LI Qingwu [Thu, 26 May 2022 13:33:57 +0000 (13:33 +0000)]
iio: accel: bmi088: Add support for bmi085 accel
Add supports for BMI085, an Inertial Measurement Unit,
with an accelerometer and gyroscope.
The commit adds the accelerometer driver for the SPI interface.
The gyroscope part is already supported by the BMG160 driver.
Unlike BMI088, the BMI085 accelerometer ranges are +/-2, 4, 6,
and 8g, the scales are calculated as 9.8/32768*pow(2,reg41+1).
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Link: https://lore.kernel.org/r/20220526133359.2261928-5-Qing-wu.Li@leica-geosystems.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LI Qingwu [Thu, 26 May 2022 13:33:56 +0000 (13:33 +0000)]
iio: accel: bmi088: modified the device name
iio: accel: bmi088: modified the device name
It is possible to have multiple sensors connected on the same platform.
For support of different sensors, making it possible to obtain the
device name by reading the chip id. If the device was found in the
table but the device tree binding is different, the driver will carry
on with a warning. If no matching device was found, the driver load
the binding chip info.
Tested case, test with bmi085 and bmi090 patches applied:
connect 3 bmi090l to the system, and set device tree compatible:
spi2.0: compatible = "bosch,bmi090l-accel";
spi2.2: compatible = "bosch,bmi088-accel";
spi2.4: compatible = "bosch,bmi085-accel";
Get a warning for the mismatched devices:
bmi088_accel_spi spi2.2: unexpected chip id 0x1A
bmi088_accel_spi spi2.4: unexpected chip id 0x1A
Get the real present device name:
/sys/bus/iio/devices/iio:device1/name:bmi090l-accel
/sys/bus/iio/devices/iio:device3/name:bmi090l-accel
/sys/bus/iio/devices/iio:device5/name:bmi090l-accel
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Link: https://lore.kernel.org/r/20220526133359.2261928-4-Qing-wu.Li@leica-geosystems.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LI Qingwu [Thu, 26 May 2022 13:33:55 +0000 (13:33 +0000)]
iio: accel: bmi088: Make it possible to config scales
The sensor can set the scales by writing the range register 0x41,
The current driver has no interface to configure it.
The commit adds the interface for config the scales.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Link: https://lore.kernel.org/r/20220526133359.2261928-3-Qing-wu.Li@leica-geosystems.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
LI Qingwu [Thu, 26 May 2022 13:33:54 +0000 (13:33 +0000)]
iio: accel: bmi088: Modified the scale calculate
The units after application of scale are 100*m/s^2,
The scale calculation is only for the device
with the range of 3, 6, 12, and 24g,
but some other chips have a range of 2, 4, 6, and 8g.
Modified the scales from formula to a list, the scales in the list are
calculated as 9.8/32768*pow(2,reg41+1)*1.5, refer to datasheet 5.3.4.
The new units after the application of scale are m/s^2.
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Signed-off-by: LI Qingwu <Qing-wu.Li@leica-geosystems.com.cn>
Link: https://lore.kernel.org/r/20220526133359.2261928-2-Qing-wu.Li@leica-geosystems.com.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Tachici [Thu, 26 May 2022 13:46:02 +0000 (16:46 +0300)]
dt-bindings: iio: imu: adis16480: update maintainers
Update bindings maintainerns section.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20220526134603.75216-6-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Tachici [Thu, 26 May 2022 13:46:01 +0000 (16:46 +0300)]
dt-bindings: iio: dac: AD5770R: update maintainers
Update bindings maintainerns section.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20220526134603.75216-5-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Tachici [Thu, 26 May 2022 13:46:00 +0000 (16:46 +0300)]
dt-bindings: iio: adc: axi-adc: update maintainers
Update bindings maintainerns section.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20220526134603.75216-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Tachici [Thu, 26 May 2022 13:45:59 +0000 (16:45 +0300)]
dt-bindings: iio: adc: AD9467: update maintainers
Update bindings maintainerns section.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20220526134603.75216-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Alexandru Tachici [Thu, 26 May 2022 13:45:58 +0000 (16:45 +0300)]
dt-bindings: iio: accel: ADIS16240: update maintainers
Update bindings maintainerns section.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Acked-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20220526134603.75216-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Markuss Broks [Mon, 23 May 2022 17:53:43 +0000 (20:53 +0300)]
proximity: vl53l0x: Handle the reset GPIO
Handle the GPIO connected to the XSHUT/RST_N pin of VL53L0X.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220523175344.5845-5-markuss.broks@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Markuss Broks [Mon, 23 May 2022 17:53:42 +0000 (20:53 +0300)]
proximity: vl53l0x: Handle the VDD regulator
Handle the regulator supplying the VDD pin of VL53L0X.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220523175344.5845-4-markuss.broks@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Markuss Broks [Mon, 23 May 2022 17:53:41 +0000 (20:53 +0300)]
proximity: vl53l0x: Prefer pre-initialized interrupt flags
On some boards interrupt type might be different than falling edge,
like hardcoded in driver. Leave interrupt flags as they were pre-configured
from the device-tree. If they're not provided, default to falling edge
interrupts.
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220523175344.5845-3-markuss.broks@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Markuss Broks [Mon, 23 May 2022 17:53:40 +0000 (20:53 +0300)]
dt-bindings: proximity: vl53l0x: Document optional supply and GPIO properties
Add the optional properties for the VL53L0X ToF sensor to the
device-tree binding.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Markuss Broks <markuss.broks@gmail.com>
Link: https://lore.kernel.org/r/20220523175344.5845-2-markuss.broks@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Li Zhengyu [Mon, 23 May 2022 12:27:55 +0000 (20:27 +0800)]
iio: srf08: Remove redundant if statement
(!val) has been checked outside the loop, remove redundant (val &&)
from loop.
Signed-off-by: Li Zhengyu <lizhengyu3@huawei.com>
Acked-by: Andreas Klinger <ak@it-klinger.de>
Link: https://lore.kernel.org/r/20220523122755.90638-1-lizhengyu3@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Peter Rosin [Mon, 25 Apr 2022 20:47:08 +0000 (22:47 +0200)]
iio: dac: ti-dac5571: add support for ti,
dac121c081
It fits right in as a single 12-bit DAC.
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/a09a49a5-3d01-21f7-02ed-b191d70e7609@axentia.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Peter Rosin [Mon, 25 Apr 2022 20:46:58 +0000 (22:46 +0200)]
dt-bindings: iio: ti-dac5571: Add ti,
dac121c081
It works much the same as ti,dac7571, so it fits in the "family" even
if the name is a little bit different.
