Siddh Raman Pant [Thu, 12 May 2022 14:36:45 +0000 (20:06 +0530)]
spi: Doc fix - Describe add_lock and dma_map_dev in spi_controller
This fixes the corresponding warnings during building the docs.
Signed-off-by: Siddh Raman Pant <siddhpant.gh@gmail.com>
Link: https://lore.kernel.org/r/4e6187a4-d0f8-4750-e407-e09cc1c91789@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vaishnav Achath [Wed, 11 May 2022 11:55:16 +0000 (17:25 +0530)]
spi: cadence-quadspi: Handle spi_unregister_master() in remove()
Currently devres managed removal of the spi_controller happens after
removing the power domain of the host platform_device.While this
does not affect the clean removal of the controller, but affects
graceful removal of the child devices if the child device removal
requires issuing commands over SPI.
Eg. flash device being soft reset to 1S-1S-1S mode before removal
so that on next probe operations in 1S-1S-1S mode is successful.
Failure is seen when `rmmod spi-cadence-quadspi` is performed:
root@j7-evm:~# rmmod spi_cadence_quadspi
[ 49.230996] cadence-qspi
47050000.spi: QSPI is still busy after 500ms timeout.
[ 49.238209] spi-nor spi1.0: operation failed with -110
[ 49.244457] spi-nor spi1.0: Software reset failed: -110
and on subsequent modprobe the OSPI flash probe fails as it
is in 8D-8D-8D mode since the previous soft reset did not happen.
root@j7-evm:~# modprobe spi_cadence_quadspi
[ 73.253536] spi-nor spi0.0: unrecognized JEDEC id bytes: ff ff ff ff ff ff
[ 73.260476] spi-nor: probe of spi0.0 failed with error -2
This commit adds necessary changes to perform spi_unregister_master()
in the host device remove() so that the child devices are gracefully
removed before the power domain is removed.
changes tested on J721E with mt35xu512aba flash.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20220511115516.14894-1-vaishnav.a@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 11 May 2022 18:48:07 +0000 (19:48 +0100)]
spi: stm32-qspi: flags management fixes
Merge series from patrice.chotard@foss.st.com <patrice.chotard@foss.st.com>
Patrice Chotard <patrice.chotard@foss.st.com>:
From: Patrice Chotard <patrice.chotard@foss.st.com>
This series update flags management in the following cases:
- In APM mode, don't take care of TCF and TEF flags
- Always check TCF flag in stm32_qspi_wait_cmd()
- Don't check BUSY flag when sending new command
Patrice Chotard [Wed, 11 May 2022 07:46:44 +0000 (09:46 +0200)]
spi: stm32-qspi: Remove SR_BUSY bit check before sending command
Waiting for SR_BUSY bit when receiving a new command is not needed.
SR_BUSY bit is already managed in the previous command treatment.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220511074644.558874-4-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard [Wed, 11 May 2022 07:46:43 +0000 (09:46 +0200)]
spi: stm32-qspi: Always check SR_TCF flags in stm32_qspi_wait_cmd()
Currently, SR_TCF flag is checked in case there is data, this criteria
is not correct.
SR_TCF flags is set when programmed number of bytes has been transferred
to the memory device ("bytes" comprised command and data send to the
SPI device).
So even if there is no data, we must check SR_TCF flag.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220511074644.558874-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Patrice Chotard [Wed, 11 May 2022 07:46:42 +0000 (09:46 +0200)]
spi: stm32-qspi: Fix wait_cmd timeout in APM mode
In APM mode, TCF and TEF flags are not set. To avoid timeout in
stm32_qspi_wait_cmd(), don't check if TCF/TEF are set.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reported-by: eberhard.stoll@kontron.de
Link: https://lore.kernel.org/r/20220511074644.558874-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Ian Abbott [Tue, 10 May 2022 11:51:41 +0000 (12:51 +0100)]
spi: cadence-quadspi: remove unnecessary (void *) casts
Remove a couple of unnecessary casts to `(void *)` when initializing the
`.data` members in the device ID table.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220510115141.212779-3-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Ian Abbott [Tue, 10 May 2022 11:51:40 +0000 (12:51 +0100)]
spi: cadence-quadspi: Add missing blank line in cqspi_request_mmap_dma()
Fix "WARNING: Missing a blank line after declarations" reported by
checkpatch.pl.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220510115141.212779-2-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:57 +0000 (19:54 +0200)]
spi: spi-imx: mx51_ecspi_prepare_message(): skip writing MX51_ECSPI_CONFIG register if unchanged
In mx51_ecspi_prepare_message() the MX51_ECSPI_CONFIG register is
setup for the current spi_message. After writing the register, there
is a delay to ensure that the changes hit the hardware.
This patch checks if the register MX51_ECSPI_CONFIG actually needs to
be changed. If the register content is unchanged the function is left
early, skipping the write to the hardware and the delay. This leads to
a small, but measurable performance increase. For a given workload
with small transfers on an imx6 single core the CPU load decreases
from 30% to ~27%.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-10-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:56 +0000 (19:54 +0200)]
spi: spi-imx: add PIO polling support
The driver supports several modes, one of them is PIO/IRQ
"spi_imx_pio_transfer()". The data is exchanged with the IP core using
PIO, an IRQ is setup to signal empty/full FIFOs and the end of the
transfer. The IRQ and scheduling overhead for short transfers is
significant. Using polling instead of IRQs can be beneficial to reduce
the overall CPU load, especially on small transfer workloads.
On an imx6 single core, a given RX workload of the mcp251xfd driver
results in 40% CPU load. Using polling mode reduces the CPU load to
30%.
