usb: quirks: Add delay-init quirk for Corsair K70 LUX RGB

commit a77112577667cbda7c6292c52d909636aef31fd9 upstream.

Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 LUX RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.

Dmesg output:
usb 1-6: string descriptor 0 read error: -110
usb 1-6: New USB device found, idVendor=1b1c, idProduct=1b33
usb 1-6: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-6: can't set config #1, error -110

Signed-off-by: Emmanuel Pescosta <emmanuelpescosta099@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: Wait for extra delay time after USB_PORT_FEAT_RESET for quirky hub

commit 781f0766cc41a9dd2e5d118ef4b1d5d89430257b upstream.

Devices connected under Terminus Technology Inc. Hub (1a40:0101) may
fail to work after the system resumes from suspend:
[  206.063325] usb 3-2.4: reset full-speed USB device number 4 using xhci_hcd
[  206.143691] usb 3-2.4: device descriptor read/64, error -32
[  206.351671] usb 3-2.4: device descriptor read/64, error -32

Info for this hub:
T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=480 MxCh= 4
D:  Ver= 2.00 Cls=09(hub  ) Sub=00 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=1a40 ProdID=0101 Rev=01.11
S:  Product=USB 2.0 Hub
C:  #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub

Some expirements indicate that the USB devices connected to the hub are
innocent, it's the hub itself is to blame. The hub needs extra delay
time after it resets its port.

Hence wait for extra delay, if the device is connected to this quirky
hub.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: quirks: Add no-lpm quirk for Raydium touchscreens

commit deefd24228a172d1b27d4a9adbfd2cdacd60ae64 upstream.

Raydium USB touchscreen fails to set config if LPM is enabled:
[    2.030658] usb 1-8: New USB device found, idVendor=2386, idProduct=3119
[    2.030659] usb 1-8: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.030660] usb 1-8: Product: Raydium Touch System
[    2.030661] usb 1-8: Manufacturer: Raydium Corporation
[    7.132209] usb 1-8: can't set config #1, error -110

Same behavior can be observed on 2386:3114.

Raydium claims the touchscreen supports LPM under Windows, so I used
Microsoft USB Test Tools (MUTT) [1] to check its LPM status. MUTT shows
that the LPM doesn't work under Windows, either. So let's just disable LPM
for Raydium touchscreens.

[1] https://docs.microsoft.com/en-us/windows-hardware/drivers/usbcon/usb-test-tools

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdc-acm: add entry for Hiro (Conexant) modem

commit 63529eaa6164ef7ab4b907b25ac3648177e5e78f upstream.

The cdc-acm kernel module currently does not support the Hiro (Conexant)
H05228 USB modem. The patch below adds the device specific information:
idVendor 0x0572
idProduct 0x1349

Signed-off-by: Maarten Jacobs <maarten256@outlook.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: Fix potential uninitialized variable use

commit 95217260649aa504eb5d4a0d50959ca4e67c8f96 upstream.

If alloc_can_err_skb() fails, cf is never initialized.
Move assignment of cf inside check.

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: kvaser_usb: Fix accessing freed memory in kvaser_usb_start_xmit()

commit e13fb9b37cc00616b90df2d620f30345b5ada6ff upstream.

The call to can_put_echo_skb() may result in the skb being freed. The skb
is later used in the call to dev->ops->dev_frame_to_cmd().

This is avoided by moving the call to can_put_echo_skb() after
dev->ops->dev_frame_to_cmd().

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jimmy Assarsson <jimmyassarsson@gmail.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/ca0132 - Call pci_iounmap() instead of iounmap()

commit d99501b8575dc1248bacf1b58d2241cb4b265d49 upstream.

We need to call pci_iounmap() instead of iounmap() for the regions
obtained via pci_iomap() call for some archs that need special
treatment.

Fixes: aa31704fd81c ("ALSA: hda/ca0132: Add PCI region2 iomap for SBZ")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek - Add quirk entry for HP Pavilion 15

commit 563785edfcef02b566e64fb5292c74c1600808aa upstream.

HP Pavilion 15 (103c:820d) with ALC295 codec requires the quirk for
the mute LED control over mic3 pin.  Added the corresponding quirk
entry.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=201653
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

uio: Fix an Oops on load

commit 432798195bbce1f8cd33d1c0284d0538835e25fb upstream.

I was trying to solve a double free but I introduced a more serious
NULL dereference bug.  The problem is that if there is an IRQ which
triggers immediately, then we need "info->uio_dev" but it's not set yet.

This patch puts the original initialization back to how it was and just
sets info->uio_dev to NULL on the error path so it should solve both
the Oops and the double free.

Fixes: f019f07ecf6a ("uio: potential double frees if __uio_register_device() fails")
Reported-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Tested-by: Mathias Thore <Mathias.Thore@infinera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RISC-V: Fix raw_copy_{to,from}_user()

commit 21f70d4abf9e17c2e3d7e64b7bfa3424e017f176 upstream.

Sparse highlighted it, and appears to be a pure bug (from vs to).

./arch/riscv/include/asm/uaccess.h:403:35: warning: incorrect type in argument 1 (different address spaces)
./arch/riscv/include/asm/uaccess.h:403:39: warning: incorrect type in argument 2 (different address spaces)
./arch/riscv/include/asm/uaccess.h:409:37: warning: incorrect type in argument 1 (different address spaces)
./arch/riscv/include/asm/uaccess.h:409:41: warning: incorrect type in argument 2 (different address spaces)

Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: OCTEON: cavium_octeon_defconfig: re-enable OCTEON USB driver

commit 82fba2df7f7c019627f24c5036dc99f41731d770 upstream.

Re-enable OCTEON USB driver which is needed on older hardware
(e.g. EdgeRouter Lite) for mass storage etc. This got accidentally
deleted when config options were changed for OCTEON2/3 USB.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: f922bc0ad08b ("MIPS: Octeon: cavium_octeon_defconfig: Enable more drivers")
Patchwork: https://patchwork.linux-mips.org/patch/21077/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

media: v4l: event: Add subscription to list before calling "add" operation

commit 92539d3eda2c090b382699bbb896d4b54e9bdece upstream.

Patch ad608fbcf166 changed how events were subscribed to address an issue
elsewhere. As a side effect of that change, the "add" callback was called
before the event subscription was added to the list of subscribed events,
causing the first event queued by the add callback (and possibly other
events arriving soon afterwards) to be lost.

Fix this by adding the subscription to the list before calling the "add"
callback, and clean up afterwards if that fails.

Fixes: ad608fbcf166 ("media: v4l: event: Prevent freeing event subscriptions while accessed")

Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Dave Stevenson <dave.stevenson@raspberrypi.org>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org (for 4.14 and up)
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/ldt: Remove unused variable in map_ldt_struct()

commit b082f2dd80612015cd6d9d84e52099734ec9a0e1 upstream

Splitting out the sanity check in map_ldt_struct() moved page table syncing
into a separate function, which made the pgd variable unused. Remove it.

[ tglx: Massaged changelog ]

Fixes: 9bae3197e15d ("x86/ldt: Split out sanity check in map_ldt_struct()")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-4-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/ldt: Unmap PTEs for the slot before freeing LDT pages

commit a0e6e0831c516860fc7f9be1db6c081fe902ebcf upstream

modify_ldt(2) leaves the old LDT mapped after switching over to the new
one. The old LDT gets freed and the pages can be re-used.

Leaving the mapping in place can have security implications. The mapping is
present in the userspace page tables and Meltdown-like attacks can read
these freed and possibly reused pages.

It's relatively simple to fix: unmap the old LDT and flush TLB before
freeing the old LDT memory.

This further allows to avoid flushing the TLB in map_ldt_struct() as the
slot is unmapped and flushed by unmap_ldt_struct() or has never been mapped
at all.

[ tglx: Massaged changelog and removed the needless line breaks ]

Fixes: f55f0501cbf6 ("x86/pti: Put the LDT in its own PGD if PTI is on")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: luto@kernel.org
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-3-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/mm: Move LDT remap out of KASLR region on 5-level paging

commit d52888aa2753e3063a9d3a0c9f72f94aa9809c15 upstream

On 5-level paging the LDT remap area is placed in the middle of the KASLR
randomization region and it can overlap with the direct mapping, the
vmalloc or the vmap area.

The LDT mapping is per mm, so it cannot be moved into the P4D page table
next to the CPU_ENTRY_AREA without complicating PGD table allocation for
5-level paging.

The 4 PGD slot gap just before the direct mapping is reserved for
hypervisors, so it cannot be used.

Move the direct mapping one slot deeper and use the resulting gap for the
LDT remap area. The resulting layout is the same for 4 and 5 level paging.

