Heinrich Schuchardt [Thu, 10 Jun 2021 21:10:52 +0000 (23:10 +0200)]
efi_loader: TPL_HIGH_LEVEL not allowed for CreateEvent
According to chapter 7.1 "Event, Timer, and Task Priority Services"
TPL_HIGH_LEVEL should not be exposed to applications and drivers.
According to the discussion with EDK II contributors this implies that
CreateEvent() shall not allow to create events with TPL_HIGH_LEVEL.
Cc: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Samer El-Haj-Mahmoud <Samer.El-Haj-Mahmoud@arm.com>
Tom Rini [Fri, 25 Jun 2021 17:33:47 +0000 (13:33 -0400)]
Merge tag 'u-boot-imx-
20210625' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
Fixes for 2021.07
-----------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7903
Tom Rini [Fri, 25 Jun 2021 01:18:22 +0000 (21:18 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-sh
- Beacon board fix, for this release.
Tom Rini [Fri, 25 Jun 2021 01:17:49 +0000 (21:17 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-usb
- A few easy MX7 EHCI USB fixes, for this release.
Fabio Estevam [Sun, 20 Jun 2021 15:00:52 +0000 (12:00 -0300)]
usb: ehci-mx6: Do not fail when 'reg' is not found
Unlike imx6, on imx7 the USB PHY is described as:
usbphynop1: usbphynop1 {
compatible = "usb-nop-xceiv";
clocks = <&clks IMX7D_USB_PHY1_CLK>;
clock-names = "main_clk";
#phy-cells = <0>;
};
which does not have the 'reg' property.
Do not return an error when the 'reg' property is not found
for the USB PHY.
This fixes USB gadget regression on a imx7s-warp board.
Successfully tested the "ums 0 mmc 0" command on two boards:
imx7s-warp and imx6dl-pico-pi.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Fabio Estevam [Sun, 20 Jun 2021 15:00:51 +0000 (12:00 -0300)]
usb: ehci-mx6: Move fdtdec_get_alias_seq() inside the CONFIG_MX6
On a imx7s-warp board the fdtdec_get_alias_seq() function
always fails.
As priv->portnr is only used on i.MX6, move fdtdec_get_alias_seq()
inside the CONFIG_MX6 block.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Adam Ford [Thu, 24 Jun 2021 17:52:11 +0000 (12:52 -0500)]
ARM: rmobile: beacon: Set CONFIG_RZ_G2 on Beacon boards
The board detection is incorrectly stating it's an rcar3 variant
instead of an RZ/G2 variant on all the r8a774*1_beacon boards.
Set the flag to correctly display as RZ/G2[M/N/H]
Signed-off-by: Adam Ford <aford173@gmail.com>
Tom Rini [Wed, 23 Jun 2021 12:46:26 +0000 (08:46 -0400)]
Merge https://source.denx.de/u-boot/custodians/u-boot-x86
- x86: Discard .note.gnu.property sections
- nvme: Skip block device creation for inactive namespaces
- nvme: Convert NVMe doc to reST, and various minor fixes
Tom Rini [Wed, 23 Jun 2021 12:45:29 +0000 (08:45 -0400)]
Merge tag 'mmc-2021-6-22' of https://source.denx.de/u-boot/custodians/u-boot-mmc
- Revert fsl_esdhc_imx using VENDORSPEC_FRC_SDCLK_ON
- Fix data read for dw_mmc
- Increase minimum bus freq for mtk-sd
- Minor cleanup
Tom Rini [Wed, 23 Jun 2021 12:45:09 +0000 (08:45 -0400)]
Merge branch '2021-06-22-assorted-fixes'
- Assorted minor bugfixes
Andy Shevchenko [Thu, 10 Jun 2021 15:08:42 +0000 (18:08 +0300)]
test: Include /sbin to the PATH when creating file system
On some distributions the mkfs is under /sbin and /sbin is not set
for mere users. Include /sbin to the PATH when creating file system,
so that users won't get a scary traceback from Python.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Jaehoon Chung [Mon, 14 Jun 2021 22:16:36 +0000 (07:16 +0900)]
MAINTAINER, git-mailrc: Update the mmc maintainer
Update to me as co-maintainer with Peng.
Additionally, update the mmc alias in git-mailrc.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Tom Rini [Thu, 3 Jun 2021 13:39:02 +0000 (09:39 -0400)]
global_data: Ensure we have <config.h> when symbols are not in Kconfig yet
All symbols that are defined in Kconfig will always be defined (or not)
prior to preprocessing due to the -include directive while building.
