media: smiapp: fix timeout checking in smiapp_read_nvm

The current code decrements the timeout counter i and the end of
each loop i is incremented, so the check for timeout will always
be false and hence the timeout mechanism is just a dead code path.
Potentially, if the RD_READY bit is not set, we could end up in
an infinite loop.

Fix this so the timeout starts from 1000 and decrements to zero,
if at the end of the loop i is zero we have a timeout condition.

Detected by CoverityScan, CID#1324008 ("Logically dead code")

Fixes: ccfc97bdb5ae ("[media] smiapp: Add driver")

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Add a driver for the ov7251 camera sensor

The ov7251 sensor is a 1/7.5-Inch B&W VGA (640x480) CMOS Digital Image
Sensor from Omnivision.

The driver supports the following modes:
- 640x480 30fps
- 640x480 60fps
- 640x480 90fps

Output format is 10bit B&W RAW - MEDIA_BUS_FMT_Y10_1X10.

The driver supports configuration via user controls for:
- exposure and gain;
- horizontal and vertical flip;
- test pattern.

[Sakari Ailus: Wrap a line over 80 characters, fix trivial sparse warning]

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Binding document for OV7251 camera sensor

Add the document for ov7251 device tree binding.

CC: Rob Herring <robh@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
CC: devicetree@vger.kernel.org
Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Program the visible resolution

The active frame size is set in the initialization arrays, but the value
itself is also available in the struct ov5640_mode_info.

Let's move these values out of the big bytes arrays, and program it with
the value of the mode that we are given.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Add horizontal and vertical totals

All the initialization arrays are changing the horizontal and vertical
totals for some value.

In order to clean up the driver, and since we're going to need that value
later on, let's introduce in the ov5640_mode_info structure the horizontal
and vertical total sizes, and move these out of the bytes array.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Change horizontal and vertical resolutions name

The current width and height parameters in the struct ov5640_mode_info are
actually the active horizontal and vertical resolutions.

Since we're going to add a few other parameters, let's pick a better, more
precise name for these values.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Init properly the SCLK dividers

The SCLK and SCLK2X dividers are fixed in stone in the initialization
array. Let's make explicit what we're doing and move that away from the
huge array to the initialization code.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Don't force the auto exposure state at start time

The sensor needs to have the auto exposure stopped while changing mode.
However, when the new mode is set, the driver will force the auto exposure
on, disregarding whether the control has been changed or not.

Bypass the controls code entirely to do that, and only use the control
value cached when restoring the auto exposure mode.

Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Add light frequency control

Add the light frequency control to be able to set the frequency
to manual (50Hz or 60Hz) or auto.

[Sakari Ailus: Rename "ctl" as "ctrl" as agreed.]
[mchehab+samsung@kernel.org: fixed two coding style warnings]

Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov2640: make s_ctrl() work in power-down mode

The s_ctrl() operation can be called when the device is placed into
power down mode.  Then, applying controls to H/W should be postponed at
this time.  Instead the controls will be restored when the streaming is
started.

Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov2640: make set_fmt() work in power-down mode

The set_fmt() subdev pad operation for this driver currently does not
only do the driver internal format selection but also do the actual
register setup.

This doesn't work if the device power control via GPIO lines is enabled.
Because the set_fmt() can be called when the device is placed into power
down mode.

First of all, this fix adds flag to keep track of whether the device starts
streaming or not.  Then, the set_fmt() postpones applying the actual
register setup at this time.  Instead the setup will be applied when the
streaming is started.

Cc: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5645: Fix write_reg return code

I2C transfer functions return number of successful operations (on success).

Do not return the received positive return code but instead return 0 on
success. The users of write_reg function already use this logic.

Signed-off-by: Todor Tomov <todor.tomov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: ov5640: Use dev_fwnode() to obtain device's fwnode

Use dev_fwnode() on the device instead of getting an fwnode handle of the
device's OF node. The result is the same on OF-based systems and looks
better, too.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: drm: rcar-du: Add support for CRC computation

Implement CRC computation configuration and reporting through the DRM
debugfs-based CRC API. The CRC source can be configured to any input
plane or the pipeline output.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Integrate DISCOM in display pipeline

The DISCOM is used to compute CRCs on display frames. Integrate it in
the display pipeline at the output of the blending unit to process
output frames.

Computing CRCs on input frames is possible by positioning the DISCOM at
a different point in the pipeline. This use case isn't supported at the
moment and could be implemented by extending the API between the VSP1
and DU drivers if needed.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Add support for the DISCOM entity

The DISCOM calculates a CRC on a configurable window of the frame. It
interfaces to the VSP through the UIF glue, hence the name used in the
code.

The module supports configuration of the CRC window through the crop
rectangle on the sink pad of the corresponding entity. However, unlike
the traditional V4L2 subdevice model, the crop rectangle does not
influence the format on the source pad.

Modeling the DISCOM as a sink-only entity would allow adhering to the
V4L2 subdevice model at the expense of more complex code in the driver,
as at the hardware level the UIF is handled as a sink+source entity. As
the DISCOM is only present in R-Car Gen3 VSP-D and VSP-DL instances it
is not exposed to userspace through V4L2 but controlled through the DU
driver. We can thus change this model later if needed without fear of
affecting userspace.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Extend the DU API to support CRC computation

Add a parameter (in the form of a structure to ease future API
extensions) to the VSP atomic flush handler to pass CRC source
configuration, and pass the CRC value to the completion callback.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Document the vsp1_du_atomic_config structure

The structure is used in the API that the VSP1 driver exposes to the DU
driver. Documenting it is thus important.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Reset the crop and compose rectangles in the set_fmt helper

To make vsp1_subdev_set_pad_format() usable by entities that support
selection rectangles, we need to reset the crop and compose rectangles
when setting the format on the sink pad. Do so and replace the custom
set_fmt implementation of the histogram code by a call to
vsp1_subdev_set_pad_format().

