Merge branch 'wireless-2.6' of git://git./linux/kernel/git/iwlwifi/iwlwifi-2.6

p54pci: update receive dma buffers before and after processing

Documentation/DMA-API-HOWTO.txt states:

"DMA transfers need to be synced properly in order for
the cpu and device to see the most uptodate and correct
copy of the DMA buffer."

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

fix cfg80211_wext_siwfreq lock ordering...

I previously managed to reproduce a hang while scanning wireless
channels (reproducible with airodump-ng hopping channels); subsequent
lockdep instrumentation revealed a lock ordering issue.

Without knowing the design intent, it looks like the locks should be
taken in reverse order; please comment.

=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.38-rc5-341cd #4
-------------------------------------------------------
airodump-ng/15445 is trying to acquire lock:
 (&rdev->devlist_mtx){+.+.+.}, at: [<ffffffff816b1266>]
cfg80211_wext_siwfreq+0xc6/0x100

but task is already holding lock:
 (&wdev->mtx){+.+.+.}, at: [<ffffffff816b125c>] cfg80211_wext_siwfreq+0xbc/0x100

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #1 (&wdev->mtx){+.+.+.}:
       [<ffffffff810a79d6>] lock_acquire+0xc6/0x280
       [<ffffffff816d6bce>] mutex_lock_nested+0x6e/0x4b0
       [<ffffffff81696080>] cfg80211_netdev_notifier_call+0x430/0x5f0
       [<ffffffff8109351b>] notifier_call_chain+0x8b/0x100
       [<ffffffff810935b1>] raw_notifier_call_chain+0x11/0x20
       [<ffffffff81576d92>] call_netdevice_notifiers+0x32/0x60
       [<ffffffff815771a4>] __dev_notify_flags+0x34/0x80
       [<ffffffff81577230>] dev_change_flags+0x40/0x70
       [<ffffffff8158587c>] do_setlink+0x1fc/0x8d0
       [<ffffffff81586042>] rtnl_setlink+0xf2/0x140
       [<ffffffff81586923>] rtnetlink_rcv_msg+0x163/0x270
       [<ffffffff8159d741>] netlink_rcv_skb+0xa1/0xd0
       [<ffffffff815867b0>] rtnetlink_rcv+0x20/0x30
       [<ffffffff8159d39a>] netlink_unicast+0x2ba/0x300
       [<ffffffff8159dd57>] netlink_sendmsg+0x267/0x3e0
       [<ffffffff8155e364>] sock_sendmsg+0xe4/0x110
       [<ffffffff8155f3a3>] sys_sendmsg+0x253/0x3b0
       [<ffffffff81003192>] system_call_fastpath+0x16/0x1b

-> #0 (&rdev->devlist_mtx){+.+.+.}:
       [<ffffffff810a7222>] __lock_acquire+0x1622/0x1d10
       [<ffffffff810a79d6>] lock_acquire+0xc6/0x280
       [<ffffffff816d6bce>] mutex_lock_nested+0x6e/0x4b0
       [<ffffffff816b1266>] cfg80211_wext_siwfreq+0xc6/0x100
       [<ffffffff816b2fad>] ioctl_standard_call+0x5d/0xd0
       [<ffffffff816b3223>] T.808+0x163/0x170
       [<ffffffff816b326a>] wext_handle_ioctl+0x3a/0x90
       [<ffffffff815798d2>] dev_ioctl+0x6f2/0x830
       [<ffffffff8155cf3d>] sock_ioctl+0xfd/0x290
       [<ffffffff8117dffd>] do_vfs_ioctl+0x9d/0x590
       [<ffffffff8117e53a>] sys_ioctl+0x4a/0x80
       [<ffffffff81003192>] system_call_fastpath+0x16/0x1b

other info that might help us debug this:

2 locks held by airodump-ng/15445:
 #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81586782>] rtnl_lock+0x12/0x20
 #1:  (&wdev->mtx){+.+.+.}, at: [<ffffffff816b125c>]
cfg80211_wext_siwfreq+0xbc/0x100

stack backtrace:
Pid: 15445, comm: airodump-ng Not tainted 2.6.38-rc5-341cd #4
Call Trace:
 [<ffffffff810a3f0a>] ? print_circular_bug+0xfa/0x100
 [<ffffffff810a7222>] ? __lock_acquire+0x1622/0x1d10
 [<ffffffff810a1f99>] ? trace_hardirqs_off_caller+0x29/0xc0
 [<ffffffff810a79d6>] ? lock_acquire+0xc6/0x280
 [<ffffffff816b1266>] ? cfg80211_wext_siwfreq+0xc6/0x100
 [<ffffffff810a31d7>] ? mark_held_locks+0x67/0x90
 [<ffffffff816d6bce>] ? mutex_lock_nested+0x6e/0x4b0
 [<ffffffff816b1266>] ? cfg80211_wext_siwfreq+0xc6/0x100
 [<ffffffff810a31d7>] ? mark_held_locks+0x67/0x90
 [<ffffffff816b1266>] ? cfg80211_wext_siwfreq+0xc6/0x100
 [<ffffffff816b1266>] ? cfg80211_wext_siwfreq+0xc6/0x100
 [<ffffffff816b2fad>] ? ioctl_standard_call+0x5d/0xd0
 [<ffffffff8157818b>] ? __dev_get_by_name+0x9b/0xc0
 [<ffffffff816b2f50>] ? ioctl_standard_call+0x0/0xd0
 [<ffffffff816b3223>] ? T.808+0x163/0x170
 [<ffffffff8112ddf2>] ? might_fault+0x72/0xd0
 [<ffffffff816b326a>] ? wext_handle_ioctl+0x3a/0x90
 [<ffffffff8112de3b>] ? might_fault+0xbb/0xd0
 [<ffffffff815798d2>] ? dev_ioctl+0x6f2/0x830
 [<ffffffff810a1bae>] ? put_lock_stats+0xe/0x40
 [<ffffffff810a1c8c>] ? lock_release_holdtime+0xac/0x150
 [<ffffffff8155cf3d>] ? sock_ioctl+0xfd/0x290
 [<ffffffff8117dffd>] ? do_vfs_ioctl+0x9d/0x590
 [<ffffffff8116c8ff>] ? fget_light+0x1df/0x3c0
 [<ffffffff8117e53a>] ? sys_ioctl+0x4a/0x80
 [<ffffffff81003192>] ? system_call_fastpath+0x16/0x1b

Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Fix WPA TKIP Michael MIC failures.