However, symbols which are not yet migrated will only be defined (or
not) once the board config.h is included, via <config.h>. While the end
goal must be to migrate all symbols, today we have cases where the size
of gd will get mismatched within the build, based on include order.
Mitigate this by making sure that any <asm/global_data.h> that uses
symbols not in Kconfig does start with <config.h>. Remove this when not
needed.
Cc: Alexey Brodkin <alexey.brodkin@synopsys.com>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Cc: Huan Wang <alison.wang@nxp.com>
Cc: Angelo Dureghello <angelo@sysam.it>
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 3 Jun 2021 13:39:01 +0000 (09:39 -0400)]
socfpga64: Do not define CONFIG_SYS_MEM_RESERVE_SECURE to 0
Based on the comment in socfpga_soc64_common.h, the intention is for
CONFIG_SYS_MEM_RESERVE_SECURE to be unused. However, in the code we do:
...
and that will evaluate to true. This leads to unwanted code being
compiled. Further, as CONFIG_SYS_MEM_RESERVE_SECURE has not been
migrated to Kconfig, this leads to a mismatch in the size of gd
depending on if we have or have not also had <configs/BOARD.h> also
included yet.
Remove the define as it's not needed.
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Chee Hong Ang <chee.hong.ang@intel.com>
Cc: Dalon Westergreen <dalon.westergreen@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 3 Jun 2021 13:39:00 +0000 (09:39 -0400)]
Revert "powerpc: fix regression in arch_initr_trap()"
With the changes in commit
588efcdd72fc ("powerpc: Don't use relative
include for config.h in global_data.h") fixing the root of the problem,
we no longer need this re-inclusion.
This reverts commit
f6c0d365d3e8ee8e4fd3ebe2ed957c2bca9d3328.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 3 Jun 2021 13:38:59 +0000 (09:38 -0400)]
powerpc: Don't use relative include for config.h in global_data.h
As there is an arch/powerpc/include/asm/config.h file using "" to get
config.h here can lead to using that rather than include/config.h. This
in turn can lead to a mismatch in the size of gd.
Cc: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Heinrich Schuchardt [Sat, 29 May 2021 11:18:00 +0000 (13:18 +0200)]
malloc: add SPDX license identifiers
The original code is in the public domain. Licenses/README states that the
general license for U-Boot is GPL 2.0+. So we can mark the malloc code as
GPL 2.0+ too.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Bin Meng [Tue, 22 Jun 2021 13:16:23 +0000 (21:16 +0800)]
MAINTAINERS: Add an entry for NVMe
This was missed when NVMe support was initially brought to U-Boot
back in 2017. Add an entry for it and list myself as the maintainer.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Tue, 22 Jun 2021 13:16:22 +0000 (21:16 +0800)]
doc: develop: Convert README.nvme to reST
This converts the existing README.nvme to reST, and puts it under
the develop/driver-model/ directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 22 Jun 2021 13:16:21 +0000 (21:16 +0800)]
nvme: Don't clear nvme blk device's priv space
A udevice's priv space is cleared in alloc_priv() in the DM core.
Don't do it again in its probe() routine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 22 Jun 2021 13:16:20 +0000 (21:16 +0800)]
nvme: Drop useless members of 'struct nvme_ns'
mode_select_num_blocks and mode_select_block_len in 'struct nvme_ns'
are not useful. Drop them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 22 Jun 2021 13:16:19 +0000 (21:16 +0800)]
nvme: Eliminate the offset of one during block dev creation
At present there is an offset of one added during the creation of
block device. This can be very confusing as we wanted to encode the
namespace id in the block device name but namespae id cannot be zero.
This changes to use the namespace id directly in the block device
name, eliminating the offset of one effectively.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 22 Jun 2021 13:16:18 +0000 (21:16 +0800)]
nvme: Skip block device creation for inactive namespaces
At present for each namespace there is a block device created for it.
There is no issue if the number of supported namespaces reported from
the NVMe device is only 1.
Since QEMU commit
7f0f1acedf15 ("hw/block/nvme: support multiple namespaces"),
the number of supported namespaces reported has been changed from 1
to 256, but not all of them are active namespaces. The actual active
one depends on the QEMU command line parameters. A common case is
that namespace 1 being active and all other 255 being inactive.
If a namespace is inactive, the namespace identify command returns a
zero filled data structure. We can use field NSZE (namespace size) to
decide whether a block device should be created for it.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Tue, 22 Jun 2021 13:16:17 +0000 (21:16 +0800)]
nvme: Move block dev creation from uclass post_probe() to driver probe()
At present the block device creation happens in the NVMe uclass
driver post_probe() phase. In preparation to support multiple
namespaces, we should issue namespace identify before creating
block devices but that touches the underlying hardware hence it
is not appropriate to do such in the uclass driver post_probe().
