dt-bindings: firmware: qcom: scm: add SSC_Q6 and ADSP_Q6 VMIDs

SSC_Q6 and ADSP_Q6 are used in the FastRPC driver for accessing
the secure world.

Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-3-me@dylanvanassche.be

arm64: dts: qcom: sdm845: add SLPI remoteproc

Add the SLPI remoteproc to the SDM845 Qualcomm SoC which is responsible
for exposing the sensors connected to the SoC. The SLPI communicates
over GLink edge 'dsps' and is similar to other DSPs e.g. ADSP or CDSP.
This patch allows the SLPI to boot and expose itself over QRTR as
service 400.

Signed-off-by: Dylan Van Assche <me@dylanvanassche.be>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406173148.28309-2-me@dylanvanassche.be

arm64: dts: qcom: sa8775p-ride: add PMIC regulators

Add PMIC regulators for sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230406192811.460888-4-brgl@bgdev.pl

arm64: dts: qcom: sdm845-oneplus: Fix speaker GPIO node

Drop the unnecessary mux{} level to make dtbs check happy.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-6-6efb4196f51f@linaro.org

arm64: dts: qcom: pm8916: Fix pm8941-misc node name

Fix the node name to make dtbs_check happy:

qcom/apq8016-sbc.dtb: pmic@0: 'extcon@1300' does not match any of the
regexes: '(.*)?(wled|leds)@[0-9a-f]+$', '^adc-tm@[0-9a-f]+$',
'^adc@[0-9a-f]+$', '^audio-codec@[0-9a-f]+$', '^charger@[0-9a-f]+$',
'^mpps@[0-9a-f]+$', '^nvram@[0-9a-f]+$', '^rtc@[0-9a-f]+$',
'^temp-alarm@[0-9a-f]+$', '^usb-detect@[0-9a-f]+$',
'^usb-vbus-regulator@[0-9a-f]+$', '^vibrator@[0-9a-f]+$',
'gpio@[0-9a-f]+$', 'pinctrl-[0-9]+', 'pon@[0-9a-f]+$'

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-5-6efb4196f51f@linaro.org

arm64: dts: qcom: sc7280: Fix up the gic node

Fix the following schema warning:

gic-its@17a40000: False schema does not allow {'compatible':
['arm,gic-v3-its'], 'msi-controller': True, '#msi-cells': [[1]],
'reg': [[0, 396623872, 0, 131072]], 'status': ['disabled']}

And reorder the properties to be more in order with all other nodes.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230407-topic-msm_dtb-v1-4-6efb4196f51f@linaro.org

arm64: dts: qcom: sdm845: Fix cheza qspi pin config

Cheza's SPI flash hookups (qspi) are exactly the same as trogdor's.
Apply the same solution that's described in the patch ("arm64: dts:
qcom: sc7180: Fix trogdor qspi pin config")

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.14.I82951106ab8170f973a4c1c7d9b034655bbe2f60@changeid

arm64: dts: qcom: sc7280: Fix qspi pin config

Similar to sc7180 (see the patch ("arm64: dts: qcom: sc7180: Fix
trogdor qspi pin config")), we should adjust the qspi pin config for
sc7280.

I won't re-describe all the research/arguments in the sc7180 patch
here, but there are a few differences for sc7280 worth noting:

1. On herobrine the SPI flash (qspi) is wired up differently on the
   board. Rather than Cr50 and the AP being wired directly together,
   there's actually a mux that will _either_ connect the AP to the
   flash or Cr50 to the flash. This means that the internal pulls on
   Cr50 don't affect us and we should enable our own pulldowns.

2. On herobrine, EEs added an external pulldown on the MISO line. The
   argument in the schematic said that we added it (but not one on
   MOSI and CLK) because Cr50 already enabled pulldowns on MOSI and
   CLK. ...though, as per #1, those Cr50 pulldowns would only affect
   the line when the mux was swung to Cr50.

The ironic result of #1 and #2 is that the external pulldowns on
CLK/MISO/MOSI on herobrine are _exactly opposite_ of the ones on
trogdor.

3. While I still don't have the actual exact schematics for all
   variants of IDP/CRD that were produced, I have some reference
   schematics that give me a belief of how the qspi is hooked up
   there. From this, I'm fairly certain that all of the older variants
   of IDP/CRD either have a pulldown on the CLK/MOSI/MISO lines (maybe
   through a direct connect to Cr50) or have no pull (in other words,
   they don't have a pullup). I'll go ahead and enable internal
   pulldowns on all the lines since that won't hurt to double-pull if
   there's an external pulldown and it's nice to have a pulldown if
   there's nothing external. Note that this only affects _older_
   CRDs. Newer revs are considered "herobrine" (see the hoglin/zoglin
   device trees).

