Meenakshi Venkataraman [Wed, 16 May 2012 20:35:57 +0000 (22:35 +0200)]
iwlwifi: update BT traffic load states correctly
commit
882dde8eb0d49ce0f853f8f4084dde56a21fe55f upstream.
When BT traffic load changes from its
previous state, a new LQ command needs to be
sent down to the firmware. This needs to
be done only once per change. The state
variable that keeps track of this change is
last_bt_traffic_load. However, it was not
being updated when the change had been
handled. Not updating this variable was
causing a flood of advanced BT config
commands to be sent to the firmware. Fix
this.
Signed-off-by: Meenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KyongHo [Tue, 29 May 2012 22:06:49 +0000 (15:06 -0700)]
mm: fix faulty initialization in vmalloc_init()
commit
dbda591d920b4c7692725b13e3f68ecb251e9080 upstream.
The transfer of ->flags causes some of the static mapping virtual
addresses to be prematurely freed (before the mapping is removed) because
VM_LAZY_FREE gets "set" if tmp->flags has VM_IOREMAP set. This might
cause subsequent vmalloc/ioremap calls to fail because it might allocate
one of the freed virtual address ranges that aren't unmapped.
va->flags has different types of flags from tmp->flags. If a region with
VM_IOREMAP set is registered with vm_area_add_early(), it will be removed
by __purge_vmap_area_lazy().
Fix vmalloc_init() to correctly initialize vmap_area for the given
vm_struct.
Also initialise va->vm. If it is not set, find_vm_area() for the early
vm regions will always fail.
Signed-off-by: KyongHo Cho <pullip.cho@samsung.com>
Cc: "Olav Haugan" <ohaugan@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michal Hocko [Tue, 29 May 2012 22:06:45 +0000 (15:06 -0700)]
mm: consider all swapped back pages in used-once logic
commit
e48982734ea0500d1eba4f9d96195acc5406cad6 upstream.
Commit
645747462435 ("vmscan: detect mapped file pages used only once")
made mapped pages have another round in inactive list because they might
be just short lived and so we could consider them again next time. This
heuristic helps to reduce pressure on the active list with a streaming
IO worklods.
This patch fixes a regression introduced by this commit for heavy shmem
based workloads because unlike Anon pages, which are excluded from this
heuristic because they are usually long lived, shmem pages are handled
as a regular page cache.
This doesn't work quite well, unfortunately, if the workload is mostly
backed by shmem (in memory database sitting on 80% of memory) with a
streaming IO in the background (backup - up to 20% of memory). Anon
inactive list is full of (dirty) shmem pages when watermarks are hit.
Shmem pages are kept in the inactive list (they are referenced) in the
first round and it is hard to reclaim anything else so we reach lower
scanning priorities very quickly which leads to an excessive swap out.
Let's fix this by excluding all swap backed pages (they tend to be long
lived wrt. the regular page cache anyway) from used-once heuristic and
rather activate them if they are referenced.
The customer's workload is shmem backed database (80% of RAM) and they
are measuring transactions/s with an IO in the background (20%).
Transactions touch more or less random rows in the table. The
transaction rate fell by a factor of 3 (in the worst case) because of
commit
64574746. This patch restores the previous numbers.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Minchan Kim <minchan@kernel.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sasha Levin [Tue, 29 May 2012 22:06:15 +0000 (15:06 -0700)]
mm: fix NULL ptr deref when walking hugepages
commit
08fa29d916c6e271ad13978cd993e7238c68db97 upstream.
A missing validation of the value returned by find_vma() could cause a
NULL ptr dereference when walking the pagetable.
This is triggerable from usermode by a simple user by trying to read a
page info out of /proc/pid/pagemap which doesn't exist.
Introduced by commit
025c5b2451e4 ("thp: optimize away unnecessary page
table locking").
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Siddhesh Poyarekar [Tue, 29 May 2012 22:06:22 +0000 (15:06 -0700)]
mm/fork: fix overflow in vma length when copying mmap on clone
commit
7edc8b0ac16cbaed7cb4ea4c6b95ce98d2997e84 upstream.
The vma length in dup_mmap is calculated and stored in a unsigned int,
which is insufficient and hence overflows for very large maps (beyond
16TB). The following program demonstrates this:
#include <stdio.h>
#include <unistd.h>
#include <sys/mman.h>
#define GIG 1024 * 1024 * 1024L
#define EXTENT 16393
int main(void)
{
int i, r;
void *m;
char buf[1024];
for (i = 0; i < EXTENT; i++) {
m = mmap(NULL, (size_t) 1 * 1024 * 1024 * 1024L,
PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANONYMOUS, 0, 0);
if (m == (void *)-1)
printf("MMAP Failed: %d\n", m);
else
printf("%d : MMAP returned %p\n", i, m);
r = fork();
if (r == 0) {
printf("%d: successed\n", i);
return 0;
} else if (r < 0)
printf("FORK Failed: %d\n", r);
else if (r > 0)
wait(NULL);
}
return 0;
}
Increase the storage size of the result to unsigned long, which is
sufficient for storing the difference between addresses.
Signed-off-by: Siddhesh Poyarekar <siddhesh.poyarekar@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jun'ichi Nomura [Tue, 22 May 2012 09:57:17 +0000 (18:57 +0900)]
SCSI: Fix dm-multipath starvation when scsi host is busy
commit
b7e94a1686c5daef4f649f7f4f839cc294f07710 upstream.
block congestion control doesn't have any concept of fairness across
multiple queues. This means that if SCSI reports the host as busy in
the queue congestion control it can result in an unfair starvation
situation in dm-mp if there are multiple multipath devices on the same
host. For example:
http://www.redhat.com/archives/dm-devel/2012-May/msg00123.html
The fix for this is to report only the sdev busy state (and ignore the
host busy state) in the block congestion control call back.
The host is still congested, but the SCSI subsystem will sort out the
congestion in a fair way because it knows the relation between the
queues and the host.
[jejb: fixed up trailing whitespace]
Reported-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Tested-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
James Bottomley [Wed, 30 May 2012 09:45:39 +0000 (09:45 +0000)]
SCSI: fix scsi_wait_scan
commit
1ff2f40305772b159a91c19590ee159d3a504afc upstream.
Commit
c751085943362143f84346d274e0011419c84202
Author: Rafael J. Wysocki <rjw@sisk.pl>
Date: Sun Apr 12 20:06:56 2009 +0200
PM/Hibernate: Wait for SCSI devices scan to complete during resume
Broke the scsi_wait_scan module in 2.6.30. Apparently debian still uses it so
fix it and backport to stable before removing it in 3.6.
The breakage is caused because the function template in
include/scsi/scsi_scan.h is defined to be a nop unless SCSI is built in.
That means that in the modular case (which is every distro), the
scsi_wait_scan module does a simple async_synchronize_full() instead of
waiting for scans.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lars-Peter Clausen [Mon, 9 Apr 2012 13:05:44 +0000 (15:05 +0200)]
microblaze: Do not select GENERIC_GPIO by default
commit
59516b07b4ffa7e607a5787674ea3c405f1b390c upstream.
The microblaze architecture does not provide a native GPIO API implementation
nor requires GPIOLIB, but still selects GENERIC_GPIO by default. As a result the
following build error occurs, if GPIOLIB is not selected:
include/asm-generic/gpio.h: In function 'gpio_get_value_cansleep':
include/asm-generic/gpio.h:218: error: implicit declaration of function '__gpio_get_value'
include/asm-generic/gpio.h: In function 'gpio_set_value_cansleep':
include/asm-generic/gpio.h:224: error: implicit declaration of function '__gpio_set_value'
This patch addresses the issue by not selecting GENERIC_GPIO by default. This
causes the GPIO API to be stubbed out if no implementation is provided.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Boaz Harrosh [Wed, 16 May 2012 11:22:21 +0000 (14:22 +0300)]
exofs: Fix CRASH on very early IO errors.
commit
6abe4a87f7bc7978705c386dbba0ca0c7790b3ec upstream.
If at exofs_fill_super() we had an early termination
do to any error, like an IO error while reading the
super-block. We would crash inside exofs_free_sbi().
This is because sbi->oc.numdevs was set to 1, before
we actually have a device table at all.
Fix it by moving the sbi->oc.numdevs = 1 to after the
allocation of the device table.
Reported-by: Johannes Schild <JSchild@gmx.de>
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 1 Jun 2012 07:18:44 +0000 (15:18 +0800)]
Linux 3.4.1
Laxman Dewangan [Mon, 7 May 2012 06:46:19 +0000 (12:16 +0530)]
i2c: tegra: notify transfer-complete after clearing status.
commit
c889e91d2cc22123f20f40dde0c0a91856a20eea upstream.