Let's move it to driver probe() phase instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Wesley Sheng [Tue, 22 Jun 2021 03:34:43 +0000 (11:34 +0800)]
nvme: Remove the redundant aqa value setting
AQA (Admin Queue Attributes) register is a dword size with
lower word of ASQS, and higher word of ACQS.
The code set the variable aqa twice, but it is redundant.
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Wesley Sheng [Tue, 22 Jun 2021 03:34:21 +0000 (11:34 +0800)]
nvme: Correct the prps per page calculation method
Each prp is 8 bytes, calculate the number of prps
per page should just divide page size by 8
there is no need to minus 1
Signed-off-by: Wesley Sheng <wesleyshenggit@sina.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
David Lamparter [Thu, 6 May 2021 18:24:30 +0000 (20:24 +0200)]
nvme: fix for big endian systems
writel() and co. already include the endian swap; doing the swap twice
is, er, unhelpful.
Tested on a P4080DS, which boots perfectly fine off NVMe with this.
Signed-off-by: David Lamparter <equinox@diac24.net>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Bin Meng [Fri, 18 Jun 2021 07:09:30 +0000 (15:09 +0800)]
x86: Discard .note.gnu.property sections
When switching to kernel.org x86_64 gcc 11.1.0 toolchain, u-boot.rom
built from qemu-x86_defconfig no longer boots anymore. Investigation
shows that U-Boot fails at a very early stage during the boot process,
in fdtdec_prepare_fdt() where fdt_check_header() complains that there
is not a valid device tree found at gd->fdt_blob which points to _end.
Now _end points to an allocated section .note.gnu.property which of
course is wrong.
This issue is however not seen when using the default Ubuntu 20.04 gnu
toolchain (gcc 9.3.0 with binutils 2.34). Further investigation shows
that it is caused by a behavior change of binutils v2.36 which is part
of the kernel.org gcc 11.1.0 toolchain, via the following commit:
939b95c77bf2 ("Linux/x86: Configure gas with --enable-x86-used-note by default")
In fact, there was already a regression bug report [1] for binutils two
months ago, but the binutils folks did not think it is a bug :(
To resolve this, there are several options:
* pass -Wa,-mx86-used-note=no to gas
* pass -R .note.gnu.property to objcopy
* discard the section in the linker script
Linux kernel uses the discard way [2], so let's do the same for U-Boot.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=27753
[2] commit
4caffe6a28d3 ("x86/vdso: Discard .note.gnu.property sections in vDSO")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Jan Kiszka [Sun, 20 Jun 2021 20:29:13 +0000 (22:29 +0200)]
Makefile: Adjust indention of GENENV quiet output
The column width for a command name is 8.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Da Xue [Tue, 22 Jun 2021 02:39:19 +0000 (22:39 -0400)]
autoboot: fix typos of CONFIG_AUTOBOOT_USE_MENUKEY
Replace typo CONFIG_USE_AUTOBOOT_MENUKEY with
CONFIG_AUTOBOOT_USE_MENUKEY as when they were introduced initially there
was some mismatch in which name was used where.
Fixes:
8fc31e23aa83 ("autoboot: Rename CONFIG_MENUKEY to CONFIG_AUTOBOOT_MENUKEY")
Signed-off-by: Da Xue <da@libre.computer>
Christian Melki [Mon, 7 Jun 2021 09:21:15 +0000 (11:21 +0200)]
disk/part_dos.c: Fix a variable typo in write_mbr_partitions()
This function is passed *dev not *dev_desc, so pass the right name to
part_init().
Fixes:
f14c5ee5ab8b ("disk: part_dos: update partition table entries after write")
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Bin Meng [Mon, 21 Jun 2021 23:33:21 +0000 (07:33 +0800)]
azure: Use msys2
20210604 installer for Windows build
MSYS2 Windows build started to fail since yesterday (Jun 21):
checking keyring...
checking package integrity...
error: gcc-libs: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-libs-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: gcc: signature from "David Macek <david.macek.0@gmail.com>" is unknown trust
:: File /var/cache/pacman/pkg/gcc-10.2.0-1-x86_64.pkg.tar.zst is corrupted (invalid or corrupted package (PGP signature)).
error: failed to commit transaction (invalid or corrupted package)
Errors occurred, no packages were upgraded.