[ tglx: Massaged changelog ]

Fixes: f55f0501cbf6 ("x86/pti: Put the LDT in its own PGD if PTI is on")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Lutomirski <luto@kernel.org>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: dave.hansen@linux.intel.com
Cc: peterz@infradead.org
Cc: boris.ostrovsky@oracle.com
Cc: jgross@suse.com
Cc: bhe@redhat.com
Cc: willy@infradead.org
Cc: linux-mm@kvack.org
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181026122856.66224-2-kirill.shutemov@linux.intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

SUNRPC: drop pointless static qualifier in xdr_get_next_encode_buffer()

[ Upstream commit 025911a5f4e36955498ed50806ad1b02f0f76288 ]

There is no need to have the '__be32 *p' variable static since new value
always be assigned before use it.

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "scripts/setlocalversion: git: Make -dirty check more robust"

[ Upstream commit 8ef14c2c41d962756d314f1d7dc972b0ea7a180f ]

This reverts commit 6147b1cf19651c7de297e69108b141fb30aa2349.

The reverted patch results in attempted write access to the source
repository, even if that repository is mounted read-only.

Output from "strace git status -uno --porcelain":

getcwd("/tmp/linux-test", 129)          = 16
open("/tmp/linux-test/.git/index.lock", O_RDWR|O_CREAT|O_EXCL|O_CLOEXEC, 0666) =
-1 EROFS (Read-only file system)

While git appears to be able to handle this situation, a monitored
build environment (such as the one used for Chrome OS kernel builds)
may detect it and bail out with an access violation error. On top of
that, the attempted write access suggests that git _will_ write to the
file even if a build output directory is specified. Users may have the
reasonable expectation that the source repository remains untouched in
that situation.

Fixes: 6147b1cf19651 ("scripts/setlocalversion: git: Make -dirty check more robust"
Cc: Genki Sky <sky@genki.is>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

kbuild: deb-pkg: fix too low build version number

[ Upstream commit bbcde0a7241261cd0ca8d8e6b94a4113a4b71443 ]

Since commit b41d920acff8 ("kbuild: deb-pkg: split generating packaging
and build"), the build version of the kernel contained in a deb package
is too low by 1.

Prior to the bad commit, the kernel was built first, then the number
in .version file was read out, and written into the debian control file.

Now, the debian control file is created before the kernel is actually
compiled, which is causing the version number mismatch.

Let the mkdebian script pass KBUILD_BUILD_VERSION=${revision} to require
the build system to use the specified version number.

Fixes: b41d920acff8 ("kbuild: deb-pkg: split generating packaging and build")
Reported-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Doug Smythies <dsmythies@telus.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: aquantia: invalid checksumm offload implementation

[ Upstream commit ad703c2b9127f9acdef697ec4755f6da4beaa266 ]

Packets with marked invalid IP/UDP/TCP checksums were considered as good
by the driver. The error was in a logic, processing offload bits in
RX descriptor.

Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: aquantia: fixed enable unicast on 32 macvlan

[ Upstream commit bfaa9f8553d5c20703781e63f4fc8cb4792f18fd ]

Fixed a condition mistake due to which macvlans unicast
item number 32 was not added in the unicast filter.

The consequence is that when exactly 32 macvlans are created
on NIC, the last created macvlan receives no traffic because
its MAC was not registered in HW.

Fixes: 94b3b542303f ("net: aquantia: vlan unicast address list correct handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Tested-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: aquantia: fix potential IOMMU fault after driver unbind

[ Upstream commit 7a1bb49461b12b2e6332a4d054256835f45203f3 ]

IOMMU fault may occurr on unbind/bind or if_down/if_up sequence.

Although driver disables the rings on down, this is not enough.
Due to internal HW design, during subsequent initialization
NIC sometimes may reuse RX descriptors cache and write to the
host memory from the descriptor cache.
That's get catched by IOMMU on host.

This patch invalidates the descriptor cache in NIC on interface down
to prevent writing to the cached descriptors and to the memory pointed
in those descriptors.

Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: stmmac: Fix RX packet size > 8191

[ Upstream commit 8137b6ef0ce469154e5cf19f8e7fe04d9a72ac5e ]

Ping problems with packets > 8191 as shown:

PING 192.168.1.99 (192.168.1.99) 8150(8178) bytes of data.
8158 bytes from 192.168.1.99: icmp_seq=1 ttl=64 time=0.669 ms
wrong data byte 8144 should be 0xd0 but was 0x0
16    10 11 12 13 14 15 16 17 18 19 1a 1b 1c 1d 1e 1f
      20 21 22 23 24 25 26 27 28 29 2a 2b 2c 2d 2e 2f
%< ---------------snip--------------------------------------
8112  b0 b1 b2 b3 b4 b5 b6 b7 b8 b9 ba bb bc bd be bf
      c0 c1 c2 c3 c4 c5 c6 c7 c8 c9 ca cb cc cd ce cf
8144  0 0 0 0 d0 d1
      ^^^^^^^
Notice the 4 bytes of 0 before the expected byte of d0.

Databook notes that the RX buffer must be a multiple of 4/8/16
bytes [1].

Update the DMA Buffer size define to 8188 instead of 8192. Remove
the -1 from the RX buffer size allocations and use the new
DMA Buffer size directly.

[1] Synopsys DesignWare Cores Ethernet MAC Universal v3.70a
    [section 8.4.2 - Table 8-24]

Tested on SoCFPGA Stratix10 with ping sweep from 100 to 8300 byte packets.

Fixes: 286a83721720 ("stmmac: add CHAINED descriptor mode support (V4)")
Suggested-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qed: Fix potential memory corruption

[ Upstream commit fa5c448d98f0df660bfcad3dd5facc027ef84cd3 ]

A stuck ramrod should be deleted from the completion_pending list,
otherwise it will be added again in the future and corrupt the list.

Return error value to inform that ramrod is stuck and should be deleted.

Signed-off-by: Sagiv Ozeri <sagiv.ozeri@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qed: Fix SPQ entries not returned to pool in error flows

[ Upstream commit fb5e7438e7a3c8966e04ccb0760170e9e06f3699 ]

qed_sp_destroy_request() API was added for SPQ users that need to
free/return the entry they acquired in their error flows.

Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qed: Fix blocking/unlimited SPQ entries leak

[ Upstream commit 2632f22ebd08da249c2017962a199a0cfb2324bf ]

When there are no SPQ entries left in the free_pool, new entries are
allocated and are added to the unlimited list. When an entry in the pool
is available, the content is copied from the original entry, and the new
entry is sent to the device. qed_spq_post() is not aware of that, so the
additional entry is stored in the original entry as p_post_ent, which can
later be returned to the pool.

Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

qed: Fix memory/entry leak in qed_init_sp_request()

[ Upstream commit 39477551df940ddb1339203817de04f5caaacf7a ]

Free the allocated SPQ entry or return the acquired SPQ entry to the free
list in error flows.

Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i40e: restore NETIF_F_GSO_IPXIP[46] to netdev features

[ Upstream commit ba766b8b99c30ad3c55ed8cf224d1185ecff1476 ]

Since commit bacd75cfac8a ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.

Fix this by adding back the missing feature flags.

For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa4a
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.

NETIF_F_GSO_IPXIP6 was added in commit bf2d1df39502 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Change req_speeds to be u16

[ Upstream commit ffe498237b36ee42624e139b21efa05da4ff1f48 ]

Since the req_speeds field in struct ice_link_status is a u8,
req_speeds & ICE_AQ_LINK_SPEED_40GB always returns 0. This was caught
by a coverity scan.

Fix this by changing req_speeds to be u16.

Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Fix the bytecount sent to netdev_tx_sent_queue

[ Upstream commit d944b46992f8e99b6bdc721e44b02e5ca294fa2b ]

Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.

Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Fix dead device link issue with flow control

[ Upstream commit 0f5d4c21a50716f8bd4e220544b82dca7408d113 ]

Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.

Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Do not zero sample_id_all for group members

[ Upstream commit 8e88c29b351ed4e09dd63f825f1c8260b0cb0ab3 ]

Andi reported following malfunction:

  # perf record -e '{ref-cycles,cycles}:S' -a sleep 1
  # perf script
  non matching sample_id_all

That's because we disable sample_id_all bit for non-sampling group
members. We can't do that, because it needs to be the same over the
whole event list. This patch keeps it untouched again.

