Kiran Gunda [Fri, 4 Oct 2019 10:16:55 +0000 (15:46 +0530)]
regulator: qcom-rpmh: Fix PMIC5 BoB min voltage
Correct the PMIC5 BoB min voltage from 0.3V to 3V. Also correct
the voltage selector accordingly.
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Link: https://lore.kernel.org/r/1570184215-5355-1-git-send-email-kgunda@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Yizhuo [Sun, 29 Sep 2019 17:09:57 +0000 (10:09 -0700)]
regulator: pfuze100-regulator: Variable "val" in pfuze100_regulator_probe() could be uninitialized
In function pfuze100_regulator_probe(), variable "val" could be
initialized if regmap_read() fails. However, "val" is used to
decide the control flow later in the if statement, which is
potentially unsafe.
Signed-off-by: Yizhuo <yzhai003@ucr.edu>
Link: https://lore.kernel.org/r/20190929170957.14775-1-yzhai003@ucr.edu
Signed-off-by: Mark Brown <broonie@kernel.org>
Charles Keepax [Tue, 1 Oct 2019 13:20:17 +0000 (14:20 +0100)]
regulator: lochnagar: Add on_off_delay for VDDCORE
The VDDCORE regulator takes a good length of time to discharge down, so
add an on_off_delay to ensure DCVDD is removed before it is powered on
again.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191001132017.1785-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Sun, 29 Sep 2019 09:58:48 +0000 (17:58 +0800)]
regulator: ti-abb: Fix timeout in ti_abb_wait_txdone/ti_abb_clear_all_txdone
ti_abb_wait_txdone() may return -ETIMEDOUT when ti_abb_check_txdone()
returns true in the latest iteration of the while loop because the timeout
value is abb->settling_time + 1. Similarly, ti_abb_clear_all_txdone() may
return -ETIMEDOUT when ti_abb_check_txdone() returns false in the latest
iteration of the while loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20190929095848.21960-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Marco Felsch [Tue, 17 Sep 2019 12:42:42 +0000 (14:42 +0200)]
regulator: da9062: fix suspend_enable/disable preparation
Currently the suspend reg_field maps to the pmic voltage selection bits
and is used during suspend_enabe/disable() and during get_mode(). This
seems to be wrong for both use cases.
Use case one (suspend_enabe/disable):
Those callbacks are used to mark a regulator device as enabled/disabled
during suspend. Marking the regulator enabled during suspend is done by
the LDOx_CONF/BUCKx_CONF bit within the LDOx_CONT/BUCKx_CONT registers.
Setting this bit tells the DA9062 PMIC state machine to keep the
regulator on in POWERDOWN mode and switch to suspend voltage.
Use case two (get_mode):
The get_mode callback is used to retrieve the active mode state. Since
the regulator-setting-A is used for the active state and
regulator-setting-B for the suspend state there is no need to check
which regulator setting is active.
Fixes:
4068e5182ada ("regulator: da9062: DA9062 regulator driver")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20190917124246.11732-2-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Philippe Schenker [Mon, 23 Sep 2019 08:18:49 +0000 (08:18 +0000)]
dt-bindings: fixed-regulator: fix compatible enum
Remove 'const:' in the compatible enum. This was breaking
make dt_binding_check since it has more than one compatible string.
Fixes:
9c86d003d620 ("dt-bindings: regulator: add regulator-fixed-clock binding")
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190923081840.23391-1-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Sun, 22 Sep 2019 02:29:28 +0000 (10:29 +0800)]
regulator: fixed: Prevent NULL pointer dereference when !CONFIG_OF
Use of_device_get_match_data which has NULL test for match before
dereference match->data. Add NULL test for drvtype so it still works
for fixed_voltage_ops when !CONFIG_OF.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190922022928.28355-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Marco Felsch [Tue, 17 Sep 2019 15:40:21 +0000 (17:40 +0200)]
regulator: core: make regulator_register() EPROBE_DEFER aware
Sometimes it can happen that the regulator_of_get_init_data() can't
retrieve the config due to a not probed device the regulator depends on.
Fix that by checking the return value of of_parse_cb() and return
EPROBE_DEFER in such cases.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-4-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marco Felsch [Tue, 17 Sep 2019 15:40:20 +0000 (17:40 +0200)]
regulator: of: fix suspend-min/max-voltage parsing
Currently the regulator-suspend-min/max-microvolt must be within the
root regulator node but the dt-bindings specifies it as subnode
properties for the regulator-state-[mem/disk/standby] node. The only DT
using this bindings currently is the at91-sama5d2_xplained.dts and this
DT uses it correctly. I don't know if it isn't tested but it can't work
without this fix.
Fixes:
f7efad10b5c4 ("regulator: add PM suspend and resume hooks")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20190917154021.14693-3-m.felsch@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
H. Nikolaus Schaller [Tue, 10 Sep 2019 19:22:29 +0000 (21:22 +0200)]
regulator: core: Fix error return for /sys access
regulator_uV_show() is missing error handling if regulator_get_voltage_rdev()
returns negative values. Instead it prints the errno as a string, e.g. -EINVAL
as "-22" which could be interpreted as -22 µV.
We also do not need to hold the lock while converting the integer to a string.
Reported-by: Adam Ford <aford173@gmail.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Adam Ford <aford173@gmail.com>
Link: https://lore.kernel.org/r/f37f2a1276efcb34cf3b7f1a25481175be048806.1568143348.git.hns@goldelico.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Torokhov [Tue, 10 Sep 2019 17:02:46 +0000 (10:02 -0700)]
regulator: da9211: fix obtaining "enable" GPIO
This fixes
11da04af0d3b, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply "enable"
when moving to using devm_gpiod_get_from_of_node().
Fixes:
11da04af0d3b ("regulator: da9211: Pass descriptors instead of GPIO numbers")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170246.GA56792@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Torokhov [Tue, 10 Sep 2019 17:00:50 +0000 (10:00 -0700)]
regulator: max77686: fix obtaining "maxim,ena" GPIO
This fixes
96392c3d8ca4, as devm_gpiod_get_from_of_node() does
not do translation "con-id" -> "con-id-gpios" that our bindings expects,
and therefore it was wrong to change connection ID to be simply
"maxim,ena" when moving to using devm_gpiod_get_from_of_node().
Fixes:
96392c3d8ca4 ("regulator: max77686: Pass descriptor instead of GPIO number")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190910170050.GA55530@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
Kunihiko Hayashi [Tue, 10 Sep 2019 01:51:44 +0000 (10:51 +0900)]
regulator: uniphier: Add Pro5 USB3 VBUS support
Pro5 SoC has same scheme of USB3 VBUS as Pro4, so the data for Pro5 is
equivalent to Pro4.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1568080304-1572-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Philippe Schenker [Tue, 10 Sep 2019 06:21:19 +0000 (06:21 +0000)]
dt-bindings: regulator: add regulator-fixed-clock binding
This adds the documentation to the compatible regulator-fixed-clock.
This binding is a special binding of regulator-fixed and adds the
ability to add a clock to regulator-fixed, so the regulator can be
enabled and disabled with that clock. If the special compatible
regulator-fixed-clock is used it is mandatory to supply a clock.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20190910062103.39641-4-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Philippe Schenker [Tue, 10 Sep 2019 06:21:15 +0000 (06:21 +0000)]
regulator: fixed: add possibility to enable by clock
This commit adds the possibility to choose the compatible
"regulator-fixed-clock" in devicetree.