The notification of the transfer complete by calling complete()
should be done after clearing all interrupt status.
This avoids the race condition of misconfigure the i2c controller
in multi-core environment.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Marcus Folkesson [Thu, 3 May 2012 13:56:36 +0000 (15:56 +0200)]
i2c: davinci: Free requested IRQ in remove
commit
9868a060ccf769c08ec378a9829137e272e9a92c upstream.
The freed IRQ is not necessary the one requested in probe.
Even if it was, with two or more i2c-controllers it will fails anyway.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andi Kleen [Fri, 19 Nov 2010 12:16:22 +0000 (13:16 +0100)]
MCE: Fix vm86 handling for 32bit mce handler
commit
a129a7c84582629741e5fa6f40026efcd7a65bd4 upstream.
When running on 32bit the mce handler could misinterpret
vm86 mode as ring 0. This can affect whether it does recovery
or not; it was possible to panic when recovery was actually
possible.
Fix this by always forcing vm86 to look like ring 3.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stephen Warren [Sat, 12 May 2012 00:01:38 +0000 (18:01 -0600)]
ARM: dt: tegra cardhu: fix typo in SDHCI node name
commit
1dfebb426cfd16e2080f8c95e00ca2462f2325d4 upstream.
Cardhu's eMMC controller is on sdhci@
78000600, not sdhci@
78000400.
Fix the typo. This roughly doubles the IO performance, since the
support-8bit property actually takes effect.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dima Zavin [Mon, 30 Apr 2012 09:26:14 +0000 (10:26 +0100)]
ARM: 7409/1: Do not call flush_cache_user_range with mmap_sem held
commit
435a7ef52db7d86e67a009b36cac1457f8972391 upstream.
We can't be holding the mmap_sem while calling flush_cache_user_range
because the flush can fault. If we fault on a user address, the
page fault handler will try to take mmap_sem again. Since both places
acquire the read lock, most of the time it succeeds. However, if another
thread tries to acquire the write lock on the mmap_sem (e.g. mmap) in
between the call to flush_cache_user_range and the fault, the down_read
in do_page_fault will deadlock.
[will: removed drop of vma parameter as already queued by rmk (7365/1)]
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Dima Zavin <dima@android.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dima Zavin [Thu, 29 Mar 2012 19:44:06 +0000 (20:44 +0100)]
ARM: 7365/1: drop unused parameter from flush_cache_user_range
commit
4542b6a0fa6b48d9ae6b41c1efeb618b7a221b2a upstream.
vma isn't used and flush_cache_user_range isn't a standard macro that
is used on several archs with the same prototype. In fact only unicore32
has a macro with the same name (with an identical implementation and no
in-tree users).
This is a part of a patch proposed by Dima Zavin (with Message-id:
1272439931-12795-1-git-send-email-dima@android.com) that didn't get
accepted.
Cc: Dima Zavin <dima@android.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Sun, 13 May 2012 17:09:38 +0000 (20:09 +0300)]
iommu: Fix off by one in dmar_get_fault_reason()
commit
fefe1ed1398b81e3fadc92d11d91162d343c8836 upstream.
fault_reason - 0x20 == ARRAY_SIZE(irq_remap_fault_reasons) is
one past the end of the array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Joerg Roedel <joerg.roedel@amd.com>
Cc: Youquan Song <youquan.song@intel.com>
Cc: walter harms <wharms@bfs.de>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/20120513170938.GA4280@elgon.mountain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
[bwh: Backported to 3.2: s/irq_remap_fault_reasons/intr_remap_fault_reasons/]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Woodhouse [Fri, 25 May 2012 16:42:54 +0000 (17:42 +0100)]
intel-iommu: Add device info into list before doing context mapping
commit
e2ad23d04c1304431ab5176c89b7b476ded2d995 upstream.
Add device info into list before doing context mapping, because device
info will be used by iommu_enable_dev_iotlb(). Without it, ATS won't get
enabled as it should be.
ATS, while a dubious decision from a security point of view, can be very
important for performance.
Signed-off-by: Xudong Hao <xudong.hao@intel.com>
Signed-off-by: Xiantao Zhang <xiantao.zhang@intel.com>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Metcalf [Fri, 25 May 2012 16:32:09 +0000 (12:32 -0400)]
tile: fix bug where fls(0) was not returning 0
commit
9f1d62bed7f015d11b9164078b7fea433b474114 upstream.
This is because __builtin_clz(0) returns 64 for the "undefined" case
of 0, since the builtin just does a right-shift 32 and "clz" instruction.
So, use the alpha approach of casting to u32 and using __builtin_clzll().
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ming Lei [Thu, 17 May 2012 02:27:12 +0000 (10:27 +0800)]
mmc: omap_hsmmc: pass IRQF_ONESHOT to request_threaded_irq
commit
db35f83ef47b5f180f2670d11f5f93992314ea09 upstream.
The flag of IRQF_ONESHOT should be passed to request_threaded_irq,
otherwise the following failure message should be dumped because
hardware handler is defined as NULL:
[ 3.383483] genirq: Threaded irq requested with handler=NULL and
!ONESHOT for irq 368
[ 3.392730] omap_hsmmc: probe of omap_hsmmc.0 failed with error -22
The patch fixes one kernel hang bug which is caused by mmc card
probe failure and root device can't be brought up.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Guennadi Liakhovetski [Tue, 24 Apr 2012 15:56:29 +0000 (17:56 +0200)]
mmc: cd-gpio: protect against NULL context in mmc_cd_gpio_free()
commit
0e9f480bb553d39ee06ccd45639ba7a5446a7b81 upstream.
Do not oops, even if mmc_cd_gpio_free() is mistakenly called on a driver
cleanup path, even though a previous call to mmc_cd_gpio_request() failed.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
[stable@: please apply to 3.3-stable]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Pitre [Mon, 16 Apr 2012 23:16:54 +0000 (19:16 -0400)]
mmc: sdio: avoid spurious calls to interrupt handlers
commit
bbbc4c4d8c5face097d695f9bf3a39647ba6b7e7 upstream.
Commit
06e8935feb ("optimized SDIO IRQ handling for single irq")
introduced some spurious calls to SDIO function interrupt handlers,
such as when the SDIO IRQ thread is started, or the safety check
performed upon a system resume. Let's add a flag to perform the
optimization only when a real interrupt is signaled by the host
driver and we know there is no point confirming it.
Reported-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Luck [Wed, 23 May 2012 21:14:22 +0000 (14:14 -0700)]
x86/mce: Fix check for processor context when machine check was taken.
commit
875e26648cf9b6db9d8dc07b7959d7c61fb3f49c upstream.
Linus pointed out that there was no value is checking whether m->ip
was zero - because zero is a legimate value. If we have a reliable
(or faked in the VM86 case) "m->cs" we can use it to tell whether we
were in user mode or kernelwhen the machine check hit.
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H. Peter Anvin [Thu, 24 May 2012 14:01:38 +0000 (07:01 -0700)]
x86, relocs: Add jiffies and jiffies_64 to the relative whitelist
commit
ea17e7414bc62e8d3bde8d08e3df1d921c518c17 upstream.
The symbol jiffies is created in the linker script as an alias to
jiffies_64. Unfortunately this is done outside any section, and
apparently GNU ld 2.21 doesn't carry the section with it, so we end up
with an absolute symbol and therefore a broken kernel.
Add jiffies and jiffies_64 to the whitelist.
The most disturbing bit with this discovery is that it shows that we
have had multiple linker bugs in this area crossing multiple
generations, and have been silently building bad kernels for some time.
Link: http://lkml.kernel.org/r/20120524171604.0d98284f3affc643e9714470@canb.auug.org.au
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
H. Peter Anvin [Wed, 23 May 2012 21:02:34 +0000 (14:02 -0700)]
x86-32, relocs: Whitelist more symbols for ld bug workaround
commit
fd952815307f0f272bf49fd364a7fd2f9992bc42 upstream.
As noted in checkin:
a3e854d95 x86, relocs: Workaround for binutils 2.22.52.0.1 section bug
ld version 2.22.52.0.[12] can incorrectly promote relative symbols to
absolute, if the output section they appear in is otherwise empty.
Since checkin:
6520fe55 x86, realmode: 16-bit real-mode code support for relocs tool
we actually check for this and error out rather than silently creating
a kernel which will malfunction if relocated.