Reported-by: Andi Kleen <andi@firstfloor.org>
Tested-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180923150420.27327-1-jolsa@kernel.org
Fixes: e9add8bac6c6 ("perf evsel: Disable write_backward for leader sampling group events")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf tools: Fix undefined symbol scnprintf in libperf-jvmti.so

[ Upstream commit 6ac2226229d931153331a93d90655a3de05b9290 ]

Currently jvmti agent can not be used because function scnprintf is not
present in the agent libperf-jvmti.so. As a result the JVM when using
such agent to record JITed code profiling information will fail on
looking up scnprintf:

  java: symbol lookup error: lib/libperf-jvmti.so: undefined symbol: scnprintf

This commit fixes that by reverting to the use of snprintf, that can be
looked up, instead of scnprintf, adding a proper check for the returned
value in order to print a better error message when the jitdump file
pathname is too long. Checking the returned value also helps to comply
with some recent gcc versions, like gcc8, which will fail due to
truncated writing checks related to the -Werror=format-truncation= flag.

Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
LPU-Reference: 1541117601-18937-2-git-send-email-gromero@linux.vnet.ibm.com
Link: https://lkml.kernel.org/n/tip-mvpxxxy7wnzaj74cq75muw3f@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

sched/core: Take the hotplug lock in sched_init_smp()

[ Upstream commit 40fa3780bac2b654edf23f6b13f4e2dd550aea10 ]

When running on linux-next (8c60c36d0b8c ("Add linux-next specific files
for 20181019")) + CONFIG_PROVE_LOCKING=y on a big.LITTLE system (e.g.
Juno or HiKey960), we get the following report:

 [    0.748225] Call trace:
 [    0.750685]  lockdep_assert_cpus_held+0x30/0x40
 [    0.755236]  static_key_enable_cpuslocked+0x20/0xc8
 [    0.760137]  build_sched_domains+0x1034/0x1108
 [    0.764601]  sched_init_domains+0x68/0x90
 [    0.768628]  sched_init_smp+0x30/0x80
 [    0.772309]  kernel_init_freeable+0x278/0x51c
 [    0.776685]  kernel_init+0x10/0x108
 [    0.780190]  ret_from_fork+0x10/0x18

The static_key in question is 'sched_asym_cpucapacity' introduced by
commit:

  df054e8445a4 ("sched/topology: Add static_key for asymmetric CPU capacity optimizations")

In this particular case, we enable it because smp_prepare_cpus() will
end up fetching the capacity-dmips-mhz entry from the devicetree,
so we already have some asymmetry detected when entering sched_init_smp().

This didn't get detected in tip/sched/core because we were missing:

  commit cb538267ea1e ("jump_label/lockdep: Assert we hold the hotplug lock for _cpuslocked() operations")

Calls to build_sched_domains() post sched_init_smp() will hold the
hotplug lock, it just so happens that this very first call is a
special case. As stated by a comment in sched_init_smp(), "There's no
userspace yet to cause hotplug operations" so this is a harmless
warning.

However, to both respect the semantics of underlying
callees and make lockdep happy, take the hotplug lock in
sched_init_smp(). This also satisfies the comment atop
sched_init_domains() that says "Callers must hold the hotplug lock".

Reported-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Valentin Schneider <valentin.schneider@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Dietmar.Eggemann@arm.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: morten.rasmussen@arm.com
Cc: quentin.perret@arm.com
Link: http://lkml.kernel.org/r/1540301851-3048-1-git-send-email-valentin.schneider@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: qcom-geni: Fix runtime PM mismatch with child devices

[ Upstream commit 848bd3f3de9d44950c00eda6c115e8e9785440da ]

We need to enable runtime PM on this i2c controller before populating
child devices with i2c_add_adapter(). Otherwise, if a child device uses
runtime PM and stays runtime PM enabled we'll get the following warning
at boot.

 Enabling runtime PM for inactive device (a98000.i2c) with active children

[...]

 Call trace:
  pm_runtime_enable+0xd8/0xf8
  geni_i2c_probe+0x440/0x460
  platform_drv_probe+0x74/0xc8
[...]

Let's move the runtime PM enabling and setup to before we add the
adapter, so that this device can respond to runtime PM requests from
children.

Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: omap: Enable for ARCH_K3

[ Upstream commit 5b277402deac0691226a947df71c581686bd4020 ]

Allow I2C_OMAP to be built for K3 platforms.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme: make sure ns head inherits underlying device limits

[ Upstream commit 8f676b8508c250bbe255096522fdefb73f1ea0b9 ]

Whenever we update ns_head info, we need to make sure it is still
compatible with all underlying backing devices because although nvme
multipath doesn't have any explicit use of these limits, other devices
can still be stacked on top of it which may rely on the underlying limits.
Start with unlimited stacking limits, and every info update iterate over
siblings and adjust queue limits.

Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

of/device: Really only set bus DMA mask when appropriate

[ Upstream commit 6778be4e520959659b27a441c06a84c9cb009085 ]

of_dma_configure() was *supposed* to be following the same logic as
acpi_dma_configure() and only setting bus_dma_mask if some range was
specified by the firmware. However, it seems that subtlety got lost in
the process of fitting it into the differently-shaped control flow, and
as a result the force_dma==true case ends up always setting the bus mask
to the 32-bit default, which is not what anyone wants.

Make sure we only touch it if the DT actually said so.

Fixes: 6c2fb2ea7636 ("of/device: Set bus DMA mask as appropriate")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Reported-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Robert Richter <robert.richter@cavium.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ceph: quota: fix null pointer dereference in quota check

[ Upstream commit 71f2cc64d027d712f29bf8d09d3e123302d5f245 ]

This patch fixes a possible null pointer dereference in
check_quota_exceeded, detected by the static checker smatch, with the
following warning:

   fs/ceph/quota.c:240 check_quota_exceeded()
    error: we previously assumed 'realm' could be null (see line 188)

Fixes: b7a2921765cf ("ceph: quota: support for ceph.quota.max_files")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luis Henriques <lhenriques@suse.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/perf: Change CPUM_CF return code in event init function

[ Upstream commit 0bb2ae1b26e1fb7543ec7474cdd374ac4b88c4da ]

The function perf_init_event() creates a new event and
assignes it to a PMU. This a done in a loop over all existing
PMUs. For each listed PMU the event init function is called
and if this function does return any other error than -ENOENT,
the loop is terminated the creation of the event fails.

If the event is invalid, return -ENOENT to try other PMUs.

Signed-off-by: Thomas Richter <tmricht@linux.ibm.com>
Reviewed-by: Hendrik Brueckner <brueckner@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/amdgpu/dm: Fix dm_dp_create_fake_mst_encoder()

[ Upstream commit 63237f8748bdf46dccf79ef8f98f05e9fe799162 ]

[why]
Removing connector reusage from DM to match the rest of the tree ended
up revealing an issue that was surprisingly subtle. The original amdgpu
code for DC that was submitted appears to have left a chunk in
dm_dp_create_fake_mst_encoder() that tries to find a "master encoder",
the likes of which isn't actually used or stored anywhere. It does so at
the wrong time as well by trying to access parts of the drm_connector
from the encoder init before it's actually been initialized. This
results in a NULL pointer deref on MST hotplugs:

[  160.696613] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[  160.697234] PGD 0 P4D 0
[  160.697814] Oops: 0010 [#1] SMP PTI
[  160.698430] CPU: 2 PID: 64 Comm: kworker/2:1 Kdump: loaded Tainted: G           O      4.19.0Lyude-Test+ #2
[  160.699020] Hardware name: HP HP ZBook 15 G4/8275, BIOS P70 Ver. 01.22 05/17/2018
[  160.699672] Workqueue: events_long drm_dp_mst_link_probe_work [drm_kms_helper]
[  160.700322] RIP: 0010:          (null)
[  160.700920] Code: Bad RIP value.
[  160.701541] RSP: 0018:ffffc9000029fc78 EFLAGS: 00010206
[  160.702183] RAX: 0000000000000000 RBX: ffff8804440ed468 RCX: ffff8804440e9158
[  160.702778] RDX: 0000000000000000 RSI: ffff8804556c5700 RDI: ffff8804440ed000
[  160.703408] RBP: ffff880458e21800 R08: 0000000000000002 R09: 000000005fca0a25
[  160.704002] R10: ffff88045a077a3d R11: ffff88045a077a3c R12: ffff8804440ed000
[  160.704614] R13: ffff880458e21800 R14: ffff8804440e9000 R15: ffff8804440e9000
[  160.705260] FS:  0000000000000000(0000) GS:ffff88045f280000(0000) knlGS:0000000000000000
[  160.705854] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  160.706478] CR2: ffffffffffffffd6 CR3: 000000000200a001 CR4: 00000000003606e0
[  160.707124] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  160.707724] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  160.708372] Call Trace:
[  160.708998]  ? dm_dp_add_mst_connector+0xed/0x1d0 [amdgpu]
[  160.709625]  ? drm_dp_add_port+0x2fa/0x470 [drm_kms_helper]
[  160.710284]  ? wake_up_q+0x54/0x70
[  160.710877]  ? __mutex_unlock_slowpath.isra.18+0xb3/0x110
[  160.711512]  ? drm_dp_dpcd_access+0xe7/0x110 [drm_kms_helper]
[  160.712161]  ? drm_dp_send_link_address+0x155/0x1e0 [drm_kms_helper]
[  160.712762]  ? drm_dp_check_and_send_link_address+0xa3/0xd0 [drm_kms_helper]
[  160.713408]  ? drm_dp_mst_link_probe_work+0x4b/0x80 [drm_kms_helper]
[  160.714013]  ? process_one_work+0x1a1/0x3a0
[  160.714667]  ? worker_thread+0x30/0x380
[  160.715326]  ? wq_update_unbound_numa+0x10/0x10
[  160.715939]  ? kthread+0x112/0x130
[  160.716591]  ? kthread_create_worker_on_cpu+0x70/0x70
[  160.717262]  ? ret_from_fork+0x35/0x40
[  160.717886] Modules linked in: amdgpu(O) vfat fat snd_hda_codec_generic joydev i915 chash gpu_sched ttm i2c_algo_bit drm_kms_helper snd_hda_codec_hdmi hp_wmi syscopyarea iTCO_wdt sysfillrect sparse_keymap sysimgblt fb_sys_fops snd_hda_intel usbhid wmi_bmof drm snd_hda_codec btusb snd_hda_core intel_rapl btrtl x86_pkg_temp_thermal btbcm btintel coretemp snd_pcm crc32_pclmul bluetooth psmouse snd_timer snd pcspkr i2c_i801 mei_me i2c_core soundcore mei tpm_tis wmi tpm_tis_core hp_accel ecdh_generic lis3lv02d tpm video rfkill acpi_pad input_polldev hp_wireless pcc_cpufreq crc32c_intel serio_raw tg3 xhci_pci xhci_hcd [last unloaded: amdgpu]
[  160.720141] CR2: 0000000000000000