This patch adds PIO polling support to the driver. For transfers with
a duration of less than 30 µs the polling mode instead of IRQ based
PIO mode is used. 30 µs seems to be a good compromise, which is used
the by the SPI drivers for the raspberry Pi (spi-bcm2835,
spi-bcm2835), too.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-9-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:55 +0000 (19:54 +0200)]
spi: spi-imx: replace struct spi_imx_data::bitbang by pointer to struct spi_controller
There's no need to embed the struct spi_bitbang into our private
data (struct spi_imx_data), the spi core is flexible enough, so that
we only need a pointer to the allocated struct spi_controller.
This is also a preparation patch to add PIO based polling support to
the driver.
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-8-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:54 +0000 (19:54 +0200)]
spi: spi-imx: complete conversion from master -> controller
With patch:
|
8caab75fd2c2 ("spi: Generalize SPI "master" to "controller"")
the SPI "master" was generalized to "controller". This patch completed
the conversion of the spi-imx driver by replacing the remaining
occurrences of master to controller.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-7-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:53 +0000 (19:54 +0200)]
spi: spi-imx: spi_imx_buf_rx_swap_u32(): replace open coded swahw32s()
This patch replaces an open coded swahw32s().
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-6-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:52 +0000 (19:54 +0200)]
spi: spi-imx: spi_imx_buf_rx_swap_u32(): fix sparse warning: use swab32s() instead of cpu_to_be32()
This patch fixes the following sparse warning by using a swab32s()
instead of a cpu_to_be32(). The driver is used on little endian
systems only and we really want to swap the bytes.
| drivers/spi/spi-imx.c:305:29: warning: incorrect type in assignment (different base types)
| drivers/spi/spi-imx.c:305:29: expected unsigned int val
| drivers/spi/spi-imx.c:305:29: got restricted __be32 [usertype]
| drivers/spi/spi-imx.c:361:21: warning: incorrect type in assignment (different base types)
| drivers/spi/spi-imx.c:361:21: expected unsigned int [assigned] [usertype] val
| drivers/spi/spi-imx.c:361:21: got restricted __be32 [usertype]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-5-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:51 +0000 (19:54 +0200)]
spi: spi-imx: mx51_ecspi_intctrl(): prefer 'unsigned int' to bare use of 'unsigned'
This patch fixes the following checkpatch warning, by making val an
"unsigned int".
| WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
| + unsigned val = 0;
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-4-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:50 +0000 (19:54 +0200)]
spi: spi-imx: avoid unnecessary line continuations
This patch fixes the following checkpatch warning by removing the
trailing backslash:
| WARNING: Avoid unnecessary line continuations
| + spi_imx->bitbang.master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-3-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Marc Kleine-Budde [Mon, 2 May 2022 17:54:49 +0000 (19:54 +0200)]
spi: spi-imx: fix sparse warning: add identifier name to function definition
This patch fixes the following and similar sparse warnings by adding
the missing identifier names to the function definitions:
| WARNING: function definition argument 'struct spi_imx_data *' should also have an identifier name
| #68: FILE: drivers/spi/spi-imx.c:68:
| + int (*prepare_message)(struct spi_imx_data *, struct spi_message *);
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/r/20220502175457.1977983-2-mkl@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Yang Yingliang [Thu, 5 May 2022 09:39:54 +0000 (17:39 +0800)]
spi: spi-fsl-qspi: check return value after calling platform_get_resource_byname()
It will cause null-ptr-deref if platform_get_resource_byname() returns NULL,
we need check the return value.
Fixes:
858e26a515c2 ("spi: spi-fsl-qspi: Reduce devm_ioremap size to 4 times AHB buffer size")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20220505093954.1285615-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andrea Zanotti [Mon, 2 May 2022 11:13:00 +0000 (13:13 +0200)]
spi: omap2-mcspi: add support for interword delay
The module omap2-mcspi does not support the interword delay
parameter present in the spi transfer. On one side, if the module
is instructed to use the dma, this parameter is correctly ignored.
However, without the usage of the dma, that parameter should be
used.
The patch introduce the handling of such delay in the omap2-mcspi
module, using standard spi_delay struct. The patch has been tested
using as benchmark a DM3730.
The delay function used (spi_delay_exec) is already present in the
kernel and it checks on its own the validity of the input, as such,
no additional checks are present.
The range of usage of the udelay function is incremented to 200 us,
as the change from udelay to usleep_range introduces not
neglectible delays.
Signed-off-by: Andrea Zanotti <andreazanottifo@gmail.com>
Link: https://lore.kernel.org/r/20220502111300.24754-1-andreazanottifo@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Biju Das [Sun, 1 May 2022 08:21:50 +0000 (09:21 +0100)]
spi: dt-bindings: renesas,rspi: Document RZ/G2UL SoC
Add RSPI binding documentation for Renesas RZ/G2UL SoC.
RSPI block is identical to one found on RZ/A, so no driver changes are
required. The fallback compatible string "renesas,rspi-rz" will be used
on RZ/G2UL.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220501082150.24662-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Dan Carpenter [Fri, 29 Apr 2022 17:41:37 +0000 (20:41 +0300)]
spi: mtk-snfi: preserve dma_mapping_error() error codes
Return -ENOMEM of there is a dma mapping error. Do not return success.
Fixes:
764f1b748164 ("spi: add driver for MTK SPI NAND Flash Interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chuanhong Guo <gch981213@gmail.com>
Link: https://lore.kernel.org/r/YmwjUcTKyQNrrn2g@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
Ian Abbott [Wed, 27 Apr 2022 15:34:46 +0000 (16:34 +0100)]
spi: cadence-quadspi: fix Direct Access Mode disable for SoCFPGA
The Cadence QSPI compatible string required for the SoCFPGA platform
changed from the default "cdns,qspi-nor" to "intel,socfpga-qspi" with
the introduction of an additional quirk in
commit
98d948eb8331 ("spi: cadence-quadspi: fix write completion support").