This is a special regulator-fixed that has to have a clock, from which
the regulator gets switched on and off.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20190910062103.39641-2-philippe.schenker@toradex.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Krzysztof Kozlowski [Mon, 9 Sep 2019 15:57:23 +0000 (17:57 +0200)]
regulator: s2mps11: Consistently use local variable
The value under 's2mps11->ext_control_gpiod[i]' is assigned to local
variable and used in probe in one place before. Use it consistently
later so code will be easier to read.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20190909155723.24734-1-krzk@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Sun, 8 Sep 2019 03:57:20 +0000 (11:57 +0800)]
regulator: lp87565: Simplify lp87565_buck_set_ramp_delay
Use rdev->regmap/&rdev->dev instead of lp87565->regmap/lp87565->dev.
In additional, the lp87565->dev actually is the parent mfd device,
so the dev_err message is misleading here with lp87565->dev.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190908035720.17748-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dmitry Torokhov [Wed, 4 Sep 2019 21:42:00 +0000 (14:42 -0700)]
regulator: slg51000: use devm_gpiod_get_optional() in probe
The CS GPIO line is clearly optional GPIO (and marked as such in the
binding document) and we should handle it accordingly. The current code
treats all errors as meaning that there is no GPIO defined, which is
wrong, as it does not handle deferrals raised by the underlying code
properly, nor does it recognize non-existing GPIO from any other
initialization error.
As far as I can see the only reason the driver, unlike all others,
is using OF-specific devm_gpiod_get_from_of_node() so that it can
assign a custom label to the selected GPIO line. Given that noone else
needs that, it should not be doing that either.
Let's switch to using more appropriate devm_gpiod_get_optional().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20190904214200.GA66118@dtor-ws
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Mon, 9 Sep 2019 09:56:10 +0000 (10:56 +0100)]
Merge branch 'regulator-5.3' into regulator-5.4
Colin Ian King [Fri, 6 Sep 2019 13:06:32 +0000 (14:06 +0100)]
regulator: lp8788-ldo: make array en_mask static const, makes object smaller
Don't populate the array en_mask on the stack but instead make it
static const. Makes the object code smaller by 87 bytes.
Before:
text data bss dec hex filename
12967 3408 0 16375 3ff7 drivers/regulator/lp8788-ldo.o
After:
text data bss dec hex filename
12816 3472 0 16288 3fa0 drivers/regulator/lp8788-ldo.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190906130632.6709-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Guido Günther [Wed, 4 Sep 2019 19:35:00 +0000 (12:35 -0700)]
regulator: tps65132: Stop parsing DT when gpio is not found
In case of a missing (optional) gpio don't fall through up to
"ti,active-discharge-time-us" due to
devm_fwnode_get_index_gpiod_from_child() returning NULL (since
gpiod_get_from_of_node() returned NULL) but rather indicate success as
intended.
This makes the driver probe correctly when e.g. only the enable gpio is
given.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://lore.kernel.org/r/363bd50cc7c60daa57d614a341d1fd649f05194c.1567625660.git.agx@sigxcpu.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 4 Sep 2019 12:42:50 +0000 (13:42 +0100)]
regulator: Defer init completion for a while after late_initcall
The kernel has no way of knowing when we have finished instantiating
drivers, between deferred probe and systems that build key drivers as
modules we might be doing this long after userspace has booted. This has
always been a bit of an issue with regulator_init_complete since it can
power off hardware that's not had it's driver loaded which can result in
user visible effects, the main case is powering off displays. Practically
speaking it's not been an issue in real systems since most systems that
use the regulator API are embedded and build in key drivers anyway but
with Arm laptops coming on the market it's becoming more of an issue so
let's do something about it.
In the absence of any better idea just defer the powering off for 30s
after late_initcall(), this is obviously a hack but it should mask the
issue for now and it's no more arbitrary than late_initcall() itself.
Ideally we'd have some heuristics to detect if we're on an affected
system and tune or skip the delay appropriately, and there may be some
need for a command line option to be added.
Link: https://lore.kernel.org/r/20190904124250.25844-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested-by: Lee Jones <lee.jones@linaro.org>
Cc: stable@vger.kernel.org
Bartosz Golaszewski [Mon, 2 Sep 2019 15:13:32 +0000 (17:13 +0200)]
regulator: add missing 'static inline' to a helper's stub
The build fails when CONFIG_REGULATOR is not selected because the stub
for regulator_bulk_set_supply_names() is missing the 'static inline'
attribute.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190902151332.28058-1-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Bartosz Golaszewski [Fri, 30 Aug 2019 07:17:37 +0000 (09:17 +0200)]
regulator: provide regulator_bulk_set_supply_names()
There are many regulator consumers who - before using the regulator
bulk functions - set the supply names in regulator_bulk_data using
a for loop.
Let's provide a simple helper in the consumer API that allows users
to do the same with a single function call.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20190830071740.4267-2-brgl@bgdev.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Thu, 29 Aug 2019 12:54:35 +0000 (13:54 +0100)]
MAINTAINERS: Add keyword pattern on regulator_get_optional()
In an effort to try to contain abuses of regulator_get_optional() add a
keyword entry to the MAINTAINERS stanza for the regulator API so that the
regulator maintainers get CCed on new usages.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20190829125435.48770-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Thu, 29 Aug 2019 06:50:46 +0000 (06:50 +0000)]
regulator: sy8824x: add prefixes to BUCK_EN and MODE macros
Add prefixes to BUCK_EN and MODE macros to namespace them.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190829143927.395d0385@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Thu, 29 Aug 2019 06:49:18 +0000 (06:49 +0000)]
regulator: sy8824x: use c++style for the comment block near SPDX
Update the entire comment block to be C++ style so it looks consistent.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190829143749.4b42bc65@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Fri, 30 Aug 2019 11:29:22 +0000 (12:29 +0100)]
regulator: mt6358: Add BROKEN dependency while waiting for MFD to merge
The mt6358 driver was merged in error, it depends on an existing MFD
rather than a newly added one and needs updates to that driver. Disable
the build until those are merged.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hsin-Hsiung Wang [Fri, 23 Aug 2019 03:45:28 +0000 (11:45 +0800)]
regulator: mt6358: Add support for MT6358 regulator
The MT6358 is a regulator found on boards based on MediaTek MT8183 and
probably other SoCs. It is a so called pmic and connects as a slave to
SoC using SPI, wrapped inside the pmic-wrapper.