As reported and found by Johannes Stezenbach:
rt2800{pci,usb} do not report the Michael MIC in RXed frames, but do check
the Michael MIC in hardware. Therefore we have to report to mac80211 that the
received frame does not include the Michael MIC.

https://bugzilla.kernel.org/show_bug.cgi?id=16608

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: Support new 5000 microcode.

New iwlwifi-5000 microcode requires driver support for API version 5.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>

ath5k: Fix fast channel switching

Fast channel change fixes:

a) Always set OFDM timings
b) Don't re-activate PHY
c) Enable only NF calibration, not AGC

https://bugzilla.kernel.org/show_bug.cgi?id=27382

Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: Correct channel setting for AR2317 chip

Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.

Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless: rt2x00: rt2800pci.c: add two ids

taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217

Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix conn_mon_timer running after disassociate

Low level driver could pass rx frames to us after disassociate, what
can lead to run conn_mon_timer by ieee80211_sta_rx_notify(). That
is obviously wrong, but nothing happens until we unload modules and
resources are used after free. If kernel debugging is enabled following
warning could be observed:

WARNING: at lib/debugobjects.c:259 debug_print_object+0x65/0x70()
Hardware name: HP xw8600 Workstation
ODEBUG: free active (active state 0) object type: timer_list
Modules linked in: iwlagn(-) iwlcore mac80211 cfg80211 aes_x86_64 aes_generic fuse cpufreq_ondemand acpi_cpufreq freq_table mperf xt_physdev ipt_REJECT nf_conntrack_ipv4 nf_defrag_ipv4 iptable_filter ip_tables ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 xt_state nf_conntrack ip6table_filter ip6_tables ipv6 ext3 jbd dm_mirror dm_region_hash dm_log dm_mod uinput hp_wmi sparse_keymap sg wmi arc4 microcode serio_raw ecb tg3 shpchp rfkill ext4 mbcache jbd2 sr_mod cdrom sd_mod crc_t10dif firewire_ohci firewire_core crc_itu_t mptsas mptscsih mptbase scsi_transport_sas ahci libahci pata_acpi ata_generic ata_piix floppy nouveau ttm drm_kms_helper drm i2c_algo_bit i2c_core video [last unloaded: cfg80211]
Pid: 13827, comm: rmmod Tainted: G        W   2.6.38-rc4-wl+ #22
Call Trace:
 [<ffffffff810649cf>] ? warn_slowpath_common+0x7f/0xc0
 [<ffffffff81064ac6>] ? warn_slowpath_fmt+0x46/0x50
 [<ffffffff81226fc5>] ? debug_print_object+0x65/0x70
 [<ffffffff81227625>] ? debug_check_no_obj_freed+0x125/0x210
 [<ffffffff8109ebd7>] ? debug_check_no_locks_freed+0xf7/0x170
 [<ffffffff81156092>] ? kfree+0xc2/0x2f0
 [<ffffffff813ec5c5>] ? netdev_release+0x45/0x60
 [<ffffffff812f1067>] ? device_release+0x27/0xa0
 [<ffffffff81216ddd>] ? kobject_release+0x8d/0x1a0
 [<ffffffff81216d50>] ? kobject_release+0x0/0x1a0
 [<ffffffff812183b7>] ? kref_put+0x37/0x70
 [<ffffffff81216c57>] ? kobject_put+0x27/0x60
 [<ffffffff813d5d1b>] ? netdev_run_todo+0x1ab/0x270
 [<ffffffff813e771e>] ? rtnl_unlock+0xe/0x10
 [<ffffffffa0581188>] ? ieee80211_unregister_hw+0x58/0x120 [mac80211]
 [<ffffffffa0377ed7>] ? iwl_pci_remove+0xdb/0x22a [iwlagn]
 [<ffffffff8123cde2>] ? pci_device_remove+0x52/0x120
 [<ffffffff812f5205>] ? __device_release_driver+0x75/0xe0
 [<ffffffff812f5348>] ? driver_detach+0xd8/0xe0
 [<ffffffff812f4111>] ? bus_remove_driver+0x91/0x100
 [<ffffffff812f5b62>] ? driver_unregister+0x62/0xa0
 [<ffffffff8123d194>] ? pci_unregister_driver+0x44/0xa0
 [<ffffffffa0377df5>] ? iwl_exit+0x15/0x1c [iwlagn]
 [<ffffffff810ab492>] ? sys_delete_module+0x1a2/0x270
 [<ffffffff81498889>] ? trace_hardirqs_on_thunk+0x3a/0x3f
 [<ffffffff8100bf42>] ? system_call_fastpath+0x16/0x1b

Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-2.6

Bluetooth: Add Atheros BT AR5BBU12 fw supported

Add the btusb.c blacklist [0489:e02c] for Atheros AR5BBU12 BT
and add to ath3k.c supported this device.

Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Release BTM while sleeping to avoid deadlock

Signed-off-by: Vladislav P <vladisslav@inbox.ru>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: fix crash with quirky dongles doing sound

Quirky dongles sometimes do not use the iso interface which
causes a crash with runtime PM

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

ath9k: Fix ath9k prevents CPU to enter C3 states

The DMA latency issue is observed only in Intel pinetrail platforms
but in the driver we had a default PM-QOS value of 55. This caused
unnecessary power consumption and battery drain in other platforms.

Remove the pm-qos thing in the driver code and address the throughput
issue in Intel pinetrail platfroms in user space using any one of
the scripts in below links:

http://www.kernel.org/pub/linux/kernel/people/mcgrof/scripts/cpudmalatency.c
http://johannes.sipsolutions.net/files/netlatency.c.txt

More details can be found in the following bugzilla link:

https://bugzilla.kernel.org/show_bug.cgi?id=27532

This reverts the following commits:

98c316e348bedffa730e6f1e4baeb8a3c3e0f28b
4dc3530df7c0428b41c00399a7ee8c929406d181
10598c124ecabbbfd7522f74de19b8f7d52a1bee

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing locking in ieee80211_reconfig

When suspending an associated system, and then resuming,
the station vif is being reconfigured without taking the
sdata->u.mgd.mtx lock, which results in the following warning:

WARNING: at net/mac80211/mlme.c:101 ieee80211_ap_probereq_get+0x58/0xb8 [mac80211]()
Modules linked in: wl12xx_sdio wl12xx firmware_class crc7 mac80211 cfg80211 [last unloaded: crc7]
Backtrace:
[<c005432c>] (dump_backtrace+0x0/0x118) from [<c0376e28>] (dump_stack+0x20/0x24)
 r7:00000000 r6:bf12d6ec r5:bf154aac r4:00000065
[<c0376e08>] (dump_stack+0x0/0x24) from [<c0079104>] (warn_slowpath_common+0x5c/0x74)
[<c00790a8>] (warn_slowpath_common+0x0/0x74) from [<c0079148>] (warn_slowpath_null+0x2c/0x34)
 r9:000024ff r8:cd006460 r7:00000001 r6:00000000 r5:00000000
r4:cf1394a0
[<c007911c>] (warn_slowpath_null+0x0/0x34) from [<bf12d6ec>] (ieee80211_ap_probereq_get+0x58/0xb8 [mac80211])
[<bf12d694>] (ieee80211_ap_probereq_get+0x0/0xb8 [mac80211]) from [<bf19cd04>] (wl1271_cmd_build_ap_probe_req+0x30/0xf8 [wl12xx])
 r4:cd007440
[<bf19ccd4>] (wl1271_cmd_build_ap_probe_req+0x0/0xf8 [wl12xx]) from [<bf1995f4>] (wl1271_op_bss_info_changed+0x4c4/0x808 [wl12xx])
 r5:cd007440 r4:000003b4
[<bf199130>] (wl1271_op_bss_info_changed+0x0/0x808 [wl12xx]) from [<bf122168>] (ieee80211_bss_info_change_notify+0x1a4/0x1f8 [mac80211])
[<bf121fc4>] (ieee80211_bss_info_change_notify+0x0/0x1f8 [mac80211]) from [<bf141e80>] (ieee80211_reconfig+0x4d0/0x668 [mac80211])
 r8:cf0eeea4 r7:cd00671c r6:00000000 r5:cd006460 r4:cf1394a0
[<bf1419b0>] (ieee80211_reconfig+0x0/0x668 [mac80211]) from [<bf137dd4>] (ieee80211_resume+0x60/0x70 [mac80211])
[<bf137d74>] (ieee80211_resume+0x0/0x70 [mac80211]) from [<bf0eb930>] (wiphy_resume+0x6c/0x7c [cfg80211])
 r5:cd006248 r4:cd006110
[<bf0eb8c4>] (wiphy_resume+0x0/0x7c [cfg80211]) from [<c0241024>] (legacy_resume+0x38/0x70)
 r7:00000000 r6:00000000 r5:cd006248 r4:cd0062fc
[<c0240fec>] (legacy_resume+0x0/0x70) from [<c0241478>] (device_resume+0x168/0x1a0)
 r8:c04ca8d8 r7:cd00627c r6:00000010 r5:cd006248 r4:cd0062fc
[<c0241310>] (device_resume+0x0/0x1a0) from [<c0241600>] (dpm_resume_end+0xf8/0x3bc)
 r7:00000000 r6:00000005 r5:cd006248 r4:cd0062fc
[<c0241508>] (dpm_resume_end+0x0/0x3bc) from [<c00b2a24>] (suspend_devices_and_enter+0x1b0/0x204)
[<c00b2874>] (suspend_devices_and_enter+0x0/0x204) from [<c00b2b68>] (enter_state+0xf0/0x148)
 r7:c037e978 r6:00000003 r5:c043d807 r4:00000000
[<c00b2a78>] (enter_state+0x0/0x148) from [<c00b20a4>] (state_store+0xa4/0xcc)
 r7:c037e978 r6:00000003 r5:00000003 r4:c043d807
[<c00b2000>] (state_store+0x0/0xcc) from [<c01fc90c>] (kobj_attr_store+0x20/0x24)
[<c01fc8ec>] (kobj_attr_store+0x0/0x24) from [<c0157120>] (sysfs_write_file+0x11c/0x150)
[<c0157004>] (sysfs_write_file+0x0/0x150) from [<c0100f84>] (vfs_write+0xc0/0x14c)
[<c0100ec4>] (vfs_write+0x0/0x14c) from [<c01010e4>] (sys_write+0x4c/0x78)
 r8:40126000 r7:00000004 r6:cf1a7c80 r5:00000000 r4:00000000
[<c0101098>] (sys_write+0x0/0x78) from [<c00500c0>] (ret_fast_syscall+0x0/0x30)
 r8:c00502c8 r7:00000004 r6:403525e8 r5:40126000 r4:00000004

Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwl3945: remove plcp check

Patch fixes:
https://bugzilla.redhat.com/show_bug.cgi?id=654599

Many users report very low speed problem on 3945 devices,
this patch fixes problem, but only for some of them.