Resetting the crop and compose rectangles for entities that don't
support crop and compose has no adverse effect as the rectangles are
ignored anyway.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Share the CLU, LIF and LUT set_fmt pad operation code

The implementation of the set_fmt pad operation is identical in the
three modules. Move it to a generic helper function.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: vsp1: Use SPDX license headers

Adopt the SPDX license identifier headers to ease license compliance
management. All files in the driver are licensed under the GPLv2+ except
for the vsp1_regs.h file which is licensed under the GPLv2. This is
likely an oversight, but fixing this requires contacting the copyright
owners and is out of scope for this patch.

While at it fix the file descriptions to match file names where copy and
paste error occurred.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: cadence: Add Cadence MIPI-CSI2 TX driver

The Cadence MIPI-CSI2 TX controller is an hardware block meant to be used
as a bridge between pixel interfaces and a CSI-2 bus.

It supports operating with an internal or external D-PHY, with up to 4
lanes, or without any D-PHY. The current code only supports the latter
case.

While the virtual channel input on the pixel interface can be directly
mapped to CSI2, the datatype input is actually a selection signal (3-bits)
mapping to a table of up to 8 preconfigured datatypes/formats (programmed
at start-up)

The block supports up to 8 input datatypes.

Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cadence: csi2rx: Fix csi2rx_start error handling

The clocks enabled by csi2rx_start function are intended to be disabled in
an error path but there are two issues:

1) the loop condition is always true and

2) the first clock disabled is the the one enabling of which failed.

Fix these two bugs by changing the loop condition as well as only disabling
the clocks that were actually enabled.

Reported-by: Mauro Chehab <mchehab@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Add Cadence MIPI-CSI2 TX Device Tree bindings

The Cadence MIPI-CSI2 TX controller is a CSI2 bridge that supports up to 4
video streams and can output on up to 4 CSI-2 lanes, depending on the
hardware implementation.

It can operate with an external D-PHY, an internal one or no D-PHY at all
in some configurations.

Acked-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l: cadence: Add Cadence MIPI-CSI2 RX driver

The Cadence CSI-2 RX Controller is an hardware block meant to be used as a
bridge between a CSI-2 bus and pixel grabbers.

It supports operating with internal or external D-PHY, with up to 4 lanes,
or without any D-PHY. The current code only supports the latter case.

It also support dynamic mapping of the CSI-2 virtual channels to the
associated pixel grabbers, but that isn't allowed at the moment either.

Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: Add Cadence MIPI-CSI2 RX Device Tree bindings

The Cadence MIPI-CSI2 RX controller is a CSI2RX bridge that supports up to
4 CSI-2 lanes, and can route the frames to up to 4 streams, depending on
the hardware implementation.

It can operate with an external D-PHY, an internal one or no D-PHY at all
in some configurations.

Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: atomisp: Remove driver

The atomisp driver has a long list of todo items and little has been done
to address these lately while more has been added. The driver is also not
functional. In other words, the driver would not be getting out of staging
in the foreseeable future. At the same time it consumes developer
resources in order to maintain the flaky code base. Remove it.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp-mt9m114: comment out unused stuff

There are lots of data structs defined there but aren't used
anywhere.

Comment them out. Gets rid of those warnings:

drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:1808:45: warning: 'mt9m114_entity_ops' defined but not used [-Wunused-const-variable=]
 static const struct media_entity_operations mt9m114_entity_ops = {
                                             ^~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:35:0:
drivers/staging/media/atomisp/i2c/mt9m114.h:805:34: warning: 'mt9m114_iq' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_iq[] = {
                                  ^~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:797:34: warning: 'mt9m114_antiflicker_60hz' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_antiflicker_60hz[] = {
                                  ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:789:34: warning: 'mt9m114_antiflicker_50hz' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_antiflicker_50hz[] = {
                                  ^~~~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:682:34: warning: 'mt9m114_720_480P_init' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_720_480P_init[] = {
                                  ^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:533:34: warning: 'mt9m114_960P_init' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_960P_init[] = {
                                  ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:518:34: warning: 'mt9m114_wakeup_reg' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_wakeup_reg[] = {
                                  ^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:504:34: warning: 'mt9m114_streaming' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_streaming[] = {
                                  ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:497:34: warning: 'mt9m114_suspend' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_suspend[] = {
                                  ^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/mt9m114.h:393:34: warning: 'mt9m114_exitstandby' defined but not used [-Wunused-const-variable=]
 static struct misensor_reg const mt9m114_exitstandby[] = {
                                  ^~~~~~~~~~~~~~~~~~~

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp-mt9m114: remove dead data

It seems that, originally, the logic would allow selecting between
fine and coarse integration. However, only coarse seems to be
implemented.

Get rid of this warning:

  drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c: In function 'mt9m114_s_exposure':
  drivers/staging/media/atomisp/i2c/atomisp-mt9m114.c:1003:6: warning: variable 'exposure_local' set but not used [-Wunused-but-set-variable]
    u16 exposure_local[3];
        ^~~~~~~~~~~~~~

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp-gc0310: return errors at gc0310_init()

If something wrong gets there, return the error.