Switching to the latest installer (version
20210604) seems to fix it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com>
Fabio Estevam [Mon, 7 Jun 2021 20:40:09 +0000 (17:40 -0300)]
Revert "mmc: fsl_esdhc_imx: use VENDORSPEC_FRC_SDCLK_ON to control card clock output"
This reverts commit
63756575b42b8b4fb3f59cbbf0cedf03331bc2d2.
Since this commit a imx6qdl-pico board boots extremely slowly
in both SPL as well as U-Boot proper.
Fix this regression by reverting the offending commit for now.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Pierre-Jean Texier <texier.pj2@gmail.com>
Jaehoon Chung [Sun, 30 May 2021 23:31:50 +0000 (08:31 +0900)]
mmc: mmc-uclass: change to static about dm function
Change to static about dm function.
They can be used with wrapper functions.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Sun, 30 May 2021 23:31:49 +0000 (08:31 +0900)]
mmc: fsl_esdhc_imx: use mmc_send_cmd instead of dm_mmc_send_cmd
Use mmc_send_cmd instead of dm_mmc_send_cmd.
It doesn't need to distinguish this function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reuben Dowle [Thu, 13 May 2021 22:15:43 +0000 (10:15 +1200)]
mmc: Update environment variable with active partition
This patch allows uboot scripts make choices about where to boot from based
on the active mmc boot partition. This allows having two copies of kernel,
filesystems etc, and choosing which to boot from based off of the active
bootloader partition.
Signed-off-by: Reuben Dowle <reuben.dowle@4rf.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Ley Foon Tan [Mon, 26 Apr 2021 05:17:46 +0000 (13:17 +0800)]
mmc: dwmmc: socfpga: Get "fifo-mode" property from DT
Add FIFO mode support for SoCFPGA dwmmc, read "fifo-mode" property from DT.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Ley Foon Tan [Mon, 26 Apr 2021 03:35:05 +0000 (11:35 +0800)]
mmc: dw_mmc: Fixes data read when receiving DTO interrupt in FIFO mode
The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Weijie Gao [Tue, 20 Apr 2021 08:37:10 +0000 (16:37 +0800)]
mmc: mtk-sd: increase the minimum bus frequency
With a 48MHz input clock, the lowest bus frequency can be as low as
48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
the mmc framework take seconds to finish the initialization.
Limiting the minimum bus frequency to a slightly higher value can solve the
issue without any side effects.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Andrey Zhizhikin [Sat, 1 May 2021 20:23:04 +0000 (22:23 +0200)]
imx8mm: configs: enable distro default features
imx8mm ekv has been switched to use distro boot commands, but had no
correct options enabled to support sysboot.
According to the README.distro, sysboot is consindered to be a
recommended way of using distro boot commands, it required default distro
features to be enabled instead of only those that are relevant to the boot
script.
Replace the boot script specific options in the config to a default distro
option.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Fixes:
2df8930bf9 ("imx8mm: configs: add support for distro boot commands")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Andrey Zhizhikin [Sat, 1 May 2021 20:23:05 +0000 (22:23 +0200)]
imx8mp: configs: enable distro default features
imx8mp ekv has been switched to use distro boot commands, but had no
correct options enabled to support sysboot.
According to the README.distro, sysboot is consindered to be a
recommended way of using distro boot commands, it required default distro
features to be enabled instead of only those that are relevant to the boot
script.
Replace the boot script specific options in the config to a default distro
option.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Fixes:
9b162b1d1f ("imx8mp: configs: add support for distro boot commands")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fabio Estevam [Thu, 17 Jun 2021 15:57:29 +0000 (12:57 -0300)]
o4-imx-nano: Fix dtc warnings
Remove the LED unit addresses and reg properties to
fix the following dtc build warnings:
arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
...
arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
Tom Rini [Fri, 18 Jun 2021 15:18:56 +0000 (11:18 -0400)]
Merge branch 'network_master' of https://source.denx.de/u-boot/custodians/u-boot-net
Tim Harvey [Thu, 17 Jun 2021 23:08:54 +0000 (16:08 -0700)]
net: octeontx: smi: use dt live tree API
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Dimitri John Ledkov [Wed, 21 Apr 2021 11:42:01 +0000 (12:42 +0100)]
cmd: pxe_utils: sysboot: fix crash if either board or soc are not set.
If the environment does not have "soc" or "board" set, and fdtdir
option is specified in extlinux.conf, the bootloader will crash whilst
dereferencing a null pointer. Add a guard against null soc or
board. Fixes a crash of qemu-riscv64_smode configuration, which does
not have CONFIG_SYS_SOC defined.
Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Michael Walle [Thu, 25 Feb 2021 15:51:11 +0000 (16:51 +0100)]
net: use the same alias stem for ethernet as linux
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:
$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633
In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit
fc054d563bfb ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.
Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.
Cc: David Wu <david.wu@rock-chips.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Michael Walle [Wed, 24 Feb 2021 16:30:44 +0000 (17:30 +0100)]
net: use a more deterministic approach to get the active ethernet device
If the environment variable "ethact" is not set, the first device in the
uclass is returned. This depends on the probing order of the ethernet
devices. Moreover it is not not configurable at all.
Try to return the ethernet device with sequence id 0 first which then
can be configured by the aliases in a device tree. Fall back to the old
mechanism in case of an error.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Heinrich Schuchardt [Thu, 3 Jun 2021 07:52:41 +0000 (07:52 +0000)]
net: sun8i-emac: fix MDIO frequency
Commit
4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency") leads to
network failure on the OrangePi PC.
=> dhcp
sun8i_emac_eth_start: Timeout
According to the commit message the change of the MDIO frequency is only
required for external PHYs.
Fixes:
4f0278dac56a ("net: sun8i-emac: Lower MDIO frequency")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Jassi Brar [Fri, 4 Jun 2021 09:44:38 +0000 (18:44 +0900)]
net: synquacer: Add netsec driver
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Daniil Stas [Sun, 30 May 2021 13:34:09 +0000 (13:34 +0000)]
net: dwc_eth_qos: Revert some changes of commit
3a97da12ee7b
Revert some changes of commit
3a97da12ee7b ("net: dwc_eth_qos: add dwc
eqos for imx support") that were probably added by mistake.
One of these changes can lead to received data corruption (enabling
FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings
for some platforms. And another makes some writes at unknown memory
location.
Fixes:
3a97da12ee7b ("net: dwc_eth_qos: add dwc eqos for imx support")
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ye Li <ye.li@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Daniil Stas [Sun, 23 May 2021 22:24:48 +0000 (22:24 +0000)]
net: dwc_eth_qos: Fix needless phy auto-negotiation restarts
Disabling clk_ck clock leads to link up status loss in phy, which
leads to auto-negotiation restart before each network command
execution.
This issue is especially big for PXE boot protocol because of
auto-negotiation restarts before each configuration filename trial.
To avoid this issue don't disable clk_ck clock after it was enabled.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tim Harvey [Fri, 16 Apr 2021 20:25:09 +0000 (13:25 -0700)]
net: e1000: do not attempt to set hwaddr for i210 without FLASH
commit
f1bcad22dd19 ("net: e1000: add support for writing to EEPROM")
adds support for storing hwaddr in EEPROM however i210 devices do not
support this and thus results in errors such as:
Warning: e1000#0 failed to set MAC address'
Check if a flash device is present and if not return -ENOSYS indicating
this is not supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Hou Zhiqiang [Sat, 12 Jun 2021 18:15:41 +0000 (21:15 +0300)]
Fix a memory leak issue in the RX port initialization.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tom Rini [Thu, 17 Jun 2021 12:44:56 +0000 (08:44 -0400)]
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq
- fsl-qoriq: Bug fixes related pfe, eth, thermal node, vid.c, cpu release,
mmc, usb, env, etc for Layerscape boards
- powerpc: Update Maintainers for some boards.
Tom Rini [Thu, 17 Jun 2021 12:44:23 +0000 (08:44 -0400)]
Merge branch 'master' of https://source.denx.de/u-boot/custodians/u-boot-riscv
- ae350 related dts fixes.
Priyanka Jain [Thu, 17 Jun 2021 07:22:46 +0000 (12:52 +0530)]
board: freescale: t1028xrdb: Add MAINTAINER for revD
Add Priyanka Jain as MAINTAINER for
T2080RDB_revD_defconfig,
T2080RDB_revD_NAND_defconfig,
T2080RDB_revD_SDCARD_defconfig and
T2080RDB_revD_SPIFLASH_defconfig
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Ran Wang [Wed, 16 Jun 2021 12:23:19 +0000 (17:53 +0530)]
armv8: Update erratum number to align with doc
Change the USB erratum number A-050106 to A-050204 as A-050106 is
a duplicate and never be published.