4. I didn't find the same strange "auto-switch-to-keeper" at suspend
   when probing on sc7280. Whatever pulls (or lack thereof) I left at
   suspend time seemed to persist into suspend.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.13.Ib44c3e417c414a4227db8def75ded37ad368212c@changeid

arm64: dts: qcom: sc7180: Fix trogdor qspi pin config

In commit 7ec3e67307f8 ("arm64: dts: qcom: sc7180-trogdor: add initial
trogdor and lazor dt") we specified the pull settings on the boot SPI
(the qspi) data lines as pullups to "park" the lines. This seemed like
the right thing to do, but I never really probed the lines to confirm.

Since that time, I've done A LOT of research, experiements and poking
of the lines with a voltmeter.

A first batch of discoveries:
- There is an external pullup on CS (clearly shown on schematics)
- There are weak external pulldowns on CLK/MOSI (believed to be Cr50's
  internal pulldowns)
- There is no pull on MISO.
- When qspi isn't actively transferring it still drives CS, CLK, and
  MOSI. CS and MOSI are driven high and CLK is driven low. It does not
  drive MISO and (if no internal pulls are enabled) the line floats.

The above means that it's good to have some sort of pull on MISO, at
the very least. The pullup that we had before was actually fine (and
my voltmeter confirms that it actually affected the state of the pin)
but a pulldown would work equally well (and would match MOSI and CLK
better).

The above also means that we could save a tiny bit of power (not
measurable by my setup) by setting up a sleep state for these pins. If
nothing else this prevents us from driving high against Cr50's
internal pulldown on MOSI. However, Qualcomm has also asserted in the
past that it burns a little extra power to drive a pin, especially
since these are configured with a slightly higher drive strength

Let's fix all this. Since the external pulls are different for the two
data lines, we'll split them into separate configs. Then we'll change
the MISO pin to a pulldown and add a sleep state.

On a slightly tangental (but not totally unrelated note), I also
discovered some interesting things with these pins in suspend. First,
I found that if we don't switch the pins to GPIO that the qspi
peripheral continues to drive them in suspend. That'll be solved by
what we're already doing above. Second, I found that something in the
system suspend path (after Linux stops running) reconfigures these
pins so that they don't have their normal pulls enabled but instead
change to "keepers" (bias-bus-hold in DT speak). If a pin was floating
before we entered suspend then it would stop floating. I found that I
could manually pull a pin to a different level and then probe it and
it would stay there. This is exactly keeper behavior. With the
solution we have the switch to "keeper" doesn't matter too much but
it's good to document.

While talking about "keepers", it can also be noted that I found that
the "keepers" on these pins were at least enough to win a fight
against Cr50's internal pulls. That means it's best to make sure that
the state of the pins are already correct before the mysterious
transition to a keeper. Otherwise we'll burn (a small amount of) power
in S3 via this fight. Luckily with the current solution we don't hit
this case.

NOTE: I've left "sc7180-idp" behavior totally alone in this patch. I
didn't add a sleep state and I didn't change any pulls--I just adapted
it to the fact that the data lines have separate configs. Qualcomm
doesn't provide me with schematics for IDP and thus I don't actually
know how the pulls are configured. Since this is just a development
platform and worked well enough, it seems safer to leave it alone.

Dependencies:
- This patch has a hard dependency on ("pinctrl: qcom: Support
  OUTPUT_ENABLE; deprecate INPUT_ENABLE"). Something in the boot code
  seemed to have been confused and thought it needed to set the
  "OUTPUT ENABLE" bit for these pins even though it was using them as
  SPI. Thus if we don't honor the "output-disable" property we could
  end up driving the SPI pins while in sleep mode.
- In general, it's probably best not to backport this to a kernel that
  doesn't have commit d21f4b7ffc22 ("pinctrl: qcom: Avoid glitching
  lines when we first mux to output"). That landed a while ago, but
  it's still good to be explicit in case someone was backporting. If
  we don't have that then there might be a glitch when we first switch
  over to GPIO before we disable the output.
- This patch _doesn't_ really have any dependency on the qspi driver
  patch that supports setting the pinctrl sleep state--they can go in
  either order. If we define the sleep state and the driver never
  selects it that's fine. If the driver tries to select a sleep state
  that we don't define that's fine.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.12.I6f03f86546e6ce9abb1d24fd9ece663c3a5b950c@changeid

arm64: dts: qcom: sdm845: Remove superfluous "input-enable"s from cheza

As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.

Looking at cheza
* ec_ap_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
  as inputs automatically by the Linux GPIO subsystem (presumably the
  reference for other OSes using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
  through the kernel's GPIO API and will be configured automatically.

That means that in none of the cases for cheza did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.11.Ia439c29517b1c0625325a54387b047f099d16425@changeid

arm64: dts: qcom: sc7280: Remove superfluous "input-enable"s from idp-ec-h1

As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.

Looking at the sc7280-idp-ec-h1.dtsi file:
* ap_ec_int_l, h1_ap_int_odl: Superfluous. The pins will be configured
  as inputs automatically by the Linux GPIO subsystem (presumably the
  reference for other OSes using these device trees).