Get rid of this warning:

  drivers/staging/media/atomisp/i2c/atomisp-gc0310.c: In function 'gc0310_init':
  drivers/staging/media/atomisp/i2c/atomisp-gc0310.c:713:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
    int ret;
        ^~~

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp: ov2680: don't declare unused vars

drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘__ov2680_set_exposure’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:400:10: warning: variable ‘hts’ set but not used [-Wunused-but-set-variable]
  u16 vts,hts;
          ^~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function ‘ov2680_detect’:
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:1164:5: warning: variable ‘revision’ set but not used [-Wunused-but-set-variable]
  u8 revision;
     ^~~~~~~~

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: atomisp: Comment out several unused sensor resolutions

The register settings for several resolutions aren't used
currently. So, comment them out.

Fix those warnings:

In file included from drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:35:0:
drivers/staging/media/atomisp/i2c/gc2235.h:340:32: warning: 'gc2235_960_640_30fps' defined but not used [-Wunused-const-variable=]
 static struct gc2235_reg const gc2235_960_640_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/gc2235.h:287:32: warning: 'gc2235_1296_736_30fps' defined but not used [-Wunused-const-variable=]
 static struct gc2235_reg const gc2235_1296_736_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2722.c:35:0:
drivers/staging/media/atomisp/i2c/ov2722.h:999:32: warning: 'ov2722_720p_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_720p_30fps[] = {
                                ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:787:32: warning: 'ov2722_1M3_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_1M3_30fps[] = {
                                ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:476:32: warning: 'ov2722_VGA_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_VGA_30fps[] = {
                                ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:367:32: warning: 'ov2722_480P_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_480P_30fps[] = {
                                ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2722.h:257:32: warning: 'ov2722_QVGA_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov2722_reg const ov2722_QVGA_30fps[] = {
                                ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/atomisp-ov2680.c: In function '__ov2680_set_exposure':
In file included from drivers/staging/media/atomisp/i2c/atomisp-ov2680.c:35:0:
At top level:
drivers/staging/media/atomisp/i2c/ov2680.h:736:33: warning: 'ov2680_1616x1082_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_1616x1082_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:649:33: warning: 'ov2680_1456x1096_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_1456x1096_30fps[]= {
                                 ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:606:33: warning: 'ov2680_1296x976_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_1296x976_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:563:33: warning: 'ov2680_720p_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_720p_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:520:33: warning: 'ov2680_800x600_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_800x600_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:475:33: warning: 'ov2680_720x592_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_720x592_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:433:33: warning: 'ov2680_656x496_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_656x496_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:389:33: warning: 'ov2680_QVGA_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_QVGA_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:346:33: warning: 'ov2680_CIF_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_CIF_30fps[] = {
                                 ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov2680.h:301:33: warning: 'ov2680_QCIF_30fps' defined but not used [-Wunused-const-variable=]
  static struct ov2680_reg const ov2680_QCIF_30fps[] = {
                                 ^~~~~~~~~~~~~~~~~
In file included from drivers/staging/media/atomisp/i2c/ov5693/atomisp-ov5693.c:36:0:
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:988:32: warning: 'ov5693_1424x1168_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1424x1168_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:954:32: warning: 'ov5693_2592x1944_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_2592x1944_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:889:32: warning: 'ov5693_2592x1456_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_2592x1456_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:862:32: warning: 'ov5693_1940x1096' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1940x1096[] = {
                                ^~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:796:32: warning: 'ov5693_1636p_30fps' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1636p_30fps[] = {
                                ^~~~~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:758:32: warning: 'ov5693_1296x736' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1296x736[] = {
                                ^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:730:32: warning: 'ov5693_976x556' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_976x556[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:672:32: warning: 'ov5693_736x496' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_736x496[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:643:32: warning: 'ov5693_192x160' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_192x160[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:616:32: warning: 'ov5693_368x304' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_368x304[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:587:32: warning: 'ov5693_336x256' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_336x256[] = {
                                ^~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:540:32: warning: 'ov5693_1296x976' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_1296x976[] = {
                                ^~~~~~~~~~~~~~~
drivers/staging/media/atomisp/i2c/ov5693/ov5693.h:509:32: warning: 'ov5693_654x496' defined but not used [-Wunused-const-variable=]
 static struct ov5693_reg const ov5693_654x496[] = {
                                ^~~~~~~~~~~~~~

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: atomisp-gc2235: don't fill an unused var

The code with uses the dummy var is commented out. So,
coment out its definition/initialization.

Fix this warning:

  drivers/staging/media/atomisp/i2c/atomisp-gc2235.c: In function 'gc2235_get_intg_factor':
  drivers/staging/media/atomisp/i2c/atomisp-gc2235.c:249:26: warning: variable 'dummy' set but not used [-Wunused-but-set-variable]
    u16 reg_val, reg_val_h, dummy;
                            ^~~~~

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp: ov2680.h: fix identation

The identation for several tables there are broken.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: atomisp: reenable warnings for I2C

When atomisp got merged, there were so many warnings with W=1
that we simply disabled the ones that were causing troubles.

Since then, several changes got applied to atomisp, and the
number of warnings are a way smaller than it used to be.

So, let's reenable warnings there and fix the issues.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: atomisp: get rid of __KERNEL macros

There's no sense for a Kernel driver to have __KERNEL macros
on it.

Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp: fix misleading addr information

IA_CSS_ERROR shows the ddr_buffer_addr as a decimal value with a '0x'
prefix, which is somewhat misleading.

Let's fix it to print hexadecimal, as was intended.