Ingo found a configuration in which __start_builtin_fw triggered the
warning.
Go through the linker script sources and look for more symbols that
could plausibly get bogusly promoted to absolute, and add them to the
whitelist.
In general, if the following error triggers:
Invalid absolute R_386_32 relocation: <symbol>
... then we should verify that <symbol> is really meant to be
relocated, and add it and any related symbols manually to the S_REL
regexp.
Please note that
6520fe55 does not introduce the error, only the check
for the error -- without
6520fe55 this version of ld will simply
produce a corrupt kernel if CONFIG_RELOCATABLE is set on x86-32.
Reported-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jarkko Sakkinen [Mon, 21 May 2012 17:51:24 +0000 (20:51 +0300)]
x86, relocs: Build clean fix
commit
b2d668da9307c4c163dd603d2bb3cadb10f9fd37 upstream.
relocs was not cleaned up when "make clean" is issued. This
patch fixes the issue.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Link: http://lkml.kernel.org/r/1337622684-6834-1-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart [Wed, 21 Mar 2012 12:50:36 +0000 (09:50 -0300)]
media: uvcvideo: Fix ENUMINPUT handling
commit
31c5f0c5e25ed71eeced170f113bb590f2f1f6f3 upstream.
Properly validate the user-supplied index against the number of inputs.
The code used the pin local variable instead of the index by mistake.
Reported-by: Jozef Vesely <vesely@gjh.sk>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Michael Krufky [Thu, 22 Mar 2012 16:55:05 +0000 (13:55 -0300)]
smsusb: add autodetection support for USB ID 2040:c0a0
commit
4d1b58b84472d1d300a66e1c5fd765b21e74ba15 upstream.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dave Airlie [Fri, 18 May 2012 14:31:12 +0000 (15:31 +0100)]
nouveau: nouveau_set_bo_placement takes TTM flags
commit
c284815debba2f14ee2fd07b1b4cc972ab116110 upstream.
This seems to be wrong to me, spotted while thinking about dma-buf.
Reviewed-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stefano Stabellini [Mon, 21 May 2012 15:54:10 +0000 (16:54 +0100)]
xen: do not map the same GSI twice in PVHVM guests.
commit
68c2c39a76b094e9b2773e5846424ea674bf2c46 upstream.
PV on HVM guests map GSIs into event channels. At restore time the
event channels are resumed by restore_pirqs.
Device drivers might try to register the same GSI again through ACPI at
restore time, but the GSI has already been mapped and bound by
restore_pirqs. This patch detects these situations and avoids
mapping the same GSI multiple times.
Without this patch we get:
(XEN) irq.c:2235: dom4: pirq 23 or emuirq 28 already mapped
and waste a pirq.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Carpenter [Tue, 15 May 2012 08:47:47 +0000 (11:47 +0300)]
hvc_xen: NULL dereference on allocation failure
commit
201a52bea928687b7557728b176ac4f8a37d5cbd upstream.
If kzalloc() returns a NULL here, we pass a NULL to
xencons_disconnect_backend() which will cause an Oops.
Also I removed the __GFP_ZERO while I was at it since kzalloc() implies
__GFP_ZERO.
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Herton Ronaldo Krzesinski [Fri, 11 May 2012 22:29:50 +0000 (15:29 -0700)]
spi/spi-fsl-spi: reference correct pdata in fsl_spi_cs_control
commit
067aa4815a9bc12a569d8a06afef50ba5773afbf upstream.
Commit
178db7d3, "spi: Fix device unregistration when unregistering
the bus master", changed spi device initialization of dev.parent pointer
to be the master's device pointer instead of his parent.
This introduced a bug in spi-fsl-spi, since its usage of spi device
pointer was not updated accordingly. This was later fixed by commit
5039a86, "spi/mpc83xx: fix NULL pdata dereference bug", but it missed
another spot on fsl_spi_cs_control function where we also need to update
usage of spi device pointer. This change address that.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Thu, 3 May 2012 10:22:06 +0000 (12:22 +0200)]
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
commit
d6de85e85edcc38c9edcde45a0a568818fcddc13 upstream.
commit
cfadd838(powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO
driver) added an unconditional call of chip->irq_eoi() to the demux
handler.
This leads to a NULL pointer derefernce on MPC512x platforms which use
this driver as well.
Make it conditional.
Reported-by: Thomas Wucher <thwucher@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Felix Radensky <felix@embedded-sol.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Vetter [Sun, 13 May 2012 20:29:25 +0000 (22:29 +0200)]
drm/i915: don't clobber the pipe param in sanitize_modesetting
commit
a9dcf84b14ef4e9a609910367576995e6f32f3dc upstream.
... we need it later on in the function to clean up pipe <-> plane
associations. This regression has been introduced in
commit
f47166d2b0001fcb752b40c5a2d4db986dfbea68
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Mar 22 15:00:50 2012 +0000
drm/i915: Sanitize BIOS debugging bits from PIPECONF
Spotted by staring at debug output of an (as it turns out) totally
unrelated bug.
v2: I've totally failed to do the s/pipe/i/ correctly, spotted by
Chris Wilson.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Ben Widawsky [Sun, 15 Apr 2012 01:41:32 +0000 (18:41 -0700)]
drm/i915: [GEN7] Use HW scheduler for fixed function shaders
commit
a1e969e0332de7a430e62822cee8f2ec8d83cd7c upstream.
This originally started as a patch from Bernard as a way of simply
setting the VS scheduler. After submitting the RFC patch, we decided to
also modify the DS scheduler. To be most explicit, I've made the patch
explicitly set all scheduler modes, and included the defines for other
modes (in case someone feels frisky later).
The rest of the story gets a bit weird. The first version of the patch
showed an almost unbelievable performance improvement. Since rebasing my
branch it appears the performance improvement has gone, unfortunately.
But setting these bits seem to be the right thing to do given that the
docs describe corruption that can occur with the default settings.
In summary, I am seeing no more perf improvements (or regressions) in my
limited testing, but we believe this should be set to prevent rendering
corruption, therefore cc stable.
v1: Clear bit 4 also (Ken + Eugeni)
Do a full clear + set of the bits we want (Me).
Cc: Bernard Kilarski <bernard.r.kilarski@intel.com>
Reviewed-by (RFC): Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <benjamin.widawsky@intel.com>
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Chris Wilson [Wed, 9 May 2012 20:45:43 +0000 (21:45 +0100)]
drm/i915: Avoid a double-read of PCH_IIR during interrupt handling
commit
9adab8b5a7fde248504f484e197589f3e3c922e2 upstream.
Currently the code re-reads PCH_IIR during the hotplug interrupt
processing. Not only is this a wasted read, but introduces a potential
for handling a spurious interrupt as we then may not clear all the
interrupts processed (since the re-read IIR may contains more interrupts
asserted than we clear using the result of the original read).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Larry Finger [Sun, 6 May 2012 21:01:05 +0000 (16:01 -0500)]
b43legacy: Fix error due to MMIO access with SSB unpowered
commit
8f4b20388fa77226a3605627a33a23f90d559e50 upstream.
There is a dummy read of a PCI MMIO register that occurs before the SSB bus
has been powered, which is an error. This bug has not been seen earlier,
but was apparently exposed when udev was updated to version 182.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Mon, 21 May 2012 14:27:44 +0000 (15:27 +0100)]
gma500: Fix Poulsbo suspend/resume crash on devices with SDVO ports
commit
7beff62ee39d3ccf088bb77f61a63037f714d235 upstream.
Reported-by: Guillaume Clément <guillaume@baobob.org>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andiry Xu [Fri, 4 May 2012 16:50:10 +0000 (00:50 +0800)]
usbcore: enable USB2 LPM if port suspend fails
commit
c3e751e4f4754793bb52bd5ae30e9cc027edbb12 upstream.
USB2 LPM is disabled when device begin to suspend and enabled after device
is resumed. That's because USB spec does not define the transition from
U1/U2 state to U3 state.
If usb_port_suspend() fails, usb_port_resume() is never called, and USB2 LPM
is disabled in this situation. Enable USB2 LPM if port suspend fails.
This patch should be backported to kernels as old as 3.2, that contain
the commit
65580b4321eb36f16ae8b5987bfa1bb948fc5112 "xHCI: set USB2
hardware LPM".
Signed-off-by: Andiry Xu <andiry.xu@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Thu, 10 May 2012 08:19:21 +0000 (10:19 +0200)]
USB: fix resource leak in xhci power loss path
commit
f8a9e72d125f4e00ec529ba67b674321a1f3bf31 upstream.