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/a230b7a8-4146-9483-48ee-0bebdd945731@axentia.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cosmin Tanislav [Sat, 14 May 2022 18:20:10 +0000 (21:20 +0300)]
iio: accel: adxl367: do not update FIFO watermark on scan mode update
Currently, the driver updates the FIFO watermark inside both
update_scan_mode() and hwfifo_set_watermark(). Inside the IIO core,
hwfifo_set_watermark() is called immediately after update_scan_mode(),
making the first call to set_fifo_samples() redundant.
Remove the first call to set_fifo_samples(), and merge the
set_fifo_samples() function into the set_fifo_watermark()
function. Also, since fifo_set_size is always set inside of
update_scan_mode(), and it cannot be set to 0, remove the
zero check from set_fifo_samples().
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220514182010.152784-1-cosmin.tanislav@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 14 May 2022 13:32:50 +0000 (15:32 +0200)]
iio:magnetometer:mbc150: Make bmc150_magn_remove() return void
bmc150_magn_remove() always returns zero. Make it return no value which
makes it easier to see in the callers that there is no error to handle.
Also the return value of i2c driver remove callbacks is ignored anyway.
This prepares making i2c remove callbacks return void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220514133250.307955-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Julia Lawall [Sat, 21 May 2022 11:11:18 +0000 (13:11 +0200)]
iio: chemical: bme680: fix typo in comment
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-68-Julia.Lawall@inria.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Julia Lawall [Sat, 21 May 2022 11:11:04 +0000 (13:11 +0200)]
iio: proximity: ping: fix typo in comment
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/20220521111145.81697-54-Julia.Lawall@inria.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:29 +0000 (17:59 +0200)]
iio:light:vcnl4035: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:28 +0000 (17:59 +0200)]
iio:light:vcnl4000: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:27 +0000 (17:59 +0200)]
iio:light:us5182d: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:26 +0000 (17:59 +0200)]
iio:light:pa12203001: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:25 +0000 (17:59 +0200)]
iio:chemical:ccs811: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:24 +0000 (17:59 +0200)]
iio:chemical:atlas: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:23 +0000 (17:59 +0200)]
iio:adc:ti-ads1015: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sun, 15 May 2022 15:59:22 +0000 (17:59 +0200)]
iio:adc:ina2xx: Improve error reporting for problems during .remove()
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Biju Das [Sun, 15 May 2022 06:03:36 +0000 (07:03 +0100)]
iio: adc: rzg2l_adc: Remove unnecessary channel check from rzg2l_adc_read_label()
Remove unnecessary channel check from rzg2l_adc_read_label(), as the
channel error handling is already done in probe(). Therefore no need to
validate at runtime.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220515060337.16513-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Biju Das [Sun, 15 May 2022 06:03:35 +0000 (07:03 +0100)]
dt-bindings: iio: adc: Document Renesas RZ/G2UL ADC
Document Renesas RZ/G2UL ADC bindings. RZ/G2UL ADC is almost identical
to RZ/G2L, but it has 2 analog input channels compared to 8 channels
on the RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220515060337.16513-2-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
William Breathitt Gray [Tue, 10 May 2022 17:31:00 +0000 (13:31 -0400)]
iio: dac: cio-dac: Utilize iomap interface
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/c973ce9a326131552caf762381edf8e90be43cc5.1652201921.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
William Breathitt Gray [Tue, 10 May 2022 17:30:59 +0000 (13:30 -0400)]
iio: adc: stx104: Utilize iomap interface
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/64673797df382c52fc32fce24348b25a0b05e73a.1652201921.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 14 May 2022 13:04:32 +0000 (15:04 +0200)]
iio: health: afe4404: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference.
As afe4404_remove() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220514130432.304674-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gwendal Grignou [Wed, 27 Apr 2022 19:08:04 +0000 (12:08 -0700)]
iio: common: cros_ec_sensors: Add label attribute
When sensor location is known, populate iio sysfs "label" attribute:
* "accel-base" : the sensor is in the base of the convertible (2-1)
device.
* "accel-display" : the sensor is in the lid/display plane of the
device.
* "accel-camera" : the sensor is in the swivel camera subassembly.
The non-standard |location| attribute is removed, the field |loc| in
cros_ec_sensors_core_state is removed.
It apply to standalone accelerometer as well as IMU (accelerometer +
gyroscope) and sensors where the location is known (light).
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20220427190804.961697-3-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Gwendal Grignou [Wed, 27 Apr 2022 19:08:03 +0000 (12:08 -0700)]
iio: ABI: Add a new location label
Add "accel-camera" when an IMU is location near the camera in a swivel
sub-assembly. These IMU are used for AR applications.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20220427190804.961697-2-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Sat, 7 May 2022 17:34:40 +0000 (20:34 +0300)]
iio: imu: st_lsm6dsx: Switch from of headers to mod_devicetable.h
There is nothing directly using of specific interfaces in this driver,
so lets not include the headers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220507173440.29053-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:19 +0000 (19:00 +0530)]
iio: accel: bma400: Add support for activity and inactivity events
Add support for activity and inactivity events for all axis based on the
threshold, duration and hysteresis value set from the userspace. INT1 pin
is used to interrupt and event is pushed to userspace.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-9-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:18 +0000 (19:00 +0530)]
iio: accel: bma400: Add activity recognition support
Add support for activity recognition like STILL, WALKING, RUNNING
and these events are pushed to the userspace whenever the STEP
interrupt occurs.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-8-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:17 +0000 (19:00 +0530)]
iio: accel: bma400: Add step change event
Added support for event when there is a detection of step change.
INT1 pin is used to interrupt and event is pushed to userspace.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-7-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:16 +0000 (19:00 +0530)]
iio: accel: bma400: Add separate channel for step counter
Added channel for step counter which can be enable or disable
through the sysfs interface.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-6-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:15 +0000 (19:00 +0530)]
iio: accel: bma400: Add triggered buffer support
Added trigger buffer support to read continuous acceleration
and temperature data from device with data ready interrupt which
is mapped to INT1 pin.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-5-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:14 +0000 (19:00 +0530)]
iio: accel: bma400: conversion to device-managed function
This is a conversion to device-managed by using devm_iio_device_register()
inside probe function. Previously the bma400 was not put into power down
mode in some error paths in probe where it now is, but that should cause
no harm.
