-idle, this takes a
   small bit of trickery to maintain a "fake" frequency while idle.
   This, combined with the longer polling period allows devfreq to
   arrive at a reasonable "active" frequency, while still clamping
   to minimum freq when idle to reduce power draw.

3) Boost.  Because simple_ondemand needs to see a certain threshold
   of busyness to ramp up, we could end up needing multiple polling
   cycles before it reacts appropriately on interactive workloads
   (ex. scrolling a web page after reading for some time), on top
   of the already lengthened polling interval, when we see a idle
   to active transition after a period of idle time we boost the
   frequency that we return to.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210726144653.2180096-4-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Split out get_freq() helper

In the next patch, it grows a bit more, so lets not duplicate the logic
in multiple places.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210726144653.2180096-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Split out devfreq handling

Before we start adding more cleverness, split it into it's own file.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210726144653.2180096-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Signal fences sooner

Nothing we do to in update_fences() can't be done in an atomic context,
so move this into the GPU's irq context to reduce latency (and call
dma_fence_signal() so we aren't relying on dma_fence_is_signaled() which
would defeat the purpose).

Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210726144359.2179302-3-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/msm: Let fences read directly from memptrs

Let dma_fence::signaled, etc, read directly from the address that the hw
is writing with updated completed fence seqno, so we can potentially
notice that the fence is signaled sooner.

Plus add some docs.

Signed-off-by: Rob Clark <robdclark@chromium.org>
Link: https://lore.kernel.org/r/20210726144359.2179302-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>

drm/dp_mst: Fix return code on sideband message failure

Commit 2f015ec6eab6 ("drm/dp_mst: Add sideband down request tracing +
selftests") added some debug code for sideband message tracing. But
it seems to have unintentionally changed the behavior on sideband message
failure. It catches and returns failure only if DRM_UT_DP is enabled.
Otherwise it ignores the error code and returns success. So on an MST
unplug, the caller is unaware that the clear payload message failed and
ends up waiting for 4 seconds for the response. Fixes the issue by
returning the proper error code.

Changes in V2:
-- Revise commit text as review comment
-- add Fixes text

Changes in V3:
-- remove "unlikely" optimization

Fixes: 2f015ec6eab6 ("drm/dp_mst: Add sideband down request tracing + selftests")
Cc: <stable@vger.kernel.org> # v5.5+
Signed-off-by: Rajkumar Subbiah <rsubbia@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1625585434-9562-1-git-send-email-khsieh@codeaurora.org

drm: mxsfb: Clear FIFO_CLEAR bit

Make sure the FIFO_CLEAR bit is latched in when configuring the
controller, so that the FIFO is really cleared. And then clear
the FIFO_CLEAR bit, since it is not self-clearing.

Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # i.Core MX8MM
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224946.189524-1-marex@denx.de

drm: mxsfb: Use bus_format from the nearest bridge if present

In case there is a bridge connected to the LCDIF, use bus_format
from the bridge, otherwise behave as before and use bus_format
from the connector. This way, even if there are multiple bridges
in the display pipeline, the LCDIF will use the correct format.

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210726194457.341696-1-marex@denx.de

drm: mxsfb: Increase number of outstanding requests on V4 and newer HW

In case the DRAM is under high load, the MXSFB FIFO might underflow
and that causes visible artifacts. This could be triggered on i.MX8MM
using e.g. "$ memtester 128M" on a device with 1920x1080 panel. The
first "Stuck Address" test of the memtester will completely corrupt
the image on the panel and leave the MXSFB FIFO in odd state.

To avoid this underflow, increase number of outstanding requests to
DRAM from 2 to 16, which is the maximum. This mitigates the issue
and it can no longer be triggered.

Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224759.189351-1-marex@denx.de

drm: mxsfb: Enable recovery on underflow

There is some sort of corner case behavior of the controller,
which could rarely be triggered at least on i.MX6SX connected
to 800x480 DPI panel and i.MX8MM connected to DPI->DSI->LVDS
bridged 1920x1080 panel (and likely on other setups too), where
the image on the panel shifts to the right and wraps around.
This happens either when the controller is enabled on boot or
even later during run time. The condition does not correct
itself automatically, i.e. the display image remains shifted.

It seems this problem is known and is due to sporadic underflows
of the LCDIF FIFO. While the LCDIF IP does have underflow/overflow
IRQs, neither of the IRQs trigger and neither IRQ status bit is
asserted when this condition occurs.

All known revisions of the LCDIF IP have CTRL1 RECOVER_ON_UNDERFLOW
bit, which is described in the reference manual since i.MX23 as
"
  Set this bit to enable the LCDIF block to recover in the next
  field/frame if there was an underflow in the current field/frame.
"
Enable this bit to mitigate the sporadic underflows.