For unknown reason, sometimes after hw scanning, device is not able
to receive frames at high rate. Since plcp health check may request
hw scan to "reset radio", performance problem start to be observable
after update kernel to .35, where plcp check was introduced.

Bug reporter confirmed that removing plcp check fixed problem for him.

Reported-and-tested-by: SilvioTO <silviotoya@yahoo.it>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge branch 'master' of git://git./linux/kernel/git/padovan/bluetooth-2.6

mac80211: fix the skb cloned check in the tx path

Using skb_header_cloned to check if it's safe to write to the skb is not
enough - mac80211 also touches the tailroom of the skb.
Initially this check was only used to increase a counter, however this
commit changed the code to also skip skb data reallocation if no extra
head/tailroom was needed:

commit 4cd06a344db752f513437138953af191cbe9a691
mac80211: skip unnecessary pskb_expand_head calls

It added a regression at least with iwl3945, which is fixed by this patch.

Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: Re-enable RF_KILL interrupt when down

With commit 554d1d027b19265c4aa3f718b3126d2b86e09a08 only one RF_KILL
interrupt will be seen by the driver when the interface is down.

Re-enable the interrupt when it occurs to see all transitions.

Signed-off-by: Don Fry <donald.h.fry@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb-pcmcia: Fix parsing of invariants tuples

This fixes parsing of the device invariants (MAC address)
for PCMCIA SSB devices.

ssb_pcmcia_do_get_invariants expects an iv pointer as data
argument.

Tested-by: dylan cristiani <d.cristiani@idem-tech.it>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix possible double free of PAPRD skb's

This patch reverts the following commit
ath9k: remove bfs_paprd_timestamp from struct ath_buf_state

Under high interference/noisy environment conditions where PAPRD frames
fails heavily introduces a possibility of double freeing skb's and causes
kernel panic after some time.This patch reverts back to the original approach
of using paprd_timestamp before freeing the PAPRD frame skb's

[  194.193705] Pid: 0, comm: swapper Tainted: G      D WC
2.6.35-22-generic #33-Ubuntu
[  194.193712] Call Trace:
[  194.193722]  [<c05c6468>] ? printk+0x2d/0x35
[  194.193732]  [<c05c63c3>] panic+0x5a/0xd2
[  194.193741]  [<c05ca3ed>] oops_end+0xcd/0xd0
[  194.193750]  [<c0105f74>] die+0x54/0x80
[  194.193758]  [<c05c9a16>] do_trap+0x96/0xc0
[  194.193837]  [<c0103fb0>] ? do_invalid_op+0x0/0xa0
[  194.193846]  [<c010403b>] do_invalid_op+0x8b/0xa0
[  194.193856]  [<c020bd4c>] ? kfree+0xec/0xf0
[  194.193866]  [<c012ce18>] ? default_spin_lock_flags+0x8/0x10
[  194.193877]  [<c01de47a>] ? free_one_page+0x12a/0x2d0
[  194.193888]  [<c01e04dc>] ? __free_pages+0x1c/0x40
[  194.193897]  [<c05c97a7>] error_code+0x73/0x78
[  194.193906]  [<c020bd4c>] ? kfree+0xec/0xf0
[  194.193915]  [<c04ecdd0>] ? skb_release_data+0x70/0xa0
[  194.193924]  [<c04ecdd0>] skb_release_data+0x70/0xa0
[  194.193933]  [<c04ec997>] __kfree_skb+0x17/0x90
[  194.193941]  [<c04eca31>] consume_skb+0x21/0x40
[  194.193964]  [<f85e0b70>] ieee80211_tx_status+0x760/0x860 [mac80211]
[  194.193979]  [<f85caddf>] ath_tx_complete_buf+0x1bf/0x2c0 [ath9k]
[  194.193988]  [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[  194.193997]  [<c04ec40e>] ? skb_queue_tail+0x3e/0x50
[  194.194010]  [<f85cc803>] ath_tx_complete_aggr+0x823/0x940 [ath9k]
[  194.194021]  [<c0108a28>] ? sched_clock+0x8/0x10
[  194.194030]  [<c016bf14>] ? sched_clock_local+0xa4/0x180
[  194.194040]  [<c0139f57>] ? enqueue_sleeper+0x1e7/0x2b0
[  194.194051]  [<c013a194>] ? enqueue_entity+0x174/0x200
[  194.194064]  [<f85ce83d>] ath_tx_edma_tasklet+0x2bd/0x3b0 [ath9k]
[  194.194074]  [<c05c8b9f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[  194.194088]  [<f85c7b9f>] ath9k_tasklet+0x9f/0x190 [ath9k]
[  194.194097]  [<c01505d7>] tasklet_action+0xa7/0xb0
[  194.194107]  [<c015127c>] __do_softirq+0x9c/0x1b0
[  194.194117]  [<c01a7f64>] ? irq_to_desc+0x14/0x20
[  194.194126]  [<c0124fc4>] ? ack_apic_level+0x64/0x1f0
[  194.194136]  [<c01513d5>] do_softirq+0x45/0x50
[  194.194145]  [<c0151545>] irq_exit+0x65/0x70
[  194.194153]  [<c05cf665>] do_IRQ+0x55/0xc0
[  194.194162]  [<c016a6c7>] ? hrtimer_start+0x27/0x30
[  194.194171]  [<c0103630>] common_interrupt+0x30/0x38
[  194.194181]  [<c012c21a>] ? native_safe_halt+0xa/0x10
[  194.194268]  [<c010a2f9>] default_idle+0x49/0xb0
[  194.194277]  [<c0101fcc>] cpu_idle+0x8c/0xd0
[  194.194286]  [<c05b2431>] rest_init+0x71/0x80
[  194.194295]  [<c081981a>] start_kernel+0x36e/0x374
[  194.194305]  [<c08199dd>] ? pass_all_bootoptions+0x0/0xa
[  194.194314]  [<c08190d7>] i386_start_kernel+0xd7/0xdf
[  194.194364] panic occurred, switching back to text console