The dev_set_drvdata() call, bma400_remove() function and hooks in the I2C
and SPI driver struct is removed as devm_iio_device_register() function is
used to automatically unregister on driver detach.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-4-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:13 +0000 (19:00 +0530)]
iio: accel: bma400: Reordering of header files
Reordering of header files and removing the iio/sysfs.h since
custom attributes are not being used in the driver.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-3-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Jagath Jog J [Thu, 5 May 2022 13:30:12 +0000 (19:00 +0530)]
iio: accel: bma400: Fix the scale min and max macro values
Changing the scale macro values to match the bma400 sensitivity
for 1 LSB of all the available ranges.
Fixes:
465c811f1f20 ("iio: accel: Add driver for the BMA400")
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220505133021.22362-2-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:07 +0000 (10:16 +0200)]
iio:light:tsl2583: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As tsl2583_set_power_state() already emits an error message on failure
and the additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-10-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:06 +0000 (10:16 +0200)]
iio:light:stk3310: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As stk3310_set_state() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:05 +0000 (10:16 +0200)]
iio:light:opt3001: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As opt3001_remove() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:04 +0000 (10:16 +0200)]
iio:light:jsa1212: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As jsa1212_power_off() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:03 +0000 (10:16 +0200)]
iio:light:isl29028: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As isl29028_clear_configure_ret() already emits an error message on
failure and the additional error message by the i2c core doesn't add any
useful information, change the return value to zero to suppress this
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:02 +0000 (10:16 +0200)]
iio:light:bh1780: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As bh1780_remove() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
While at it, add the error code to the remaining error message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220430081607.15078-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:01 +0000 (10:16 +0200)]
iio:accel:stk8ba50: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As stk8ba50_set_mode() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:16:00 +0000 (10:16 +0200)]
iio:accel:stk8312: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As stk8312_set_mode() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König [Sat, 30 Apr 2022 08:15:59 +0000 (10:15 +0200)]
iio:accel:mc3230: Remove duplicated error reporting in .remove()
Returning an error value in an i2c remove callback results in an error
message being emitted by the i2c core, but otherwise it doesn't make a
difference. The device goes away anyhow and the devm cleanups are
called.
As mc3230_set_opcon() already emits an error message on failure and the
additional error message by the i2c core doesn't add any useful
information, change the return value to zero to suppress this message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220430081607.15078-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Wed, 4 May 2022 11:35:57 +0000 (14:35 +0300)]
iio: proximity: srf04: Make use of device properties
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220504113557.59048-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Andy Shevchenko [Wed, 13 Apr 2022 18:56:56 +0000 (21:56 +0300)]
iio: trigger: stm32-lptimer-trigger: Make use of device properties
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220413185656.21994-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Linus Torvalds [Mon, 6 Jun 2022 00:18:54 +0000 (17:18 -0700)]
Linux 5.19-rc1
Linus Torvalds [Mon, 6 Jun 2022 00:14:03 +0000 (17:14 -0700)]
Merge tag 'pull-work.fd-fixes' of git://git./linux/kernel/git/viro/vfs
Pull file descriptor fix from Al Viro:
"Fix for breakage in #work.fd this window"
* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the breakage in close_fd_get_file() calling conventions change
Linus Torvalds [Mon, 6 Jun 2022 00:05:38 +0000 (17:05 -0700)]
Merge tag 'mm-hotfixes-stable-2022-06-05' of git://git./linux/kernel/git/akpm/mm
Pull mm hotfixes from Andrew Morton:
"Fixups for various recently-added and longer-term issues and a few
minor tweaks:
- fixes for material merged during this merge window
- cc:stable fixes for more longstanding issues
- minor mailmap and MAINTAINERS updates"
* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
x86/kexec: fix memory leak of elf header buffer
mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
MAINTAINERS: add maintainer information for z3fold
mailmap: update Josh Poimboeuf's email
Linus Torvalds [Sun, 5 Jun 2022 23:58:27 +0000 (16:58 -0700)]
Merge tag 'mm-nonmm-stable-2022-06-05' of git://git./linux/kernel/git/akpm/mm
Pull delay-accounting update from Andrew Morton:
"A single featurette for delay accounting.
Delayed a bit because, unusually, it had dependencies on both the
mm-stable and mm-nonmm-stable queues"
* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
delayacct: track delays from write-protect copy
Linus Torvalds [Sun, 5 Jun 2022 18:51:48 +0000 (11:51 -0700)]
bluetooth: don't use bitmaps for random flag accesses
The bluetooth code uses our bitmap infrastructure for the two bits (!)
of connection setup flags, and in the process causes odd problems when
it converts between a bitmap and just the regular values of said bits.
It's completely pointless to do things like bitmap_to_arr32() to convert
a bitmap into a u32. It shoudln't have been a bitmap in the first
place. The reason to use bitmaps is if you have arbitrary number of
bits you want to manage (not two!), or if you rely on the atomicity
guarantees of the bitmap setting and clearing.
The code could use an "atomic_t" and use "atomic_or/andnot()" to set and
clear the bit values, but considering that it then copies the bitmaps
around with "bitmap_to_arr32()" and friends, there clearly cannot be a
lot of atomicity requirements.
So just use a regular integer.
In the process, this avoids the warnings about erroneous use of
bitmap_from_u64() which were triggered on 32-bit architectures when
conversion from a u64 would access two words (and, surprise, surprise,
only one word is needed - and indeed overkill - for a 2-bit bitmap).
That was always problematic, but the compiler seems to notice it and
warn about the invalid pattern only after commit
0a97953fd221 ("lib: add
bitmap_{from,to}_arr64") changed the exact implementation details of
'bitmap_from_u64()', as reported by Sudip Mukherjee and Stephen Rothwell.
Fixes:
fe92ee6425a2 ("Bluetooth: hci_core: Rework hci_conn_params flags")
Link: https://lore.kernel.org/all/YpyJ9qTNHJzz0FHY@debian/
Link: https://lore.kernel.org/all/20220606080631.0c3014f2@canb.auug.org.au/
Link: https://lore.kernel.org/all/20220605162537.1604762-1-yury.norov@gmail.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Yury Norov <yury.norov@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Sun, 5 Jun 2022 18:01:42 +0000 (14:01 -0400)]
fix the breakage in close_fd_get_file() calling conventions change
It used to grab an extra reference to struct file rather than
just transferring to caller the one it had removed from descriptor
table. New variant doesn't, and callers need to be adjusted.