Somehow the connector reusage DM was using for MST connectors managed to
paper over this issue entirely; hence why this was never caught until
now.

[how]
Since this code isn't used anywhere and seems useless anyway, we can
just drop it entirely. This appears to fix the issue on my HP ZBook with
an AMD WX4150.

Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Drop reusing drm connector for MST

[ Upstream commit 0e6613e46fed29316f33acf86e1d1568288638b5 ]

[why]
It is not safe to keep existing connector while entire topology
has been removed. Could lead potential impact to uapi.
Entirely unregister all the connectors on the topology,
and use a new set of connectors when the topology is plugged back
on.

[How]
Remove the drm connector entirely each time when the
corresponding MST topology is gone.
When hotunplug a connector (e.g., DP2)
1. Remove connector from userspace.
2. Drop it's reference.
When hotplug back on:
1. Detect new topology, and create new connectors.
2. Notify userspace with sysfs hotplug event.
3. Reprobe new connectors, and reassign CRTC from old (e.g., DP2)
to new (e.g., DP3) connector.

Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

block: Clear kernel memory before copying to user

[ Upstream commit f3587d76da05f68098ddb1cb3c98cc6a9e8a402c ]

If the kernel allocates a bounce buffer for user read data, this memory
needs to be cleared before copying it to the user, otherwise it may leak
kernel memory to user space.

Laurence Oberman <loberman@redhat.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amd/display: Stop leaking planes

[ Upstream commit 02680efbb10be0d2c867fe722ae23d588f6bebef ]

[Why]
drm_plane_cleanup does not free the plane.

[How]
Call drm_primary_helper_destroy which will also free the plane.

Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

lib/raid6: Fix arm64 test build

[ Upstream commit 313a06e636808387822af24c507cba92703568b1 ]

The lib/raid6/test fails to build the neon objects
on arm64 because the correct machine type is 'aarch64'.

Once this is correctly enabled, the neon recovery objects
need to be added to the build.

Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

mtd: nand: Fix nanddev_pos_next_page() kernel-doc header

[ Upstream commit 98ee3fc7ef8395f8b7a379e6608aee91efc66d48 ]

Function name is wrong in the kernel-doc header.

Fixes: 9c3736a3de21 ("mtd: nand: Add core infrastructure to deal with NAND devices")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: fixed-factor: fix of_node_get-put imbalance

[ Upstream commit f98e8a572bddbf27032114127d2fcc78fa5e6a9d ]

When the fixed factor clock is created by devicetree,
of_clk_add_provider is called.  Add a call to
of_clk_del_provider in the remove function to balance
it out.

Reported-by: Alan Tull <atull@kernel.org>
Fixes: 971451b3b15d ("clk: fixed-factor: Convert into a module platform driver")
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

xen/grant-table: Fix incorrect gnttab_dma_free_pages() pr_debug message

[ Upstream commit d9cccfa7c4d1d9ef967ec9308df7304a18609b30 ]

If a call to xenmem_reservation_increase() in gnttab_dma_free_pages()
fails it triggers a message "Failed to decrease reservation..." which
should be "Failed to increase reservation..."

Fixes: 9bdc7304f536 ('xen/grant-table: Allow allocating buffers suitable for DMA')
Reported-by: Ross Philipson <ross.philipson@oracle.com>
Signed-off-by: Liam Merwick <liam.merwick@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: renesas: condor: switch from EtherAVB to GEther

[ Upstream commit eab53fdfd60a84b0cc514d4f1f5d79226c76df01 ]

The "official" Condor boards have always been wired to mount NFS via
GEther, not EtherAVB -- the boards resoldered for EtherAVB were local
to Cogent Embedded, so we've been having an unpleasant situation where
a "normal" Condor board still can't mount NFS (unless an EtherAVB PHY
extension board is plugged in). Switch from EtherAVB to GEther at last!

Fixes: 8091788f3d38 ("arm64: dts: renesas: condor: add EtherAVB support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: dts: renesas: r8a7795: add missing dma-names on hscif2

[ Upstream commit aab7a2414ba0d5c3d0571a90031b535adba7146a ]

hscif2 has 4 dmas, but has only 2 dma-names.
This patch add missing dma-names.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Fixes: e0f0bda79337701a ("arm64: dts: renesas: r8a7795: sort subnodes
of the soc node")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "drm/exynos/decon5433: implement frame counter"

[ Upstream commit 6ca469e22a30992b4478d2ab88737c70667c1e00 ]

This reverts commit 0586feba322e1de05075700eb4b835c8b683e62b

This patch makes it to need get_vblank_counter callback in crtc
to get frame counter from decon driver.

However, drm_dev->max_vblank_count is a member unique to
vendor's DRM driver but in case of ARM DRM, some CRTC devices
don't provide the frame counter value. As a result, this patch
made extension and clone mode not working.

Instead of this patch, we may need separated max_vblank_count
which belongs to each CRTC device, or need to implement frame
counter emulation for them who don't support HW frame counter.

Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: fsl: Fix improperly quoted stdout-path values

[ Upstream commit 1af6ab3bac8458fc2e92ad7bb97b62de4a1fddef ]

A quoted label reference doesn't expand to the node path and is taken as
a literal string. Dropping the quotes can fix this unless the baudrate
string is appended in which case we have to use the alias.

At least on VF610, the problem was masked by setting the console in
bootargs. Use the alias syntax with baudrate parameter so we can drop
setting the console in bootargs.

Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: dts: imx6sll: fix typo for fsl,imx6sll-i2c node

[ Upstream commit 438ad09af5581b7024850b5dbb6353c7f2f7d8a9 ]

Fix the type of compatible string "fs,imx6sll-i2c" which should be
"fsl,imx6sll-i2c".

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (ibmpowernv) Remove bogus __init annotations

[ Upstream commit e3e61f01d755188cb6c2dcf5a244b9c0937c258e ]

If gcc decides not to inline make_sensor_label():

    WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
    The function .create_device_attrs() references
    the function __init .make_sensor_label().
    This is often because .create_device_attrs lacks a __init
    annotation or the annotation of .make_sensor_label is wrong.

As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: Fix for out-of-bounds access when setting pfc back pressure

[ Upstream commit e8ccbb7d2f53c62e14b889faaa3f6f809b657278 ]

The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.