Some more data structures must be freed and counters
reset if an XHCI controller has lost power. The failure
to do so renders some chips inoperative after a certain number
of S4 cycles.
This patch should be backported to kernels as old as 3.2,
that contain the commits
c29eea621900f18287d50519f72cb9113746d75a
"xhci: Implement HS/FS/LS bandwidth checking." and
commit
839c817ce67178ca3c7c7ad534c571bba1e69ebe
"xhci: Implement HS/FS/LS bandwidth checking."
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Tue, 8 May 2012 16:22:49 +0000 (09:22 -0700)]
xhci: Add new short TX quirk for Fresco Logic host.
commit
1530bbc6272d9da1e39ef8e06190d42c13a02733 upstream.
Sergio reported that when he recorded audio from a USB headset mic
plugged into the USB 3.0 port on his ASUS N53SV-DH72, the audio sounded
"robotic". When plugged into the USB 2.0 port under EHCI on the same
laptop, the audio sounded fine. The device is:
Bus 002 Device 004: ID 046d:0a0c Logitech, Inc. Clear Chat Comfort USB Headset
The problem was tracked down to the Fresco Logic xHCI host controller
not correctly reporting short transfers on isochronous IN endpoints.
The driver would submit a 96 byte transfer, the device would only send
88 or 90 bytes, and the xHCI host would report the transfer had a
"successful" completion code, with an untransferred buffer length of 8
or 6 bytes.
The successful completion code and non-zero untransferred length is a
contradiction. The xHCI host is supposed to only mark a transfer as
successful if all the bytes are transferred. Otherwise, the transfer
should be marked with a short packet completion code. Without the EHCI
bus trace, we wouldn't know whether the xHCI driver should trust the
completion code or the untransferred length. With it, we know to trust
the untransferred length.
Add a new xHCI quirk for the Fresco Logic host controller. If a
transfer is reported as successful, but the untransferred length is
non-zero, print a warning. For the Fresco Logic host, change the
completion code to COMP_SHORT_TX and process the transfer like a short
transfer.
This should be backported to stable kernels that contain the commit
f5182b4155b9d686c5540a6822486400e34ddd98 "xhci: Disable MSI for some
Fresco Logic hosts." That commit was marked for stable kernels as old
as 2.6.36.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Sergio Correia <lists@uece.net>
Tested-by: Sergio Correia <lists@uece.net>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Tue, 8 May 2012 14:09:26 +0000 (07:09 -0700)]
xhci: Reset reserved command ring TRBs on cleanup.
commit
33b2831ac870d50cc8e01c317b07fb1e69c13fe1 upstream.
When the xHCI driver needs to clean up memory (perhaps due to a failed
register restore on resume from S3 or resume from S4), it needs to reset
the number of reserved TRBs on the command ring to zero. Otherwise,
several resume cycles (about 30) with a UAS device attached will
continually increment the number of reserved TRBs, until all command
submissions fail because there isn't enough room on the command ring.
This patch should be backported to kernels as old as 2.6.32,
that contain the commit
913a8a344ffcaf0b4a586d6662a2c66a7106557d
"USB: xhci: Change how xHCI commands are handled."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede [Mon, 23 Apr 2012 13:06:09 +0000 (15:06 +0200)]
usb-xhci: Handle COMP_TX_ERR for isoc tds
commit
9c745995ae5c4ff787f34a359de908facc11ee00 upstream.
While testing unplugging an UVC HD webcam with usb-redirection (so through
usbdevfs), my userspace usb-redir code was getting a value of -1 in
iso_frame_desc[n].status, which according to Documentation/usb/error-codes.txt
is not a valid value.
The source of this -1 is the default case in xhci-ring.c:process_isoc_td()
adding a kprintf there showed the value of trb_comp_code to be COMP_TX_ERR
in this case, so this patch adds handling for that completion code to
process_isoc_td().
This was observed and tested with the following xhci controller:
1033:0194 NEC Corporation uPD720200 USB 3.0 Host Controller (rev 04)
Note: I also wonder if setting frame->status to -1 (-EPERM) is the best we can
do, but since I cannot come up with anything better I've left that as is.
This patch should be backported to kernels as old as 2.6.36, which contain the
commit
04e51901dd44f40a5a385ced897f6bca87d5f40a "USB: xHCI: Isochronous
transfer implementation".
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Mon, 16 Apr 2012 17:56:47 +0000 (10:56 -0700)]
xhci: Avoid dead ports when CONFIG_USB_XHCI_HCD=n
commit
51c9e6c7732b67769c0a514d31f505e49fa82dd4 upstream.
If the user chooses to say "no" to CONFIG_USB_XHCI_HCD on a system
with an Intel Panther Point chipset, the PCI quirks code or the EHCI
driver will switch the ports over to the xHCI host, but the xHCI driver
will never load. The ports will be powered off and seem "dead" to the
user.
Fix this by only switching the ports over if CONFIG_USB_XHCI_HCD is
either compiled in, or compiled as a module.
This patch should be backported to stable kernels as old as 3.0,
that contain commit
69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: Eric Anholt <eric.anholt@intel.com>
Reported-by: David Bein <d.bein@f5.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Andiry Xu [Fri, 13 Apr 2012 18:54:30 +0000 (02:54 +0800)]
xHCI: keep track of ports being resumed and indicate in hub_status_data
commit
f370b9968a220a3d79d870dd7dee674cc0ff3d10 upstream.
This commit adds a bit-array to xhci bus_state for keeping track of
which ports are undergoing a resume transition. If any of the bits
are set when xhci_hub_status_data() is called, the routine will return
a non-zero value even if no ports have any status changes pending.
This will allow usbcore to handle races between root-hub suspend and
port wakeup.
This patch should be backported to kernels as old as 3.4, that contain
the commit
879d38e6bc36d73b0ac40ec9b0d839fda9fa8b1a "USB: fix race
between root-hub suspend and remote wakeup".
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Sarah Sharp [Thu, 9 Feb 2012 23:55:13 +0000 (15:55 -0800)]
xhci: Add Lynx Point to list of Intel switchable hosts.
commit
1c12443ab8eba71a658fae4572147e56d1f84f66 upstream.
The upcoming Intel Lynx Point chipset includes an xHCI host controller
that can have ports switched from the EHCI host controller, just like
the Intel Panther Point xHCI host. This time, ports from both EHCI
hosts can be switched to the xHCI host controller. The PCI config
registers to do the port switching are in the exact same place in the
xHCI PCI configuration registers, with the same semantics.
Hooray for shipping patches for next-gen hardware before the current gen
hardware is even available for purchase!
This patch should be backported to stable kernels as old as 3.0,
that contain commit
69e848c2090aebba5698a1620604c7dccb448684
"Intel xhci: Support EHCI/xHCI port switching."
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steffen Müller [Mon, 30 Apr 2012 11:05:34 +0000 (13:05 +0200)]
usb: add USB_QUIRK_RESET_RESUME for M-Audio 88es
commit
166cb70e97bd83d7ae9bbec6ae59a178fd9bb823 upstream.
Tested-by: Steffen Müller <steffen.mueller@radio-frei.de>
Signed-off-by: Steffen Müller <steffen.mueller@radio-frei.de>
Signed-off-by: Stefan Seyfried <seife+kernel@b1-systems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter Chen [Sun, 1 Apr 2012 07:17:16 +0000 (15:17 +0800)]
usb: gadget: fsl_udc_core: dTD's next dtd pointer need to be updated once written
commit
4d0947dec4db1224354e2f6f00ae22ce38e62a43 upstream.
dTD's next dtd pointer need to be updated once CPU writes it, or this
request may not be handled by controller, then host will get NAK from
device forever.
This problem occurs when there is a request is handling, we need to add
a new request to dTD list, if this new request is added before the current
one is finished, the new request is intended to added as next dtd pointer
at current dTD, but without wmb(), the dTD's next dtd pointer may not be
updated when the controller reads it. In that case, the controller will
still get Terminate Bit is 1 at dTD's next dtd pointer, that means there is
no next request, then this new request is missed by controller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Darren Hart [Fri, 11 May 2012 20:56:57 +0000 (13:56 -0700)]
USB: serial: ti_usb_3410_5052: Add support for the FRI2 serial console
commit
975dc33b82cb887d75a29b1e3835c8eb063a8e99 upstream.