Reported-and-tested-by: syzbot+47dd250f527cb7bebf24@syzkaller.appspotmail.com
Fixes:
6319194ec57b ("Unify the primitives for file descriptor closing")
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 5 Jun 2022 18:00:43 +0000 (11:00 -0700)]
Merge tag 'x86-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 SGX fix from Thomas Gleixner:
"A single fix for x86/SGX to prevent that memory which is allocated for
an SGX enclave is accounted to the wrong memory control group"
* tag 'x86-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/sgx: Set active memcg prior to shmem allocation
Linus Torvalds [Sun, 5 Jun 2022 17:57:35 +0000 (10:57 -0700)]
Merge tag 'x86-mm-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 mm cleanup from Thomas Gleixner:
"Use PAGE_ALIGNED() instead of open coding it in the x86/mm code"
* tag 'x86-mm-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Use PAGE_ALIGNED(x) instead of IS_ALIGNED(x, PAGE_SIZE)
Linus Torvalds [Sun, 5 Jun 2022 17:55:23 +0000 (10:55 -0700)]
Merge tag 'x86-microcode-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 microcode updates from Thomas Gleixner:
- Disable late microcode loading by default. Unless the HW people get
their act together and provide a required minimum version in the
microcode header for making a halfways informed decision its just
lottery and broken.
- Warn and taint the kernel when microcode is loaded late
- Remove the old unused microcode loader interface
- Remove a redundant perf callback from the microcode loader
* tag 'x86-microcode-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode: Remove unnecessary perf callback
x86/microcode: Taint and warn on late loading
x86/microcode: Default-disable late loading
x86/microcode: Rip out the OLD_INTERFACE
Linus Torvalds [Sun, 5 Jun 2022 17:53:41 +0000 (10:53 -0700)]
Merge tag 'x86-cleanups-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 cleanups from Thomas Gleixner:
"A set of small x86 cleanups:
- Remove unused headers in the IDT code
- Kconfig indendation and comment fixes
- Fix all 'the the' typos in one go instead of waiting for bots to
fix one at a time"
* tag 'x86-cleanups-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Fix all occurences of the "the the" typo
x86/idt: Remove unused headers
x86/Kconfig: Fix indentation of arch/x86/Kconfig.debug
x86/Kconfig: Fix indentation and add endif comments to arch/x86/Kconfig
Linus Torvalds [Sun, 5 Jun 2022 17:49:42 +0000 (10:49 -0700)]
Merge tag 'x86-boot-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull x86 boot update from Thomas Gleixner:
"Use strlcpy() instead of strscpy() in arch_setup()"
* tag 'x86-boot-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/setup: Use strscpy() to replace deprecated strlcpy()
Linus Torvalds [Sun, 5 Jun 2022 17:47:06 +0000 (10:47 -0700)]
Merge tag 'timers-core-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull clockevent/clocksource updates from Thomas Gleixner:
- Device tree bindings for MT8186
- Tell the kernel that the RISC-V SBI timer stops in deeper power
states
- Make device tree parsing in sp804 more robust
- Dead code removal and tiny fixes here and there
- Add the missing SPDX identifiers
* tag 'timers-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/oxnas-rps: Fix irq_of_parse_and_map() return value
clocksource/drivers/timer-ti-dm: Remove unnecessary NULL check
clocksource/drivers/timer-sun5i: Convert to SPDX identifier
clocksource/drivers/timer-sun4i: Convert to SPDX identifier
clocksource/drivers/pistachio: Convert to SPDX identifier
clocksource/drivers/orion: Convert to SPDX identifier
clocksource/drivers/lpc32xx: Convert to SPDX identifier
clocksource/drivers/digicolor: Convert to SPDX identifier
clocksource/drivers/armada-370-xp: Convert to SPDX identifier
clocksource/drivers/mips-gic-timer: Convert to SPDX identifier
clocksource/drivers/jcore: Convert to SPDX identifier
clocksource/drivers/bcm_kona: Convert to SPDX identifier
clocksource/drivers/sp804: Avoid error on multiple instances
clocksource/drivers/riscv: Events are stopped during CPU suspend
clocksource/drivers/ixp4xx: Drop boardfile probe path
dt-bindings: timer: Add compatible for Mediatek MT8186
Linus Torvalds [Sun, 5 Jun 2022 17:42:40 +0000 (10:42 -0700)]
Merge tag 'sched-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"Fix the fallout of sysctl code move which placed the init function
wrong"
* tag 'sched-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/autogroup: Fix sysctl move
Linus Torvalds [Sun, 5 Jun 2022 17:40:31 +0000 (10:40 -0700)]
Merge tag 'perf-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull perf fixes from Thomas Gleixner:
- Make the ICL event constraints match reality
- Remove a unused local variable
* tag 'perf-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove unused local variable
perf/x86/intel: Fix event constraints for ICL
Linus Torvalds [Sun, 5 Jun 2022 17:39:20 +0000 (10:39 -0700)]
Merge tag 'perf-core-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull perf fixlet from Thomas Gleixner:
"Trivial indentation fix in Kconfig"
* tag 'perf-core-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/Kconfig: Fix indentation in the Kconfig file
Linus Torvalds [Sun, 5 Jun 2022 16:45:27 +0000 (09:45 -0700)]
Merge tag 'objtool-urgent-2022-06-05' of git://git./linux/kernel/git/tip/tip
Pull objtool fixes from Thomas Gleixner:
- Handle __ubsan_handle_builtin_unreachable() correctly and treat it as
noreturn
- Allow architectures to select uaccess validation
- Use the non-instrumented bit test for test_cpu_has() to prevent
escape from non-instrumentable regions
- Use arch_ prefixed atomics for JUMP_LABEL=n builds to prevent escape
from non-instrumentable regions
- Mark a few tiny inline as __always_inline to prevent GCC from
bringing them out of line and instrumenting them
- Mark the empty stub context_tracking_enabled() as always inline as
GCC brings them out of line and instruments the empty shell
- Annotate ex_handler_msr_mce() as dead end
* tag 'objtool-urgent-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/extable: Annotate ex_handler_msr_mce() as a dead end
context_tracking: Always inline empty stubs
x86: Always inline on_thread_stack() and current_top_of_stack()
jump_label,noinstr: Avoid instrumentation for JUMP_LABEL=n builds
x86/cpu: Elide KCSAN for cpu_has() and friends
objtool: Mark __ubsan_handle_builtin_unreachable() as noreturn
objtool: Add CONFIG_HAVE_UACCESS_VALIDATION
Linus Torvalds [Sun, 5 Jun 2022 16:25:12 +0000 (09:25 -0700)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"Mostly small bug fixes plus other trivial updates.