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1566531931-9772-8-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hsin-Hsiung Wang [Fri, 23 Aug 2019 03:45:26 +0000 (11:45 +0800)]
regulator: Add document for MT6358 regulator
add dt-binding document for MediaTek MT6358 PMIC
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Link: https://lore.kernel.org/r/1566531931-9772-6-git-send-email-hsin-hsiung.wang@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:49:45 +0000 (08:49 +0000)]
regulator: sy8824x: add SY20278 support
The differences between SY8824C and SY20278 are different regs
for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163830.2c94f29b@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:49:09 +0000 (08:49 +0000)]
dt-bindings: sy8824x: Document SY20278 support
SY20276 is an I2C-controlled adjustable voltage regulator made by
Silergy Corp. The differences between SY8824C and SY20278 are
different regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163754.170cf130@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:48:36 +0000 (08:48 +0000)]
regulator: sy8824x: add SY20276 support
The differences between SY8824C and SY20276 are different vsel_min,
vsel_step, vsel_count and regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163721.1947f7a0@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:48:04 +0000 (08:48 +0000)]
dt-bindings: sy8824x: Document SY20276 support
SY20276 is an I2C-controlled adjustable voltage regulator made by
Silergy Corp. The differences between SY8824C and SY20276 are
different vsel_min, vsel_step, vsel_count and regs for mode/enable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163650.47ed1213@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:47:30 +0000 (08:47 +0000)]
regulator: sy8824x: add SY8824E support
The only difference between SY8824E and SY8824C/D is the vsel_min.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163537.52023c4e@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:46:21 +0000 (08:46 +0000)]
dt-bindings: sy8824x: Document SY8824E support
SY8824E is an I2C-controlled adjustable voltage regulator made by
Silergy Corp. The only difference between SY8824C and SY8824E is the
vsel_min.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163505.361890af@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:45:33 +0000 (08:45 +0000)]
regulator: add support for SY8824C regulator
SY8824C is an I2C attached single output regulator made by Silergy Corp,
which is used on several Synaptics berlin platforms to control the
power supply of the ARM cores.
Add a driver for it.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163418.1a32fc48@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Jisheng Zhang [Tue, 27 Aug 2019 08:45:00 +0000 (08:45 +0000)]
regulator: add binding for the SY8824C voltage regulator
SY8824C is an I2C-controlled adjustable voltage regulator made by
Silergy Corp.
Add its device tree binding.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20190827163341.61df63a7@xhacker.debian
Signed-off-by: Mark Brown <broonie@kernel.org>
Raag Jadav [Tue, 13 Aug 2019 18:32:55 +0000 (00:02 +0530)]
regulator: act8865: operating mode and suspend state support
Implement ->set_mode(), ->get_mode() and ->set_suspend_xx() hooks
for act8865 with unlocked expert registers.
Based on work done by Borris Brezillon on [1].
[1] https://www.spinics.net/lists/kernel/msg2942960.html
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Link: https://lore.kernel.org/r/1565721176-8955-2-git-send-email-raagjadav@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Nishka Dasgupta [Thu, 15 Aug 2019 05:37:04 +0000 (11:07 +0530)]
regulator: core: Add label to collate of_node_put() statements
In function of_get_child_regulator(), the loop for_each_child_of_node()
contains two mid-loop return statements, each preceded by a statement
putting child. In order to reduce this repetition, create a new label,
err_node_put, that puts child and then returns the required value;
edit the mid-loop return blocks to instead go to this new label.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190815053704.32156-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Raag Jadav [Tue, 13 Aug 2019 18:32:56 +0000 (00:02 +0530)]
regulator: act8865 regulator modes and suspend states
Add documentation for act8865 regulator modes and suspend states.
Add active-semi,8865-regulator.h file for device tree binding constants
for act8865 regulators.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Link: https://lore.kernel.org/r/1565721176-8955-3-git-send-email-raagjadav@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Colin Ian King [Tue, 13 Aug 2019 13:31:14 +0000 (14:31 +0100)]
regulator: max8660: remove redundant assignment of variable ret
Variable ret is initialized to a value that is never read before
a return statement and hence can be removed. Remove it.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190813133114.14931-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andreas Kemnade [Wed, 14 Aug 2019 21:43:19 +0000 (23:43 +0200)]
regulator: twl: voltage lists for vdd1/2 on twl4030
_opp_supported_by_regulators() wrongly ignored errors from
regulator_is_supported_voltage(), so it considered errors as
success. Since
commit
498209445124 ("regulator: core: simplify return value on suported_voltage")
regulator_is_supported_voltage() returns a real boolean, so
errors make _opp_supported_by_regulators() return false.
That reveals a problem with the declaration of the VDD1/2
regulators on twl4030.
The VDD1/VDD2 regulators on twl4030 are neither defined with
voltage lists nor with the continuous flag set, so
regulator_is_supported_voltage() returns false and an error
before above mentioned commit (which was considered success)
The result is that after the above mentioned commit cpufreq
does not work properly e.g. dm3730.
[ 2.490997] core: _opp_supported_by_regulators: OPP minuV: 1012500 maxuV: 1012500, not supported by regulator
[ 2.501617] cpu cpu0: _opp_add: OPP not supported by regulators (
300000000)
[ 2.509246] core: _opp_supported_by_regulators: OPP minuV: 1200000 maxuV: 1200000, not supported by regulator
[ 2.519775] cpu cpu0: _opp_add: OPP not supported by regulators (
600000000)
[ 2.527313] core: _opp_supported_by_regulators: OPP minuV: 1325000 maxuV: 1325000, not supported by regulator
[ 2.537750] cpu cpu0: _opp_add: OPP not supported by regulators (
800000000)
The patch fixes declaration of VDD1/2 regulators by
adding proper voltage lists.
Fixes:
498209445124 ("regulator: core: simplify return value on suported_voltage")
Cc: stable@vger.kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Link: https://lore.kernel.org/r/20190814214319.24087-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
Raag Jadav [Mon, 12 Aug 2019 18:39:54 +0000 (00:09 +0530)]
regulator: act8945a-regulator: fix ldo register addresses in set_mode hook
According to ACT8945A datasheet[1], operating modes for ldos are
controlled by BIT(5) of their respective _CTRL registers.
[1] https://active-semi.com/wp-content/uploads/ACT8945A_Datasheet.pdf
Fixes:
7482d6ecc68e ("regulator: act8945a-regulator: Implement PM functionalities")
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Link: https://lore.kernel.org/r/1565635194-5816-1-git-send-email-raagjadav@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 25 Jul 2019 09:45:42 +0000 (11:45 +0200)]
regulator: twl6030: workaround the VMMC reset behavior
During reset the VMMC regulator doesn't reach 0V and only drops to
1.8V, furthermore the pulse width is under 200us whereas the SD
specification expect 1ms.
The WR_S bit allows the TWL6030 to no reset at all the VMMC during warm
reset and keep the current voltage. Thanks to this workaround the SD
card doesn't reach a undefined reset stage.
Actually this behavior is available for all the LDO regulator, so the
driver will also allow to use it with any of these regulator.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-4-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 25 Jul 2019 09:45:41 +0000 (11:45 +0200)]
regulator: twl6030: use variable for device node
Instead of refering the full pdev->dev.of_node use a local variable.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-3-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Gregory CLEMENT [Thu, 25 Jul 2019 09:45:40 +0000 (11:45 +0200)]
dt-bindings: regulator: twl6030: Add retain-on-reset property
During reset the VMMC regulator doesn't reach 0V and only drops to
1.8V, furthermore the pulse width is under 200us whereas the SD
specification expect 1ms.
For this 2 reasons being able to no reset at all the VMMC during warm
reset and keep the current voltage is a good workaround. The TWL6030
allows this but needs to be aware of it and this configuration should
also be shared with the bootloader.