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

carl9170: fix typo in PS code

This patch fixes a off-by-one bug which bugged
the driver's PS-POLL capability.

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wireless, wl1251: Fix potential NULL pointer dereference in wl1251_op_bss_info_changed()

In drivers/net/wireless/wl1251/main.c:wl1251_op_bss_info_changed() we make
a call to ieee80211_beacon_get() which may return NULL, but we do not
check the return value before dereferencing the pointer.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix TX status cookie in HW offload case

When the off-channel TX is done with remain-on-channel
offloaded to hardware, the reported cookie is wrong as
in that case we shouldn't use the SKB as the cookie but
need to instead use the corresponding r-o-c cookie
(XOR'ed with 2 to prevent API mismatches).

Fix this by keeping track of the hw_roc_skb pointer
just for the status processing and use the correct
cookie to report in this case. We can't use the
hw_roc_skb pointer itself because it is NULL'ed when
the frame is transmitted to prevent it being used
twice.

This fixes a bug where the P2P state machine in the
supplicant gets stuck because it never gets a correct
result for its transmitted frame.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlagn: overwrite EEPROM chain setting for 6250 devices

6250 2x2 devices have 2 tx chain and 2 rx chain. For some reason,
the EEPROM contain incorrect information and indicate it only has single
tx chain. overwrite it with .cfg parameter to make sure both chain 'A' and
chain 'B' can be used for transmit and receive

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Set conn state to BT_DISCONN to avoid multiple responses

This patch fixes a minor issue that two connection responses will be sent
for one L2CAP connection request. If the L2CAP connection request is first
blocked due to security reason and responded with reason "security block",
the state of the connection remains BT_CONNECT2. If a pairing procedure
completes successfully before the ACL connection is down, local host will
send another connection complete response. See the following packets
captured by hcidump.

2010-12-07 22:21:24.928096 < ACL data: handle 12 flags 0x00 dlen 16
    0000: 0c 00 01 00 03 19 08 00  41 00 53 00 03 00 00 00  ........A.S.....
... ...

2010-12-07 22:21:35.791747 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 12
... ...

2010-12-07 22:21:35.872372 > ACL data: handle 12 flags 0x02 dlen 16
    L2CAP(s): Connect rsp: dcid 0x0054 scid 0x0040 result 0 status 0
      Connection successful

Signed-off-by: Liang Bao <tim.bao@gmail.com>
Acked-by: Ville Tervo <ville.tervo@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

ath9k: Fix memory leak due to failed PAPRD frames

free the skb's when the Tx of PAPRD frames fails and also add a debug
message indicating that.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

wl12xx: fix use after free

When DEBUG_SPI is included in the debug log level wl1271_spi_reset()
will dump the already freed memory instead of the SPI buffer.

This bug was spotted by the semantic patch tool coccinelle using the
script found at scripts/coccinelle/free/kfree.cocci.

More information about semantic patching is available at
http://coccinelle.lip6.fr/

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: Fix power save usage count imbalance on deinit

While unloading the driver, the ps_usecount is incremented
before configuring gpio registers in deinit_device.
But it is failed to restore the ps_usecount after that.
The problem is that the chip is forcibly moved to FULL SLEEP
by radio_disable when mac80211 is reporting as idle
though ps_usecount is not zero.

This patch retores ps_usecount properly and ensures that
the chip is always moved to full sleep only if ps usage
count is zero which also helps in debugging deadbeef on
multivif case. And also fixes the following warning.

ath: DMA failed to stop in 10 ms AR_CR=0xdeadbeef AR_DIAG_SW=0xdeadbeef
ath: Could not stop RX, we could be confusing the DMA engine when we
start RX up
------------[ cut here ]------------
WARNING: at drivers/net/wireless/ath/ath9k/recv.c:536
ath_stoprecv+0xf4/0x100 [ath9k]()

Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix system hang when resuming from S3/S4

The bit 6 & 7 of AR_WA (0x4004) should be enabled only
for the chips that are supporting L0s functionality
while resuming back from S3/S4.

Enabling these bits for AR9280 is causing system hang
within a few S3/S4-resume cycles.

Cc: stable@kernel.org
Cc: Jack Lee <jlee@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

MAINTAINERS: update information for the wl12xx driver

Update maintainer's email address, webpage and align with renaming of
files.

Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: fix race conditions when stop device

We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Disable interrupts, kill tasklets
and then works in correct order.

Cc: stable@kernel.org
Tested-by: Sujith <m.sujith@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: fix race conditions when stop device

We do not kill any scheduled tasklets when stopping device, that may
cause usage of resources after free. Moreover we enable interrupts
in tasklet function, so we could potentially end with interrupts
enabled when driver is not ready to receive them.