The Kontron M2M development board, also known as the Fish River Island II,
has an optional daughter card providing access to the PCH_UART (EG20T) via
a ti_usb_3410_5052 uart to usb chip.
http://us.kontron.com/products/systems+and+platforms/m2m/m2m+smart+services+developer+kit.html
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Al Borchers <alborchers@steinerpoint.com>
CC: Peter Berger <pberger@brimson.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Huajun Li [Fri, 18 May 2012 12:12:51 +0000 (20:12 +0800)]
USB: Remove races in devio.c
commit
4e09dcf20f7b5358615514c2ec8584b248ab8874 upstream.
There exist races in devio.c, below is one case,
and there are similar races in destroy_async()
and proc_unlinkurb(). Remove these races.
cancel_bulk_urbs() async_completed()
------------------- -----------------------
spin_unlock(&ps->lock);
list_move_tail(&as->asynclist,
&ps->async_completed);
wake_up(&ps->wait);
Lead to free_async() be triggered,
then urb and 'as' will be freed.
usb_unlink_urb(as->urb);
===> refer to the freed 'as'
Signed-off-by: Huajun Li <huajun.li.lee@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Oncaphillis <oncaphillis@snafu.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Nicolas Ferre [Wed, 9 May 2012 08:48:54 +0000 (10:48 +0200)]
USB: ohci-at91: add a reset function to fix race condition
commit
07e4e556eff4938eb2edf2591de3aa7d7fb82b52 upstream.
A possible race condition appears because we are not initializing
the ohci->regs before calling usb_hcd_request_irqs().
We move the call to ohci_init() in hcd->driver->reset() instead of
hcd->driver->start() to fix this.
This was experienced when we share the same IRQ line between OHCI and EHCI
controllers.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Christian Eggers <christian.eggers@kathrein.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shinya Kuribayashi [Thu, 10 May 2012 01:31:21 +0000 (10:31 +0900)]
USB: gpio_vbus: provide an appropriate debounce interval
commit
934ccec4da14dc0586dfe08b36166364bdd2181b upstream.
In commit
c2344f13b59e007d782a3e591ebc551bc583a8b7 (USB: gpio_vbus:
add delayed vbus_session calls, 2009-01-24), usb_gadget_vbus_connect()
and ...disconnect() were extracted from the interrupt handler, so to
allow vbus_session handlers to deal with msleep() calls.
This patch takes the approach one step further.
USB2.0 specification (7.1.7.3 Connect and Disconnect Signaling) says
that the USB system software (shall) provide a debounce interval with
a minimum duration of 100 ms, which ensures that the electrical and
mechanical connection is stable before software attempts to reset
the attached device.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Russ Dill [Fri, 4 May 2012 11:24:47 +0000 (04:24 -0700)]
USB: EHCI: OMAP: Finish ehci omap phy reset cycle before adding hcd.
commit
3aa2ae74ba630ec9b98736d64aea8e4cb490861d upstream.
'ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue' (
1fcb57d0f) created a regression
with Beagleboard xM if booting the kernel after running 'usb start' under u-boot.
Finishing the reset before calling 'usb_add_hcd' fixes the regression. This is most likely due to
usb_add_hcd calling the driver's reset and init functions which expect the hardware to be
up and running.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hauke Mehrtens [Fri, 18 May 2012 18:29:56 +0000 (20:29 +0200)]
USB: ehci-platform: remove update_device
commit
8377c94f627f7943da9a7eefdb21fd2e9e7ec629 upstream.
The update_device callback is not needed and the function used here is
from the pci ehci driver. Without this patch we get a compile error if
ehci-platform is compiled without ehci-pci.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Paul Zimmerman [Mon, 16 Apr 2012 21:19:07 +0000 (14:19 -0700)]
usb: usbtest: two super speed fixes for usbtest
commit
6a23ccd216b6a8ba2c67a9f9d8969b4431ad2920 upstream.
bMaxPacketSize0 field for super speed is a power of 2, not a count.
The size itself is always 512.
Max packet size for a super speed bulk endpoint is 1024, so
allocate the urb size in halt_simple() accordingly.
Signed-off-by: Paul Zimmerman <paulz@synopsys.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Matthias Fend [Mon, 7 May 2012 12:37:30 +0000 (14:37 +0200)]
USB: ffs-test: fix length argument of out function call
commit
eb9c5836384cd2a276254df6254ed71117983626 upstream.
The out functions should only handle actual available data instead of the complete buffer.
Otherwise for example the ep0_consume function will report ghost events since it tries to decode
the complete buffer - which may contain partly invalid data.
Signed-off-by: Matthias Fend <matthias.fend@wolfvision.net>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Tue, 8 May 2012 19:15:25 +0000 (15:15 -0400)]
usb-storage: unusual_devs entry for Yarvik PMP400 MP4 player
commit
df767b71e5816692134d59c0c17e0f77cd73333d upstream.
This patch (as1553) adds an unusual_dev entrie for the Yarvik PMP400
MP4 music player.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Jesse Feddema <jdfeddema@gmail.com>
Tested-by: Jesse Feddema <jdfeddema@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 7 May 2012 15:20:06 +0000 (11:20 -0400)]
usb-serial: ftdi_sio: fix oops during autosuspend
commit
5cbe61c5aff0a8ada691eb8b07dbfb55c303f640 upstream.
This patch (as1550) fixes a bug in the usb-serial core that affects
the ftdi_sio driver and most likely others as well. The core
implements suspend and resume routines, but it doesn't store pointers
to those routines in the usb_driver structures that it registers,
even though it does set those drivers' supports_autosuspend flag. The
end result is that when one of these devices is autosuspended, we try
to call through a NULL pointer.
The patch fixes the problem by setting the suspend and resume method
pointers to the appropriate routines in the USB serial core, along
with the supports_autosuspend field, in each driver as it is
registered.
This should be back-ported to all the stable kernels that have the new
usb_serial_register_drivers() interface.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Frank Schäfer <schaefer.frank@gmx.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Éric Piel [Mon, 7 May 2012 10:37:54 +0000 (12:37 +0200)]
USB: ftdi-sio: add support for Physik Instrumente E-861
commit
b69cc672052540e8efb1368420f10d7d4d8b8a3d upstream.
This adds VID/PID for the PI E-861. Without it, I had to do:
modprobe -q ftdi-sio product=0x1008 vendor=0x1a72
http://www.physikinstrumente.com/en/products/prdetail.php?sortnr=900610
Signed-off-by: Éric Piel <piel@delmic.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Cox [Mon, 14 May 2012 13:51:22 +0000 (14:51 +0100)]
tty: Allow uart_register/unregister/register
commit
1e66cded334e6cea596c72f6f650eec351b1e959 upstream.
This is legitimate but because we don't clear the drv->state pointer in the
unregister code causes a bogus BUG().
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=42880
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Arnaud Patard [Wed, 25 Apr 2012 10:17:24 +0000 (12:17 +0200)]
8250_pci: fix pch uart matching
commit
aaa10eb1d0034eccc096f583fe308f0921617598 upstream.
The rules used to make 8250_pci "ignore" the PCH uarts are lacking pci subids
entries, preventing it to match and thus is breaking serial port support for
theses systems.
This has been tested on a nanoETXexpress-TT, which has a specifici uart clock.
Tested-by: Erwan Velu <Erwan.Velu@zodiacaerospace.com>
[stable@: please apply to 3.0-stable, 3.2-stable and 3.3-stable]
Signed-off-by: Arnaud Patard <apatard@hupstream.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christian Melki [Mon, 30 Apr 2012 09:21:26 +0000 (11:21 +0200)]
8250.c: less than 2400 baud fix.
commit
f9a9111b540fd67db5dab332f4b83d86c90e27b1 upstream.
We noticed that we were loosing data at speed less than 2400 baud.
It turned out our (TI16750 compatible) uart with 64 byte outgoing fifo
was truncated to 16 byte (bit 5 sets fifo len) when modifying the fcr
reg.
The input code still fills the buffer with 64 bytes if I remember
correctly and thus data is lost.
Our fix was to remove whiping of the fcr content and just add the
TRIGGER_1 which we want for latency.
I can't see why this would not work on less than 2400 always, for all
uarts ...
Otherwise one would have to make sure the filling of the fifo re-checks
the current state of available fifo size (urrk).
Signed-off-by: Christian Melki <christian.melki@ericsson.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lothar Waßmann [Thu, 3 May 2012 09:37:12 +0000 (11:37 +0200)]
Add missing call to uart_update_timeout()
commit
8b979f7c6bf13a57e7b6002f1175312a44773960 upstream.