[   35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14

[   35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[   35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[   35.254141] Workqueue: events work_for_cpu_fn
[   35.254144] Call trace:
[   35.254147]  dump_backtrace+0x0/0x2f0
[   35.254149]  show_stack+0x24/0x30
[   35.254154]  dump_stack+0x110/0x184
[   35.254157]  print_address_description+0x168/0x2b0
[   35.254160]  kasan_report+0x184/0x310
[   35.254162]  __asan_load2+0x7c/0xa0
[   35.254170]  hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[   35.254177]  hclge_tm_init_hw+0x794/0x9f0 [hclge]
[   35.254184]  hclge_tm_schd_init+0x48/0x58 [hclge]
[   35.254191]  hclge_init_ae_dev+0x778/0x1168 [hclge]
[   35.254196]  hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[   35.254206]  hns3_probe+0x88/0xa8 [hns3]
[   35.254210]  local_pci_probe+0x7c/0xf0
[   35.254212]  work_for_cpu_fn+0x34/0x50
[   35.254214]  process_one_work+0x4d4/0xa38
[   35.254216]  worker_thread+0x55c/0x8d8
[   35.254219]  kthread+0x1b0/0x1b8
[   35.254222]  ret_from_fork+0x10/0x1c

[   35.254224] The buggy address belongs to the page:
[   35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[   35.273835] flags: 0xfffff8000008000(head)
[   35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[   35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[   35.282012] page dumped because: kasan: bad access detected

[   35.282014] Memory state around the buggy address:
[   35.282017]  ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282019]  ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282022]                             ^
[   35.282024]  ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282026]  ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[   35.282028] ==================================================================
[   35.282029] Disabling lock debugging due to kernel taint
[   35.282747] hclge driver initialization finished.

Fixes: 67bf2541f4b9 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/qeth: unregister netdevice only when registered

[ Upstream commit 30356d08159d7899438e94503ae322a8b881e205 ]

qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.

Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.

Fixes: d3d1b205e89f ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/qeth: fix HiperSockets sniffer

[ Upstream commit bd74a7f9cc033cf4d405788f80292268987dc0c5 ]

Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.

While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
   without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
   is switched off later we can operate just like normal.

Fixes: 5f78e29ceebf ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: nft_compat: ebtables 'nat' table is normal chain type

[ Upstream commit e4844c9c62a0fe47980d6c3d4b7a096a5d755925 ]

Unlike ip(6)tables, the ebtables nat table has no special properties.
This bug causes 'ebtables -A' to fail when using a target such as
'snat' (ebt_snat target sets ".table = "nat"').  Targets that have
no table restrictions work fine.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipset: Fix calling ip_set() macro at dumping

[ Upstream commit 8a02bdd50b2ecb6d62121d2958d3ea186cc88ce7 ]

The ip_set() macro is called when either ip_set_ref_lock held only
or no lock/nfnl mutex is held at dumping. Take this into account
properly. Also, use Pablo's suggestion to use rcu_dereference_raw(),
the ref_netlink protects the set.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: xt_IDLETIMER: add sysfs filename checking routine

[ Upstream commit 54451f60c8fa061af9051a53be9786393947367c ]

When IDLETIMER rule is added, sysfs file is created under
/sys/class/xt_idletimer/timers/
But some label name shouldn't be used.
".", "..", "power", "uevent", "subsystem", etc...
So that sysfs filename checking routine is needed.

test commands:
   %iptables -I INPUT -j IDLETIMER --timeout 1 --label "power"

splat looks like:
[95765.423132] sysfs: cannot create duplicate filename '/devices/virtual/xt_idletimer/timers/power'
[95765.433418] CPU: 0 PID: 8446 Comm: iptables Not tainted 4.19.0-rc6+ #20
[95765.449755] Call Trace:
[95765.449755]  dump_stack+0xc9/0x16b
[95765.449755]  ? show_regs_print_info+0x5/0x5
[95765.449755]  sysfs_warn_dup+0x74/0x90
[95765.449755]  sysfs_add_file_mode_ns+0x352/0x500
[95765.449755]  sysfs_create_file_ns+0x179/0x270
[95765.449755]  ? sysfs_add_file_mode_ns+0x500/0x500
[95765.449755]  ? idletimer_tg_checkentry+0x3e5/0xb1b [xt_IDLETIMER]
[95765.449755]  ? rcu_read_lock_sched_held+0x114/0x130
[95765.449755]  ? __kmalloc_track_caller+0x211/0x2b0
[95765.449755]  ? memcpy+0x34/0x50
[95765.449755]  idletimer_tg_checkentry+0x4e2/0xb1b [xt_IDLETIMER]
[ ... ]

Fixes: 0902b469bd25 ("netfilter: xtables: idletimer target implementation")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipset: Correct rcu_dereference() call in ip_set_put_comment()

[ Upstream commit 17b8b74c0f8dbf9b9e3301f9ca5b65dd1c079951 ]

The function is called when rcu_read_lock() is held and not
when rcu_read_lock_bh() is held.

Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bpf: fix bpf_prog_get_info_by_fd to return 0 func_lens for unpriv

[ Upstream commit 28c2fae726bf5003cd209b0d5910a642af98316f ]

While dbecd7388476 ("bpf: get kernel symbol addresses via syscall")
zeroed info.nr_jited_ksyms in bpf_prog_get_info_by_fd() for queries
from unprivileged users, commit 815581c11cc2 ("bpf: get JITed image
lengths of functions via syscall") forgot about doing so and therefore
returns the #elems of the user set up buffer which is incorrect. It
also needs to indicate a info.nr_jited_func_lens of zero.

Fixes: 815581c11cc2 ("bpf: get JITed image lengths of functions via syscall")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Sandipan Das <sandipan@linux.vnet.ibm.com>
Cc: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/mm: Fix ERROR: "__node_distance" undefined!

[ Upstream commit a541f0ebcc08ed8bc0cc492eec9a86cb280a9f24 ]

Fixes:
ERROR: "__node_distance" [drivers/nvme/host/nvme-core.ko] undefined!
make[1]: *** [scripts/Makefile.modpost:92: __modpost] Error 1
make: *** [Makefile:1275: modules] Error 2
+ exit 1

Signed-off-by: Justin M. Forbes <jforbes@fedoraproject.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/mm: fix mis-accounting of pgtable_bytes

[ Upstream commit e12e4044aede97974f2222eb7f0ed726a5179a32 ]

In case a fork or a clone system fails in copy_process and the error
handling does the mmput() at the bad_fork_cleanup_mm label, the
following warning messages will appear on the console:

  BUG: non-zero pgtables_bytes on freeing mm: 16384

The reason for that is the tricks we play with mm_inc_nr_puds() and
mm_inc_nr_pmds() in init_new_context().

A normal 64-bit process has 3 levels of page table, the p4d level and
the pud level are folded. On process termination the free_pud_range()
function in mm/memory.c will subtract 16KB from pgtable_bytes with a
mm_dec_nr_puds() call, but there actually is not really a pud table.

One issue with this is the fact that pgtable_bytes is usually off
by a few kilobytes, but the more severe problem is that for a failed
fork or clone the free_pgtables() function is not called. In this case
there is no mm_dec_nr_puds() or mm_dec_nr_pmds() that go together with
the mm_inc_nr_puds() and mm_inc_nr_pmds in init_new_context().
The pgtable_bytes will be off by 16384 or 32768 bytes and we get the
BUG message. The message itself is purely cosmetic, but annoying.

To fix this override the mm_pmd_folded, mm_pud_folded and mm_p4d_folded
function to check for the true size of the address space.

Reported-by: Li Wang <liwang@redhat.com>
Tested-by: Li Wang <liwang@redhat.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipset: fix ip_set_list allocation failure

[ Upstream commit ed956f3947a01ff9875cd908d7c1ef1fe7f47bf0 ]

ip_set_create() and ip_set_net_init() attempt to allocate physically
contiguous memory for ip_set_list. If memory is fragmented, the
allocations could easily fail:

        vzctl: page allocation failure: order:7, mode:0xc0d0

        Call Trace:
         dump_stack+0x19/0x1b
         warn_alloc_failed+0x110/0x180
         __alloc_pages_nodemask+0x7bf/0xc60
         alloc_pages_current+0x98/0x110
         kmalloc_order+0x18/0x40
         kmalloc_order_trace+0x26/0xa0
         __kmalloc+0x279/0x290
         ip_set_net_init+0x4b/0x90 [ip_set]
         ops_init+0x3b/0xb0
         setup_net+0xbb/0x170
         copy_net_ns+0xf1/0x1c0
         create_new_namespaces+0xf9/0x180
         copy_namespaces+0x8e/0xd0
         copy_process+0xb61/0x1a00
         do_fork+0x91/0x320

Use kvcalloc() to fallback to 0-order allocations if high order
page isn't available.

Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipset: actually allow allowable CIDR 0 in hash:net,port,net

[ Upstream commit 886503f34d63e681662057448819edb5b1057a97 ]

Allow /0 as advertised for hash:net,port,net sets.

For "hash:net,port,net", ipset(8) says that "either subnet
is permitted to be a /0 should you wish to match port
between all destinations."

Make that statement true.