However, that change did not preserve the previously used
quirk for this platform. Reinstate the `CQSPI_DISABLE_DAC_MODE` quirk
for the SoCFPGA platform.
Fixes:
98d948eb8331 ("spi: cadence-quadspi: fix write completion support")
Cc: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20220427153446.10113-1-abbotti@mev.co.uk
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuanhong Guo [Sun, 24 Apr 2022 03:25:26 +0000 (11:25 +0800)]
spi: dt-bindings: add binding doc for spi-mtk-snfi
Add device-tree binding documentation for Mediatek SPI-NAND Flash
Interface.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220424032527.673605-5-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Chuanhong Guo [Sun, 24 Apr 2022 03:25:24 +0000 (11:25 +0800)]
spi: add driver for MTK SPI NAND Flash Interface
This driver implements support for the SPI-NAND mode of MTK NAND Flash
Interface as a SPI-MEM controller with pipelined ECC capability.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Link: https://lore.kernel.org/r/20220424032527.673605-3-gch981213@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 27 Apr 2022 16:22:02 +0000 (17:22 +0100)]
spi: Pull Mediatek ECC changes
Mediatek ECC changes:
* Also parse the default nand-ecc-engine property if available
* Make mtk_ecc.c a separated module
needed for SPI controller driver
Chuanhong Guo [Sun, 24 Apr 2022 03:25:25 +0000 (11:25 +0800)]
mtd: nand: mtk-ecc: also parse nand-ecc-engine if available
The recently added ECC engine support introduced a generic property
named nand-ecc-engine for ecc engine phandle. This patch adds support
for this new property.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-4-gch981213@gmail.com
Chuanhong Guo [Sun, 24 Apr 2022 03:25:23 +0000 (11:25 +0800)]
mtd: nand: make mtk_ecc.c a separated module
this code will be used in mediatek snfi spi-mem controller with
pipelined ECC engine.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20220424032527.673605-2-gch981213@gmail.com
Mark Brown [Mon, 25 Apr 2022 17:22:58 +0000 (18:22 +0100)]
Improve SPI support for Ingenic SoCs.
Merge series from 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>:
1.Add support for using GPIOs as chip select lines on Ingenic SoCs.
2.Add support for probing the spi-ingenic driver on the JZ4775 SoC,
the X1000 SoC, and the X2000 SoC.
3.Modify annotation texts to be more in line with the current state.
Alexander Shiyan [Wed, 20 Apr 2022 06:10:38 +0000 (09:10 +0300)]
spi: clps711x: Use syscon_regmap_lookup_by_phandle
Since version 5.13, the standard syscon bindings have been added
to all clps711x DT nodes, so we can now use the more general
syscon_regmap_lookup_by_phandle function to get the syscon pointer.
Signed-off-by: Alexander Shiyan <eagle.alexander923@gmail.com>
Link: https://lore.kernel.org/r/20220420061038.22570-1-eagle.alexander923@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Wed, 20 Apr 2022 09:04:52 +0000 (09:04 +0000)]
spi: stm32: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220420090452.2588930-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Thu, 14 Apr 2022 08:56:37 +0000 (08:56 +0000)]
spi: spi-cadence-quadspi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085637.2541805-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Mon, 18 Apr 2022 11:01:41 +0000 (11:01 +0000)]
spi: spi-tegra20-slink: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418110141.2559019-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Matthias Schiffer [Wed, 20 Apr 2022 15:56:16 +0000 (17:56 +0200)]
spi: cadence-quadspi: allow operations with cmd/addr buswidth >1
With the removal of the incorrect logic of cqspi_set_protocol(), ops with
cmd/addr buswidth >1 are now working correctly.
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash using 1-4-4
operations.
DTR operations are currently untested, so we leave them disabled for now
(except for the previously allowed 8-8-8 ops).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220420155616.281730-2-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Matthias Schiffer [Wed, 20 Apr 2022 15:56:15 +0000 (17:56 +0200)]
spi: cadence-quadspi: drop cqspi_set_protocol()
As suggested, this removes the whole cqspi_set_protocol() function, as it
is not actually needed:
- Checks for unsupported operations are already handled by supports_op(),
removing the need to distinguish DTR and non-DTR modes in the buswidth
setup
- supports_op() ensures that the DTR flags match for all relevant parts of
an operation, so op->cmd.dtr can be used instead of copying the flag to
the cqspi_flash_pdata
- The logic in cqspi_set_protocol() is moved to cqspi_calc_rdreg() and
cqspi_write_setup() (with a helper macro CQSPI_OP_WIDTH())
The helper macro checks nbytes instead of buswidth for 0, for consistency
with supports_op() etc.
Suggested-by: Pratyush Yadav <p.yadav@ti.com>
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220420155616.281730-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Mon, 18 Apr 2022 11:01:03 +0000 (11:01 +0000)]
spi: spi-tegra20-sflash: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418110103.2558955-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Luca Ceresoli [Thu, 21 Apr 2022 21:32:51 +0000 (23:32 +0200)]
spi: rockchip: fix missing error on unsupported SPI_CS_HIGH
The hardware (except for the ROCKCHIP_SPI_VER2_TYPE2 version) does not
support active-high native chip selects. However if such a CS is configured
the core does not error as it normally should, because the
'ctlr->use_gpio_descriptors = true' line in rockchip_spi_probe() makes the
core set SPI_CS_HIGH in ctlr->mode_bits.
In such a case the spi-rockchip driver operates normally but produces an
active-low chip select signal without notice.
There is no provision in the current core code to handle this
situation. Fix by adding a check in the ctlr->setup function (similarly to
what spi-atmel.c does).
This cannot be done reading the SPI_CS_HIGH but in ctlr->mode_bits because
that bit gets always set by the core for master mode (see above).