This patch fixes a problem reported here:
http://article.gmane.org/gmane.linux.ports.arm.kernel/155242/match=auart
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shaohua Li [Sun, 20 May 2012 23:26:59 +0000 (09:26 +1000)]
md: using GFP_NOIO to allocate bio for flush request
commit
b5e1b8cee7ad58a15d2fa79bcd7946acb592602d upstream.
A flush request is usually issued in transaction commit code path, so
using GFP_KERNEL to allocate memory for flush request bio falls into
the classic deadlock issue.
This is suitable for any -stable kernel to which it applies as it
avoids a possible deadlock.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mel Gorman [Wed, 23 May 2012 11:48:13 +0000 (12:48 +0100)]
mm: mempolicy: Let vma_merge and vma_split handle vma->vm_policy linkages
commit
05f144a0d5c2207a0349348127f996e104ad7404 upstream.
Dave Jones' system call fuzz testing tool "trinity" triggered the
following bug error with slab debugging enabled
=============================================================================
BUG numa_policy (Not tainted): Poison overwritten
-----------------------------------------------------------------------------
INFO: 0xffff880146498250-0xffff880146498250. First byte 0x6a instead of 0x6b
INFO: Allocated in mpol_new+0xa3/0x140 age=46310 cpu=6 pid=32154
__slab_alloc+0x3d3/0x445
kmem_cache_alloc+0x29d/0x2b0
mpol_new+0xa3/0x140
sys_mbind+0x142/0x620
system_call_fastpath+0x16/0x1b
INFO: Freed in __mpol_put+0x27/0x30 age=46268 cpu=6 pid=32154
__slab_free+0x2e/0x1de
kmem_cache_free+0x25a/0x260
__mpol_put+0x27/0x30
remove_vma+0x68/0x90
exit_mmap+0x118/0x140
mmput+0x73/0x110
exit_mm+0x108/0x130
do_exit+0x162/0xb90
do_group_exit+0x4f/0xc0
sys_exit_group+0x17/0x20
system_call_fastpath+0x16/0x1b
INFO: Slab 0xffffea0005192600 objects=27 used=27 fp=0x (null) flags=0x20000000004080
INFO: Object 0xffff880146498250 @offset=592 fp=0xffff88014649b9d0
This implied a reference counting bug and the problem happened during
mbind().
mbind() applies a new memory policy to a range and uses mbind_range() to
merge existing VMAs or split them as necessary. In the event of splits,
mpol_dup() will allocate a new struct mempolicy and maintain existing
reference counts whose rules are documented in
Documentation/vm/numa_memory_policy.txt .
The problem occurs with shared memory policies. The vm_op->set_policy
increments the reference count if necessary and split_vma() and
vma_merge() have already handled the existing reference counts.
However, policy_vma() screws it up by replacing an existing
vma->vm_policy with one that potentially has the wrong reference count
leading to a premature free. This patch removes the damage caused by
policy_vma().
With this patch applied Dave's trinity tool runs an mbind test for 5
minutes without error. /proc/slabinfo reported that there are no
numa_policy or shared_policy_node objects allocated after the test
completed and the shared memory region was deleted.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: Dave Jones <davej@redhat.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Stephen Wilson <wilsons@start.ca>
Cc: Christoph Lameter <cl@linux.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tejun Heo [Mon, 14 May 2012 22:04:50 +0000 (15:04 -0700)]
workqueue: skip nr_running sanity check in worker_enter_idle() if trustee is active
commit
544ecf310f0e7f51fa057ac2a295fc1b3b35a9d3 upstream.
worker_enter_idle() has WARN_ON_ONCE() which triggers if nr_running
isn't zero when every worker is idle. This can trigger spuriously
while a cpu is going down due to the way trustee sets %WORKER_ROGUE
and zaps nr_running.
It first sets %WORKER_ROGUE on all workers without updating
nr_running, releases gcwq->lock, schedules, regrabs gcwq->lock and
then zaps nr_running. If the last running worker enters idle
inbetween, it would see stale nr_running which hasn't been zapped yet
and trigger the WARN_ON_ONCE().
Fix it by performing the sanity check iff the trustee is idle.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Wed, 9 May 2012 11:53:23 +0000 (13:53 +0200)]
USB: cdc-wdm: remove from device list on disconnect
commit
6286d85e8efdb59252d1ceb99a56fa6b0b11526c upstream.
Prevents dereferencing an invalid struct usb_interface
pointer.
Always delete entry from device list whether or not the
rest of the device state cleanup is postponed. The device
list uses desc->intf as key, and wdm_open will dereference
this key while searching for a matching device. A device
should not appear in the list unless probe() has succeeded
and disconnect() has not finished.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Wed, 9 May 2012 11:53:22 +0000 (13:53 +0200)]
USB: cdc-wdm: cannot use dev_printk when device is gone
commit
6b0b79d38806481c1c8fffa7c5842f3c83679a42 upstream.
We cannot dereference a removed USB interface for
dev_printk. Use pr_debug instead where necessary.
Flush errors are expected if device is unplugged and are
therefore best ingored at this point.
Move the kill_urbs() call in wdm_release with dev_dbg()
for the non disconnect, as we know it has already been
called if WDM_DISCONNECTING is set. This does not
actually fix anything, but keeps the code more consistent.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjørn Mork [Wed, 9 May 2012 11:53:21 +0000 (13:53 +0200)]
USB: cdc-wdm: poll must return POLLHUP if device is gone
commit
616b6937e348ef2b4c6ea5fef2cd3c441145efb0 upstream.
Else the poll will be restarted indefinitely in a tight loop,
preventing final device cleanup.
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Fri, 27 Apr 2012 12:36:37 +0000 (14:36 +0200)]
USB: cdc-wdm: fix memory leak
commit
2f338c8a1904e2e7aa5a8bd12fb0cf2422d17da4 upstream.
cleanup() is not called if the last close() comes after
disconnect(). That leads to a memory leak. Rectified
by checking for an earlier disconnect() in release()
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Fri, 27 Apr 2012 12:23:54 +0000 (14:23 +0200)]
USB: cdc-wdm: sanitize error returns
commit
24a85bae5da2b43fed423859c09c5a81ab359473 upstream.
wdm_flush() returns unsanitized USB error codes.
They must be cleaned up to before being anded to user space
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Kees Cook [Thu, 19 Apr 2012 06:16:45 +0000 (23:16 -0700)]
docs: update HOWTO for 2.6.x -> 3.x versioning
commit
591bfc6bf9e5e25e464fd4c87d64afd5135667c4 upstream.
The HOWTO document needed updating for the new kernel versioning. The
git URI for -next was updated as well.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Anton Vorontsov [Sat, 12 May 2012 00:17:17 +0000 (17:17 -0700)]
persistent_ram: Fix buffer size clamping during writes
commit
484dd30e016eb425b0de871357fff2c9bb93be45 upstream.
This is a longstanding bug, almost unnoticeable when calling
persistent_ram_write() for small buffers.
But when called for large data buffers, the write routine behaves
incorrectly, as the size may never update: instead of clamping
the size to the maximum buffer size, buffer_size_add_clamp() returns
an error (which is never checked by the write routine, btw).
To fix this, we now use buffer_size_add() that actually clamps the
size to the max value.
Also remove buffer_size_add_clamp(), it is no longer needed.
Signed-off-by: Anton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Weinberger [Sat, 14 Apr 2012 15:29:30 +0000 (17:29 +0200)]
um: Implement a custom pte_same() function
commit
f15b9000eb1d09bbaa4b0a6b2089d7e1f64e84b3 upstream.
UML uses the _PAGE_NEWPAGE flag to mark pages which are not jet
installed on the host side using mmap().
pte_same() has to ignore this flag, otherwise unuse_pte_range()
is unable to unuse the page because two identical
page tables entries with different _PAGE_NEWPAGE flags would not
match and swapoff() would never return.
Analyzed-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Richard Weinberger [Sat, 14 Apr 2012 15:46:01 +0000 (17:46 +0200)]
um: Fix __swp_type()
commit
2b76ebaa728f8a3967c52aa189261c72fe56a6f1 upstream.
The current __swp_type() function uses a too small bitshift.
Using more than one swap files causes bad pages because
the type bits clash with other page flags.
Analyzed-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Jonathan Nieder [Fri, 11 May 2012 14:17:16 +0000 (16:17 +0200)]
HID: logitech: read all 32 bits of report type bitfield
commit
44d27f7dfedd9aadc082cda31462f6600f56e4ec upstream.