Before:

    # ipset create cidrzero hash:net,port,net
    # ipset add cidrzero 0.0.0.0/0,12345,0.0.0.0/0
    ipset v6.34: The value of the CIDR parameter of the IP address is invalid

    # ipset create cidrzero6 hash:net,port,net family inet6
    # ipset add cidrzero6 ::/0,12345,::/0
    ipset v6.34: The value of the CIDR parameter of the IP address is invalid

After:

    # ipset create cidrzero hash:net,port,net
    # ipset add cidrzero 0.0.0.0/0,12345,0.0.0.0/0
    # ipset test cidrzero 192.168.205.129,12345,172.16.205.129
    192.168.205.129,tcp:12345,172.16.205.129 is in set cidrzero.

    # ipset create cidrzero6 hash:net,port,net family inet6
    # ipset add cidrzero6 ::/0,12345,::/0
    # ipset test cidrzero6 fe80::1,12345,ff00::1
    fe80::1,tcp:12345,ff00::1 is in set cidrzero6.

See also:

  https://bugzilla.kernel.org/show_bug.cgi?id=200897
  https://github.com/ewestbrook/linux/commit/df7ff6efb0934ab6acc11f003ff1a7580d6c1d9c

Signed-off-by: Eric Westbrook <linux@westbrook.io>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipset: list:set: Decrease refcount synchronously on deletion and replace

[ Upstream commit 439cd39ea136d2c026805264d58a91f36b6b64ca ]

Commit 45040978c899 ("netfilter: ipset: Fix set:list type crash
when flush/dump set in parallel") postponed decreasing set
reference counters to the RCU callback.

An 'ipset del' command can terminate before the RCU grace period
is elapsed, and if sets are listed before then, the reference
counter shown in userspace will be wrong:

 # ipset create h hash:ip; ipset create l list:set; ipset add l
 # ipset del l h; ipset list h
 Name: h
 Type: hash:ip
 Revision: 4
 Header: family inet hashsize 1024 maxelem 65536
 Size in memory: 88
 References: 1
 Number of entries: 0
 Members:
 # sleep 1; ipset list h
 Name: h
 Type: hash:ip
 Revision: 4
 Header: family inet hashsize 1024 maxelem 65536
 Size in memory: 88
 References: 0
 Number of entries: 0
 Members:

Fix this by making the reference count update synchronous again.

As a result, when sets are listed, ip_set_name_byindex() might
now fetch a set whose reference count is already zero. Instead
of relying on the reference count to protect against concurrent
set renaming, grab ip_set_ref_lock as reader and copy the name,
while holding the same lock in ip_set_rename() as writer
instead.

Reported-by: Li Shuang <shuali@redhat.com>
Fixes: 45040978c899 ("netfilter: ipset: Fix set:list type crash when flush/dump set in parallel")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "netfilter: nft_numgen: add map lookups for numgen random operations"

[ Upstream commit 4269fea768a11a447d8de620ce420f2214d4685c ]

Laura found a better way to do this from userspace without requiring
kernel infrastructure, revert this.

Fixes: 978d8f9055c3 ("netfilter: nft_numgen: add map lookups for numgen random operations")
Signed-off-by: Laura Garcia Liebana <nevola@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: alps: allow incoming reports when only the trackstick is opened

[ Upstream commit 7dd8db68949a7acc5bd528ee0ecb8f8720f49921 ]

If userspace only reads the trackstick node, and no one is listening to
the touchpad nor the hidraw node then, the device is not powered on.

Add open/close callbacks to allow users to disable the touchpad in Gnome
while keeping the trackstick active.

Link: https://bugzilla.redhat.com/show_bug.cgi?id=1559632
Link: https://gitlab.gnome.org/GNOME/mutter/issues/128
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Revert "HID: add NOGET quirk for Eaton Ellipse MAX UPS"

[ Upstream commit 6298944d8f57f40ee2a3e6dcea1253e78d7a9969 ]

This reverts commit 67ddbb3e6568fb1820b2cc45b00c50702b114801.

67ddbb3e656 ("HID: add NOGET quirk for Eaton Ellipse MAX UPS") was reported
by Laurent Bigonville. It turns out that a later model Laurent got
doesn't need the quirk after all.

My take is that Eaton upgraded their firmwares, so we don't need it
anymore.

The old model was from 2012, so better make sure the new line works
properly by removing the quirk. This allows upower to actually fetch
the current data.

Reported-by: Laurent Bigonville <bigon@bigon.be>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

HID: i2c-hid: Add a small delay after sleep command for Raydium touchpanel

[ Upstream commit 00b790ea545b6ef30221adef6e9c3707e03b82b5 ]

Raydium touchpanel (2386:4B33) sometimes does not work in desktop session
although it works in display manager.

During user logging, the display manager exits, close the HID device,
then the device gets runtime suspended and powered off. The desktop
session begins shortly after, opens the HID device, then the device gets
runtime resumed and powered on.

If the trasition from display manager to desktop sesesion is fast, the
touchpanel cannot switch from powered off to powered on in short
timeframe. So add a small delay to workaround the issue.

Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/vdso: add missing FORCE to build targets

[ Upstream commit b44b136a3773d8a9c7853f8df716bd1483613cbb ]

According to Documentation/kbuild/makefiles.txt all build targets using
if_changed should use FORCE as well. Add missing FORCE to make sure
vdso targets are rebuild properly when not just immediate prerequisites
have changed but also when build command differs.

Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

s390/decompressor: add missing FORCE to build targets

[ Upstream commit ef5febae1543f35a45f01614123e829d77326d0f ]

According to Documentation/kbuild/makefiles.txt all build targets
using if_changed should use FORCE as well. Add missing FORCE to make
sure vmlinux decompressor targets are rebuild properly when not just
immediate prerequisites have changed but also when build command differs.

Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: bridge: define INT_MIN & INT_MAX in userspace

[ Upstream commit 5a8de47b3c250521dd632cdedaac6db88367defa ]

With 4.19, programs like ebtables fail to build when they include
"linux/netfilter_bridge.h". It is caused by commit 94276fa8a2a4 which
added a use of INT_MIN and INT_MAX to the header:
: In file included from /usr/include/linux/netfilter_bridge/ebtables.h:18,
:                  from include/ebtables_u.h:28,
:                  from communication.c:23:
: /usr/include/linux/netfilter_bridge.h:30:20: error: 'INT_MIN' undeclared here (not in a function)
:   NF_BR_PRI_FIRST = INT_MIN,
:                     ^~~~~~~

Define these constants by including "limits.h" when !__KERNEL__ (the
same way as for other netfilter_* headers).

Fixes: 94276fa8a2a4 ("netfilter: bridge: Expose nf_tables bridge hook priorities through uapi")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Máté Eckl <ecklm94@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

netfilter: ipv6: fix oops when defragmenting locally generated fragments

[ Upstream commit 61792b677415b77c8db04991c22966bb8de7603e ]

Unlike ipv4 and normal ipv6 defrag, netfilter ipv6 defragmentation did
not save/restore skb->dst.

This causes oops when handling locally generated ipv6 fragments, as
output path needs a valid dst.

Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Fixes: 84379c9afe01 ("netfilter: ipv6: nf_defrag: drop skb dst before queueing")
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

serial: sh-sci: Fix receive on SCIFA/SCIFB variants with DMA

[ Upstream commit 202dc3cc10b4d37e5251431acf8d5040a8876c7d ]

On SCIFA and SCIFB serial ports with DMA support (i.e. some ports on
R-Car Gen2 and RZ/G1 SoCs), receive DMA operations are submitted before
the DMA channel pointer is initialized.  Hence this fails, and the
driver tries to fall back to PIO.  However, at this early phase in the
initialization sequence, fallback to PIO does not work, leading to a
serial port that cannot receive any data.

Fix this by calling sci_submit_rx() after initialization of the DMA
channel pointer.

Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2c4ee23530ffc022 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: ti: fix OF child-node lookup

[ Upstream commit 00a461cc32ec27fa7bd9c874a7b36b0c6c542c12 ]

Fix child-node lookup which by using the wrong OF helper was searching
the whole tree depth-first, something which could end up matching an
unrelated node.

Also fix the related node-reference leaks.

Fixes: 5b385a45e001 ("clk: ti: add support for clkctrl aliases")
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: renesas: r9a06g032: Fix UART34567 clock rate

[ Upstream commit ee02950d53eee0d4c7f1c08a35272b77d24b9459 ]

The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.

In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.

This change stops the UART34567 clock rate from changing for the same
reasons.

Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526eba2143 ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: meson: clk-pll: drop CLK_GET_RATE_NOCACHE where unnecessary

[ Upstream commit 2303a9ca693e585a558497ad737728fec97e2b8a ]

CLK_GET_RATE_NOCACHE should only be necessary when the registers
controlling the rate of clock may change outside of CCF. On Amlogic,
it should only be the case for the hdmi pll which is directly controlled
by the display driver (WIP to fix this).

The other plls should not require this flag.

Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

arm64: percpu: Initialize ret in the default case

[ Upstream commit b5bb425871186303e6936fa2581521bdd1964a58 ]

Clang warns that if the default case is taken, ret will be
uninitialized.

./arch/arm64/include/asm/percpu.h:196:2: warning: variable 'ret' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]
        default:
        ^~~~~~~
./arch/arm64/include/asm/percpu.h:200:9: note: uninitialized use occurs
here
        return ret;
               ^~~
./arch/arm64/include/asm/percpu.h:157:19: note: initialize the variable
'ret' to silence this warning
        unsigned long ret, loop;
                         ^
                          = 0

This warning appears several times while building the erofs filesystem.
While it's not strictly wrong, the BUILD_BUG will prevent this from
becoming a true problem. Initialize ret to 0 in the default case right
before the BUILD_BUG to silence all of these warnings.

Reported-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: meson-axg: pcie: drop the mpll3 clock parent

[ Upstream commit 69b93104c7ec5668019caf5d2dbfd0e182df06db ]

We found the PCIe driver doesn't really work with
the mpll3 clock which is actually reserved for debug,
So drop it from the mux list.

Fixes: 33b89db68236 ("clk: meson-axg: add clocks required by pcie driver")
Tested-by: Jianxin Qin <jianxin.qin@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: acerhdf: Add BIOS entry for Gateway LT31 v1.3307

[ Upstream commit 684238d79ad85c5e19a71bb5818e77e329912fbc ]

To fix:

  acerhdf: unknown (unsupported) BIOS version Gateway  /LT31   /v1.3307 , please report, aborting!

As can be seen in the context, the BIOS registers haven't changed in
the previous versions, so the assumption is they won't have changed
in this last update for this somewhat older platform either.

Cc: Peter Feuerer <peter@piie.net>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Peter Feuerer <peter@piie.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/earlyprintk: Add a force option for pciserial device

[ Upstream commit d2266bbfa9e3e32e3b642965088ca461bd24a94f ]

The "pciserial" earlyprintk variant helps much on many modern x86
platforms, but unfortunately there are still some platforms with PCI
UART devices which have the wrong PCI class code. In that case, the
current class code check does not allow for them to be used for logging.

Add a sub-option "force" which overrides the class code check and thus
the use of such device can be enforced.

 [ bp: massage formulations. ]

Suggested-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Stuart R . Anderson" <stuart.r.anderson@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: Frederic Weisbecker <frederic@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: H Peter Anvin <hpa@linux.intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thymo van Beers <thymovanbeers@gmail.com>
Cc: alan@linux.intel.com
Cc: linux-doc@vger.kernel.org
Link: http://lkml.kernel.org/r/20181002164921.25833-1-feng.tang@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

apparmor: Fix uninitialized value in aa_split_fqname

[ Upstream commit 250f2da49cb8e582215a65c03f50e8ddf5cd119c ]

Syzkaller reported a OOB-read with the stacktrace below. This occurs
inside __aa_lookupn_ns as `n` is not initialized. `n` is obtained from
aa_splitn_fqname. In cases where `name` is invalid, aa_splitn_fqname
returns without initializing `ns_name` and `ns_len`.

Fix this by always initializing `ns_name` and `ns_len`.

__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c4/0x2b4 lib/dump_stack.c:113
print_address_description.cold.8+0x9/0x1ff mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report.cold.9+0x242/0x309 mm/kasan/report.c:412
__asan_report_load1_noabort+0x14/0x20 mm/kasan/report.c:430
memcmp+0xe3/0x160 lib/string.c:861
strnstr+0x4b/0x70 lib/string.c:934
__aa_lookupn_ns+0xc1/0x570 security/apparmor/policy_ns.c:209
aa_lookupn_ns+0x88/0x1e0 security/apparmor/policy_ns.c:240
aa_fqlookupn_profile+0x1b9/0x1010 security/apparmor/policy.c:468
fqlookupn_profile+0x80/0xc0 security/apparmor/label.c:1844
aa_label_strn_parse+0xa3a/0x1230 security/apparmor/label.c:1908
aa_label_parse+0x42/0x50 security/apparmor/label.c:1943
aa_change_profile+0x513/0x3510 security/apparmor/domain.c:1362
apparmor_setprocattr+0xaa4/0x1150 security/apparmor/lsm.c:658
security_setprocattr+0x66/0xc0 security/security.c:1298
proc_pid_attr_write+0x301/0x540 fs/proc/base.c:2555
__vfs_write+0x119/0x9f0 fs/read_write.c:485
vfs_write+0x1fc/0x560 fs/read_write.c:549
ksys_write+0x101/0x260 fs/read_write.c:598
__do_sys_write fs/read_write.c:610 [inline]
__se_sys_write fs/read_write.c:607 [inline]
__x64_sys_write+0x73/0xb0 fs/read_write.c:607
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 3b0aaf5866bf ("apparmor: add lib fn to find the "split" for fqnames")
Reported-by: syzbot+61e4b490d9d2da591b50@syzkaller.appspotmail.com
Signed-off-by: Zubin Mithra <zsm@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: John Johansen <john.johansen@canonical.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: samsung: exynos5420: Enable PERIS clocks for suspend

[ Upstream commit b33228029d842269e17bba591609e83ed422005d ]

Ensure that clocks for core SoC modules (including TZPC0..9 modules)
are enabled for suspend/resume cycle. This fixes suspend/resume
support on Exynos5422-based Odroid XU3/XU4 boards.

Suggested-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Sylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

fs/exofs: fix potential memory leak in mount option parsing

[ Upstream commit 515f1867addaba49c1c6ac73abfaffbc192c1db4 ]

There are some cases can cause memory leak when parsing
option 'osdname'.

Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf symbols: Set PLT entry/header sizes properly on Sparc

[ Upstream commit d6afa561e1471ccfdaf7191230c0c59a37e45a5b ]

Using the sh_entsize for both values isn't correct.  It happens to be
correct on x86...

For both 32-bit and 64-bit sparc, there are four PLT entries in the PLT
section.

Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexis Berlemont <alexis.berlemont@gmail.com>
Cc: David Tolnay <dtolnay@gmail.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Hemant Kumar <hemant@linux.vnet.ibm.com>
Cc: Li Bin <huawei.libin@huawei.com>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: zhangmengting@huawei.com
Fixes: b2f7605076d6 ("perf symbols: Fix plt entry calculation for ARM and AARCH64")
Link: http://lkml.kernel.org/r/20181017.120859.2268840244308635255.davem@davemloft.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

clk: fixed-rate: fix of_node_get-put imbalance

[ Upstream commit 52091c256bdcad0d01e2852a63f19cd2cce6af96 ]

When the fixed rate clock is created by devicetree,
of_clk_add_provider is called.  Add a call to
of_clk_del_provider in the remove function to balance
it out.

Signed-off-by: Alan Tull <atull@kernel.org>
Fixes: 435779fe1336 ("clk: fixed-rate: Convert into a module platform driver")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

platform/x86: intel_telemetry: report debugfs failure

[ Upstream commit 8d98b1ef368feeb7720b8b9b6f3bd93f2ad892bc ]

On some Goldmont based systems such as ASRock J3455M the BIOS may not
enable the IPC1 device that provides access to the PMC and PUNIT. In
such scenarios, the IOSS and PSS resources from the platform device can
not be obtained and result in a invalid telemetry_plt_config which is an
internal data structure that holds platform config and is maintained by
the telemetry platform driver.

This is also applicable to the platforms where the BIOS supports IPC1
device under debug configurations but IPC1 is disabled by user or the
policy.

This change allows user to know the reason for not seeing entries under
/sys/kernel/debug/telemetry/* when there is no apparent failure at boot.

Cc: Matt Turner <matt.turner@intel.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Souvik Kumar Chakravarty <souvik.k.chakravarty@intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=198779
Acked-by: Matt Turner <matt.turner@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

afs: Handle EIO from delivery function

[ Upstream commit 4ac15ea53622272c01954461b4814892b7481b40 ]

Fix afs_deliver_to_call() to handle -EIO being returned by the operation
delivery function, indicating that the call found itself in the wrong
state, by printing an error and aborting the call.

Currently, an assertion failure will occur.  This can happen, say, if the
delivery function falls off the end without calling afs_extract_data() with
the want_more parameter set to false to collect the end of the Rx phase of
a call.

The assertion failure looks like:

AFS: Assertion failed
4 == 7 is false
0x4 == 0x7 is false
------------[ cut here ]------------
kernel BUG at fs/afs/rxrpc.c:462!

and is matched in the trace buffer by a line like:

kworker/7:3-3226 [007] ...1 85158.030203: afs_io_error: c=0003be0c r=-5 CM_REPLY

Fixes: 98bf40cd99fc ("afs: Protect call->state changes against signals")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/edid: Add 6 bpc quirk for BOE panel.