The major change of note is moving ufs out of scsi and a minor update
to lpfc vmid handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: qla2xxx: Remove unused 'ql_dm_tgt_ex_pct' parameter
scsi: qla2xxx: Remove setting of 'req' and 'rsp' parameters
scsi: mpi3mr: Fix kernel-doc
scsi: lpfc: Add support for ATTO Fibre Channel devices
scsi: core: Return BLK_STS_TRANSPORT for ALUA transitioning
scsi: sd_zbc: Prevent zone information memory leak
scsi: sd: Fix potential NULL pointer dereference
scsi: mpi3mr: Rework mrioc->bsg_device model to fix warnings
scsi: myrb: Fix up null pointer access on myrb_cleanup()
scsi: core: Unexport scsi_bus_type
scsi: sd: Don't call blk_cleanup_disk() in sd_probe()
scsi: ufs: ufshcd: Delete unnecessary NULL check
scsi: isci: Fix typo in comment
scsi: pmcraid: Fix typo in comment
scsi: smartpqi: Fix typo in comment
scsi: qedf: Fix typo in comment
scsi: esas2r: Fix typo in comment
scsi: storvsc: Fix typo in comment
scsi: ufs: Split the drivers/scsi/ufs directory
scsi: qla1280: Remove redundant variable
...
Linus Torvalds [Sun, 5 Jun 2022 16:12:28 +0000 (09:12 -0700)]
Merge tag 'hte/for-5.19-rc1' of git://git./linux/kernel/git/tegra/linux
Pull hardware timestamping subsystem from Thierry Reding:
"This contains the new HTE (hardware timestamping engine) subsystem
that has been in the works for a couple of months now.
The infrastructure provided allows for drivers to register as hardware
timestamp providers, while consumers will be able to request events
that they are interested in (such as GPIOs and IRQs) to be timestamped
by the hardware providers.
Note that this currently supports only one provider, but there seems
to be enough interest in this functionality and we expect to see more
drivers added once this is merged"
[ Linus Walleij mentions the Intel PMC in the Elkhart and Tiger Lake
platforms as another future timestamp provider ]
* tag 'hte/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: timestamp: Correct id path
dt-bindings: Renamed hte directory to timestamp
hte: Uninitialized variable in hte_ts_get()
hte: Fix off by one in hte_push_ts_ns()
hte: Fix possible use-after-free in tegra_hte_test_remove()
hte: Remove unused including <linux/version.h>
MAINTAINERS: Add HTE Subsystem
hte: Add Tegra HTE test driver
tools: gpio: Add new hardware clock type
gpiolib: cdev: Add hardware timestamp clock type
gpio: tegra186: Add HTE support
gpiolib: Add HTE support
dt-bindings: Add HTE bindings
hte: Add Tegra194 HTE kernel provider
drivers: Add hardware timestamp engine (HTE) subsystem
Documentation: Add HTE subsystem guide
Linus Torvalds [Sun, 5 Jun 2022 16:06:03 +0000 (09:06 -0700)]
Merge tag 'kbuild-v5.19-3' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- Fix build regressions for parisc, csky, nios2, openrisc
- Simplify module builds for CONFIG_LTO_CLANG and CONFIG_X86_KERNEL_IBT
- Remove arch/parisc/nm, which was presumably a workaround for old
tools
- Check the odd combination of EXPORT_SYMBOL and 'static' precisely
- Make external module builds robust against "too long argument error"
- Support j, k keys for moving the cursor in nconfig
* tag 'kbuild-v5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: Allow to select bash in a modified environment
scripts: kconfig: nconf: make nconfig accept jk keybindings
modpost: use fnmatch() to simplify match()
modpost: simplify mod->name allocation
kbuild: factor out the common objtool arguments
kbuild: move vmlinux.o link to scripts/Makefile.vmlinux_o
kbuild: clean .tmp_* pattern by make clean
kbuild: remove redundant cleanups in scripts/link-vmlinux.sh
kbuild: rebuild multi-object modules when objtool is updated
kbuild: add cmd_and_savecmd macro
kbuild: make *.mod rule robust against too long argument error
kbuild: make built-in.a rule robust against too long argument error
kbuild: check static EXPORT_SYMBOL* by script instead of modpost
parisc: remove arch/parisc/nm
kbuild: do not create *.prelink.o for Clang LTO or IBT
kbuild: replace $(linked-object) with CONFIG options
kbuild: do not try to parse *.cmd files for objects provided by compiler
kbuild: replace $(if A,A,B) with $(or A,B) in scripts/Makefile.modpost
modpost: squash if...else-if in find_elf_symbol2()
modpost: reuse ARRAY_SIZE() macro for section_mismatch()
...
Linus Torvalds [Sun, 5 Jun 2022 02:07:15 +0000 (19:07 -0700)]
Merge tag 'pull-18-rc1-work.namei' of git://git./linux/kernel/git/viro/vfs
Pull vfs pathname updates from Al Viro:
"Several cleanups in fs/namei.c"
* tag 'pull-18-rc1-work.namei' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
namei: cleanup double word in comment
get rid of dead code in legitimize_root()
fs/namei.c:reserve_stack(): tidy up the call of try_to_unlazy()
Linus Torvalds [Sun, 5 Jun 2022 02:00:05 +0000 (19:00 -0700)]
Merge tag 'pull-18-rc1-work.mount' of git://git./linux/kernel/git/viro/vfs
Pull mount handling updates from Al Viro:
"Cleanups (and one fix) around struct mount handling.
The fix is usermode_driver.c one - once you've done kern_mount(), you
must kern_unmount(); simple mntput() will end up with a leak. Several
failure exits in there messed up that way... In practice you won't hit
those particular failure exits without fault injection, though"
* tag 'pull-18-rc1-work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
move mount-related externs from fs.h to mount.h
blob_to_mnt(): kern_unmount() is needed to undo kern_mount()
m->mnt_root->d_inode->i_sb is a weird way to spell m->mnt_sb...
linux/mount.h: trim includes
uninline may_mount() and don't opencode it in fspick(2)/fsopen(2)
Linus Torvalds [Sun, 5 Jun 2022 01:52:00 +0000 (18:52 -0700)]
Merge tag 'pull-18-rc1-work.fd' of git://git./linux/kernel/git/viro/vfs
Pull file descriptor updates from Al Viro.
- Descriptor handling cleanups
* tag 'pull-18-rc1-work.fd' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Unify the primitives for file descriptor closing
fs: remove fget_many and fput_many interface
io_uring_enter(): don't leave f.flags uninitialized
Linus Torvalds [Sun, 5 Jun 2022 00:42:33 +0000 (17:42 -0700)]
Merge tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs client fixes from Steve French:
"Nine cifs/smb3 client fixes.