Fixes: 158aeefc("[media] atomisp: Add __printf validation and fix fallout")

Cc: Alan Cox <alan@linux.intel.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: atomisp: Using module_pci_driver

Remove boilerplate code by using macro module_pci_driver.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: atomisp: fix spelling mistake: "diregard" -> "disregard"

Trivial fix to spelling mistake in ia_css_print message text

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb_ca_en50221: prevent using slot_info for Spectre attacs

slot can be controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability,
as warned by smatch:
drivers/media/dvb-core/dvb_ca_en50221.c:1479 dvb_ca_en50221_io_write() warn: potential spectre issue 'ca->slot_info' (local cap)

Acked-by: "Jasmin J." <jasmin@anw.at>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: siano: use GFP_DMA only for smssdio

Right now, the Siano's core uses GFP_DMA for both USB and
SDIO variants of the driver. There's no reason to use it
for USB. So, pass GFP_DMA as a parameter during sms core
register.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: gp8psk: don't abuse of GFP_DMA

There's s no reason why it should be using GFP_DMA there.
This is an USB driver. Any restriction should be, instead,
at HCI core, if any.

Cc: "Luis R. Rodriguez" <mcgrof@kernel.org>
Cc: linux-mm@kvack.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: ite-cir: lower timeout and extend allowed timeout range

The minimum possible timeout of ite-cir is 8 samples, which is
typically about 70us. The driver however changes the FIFO trigger
level from the hardware's default of 1 byte to 17 bytes, so the minimum
usable timeout value is 17 * 8 samples, which is typically about 1.2ms.

Tests showed that using timeouts down to 1.2ms actually work fine.

The current default timeout of 200ms is much longer than necessary and
the maximum timeout of 1s seems to have been chosen a bit arbitrarily.

So change the minimum timeout to the driver's limit of 17 * 8 samples
and bring timeout and maximum timeout in line with the settings
of many other receivers.

Signed-off-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: winbond: do not send reset and timeout raw events on startup

ir_raw_event_set_idle() sends a timeout event which is not needed, and
on startup no reset event is needed either.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: decoders do not need to check for transitions

Drivers should never produce consecutive pulse or space raw events. Should
that occur, we would have bigger problems than this code is trying to
guard against.

Note that we already log an error should a driver misbehave.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: drivers should produce alternate pulse and space timing events

Report an error if this is not the case or any problem with the generated
raw events.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rc: default to idle on at startup or after reset

Any spaces events received after a reset or startup should be discarded,
so ensure the rc device is in idle mode.

This also makes it much easier to detect incorrect raw events, as we will
do in a following commit.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: lirc-func.rst: new ioctl LIRC_GET_REC_TIMEOUT is not in a separate file

This fixes the warning:

Documentation/media/uapi/rc/lirc-func.rst:9: WARNING: toctree contains reference to nonexisting document 'media/uapi/rc/lirc-get-rec-timeout'

The ioctl is documented in lirc-set-rec-timeout.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mceusb: add missing break

Fallthrough is not intended here.

Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mceusb: filter out bogus timing irdata of duration 0

A mceusb device has been observed producing invalid irdata. Proactively
guard against this.

Suggested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: mceusb: MCE_CMD_SETIRTIMEOUT cause strange behaviour on device

If the IR timeout is set on vid 1784 pid 0011, the device starts
behaving strangely.

Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb_frontend: cleanup some coding style errors

This is a core media file... it shoudn't have so many coding
style issues! The last patch ended by being submitted with
an error like that, very likely due to some cut and paste
issue.

Maybe it is time to clean it up. Do it with the auto
fix logic:

 ./scripts/checkpatch.pl -f drivers/media/dvb-core/dvb_frontend.c --strict --fix-inplace

Then manually fix the errors introduced by it.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvbdev: add a mutex protecting the "mdev" pointer

During destruction, a race condition in
dvb_media_controller_disable_source() can cause a kernel crash,
because the "mdev" pointer has been read successfully while another
task executes dvb_usb_media_device_unregister(), which destroys the
object.  Example for such a crash:

    general protection fault: 0000 [#1] SMP
    CPU: 1 PID: 301 Comm: vdr Not tainted 4.8.1-nuc+ #102
    [142B blob data]
    task: ffff8802301f2040 task.stack: ffff880233728000
    RIP: 0010:[<ffffffff816c296b>]  [<ffffffff816c296b>] dvb_frontend_release+0xcb/0x120
    RSP: 0018:ffff88023372bdd8  EFLAGS: 00010202
    RAX: 001fd55c000000da RBX: ffff880236bad810 RCX: 0000000000000000
    RDX: ffff880235bd81f0 RSI: 0000000000000246 RDI: ffff880235bd81e8
    RBP: ffff88023372be00 R08: 0000000000000000 R09: 0000000000000000
    R10: 0000000000000000 R11: ffff88022f009910 R12: 0000000000000000
    R13: ffff880235a21a80 R14: ffff880235bd8000 R15: ffff880235bb8a78
    FS:  0000000000000000(0000) GS:ffff88023fd00000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 00007f96edd69818 CR3: 0000000002406000 CR4: 00000000001006e0
    Stack:
     ffff88022f009900 0000000000000008 ffff880235bb8a78 ffff8802344fbb20
     ffff880236437b40 ffff88023372be48 ffffffff8117a81e ffff880235bb8a78
     ffff88022f009910 ffff8802335a7400 ffff8802301f2040 ffff88022f009900
    Call Trace:
     [<ffffffff8117a81e>] __fput+0xde/0x1d0
     [<ffffffff8117a949>] ____fput+0x9/0x10
     [<ffffffff810a9fce>] task_work_run+0x7e/0xa0
     [<ffffffff81094bab>] do_exit+0x27b/0xa50
     [<ffffffff810407e3>] ? __do_page_fault+0x1c3/0x430
     [<ffffffff81095402>] do_group_exit+0x42/0xb0
     [<ffffffff8109547f>] SyS_exit_group+0xf/0x10
     [<ffffffff8108bedb>] entry_SYSCALL_64_fastpath+0x13/0x8f
    Code: 31 c9 49 8d be e8 01 00 00 ba 01 00 00 00 be 03 00 00 00 e8 68 2d a0 ff 48 8b 83 10 03 00 00 48 8b 80 88 00 00 00 48 85 c0 74 12 <48> 8b 80 88 02 00 00 48 85 c0 74 06 49 8b 7d
    RIP  [<ffffffff816c296b>] dvb_frontend_release+0xcb/0x120