I think patch should fix Ben's kernel crash from:
http://marc.info/?l=linux-wireless&m=129438358921501&w=2

Cc: stable@kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: correct endianness of frame duration

The ath5k version of ieee80211_generic_frame_duration() returns
an __le16 for standard modes but a cpu-endian int for turbo/half/
quarter rates.  Make it always return cpu-endian values.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: fix error handling in ath5k_hw_dma_stop

Review spotted a problem with the error handling in ath5k_hw_dma_stop:
a successful return from ath5k_hw_stop_tx_dma will be treated as
an error, so we always bail out of the loop after processing a single
active queue.  As a result, we may not actually stop some queues during
reset.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix firmware upload errors

When the source code from Realtek was prepared for kernel inclusion,
some routines were refactored to reduce the level of indentation. This
patch repairs errors introduced in that process.

Signed-off-by: Chaoming Li <chaoming_li@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: add Atheros BT AR9285 fw supported

Add the btusb.c blacklist [03f0:311d] for Atheros AR9285 Malbec BT
and add to ath3k.c ath3-1.fw (md5:1211fa34c09e10ba48381586b7c3883d)
supported this device.

Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

MAINTAINERS: remove Reinette Chatre as iwlwifi maintainer

Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: add device id for windy31 usb device

This patch adds the device id for the windy31 USB device to the rt73usb
driver.

Thanks to Ralf Flaxa for reporting this and providing testing and a
sample device.

Reported-by: Ralf Flaxa <rf@suse.de>
Tested-by: Ralf Flaxa <rf@suse.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix a crash in ieee80211_beacon_get_tim on change_interface

Some drivers (e.g. ath9k) do not always disable beacons when they're
supposed to. When an interface is changed using the change_interface op,
the mode specific sdata part is in an undefined state and trying to
get a beacon at this point can produce weird crashes.

To fix this, add a check for ieee80211_sdata_running before using
anything from the sdata.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rtlwifi: Fix possible NULL dereference

In drivers/net/wireless/rtlwifi/pci.c::_rtl_pci_rx_interrupt() we call
dev_alloc_skb(), which may fail and return NULL, but we do not check the
returned value against NULL before dereferencing the returned pointer.
This may lead to a NULL pointer dereference which means we'll crash - not
good.

In a separate call to dev_alloc_skb(), the debug level is changed so that
the failure message will always be logged.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k: add missing ps wakeup/restore calls

There are several places where ath_reset() was called without proper
calls to ath9k_ps_wakeup/ath9k_ps_restore. To fix this, add those calls
directly to ath_reset and drop them from callers where it makes sense.

Also add them to the config callback around ath_update_txpow to fix a
crash that happens when the tx power changed before any vif is brought up.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: disabled PAPRD for AR9003

AR9003's PAPRD was enabled prematurely, and is causing some
large discrepancies on throughput and network connectivity.
For example downlink (RX) throughput against an AR9280 AP
can vary widlely from 43-73 Mbit/s while disabling this
gets AR9382 (2x2) up to around 93 Mbit/s in a 2.4 GHz HT20 setup.

Cc: stable@kernel.org
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwlwifi: don't read sku information from EEPROM for 4965

For all the new devices, the sku information should read from EEPROM
but for legacy devices such as 4965, appearly the EEPROM does not
contain the necessary information. so skip the read from EEPROM
and go back to use software configuration.

Reported-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Bluetooth: Fix race condition with conn->sec_level

The conn->sec_level value is supposed to represent the current level of
security that the connection has. However, by assigning to it before
requesting authentication it will have the wrong value during the
authentication procedure. To fix this a pending_sec_level variable is
added which is used to track the desired security level while making
sure that sec_level always represents the current level of security.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix authentication request for L2CAP raw sockets

When there is an existing connection l2cap_check_security needs to be
called to ensure that the security level of the new socket is fulfilled.
Normally l2cap_do_start takes care of this, but that function doesn't
get called for SOCK_RAW type sockets. This patch adds the necessary
l2cap_check_security call to the appropriate branch in l2cap_do_connect.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Create a unified auth_type evaluation function

The logic for determining the needed auth_type for an L2CAP socket is
rather complicated and has so far been duplicated in
l2cap_check_security as well as l2cap_do_connect. Additionally the
l2cap_check_security code was completely missing the handling of
SOCK_RAW type sockets. This patch creates a unified function for the
evaluation and makes l2cap_do_connect and l2cap_check_security use that
function.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix MITM protection requirement preservation

If an existing connection has a MITM protection requirement (the first
bit of the auth_type) then that requirement should not be cleared by new
sockets that reuse the ACL but don't have that requirement.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Revert "Bluetooth: Update sec_level/auth_type for already existing connections"

This reverts commit 045309820afe047920a50de25634dab46a1e851d. That
commit is wrong for two reasons:

- The conn->sec_level shouldn't be updated without performing
authentication first (as it's supposed to represent the level of
security that the existing connection has)

- A higher auth_type value doesn't mean "more secure" like the commit
seems to assume. E.g. dedicated bonding with MITM protection is 0x03
whereas general bonding without MITM protection is 0x04. hci_conn_auth
already takes care of updating conn->auth_type so hci_connect doesn't
need to do it.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Never deallocate a session when some DLC points to it

Fix a bug introduced in commit 9cf5b0ea3a7f1432c61029f7aaf4b8b338628884:
function rfcomm_recv_ua calls rfcomm_session_put without checking that
the session is not referenced by some DLC. If the session is freed, that
DLC would refer to deallocated memory, causing an oops later, as shown
in this bug report: https://bugzilla.kernel.org/show_bug.cgi?id=15994

Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: Fix leaking blacklist when unregistering a hci device

The blacklist should be freed before the hci device gets unregistered.

Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: l2cap: fix misuse of logical operation in place of bitop

CC: Marcel Holtmann <marcel@holtmann.org>
CC: "Gustavo F. Padovan" <padovan@profusion.mobi>
CC: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

Bluetooth: ath3k: reduce memory usage

There is no need to hold the firmware in memory.

Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>

iwlwifi: fix valid chain reading from EEPROM

When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath5k: fix locking in tx_complete_poll_work

ath5k_reset must be called with sc->lock.  Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.

Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: do PA offset calibration only on longcal interval

The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.

In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).

Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Fix endian issue in tx header

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: ASPM interoperability fix for AR9380/AR9382

There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.

Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: use maximum number of AMPDU frames as default in BA RX

When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes.  The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.

Thanks Johannes for helping me figure this one out.

Cc: stable@kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: fix lockdep warning

Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.

However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.

Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ieee80211: correct IEEE80211_ADDBA_PARAM_BUF_SIZE_MASK macro

It is defined in include/linux/ieee80211.h. As per IEEE spec.
bit6 to bit15 in block ack parameter represents buffer size.
So the bitmask should be 0xFFC0.

Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rt2x00: Don't leak mem in error path of rt2x00lib_request_firmware()

We need to release_firmware() in order not to leak memory.

Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

iwmc3200wifi: Return proper error for iwm_if_alloc

In the case of alloc_netdev_mq failure and kmalloc failure,
current implementation returns ERR_PTR(0).

As a result, the caller of iwm_if_alloc does not catch the error by IS_ERR
macro. Fix it by setting proper error code for ret variable in the failure
cases.

Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

hostap_cs: fix sleeping function called from invalid context

pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.

It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.

Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758

Reported-and-tested-by: rbugz@biobind.com
Cc: stable@kernel.org # 2.6.34+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ipw2200: Check for -1 INTA in tasklet too.

This is an attempt to fix a long standing open bug:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334

The interrupt handler checks for INTA being -1, apparently that means that the
hardware is gone. But the interrupt handler defers actual interrupt processing
to a tasklet. By the time the tasklet is run and checks INTA again, the
hardware might be gone and INTA be -1, which confuses the driver because all
event bits are set.

The patch applies to 2.6.37.

Signed-off-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ssb: Ignore dangling ethernet cores on wireless devices

Some Broadcom based wireless devices contain dangling ethernet cores.
This triggers the ssb probing mechanism and tries to load the b44 driver
on this core.
Ignore the dangling core in the ssb core scanning code to avoid
access to the core and failure of b44 probing.

Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

p54: fix sequence no. accounting off-by-one error

P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."

Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.

Yup, it's the exact opposite!

Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add doc short section on LED triggers

Just create a section to collect the LED trigger
functions and add a very short description as to
what drivers should do.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

nl80211: add/fix mesh docs

Some mesh attribute/command docs are missing or
have errors in the name so they don't match, fix
all of them.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

cfg80211: add mesh join/leave callback docs

When I made the patch to add mesh join/leave I
didn't pay attention to docs because it was a
proof of concept, and then when we actually did
merge it I forgot -- add docs now.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add missing docs for off-chan TX flag

The flag is IEEE80211_TX_CTL_TX_OFFCHAN and I had
added that in a previous patch but forgotten docs.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_htc: Really fix packet injection

The chainmask value along with other configuration has to be set
on the target for packet injection. Fix this and also move the monitor
interface addition before the channel set segment to ensure that
the opmode is updated properly.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211: add remain-on-channel docs

Add documentation for the new callbacks that I
forgot in the patch adding the callbacks.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix RX handling for USB devices

Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset"
uncondionally added aborting RX DMA in a HW reset, though it is a bit
unclear as to why this is needed.

Anyway, RX DMA is handled in the target for USB devices, and this would
interfere with normal operations (scanning etc.), so fix this.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix thermal issue with UB94

Hardcode the output voltage of x-PA bias LDO to the lowest
value for UB94. The card doesn't get too hot now.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix calibration for AR9287 devices

AR9287 based devices have issues with ADC gain calibration
which would cause uplink throughput drops in HT40 mode.
Remove ADC gain from the supported calibration algorithms.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ath9k_hw: Fix chip test

USB devices do not require the chip test routine.

Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

ixgbe: update ntuple filter configuration

This change fixes several issues found in ntuple filtering while I was
doing the ATR refactor.

Specifically I updated the masks to work correctly with the latest version
of ethtool, I cleaned up the exception handling and added detailed error
output when a filter is rejected, and corrected several bits that were set
incorrectly in ixgbe_type.h.

The previous version of this patch included a printk that was left over from
me fixing the filter setup.  This patch does not include that printk.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: further flow director performance optimizations

This change adds a compressed input type for atr signature hash
computation.  It also drops the use of the set functions when setting up
the ATR input since we can then directly setup the hash input as two dwords
that can be stored and passed as registers.

With these changes the cost of computing the has is low enough that we can
perform a hash computation on each TCP SYN flagged packet allowing us to
drop the number of flow director misses considerably in tests such as
netperf TCP_CRR.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: cleanup flow director hash computation to improve performance

This change cleans up the layout of the flow director data, and the
algorithm used to calculate the hash resulting in a 35x / 3500% performance
increase versus the old flow director hash computation.  The overall effect
is only a 1% increase in transactions per second though due to the fact
that only 1 packet in 20 are actually hashed upon.