Includes DFS fixes, some cleanup of leagcy SMB1 code, duplicated
message cleanup and a double free and deadlock fix"
* tag '5.19-rc-smb3-client-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix uninitialized pointer in error case in dfs_cache_get_tgt_share
cifs: skip trailing separators of prefix paths
cifs: update internal module number
cifs: version operations for smb20 unneeded when legacy support disabled
cifs: do not build smb1ops if legacy support is disabled
cifs: fix potential deadlock in direct reclaim
cifs: when extending a file with falloc we should make files not-sparse
cifs: remove repeated debug message on cifs_put_smb_ses()
cifs: fix potential double free during failed mount
Schspa Shi [Fri, 3 Jun 2022 09:38:52 +0000 (17:38 +0800)]
kbuild: Allow to select bash in a modified environment
This fixes the build error when the system has a default bash version
which is too old to support associative array variables.
The build error log as fellowing:
linux/scripts/check-local-export: line 11: declare: -A: invalid option
declare: usage: declare [-afFirtx] [-p] [name[=value] ...]
Signed-off-by: Schspa Shi <schspa@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Isak Ellmer [Wed, 1 Jun 2022 13:08:19 +0000 (15:08 +0200)]
scripts: kconfig: nconf: make nconfig accept jk keybindings
Make nconfig accept jk keybindings for movement in addition to arrow
keys.
Signed-off-by: Isak Ellmer <isak01@gmail.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Mon, 30 May 2022 09:01:39 +0000 (18:01 +0900)]
modpost: use fnmatch() to simplify match()
Replace the own implementation for wildcard (glob) matching with
a function call to fnmatch().
Also, change the return type to 'bool'.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Masahiro Yamada [Mon, 30 May 2022 09:01:38 +0000 (18:01 +0900)]
modpost: simplify mod->name allocation
mod->name is set to the ELF filename with the suffix ".o" stripped.
The current code calls strdup() and free() to manipulate the string,
but a simpler approach is to pass new_module() with the name length
subtracted by 2.
Also, check if the passed filename ends with ".o" before stripping it.
The current code blindly chops the suffix:
tmp[strlen(tmp) - 2] = '\0'
It will cause buffer under-run if strlen(tmp) < 2;
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Masahiro Yamada [Sat, 28 May 2022 15:47:04 +0000 (00:47 +0900)]
kbuild: factor out the common objtool arguments
scripts/Makefile.build and scripts/link-vmlinux.sh have similar setups
for the objtool arguments.
It was difficult to factor out them because all the vmlinux build rules
were written in a shell script. It is somewhat tedious to touch the two
files every time a new objtool option is supported.
To reduce the code duplication, move the objtool for vmlinux.o into
scripts/Makefile.vmlinux_o. Then, move the common macros to Makefile.lib
so they are shared between Makefile.build and Makefile.vmlinux_o.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM-14 (x86-64)
Masahiro Yamada [Sat, 28 May 2022 15:47:03 +0000 (00:47 +0900)]
kbuild: move vmlinux.o link to scripts/Makefile.vmlinux_o
This is a preparation for moving the objtool rule in the next commit.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM-14 (x86-64)
Masahiro Yamada [Sat, 28 May 2022 15:47:02 +0000 (00:47 +0900)]
kbuild: clean .tmp_* pattern by make clean
Change the "make clean" rule to remove all the .tmp_* files.
.tmp_objdiff is the only exception, which should be removed by
"make mrproper".
Rename the record directory of objdiff, .tmp_objdiff to .objdiff to
avoid the removal by "make clean".
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com> # LLVM-14 (x86-64)
Linus Torvalds [Sat, 4 Jun 2022 21:04:27 +0000 (14:04 -0700)]
Merge tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- bitmap: optimize bitmap_weight() usage, from me
- lib/bitmap.c make bitmap_print_bitmask_to_buf parseable, from Mauro
Carvalho Chehab
- include/linux/find: Fix documentation, from Anna-Maria Behnsen
- bitmap: fix conversion from/to fix-sized arrays, from me
- bitmap: Fix return values to be unsigned, from Kees Cook
It has been in linux-next for at least a week with no problems.
* tag 'bitmap-for-5.19-rc1' of https://github.com/norov/linux: (31 commits)
nodemask: Fix return values to be unsigned
bitmap: Fix return values to be unsigned
KVM: x86: hyper-v: replace bitmap_weight() with hweight64()
KVM: x86: hyper-v: fix type of valid_bank_mask
ia64: cleanup remove_siblinginfo()
drm/amd/pm: use bitmap_{from,to}_arr32 where appropriate
KVM: s390: replace bitmap_copy with bitmap_{from,to}_arr64 where appropriate
lib/bitmap: add test for bitmap_{from,to}_arr64
lib: add bitmap_{from,to}_arr64
lib/bitmap: extend comment for bitmap_(from,to)_arr32()
include/linux/find: Fix documentation
lib/bitmap.c make bitmap_print_bitmask_to_buf parseable
MAINTAINERS: add cpumask and nodemask files to BITMAP_API
arch/x86: replace nodes_weight with nodes_empty where appropriate
mm/vmstat: replace cpumask_weight with cpumask_empty where appropriate
clocksource: replace cpumask_weight with cpumask_empty in clocksource.c
genirq/affinity: replace cpumask_weight with cpumask_empty where appropriate
irq: mips: replace cpumask_weight with cpumask_empty where appropriate
drm/i915/pmu: replace cpumask_weight with cpumask_empty where appropriate
arch/x86: replace cpumask_weight with cpumask_empty where appropriate
...
Linus Torvalds [Sat, 4 Jun 2022 20:50:23 +0000 (13:50 -0700)]
Merge tag 'for-5.19/parisc-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull more parisc architecture updates from Helge Deller:
"A fix to prevent crash at bootup if CONFIG_SCHED_MC is enabled, and
add auto-detection of primary graphics card for framebuffer driver"
* tag 'for-5.19/parisc-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/stifb: Keep track of hardware path of graphics card
parisc/stifb: Implement fb_is_primary_device()
parisc: fix a crash with multicore scheduler
Linus Torvalds [Sat, 4 Jun 2022 20:42:53 +0000 (13:42 -0700)]
Merge tag 'for-linus-5.19-rc1b-tag' of git://git./linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
"Two cleanup patches for Xen related code and (more important) an
update of MAINTAINERS for Xen, as Boris Ostrovsky decided to step
down"
* tag 'for-linus-5.19-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: replace xen_remap() with memremap()
MAINTAINERS: Update Xen maintainership
xen: switch gnttab_end_foreign_access() to take a struct page pointer
Linus Torvalds [Sat, 4 Jun 2022 20:33:12 +0000 (13:33 -0700)]
Merge tag 'perf-tools-for-v5.19-2022-06-04' of git://git./linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Synthesize task events for pre-existing threads when using 'perf lock
--threads', as we need to show task names.