On big-endian systems (e.g., Apple PowerBook), trying to use a
logitech wireless mouse with the Logitech Unifying Receiver does not
work with v3.2 and later kernels. The device doesn't show up in
/dev/input. Older kernels work fine.
That is because the new hid-logitech-dj driver claims the device. The
device arrival notification appears:
20 00 41 02 00 00 00 00 00 00 00 00 00 00 00
and we read the report_types bitfield (02 00 00 00) to find out what
kind of device it is. Unfortunately the driver only reads the first 8
bits and treats that value as a 32-bit little-endian number, so on a
powerpc the report type seems to be 0x02000000 and is not recognized.
Even on little-endian machines, connecting a media center remote
control (report type 00 01 00 00) with this driver loaded would
presumably fail for the same reason.
Fix both problems by using get_unaligned_le32() to read all four
bytes, which is a little clearer anyway. After this change, the
wireless mouse works on Hugo's PowerBook again.
Based on a patch by Nestor Lopez Casado.
Addresses http://bugs.debian.org/671292
Reported-by: Hugo Osvaldo Barrera <hugo@osvaldobarrera.com.ar>
Inspired-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Nestor Lopez Casado <nlopezcasad@logitech.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oliver Neukum [Mon, 30 Apr 2012 07:13:46 +0000 (09:13 +0200)]
usbhid: prevent deadlock during timeout
commit
8815bb09af21316aeb5f8948b24ac62181670db2 upstream.
On some HCDs usb_unlink_urb() can directly call the
completion handler. That limits the spinlocks that can
be taken in the handler to locks not held while calling
usb_unlink_urb()
To prevent a race with resubmission, this patch exposes
usbcore's infrastructure for blocking submission, uses it
and so drops the lock without causing a race in usbhid.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Herrmann [Tue, 8 May 2012 14:52:31 +0000 (16:52 +0200)]
HID: wiimote: Fix IR data parser
commit
74b89e8a3625c17c7452532dfb997ac4f1a38751 upstream.
We incorrectly parse incoming IR data. The extra byte contains the upper
bits and not the lower bits of the x/y coordinates. User-space expects
absolute position data from us so this patch does not break existing
applications. On the contrary, it extends the virtual view and fixes
garbage reports for margin areas of the virtual screen.
Reported-by: Peter Bukovsky <bukovsky.peter@gmail.com>
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Robert Richter [Fri, 18 May 2012 10:40:42 +0000 (12:40 +0200)]
perf/x86: Update event scheduling constraints for AMD family 15h models
commit
5bcdf5e4fee3c45e1281c25e4941f2163cb28c65 upstream.
This update is for newer family 15h cpu models from 0x02 to 0x1f.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1337337642-1621-1-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Julia Lawall [Sun, 22 Apr 2012 11:37:09 +0000 (13:37 +0200)]
drivers/staging/comedi/comedi_fops.c: add missing vfree
commit
abae41e6438b798e046d721b6ccdd55b4a398170 upstream.
aux_free is freed on all other exits from the function. By removing the
return, we can benefit from the vfree already at the end of the function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Yishai Hadas [Thu, 10 May 2012 20:28:05 +0000 (23:28 +0300)]
IB/core: Fix mismatch between locked and pinned pages
commit
c4870eb874ac16dccef40e1bc7a002c7e9156adc upstream.
Commit
bc3e53f682d9 ("mm: distinguish between mlocked and pinned
pages") introduced a separate counter for pinned pages and used it in
the IB stack. However, in ib_umem_get() the pinned counter is
incremented, but ib_umem_release() wrongly decrements the locked
counter. Fix this.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reviewed-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Laurent Pinchart [Fri, 18 May 2012 08:58:26 +0000 (10:58 +0200)]
fbdev: sh_mobile_lcdc: Don't confuse line size with pitch
commit
72c04af9a2d57b7945cf3de8e71461bd80695d50 upstream.
When using the MERAM the LCDC line size needs to be programmed with a
MERAM-specific value different than the real frame buffer pitch. Fix it.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Eric Paris [Wed, 4 Apr 2012 17:47:11 +0000 (13:47 -0400)]
SELinux: if sel_make_bools errors don't leave inconsistent state
commit
154c50ca4eb9ae472f50b6a481213e21ead4457d upstream.
We reset the bool names and values array to NULL, but do not reset the
number of entries in these arrays to 0. If we error out and then get back
into this function we will walk these NULL pointers based on the belief
that they are non-zero length.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
David Howells [Fri, 11 May 2012 09:56:56 +0000 (10:56 +0100)]
KEYS: Use the compat keyctl() syscall wrapper on Sparc64 for Sparc32 compat
commit
45de6767dc51358a188f75dc4ad9dfddb7fb9480 upstream.
Use the 32-bit compat keyctl() syscall wrapper on Sparc64 for Sparc32 binary
compatibility.
Without this, keyctl(KEYCTL_INSTANTIATE_IOV) is liable to malfunction as it
uses an iovec array read from userspace - though the kernel should survive this
as it checks pointers and sizes anyway.
I think all the other keyctl() function should just work, provided (a) the top
32-bits of each 64-bit argument register are cleared prior to invoking the
syscall routine, and the 32-bit address space is right at the 0-end of the
64-bit address space. Most of the arguments are 32-bit anyway, and so for
those clearing is not required.
Signed-off-by: David Howells <dhowells@redhat.com
cc: "David S. Miller" <davem@davemloft.net>
cc: sparclinux@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thomas Gleixner [Mon, 7 May 2012 17:59:47 +0000 (17:59 +0000)]
powerpc: Fix broken cpu_idle_wait() implementation
commit
9cd75e13de2dcf32ecc21c7f277cff3c0ced059e upstream.
commit
771dae818 (powerpc/cpuidle: Add cpu_idle_wait() to allow
switching of idle routines) implemented cpu_idle_wait() for powerpc.
The changelog says:
"The equivalent routine for x86 is in arch/x86/kernel/process.c
but the powerpc implementation is different.":
Unfortunately the changelog is completely useless as it does not tell
_WHY_ it is different.
Aside of being different the implementation is patently wrong.
The rescheduling IPI is async. That means that there is no guarantee,
that the other cores have executed the IPI when cpu_idle_wait()
returns. But that's the whole purpose of this function: to guarantee
that no CPU uses the old idle handler anymore.
Use the smp_functional_call() based implementation, which fulfils the
requirements.
[ This code is going to replaced by a core version to remove all the
pointless copies in arch/*, but this one should go to stable ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Cc: Trinabh Gupta <g.trinabh@gmail.com>
Cc: Arun R Bharadwaj <arun.r.bharadwaj@gmail.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Link: http://lkml.kernel.org/r/20120507175651.980164748@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve Wise [Mon, 30 Apr 2012 20:31:29 +0000 (15:31 -0500)]
RDMA/cxgb4: Drop peer_abort when no endpoint found
commit
14b9222808bb8bfefc71f72bc0dbdcf3b2f0140f upstream.
Log a warning and drop the abort message. Otherwise we will do a
bogus wake_up() and crash.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve Wise [Fri, 27 Apr 2012 15:24:33 +0000 (10:24 -0500)]
RDMA/cxgb4: Use dst parameter in import_ep()
commit
bd61baaf59669accae2720799394a51fecabe5d9 upstream.
Function import_ep() is incorrectly using ep->dst instead of the dst
ptr passed in. This causes a crash when accepting new rdma connections
becase ep->dst is not initialized yet.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Steve Wise [Fri, 27 Apr 2012 14:59:16 +0000 (09:59 -0500)]
RDMA/cxgb4: Always wake up waiters in c4iw_peer_abort_intr()
commit
0f1dcfae6bc5563424346ad3a03282b8235a4c33 upstream.
This fixes a race where an ingress abort fails to wake up the thread
blocked in rdma_init() causing the app to hang.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dan Williams [Mon, 30 Apr 2012 18:57:44 +0000 (11:57 -0700)]
isci: fix oem parameter validation on single controller skus
commit
fc25f79af321c01a739150ba2c09435cf977a63d upstream.
OEM parameters [1] are parsed from the platform option-rom / efi
driver. By default the driver was validating the parameters for the
dual-controller case, but in single-controller case only the first set
of parameters may be valid.
Limit the validation to the number of actual controllers detected
otherwise the driver may fail to parse the valid parameters leading to
driver-load or runtime failures.
[1] the platform specific set of phy address, configuration,and analog
tuning values
Reported-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
nagalakshmi.nandigama@lsi.com [Tue, 20 Mar 2012 06:40:01 +0000 (12:10 +0530)]
SCSI: mpt2sas: Fix for panic happening because of improper memory allocation
commit
e42fafc25fa86c61824e8d4c5e7582316415d24f upstream.