Fixes:
eb1262e3cc8b ("spi: spi-rockchip: use num-cs property and ctlr->enable_gpiods")
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Link: https://lore.kernel.org/r/20220421213251.1077899-1-luca.ceresoli@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Thu, 14 Apr 2022 08:54:33 +0000 (08:54 +0000)]
spi: spi-omap2-mcspi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085433.2541670-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Wed, 20 Apr 2022 09:04:20 +0000 (09:04 +0000)]
spi: mxs: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220420090420.2588868-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Thu, 14 Apr 2022 08:53:42 +0000 (08:53 +0000)]
spi: spi-imx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085343.2541608-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Thu, 14 Apr 2022 08:55:06 +0000 (08:55 +0000)]
spi: spi-sprd: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220414085506.2541732-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
周琰杰 (Zhou Yanjie) [Sat, 23 Apr 2022 14:38:45 +0000 (22:38 +0800)]
spi: ingenic: Add support for new Ingenic SoCs.
1.Since it would be dangerous to specify a newer SoC's compatible
string as the fallback of an older SoC's compatible string, we
add support for the "ingenic,jz4775-spi" compatible string in
the driver.
This will permit to support the JZ4775 by having:
compatible = "ingenic,jz4775-spi";
Instead of doing:
compatible = "ingenic,jz4775-spi", "ingenic,jz4780-spi";
2.Add support for probing the spi-ingenic driver on the X1000 SoC
from Ingenic. From the X1000 SoC onwards, the maximum frequency
allowed by the SSI module of Ingenic SoCs has been changed from
54MHz to 50MHz. So "max_speed_hz" is introduced in "jz_soc_info"
to set different maximum frequency values.
3.Add support for probing the spi-ingenic driver on the X2000 SoC
from Ingenic. The X2000 SoC has only one native chip select line,
so "max_native_cs" is introduced in "jz_soc_info" to set different
maximum number of native chip select lines.
4.Because of the introduction of support for the X-series SoCs, the
current driver is not only applicable to the JZ-series SoCs, so
the description texts has been modified to avoid misunderstanding.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1650724725-93758-4-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
周琰杰 (Zhou Yanjie) [Sat, 23 Apr 2022 14:38:44 +0000 (22:38 +0800)]
spi: Add bindings for new Ingenic SoCs.
Add the SPI bindings for the JZ4775 SoC, the X1000 SoC,
and the X2000 SoC from Ingenic.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1650724725-93758-3-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
周琰杰 (Zhou Yanjie) [Sat, 23 Apr 2022 14:38:43 +0000 (22:38 +0800)]
spi: ingenic: Add support for use GPIO as chip select line.
Add support for using GPIOs as chip select lines on Ingenic SoCs.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/1650724725-93758-2-git-send-email-zhouyanjie@wanyeetech.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Zheng Yongjun [Fri, 22 Apr 2022 06:26:41 +0000 (06:26 +0000)]
spi: img-spfi: Fix pm_runtime_get_sync() error checking
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes:
deba25800a12b ("spi: Add driver for IMG SPFI controller")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062641.10486-1-zhengyongjun3@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pratyush Yadav [Wed, 20 Apr 2022 10:20:22 +0000 (15:50 +0530)]
spi: spi-mem: check if data buffers are on stack
The buffers passed in the data phase must be DMA-able. Programmers often
don't realise this requirement and pass in buffers that reside on the
stack. This can be hard to spot when reviewing code. Reject ops if their
data buffer is on the stack to avoid this.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220420102022.3310970-1-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mika Westerberg [Wed, 20 Apr 2022 10:43:50 +0000 (13:43 +0300)]
spi: intel: Implement dirmap hooks
Currently the driver goes over the supported opcodes list each time
->exec_op() is called and finds the suitable for the given operation.
This consumes unnecessary amount of CPU cycles because the operation is
always the same. For this reason populate dirmap hooks for the driver so
that we cache the selected operation and then simply call it on each
read/write.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220420104350.19510-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 20 Apr 2022 13:22:11 +0000 (14:22 +0100)]
MediaTek SPI controller cleanups and documentation
Merge series from AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>:
This series performs some cleanups to the spi-mt65xx driver, removing
all gotos, simplifying the probe function and adding kerneldoc to the
driver structures.
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:28 +0000 (13:44 +0200)]
spi: mt65xx: Fix definitions indentation
Some definitions at the beginning of this file were wrongly
indented: fix the indentation for all of these and, while at
it, also move the MTK_SPI_IDLE and MTK_SPI_PAUSED down, as to
implicitly group the hardware related definitions to the
software (driver) related ones.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-9-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:27 +0000 (13:44 +0200)]
spi: mt65xx: Add kerneldoc for driver structures
One of the two structures was already partially documented, but not
in kerneldoc format: enhance readability by adding the missing
documentation bits and use kerneldoc.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-8-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:26 +0000 (13:44 +0200)]
spi: mt65xx: Simplify probe function with dev_err_probe()
Switch to dev_err_probe() to remove all dev_err() -> return repeated
patterns, simplifying and shortening the probe function.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-7-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:25 +0000 (13:44 +0200)]
spi: mt65xx: Move pm_runtime_enable() call to remove all gotos
The last goto in the probe function can be removed by calling
pm_runtime_enable() right before devm_spi_register_master(), as
only some init checks were being performed after enabling pm.
This is a cleanup and brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:24 +0000 (13:44 +0200)]
spi: mt65xx: Move clock parent setting to remove clock disable gotos
Reparenting sel_clk to parent_clk can be done before enabling any of
spi_clk and spi_hclk. Move the call to clk_set_parent() for sel_clk
earlier, and call disable_unprepare() upon spi_clk prepare_enable()
failure to remove all clock disablement related gotos.
This commit is in preparation of a later cleanup.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:23 +0000 (13:44 +0200)]
spi: mt65xx: Add and use pointer to struct device in mtk_spi_probe()
In preparation for switching to dev_err_probe() in this function, add
a pointer to struct device and replace all occurrences of '&pdev->dev'
to using this 'dev' pointer.