This is the purpose of this new property: ti,retain-on-reset
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20190725094542.16547-2-gregory.clement@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Fri, 9 Aug 2019 07:36:16 +0000 (13:06 +0530)]
regulator: qcom-rpmh: Update PMIC modes for PMIC5
Add the PMIC5 modes and use them pmic5 ldo and smps
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-4-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Fri, 9 Aug 2019 07:36:15 +0000 (13:06 +0530)]
regulator: qcom-rpmh: Fix pmic5_bob voltage count
pmic5_bob voltages count is 136 [0,135] so update it
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-3-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Fri, 9 Aug 2019 07:36:14 +0000 (13:06 +0530)]
regulator: qcom-rpmh: Sort the compatibles
It helps to keep sorted order for compatibles, so sort them
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Fri, 9 Aug 2019 07:36:13 +0000 (13:06 +0530)]
regulator: dt-bindings: Sort the compatibles and nodes
It helps to keep sorted order for compatibles and nodes, so sort them
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190809073616.1235-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
YueHaibing [Wed, 7 Aug 2019 13:38:22 +0000 (21:38 +0800)]
regulator: act8865: Fix build error without CONFIG_POWER_SUPPLY
Building without CONFIG_POWER_SUPPLY will fail:
drivers/regulator/act8865-regulator.o: In function `act8865_pmic_probe':
act8865-regulator.c:(.text+0x357): undefined reference to `devm_power_supply_register'
drivers/regulator/act8865-regulator.o: In function `act8600_charger_get_property':
act8865-regulator.c:(.text+0x3f1): undefined reference to `power_supply_get_drvdata'
Add POWER_SUPPLY dependency to Kconfig.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes:
2d09a79bf637 ("regulator: act8865: Add support for act8600 charger")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190807133822.67124-1-yuehaibing@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Thu, 8 Aug 2019 09:33:43 +0000 (15:03 +0530)]
regulator: qcom-rpmh: Add support for SM8150
Add support from RPMH regulators found in SM8150 platform
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190808093343.5600-2-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Thu, 8 Aug 2019 09:33:42 +0000 (15:03 +0530)]
regulator: dt-bindings: Add PM8150x compatibles
Add PM8150, PM8150L and PM8009 compatibles for these PMICs found
in some Qualcomm platforms.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20190808093343.5600-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Dan Carpenter [Thu, 8 Aug 2019 10:33:35 +0000 (13:33 +0300)]
regulator: slg51000: Fix a couple NULL vs IS_ERR() checks
The devm_gpiod_get_from_of_node() function never returns NULL, it
returns error pointers on error.
Fixes:
a867bde3dd03 ("regulator: slg51000: add slg51000 regulator driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190808103335.GD30506@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
Nishka Dasgupta [Sun, 4 Aug 2019 16:20:23 +0000 (21:50 +0530)]
regulator: core: Add of_node_put() before return
Each iteration of for_each_child_of_node puts the previous node, but in
the case of a return from the middle of the loop, there is no put, thus
causing a memory leak. Hence add an of_node_put before the return in
two places.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190804162023.5673-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stephen Boyd [Tue, 30 Jul 2019 18:15:37 +0000 (11:15 -0700)]
regulator: Remove dev_err() usage after platform_get_irq()
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20190730181557.90391-38-swboyd@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Nishka Dasgupta [Wed, 24 Jul 2019 08:32:31 +0000 (14:02 +0530)]
regulator: of: Add of_node_put() before return in function
The local variable search in regulator_of_get_init_node takes the value
returned by either of_get_child_by_name or of_node_get, both of which
get a node. If this node is not put before returning, it could cause a
memory leak. Hence put search before a mid-loop return statement.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Link: https://lore.kernel.org/r/20190724083231.10276-1-nishkadg.linux@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild test robot [Wed, 24 Jul 2019 09:22:36 +0000 (17:22 +0800)]
regulator: act8865: fix ptr_ret.cocci warnings
drivers/regulator/act8865-regulator.c:447:8-14: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Fixes:
2d09a79bf637 ("regulator: act8865: Add support for act8600 charger")
CC: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20190724092236.witxtfmubun25l2t@1905cc33b6dd
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Thu, 11 Jul 2019 11:35:17 +0000 (19:35 +0800)]
regulator: lp87565: Fix probe failure for "ti,lp87565"
The "ti,lp87565" compatible string is still in of_lp87565_match_table,
but current code will return -EINVAL because lp87565->dev_type is unknown.
This was working in earlier kernel versions, so fix it.
Fixes:
7ee63bd74750 ("regulator: lp87565: Add 4-phase lp87561 regulator support")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190711113517.26077-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 24 Jul 2019 16:00:06 +0000 (17:00 +0100)]
Merge tag 'v5.3-rc1' into regulator-5.3
Linus 5.3-rc1
Michał Mirosław [Tue, 23 Jul 2019 16:32:07 +0000 (18:32 +0200)]
regulator: act8865: support regulator-pull-down property
AC8865 has internal 1.5k pull-down resistor that can be enabled when LDO
is shut down.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/d7338f0dfcac63eb958a6b5e42e2d540b3d3f54a.1563898936.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Michał Mirosław [Tue, 23 Jul 2019 16:32:06 +0000 (18:32 +0200)]
regulator: act8865: rename fixed LDO ops
Rename act8865_ldo_ops to act8865_fixed_ldo_ops to make room for
variable-output LDO ops change.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/12b1fe419e93dfe663990009bf1b2fbf630e9934.1563898936.git.mirq-linux@rere.qmqm.pl
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Tue, 23 Jul 2019 01:41:02 +0000 (09:41 +0800)]
regulator: stm32-booster: Remove .min_uV and .list_voltage for fixed regulator
Setting .n_voltages = 1 and .fixed_uV is enough for fixed regulator,
remove the redundant .min_uV and .list_voltage settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Link: https://lore.kernel.org/r/20190723014102.25103-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Maarten ter Huurne [Tue, 23 Jul 2019 01:14:18 +0000 (21:14 -0400)]
regulator: act8865: Add support for act8600 charger
This provides a way to monitor battery charge status via the power
supply subsystem.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20190723011418.29143-1-paul@crapouillou.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Thu, 11 Jul 2019 12:21:38 +0000 (20:21 +0800)]
regulator: rk808: Return REGULATOR_MODE_INVALID for invalid mode
-EINVAL is not a valid return value for .of_map_mode, return
REGULATOR_MODE_INVALID instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190711122138.5221-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Wed, 26 Jun 2019 13:26:32 +0000 (21:26 +0800)]
regulator: lm363x: Fix n_voltages setting for lm36274
According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:
VPOS voltage (50-mV steps): VPOS = 4 V + (Code × 50 mV), 6.5 V max
000000 = 4 V
000001 = 4.05 V
:
011110 = 5.5 V (Default)
:
110010 = 6.5 V
110011 to 111111 map to 6.5 V
So the LM36274_LDO_VSEL_MAX should be
0b110010 (0x32).
The valid selectors are 0 ... LM36274_LDO_VSEL_MAX, n_voltages should be
LM36274_LDO_VSEL_MAX + 1. Similarly, the n_voltages should be
LM36274_BOOST_VSEL_MAX + 1 for LM36274_BOOST.
Fixes:
bff5e8071533 ("regulator: lm363x: Add support for LM36274")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Axel Lin [Wed, 26 Jun 2019 13:26:31 +0000 (21:26 +0800)]
regulator: lm363x: Fix off-by-one n_voltages for lm3632 ldo_vpos/ldo_vneg
According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V
The LM3632_LDO_VSEL_MAX should be
0b101000 (0x28), so the maximum voltage
can match the datasheet.