Fixes
0cfa00cdb94 (“armv8: Add workaround for USB erratum A-050106”)
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Fri, 11 Jun 2021 12:28:08 +0000 (15:28 +0300)]
board: freescale: t208xrdb: add a config option for rev D dts fixups
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Wed, 16 Jun 2021 12:17:31 +0000 (17:47 +0530)]
board: freescale: t208xrdb: add Linux fdt fix-ups for rev D
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Fri, 11 Jun 2021 12:28:06 +0000 (15:28 +0300)]
board: freescale: t208xrdb: detect the board revision version
Detect and print the board revision version based on the CPLD registers.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Camelia Groza [Fri, 11 Jun 2021 12:28:05 +0000 (15:28 +0300)]
board: freescale: t208xrdb: remove the legacy non-DM_ETH code
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the
board_eth_init() callback and the non-DM_ETH code paths since they are not
needed anymore.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:25:21 +0000 (14:25 +0000)]
pg-wcom-ls102xa: fix sys counter frequency
A system clock of 66MHz was chosen for the pg-wcom-ls102xa.
Compared to the Evalboard, this corresponds to a reduction of 1/3.
The system counter clock should have been reduced accordingly,
but that was not the case, so we had a system time that was
1/3 behind the real time.
This patch corrects the system counter clock to
8.333MHz = 66.667MHz / 8.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:24:32 +0000 (14:24 +0000)]
pg-wcom-ls102x: initialize front led and app buf
This patch adds the front led initialization and the application
buffer enable to the eraly board inititlaization.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:23:34 +0000 (14:23 +0000)]
km: ls102x: update device disable configuration acc hw design desc
In order to improve power consumption ls102x allows to disable peripherals
that are not in use.
This patch follows SELI8 HW design description and disables peripherals
that are not in use in our designs, the same configuration is applicable
and for EXPU1.
This patch uses available hwconfig option for updating ls102x device
disable configuration.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:21:15 +0000 (14:21 +0000)]
km: ls102x: set ethrotate envvar to no
The default behavior in the latest u-boot revisions is to rotate the
active net device to the next available if the requested link is not
established.
For our ls102x based devices this would mean that if active debug net
device is not available, u-boot will rotate and set the next net device
that is one of the estar adapters.
To return from this situation manual action to set correct ethact
adapter will be needed and this can be annoying when working in
debug mode.
Setting ethrotate=no will disable net adapter rotation and will make sure
that the primary adapter is always used.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:20:13 +0000 (14:20 +0000)]
km/scripts: fix saveenv command syntax
This is most probably a typo, and in older u-uboot versions is same as
'saveenv', in the newer uboot versions there is a separate 'save' command
that is different from 'saveenv'.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:19:08 +0000 (14:19 +0000)]
km: ls102xa: add missing define for PRAM regions
In our designs we reserve PRAM area at the end of the RAM, and in order
this area to be visible and taken into account by the u-boot memory mgmt
CONFIG_PRAM has to be defined.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:17:34 +0000 (14:17 +0000)]
km/ls102xa: add support for u-boot POST memory test
From production view this is standard test executed during production on
all linux based foxmc cards.
On CENT2 HW defined memory region is zero means that some DDR accesses are
done by memory_post_dataline and memory_post_addrline but pattern tests
are skipped that's why mem_regions is fast there.
On ls102x for the complete DDR region of 1GiB memory_regions_post_test
takes approx. 4min and this is too much for production, so this patch
defines only 1MiB region as compromise.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Tue, 8 Jun 2021 14:16:28 +0000 (14:16 +0000)]
board/km: add support for expu1 design based on nxp
The EXPU1 design is a new 40G capable ethernet service unit card for
Hitachi-Powergrids wired-com product lines.
The base SoC is same as for already added SELI8 card, consequently the
already added u-boot support for SELI8 is reused.
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
[Fixed new line error at EOF]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:07:01 +0000 (13:37 +0530)]
board: freescale: t102xrdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t102xrdb board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:07:00 +0000 (13:37 +0530)]
board: freescale: p2041rdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p2041rdb board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:06:59 +0000 (13:36 +0530)]
board: freescale: p1_p2_rdb_pc: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for p1_p2_rdb_pc board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Tue, 8 Jun 2021 08:06:58 +0000 (13:36 +0530)]
board: freescale: t4rdb: Add MAINTAINER
Add "Priyanka Jain <priyanka.jain@nxp.com>" as
MAINTAINER for t4rdb board.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Lasse Klok Mikkelsen [Tue, 8 Jun 2021 06:39:12 +0000 (08:39 +0200)]
arm: dts: ls1021a.dtsi: Fix invalid reg on gpio nodes
Address and size cells on SOC are set to 1. But gpio nodes are specified
with 2 cells. This fixes the gpio nodes to correct cells.