This is done for one-line fitting of the dev_err_probe() calls.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:22 +0000 (13:44 +0200)]
spi: mt65xx: Switch to device_get_match_data()
Instead of performing yet another match check in the probe function,
simply switch to device_get_match_data().
This is a cleanup and brings no functional change.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
AngeloGioacchino Del Regno [Thu, 7 Apr 2022 11:44:21 +0000 (13:44 +0200)]
spi: mt65xx: Simplify probe function with devm_spi_alloc_master
Switch to the devm variant of spi_alloc_master() to save some gotos.
This patch is a cleanup that brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220407114428.167091-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Mon, 18 Apr 2022 11:02:26 +0000 (11:02 +0000)]
spi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220418110226.2559081-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Baruch Siach [Mon, 11 Apr 2022 18:45:29 +0000 (21:45 +0300)]
spi: spi-imx: add support for SPI_RX_CPHA_FLIP
When SPI_RX_CPHA_FLIP is set, flip CPHA on Rx only transfers. This is
useful to access devices that use inverted CPHA for MISO vs MOSI
signals.
Only support the mx51/mx53 variants for now.
Tested on i.MX6ULL based system.
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Link: https://lore.kernel.org/r/e11b4446afe9a46a282dd923d22c27d03fae15f8.1649702729.git.baruch@tkos.co.il
Signed-off-by: Mark Brown <broonie@kernel.org>
Baruch Siach [Mon, 11 Apr 2022 18:45:28 +0000 (21:45 +0300)]
spi: spidev: add SPI_RX_CPHA_FLIP
Allow userspace to set SPI_RX_CPHA_FLIP mode bit using the
SPI_IOC_WR_MODE32 ioctl.
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Link: https://lore.kernel.org/r/6ae31ad24f8252418878b21a8759a04b78726dac.1649702729.git.baruch@tkos.co.il
Signed-off-by: Mark Brown <broonie@kernel.org>
Baruch Siach [Mon, 11 Apr 2022 18:45:27 +0000 (21:45 +0300)]
spi: add SPI_RX_CPHA_FLIP mode bit
Some SPI devices latch MOSI bits on one clock phase, but produce valid
MISO bits on the other phase. Add SPI_RX_CPHA_FLIP mode to instruct the
controller driver to flip CPHA for Rx (MISO) only transfers.
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Link: https://lore.kernel.org/r/a715ca92713ca02071f33dcca9960a66a03c949a.1649702729.git.baruch@tkos.co.il
Signed-off-by: Mark Brown <broonie@kernel.org>
Mika Westerberg [Mon, 11 Apr 2022 11:31:57 +0000 (14:31 +0300)]
spi: intel: Fix typo in kernel-doc of intel_spi_probe()
Should be 'specific' not 'spefific'. Fix this.
Reported-by: Hongli Li <hongli.li@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220411113158.2037-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Fri, 8 Apr 2022 08:09:31 +0000 (08:09 +0000)]
spi: spi-ti-qspi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220408080931.2494356-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Tue, 12 Apr 2022 07:09:51 +0000 (07:09 +0000)]
spi: spi-tegra114: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220412070951.2532157-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Wed, 13 Apr 2022 09:36:56 +0000 (09:36 +0000)]
spi: spi-cadence-quadspi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Link: https://lore.kernel.org/r/20220413093656.2538504-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Li-hao Kuo [Fri, 15 Apr 2022 08:12:04 +0000 (16:12 +0800)]
spi: remove spin_lock_irq and variable in the irq procress
remove spin_lock_irq spin_unlock_irq and variable in the irq funciton
Signed-off-by: Li-hao Kuo <lhjeff911@gmail.com>
Link: https://lore.kernel.org/r/f9991d6064d892d22ac7c2dfabe16309e9d03888.1650010304.git.lhjeff911@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Paul Kocialkowski [Thu, 14 Apr 2022 08:40:40 +0000 (10:40 +0200)]
spi: core: Initialize returned status in spi_setup
The previous commit that made bits-per-word validation conditional
results in leaving no unconditional affectation of the status variable.
Since the variable is returned at the end of the function, initialize
it to avoid returning an undefined value.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Fixes:
b3fe2e516741 ("spi: core: Only check bits_per_word validity when explicitly provided")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20220414084040.975520-1-paul.kocialkowski@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Wed, 13 Apr 2022 17:33:28 +0000 (18:33 +0100)]
spi: Pull in Atmel fix
Pull in Atmel fix series, only first patch of which is for Linus
Signed-off-by: Mark Brown <broonie@kernel.org>
Tudor Ambarus [Wed, 6 Apr 2022 13:36:04 +0000 (16:36 +0300)]
spi: atmel-quadspi: Remove duplicated DTR checks
Remove the DTR checks as they are already handled in
spi_mem_default_supports_op(). This code removal was intentionally not done
in the previous patch that introduced the use of the
spi_mem_default_supports_op() core helper and fixed the buswidth adjustment
between SPIMEM and the SPI controller, so that the fix can be easily
backported to stable kernels.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220406133604.455356-2-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Tudor Ambarus [Wed, 6 Apr 2022 13:36:03 +0000 (16:36 +0300)]
spi: atmel-quadspi: Fix the buswidth adjustment between spi-mem and controller
Use the spi_mem_default_supports_op() core helper in order to take into
account the buswidth specified by the user in device tree.
Cc: <stable@vger.kernel.org>
Fixes:
0e6aae08e9ae ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20220406133604.455356-1-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Matthias Schiffer [Wed, 6 Apr 2022 13:28:32 +0000 (15:28 +0200)]
spi: cadence-quadspi: fix incorrect supports_op() return value
Since the conversion to spi-mem, the driver advertised support for
various operations that cqspi_set_protocol() was never expected to handle
correctly - in particuar all non-DTR operations with command or address
buswidth > 1. For DTR, all operations except for 8-8-8 would fail, as
cqspi_set_protocol() returns -EINVAL.