Fixes:
3a8d1a73a037 ("regulator: add LM363X driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Sun, 21 Jul 2019 21:05:38 +0000 (14:05 -0700)]
Linus 5.3-rc1
Linus Torvalds [Sun, 21 Jul 2019 17:28:39 +0000 (10:28 -0700)]
Merge tag 'devicetree-fixes-for-5.3' of git://git./linux/kernel/git/robh/linux
Pull Devicetree fixes from Rob Herring:
"Fix several warnings/errors in validation of binding schemas"
* tag 'devicetree-fixes-for-5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
dt-bindings: iio: ad7124: Fix dtc warnings in example
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
dt-bindings: Ensure child nodes are of type 'object'
Linus Torvalds [Sun, 21 Jul 2019 17:09:43 +0000 (10:09 -0700)]
Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs
Pull vfs documentation typo fix from Al Viro.
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
typo fix: it's d_make_root, not d_make_inode...
Linus Torvalds [Sun, 21 Jul 2019 17:01:17 +0000 (10:01 -0700)]
Merge tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes from Steve French:
"Two fixes for stable, one that had dependency on earlier patch in this
merge window and can now go in, and a perf improvement in SMB3 open"
* tag '5.3-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module number
cifs: flush before set-info if we have writeable handles
smb3: optimize open to not send query file internal info
cifs: copy_file_range needs to strip setuid bits and update timestamps
CIFS: fix deadlock in cached root handling
Qian Cai [Thu, 11 Jul 2019 16:17:45 +0000 (12:17 -0400)]
iommu/amd: fix a crash in iova_magazine_free_pfns
The commit
b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops
method") incorrectly changed the checking from dma_ops_alloc_iova() in
map_sg() causes a crash under memory pressure as dma_ops_alloc_iova()
never return DMA_MAPPING_ERROR on failure but 0, so the error handling
is all wrong.
kernel BUG at drivers/iommu/iova.c:801!
Workqueue: kblockd blk_mq_run_work_fn
RIP: 0010:iova_magazine_free_pfns+0x7d/0xc0
Call Trace:
free_cpu_cached_iovas+0xbd/0x150
alloc_iova_fast+0x8c/0xba
dma_ops_alloc_iova.isra.6+0x65/0xa0
map_sg+0x8c/0x2a0
scsi_dma_map+0xc6/0x160
pqi_aio_submit_io+0x1f6/0x440 [smartpqi]
pqi_scsi_queue_command+0x90c/0xdd0 [smartpqi]
scsi_queue_rq+0x79c/0x1200
blk_mq_dispatch_rq_list+0x4dc/0xb70
blk_mq_sched_dispatch_requests+0x249/0x310
__blk_mq_run_hw_queue+0x128/0x200
blk_mq_run_work_fn+0x27/0x30
process_one_work+0x522/0xa10
worker_thread+0x63/0x5b0
kthread+0x1d2/0x1f0
ret_from_fork+0x22/0x40
Fixes:
b3aa14f02254 ("iommu: remove the mapping_error dma_map_ops method")
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Mike Rapoport [Tue, 30 Apr 2019 14:27:50 +0000 (17:27 +0300)]
hexagon: switch to generic version of pte allocation
The hexagon implementation pte_alloc_one(), pte_alloc_one_kernel(),
pte_free_kernel() and pte_free() is identical to the generic except of
lack of __GFP_ACCOUNT for the user PTEs allocation.
Switch hexagon to use generic version of these functions.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 21 Jul 2019 16:46:59 +0000 (09:46 -0700)]
Merge tag 'ntb-5.3' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"New feature to add support for NTB virtual MSI interrupts, the ability
to test and use this feature in the NTB transport layer.
Also, bug fixes for the AMD and Switchtec drivers, as well as some
general patches"
* tag 'ntb-5.3' of git://github.com/jonmason/ntb: (22 commits)
NTB: Describe the ntb_msi_test client in the documentation.
NTB: Add MSI interrupt support to ntb_transport
NTB: Add ntb_msi_test support to ntb_test
NTB: Introduce NTB MSI Test Client
NTB: Introduce MSI library
NTB: Rename ntb.c to support multiple source files in the module
NTB: Introduce functions to calculate multi-port resource index
NTB: Introduce helper functions to calculate logical port number
PCI/switchtec: Add module parameter to request more interrupts
PCI/MSI: Support allocating virtual MSI interrupts
ntb_hw_switchtec: Fix setup MW with failure bug
ntb_hw_switchtec: Skip unnecessary re-setup of shared memory window for crosslink case
ntb_hw_switchtec: Remove redundant steps of switchtec_ntb_reinit_peer() function
NTB: correct ntb_dev_ops and ntb_dev comment typos
NTB: amd: Silence shift wrapping warning in amd_ntb_db_vector_mask()
ntb_hw_switchtec: potential shift wrapping bug in switchtec_ntb_init_sndev()
NTB: ntb_transport: Ensure qp->tx_mw_dma_addr is initaliazed
NTB: ntb_hw_amd: set peer limit register
NTB: ntb_perf: Clear stale values in doorbell and command SPAD register
NTB: ntb_perf: Disable NTB link after clearing peer XLAT registers
...
Al Viro [Sun, 21 Jul 2019 03:17:30 +0000 (23:17 -0400)]
typo fix: it's d_make_root, not d_make_inode...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Rob Herring [Tue, 16 Jul 2019 21:34:40 +0000 (15:34 -0600)]
dt-bindings: pinctrl: stm32: Fix missing 'clocks' property in examples
Now that examples are validated against the DT schema, an error with
required 'clocks' property missing is exposed:
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@
40020000: gpio@0: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@
50020000: gpio@1000: 'clocks' is a required property
Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.example.dt.yaml: \
pinctrl@
50020000: gpio@2000: 'clocks' is a required property
Add the missing 'clocks' properties to the examples to fix the errors.
Fixes:
2c9239c125f0 ("dt-bindings: pinctrl: Convert stm32 pinctrl bindings to json-schema")
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Tue, 16 Jul 2019 20:21:56 +0000 (14:21 -0600)]
dt-bindings: iio: ad7124: Fix dtc warnings in example
With the conversion to DT schema, the examples are now compiled with
dtc. The ad7124 binding example has the following warning:
Documentation/devicetree/bindings/iio/adc/adi,ad7124.example.dts:19.11-21: \
Warning (reg_format): /example-0/adc@0:reg: property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
There's a default #size-cells and #address-cells values of 1 for
examples. For examples needing different values such as this one on a
SPI bus, they need to provide a SPI bus parent node.
Fixes:
26ae15e62d3c ("Convert AD7124 bindings documentation to YAML format.")
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Tue, 16 Jul 2019 20:13:29 +0000 (14:13 -0600)]
dt-bindings: iio: avia-hx711: Fix avdd-supply typo in example
Now that examples are validated against the DT schema, a typo in
avia-hx711 example generates a warning:
Documentation/devicetree/bindings/iio/adc/avia-hx711.example.dt.yaml: weight: 'avdd-supply' is a required property
Fix the typo.