Fixes: 45d59d704080 ("drm: Add new driver for MXSFB controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Abrecht <public@danielabrecht.ch>
Cc: Emil Velikov <emil.l.velikov@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Agner <stefan@agner.ch>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210620224701.189289-1-marex@denx.de

drm/amd/display: Add ETW log to dmub_psr_get_state

[Why]
GPINT commands have the lowest priority in DMCUB, so it's possible
that the command isn't processed in time.

[How]
Add a log to help identify this case.

Reviewed-by: Koo Anthony <Anthony.Koo@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add ETW logging for AUX failures

[Why]
Would like to identify the cause of AUX transactions failing
via ETW logs.

[How]
Add ETW logging for AUX failures.

Reviewed-by: Pavic Josip <Josip.Pavic@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Fix PSR command version

[why]
For dual eDP when setting the new settings we need to set
command version to DMUB_CMD_PSR_CONTROL_VERSION_1, otherwise
DMUB will not read panel_inst parameter.
[how]
Instead of PSR_VERSION_1 pass DMUB_CMD_PSR_CONTROL_VERSION_1

Reviewed-by: Wood Wyatt <Wyatt.Wood@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Add missing DCN21 IP parameter

[why]
IP parameter min_meta_chunk_size_bytes is read for bandwidth
calculations but it was never defined.

[how]
Define min_meta_chunk_size_bytes and initialize value to 256.

Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Rename amdgpu_acpi_is_s0ix_supported

Rename amdgpu_acpi_is_s0ix_supported to better explain
functionality by renaming to amdgpu_acpi_is_s0ix_active

Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amd/display: Guard DST_Y_PREFETCH register overflow in DCN21

[why]
DST_Y_PREFETCH can overflow when DestinationLinesForPrefetch values are
too large due to the former being limited to 8 bits.

[how]
Set the maximum value of DestinationLinesForPrefetch to be 255 * refclk
period.

Reviewed-by: Laktyushkin Dmytro <dmytro.laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/amdgpu: Check pmops for desired suspend state

[Why]
User might change the suspend behaviour from OS.

[How]
Check with pm for target suspend state and set s0ix
flag only for s2idle state.

v2: User might change default suspend state, use target state
v3: squash in build fix

Suggested-by: Lijo Lazar <Lijo.Lazar@amd.com>
Signed-off-by: Pratik Vishwakarma <Pratik.Vishwakarma@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

video: fbdev: ssd1307fb: Cache address ranges

Cache the column and page ranges, to avoid doing unneeded I2C transfers
when the values haven't changed.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134730.3765898-6-geert@linux-m68k.org

video: fbdev: ssd1307fb: Optimize screen updates

Currently, each screen update triggers an I2C transfer of all screen
data, up to 1 KiB of data for a 128x64 display, which takes at least 20
ms in Fast mode.

Reduce the amount of transferred data by only updating the rectangle
that changed.  Remove the calls to ssd1307fb_set_col_range() and
ssd1307fb_set_page_range() during initialization, as
ssd1307fb_update_rect() now takes care of that.

Note that for now the optimized operation is only used for fillrect,
copyarea, and imageblit, which are used by fbcon.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134730.3765898-5-geert@linux-m68k.org

video: fbdev: ssd1307fb: Extract ssd1307fb_set_{col,page}_range()

Extract the code to set the column and page ranges into two helper
functions.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134730.3765898-4-geert@linux-m68k.org

video: fbdev: ssd1307fb: Simplify ssd1307fb_update_display()

Simplify the nested loops to handle conversion from linear frame buffer
to ssd1307 page layout:
  1. Move last page handling one level up, as the value of "m" is the
     same inside a page,
  2. array->data[] is filled linearly, so there is no need to
     recalculate array_idx over and over again; a simple increment is
     sufficient.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134730.3765898-3-geert@linux-m68k.org

video: fbdev: ssd1307fb: Propagate errors via ssd1307fb_update_display()

Make ssd1307fb_update_display() return an error code, so callers that
can handle failures can propagate it.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727134730.3765898-2-geert@linux-m68k.org

drm: document DRM_IOCTL_MODE_RMFB

Since there's no struct to attach the docs to, document the IOCTL
definition.

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Leandro Ribeiro <leandro.ribeiro@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ephVkof3uGu2RpOdBbrHE3qF98zBfIBRzXe4Vyoboh0@cp4-web-034.plabs.ch

drm: add logging for RMFB ioctl

We already have logging for ADDFB2. Add some logging for RMFB as
well.