[mchehab+samsung@kernel.org: fix a Coding Style issue]
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: lgdt330x.h: fix compiler warning

Add missing 'inline' to fix this compiler warning:

In file included from drivers/media/common/b2c2/flexcop-fe-tuner.c:21:0:
drivers/media/dvb-frontends/lgdt330x.h:61:22: warning: 'lgdt330x_attach' defined but not used [-Wunused-function]
 struct dvb_frontend *lgdt330x_attach(const struct lgdt330x_config *config,
                      ^~~~~~~~~~~~~~~

Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Suggested-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rcar-vin: fix crop and compose handling for Gen3

When refactoring the Gen3 enablement series crop and compose handling
where broken. This went unnoticed but can result in writing out side the
capture buffer. Fix this by restoring the crop and compose to reflect
the format dimensions as we have not yet enabled the scaler for Gen3.

Fixes: 5e7c623632fcf8f5 ("media: rcar-vin: use different v4l2 operations in media controller mode")

Reported-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Revert "media: rcar-vin: enable field toggle after a set number of lines for Gen3"

The offending commit was an attempt to fix the issue of writing outside
the capture buffer for VIN Gen3. Unfortunately it only fixed the symptom
of the problem to such a degree I could no longer reproduce it. Revert
the offending commit before a proper fix can be added in a follow-up
patch.

This reverts commit 015060cb7795eac34454696cc9c9f8b76926a401.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dvb_frontends: fix spelling mistake: "unexpcted" -> "unexpected"

Trivial fix to spelling mistake in dprintk message text

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: usb: cx231xx-417: include linux/slab.h header

cx231-417 uses kmalloc/kfree functions, so slab header needs to be
included in order to fix the following build errors:
drivers/media/usb/cx231xx/cx231xx-417.c: In function ‘cx231xx_bulk_copy’:
  CC      drivers/media/platform/qcom/venus/firmware.o
drivers/media/usb/cx231xx/cx231xx-417.c:1389:11: error: implicit declaration of function ‘kmalloc’; did you mean ‘vmalloc’? [-Werror=implicit-function-declaration]
  buffer = kmalloc(buffer_size, GFP_ATOMIC);
           ^~~~~~~
           vmalloc
drivers/media/usb/cx231xx/cx231xx-417.c:1389:9: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
  buffer = kmalloc(buffer_size, GFP_ATOMIC);
         ^
drivers/media/usb/cx231xx/cx231xx-417.c:1400:2: error: implicit declaration of function ‘kfree’; did you mean ‘vfree’? [-Werror=implicit-function-declaration]
  kfree(buffer);
  ^~~~~
  vfree
drivers/media/usb/cx231xx/cx231xx-417.c: In function ‘mpeg_open’:
drivers/media/usb/cx231xx/cx231xx-417.c:1713:7: error: implicit declaration of function ‘kzalloc’; did you mean ‘vzalloc’? [-Werror=implicit-function-declaration]
  fh = kzalloc(sizeof(*fh), GFP_KERNEL);
       ^~~~~~~
       vzalloc
drivers/media/usb/cx231xx/cx231xx-417.c:1713:5: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
  fh = kzalloc(sizeof(*fh), GFP_KERNEL);
     ^

Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: i2c: tda1997: Fix an error handling path 'tda1997x_probe()'

If 'media_entity_pads_init()' fails, we must free the resources allocated
by 'v4l2_ctrl_handler_init()', as already done in the previous error
handling path.

'goto' the right label to fix it.

Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver")

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: saa7146: fix error return from master_xfer

Returning -1 (-EPERM) is not appropriate here, go with -EIO.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: em28xx: Demote several dev_err to dev_info

These two statements are not errors, reduce to appropriate level.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cx231xx: Fix spelling mistake: "senario" -> "scenario"

Trivial fix to spelling mistake in dev_err message.

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cx23885: Add some missing register documentation

Document what these two register calls are doing.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cx23885: Expand registers in dma tsport reg dump

Include some additional useful registers in the output.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cx23885: Ryzen DMA related RiSC engine stall fixes

This bug affects all of Hauppauge QuadHD boards when used on all Ryzen
platforms and some XEON platforms. On these platforms it is possible to
error out the RiSC engine and cause it to stall, whereafter the only
way to reset the board to a working state is to reboot.

This is the fatal condition with current driver:

[  255.663598] cx23885: cx23885[0]: mpeg risc op code error
[  255.663607] cx23885: cx23885[0]: TS1 B - dma channel status dump
[  255.663612] cx23885: cx23885[0]:   cmds: init risc lo   : 0xffe54000
[  255.663615] cx23885: cx23885[0]:   cmds: init risc hi   : 0x00000000
[  255.663619] cx23885: cx23885[0]:   cmds: cdt base       : 0x00010870
[  255.663622] cx23885: cx23885[0]:   cmds: cdt size       : 0x0000000a
[  255.663625] cx23885: cx23885[0]:   cmds: iq base        : 0x00010630
[  255.663629] cx23885: cx23885[0]:   cmds: iq size        : 0x00000010
[  255.663632] cx23885: cx23885[0]:   cmds: risc pc lo     : 0xffe54018
[  255.663636] cx23885: cx23885[0]:   cmds: risc pc hi     : 0x00000000
[  255.663639] cx23885: cx23885[0]:   cmds: iq wr ptr      : 0x00004192
[  255.663642] cx23885: cx23885[0]:   cmds: iq rd ptr      : 0x0000418c
[  255.663645] cx23885: cx23885[0]:   cmds: cdt current    : 0x00010898
[  255.663649] cx23885: cx23885[0]:   cmds: pci target lo  : 0xf85ca340
[  255.663652] cx23885: cx23885[0]:   cmds: pci target hi  : 0x00000000
[  255.663655] cx23885: cx23885[0]:   cmds: line / byte    : 0x000c0000
[  255.663659] cx23885: cx23885[0]:   risc0:
[  255.663661] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663666] cx23885: cx23885[0]:   risc1:
[  255.663667] 0xf85ca050 [ INVALID sol 22 20 19 18 resync 13 count=80 ]
[  255.663674] cx23885: cx23885[0]:   risc2:
[  255.663674] 0x00000000 [ INVALID count=0 ]
[  255.663678] cx23885: cx23885[0]:   risc3:
[  255.663679] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663684] cx23885: cx23885[0]:   (0x00010630) iq 0:
[  255.663685] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663690] cx23885: cx23885[0]:   iq 1: 0xf85ca630 [ arg #1 ]
[  255.663693] cx23885: cx23885[0]:   iq 2: 0x00000000 [ arg #2 ]
[  255.663696] cx23885: cx23885[0]:   (0x0001063c) iq 3:
[  255.663697] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663702] cx23885: cx23885[0]:   iq 4: 0xf85ca920 [ arg #1 ]
[  255.663705] cx23885: cx23885[0]:   iq 5: 0x00000000 [ arg #2 ]
[  255.663709] cx23885: cx23885[0]:   (0x00010648) iq 6:
[  255.663709] 0xf85ca340 [ INVALID sol 22 20 19 18 resync 13 count=832 ]
[  255.663716] cx23885: cx23885[0]:   (0x0001064c) iq 7:
[  255.663717] 0x00000000 [ INVALID count=0 ]
[  255.663721] cx23885: cx23885[0]:   (0x00010650) iq 8:
[  255.663721] 0x00000000 [ INVALID count=0 ]
[  255.663725] cx23885: cx23885[0]:   (0x00010654) iq 9:
[  255.663726] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663731] cx23885: cx23885[0]:   iq a: 0xf85c9780 [ arg #1 ]
[  255.663734] cx23885: cx23885[0]:   iq b: 0x00000000 [ arg #2 ]
[  255.663737] cx23885: cx23885[0]:   (0x00010660) iq c:
[  255.663738] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663743] cx23885: cx23885[0]:   iq d: 0xf85c9a70 [ arg #1 ]
[  255.663746] cx23885: cx23885[0]:   iq e: 0x00000000 [ arg #2 ]
[  255.663749] cx23885: cx23885[0]:   (0x0001066c) iq f:
[  255.663750] 0x1c0002f0 [ write sol eol count=752 ]
[  255.663755] cx23885: cx23885[0]:   iq 10: 0xf4fa2920 [ arg #1 ]
[  255.663758] cx23885: cx23885[0]:   iq 11: 0x00000000 [ arg #2 ]
[  255.663759] cx23885: cx23885[0]: fifo: 0x00005000 -> 0x6000
[  255.663760] cx23885: cx23885[0]: ctrl: 0x00010630 -> 0x10690
[  255.663764] cx23885: cx23885[0]:   ptr1_reg: 0x00005980
[  255.663767] cx23885: cx23885[0]:   ptr2_reg: 0x000108a8
[  255.663770] cx23885: cx23885[0]:   cnt1_reg: 0x0000000b
[  255.663773] cx23885: cx23885[0]:   cnt2_reg: 0x00000003

Included is checks of the TC_REQ and TC_REQ_SET registers during states
of board initialization, reset, DMA start, and DMA stop. If both registers
are set, this indicates a stall in the RiSC engine, at which point the
bridge error is cleared.

A small delay is introduced in stop_dma as well, to allow transfers in
progress to finish.

After application all models work on Ryzen, occasionally yielding:

cx23885_clear_bridge_error: dma in progress detected 0x00000001 0x00000001, clearing

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
[hansverk@cisco.com: fix compiler warning of unused 'reg' variable]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cx23885: Use PCI and TS masks in irq functions

Currently mask is read for pci_status/ts1_status/ts2_status, but
otherwise ignored. The masks are now used to determine whether
action is warranted.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cx23885: Handle additional bufs on interrupt

On Ryzen systems interrupts are occasionally missed:

cx23885: cx23885_wakeup: [ffff99b384b83c00/28] wakeup reg=5406 buf=5405
cx23885: cx23885_wakeup: [ffff99b40bf79400/31] wakeup reg=9537 buf=9536

This patch loops up to five times on wakeup, marking any buffers
found done.

Since the count register is u16, but the vb2 counter is u32, some modulo
arithmetic is used to accommodate wraparound and ensure current active
buffer is the buffer expected.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-device.h: always expose mdev

The mdev field is only present if CONFIG_MEDIA_CONTROLLER is set.
But since we will need to pass the media_device to vb2 and the
control framework it is very convenient to just make this field
available all the time. If CONFIG_MEDIA_CONTROLLER is not set,
then it will just be NULL.

Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-ioctl: replace IOCTL_INFO_STD with stub functions

This change removes IOCTL_INFO_STD and adds stub functions where
needed using the DEFINE_V4L_STUB_FUNC macro. This fixes indirect call
mismatches with Control-Flow Integrity, caused by calling standard
ioctls using a function pointer that doesn't match the function type.

Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: hackrf: group device capabilities

Instead of putting V4L2_CAP_STREAMING and V4L2_CAP_READWRITE
everywhere, set device_caps earlier with these values.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: xilinx: regroup caps on querycap

To better organize the code we concentrate the setting of
V4L2_CAP_STREAMING in one place.

Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: staging: media: use relevant lock

The data protected is video_out2 and the lock that is released is
&video_out2->dma_queue_lock, so it seems that that lock should be
taken as well.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: rcar_jpu: Add missing clk_disable_unprepare() on error in jpu_open()

Add the missing clk_disable_unprepare() before return from
jpu_open() in the software reset error handling case.

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Mikhail Ulyanov <mikhail.ulyanov@cogentembedded.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: dt-bindings: media: renesas-ceu: Add R-Mobile R8A7740

Add R-Mobile A1 R8A7740 SoC to the list of compatible values for the CEU
unit.

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: update/fix my e-mail on some places

There are two places pointing to an unexisting "m.chehab@kernel.org"
email. I never had such email, so, I'm unsure how it ends there.
Anyway, it is plain wrong.

While here, use my canonical e-mail on a bunch of places that
are pointing to another e-mail. The idea is that, from now on,
all places will be pointing to the same SMTP server.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

Merge tag 'v4.17-rc4' into patchwork

Linux 4.17-rc4

* tag 'v4.17-rc4': (920 commits)
  Linux 4.17-rc4
  KVM: x86: remove APIC Timer periodic/oneshot spikes
  genksyms: fix typo in parse.tab.{c,h} generation rules
  kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)
  gcc-plugins: fix build condition of SANCOV plugin
  MAINTAINERS: Update Kbuild entry with a few paths
  Revert "usb: host: ehci: Use dma_pool_zalloc()"
  platform/x86: Kconfig: Fix dell-laptop dependency chain.
  platform/x86: asus-wireless: Fix NULL pointer dereference
  arm64: vgic-v2: Fix proxying of cpuif access
  KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance
  KVM: arm64: Fix order of vcpu_write_sys_reg() arguments
  MAINTAINERS & files: Canonize the e-mails I use at files
  media: imx-media-csi: Fix inconsistent IS_ERR and PTR_ERR
  tools: power/acpi, revert to LD = gcc
  bdi: Fix oops in wb_workfn()
  RDMA/cma: Do not query GID during QP state transition to RTR
  IB/mlx4: Fix integer overflow when calculating optimal MTT size
  IB/hfi1: Fix memory leak in exception path in get_irq_affinity()
  IB/{hfi1, rdmavt}: Fix memory leak in hfi1_alloc_devdata() upon failure
  ...

media: dvbsky: use just one mutex for serializing device R/W ops

Right now, there are two mutexes serializing r/w ops: one "generic"
and another one specifically for stream on/off.

Clean it a little bit, getting rid of one of the mutexes.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

qm1d1b0004: fix a warning about an unused default_cfg var

As warned by gcc:

drivers/media/tuners/qm1d1b0004.c:62:39: warning: 'default_cfg' defined but not used [-Wunused-const-variable=]
 static const struct qm1d1b0004_config default_cfg = {
                                       ^~~~~~~~~~~

This var is currently unused. So, comment it out.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: omap3isp: Don't use GFP_DMA

The isp stat driver allocates memory for DMA and uses GFP_DMA flag for
dev_alloc_coherent. The flag is no longer needed as the DMA mask is used
for the purpose. Remove it.

Reported-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: omap3isp: Remove useless NULL check in omap3isp_stat_config

The omap3isp driver checked whether the second argument (the new
configuration) to the ISP statistics is NULL. This is the pointer to the
user-given argument and is never NULL. Remove the check.

Reported-by: "Gustavo A. R. Silva" <gustavo@embeddedor.com>
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: omap3isp: support 64-bit version of omap3isp_stat_data

C libraries with 64-bit time_t use an incompatible format for
struct omap3isp_stat_data. This changes the kernel code to
support either version, by moving over the normal handling
to the 64-bit variant, and adding compatiblity code to handle
the old binary format with the existing ioctl command code.

Fortunately, the command code includes the size of the structure,
so the difference gets handled automatically. In the process of
eliminating the references to 'struct timeval' from the kernel,
I also change the way the timestamp is generated internally,
basically by open-coding the v4l2_get_timestamp() call.

[Sakari Ailus: Alphabetical order of headers, clean up compat code]

Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: media-device: fix ioctl function types

This change fixes function types for media device ioctls to avoid
indirect call mismatches with Control-Flow Integrity checking.

Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx-csi: fix burst size for 16 bit

A burst_size of 4 does not work for the 16 bit passthrough formats, so
we use 8 instead.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: imx: add 16-bit grayscale support

Since commit 50b0f0aee839 ("gpu: ipu-csi: add 10/12-bit grayscale
support to mbus_code_to_bus_cfg") the IPU CSI can be configured to
capture 10-bit and 12-bit grayscale formats, expanded to 16-bit
grayscale, in bayer/generic data mode.
This patch adds support for V4L2_PIX_FMT_Y16 captured from sensors
that provide MEDIA_BUS_FMT_Y10_1X10 or MEDIA_BUS_FMT_Y12_1X12 data.

Cc: Jan Luebbe <jlu@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Revert cleanup ktime_set() usage

This reverts 8b0e195314fa, because media-tree drivers should use the
API functions to initialize variables of type ktime_t.

Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: Use ktime_set() in pt1.c

In commit 20a63349b142 a new variable ktime_t delay has been added.
We decided to use the API functions to initialize ktime_t variables
within media-tree. Thus variable delay needs to be initialized with
ktime_set() instead of setting it directly.