Signed-off-by: Lasse Klok Mikkelsen <lkmi@prevas.dk>
Reviewed-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Fri, 4 Jun 2021 13:40:58 +0000 (13:40 +0000)]
net: tsec: add option to set device max-speed via dts
Current tsec adapter sets adapter gigabit capabilities by default, and in
reality this must not always be the case.
It is possible that tsec adapter is used for 100Mbps connection, and in
this case setting 1000Mbps capabilities can lead to some side effects such
longer autoneg process.
In our ls102x designs this problem leads to long autoneg times (> 4 sec)
in case board rgmii link is 100Mbps capable only.
Limiting the rgmii link capabilities provides faster and smoother
link establishment.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Fri, 4 Jun 2021 09:25:00 +0000 (09:25 +0000)]
keymile: common: fix hexadecimal env variable format
Commit df86d32 breaks linux kernel and product application boot.
Linux kernel and our product application scripts are expecting 0x prefix
for hexadecimal values, while env_set_hex writes them without a prefix.
This patch partially revert env_set_hex usage for affected env variables.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Aleksandar Gerasimovski [Fri, 4 Jun 2021 09:17:56 +0000 (09:17 +0000)]
configs: seli8: set envsize to 0x4000
During the mainlining of the board this was by mistake set to sector size.
Our user space env scripts are expecting envsize of 0x4000, and setting
this differently will break our cross-platform compatibility.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:19 +0000 (10:51 +0800)]
armv8: layerscape: drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
Drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33. CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
is used instead.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Michael Walle <michael@walle.cc> [for kontron-sl28]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:18 +0000 (10:51 +0800)]
mmc: fsl_esdhc_imx: drop CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
There is no i.MX board using such option. Drop it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Thu, 3 Jun 2021 02:51:17 +0000 (10:51 +0800)]
mmc: fsl_esdhc: convert to CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT
For eSDHC, power supply is through peripheral circuit.
Some eSDHC versions have value 0 of the bit but that
does not reflect the truth. 3.3V is common for SD/MMC,
and is supported for all boards with eSDHC in current
u-boot. So, make 3.3V is supported in default in code.
CONFIG_FSL_ESDHC_VS33_NOT_SUPPORT can be enabled if
future board does not support 3.3V.
This is also a fix-up for one previous patch, which converted
to use IS_ENABLED() for CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
that is not a Kconfig option.
Fixes:
52faec31827e ("mmc: fsl_esdhc: replace most #ifdefs by IS_ENABLED()")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Matt Merhar [Sun, 30 May 2021 00:16:17 +0000 (00:16 +0000)]
board: freescale: p2041rdb: use correct EEPROM address length
These boards, according to the schematic and per the board I own, use an
M24256-BWDW6TP I2C EEPROM which requires two address bytes.
This fixes the 'mac' command which is used to program, among other
things, the MAC addresses for the ethernet interfaces on the board.
Signed-off-by: Matt Merhar <mattmerhar@protonmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Biwen Li [Fri, 21 May 2021 07:15:06 +0000 (15:15 +0800)]
configs: ls2088aqds: fix synchronous exception
IFC NOR flash base address of ls2088a is 0x580000000,
and offset of env crc is 0x500000, so fix the macro
CONFIG_ENV_ADDR to fix synchronous exception(access illegal address)
Fixes:
59071804c1 ("configs: ls2080a: Correct ENV_ADDR value")
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Kuldeep Singh [Wed, 19 May 2021 11:10:12 +0000 (16:40 +0530)]
configs: ls1088a: Enable CONFIG_SYS_RELOC_ENV_ADDR
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Fri, 14 May 2021 02:33:57 +0000 (10:33 +0800)]
arm: dts: lx2162aqds: support eMMC HS400 mode on esdhc1
Add properties related to eMMC HS400 mode for esdhc1.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 13 May 2021 06:54:32 +0000 (14:54 +0800)]
pci: layerscape-ep: Add check of the PCIe controller enablement
Stop to initialize the PCIe controller if it's disabled by RCW.
Fixes:
118e58e26eba ("pci: layerscape: Split the EP and RC driver")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chaitanya Sakinam [Fri, 7 May 2021 04:22:05 +0000 (12:22 +0800)]
armv8: ls1012a: Pass PPFE firmware to Linux through FDT
Read Linux PPFE firmware from flash partition and pass it to Linux through
FDT entry. So that we can avoid placing PPFE firmware in Linux rootfs.