That means that in none of the cases for sc7280-idp-ec-h1.dtsi did we
need to change "input-enable" to "output-disable" and we can just
remove these superfluous properties.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.10.I1343c20f4aaac8e2c1918b756f7ed66f6ceace9c@changeid

arm64: dts: qcom: sc7180: Remove superfluous "input-enable"s from trogdor

As talked about in the patch ("dt-bindings: pinctrl: qcom: tlmm should
use output-disable, not input-enable"), using "input-enable" in
pinctrl states for Qualcomm TLMM pinctrl devices was either
superfluous or there to disable a pin's output.

Looking at trogdor:
* ap_ec_int_l, fp_to_ap_irq_l, h1_ap_int_odl, p_sensor_int_l:
  Superfluous. The pins will be configured as inputs automatically by
  the Linux GPIO subsystem (presumably the reference for other OSes
  using these device trees).
* bios_flash_wp_l: Superfluous. This pin is exposed to userspace
  through the kernel's GPIO API and will be configured automatically.

That means that in none of the cases for trogdor did we need to change
"input-enable" to "output-disable" and we can just remove these
superfluous properties.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.9.I94dbc53176e8adb0d7673b7feb2368e85418f938@changeid

arm64: dts: qcom: sc7180: Annotate l13a on trogdor to always-on

The l13a rail on trogdor devices has always been intended to be
always-on on both S0 and S3. Different trogdor variants use l13a in
slightly different ways, but the overall theme is that it's a 1.8V
rail that the board uses for things that it wants powered in on S0 and
S3. On many boards this includes the boot SPI (AKA qspi).

For all intents and purposes this patch is actually a no-op since
something else in the system seems to already be keeping the rail on
all the time (confirmed via multimeter). That "something else" was
postulated to be the modem but the rail is on / stays on even without
the modem/wifi coming up so it's likely the boot config. In any case,
making the fact that this is always-on explicit seems like a good
idea.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.4.I9f47a8a53eacff6229711a827993792ceeb36971@changeid

arm64: dts: sdm845: Rename qspi data12 as data23

There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.

Fixes: e1ce853932b7 ("arm64: dts: qcom: sdm845: Add qspi (quad SPI) node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.3.I88528d037b7fda4e53a40f661be5ac61628691cd@changeid

arm64: dts: sc7280: Rename qspi data12 as data23

There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.

Fixes: 7720ea001b52 ("arm64: dts: qcom: sc7280: Add QSPI node")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.2.I4043491bb24b1e92267c5033d76cdb0fe60934da@changeid

arm64: dts: sc7180: Rename qspi data12 as data23

There are 4 qspi data pins: data0, data1, data2, and data3. Currently
we have a shared pin state for data0 and data1 (2 lane config) and a
pin state for data2 and data3 (you'd enable both this and the 2 lane
state for 4 lanes). The second state is obviously misnamed. Fix it.

Fixes: ba3fc6496366 ("arm64: dts: sc7180: Add qupv3_0 and qupv3_1")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323102605.1.Ifc1b5be04653f4ab119698a5944bfecded2080d6@changeid

Merge branch 'ib-qcom-quad-spi' of https://git./linux/kernel/git/linusw/linux-pinctrl into arm64-for-6.4

Merge the support for output-enable/disable in the pinctrl-msm driver,
to ensure that bisection across the following SC7180/SC7280 DeviceTree
changes result in something electrically sound.

Signed-off-by: Bjorn Andersson <andersson@kernel.org>

arm64: dts: qcom: Add ipq9574 SoC and AL02 board support

Add initial device tree support for Qualcomm IPQ9574 SoC and AL02 board

Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Co-developed-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Poovendhan Selvaraj <quic_poovendh@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-6-quic_devipriy@quicinc.com

Merge branch '20230316072940.29137-2-quic_devipriy@quicinc.com' into HEAD

Merge the IPQ9574 Global Clock Controller Devicetree binding, to make
available the clock definitions used in the Devicetree source.

dt-bindings: clock: Add ipq9574 clock and reset definitions

Add clock and reset ID definitions for ipq9574

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Co-developed-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Anusha Rao <quic_anusha@quicinc.com>
Signed-off-by: Devi Priya <quic_devipriy@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316072940.29137-2-quic_devipriy@quicinc.com

arm64: dts: qcom: msm8994-angler: removed clash with smem_region

This fixes memory overlap error:
[    0.000000] reserved@6300000 (0x0000000006300000--0x0000000007000000) overlaps with smem_region@6a00000 (0x0000000006a00000--0x0000000006c00000)

smem_region is the same as in downstream (qcom,smem) [1], therefore
split reserved memory into two sections on either side of smem_region.

Not adding labels as it's not expected to be used.

[1] https://android.googlesource.com/kernel/msm/+/refs/heads/android-msm-angler-3.10-marshmallow-mr1/arch/arm/boot/dts/qcom/msm8994.dtsi#948

Fixes: 380cd3a34b7f ("arm64: dts: msm8994-angler: fix the memory map")

Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131200414.24373-3-pvorel@suse.cz

arm64: dts: qcom: msm8994-angler: Fix cont_splash_mem mapping

Angler's cont_splash_mem mapping is shorter in downstream [1],
therefore 380cd3a34b7f was wrong. Obviously also 0e5ded926f2a was wrong
(workaround which fixed booting at the time).