Fixes:
5150ec3fe125 ("avia-hx711.yaml: transform DT binding to YAML")
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 15 Jul 2019 22:48:41 +0000 (16:48 -0600)]
dt-bindings: pinctrl: aspeed: Fix AST2500 example errors
The schema examples are now validated against the schema itself. The
AST2500 pinctrl schema has a couple of errors:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
example-0: $nodename:0: 'example-0' does not match '^(bus|soc|axi|ahb|apb)(@[0-9a-f]+)?$'
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.example.dt.yaml: \
pinctrl: aspeed,external-nodes: [[1, 2]] is too short
Fixes:
0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Mon, 15 Jul 2019 22:37:25 +0000 (16:37 -0600)]
dt-bindings: pinctrl: aspeed: Fix 'compatible' schema errors
The Aspeed pinctl schema have errors in the 'compatible' schema:
Documentation/devicetree/bindings/pinctrl/aspeed,ast2400-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2400-pinctrl', 'aspeed', 'g4-pinctrl'] has non-unique elements
Documentation/devicetree/bindings/pinctrl/aspeed,ast2500-pinctrl.yaml: \
properties:compatible:enum: ['aspeed', 'ast2500-pinctrl', 'aspeed', 'g5-pinctrl'] has non-unique elements
Flow style sequences have to be quoted if the vales contain ','. Fix
this by using the more common one line per entry formatting.
Fixes:
0a617de16730 ("dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema")
Fixes:
07457937bb5c ("dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema")
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Joel Stanley <joel@jms.id.au>
Cc: linux-aspeed@lists.ozlabs.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 26 Jun 2019 23:57:59 +0000 (17:57 -0600)]
dt-bindings: riscv: Limit cpus schema to only check RiscV 'cpu' nodes
Matching on the 'cpus' node was a bad choice because the schema is
incorrectly applied to non-RiscV cpus nodes. As we now have a common cpus
schema which checks the general structure, it is also redundant to do so
in the Risc-V CPU schema.
The downside is one could conceivably mix different architecture's cpu
nodes or have typos in the compatible string. The latter problem pretty
much exists for every schema.
Acked-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Rob Herring [Wed, 3 Jul 2019 20:17:06 +0000 (14:17 -0600)]
dt-bindings: Ensure child nodes are of type 'object'
Properties which are child node definitions need to have an explict
type. Otherwise, a matching (DT) property can silently match when an
error is desired. Fix this up tree-wide. Once this is fixed, the
meta-schema will enforce this on any child node definitions.
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Cc: linux-spi@vger.kernel.org
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Linus Torvalds [Sat, 20 Jul 2019 19:22:30 +0000 (12:22 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull more input updates from Dmitry Torokhov:
- Apple SPI keyboard and trackpad driver for newer Macs
- ALPS driver will ignore trackpoint-only devices to give the
trackpoint driver a chance to handle them properly
- another Lenovo is switched over to SMbus from PS/2
- assorted driver fixups.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - fix a mismatch between a condition check and its comment
Input: psmouse - fix build error of multiple definition
Input: applespi - remove set but not used variables 'sts'
Input: add Apple SPI keyboard and trackpad driver
Input: alps - don't handle ALPS cs19 trackpoint-only device
Input: hyperv-keyboard - remove dependencies on PAGE_SIZE for ring buffer
Input: adp5589 - initialize GPIO controller parent device
Input: iforce - remove empty multiline comments
Input: synaptics - fix misuse of strlcpy
Input: auo-pixcir-ts - switch to using devm_add_action_or_reset()
Input: gtco - bounds check collection indent level
Input: mtk-pmic-keys - add of_node_put() before return
Input: sun4i-lradc-keys - add of_node_put() before return
Input: synaptics - whitelist Lenovo T580 SMBus intertouch
Linus Torvalds [Sat, 20 Jul 2019 19:09:52 +0000 (12:09 -0700)]
Merge tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
"Fix various regressions:
- force unencrypted dma-coherent buffers if encryption bit can't fit
into the dma coherent mask (Tom Lendacky)
- avoid limiting request size if swiotlb is not used (me)
- fix swiotlb handling in dma_direct_sync_sg_for_cpu/device (Fugang
Duan)"
* tag 'dma-mapping-5.3-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-direct: correct the physical addr in dma_direct_sync_sg_for_cpu/device
dma-direct: only limit the mapping size if swiotlb could be used
dma-mapping: add a dma_addressing_limited helper
dma-direct: Force unencrypted DMA under SME for certain DMA masks
Linus Torvalds [Sat, 20 Jul 2019 18:24:49 +0000 (11:24 -0700)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 specific fixes and updates:
- The CR2 corruption fixes which store CR2 early in the entry code
and hand the stored address to the fault handlers.
- Revert a forgotten leftover of the dropped FSGSBASE series.
- Plug a memory leak in the boot code.
- Make the Hyper-V assist functionality robust by zeroing the shadow
page.
- Remove a useless check for dead processes with LDT
- Update paravirt and VMware maintainers entries.
- A few cleanup patches addressing various compiler warnings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry/64: Prevent clobbering of saved CR2 value
x86/hyper-v: Zero out the VP ASSIST PAGE on allocation
x86, boot: Remove multiple copy of static function sanitize_boot_params()
x86/boot/compressed/64: Remove unused variable
x86/boot/efi: Remove unused variables
x86/mm, tracing: Fix CR2 corruption
x86/entry/64: Update comments and sanity tests for create_gap
x86/entry/64: Simplify idtentry a little
x86/entry/32: Simplify common_exception
x86/paravirt: Make read_cr2() CALLEE_SAVE
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
x86/process: Delete useless check for dead process with LDT
x86: math-emu: Hide clang warnings for 16-bit overflow
x86/e820: Use proper booleans instead of 0/1
x86/apic: Silence -Wtype-limits compiler warnings
x86/mm: Free sme_early_buffer after init
x86/boot: Fix memory leak in default_get_smp_config()
Revert "x86/ptrace: Prevent ptrace from clearing the FS/GS selector" and fix the test
Linus Torvalds [Sat, 20 Jul 2019 18:06:12 +0000 (11:06 -0700)]
Merge branch 'perf-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull perf tooling updates from Thomas Gleixner:
"A set of perf improvements and fixes:
perf db-export:
- Improvements in how COMM details are exported to databases for post
processing and use in the sql-viewer.py UI.
- Export switch events to the database.
BPF:
- Bump rlimit(MEMLOCK) for 'perf test bpf' and 'perf trace', just
like selftests/bpf/bpf_rlimit.h do, which makes errors due to
exhaustion of this limit, which are kinda cryptic (EPERM sometimes)
less frequent.
perf version:
- Fix segfault due to missing OPT_END(), noticed on PowerPC.
perf vendor events:
- Add JSON files for IBM s/390 machine type 8561.
perf cs-etm (ARM):
- Fix two cases of error returns not bing done properly: Invalid
ERR_PTR() use and loss of propagation error codes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
perf version: Fix segfault due to missing OPT_END()
perf vendor events s390: Add JSON files for machine type 8561
perf cs-etm: Return errcode in cs_etm__process_auxtrace_info()
perf cs-etm: Remove errnoeous ERR_PTR() usage in cs_etm__process_auxtrace_info
perf scripts python: export-to-postgresql.py: Export switch events
perf scripts python: export-to-sqlite.py: Export switch events
perf db-export: Export switch events
perf db-export: Factor out db_export__threads()
perf script: Add scripting operation process_switch()
perf scripts python: exported-sql-viewer.py: Use new 'has_calls' column
perf scripts python: exported-sql-viewer.py: Remove redundant semi-colons
perf scripts python: export-to-postgresql.py: Add has_calls column to comms table
perf scripts python: export-to-sqlite.py: Add has_calls column to comms table
perf db-export: Also export thread's current comm
perf db-export: Factor out db_export__comm()
perf scripts python: export-to-postgresql.py: Export comm details
perf scripts python: export-to-sqlite.py: Export comm details
perf db-export: Export comm details
perf db-export: Fix a white space issue in db_export__sample()
perf db-export: Move export__comm_thread into db_export__sample()
...