- Fix unwinding with ld.lld (>= version 10.0) linked objects, where
.eh_frame_hdr and .text are in different PT_LOAD program headers,
which makes perf record --call-graph dwarf fail with such obkects.
- Check if 'perf record' hangs in the ARM SPE (Statistical Profiling
Extensions) 'perf test' entry when recording a workload with forks.
- Trace physical address for Arm SPE events, needed for 'perf c2c' to
locate the memory node for samples.
- Fix sorting in percent_rmt_hitm_cmp() in 'perf c2c'.
- Further support for Intel hybrid systems in the evlist and 'perf
record' code.
- Update IBM s/390 vendor event JSON tables.
- Add metrics (JSON) for Intel Sapphirerapids.
- Update metrics for Intel Alderlake.
- Correct typo of sysf 'event_source' directory in the documentation.
* tag 'perf-tools-for-v5.19-2022-06-04' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf vendor events intel: Update metrics for Alderlake
perf vendor events intel: Add metrics for Sapphirerapids
perf c2c: Fix sorting in percent_rmt_hitm_cmp()
perf mem: Trace physical address for Arm SPE events
perf list: Update event description for IBM zEC12/zBC12 to latest level
perf list: Update event description for IBM z196/z114 to latest level
perf list: Update event description for IBM z15 to latest level
perf list: Update event description for IBM z14 to latest level
perf list: Update event description for IBM z13 to latest level
perf list: Update event description for IBM z10 to latest level
perf list: Add IBM z16 event description for s390
perf record: Support sample-read topdown metric group for hybrid platforms
perf lock: Change to synthesize task events
perf unwind: Fix segbase for ld.lld linked objects
perf test arm-spe: Check if perf-record hangs when recording workload with forks
perf docs: Correct typo of event_sources
perf evlist: Extend arch_evsel__must_be_in_group to support hybrid systems
Steve French [Sat, 4 Jun 2022 06:18:37 +0000 (01:18 -0500)]
cifs: fix uninitialized pointer in error case in dfs_cache_get_tgt_share
Set default value of ppath to null.
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Steve French <stfrench@microsoft.com>
Helge Deller [Thu, 2 Jun 2022 11:55:26 +0000 (13:55 +0200)]
parisc/stifb: Keep track of hardware path of graphics card
Keep the pa_path (hardware path) of the graphics card in sti_struct and use
this info to give more useful info which card is currently being used.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Helge Deller [Thu, 2 Jun 2022 11:50:44 +0000 (13:50 +0200)]
parisc/stifb: Implement fb_is_primary_device()
Implement fb_is_primary_device() function, so that fbcon detects if this
framebuffer belongs to the default graphics card which was used to start
the system.
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # v5.10+
Linus Torvalds [Sat, 4 Jun 2022 03:01:25 +0000 (20:01 -0700)]
Merge tag 'gpio-fixes-for-v5.19-rc1' of git://git./linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
- use the correct register for regcache sync in gpio-pca953x
- remove unused and potentially harmful code from gpio-adp5588
- MAINTAINERS update
* tag 'gpio-fixes-for-v5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: adp5588: Remove support for platform setup and teardown callbacks
gpio: pca953x: use the correct register address to do regcache sync
MAINTAINERS: Update Intel GPIO (PMIC and PCH) to Supported
MAINTAINERS: Update GPIO ACPI library to Supported
Linus Torvalds [Sat, 4 Jun 2022 02:57:25 +0000 (19:57 -0700)]
Merge tag 'regulator-fix-v5.19-rc0' of git://git./linux/kernel/git/broonie/regulator
Pull regulator fix from Mark Brown:
"One fix that came in during the merge window, fixing an error in the
examples in the DT binding documentation for mt6315"
* tag 'regulator-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: mt6315-regulator: fix invalid allowed mode
Linus Torvalds [Fri, 3 Jun 2022 23:57:16 +0000 (16:57 -0700)]
Merge tag 'ntfs3_for_5.19' of https://github.com/Paragon-Software-Group/linux-ntfs3
Pull ntfs3 updates from Konstantin Komarov:
- fix some memory leaks and panic
- fixed xfstests (tested on x86_64): generic/092 generic/099
generic/228 generic/240 generic/307 generic/444
- fix some typos, dead code, etc
* tag 'ntfs3_for_5.19' of https://github.com/Paragon-Software-Group/linux-ntfs3:
fs/ntfs3: provide block_invalidate_folio to fix memory leak
fs/ntfs3: Fix invalid free in log_replay
fs/ntfs3: Update valid size if -EIOCBQUEUED
fs/ntfs3: Check new size for limits
fs/ntfs3: Fix fiemap + fix shrink file size (to remove preallocated space)
fs/ntfs3: In function ntfs_set_acl_ex do not change inode->i_mode if called from function ntfs_init_acl
fs/ntfs3: Optimize locking in ntfs_save_wsl_perm
fs/ntfs3: Update i_ctime when xattr is added
fs/ntfs3: Restore ntfs_xattr_get_acl and ntfs_xattr_set_acl functions
fs/ntfs3: Keep preallocated only if option prealloc enabled
fs/ntfs3: Fix some memory leaks in an error handling path of 'log_replay()'
Linus Torvalds [Fri, 3 Jun 2022 23:13:25 +0000 (16:13 -0700)]
Merge tag 'ptrace_stop-cleanup-for-v5.19' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull ptrace_stop cleanups from Eric Biederman:
"While looking at the ptrace problems with PREEMPT_RT and the problems
Peter Zijlstra was encountering with ptrace in his freezer rewrite I
identified some cleanups to ptrace_stop that make sense on their own
and move make resolving the other problems much simpler.
The biggest issue is the habit of the ptrace code to change
task->__state from the tracer to suppress TASK_WAKEKILL from waking up
the tracee. No other code in the kernel does that and it is straight
forward to update signal_wake_up and friends to make that unnecessary.
Peter's task freezer sets frozen tasks to a new state TASK_FROZEN and
then it stores them by calling "wake_up_state(t, TASK_FROZEN)" relying
on the fact that all stopped states except the special stop states can
tolerate spurious wake up and recover their state.