This fixes error:
[    0.000000] memory@3401000 (0x0000000003401000--0x0000000005601000) overlaps with tzapp@4800000 (0x0000000004800000--0x0000000006100000)

[1] https://android.googlesource.com/kernel/msm/+/refs/heads/android-msm-angler-3.10-marshmallow-mr1/arch/arm64/boot/dts/huawei/huawei_msm8994_angler_row_vn1/huawei-fingerprint.dtsi#16

Fixes: 380cd3a34b7f ("arm64: dts: msm8994-angler: fix the memory map")
Fixes: 0e5ded926f2a ("arm64: dts: qcom: msm8994-angler: Disable cont_splash_mem")

Signed-off-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230131200414.24373-2-pvorel@suse.cz

MAINTAINERS: qcom: Add reviewer for Qualcomm Chromebooks

Developers on the ChromeOS team generally want to be notified to
review changes that affect Chromebook device tree files. While we
could individually add developers, the set of developers and the time
each one has available to review patches will change over time. Let's
try adding a group list as a reviewer and see if that's an effective
way to manage things.

A few notes:
* Though this email address is actually backed by a mailing list, I'm
  adding it as "R"eviewer and not "L"ist since it's not a publicly
  readable mailing list and it's intended just to have a few people on
  it. This also hopefully conveys a little more responisbility for the
  people that are part of this group.
* I've added all sc7180 and sc7280 files here. At the moment I'm not
  aware of any non-Chromebooks being supported that use these
  chips. If later something shows up then we can try to narrow down.
* I've added "sdm845-cheza" to this list but not the rest of
  "sdm845". Cheza never shipped but some developers still find the old
  developer boards useful and thus it continues to get minimal
  maintenance. Most sdm845 device tree work, however, seems to be for
  non-Chromebooks.

Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230330141051.1.If8eb4f30cb53a00a5bef1b7d3cc645c3536615ec@changeid

arm64: dts: qcom: ipq5332: add few device nodes

Add the nodes for QUP peripheral, PRNG and WDOG. While at it, enable the
I2C device for MI01.2 board.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230320104530.30411-3-quic_kathirav@quicinc.com

arm64: dts: qcom: sm8550: add ADSP audio codec macros

Add the Low Power Audio SubSystem (LPASS) / ADSP audio codec macros on
Qualcomm SM8550.  The nodes are very similar to SM8450, except missing
NPL clock which is not exposed on SM8550 and should not be touched.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230310134925.514125-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: Remove "iommus" property from PCIe nodes

Currently, most of the Qualcomm SoCs specify both "iommus" and "iommu-map"
properties for the PCIe nodes. First one passes the SMR mask to the iommu
driver and the latter specifies the SID for each PCIe device.

But with "iommus" property, the PCIe controller will be added to the
iommu group along with the devices. This makes no sense because the
controller will not initiate any DMA transaction on its own. And moreover,
it is not strictly required to pass the SMR mask to the iommu driver. If
the "iommus" property is not present, then the default mask of "0" would be
used which should work for all PCIe devices.

On the other side, if the SMR mask specified doesn't match the one expected
by the hypervisor, then all the PCIe transactions will end up triggering
"Unidentified Stream Fault" by the SMMU.

So to get rid of these hassles and also prohibit PCIe controllers from
adding to the iommu group, let's remove the "iommus" property from PCIe
nodes.

Reported-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-arm-msm/20230227195535.GA749409-robh@kernel.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230308075648.134119-1-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sm8450: simplify interrupts-extended

The parent controller for both interrupts is GIC, so no need for
interrupts-extended.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250: simplify interrupts-extended

The parent controller for the interrupt is GIC, so no need for
interrupts-extended.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp: simplify interrupts-extended

The parent controller for both interrupts is GIC, so no need for
interrupts-extended.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8450: label the Soundwire nodes

Use labels, instead of comments, for Soundwire controllers.  Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc8280xp: label the Soundwire nodes

Use labels, instead of comments, for Soundwire controllers.  Naming them
is useful, because they are specialized and have also naming in
datasheet/programming guide.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230405060906.143058-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm6115: Use the correct DSI compatible

Use the non-deprecated, SoC-specific DSI compatible.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230307-topic-dsi_qcm-v6-9-70e13b1214fa@linaro.org

arm64: dts: qcom: sc8280xp-x13s: Add bluetooth

The Lenovo Thinkpad X13s has a WCN6855 Bluetooth controller on uart2,
add this.

Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326233812.28058-5-steev@kali.org

arm64: dts: qcom: sc8280xp: Define uart2

Add the definition for uart2 for sc8280xp devices.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230326233812.28058-4-steev@kali.org

arm64: dts: qcom: sc8280xp: Add "mhi" region to the PCIe nodes

The "mhi" region contains the debug registers that could be used to monitor
the PCIe link transitions.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316081117.14288-19-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sm8250: Add "mhi" region to the PCIe nodes

The "mhi" region contains the debug registers that could be used to monitor
the PCIe link transitions.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316081117.14288-18-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sdm845: Add "mhi" region to the PCIe nodes

The "mhi" region contains the debug registers that could be used to monitor
the PCIe link transitions.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230316081117.14288-17-manivannan.sadhasivam@linaro.org

arm64: dts: qcom: sa8775p-ride: set gpio-line-names for PMIC GPIOs

Set line names for GPIO lines exposed by PMICs on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-16-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add PMIC GPIO controller nodes

Add GPIO controller nodes to PMICs that have the GPIO hooked up on
sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-15-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pmic: add thermal zones

Add the thermal zones and associated alarm nodes for the PMICs that have
them hooked up on sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-12-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pmic: add support for the pmm8654 RESIN input

Add the RESIN input for sa8775p platforms' PMIC.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-11-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pmic: add the power key

Add the power key node under the PON node for PMIC #0 on sa8775p.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-10-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add the Power On device node

Add the PON node to PMIC #0 for sa8775p platforms.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-9-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add support for the on-board PMICs

Add a new .dtsi file for sa8775p PMICs and add the four PMICs interfaced
to the SoC via SPMI. Enable the PMICs for sa8775p-ride.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-8-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add the spmi node

Add the SPMI PMIC Arbiter node for SA8775p platforms.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-6-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: add the pdc node

Add the Power Domain Controller node for SA8775p.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-5-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: sort soc nodes by reg property

Sort all children of the soc node by the first address in their reg
property. This was mostly already the case but there were some nodes
that didn't follow it so fix it now for consistency.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-3-brgl@bgdev.pl

arm64: dts: qcom: sa8775p: pad reg properties to 8 digits

The file has inconsistent padding of the address part of soc node
children's reg properties. Fix it.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230327125316.210812-2-brgl@bgdev.pl

arm64: dts: qcom: sc8280xp: correct Soundwire wakeup interrupt name

The bindings expect second Soundwire interrupt to be "wakeup" (Linux
driver takes by index):

  sc8280xp-crd.dtb: soundwire-controller@3330000: interrupt-names:1: 'wakeup' was expected

Fixes: c18773d162a6 ("arm64: dts: qcom: sc8280xp: add SoundWire and LPASS")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230403132328.61414-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845-tama: Enable GPI_DMA0/1

Enable both GPI DMAs.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-6-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Enable GPU

Enable the A630 GPU and its GMU.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-5-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Enable remoteprocs

Enable ADSP, CDSP and Venus.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-4-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Add regulator-system-load to l14a/l28a

Add the properties to ensure the ever so delicate touchscreen setup
matches downstream.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-3-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Add Synaptics Touchscreen

Add required pins and RMI4 node to the common DT and remove it
from Akatsuki, as it uses a different touch.

Since the panels are super high tech proprietary incell, they
need to be handled with very precise timings. As such the panel
driver sets up the power rails and GPIOs and the touchscreen
driver *has to* probe afterwards.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-2-2b1567c039d7@linaro.org

arm64: dts: qcom: sdm845-tama: Add display nodes

Add required nodes to support display on XZ2/XZ2c. XZ3 has a
different power rail setup and needs to be handled separately.

Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313-topic-tama_disp-v3-1-2b1567c039d7@linaro.org

arm64: dts: msm8953: Pad regs to 8 digits

Follow other dtses and pad regs to 8 digits.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-4-a39.skl@gmail.com

arm64: dts: msm8953: Drop unsupported dwc3 flag

Property phy_mode according to binding checker does not exist,
drop it.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-3-a39.skl@gmail.com

arm64: dts: msm8953: Provide dsi_phy clocks to gcc

Provide clocks from dsi_phy to gcc, this will make
sure we don't fallback to global name lookup.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-2-a39.skl@gmail.com

arm64: dts: msm8953: Replace xo_board with rpmcc sourced xo

Assign RPM_SMD_XO_CLK_SRC from rpmcc in place
of fixed-clock where possible.

Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230325112852.18841-1-a39.skl@gmail.com

arm64: dts: qcom: sm8450: remove invalid properties in cluster-sleep nodes

Fixes the following DT bindings check error:
domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'
domain-idle-states: cluster-sleep-1: 'idle-state-name', 'local-timer-stop' do not match any of the regexes:
'pinctrl-[0-9]+'

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230323-topic-sm8450-upstream-dt-bindings-fixes-v2-2-0ca1bea1a843@linaro.org

arm64: dts: qcom: sc8280xp: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name':

  sc8280xp-crd.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name' does not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8350: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm8350-mtp.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8150: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm8150-hdk.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm6375: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm6375-sony-xperia-murray-pdx225.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sdm845: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sdm845-shift-axolotl.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm8250: drop incorrect domain idle states properties