Signed-off-by: Jasmin Jessich <jasmin@anw.at>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: pvrusb2: delete unneeded include

pvrusb2-video-v4l.h only declares pvr2_saa7115_subdev_update and
includes pvrusb2-hdw-internal.h.  pvrusb2-cx2584x-v4l.c does not
use pvr2_saa7115_subdev_update and it explicitly includes
pvrusb2-hdw-internal.h.

Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: saa7164: Fix driver name in debug output

This issue was reported by a user who downloaded a corrupt saa7164
firmware, then went looking for a valid xc5000 firmware to fix the
error displayed...but the device in question has no xc5000, thus after
much effort, the wild goose chase eventually led to a support call.

The xc5000 has nothing to do with saa7164 (as far as I can tell),
so replace the string with saa7164 as well as give a meaningful
hint on the firmware mismatch.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: renesas-ceu: Set mbus_fmt on subdev operations

The renesas-ceu driver intializes the desired mbus_format at 'complete'
time, inspecting the supported subdevice ones, and tuning some
parameters to produce the requested memory format from what the sensor
can produce. Although, the initially selected mbus_format was not
provided to the subdevice during set_fmt and try_fmt operations,
providing instead a '0' mbus format code.

As long as the sensor defaults to a compatible mbus_format when an
invalid code as '0' is provided, capture operations work correctly. If
the subdevice defaults to an unsupported format (eg. some RGB
permutations) capture does not work properly due to a mismatch on the
expected and received image format on the wire.

Fix that by re-using the initially selected mbus_format code during
set_fmt and try_fmt subdevice operation calls.

Tested by printing out the format selection procedure with ov7670
sensor.

Before this patch:
[    0.866001] ov7670_try_fmt_internal -- Looking for mbus_code 0x0000
[    0.870882] ov7670_try_fmt_internal -- Try mbus_code 0x2008
[    0.876336] ov7670_try_fmt_internal -- Try mbus_code 0x1002
[    0.881387] ov7670_try_fmt_internal -- Try mbus_code 0x1008
[    0.886537] ov7670_try_fmt_internal -- Try mbus_code 0x3001
[    0.891584] ov7670_try_fmt_internal -- mbus_code defaulted to 0x2008

With this patch applied:
[    0.867015] ov7670_try_fmt_internal -- Looking for mbus_code 0x2008
[    0.873205] ov7670_try_fmt_internal -- Try mbus_code 0x2008: match

Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: cec: Kconfig coding style issue

Use tabs instead of spaces and help is two-spaced after single tab.

The incorrect spacing breaks menuconfig on older kernels.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: intel-ipu3: Kconfig coding style issue

Kconfig Help statements are two-spaced after a single tab.

The incorrect spacing breaks menuconfig on older kernels.

Signed-off-by: Brad Love <brad@nextdimension.cc>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: em28xx: Fix DualHD broken second tuner

The use of a hard coded i2c address breaks the creation of the
second tuner in DualHD 01595 models. The issue is compounded
by lack of any error message stating that a driver failed
initialization. Use addr, which contains the correct address
for each tuner.

Fixes: ad32495b1513 ("media: em28xx-dvb: simplify DVB module probing logic")

Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: videobuf-dma-sg: Fix dma_{sync,unmap}_sg() calls

This reverts commit fc7f8fd42c2b934ac348995e0c530c917fc277d5.

Whilst the rationale for the above commit was in general correct, i.e.
that users *consuming* the DMA addresses should rely on sglen rather
than num_pages, it has always been the case that the DMA API itself
still requires that dma_{sync,unmap}_sg() are called with the original
number of entries as passed to dma_map_sg(), not the number of mapped
entries it returned. Thus the particular changes made in that patch
were erroneous.

At worst this might lead to data loss at the tail end of mapped buffers
on non-coherent hardware, while at best it's an example of incorrect
DMA API usage which has proven to mislead readers.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: media/usbvision: fix spelling mistake: "compresion" -> "compression"

Trivial fix to spelling mistake in proc text string

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: coda: set colorimetry on coded queue

Do not set context colorimetry on the raw (OUTPUT) queue for encoders.
Always set colorimetry on the coded queue (CAPTURE for encoders, OUTPUT
for decoders).
This also skips propagation of capture queue format and selection
rectangle on S_FMT(OUTPUT) to the CAPTURE queue for encoders.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: coda: do not try to propagate format if capture queue busy

The driver helpfully resets the capture queue format and selection
rectangle whenever output format is changed. This only works while
the capture queue is not busy.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: coda: reuse coda_s_fmt_vid_cap to propagate format in coda_s_fmt_vid_out

Instead of duplicating the same code, call into coda_s_fmt_vid_out to
propagate the output format to the capture queue.

Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: sta2x11: Use gpio_is_valid() and remove unnecessary check

Replace the manual validity checks for the GPIO with the
gpio_is_valid().

In vip_gpio_reserve(), Error checking for gpio pin is not correct.
If pwr_pin = -1, It will return 0. This should be return an error.

In sta2x11_vip_init_one(), Error checking for gpio 'reset_pin'
is unnecessary. Because vip_gpio_reserve() is also checking for
valid gpio pin. So removed extra error checking for gpio 'reset_pin'.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: platform: Use gpio_is_valid()

Replace the manual validity checks for the GPIO with the
gpio_is_valid().

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>

media: v4l2-dev.h: fix doc warning

Fix this warning when building the docs:

include/media/v4l2-dev.h:42: warning: Enum value 'VFL_TYPE_MAX' not described in enum 'vfl_devnode_type'

Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>