In non-DTR mode, this resulted in data corruption for SPI-NOR flashes that
support such operations. As a minimal fix that can be backported to stable
kernels, simply disallow the unsupported operations again to avoid this
issue.
Fixes:
a314f6367787 ("mtd: spi-nor: Convert cadence-quadspi to use spi-mem framework")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220406132832.199777-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Mika Westerberg [Mon, 11 Apr 2022 11:21:16 +0000 (14:21 +0300)]
spi: intel: Add support for Raptor Lake-S SPI serial flash
Intel Raptor Lake-S has the same SPI serial flash controller as Alder
Lake-P. Add Raptor Lake-S PCI ID to the driver list of supported
devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20220411112116.53281-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Allen-KH Cheng [Tue, 12 Apr 2022 11:57:43 +0000 (19:57 +0800)]
spi: spi-mtk-nor: initialize spi controller after resume
After system resumes, the registers of nor controller are
initialized with default values. The nor controller will
not function properly.
To handle both issues above, we add mtk_nor_init() in
mtk_nor_resume after pm_runtime_force_resume().
Fixes:
3bfd9103c7af ("spi: spi-mtk-nor: Add power management support")
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220412115743.22641-1-allen-kh.cheng@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Biju Das [Mon, 11 Apr 2022 17:31:15 +0000 (18:31 +0100)]
spi: spi-rspi: Remove setting {src,dst}_{addr,addr_width} based on DMA direction
The direction field in the DMA config is deprecated. The rspi driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
This patch fixes the issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220411173115.6619-1-biju.das.jz@bp.renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Paul Kocialkowski [Tue, 12 Apr 2022 12:22:07 +0000 (14:22 +0200)]
spi: core: Only check bits_per_word validity when explicitly provided
On SPI device probe, the core will call spi_setup in spi_add_device
before the corresponding driver was probed. When this happens, the
bits_per_word member of the device is not yet set by the driver,
resulting in the default being set to 8 bits-per-word.
However some controllers do not support 8 bits-per-word at all, which
results in a failure when checking the bits-per-word validity.
In order to support these devices, skip the bits-per-word validity
check when it is not explicitly provided by drivers.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://lore.kernel.org/r/20220412122207.130181-1-paul.kocialkowski@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Minghao Chi [Tue, 12 Apr 2022 07:09:06 +0000 (07:09 +0000)]
spi: spi-stm32-qspi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20220412070906.2532091-1-chi.minghao@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Miaoqian Lin [Mon, 11 Apr 2022 11:10:33 +0000 (11:10 +0000)]
spi: spi-ti-qspi: Fix return value handling of wait_for_completion_timeout
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes:
5720ec0a6d26 ("spi: spi-ti-qspi: Add DMA support for QSPI mmap read")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220411111034.24447-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Michal Simek [Tue, 22 Mar 2022 15:00:18 +0000 (20:30 +0530)]
spi: spi-cadence: Fix kernel-doc format for resume/suspend
Kernel function name don't match with function name.
Error log:
drivers/spi/spi-cadence.c:661: warning: expecting prototype for
cdns_spi_runtime_resume(). Prototype was for cnds_runtime_resume() instead
drivers/spi/spi-cadence.c:690: warning: expecting prototype for
cdns_spi_runtime_suspend(). Prototype was for cnds_runtime_suspend()
instead
Fixes:
d36ccd9f7ea4 ("spi: cadence: Runtime pm adaptation")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20220322150018.12736-1-amit.kumar-mahapatra@xilinx.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Kamal Dasu [Mon, 28 Mar 2022 14:24:42 +0000 (10:24 -0400)]
spi: bcm-qspi: fix MSPI only access with bcm_qspi_exec_mem_op()
This fixes case where MSPI controller is used to access spi-nor
flash and BSPI block is not present.
Fixes:
5f195ee7d830 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220328142442.7553-1-kdasu.kdev@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Matthias Schiffer [Thu, 31 Mar 2022 11:08:19 +0000 (13:08 +0200)]
spi: cadence-quadspi: fix protocol setup for non-1-1-X operations
cqspi_set_protocol() only set the data width, but ignored the command
and address width (except for 8-8-8 DTR ops), leading to corruption of
all transfers using 1-X-X or X-X-X ops. Fix by setting the other two
widths as well.
While we're at it, simplify the code a bit by replacing the
CQSPI_INST_TYPE_* constants with ilog2().
Tested on a TI AM64x with a Macronix MX25U51245G QSPI flash with 1-4-4
read and write operations.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20220331110819.133392-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Vinod Koul [Wed, 6 Apr 2022 13:22:38 +0000 (18:52 +0530)]
spi: core: add dma_map_dev for __spi_unmap_msg()
Commit
b470e10eb43f ("spi: core: add dma_map_dev for dma device") added
dma_map_dev for _spi_map_msg() but missed to add for unmap routine,
__spi_unmap_msg(), so add it now.
Fixes:
b470e10eb43f ("spi: core: add dma_map_dev for dma device")
Cc: stable@vger.kernel.org # v5.14+
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20220406132238.1029249-1-vkoul@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown [Tue, 5 Apr 2022 09:25:09 +0000 (10:25 +0100)]
spi: mediatek: add single/quad mode support
Merge series from Leilk Liu <leilk.liu@mediatek.com>:
This series of patches are based on spi for-next, and provide 3 patches
to support MT7986.
Jakob Koschel [Thu, 24 Mar 2022 07:25:34 +0000 (08:25 +0100)]
spi: spidev: replace usage of found with dedicated list iterator variable
To move the list iterator variable into the list_for_each_entry_*()
macro in the future it should be avoided to use the list iterator
variable after the loop body.