Domain idle states do not use 'idle-state-name' and 'local-timer-stop':

  sm8250-hdk.dtb: domain-idle-states: cluster-sleep-0: 'idle-state-name', 'local-timer-stop' do not match any of the regexes: 'pinctrl-[0-9]+'

Reported-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/all/20230323-topic-sm8450-upstream-dt-bindings-fixes-v1-4-3ead1e418fe4@linaro.org/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230324073813.22158-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sm6375-pdx225: Add volume down GPIO key

Add the required nodes to enable the volume down key on the Sony
Xperia 10 IV.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-14-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Introduce C3 power state for both ARM clusters

Introduce the C3 power state, which - to the best of my understanding -
gates the CPU clock, but does not shut off the power rail.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-13-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Bump CPU rail power collapse index

In preparation for supporting a less-deep sleep state, rename the
existing rail power off from _0 to _1.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-12-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Configure TSENS thermal zones

Add a thermal zones configuration for all 15+11 TSENS sensors.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-11-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add TSENS

Add nodes for the two TSENS v2.8.0 controllers present on the SoC.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-10-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add CPUCP L3 node

Configure the L3 cache DVFS scaler within the CPUCP block to allow
for dynamic frequency switching.

Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-9-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add modem nodes

Add required nodes to make the embedded 5G modem boot up on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-8-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add wifi node

Add a node for ATH10K_SNoC wifi on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-7-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add IMEM

Add a node for the IMEM block on SM6375.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-5-708b8191f7eb@linaro.org

arm64: dts: qcom: sm6375: Add RPM sleep stats

Add a node for RPM sleep stats to enable sleep monitoring.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230303-topic-sm6375_features0_dts-v2-4-708b8191f7eb@linaro.org

arm64: dts: qcom: sm8550: Use the correct BWMON fallback compatible

Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-7-77a050c2fbda@linaro.org

arm64: dts: qcom: sdm845: Use the correct BWMON compatible

Drop the incorrect msm8998 fallback and use the new qcom,sdm845-cpu-bwmon
compatible to distinguish the CPU BWMON found on this platform.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-6-77a050c2fbda@linaro.org

arm64: dts: qcom: sc8280xp: Use the correct BWMON fallback compatible

Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-5-77a050c2fbda@linaro.org

arm64: dts: qcom: sc7280: Use the correct BWMON fallback compatible

Use the correct fallback compatible for the BWMONv4 with merged global and
monitor register spaces.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230304-topic-ddr_bwmon-v3-4-77a050c2fbda@linaro.org

arm64: dts: qcom: sm6115: Add GPUCC and Adreno SMMU

Add GPUCC and Adreno SMMU nodes in preparation for adding the GPU
itself.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230315-topic-kamorta_adrsmmu-v1-2-d1c0dea90bd9@linaro.org

Merge branch '20230208091340.124641-1-konrad.dybcio@linaro.org' into HEAD

Introduce SM6115 GPUCC devicetree bindings, to make it possible to use
clock defines in the devicetree source.

arm64: dts: qcom: msm8998-yoshino: Use actual pin names for pin nodes

With the gpio-line-names in place coming from SONY themselves, we can
now make the pin nodes and their labels to more closely resemble the
actual thing. 4k has been renamed to four_k due to dtc limitations.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314-topic-yoshino_gpio-v2-2-4cb80e187e38@linaro.org

arm64: dts: qcom: msm8998-yoshino: Use SONY GPIO names

Sony ever so graciously provides GPIO line names in their downstream
kernel (though sometimes they are not 100% accurate and you can judge
that by simply looking at them and with what drivers they are used).

Add these to the Yoshino devices DTs to better document the hardware.

Lilac and Poplar have identical pin assignments.
Diff between these two and maple:

TLMM:
-  "NC",
+  "TS_VDDIO_EN",

PMI8998:
-  "NC"
+  "USB_SWITCH_SEL"

-  "NC"
+  "4K_DISP_DCDC_EN"

PM8005:
-  "NC"
+  "EAR_EN"

Which is probably due to Maple being designed and released quite a bit
earlier than the other two and it having a super high tech true-4K
display.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230314-topic-yoshino_gpio-v2-1-4cb80e187e38@linaro.org

arm64: dts: qcom: sdm845-xiaomi-beryllium: add notification LED

The Poco F1 has a single color white notification LED. Enable the
Qualcomm Light Pulse Generator (LPG) driver based notification LED.

Signed-off-by: Joel Selvaraj <joelselvaraj.oss@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313154226.136726-1-joelselvaraj.oss@gmail.com

arm64: dts: qcom: qdu1000: Add LLCC/system-cache-controller

Add a DT node for Last level cache (aka. system cache) controller
which provides control over the last level cache present on QDU1000
and QRU1000 SoCs.

Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230313125731.17745-1-quic_kbajaj@quicinc.com

arm64: dts: qcom: apq8096-db820c: drop unit address from PMI8994 regulator

The PMIC regulators are not supposed to have unit addresses.