TCP_RR before:
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       60.00    23059.27
16384  87380

TCP_RR after:
Socket Size   Request  Resp.   Elapsed  Trans.
Send   Recv   Size     Size    Time     Rate
bytes  Bytes  bytes    bytes   secs.    per sec

16384  87380  1        1       60.00    23239.98
16384  87380

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: make sure per Rx queue is disabled before unmapping the receive buffer

When disable the Rx logic globally, we would also want to disable the per Rx
queue receive logic by per queue Rx control register RXDCTL so no more DMA is
happening from the packet buffer to the receive buffer associated with the Rx
ring, before we start unmapping Rx ring receive buffer. The hardware may take
max of 100us before the corresponding Rx queue is really disabled. Added
ixgbe_disable_rx_queue() for this purpose.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000: Add support for the CE4100 reference platform

This patch adds support for the gigabit phys present on the CE4100 reference
platforms.

Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: add custom set_d[0|3]_lplu_state function pointer for 82574

82574 needs to configure Low Power Link Up (or LPLU) differently than
the other parts in the 8257x family supported by the driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: power off PHY after reset when interface is down

Some Phys supported by the driver do not remain powered off across a reset
of the device when the interface is down, e.g. on 82571, but not on 82574.
This patch powers down (only when WoL is disabled) the PHY after a reset if
the interface is down and the ethtool diagnostics are not currently running.

The ethtool diagnostic function required a minor re-factor as a result, and
the e1000_[get|put]_hw_control() functions are renamed since they are no
longer static to netdev.c as they are needed by the ethtool diagnostics.
A couple minor whitespace issues were cleaned up, too.

Reported-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: use either_crc_le() rather than re-write it

For the 82579 jumbo frame workaround, there is no need to re-write the CRC
calculation functionality already found in the kernel's ether_crc_le().

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: properly bounds-check string functions

Use string functions with bounds checking rather than their non-bounds
checking counterparts, and do not hard code these boundaries.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: convert calls of ops.[read|write]_reg to e1e_[r|w]phy

Cleans up the code a bit by using the driver-specific e1e_rphy and
e1e_wphy macros instead of the full function pointer variants.  Fix
a couple whitespace issue with two already existing calls to e1e_wphy.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e1000e: cleanup variables set but not used

The ICR register is clear on read and we don't care what the returned value
is when resetting the hardware so the icr variable(s) can be removed.  We
should not ignore the return from e1000_lv_jumbo_workaround_ich8lan() and
from e1000_get_phy_id_82571() (dump a debug message when it fails and when
an unknown Phy id is returned).

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net offloading: Convert checksums to use centrally computed features.

In order to compute the features for other offloads (primarily
scatter/gather), we need to first check the ability of the NIC to
offload the checksum for the packet.  Since we have already computed
this, we can directly use the result instead of figuring it out
again.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net offloading: Convert skb_need_linearize() to use precomputed features.

This switches skb_need_linearize() to use the features that have
been centrally computed.  In doing so, this fixes a problem where
scatter/gather should not be used because the card does not support
checksum offloading on that type of packet.  On device registration
we only check that some form of checksum offloading is available if
scatter/gatther is enabled but we must also check at transmission
time.  Examples of this include IPv6 or vlan packets on a NIC that
only supports IPv4 offloading.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net offloading: Convert dev_gso_segment() to use precomputed features.

This switches dev_gso_segment() to use the device features computed
by the centralized routine.  In doing so, it fixes a problem where
it would always use dev->features, instead of those appropriate
to the number of vlan tags if any are present.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net offloading: Pass features into netif_needs_gso().

Now that there is a single function that can compute the device
features relevant to a packet, we don't want to run it for each
offload.  This converts netif_needs_gso() to take the features
of the device, rather than computing them itself.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net offloading: Generalize netif_get_vlan_features().

netif_get_vlan_features() is currently only used by netif_needs_gso(),
so it only concerns itself with GSO features.  However, several other
places also should take into account the contents of the packet when
deciding whether to offload to hardware.  This generalizes the function
to return features about all of the various forms of offloading.  Since
offloads tend to be linked together, this avoids duplicating the logic
in each location (i.e. the scatter/gather code also needs the checksum
logic).

Suggested-by: Michał Mirosław <mirqus@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net offloading: Accept NETIF_F_HW_CSUM for all protocols.

We currently only have software fallback for one type of checksum: the
TCP/UDP one's complement.  This means that a protocol that uses hardware
offloading for a different type of checksum (FCoE, SCTP) must directly
check the device's features and do the right thing ahead of time.  By
the time we get to dev_can_checksum(), we're only deciding whether to
apply the one algorithm in software or hardware.  NETIF_F_HW_CSUM has the
same capabilities as the software version, so we should always use it if
present.  The primary advantage of this is multiply tagged vlans can use
hardware checksumming.

Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

r8169: delay phy init until device opens.

It workarounds the 60s firmware load failure timeout for the
non-modular case.

Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: fix kernel-doc warning in core/filter.c

Fix new kernel-doc notation warning in net/core/filter.c:

Warning(net/core/filter.c:172): No description found for parameter 'fentry'
Warning(net/core/filter.c:172): Excess function parameter 'filter' description in 'sk_run_filter'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/sock.h: make some fields private to fix kernel-doc warning(s)

Fix new kernel-doc notation warning in sock.h by annotating skc_dontcopy_*
as private fields.

Warning(include/net/sock.h:163): No description found for parameter 'skc_dontcopy_end[0]'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netlink: test for all flags of the NLM_F_DUMP composite

Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.

Substitute the condition to test for _all_ bits being set.

Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

forcedeth: Do not use legacy PCI power management

The forcedeth driver uses the legacy PCI power management, so it has
to do PCI-specific things in its ->suspend() and ->resume() callbacks
and some of them are not done correctly.

Convert forcedeth to the new PCI power management framework and make
it let the PCI subsystem take care of all the PCI-specific aspects of
device handling during system power transitions.

Tested with nVidia Corporation MCP55 Ethernet (rev a2).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'dccp' of git://eden-feed.erg.abdn.ac.uk/net-next-2.6