To *never* use the list iterator variable after the loop it was
concluded to use a separate iterator variable instead of a
found boolean [1].
This removes the need to use a found variable and simply checking if
the variable was set, can determine if the break/goto was hit.
Link: https://lore.kernel.org/all/CAHk-=wgRr_D8CB-D9Kg-c=EHreAsk5SqXPwr9Y7k9sA6cWXJ6w@mail.gmail.com/
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220324072534.63420-1-jakobkoschel@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe Leroy [Sat, 2 Apr 2022 09:50:21 +0000 (11:50 +0200)]
spi: Prepare cleanup of powerpc's asm/prom.h
powerpc's asm/prom.h brings some headers that it doesn't
need itself.
In order to clean it up, first add missing headers in
users of asm/prom.h
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/5ed3298d8b5b1b5bf681d79584c61cb495852f4e.1648833423.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
Kuldeep Singh [Mon, 28 Mar 2022 19:20:06 +0000 (00:50 +0530)]
spi: qcom-qspi: Add minItems to interconnect-names
Add minItems constraint to interconnect-names as well. The schema
currently tries to match 2 names and fail for DTs with single entry.
With the change applied, below interconnect-names values are possible:
['qspi-config'], ['qspi-config', 'qspi-memory']
Fixes:
8f9c291558ea ("dt-bindings: spi: Add interconnect binding for QSPI")
Signed-off-by: Kuldeep Singh <singh.kuldeep87k@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220328192006.18523-1-singh.kuldeep87k@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 23 Mar 2022 14:02:15 +0000 (16:02 +0200)]
spi: spidev: Replace OF specific code by device property API
Instead of calling the OF specific APIs, use device property ones.
It also prevents misusing PRP0001 in ACPI when trying to instantiate
spidev directly. We only support special SPI test devices there.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220323140215.2568-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 23 Mar 2022 14:02:14 +0000 (16:02 +0200)]
spi: spidev: Replace ACPI specific code by device_get_match_data()
Instead of calling the ACPI specific APIs, use device_get_match_data().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220323140215.2568-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Andy Shevchenko [Wed, 23 Mar 2022 14:02:13 +0000 (16:02 +0200)]
spi: spidev: Convert BUILD_BUG_ON() to static_assert()
static_assert() is a preferred method to fail build when the certain
constraints are not met. Convert BUILD_BUG_ON() to static_assert().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220323140215.2568-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Leilk Liu [Mon, 21 Mar 2022 01:39:21 +0000 (09:39 +0800)]
spi: support hclk
this patch support hclk for AHB bus.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220321013922.24067-3-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Leilk Liu [Mon, 21 Mar 2022 01:39:22 +0000 (09:39 +0800)]
spi: mediatek: support hclk
this patch adds hclk support.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220321013922.24067-4-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Leilk Liu [Mon, 21 Mar 2022 01:39:20 +0000 (09:39 +0800)]
spi: mediatek: add spi memory support for ipm design
this patch add the support of spi-mem for ipm design.
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220321013922.24067-2-leilk.liu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Christophe JAILLET [Sun, 3 Apr 2022 10:11:13 +0000 (12:11 +0200)]
spi: mxic: Fix an error handling path in mxic_spi_probe()
If spi_register_master() fails, we must undo a previous
mxic_spi_mem_ecc_probe() call, as already done in the remove function.
Fixes:
00360ebae483 ("spi: mxic: Add support for pipelined ECC operations")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/09c81f751241f6ec0bac7a48d4ec814a742e0d17.1648980664.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Mark Brown <broonie@kernel.org>
Geert Uytterhoeven [Tue, 29 Mar 2022 14:00:39 +0000 (16:00 +0200)]
spi: rpc-if: Fix RPM imbalance in probe error path
If rpcif_hw_init() fails, Runtime PM is left enabled.
Fixes:
b04cc0d912eb80d3 ("memory: renesas-rpc-if: Add support for RZ/G2L")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/1c78a1f447d019bb66b6e7787f520ae78821e2ae.1648562287.git.geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
Linus Torvalds [Sun, 3 Apr 2022 21:08:21 +0000 (14:08 -0700)]
Linux 5.18-rc1
Linus Torvalds [Sun, 3 Apr 2022 19:26:01 +0000 (12:26 -0700)]
Merge tag 'trace-v5.18-2' of git://git./linux/kernel/git/rostedt/linux-trace
Pull more tracing updates from Steven Rostedt:
- Rename the staging files to give them some meaning. Just
stage1,stag2,etc, does not show what they are for
- Check for NULL from allocation in bootconfig
- Hold event mutex for dyn_event call in user events
- Mark user events to broken (to work on the API)
- Remove eBPF updates from user events
- Remove user events from uapi header to keep it from being installed.
- Move ftrace_graph_is_dead() into inline as it is called from hot
paths and also convert it into a static branch.
* tag 'trace-v5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Move user_events.h temporarily out of include/uapi
ftrace: Make ftrace_graph_is_dead() a static branch
tracing: Set user_events to BROKEN
tracing/user_events: Remove eBPF interfaces
tracing/user_events: Hold event_mutex during dyn_event_add
proc: bootconfig: Add null pointer check
tracing: Rename the staging files for trace_events
Linus Torvalds [Sun, 3 Apr 2022 19:21:14 +0000 (12:21 -0700)]
Merge tag 'clk-for-linus' of git://git./linux/kernel/git/clk/linux
Pull clk fix from Stephen Boyd:
"A single revert to fix a boot regression seen when clk_put() started
dropping rate range requests. It's best to keep various systems
booting so we'll kick this out and try again next time"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
Revert "clk: Drop the rate range on clk_put()"
Linus Torvalds [Sun, 3 Apr 2022 19:15:47 +0000 (12:15 -0700)]
Merge tag 'x86-urgent-2022-04-03' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of x86 fixes and updates:
- Make the prctl() for enabling dynamic XSTATE components correct so
it adds the newly requested feature to the permission bitmap
instead of overwriting it. Add a selftest which validates that.