Fixes: 2317b87a2a6f ("arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-8-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8994-msft-lumia-octagon: drop unit address from PMI8994 regulator

The PMIC regulators are not supposed to have unit addresses.

Fixes: 60b214effb80 ("arm64: dts: qcom: msm8994-octagon: Configure regulators")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-7-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8994-kitakami: drop unit address from PMI8994 regulator

The PMIC regulators are not supposed to have unit addresses.

Fixes: e9783584c9b7 ("arm64: dts: qcom: msm8994-kitakami: Add VDD_GFX regulator")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-6-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8998-oneplus-cheeseburger: revert "fix backlight pin function"

This reverts commit 46546f28825cf3a5ef6873b9cf947cd85c8a7258 because it
mistakenly took PMIC pinctrl/GPIO as TLMM.  The TLMM pinctrl uses "gpio"
function, but PMIC uses "normal", so original code was correct:

  msm8998-oneplus-cheeseburger.dtb: pmic@2: gpio@c000:button-backlight-state: 'oneOf' conditional failed, one must be fixed:
    'gpio' is not one of ['normal', 'paired', 'func1', 'func2', 'dtest1', 'dtest2', 'dtest3', 'dtest4', 'func3', 'func4']

Fixes: 46546f28825c ("arm64: dts: qcom: msm8998-oneplus-cheeseburger: fix backlight pin function")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-5-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-pazquel: correct trackpad supply

The hid-over-i2c takes VDD, not VCC supply.  Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:

  sc7180-trogdor-pazquel360-lte.dtb: trackpad@15: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: fb69f6adaf88 ("arm64: dts: qcom: sc7180: Add pazquel dts files")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-4-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7180-trogdor-lazor: correct trackpad supply

The hid-over-i2c takes VDD, not VCC supply.  Fix copy-pasta from other
boards which use elan,ekth3000 with valid VCC:

  sc7180-trogdor-lazor-limozeen-nots-r4.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: 2c26adb8dbab ("arm64: dts: qcom: Add sc7180-lazor-limozeen skus")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-3-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sc7280-herobrine-villager: correct trackpad supply

The hid-over-i2c takes VDD, not VCC supply.  Fix copy-pasta from other
Herobrine boards which use elan,ekth3000 with valid VCC:

  sc7280-herobrine-villager-r1-lte.dtb: trackpad@2c: 'vcc-supply' does not match any of the regexes: 'pinctrl-[0-9]+'

Fixes: ee2a62116015 ("arm64: dts: qcom: sc7280: Add device tree for herobrine villager")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-2-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: sda660-inforce: correct key node name

gpio-key bindings expect children to be named with generic prefix:

  sda660-inforce-ifc6560.dtb: gpio-keys: 'volup' does not match any of the regexes: ...

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230312183622.460488-1-krzysztof.kozlowski@linaro.org

arm64: dts: qcom: msm8916-yiming-uz801v3: Add initial device tree

This commit adds support for the uz801 v3.0 WiFi/LTE dongle made by
Henan Yiming Technology Co., Ltd. based on MSM8916.

Note: The original firmware does not support 64-bit OS. It is necessary
to flash 64-bit TZ firmware to boot arm64.

Currently supported:
- All CPU cores
- Buttons
- LEDs
- Modem
- SDHC
- USB Device Mode
- UART

Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/tencent_62395CA0D608DD0078DD3D889F6E4E22BA05@qq.com

arm64: dts: qcom: msm8916: Move WCN compatible to boards

On MSM8916 the wireless connectivity functionality (WiFi/Bluetooth) is
split into the digital part inside the SoC and the analog RF part inside
a supplementary WCN36xx chip. For MSM8916, three different options
exist:

  - WCN3620  (WLAN 802.11 b/g/n 2.4 GHz + Bluetooth)
  - WCN3660B (WLAN 802.11 a/b/g/n 2.4/5 GHz + Bluetooth)
  - WCN3680B (WLAN 802.11ac 2.4/5 GHz + Bluetooth)

Choosing one of these is up to the board vendor. This means that the
compatible belongs into the board-specific DT part so people porting
new boards pay attention to set the correct compatible.

Right now msm8916.dtsi sets "qcom,wcn3620" as default compatible,
which does not work at all for boards that have WCN3660B or WCN3680B.

Remove the default compatible from msm8196.dtsi and move it to the board
DT as follows:

  - Boards with only &pronto { status = "okay"; } used the default
    "qcom,wcn3620" so far. They now set this explicitly for &wcnss_iris.
  - Boards with &pronto { ... iris { compatible = "qcom,wcn3660b"; }};
    already had an override that just moves to &wcnss_iris now.
  - For msm8916-samsung-a2015-common.dtsi the WCN compatible differs for
    boards making use of it (a3u: wcn3620, a5u: wcn3660b, e2015: wcn3620)
    so the definitions move to the board-specific DT part.

Since this requires touching all the board DTs, use this as a chance to
name the WCNSS-related labels consistently, so everything is grouped
properly when sorted alphabetically.