This can be handy when trying to find out why a CRTC gets magically
disabled.

v2: make log message more explicit, add log messages to
drm_framebuffer_remove (Daniel)

Signed-off-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Pekka Paalanen <pekka.paalanen@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/EghsoRDcn1SJV0nxVqRCisPd7v0627yLZbBjn4A8Yg@cp3-web-048.plabs.ch

Backmerge remote-tracking branch 'drm/drm-next' into drm-misc-next

Required bump from v5.13-rc3 to v5.14-rc3, and to pick up sysfb compilation fixes.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>

drm/plane: Move drm_plane_enable_fb_damage_clips into core

We're trying to have a fairly strict split between core functionality
that defines the uapi, including the docs, and the helper functions to
implement it.

Move drm_plane_enable_fb_damage_clips and associated kerneldoc into
drm_plane from drm_damage_helper.c to fix this.

Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-3-daniel.vetter@ffwll.ch

drm/plane: check that fb_damage is set up when used

There's two stages of manual upload/invalidate displays:
- just handling dirtyfb and uploading the entire fb all the time
- looking at damage clips

In the latter case we support it through fbdev emulation (with
fb_defio), atomic property, and with the dirtfy clip rects.

Make sure at least the atomic property is set up as the main official
interface for this. Ideally we'd also check that
drm_atomic_helper_dirtyfb() is used and that fbdev defio is set up,
but that's quite a bit harder to do. Ideas very much welcome.

From a cursor audit drivers seem to be getting this right mostly, but
better to make sure. At least no one is bypassing the accessor
function.

v2:
- use drm_warn_once with a meaningful warning string (José)
- don't splat in the atomic check code for everyone (intel-gfx-ci)

Reviewed-by: José Roberto de Souza <jose.souza@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-2-daniel.vetter@ffwll.ch

drm/plane: remove drm_helper_get_plane_damage_clips

It's not used. Drivers should instead use the helpers anyway.

Currently both vbox and i915 hand-roll this and it's not the greatest.
vbox looks buggy, and i915 does a bit much that helpers would take
care of I think.

Also improve the kerneldocs while we're at it.

Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723083457.696939-1-daniel.vetter@ffwll.ch

drm/prime: fix comment on PRIME Helpers

s/Exporting/Importing

Fixes: 805dc614d58a8 ("drm/prime: Update docs")
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Jose Maria Casanova Crespo <jmcasanova@igalia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210723123307.31064-1-jmcasanova@igalia.com

drm/bridge: dw-mipi-dsi: Find the possible DSI devices

Finding panel_or_bridge might vary based on associated
DSI devices like DSI panel, bridge, and I2C based DSI
bridge.

1. DSI panels and bridges will invoke the host attach
   from probe in order to find the panel_or_bridge.

   chipone_probe()
       dw_mipi_dsi_host_attach().start
   dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...

   ltdc_encoder_init().start
       dw_mipi_dsi_bridge_attach().start
   dw_mipi_dsi_host_attach().start
       chipone_attach(). start

               chipone_attach(). done
   dw_mipi_dsi_host_attach().done
       dw_mipi_dsi_bridge_attach(). done
   ltdc_encoder_init().done

2. I2C based DSI bridge will invoke the drm_bridge_attach
   from bridge attach in order to find the panel_or_bridge.

   ltdc_encoder_init().start
       dw_mipi_dsi_bridge_attach().start
   dw_mipi_dsi_panel_or_bridge()
...found the panel_or_bridge...
   dw_mipi_dsi_host_attach().start
       sn65dsi83_attach(). start

               sn65dsi83_attach(). done
   dw_mipi_dsi_host_attach().done
       dw_mipi_dsi_bridge_attach(). done
   ltdc_encoder_init().done

So, invoke the panel_or_bridge from host attach and
bridge attach in order to find all possible DSI devices.

Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Yannick Fertre <yannick.fertre@foss.st.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210704140309.268469-1-jagan@amarulasolutions.com

efi: sysfb_efi: fix build when EFI is not set

When # CONFIG_EFI is not set, there are 2 definitions of
sysfb_apply_efi_quirks(). The stub from sysfb.h should be used
and the __init function from sysfb_efi.c should not be used.

../drivers/firmware/efi/sysfb_efi.c:337:13: error: redefinition of ‘sysfb_apply_efi_quirks’
 __init void sysfb_apply_efi_quirks(struct platform_device *pd)
             ^~~~~~~~~~~~~~~~~~~~~~
In file included from ../drivers/firmware/efi/sysfb_efi.c:26:0:
../include/linux/sysfb.h:65:20: note: previous definition of ‘sysfb_apply_efi_quirks’ was here
 static inline void sysfb_apply_efi_quirks(struct platform_device *pd)
                    ^~~~~~~~~~~~~~~~~~~~~~

Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Fixes: 8633ef82f101 ("drivers/firmware: consolidate EFI framebuffer setup for all arches")
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-next@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210727050447.7339-1-rdunlap@infradead.org