Linus Torvalds [Sat, 20 Jul 2019 17:45:15 +0000 (10:45 -0700)]
Merge branch 'core-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
- A collection of objtool fixes which address recent fallout partially
exposed by newer toolchains, clang, BPF and general code changes.
- Force USER_DS for user stack traces
[ Note: the "objtool fixes" are not all to objtool itself, but for
kernel code that triggers objtool warnings.
Things like missing function size annotations, or code that confuses
the unwinder etc. - Linus]
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
objtool: Support conditional retpolines
objtool: Convert insn type to enum
objtool: Fix seg fault on bad switch table entry
objtool: Support repeated uses of the same C jump table
objtool: Refactor jump table code
objtool: Refactor sibling call detection logic
objtool: Do frame pointer check before dead end check
objtool: Change dead_end_function() to return boolean
objtool: Warn on zero-length functions
objtool: Refactor function alias logic
objtool: Track original function across branches
objtool: Add mcsafe_handle_tail() to the uaccess safe list
bpf: Disable GCC -fgcse optimization for ___bpf_prog_run()
x86/uaccess: Remove redundant CLACs in getuser/putuser error paths
x86/uaccess: Don't leak AC flag into fentry from mcsafe_handle_tail()
x86/uaccess: Remove ELF function annotation from copy_user_handle_tail()
x86/head/64: Annotate start_cpu0() as non-callable
x86/entry: Fix thunk function ELF sizes
x86/kvm: Don't call kvm_spurious_fault() from .fixup
x86/kvm: Replace vmx_vmenter()'s call to kvm_spurious_fault() with UD2
...
Linus Torvalds [Sat, 20 Jul 2019 17:43:03 +0000 (10:43 -0700)]
Merge branch 'smp-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull smp fix from Thomas Gleixner:
"Add warnings to the smp function calls so callers from wrong contexts
get detected"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp: Warn on function calls from softirq context
Linus Torvalds [Sat, 20 Jul 2019 17:33:44 +0000 (10:33 -0700)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull CONFIG_PREEMPT_RT stub config from Thomas Gleixner:
"The real-time preemption patch set exists for almost 15 years now and
while the vast majority of infrastructure and enhancements have found
their way into the mainline kernel, the final integration of RT is
still missing.
Over the course of the last few years, we have worked on reducing the
intrusivenness of the RT patches by refactoring kernel infrastructure
to be more real-time friendly. Almost all of these changes were
benefitial to the mainline kernel on their own, so there was no
objection to integrate them.
Though except for the still ongoing printk refactoring, the remaining
changes which are required to make RT a first class mainline citizen
are not longer arguable as immediately beneficial for the mainline
kernel. Most of them are either reordering code flows or adding RT
specific functionality.
But this now has hit a wall and turned into a classic hen and egg
problem:
Maintainers are rightfully wary vs. these changes as they make only
sense if the final integration of RT into the mainline kernel takes
place.
Adding CONFIG_PREEMPT_RT aims to solve this as a clear sign that RT
will be fully integrated into the mainline kernel. The final
integration of the missing bits and pieces will be of course done with
the same careful approach as we have used in the past.
While I'm aware that you are not entirely enthusiastic about that, I
think that RT should receive the same treatment as any other widely
used out of tree functionality, which we have accepted into mainline
over the years.
RT has become the de-facto standard real-time enhancement and is
shipped by enterprise, embedded and community distros. It's in use
throughout a wide range of industries: telecommunications, industrial
automation, professional audio, medical devices, data acquisition,
automotive - just to name a few major use cases.
RT development is backed by a Linuxfoundation project which is
supported by major stakeholders of this technology. The funding will
continue over the actual inclusion into mainline to make sure that the
functionality is neither introducing regressions, regressing itself,
nor becomes subject to bitrot. There is also a lifely user community
around RT as well, so contrary to the grim situation 5 years ago, it's
a healthy project.
As RT is still a good vehicle to exercise rarely used code paths and
to detect hard to trigger issues, you could at least view it as a QA
tool if nothing else"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/rt, Kconfig: Introduce CONFIG_PREEMPT_RT
Linus Torvalds [Sat, 20 Jul 2019 17:20:27 +0000 (10:20 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull more KVM updates from Paolo Bonzini:
"Mostly bugfixes, but also:
- s390 support for KVM selftests
- LAPIC timer offloading to housekeeping CPUs
- Extend an s390 optimization for overcommitted hosts to all
architectures
- Debugging cleanups and improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: x86: Add fixed counters to PMU filter
KVM: nVMX: do not use dangling shadow VMCS after guest reset
KVM: VMX: dump VMCS on failed entry
KVM: x86/vPMU: refine kvm_pmu err msg when event creation failed
KVM: s390: Use kvm_vcpu_wake_up in kvm_s390_vcpu_wakeup
KVM: Boost vCPUs that are delivering interrupts
KVM: selftests: Remove superfluous define from vmx.c
KVM: SVM: Fix detection of AMD Errata 1096
KVM: LAPIC: Inject timer interrupt via posted interrupt
KVM: LAPIC: Make lapic timer unpinned
KVM: x86/vPMU: reset pmc->counter to 0 for pmu fixed_counters
KVM: nVMX: Ignore segment base for VMX memory operand when segment not FS or GS
kvm: x86: ioapic and apic debug macros cleanup
kvm: x86: some tsc debug cleanup
kvm: vmx: fix coccinelle warnings
x86: kvm: avoid constant-conversion warning
x86: kvm: avoid -Wsometimes-uninitized warning
KVM: x86: expose AVX512_BF16 feature to guest
KVM: selftests: enable pgste option for the linker on s390
KVM: selftests: Move kvm_create_max_vcpus test to generic code
...
Linus Torvalds [Sat, 20 Jul 2019 17:04:58 +0000 (10:04 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is the final round of mostly small fixes in our initial submit.