No functional change, just clean-up for more clarity & easier porting.
Aside from ordering the generated DTBs are identical.

Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
Link: https://lore.kernel.org/r/20230309091452.1011776-1-stephan.gerhold@kernkonzept.com

pinctrl: qcom: Support OUTPUT_ENABLE; deprecate INPUT_ENABLE

The Qualcomm pinctrl driver has been violating the documented meaning
of PIN_CONFIG_INPUT_ENABLE. That documentation says:

  Note that this does not affect the pin's ability to drive output.

...yet the Qualcomm driver's sole action when asked to "enable input"
on a pin is to disable its output.

The Qualcomm driver's implementation stems from the fact that
"output-disable" is a "new" property from 2017. It was introduced in
commit 425562429d4f ("pinctrl: generic: Add output-enable
property"). The "input-enable" handling in Qualcomm drivers is from
2015 introduced in commit 407f5e392f9c ("pinctrl: qcom: handle
input-enable pinconf property").

Let's change the Qualcomm driver to move us in the right direction. As
part of this:
1. We'll now support PIN_CONFIG_OUTPUT_ENABLE
2. We'll still support using PIN_CONFIG_INPUT_ENABLE to disable a
   pin's output (in violation of the docs) with a big comment in the
   code. This is needed because old device trees have "input-enable"
   in them and, in some cases, people might need the old
   behavior. While we could programmatically change all old device
   trees, it doesn't really hurt to keep supporting the old behavior
   and we're _supposed_ to try to be compatible with old device trees
   anyway.

It can also be noted that the PIN_CONFIG_INPUT_ENABLE handling code
seems to have purposefully ignored its argument. That means that old
boards that had _either_ "input-disable" or "input-enable" in them
would have had the effect of disabling a pin's output. While we could
change this behavior, since we're only leaving the
PIN_CONFIG_INPUT_ENABLE there for backward compatibility we might as
well be fully backward compatible.

NOTE: despite the fact that we'll still support
PIN_CONFIG_INPUT_ENABLE for _setting_ config, we take it away from
msm_config_group_get(). This appears to be only used for populating
debugfs and fixing debugfs to "output enabled" where relevant instead
of "input enabled" makes more sense and has more truthiness.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Bjorn Andersson <andersson@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230323102605.8.Id740ae6a993f9313b58add6b10f6a92795d510d4@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: qcom: Add output-enable

In the patch ("dt-bindings: pinctrl: qcom: tlmm should use
output-disable, not input-enable") we allowed setting "output-disable"
for TLMM pinctrl states. Let's also add "output-enable".

At first blush this seems a needless thing to do. Specifically:
- In Linux (and presumably any other OSes using the same device trees)
  the GPIO/pinctrl driver knows to automatically enable the output
  when a GPIO is changed to an output. Thus in most cases specifying
  "output-enable" is superfluous and should be avoided.
- If we need to set a pin's default state we already have
  "output-high" and "output-low" and these properties already imply
  "output-enabled" (at least on the Linux Qualcomm TLMM driver).

However, there is one instance where "output-enable" seems like it
could be useful: sleep states. It's not uncommon to want to configure
pins as inputs (with appropriate pulls) when the driver controlling
them is in a low power state. Then we want the pins back to outputs
when the driver wants things running normally. To accomplish this we'd
want to be able to use "output-enable". Then the "default" state could
have "output-enable" and the "sleep" state could have
"output-disable".

NOTE: in all instances I'm aware of, we'd only want to use
"output-enable" on pins that are configured as "gpio". The Qualcomm
documentation that I have access to says that "output-enable" only
does something useful when in GPIO mode.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230323102605.7.I7874c00092115c45377c2a06f7f133356956686e@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

dt-bindings: pinctrl: qcom: tlmm should use output-disable, not input-enable

As evidenced by the Qualcomm TLMM Linux driver, the TLMM IP block in
Qualcomm SoCs has a bit to enable/disable the output for a pin that's
configured as a GPIO but _not_ a bit to enable/disable an input
buffer. Current device trees that are specifying "input-enable" for
pins managed by TLMM are either doing so needlessly or are using it to
mean "output-disable".

Presumably the current convention of using "input-enable" to mean
"output-disable" stems from the fact that "output-disable" is a "new"
property from 2017. It was introduced in commit 425562429d4f
("pinctrl: generic: Add output-enable property"). The "input-enable"
handling in Qualcomm drivers is from 2015 introduced in commit
407f5e392f9c ("pinctrl: qcom: handle input-enable pinconf property").

Given that there's no other use for "input-enable" for TLMM, we can
still handle old device trees in code, but let's encourage people to
move to the proper / documented property by updating the bindings.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20230323102605.6.I291ce0ba2c6ea80b341659c4f75a567a76dd7ca6@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge branch 'arm64-fixes-for-6.3' into arm64-for-6.4

Merge the arm64-fixes-for-6.3 branch to avoid merge conflicts with
changes for v6.4.