- Unroll string MMIO for encrypted SEV guests as the hypervisor
cannot emulate it.
- Handle supervisor states correctly in the FPU/XSTATE code so it
takes the feature set of the fpstate buffer into account. The
feature sets can differ between host and guest buffers. Guest
buffers do not contain supervisor states. So far this was not an
issue, but with enabling PASID it needs to be handled in the buffer
offset calculation and in the permission bitmaps.
- Avoid a gazillion of repeated CPUID invocations in by caching the
values early in the FPU/XSTATE code.
- Enable CONFIG_WERROR in x86 defconfig.
- Make the X86 defconfigs more useful by adapting them to Y2022
reality"
* tag 'x86-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu/xstate: Consolidate size calculations
x86/fpu/xstate: Handle supervisor states in XSTATE permissions
x86/fpu/xsave: Handle compacted offsets correctly with supervisor states
x86/fpu: Cache xfeature flags from CPUID
x86/fpu/xsave: Initialize offset/size cache early
x86/fpu: Remove unused supervisor only offsets
x86/fpu: Remove redundant XCOMP_BV initialization
x86/sev: Unroll string mmio with CC_ATTR_GUEST_UNROLL_STRING_IO
x86/config: Make the x86 defconfigs a bit more usable
x86/defconfig: Enable WERROR
selftests/x86/amx: Update the ARCH_REQ_XCOMP_PERM test
x86/fpu/xstate: Fix the ARCH_REQ_XCOMP_PERM implementation
Linus Torvalds [Sun, 3 Apr 2022 19:08:26 +0000 (12:08 -0700)]
Merge tag 'core-urgent-2022-04-03' of git://git./linux/kernel/git/tip/tip
Pull RT signal fix from Thomas Gleixner:
"Revert the RT related signal changes. They need to be reworked and
generalized"
* tag 'core-urgent-2022-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
Revert "signal, x86: Delay calling signals in atomic on RT enabled kernels"
Linus Torvalds [Sun, 3 Apr 2022 17:31:00 +0000 (10:31 -0700)]
Merge tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping
Pull more dma-mapping updates from Christoph Hellwig:
- fix a regression in dma remap handling vs AMD memory encryption (me)
- finally kill off the legacy PCI DMA API (Christophe JAILLET)
* tag 'dma-mapping-5.18-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: move pgprot_decrypted out of dma_pgprot
PCI/doc: cleanup references to the legacy PCI DMA API
PCI: Remove the deprecated "pci-dma-compat.h" API
Linus Torvalds [Sun, 3 Apr 2022 17:17:48 +0000 (10:17 -0700)]
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
- avoid unnecessary rebuilds for library objects
- fix return value of __setup handlers
- fix invalid input check for "crashkernel=" kernel option
- silence KASAN warnings in unwind_frame
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9191/1: arm/stacktrace, kasan: Silence KASAN warnings in unwind_frame()
ARM: 9190/1: kdump: add invalid input check for 'crashkernel=0'
ARM: 9187/1: JIVE: fix return value of __setup handler
ARM: 9189/1: decompressor: fix unneeded rebuilds of library objects
Stephen Boyd [Sun, 3 Apr 2022 02:28:18 +0000 (19:28 -0700)]
Revert "clk: Drop the rate range on clk_put()"
This reverts commit
7dabfa2bc4803eed83d6f22bd6f045495f40636b. There are
multiple reports that this breaks boot on various systems. The common
theme is that orphan clks are having rates set on them when that isn't
expected. Let's revert it out for now so that -rc1 boots.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reported-by: Tony Lindgren <tony@atomide.com>
Reported-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Link: https://lore.kernel.org/r/366a0232-bb4a-c357-6aa8-636e398e05eb@samsung.com
Cc: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220403022818.39572-1-sboyd@kernel.org
Linus Torvalds [Sat, 2 Apr 2022 19:57:17 +0000 (12:57 -0700)]
Merge tag 'perf-tools-for-v5.18-2022-04-02' of git://git./linux/kernel/git/acme/linux
Pull more perf tools updates from Arnaldo Carvalho de Melo:
- Avoid SEGV if core.cpus isn't set in 'perf stat'.
- Stop depending on .git files for building PERF-VERSION-FILE, used in
'perf --version', fixing some perf tools build scenarios.
- Convert tracepoint.py example to python3.
- Update UAPI header copies from the kernel sources: socket,
mman-common, msr-index, KVM, i915 and cpufeatures.
- Update copy of libbpf's hashmap.c.
- Directly return instead of using local ret variable in
evlist__create_syswide_maps(), found by coccinelle.
* tag 'perf-tools-for-v5.18-2022-04-02' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
perf python: Convert tracepoint.py example to python3
perf evlist: Directly return instead of using local ret variable
perf cpumap: More cpu map reuse by merge.
perf cpumap: Add is_subset function
perf evlist: Rename cpus to user_requested_cpus
perf tools: Stop depending on .git files for building PERF-VERSION-FILE
tools headers cpufeatures: Sync with the kernel sources
tools headers UAPI: Sync drm/i915_drm.h with the kernel sources
tools headers UAPI: Sync linux/kvm.h with the kernel sources
tools kvm headers arm64: Update KVM headers from the kernel sources
tools arch x86: Sync the msr-index.h copy with the kernel sources
tools headers UAPI: Sync asm-generic/mman-common.h with the kernel
perf beauty: Update copy of linux/socket.h with the kernel sources
perf tools: Update copy of libbpf's hashmap.c
perf stat: Avoid SEGV if core.cpus isn't set