The state of stopped and traced tasked is changed to be stored in
task->jobctl as well as in task->__state. This makes it possible for
the freezer to recover tasks in these special states, as well as
serving as a general cleanup. With a little more work in that
direction I believe TASK_STOPPED can learn to tolerate spurious wake
ups and become an ordinary stop state.
The TASK_TRACED state has to remain a special state as the registers
for a process are only reliably available when the process is stopped
in the scheduler. Fundamentally ptrace needs acess to the saved
register values of a task.
There are bunch of semi-random ptrace related cleanups that were found
while looking at these issues.
One cleanup that deserves to be called out is from commit
57b6de08b5f6
("ptrace: Admit ptrace_stop can generate spuriuos SIGTRAPs"). This
makes a change that is technically user space visible, in the handling
of what happens to a tracee when a tracer dies unexpectedly. According
to our testing and our understanding of userspace nothing cares that
spurious SIGTRAPs can be generated in that case"
* tag 'ptrace_stop-cleanup-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sched,signal,ptrace: Rework TASK_TRACED, TASK_STOPPED state
ptrace: Always take siglock in ptrace_resume
ptrace: Don't change __state
ptrace: Admit ptrace_stop can generate spuriuos SIGTRAPs
ptrace: Document that wait_task_inactive can't fail
ptrace: Reimplement PTRACE_KILL by always sending SIGKILL
signal: Use lockdep_assert_held instead of assert_spin_locked
ptrace: Remove arch_ptrace_attach
ptrace/xtensa: Replace PT_SINGLESTEP with TIF_SINGLESTEP
ptrace/um: Replace PT_DTRACE with TIF_SINGLESTEP
signal: Replace __group_send_sig_info with send_signal_locked
signal: Rename send_signal send_signal_locked
Linus Torvalds [Fri, 3 Jun 2022 23:03:05 +0000 (16:03 -0700)]
Merge tag 'kthread-cleanups-for-v5.19' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull kthread updates from Eric Biederman:
"This updates init and user mode helper tasks to be ordinary user mode
tasks.
Commit
40966e316f86 ("kthread: Ensure struct kthread is present for
all kthreads") caused init and the user mode helper threads that call
kernel_execve to have struct kthread allocated for them. This struct
kthread going away during execve in turned made a use after free of
struct kthread possible.
Here, commit
343f4c49f243 ("kthread: Don't allocate kthread_struct for
init and umh") is enough to fix the use after free and is simple
enough to be backportable.
The rest of the changes pass struct kernel_clone_args to clean things
up and cause the code to make sense.
In making init and the user mode helpers tasks purely user mode tasks
I ran into two complications. The function task_tick_numa was
detecting tasks without an mm by testing for the presence of
PF_KTHREAD. The initramfs code in populate_initrd_image was using
flush_delayed_fput to ensuere the closing of all it's file descriptors
was complete, and flush_delayed_fput does not work in a userspace
thread.
I have looked and looked and more complications and in my code review
I have not found any, and neither has anyone else with the code
sitting in linux-next"
* tag 'kthread-cleanups-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
sched: Update task_tick_numa to ignore tasks without an mm
fork: Stop allowing kthreads to call execve
fork: Explicitly set PF_KTHREAD
init: Deal with the init process being a user mode process
fork: Generalize PF_IO_WORKER handling
fork: Explicity test for idle tasks in copy_thread
fork: Pass struct kernel_clone_args into copy_thread
kthread: Don't allocate kthread_struct for init and umh
Linus Torvalds [Fri, 3 Jun 2022 22:54:57 +0000 (15:54 -0700)]
Merge tag 'per-namespace-ipc-sysctls-for-v5.19' of git://git./linux/kernel/git/ebiederm/user-namespace
Pull ipc sysctl namespace updates from Eric Biederman:
"This updates the ipc sysctls so that they are fundamentally per ipc
namespace. Previously these sysctls depended upon a hack to simulate
being per ipc namespace by looking up the ipc namespace in read or
write. With this set of changes the ipc sysctls are registered per ipc
namespace and open looks up the ipc namespace.
Not only does this series of changes ensure the traditional binding at
open time happens, but it sets a foundation for being able to relax
the permission checks to allow a user namspace root to change the ipc
sysctls for an ipc namespace that the user namespace root requires. To
do this requires the ipc namespace to be known at open time"
* tag 'per-namespace-ipc-sysctls-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
ipc: Remove extra braces
ipc: Check permissions for checkpoint_restart sysctls at open time
ipc: Remove extra1 field abuse to pass ipc namespace
ipc: Use the same namespace to modify and validate
ipc: Store ipc sysctls in the ipc namespace
ipc: Store mqueue sysctls in the ipc namespace
Linus Torvalds [Fri, 3 Jun 2022 22:46:03 +0000 (15:46 -0700)]
firmware_loader: enable XZ by default if compressed support is enabled
Commit
23cfbc6ec44e ("firmware: Add the support for ZSTD-compressed
firmware files") added support for ZSTD compression, but in the process
also made the previously default XZ compression a config option.
That means that anybody who upgrades their kernel and does a
make oldconfig
to update their configuration, will end up without the XZ compression
that the configuration used to have.
Add the 'default y' to make sure this doesn't happen.
The whole compression question should probably be improved upon, since
it is now possible to "enable" compression in the kernel config but not
enable any actual compression algorithm, which makes it all very
useless. It makes no sense to ask Kconfig questions that enable
situations that are nonsensical like that.
This at least fixes the immediate problem of a kernel update resulting
in a nonbootable machine because of a missed option.
Fixes:
23cfbc6ec44e ("firmware: Add the support for ZSTD-compressed firmware files")
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Fri, 3 Jun 2022 21:42:24 +0000 (14:42 -0700)]
Merge tag 'for-linus-5.19-rc1' of git://git./linux/kernel/git/rw/ubifs
Pull JFFS2, UBI and UBIFS updates from Richard Weinberger:
"JFFS2:
- Fixes for a memory leak
UBI:
- Fixes for fastmap (UAF, high CPU usage)
UBIFS:
- Minor cleanups"
* tag 'for-linus-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: ubi_create_volume: Fix use-after-free when volume creation failed
ubi: fastmap: Check wl_pool for free peb before wear leveling
ubi: fastmap: Fix high cpu usage of ubi_bgt by making sure wl_pool not empty
ubifs: Use NULL instead of using plain integer as pointer
ubifs: Simplify the return expression of run_gc()
jffs2: fix memory leak in jffs2_do_fill_super
jffs2: Use kzalloc instead of kmalloc/memset