It's mostly minor fixes and driver updates. The only change of note is
adding a virt_boundary_mask to the SCSI host and host template to
parametrise this for NVMe devices instead of having them do a call in
slave_alloc. It's a fairly straightforward conversion except in the
two NVMe handling drivers that didn't set it who now have a virtual
infinity parameter added"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: megaraid_sas: set an unlimited max_segment_size
scsi: mpt3sas: set an unlimited max_segment_size for SAS 3.0 HBAs
scsi: IB/srp: set virt_boundary_mask in the scsi host
scsi: IB/iser: set virt_boundary_mask in the scsi host
scsi: storvsc: set virt_boundary_mask in the scsi host template
scsi: ufshcd: set max_segment_size in the scsi host template
scsi: core: take the DMA max mapping size into account
scsi: core: add a host / host template field for the virt boundary
scsi: core: Fix race on creating sense cache
scsi: sd_zbc: Fix compilation warning
scsi: libfc: fix null pointer dereference on a null lport
scsi: zfcp: fix GCC compiler warning emitted with -Wmaybe-uninitialized
scsi: zfcp: fix request object use-after-free in send path causing wrong traces
scsi: zfcp: fix request object use-after-free in send path causing seqno errors
scsi: megaraid_sas: Update driver version to 07.710.50.00
scsi: megaraid_sas: Add module parameter for FW Async event logging
scsi: megaraid_sas: Enable msix_load_balance for Invader and later controllers
scsi: megaraid_sas: Fix calculation of target ID
scsi: lpfc: reduce stack size with CONFIG_GCC_PLUGIN_STRUCTLEAK_VERBOSE
scsi: devinfo: BLIST_TRY_VPD_PAGES for SanDisk Cruzer Blade
...
Linus Torvalds [Sat, 20 Jul 2019 16:34:55 +0000 (09:34 -0700)]
Merge tag 'kbuild-v5.3-2' of git://git./linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- match the directory structure of the linux-libc-dev package to that
of Debian-based distributions
- fix incorrect include/config/auto.conf generation when Kconfig
creates it along with the .config file
- remove misleading $(AS) from documents
- clean up precious tag files by distclean instead of mrproper
- add a new coccinelle patch for devm_platform_ioremap_resource
migration
- refactor module-related scripts to read modules.order instead of
$(MODVERDIR)/*.mod files to get the list of created modules
- remove MODVERDIR
- update list of header compile-test
- add -fcf-protection=none flag to avoid conflict with the retpoline
flags when CONFIG_RETPOLINE=y
- misc cleanups
* tag 'kbuild-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: add -fcf-protection=none when using retpoline flags
kbuild: update compile-test header list for v5.3-rc1
kbuild: split out *.mod out of {single,multi}-used-m rules
kbuild: remove 'prepare1' target
kbuild: remove the first line of *.mod files
kbuild: create *.mod with full directory path and remove MODVERDIR
kbuild: export_report: read modules.order instead of .tmp_versions/*.mod
kbuild: modpost: read modules.order instead of $(MODVERDIR)/*.mod
kbuild: modsign: read modules.order instead of $(MODVERDIR)/*.mod
kbuild: modinst: read modules.order instead of $(MODVERDIR)/*.mod
scsi: remove pointless $(MODVERDIR)/$(obj)/53c700.ver
kbuild: remove duplication from modules.order in sub-directories
kbuild: get rid of kernel/ prefix from in-tree modules.{order,builtin}
kbuild: do not create empty modules.order in the prepare stage
coccinelle: api: add devm_platform_ioremap_resource script
kbuild: compile-test headers listed in header-test-m as well
kbuild: remove unused hostcc-option
kbuild: remove tag files by distclean instead of mrproper
kbuild: add --hash-style= and --build-id unconditionally
kbuild: get rid of misleading $(AS) from documents
...
Linus Torvalds [Sat, 20 Jul 2019 16:15:51 +0000 (09:15 -0700)]
Merge branch 'work.dcache2' of git://git./linux/kernel/git/viro/vfs
Pull dcache and mountpoint updates from Al Viro:
"Saner handling of refcounts to mountpoints.
Transfer the counting reference from struct mount ->mnt_mountpoint
over to struct mountpoint ->m_dentry. That allows us to get rid of the
convoluted games with ordering of mount shutdowns.
The cost is in teaching shrink_dcache_{parent,for_umount} to cope with
mixed-filesystem shrink lists, which we'll also need for the Slab
Movable Objects patchset"
* 'work.dcache2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
switch the remnants of releasing the mountpoint away from fs_pin
get rid of detach_mnt()
make struct mountpoint bear the dentry reference to mountpoint, not struct mount
Teach shrink_dcache_parent() to cope with mixed-filesystem shrink lists
fs/namespace.c: shift put_mountpoint() to callers of unhash_mnt()
__detach_mounts(): lookup_mountpoint() can't return ERR_PTR() anymore
nfs: dget_parent() never returns NULL
ceph: don't open-code the check for dead lockref
Thomas Gleixner [Sat, 20 Jul 2019 08:56:41 +0000 (10:56 +0200)]
x86/entry/64: Prevent clobbering of saved CR2 value
The recent fix for CR2 corruption introduced a new way to reliably corrupt
the saved CR2 value.
CR2 is saved early in the entry code in RDX, which is the third argument to
the fault handling functions. But it missed that between saving and
invoking the fault handler enter_from_user_mode() can be called. RDX is a
caller saved register so the invoked function can freely clobber it with
the obvious consequences.
The TRACE_IRQS_OFF call is safe as it calls through the thunk which
preserves RDX, but TRACE_IRQS_OFF_DEBUG is not because it also calls into
C-code outside of the thunk.
Store CR2 in R12 instead which is a callee saved register and move R12 to
RDX just before calling the fault handler.
Fixes:
a0d14b8909de ("x86/mm, tracing: Fix CR2 corruption")
Reported-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1907201020540.1782@nanos.tec.linutronix.de
Peter Zijlstra [Thu, 18 Jul 2019 09:20:09 +0000 (11:20 +0200)]
smp: Warn on function calls from softirq context
It's clearly documented that smp function calls cannot be invoked from
softirq handling context. Unfortunately nothing enforces that or emits a
warning.
A single function call can be invoked from softirq context only via
smp_call_function_single_async().
The only legit context is task context, so add a warning to that effect.
Reported-by: luferry <luferry@163.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20190718160601.GP3402@hirez.programming.kicks-ass.net
Eric Hankland [Thu, 18 Jul 2019 18:38:18 +0000 (11:38 -0700)]
KVM: x86: Add fixed counters to PMU filter
Updates KVM_CAP_PMU_EVENT_FILTER so it can also whitelist or blacklist
fixed counters.
Signed-off-by: Eric Hankland <ehankland@google.com>
[No need to check padding fields for zero. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Fri, 19 Jul 2019 16:41:10 +0000 (18:41 +0200)]
KVM: nVMX: do not use dangling shadow VMCS after guest reset
If a KVM guest is reset while running a nested guest, free_nested will
disable the shadow VMCS execution control in the vmcs01. However,
on the next KVM_RUN vmx_vcpu_run would nevertheless try to sync
the VMCS12 to the shadow VMCS which has since been freed.
This causes a vmptrld of a NULL pointer on my machime, but Jan reports
the host to hang altogether. Let's see how much this trivial patch fixes.
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Liran Alon <liran.alon@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Fri, 19 Jul 2019 16:15:08 +0000 (18:15 +0200)]
KVM: VMX: dump VMCS on failed entry
This is useful for debugging, and is ratelimited nowadays.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Like Xu [Thu, 18 Jul 2019 05:35:14 +0000 (13:35 +0800)]
KVM: x86/vPMU: refine kvm_pmu err msg when event creation failed
If a perf_event creation fails due to any reason of the host perf
subsystem, it has no chance to log the corresponding event for guest
which may cause abnormal sampling data in guest result. In debug mode,
this message helps to understand the state of vPMC and we may not
limit the number of occurrences but not in a spamming style.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Like Xu <like.xu@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>