The ioc->pfacts member in the IOC structure is getting set to zero
following a call to _base_get_ioc_facts due to the memset in that routine.
So if the ioc->pfacts was read after a host reset, there would be a NULL
pointer dereference. The routine _base_get_ioc_facts is called from context
of host reset. The problem in _base_get_ioc_facts is the size of
Mpi2IOCFactsReply is 64, whereas the sizeof "struct mpt2sas_facts" is 60,
so there is a four byte overflow resulting from the memset.
Also, there is memset in _base_get_port_facts using the incorrect structure,
it should be "struct mpt2sas_port_facts" instead of Mpi2PortFactsReply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heiko Carstens [Wed, 9 May 2012 07:37:30 +0000 (09:37 +0200)]
s390/pfault: fix task state race
commit
d5e50a51ccbda36b379aba9d1131a852eb908dda upstream.
When setting the current task state to TASK_UNINTERRUPTIBLE this can
race with a different cpu. The other cpu could set the task state after
it inspected it (while it was still TASK_RUNNING) to TASK_RUNNING which
would change the state from TASK_UNINTERRUPTIBLE to TASK_RUNNING again.
This race was always present in the pfault interrupt code but didn't
cause anything harmful before commit
f2db2e6c "[S390] pfault: cpu hotplug
vs missing completion interrupts" which relied on the fact that after
setting the task state to TASK_UNINTERRUPTIBLE the task would really
sleep.
Since this is not necessarily the case the result may be a list corruption
of the pfault_list or, as observed, a use-after-free bug while trying to
access the task_struct of a task which terminated itself already.
To fix this, we need to get a reference of the affected task when receiving
the initial pfault interrupt and add special handling if we receive yet
another initial pfault interrupt when the task is already enqueued in the
pfault list.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 21 May 2012 19:52:42 +0000 (12:52 -0700)]
Fix blocking allocations called very early during bootup
commit
31a67102f4762df5544bc2dfb34a931233d2a5b2 upstream.
During early boot, when the scheduler hasn't really been fully set up,
we really can't do blocking allocations because with certain (dubious)
configurations the "might_resched()" calls can actually result in
scheduling events.
We could just make such users always use GFP_ATOMIC, but quite often the
code that does the allocation isn't really aware of the fact that the
scheduler isn't up yet, and forcing that kind of random knowledge on the
initialization code is just annoying and not good for anybody.
And we actually have a the 'gfp_allowed_mask' exactly for this reason:
it's just that the kernel init sequence happens to set it to allow
blocking allocations much too early.
So move the 'gfp_allowed_mask' initialization from 'start_kernel()'
(which is some of the earliest init code, and runs with preemption
disabled for good reasons) into 'kernel_init()'. kernel_init() is run
in the newly created thread that will become the 'init' process, as
opposed to the early startup code that runs within the context of what
will be the first idle thread.
So by the time we reach 'kernel_init()', we know that the scheduler must
be at least limping along, because we've already scheduled from the idle
thread into the init thread.
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mark Brown [Sun, 13 May 2012 17:35:56 +0000 (18:35 +0100)]
regulator: core: Release regulator-regulator supplies on error
commit
e81dba85c6388dfabcb76cbc2b8bd02836a53ae5 upstream.
If we fail while registering a regulator make sure we release the supply
for the regulator if there is one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Luis R. Rodriguez [Fri, 23 Mar 2012 14:23:31 +0000 (07:23 -0700)]
cfg80211: warn if db.txt is empty with CONFIG_CFG80211_INTERNAL_REGDB
commit
80007efeff0568375b08faf93c7aad65602cb97e upstream.
It has happened twice now where elaborate troubleshooting has
undergone on systems where CONFIG_CFG80211_INTERNAL_REGDB [0]
has been set but yet net/wireless/db.txt was not updated.
Despite the documentation on this it seems system integrators could
use some more help with this, so throw out a kernel warning at boot time
when their database is empty.
This does mean that the error-prone system integrator won't likely
realize the issue until they boot the machine but -- it does not seem
to make sense to enable a build bug breaking random build testing.
[0] http://wireless.kernel.org/en/developers/Regulatory/CRDA#CONFIG_CFG80211_INTERNAL_REGDB
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Youngsin Lee <youngsin@qualcomm.com>
Cc: Raja Mani <rmani@qca.qualcomm.com>
Cc: Senthil Kumar Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Vipin Mehta <vipimeht@qca.qualcomm.com>
Cc: yahuan@qca.qualcomm.com
Cc: jjan@qca.qualcomm.com
Cc: vthiagar@qca.qualcomm.com
Cc: henrykim@qualcomm.com
Cc: jouni@qca.qualcomm.com
Cc: athiruve@qca.qualcomm.com
Cc: cjkim@qualcomm.com
Cc: philipk@qca.qualcomm.com
Cc: sunnykim@qualcomm.com
Cc: sskwak@qualcomm.com
Cc: kkim@qualcomm.com
Cc: mattbyun@qualcomm.com
Cc: ryanlee@qualcomm.com
Cc: simbap@qualcomm.com
Cc: krislee@qualcomm.com
Cc: conner@qualcomm.com
Cc: hojinkim@qualcomm.com
Cc: honglee@qualcomm.com
Cc: johnwkim@qualcomm.com
Cc: jinyong@qca.qualcomm.com
Signed-off-by: Luis R. Rodriguez <mcgrof@frijolero.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Mon, 21 May 2012 23:06:20 +0000 (16:06 -0700)]
vfs: make AIO use the proper rw_verify_area() area helpers
commit
a70b52ec1aaeaf60f4739edb1b422827cb6f3893 upstream.
We had for some reason overlooked the AIO interface, and it didn't use
the proper rw_verify_area() helper function that checks (for example)
mandatory locking on the file, and that the size of the access doesn't
cause us to overflow the provided offset limits etc.
Instead, AIO did just the security_file_permission() thing (that
rw_verify_area() also does) directly.
This fixes it to do all the proper helper functions, which not only
means that now mandatory file locking works with AIO too, we can
actually remove lines of code.
Reported-by: Manish Honap <manish_honap_vit@yahoo.co.in>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tilman Schmidt [Wed, 25 Apr 2012 13:02:20 +0000 (13:02 +0000)]
isdn/gigaset: improve error handling querying firmware version
commit
e055d03dc088a990fe5ea24a2d64033a168da23c upstream.
An out-of-place "OK" response to the "AT+GMR" (get firmware version)
command turns out to be, more often than not, a delayed response to
a previous command rather than an actual error, so continue waiting
for the version number in that case.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tilman Schmidt [Wed, 25 Apr 2012 13:02:20 +0000 (13:02 +0000)]
isdn/gigaset: fix CAPI disconnect B3 handling
commit
62a1cfe052346b96a552b6a9178d412c709711bb upstream.
If DISCONNECT_B3_IND was synthesized because of a DISCONNECT_REQ
with existing logical connections, the connection state wasn't
updated accordingly. Also the emitted DISCONNECT_B3_IND message
wasn't included in the debug log as requested.
This patch fixes both of these issues.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tilman Schmidt [Wed, 25 Apr 2012 13:02:19 +0000 (13:02 +0000)]
isdn/gigaset: ratelimit CAPI message dumps
commit
8e618aad5348b6e6c5a90e8d97ea643197963b20 upstream.
Introduce a global ratelimit for CAPI message dumps to protect
against possible log flood.
Drop the ratelimit for ignored messages which is now covered by the
global one.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 20 May 2012 22:29:13 +0000 (15:29 -0700)]
Linux 3.4
Linus Torvalds [Sat, 19 May 2012 22:30:15 +0000 (15:30 -0700)]
Merge tag 'parisc-fixes' of git://git./linux/kernel/git/jejb/parisc-2.6
Pull PA-RISC fixes from James Bottomley:
"This is a set of three bug fixes that gets parisc running again on
systems with PA1.1 processors.
Two fix regressions introduced in 2.6.39 and one fixes a prefetch bug
that only affects PA7300LC processors. We also have another pending
fix to do with the sectional arrangement of vmlinux.lds, but there's a
query on it during testing on one particular system type, so I'll hold
off sending it in for now."
* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
[PARISC] fix panic on prefetch(NULL) on PA7300LC
[PARISC] fix crash in flush_icache_page_asm on PA1.1
[PARISC] fix PA1.1 oops on boot