(FDT may increase at max by 64KB)
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Signed-off-by: Anji J <anji.jagarlmudi@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Yangbo Lu [Tue, 27 Apr 2021 08:42:11 +0000 (16:42 +0800)]
armv8: layerscape: enable eMMC HS400 workarounds for LX2160A/LX2162A
Enable eMMC HS400 workarounds for LX2160A/LX2162A.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Jiafei Pan [Wed, 21 Apr 2021 04:12:49 +0000 (12:12 +0800)]
armv8: layerscape: add PSCI support for cpu release
For cpu release command, check whether PSCI is supported firstly,
if supported, use PSCI to kick off secondary cores, otherwise still
use spin table.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
[Fixed checkpatch alignment CHECKs]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Singh [Mon, 19 Apr 2021 05:45:04 +0000 (11:15 +0530)]
board: freescale: vid.c: Add check for return value of adjust_vdd()
Add check for return value of adjust_vdd()
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Bin Meng [Tue, 15 Jun 2021 05:45:57 +0000 (13:45 +0800)]
riscv: andes_plic: Fix riscv_get_ipi() mask
Current logic in riscv_get_ipi() for Andes PLICSW does not look
correct. The mask to test IPI pending bits for a hart should be
left shifted by (8 * gd->arch.boot_hart), just the same as what
is done in riscv_send_ipi().
Fixes:
8b3e97badf97 ("riscv: add functions for reading the IPI status")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 23:00:30 +0000 (07:00 +0800)]
riscv: ae350: doc: Remove CONFIG_SKIP_LOWLEVEL_INIT
The doc says CONFIG_SKIP_LOWLEVEL_INIT is in ax25-ae350.h, while
actually it is not. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:13 +0000 (13:51 +0800)]
riscv: ae350: dts: Add missing "u-boot, dm-spl" for SPL config
At present the AE350 SPL defconfig is using OF_PRIOR_STAGE. The
intention was to use gdb to load device tree before running U-Boot
SPL/proper from RAM. When we switch to OF_SEPARATE we will have to
use our own DT but without "u-boot,dm-spl" in several essential
nodes, SPL does not boot.
Let's add all the required "u-boot,dm-spl" for SPL config.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:12 +0000 (13:51 +0800)]
riscv: ae350: dts: Fix #interrupt-cells for plic0 in 32-bit
All the device nodes that refer to plic0 as their interrupt parent
have 2 cells encoded in their interrupts property, but plic0 only
provides 1 cell in #interrupt-cells which is incorrect.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:11 +0000 (13:51 +0800)]
riscv: ae350: dts: Remove the unnecessary #address-cells in plic nodes
PLIC nodes don't have child nodes, so #address-cells is not needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:10 +0000 (13:51 +0800)]
riscv: ae350: dts: Remove the unnecessary space in bootargs
There are two spaces before "debug' in bootargs. Drop one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Bin Meng [Fri, 4 Jun 2021 05:51:09 +0000 (13:51 +0800)]
riscv: ae350: dts: Add SPDX license header
The SPDX license header is currently missing. Add one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tom Rini [Wed, 16 Jun 2021 15:18:11 +0000 (11:18 -0400)]
Merge tag 'u-boot-imx-
20210616' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-
20210616
-------------------
- imxrt : fixes, USB, imxrt1020-evk
- imx8m:
fix for verdin-imx8mm
Add conga-QMX8 board
- imx6 :
documentation for pico-imx6:
Add SeeedStudio NPI-IMX6ULL Support
ventana: DM PCI
- imx7d:
added SMEGW01 board
CI : https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/7765
Mian Yousaf Kaukab [Wed, 14 Apr 2021 10:33:58 +0000 (12:33 +0200)]
ls1012a: net: pfe: remove pfe stop from bootcmd
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Michael Walle [Tue, 13 Apr 2021 15:54:17 +0000 (17:54 +0200)]
board: sl28: fix RGMII clock and voltage
It was noticed that the clock isn't continuously enabled when there is
no link. This is because the 125MHz clock is derived from the internal
PLL which seems to go into some kind of power-down mode every once in a
while. The LS1028A expects a contiuous clock. Thus enable the PLL all
the time.
Also, the RGMII pad voltage is wrong, it was configured to 2.5V (that is
the VDDH regulator). The correct voltage is 1.8V, i.e. the VDDIO
regulator.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Manish Tomar [Tue, 13 Apr 2021 07:08:34 +0000 (12:38 +0530)]
configs: ls1046afrwy: Add secure boot config
Add required CONFIG_NXP_ESBC for ls1046afrwy to enable ESBC Chain of Trust.
Signed-off-by: Manish Tomar <manish.tomar@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>