[ Upstream commit 922dceff8dc1fb4dafc9af78139ba65671408103 ]

BOE panel (ID: 0x0771) that reports "DFP 1.x compliant TMDS".
But it's 6bpc panel only instead of 8 bpc.

Add panel ID to edid quirk list and set 6 bpc as default to
work around this issue.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Signed-off-by: Lee, Shawn C <shawn.c.lee@intel.com>>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540792173-7288-1-git-send-email-shawn.c.lee@intel.com
Signed-off-by: Sasha Levin <sashal@kernel.org>

um: Give start_idle_thread() a return code

[ Upstream commit 7ff1e34bbdc15acab823b1ee4240e94623d50ee8 ]

Fixes:
arch/um/os-Linux/skas/process.c:613:1: warning: control reaches end of
non-void function [-Wreturn-type]

longjmp() never returns but gcc still warns that the end of the function
can be reached.
Add a return code and debug aid to detect this impossible case.

Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>

perf unwind: Take pgoff into account when reporting elf to libdwfl

[ Upstream commit 1fe627da30331024f453faef04d500079b901107 ]

libdwfl parses an ELF file itself and creates mappings for the
individual sections. perf on the other hand sees raw mmap events which
represent individual sections. When we encounter an address pointing
into a mapping with pgoff != 0, we must take that into account and
report the file at the non-offset base address.

This fixes unwinding with libdwfl in some cases. E.g. for a file like:

```

using namespace std;

mutex g_mutex;

double worker()
{
    lock_guard<mutex> guard(g_mutex);
    uniform_real_distribution<double> uniform(-1E5, 1E5);
    default_random_engine engine;
    double s = 0;
    for (int i = 0; i < 1000; ++i) {
        s += norm(complex<double>(uniform(engine), uniform(engine)));
    }
    cout << s << endl;
    return s;
}

int main()
{
    vector<std::future<double>> results;
    for (int i = 0; i < 10000; ++i) {
        results.push_back(async(launch::async, worker));
    }
    return 0;
}
```

Compile it with `g++ -g -O2 -lpthread cpp-locking.cpp  -o cpp-locking`,
then record it with `perf record --call-graph dwarf -e
sched:sched_switch`.

When you analyze it with `perf script` and libunwind, you should see:

```
cpp-locking 20038 [005] 54830.236589: sched:sched_switch: prev_comm=cpp-locking prev_pid=20038 prev_prio=120 prev_state=T ==> next_comm=swapper/5 next_pid=0 next_prio=120
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1670208 schedule+0x28 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb16737cc rwsem_down_read_failed+0xec (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1665e04 call_rwsem_down_read_failed+0x14 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1672a03 down_read+0x13 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb106bd85 __do_page_fault+0x445 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb18015f5 page_fault+0x45 (/lib/modules/4.14.78-1-lts/build/vmlinux)
            7f38e4252591 new_heap+0x101 (/usr/lib/libc-2.28.so)
            7f38e4252d0b arena_get2.part.4+0x2fb (/usr/lib/libc-2.28.so)
            7f38e4255b1c tcache_init.part.6+0xec (/usr/lib/libc-2.28.so)
            7f38e42569e5 __GI___libc_malloc+0x115 (inlined)
            7f38e4241790 __GI__IO_file_doallocate+0x90 (inlined)
            7f38e424fbbf __GI__IO_doallocbuf+0x4f (inlined)
            7f38e424ee47 __GI__IO_file_overflow+0x197 (inlined)
            7f38e424df36 _IO_new_file_xsputn+0x116 (inlined)
            7f38e4242bfb __GI__IO_fwrite+0xdb (inlined)
            7f38e463fa6d std::basic_streambuf<char, std::char_traits<char> >::sputn(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> >::_M_put(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::__write<char>(std::ostreambuf_iterator<char, std::char_traits<char> >, char const*, int)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::_M_insert_float<double>(std::ostreambuf_iterator<c>
            7f38e464bd70 std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::put(std::ostreambuf_iterator<char, std::char_traits<char> >, std::ios_base&, char, double) const+0x90 (inl>
            7f38e464bd70 std::ostream& std::ostream::_M_insert<double>(double)+0x90 (/usr/lib/libstdc++.so.6.0.25)
            563b9cb502f7 std::ostream::operator<<(double)+0xb7 (inlined)
            563b9cb502f7 worker()+0xb7 (/ssd/milian/projects/kdab/rnd/hotspot/build/tests/test-clients/cpp-locking/cpp-locking)
            563b9cb506fb double std::__invoke_impl<double, double (*)()>(std::__invoke_other, double (*&&)())+0x2b (inlined)
            563b9cb506fb std::__invoke_result<double (*)()>::type std::__invoke<double (*)()>(double (*&&)())+0x2b (inlined)
            563b9cb506fb decltype (__invoke((_S_declval<0ul>)())) std::thread::_Invoker<std::tuple<double (*)()> >::_M_invoke<0ul>(std::_Index_tuple<0ul>)+0x2b (inlined)
            563b9cb506fb std::thread::_Invoker<std::tuple<double (*)()> >::operator()()+0x2b (inlined)
            563b9cb506fb std::__future_base::_Task_setter<std::unique_ptr<std::__future_base::_Result<double>, std::__future_base::_Result_base::_Deleter>, std::thread::_Invoker<std::tuple<double (*)()> >, dou>
            563b9cb506fb std::_Function_handler<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> (), std::__future_base::_Task_setter<std::unique_ptr<std::__future_>
            563b9cb507e8 std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>::operator()() const+0x28 (inlined)
            563b9cb507e8 std::__future_base::_State_baseV2::_M_do_set(std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>*, bool*)+0x28 (/ssd/milian/>
            7f38e46d24fe __pthread_once_slow+0xbe (/usr/lib/libpthread-2.28.so)
            563b9cb51149 __gthread_once+0xe9 (inlined)
            563b9cb51149 void std::call_once<void (std::__future_base::_State_baseV2::*)(std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>*, bool*)>
            563b9cb51149 std::__future_base::_State_baseV2::_M_set_result(std::function<std::unique_ptr<std::__future_base::_Result_base, std::__future_base::_Result_base::_Deleter> ()>, bool)+0xe9 (inlined)
            563b9cb51149 std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<double (*)()> >&&)::{lambda()#1}::op>
            563b9cb51149 void std::__invoke_impl<void, std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<double>
            563b9cb51149 std::__invoke_result<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<double (*)()> >>
            563b9cb51149 decltype (__invoke((_S_declval<0ul>)())) std::thread::_Invoker<std::tuple<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_>
            563b9cb51149 std::thread::_Invoker<std::tuple<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread::_Invoker<std::tuple<dou>
            563b9cb51149 std::thread::_State_impl<std::thread::_Invoker<std::tuple<std::__future_base::_Async_state_impl<std::thread::_Invoker<std::tuple<double (*)()> >, double>::_Async_state_impl(std::thread>
            7f38e45f0062 execute_native_thread_routine+0x12 (/usr/lib/libstdc++.so.6.0.25)
            7f38e46caa9c start_thread+0xfc (/usr/lib/libpthread-2.28.so)
            7f38e42ccb22 __GI___clone+0x42 (inlined)
```

Before this patch, using libdwfl, you would see:

```
cpp-locking 20038 [005] 54830.236589: sched:sched_switch: prev_comm=cpp-locking prev_pid=20038 prev_prio=120 prev_state=T ==> next_comm=swapper/5 next_pid=0 next_prio=120
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1670208 schedule+0x28 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb16737cc rwsem_down_read_failed+0xec (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1665e04 call_rwsem_down_read_failed+0x14 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1672a03 down_read+0x13 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb106bd85 __do_page_fault+0x445 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb18015f5 page_fault+0x45 (/lib/modules/4.14.78-1-lts/build/vmlinux)
            7f38e4252591 new_heap+0x101 (/usr/lib/libc-2.28.so)
        a041161e77950c5c [unknown] ([unknown])
```

With this patch applied, we get a bit further in unwinding:

```
cpp-locking 20038 [005] 54830.236589: sched:sched_switch: prev_comm=cpp-locking prev_pid=20038 prev_prio=120 prev_state=T ==> next_comm=swapper/5 next_pid=0 next_prio=120
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb166fec5 __sched_text_start+0x545 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1670208 schedule+0x28 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb16737cc rwsem_down_read_failed+0xec (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1665e04 call_rwsem_down_read_failed+0x14 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb1672a03 down_read+0x13 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb106bd85 __do_page_fault+0x445 (/lib/modules/4.14.78-1-lts/build/vmlinux)
        ffffffffb18015f5 page_fault+0x45 (/lib/modules/4.14.78-1-lts/build/vmlinux)
            7f38e4252591 new_heap+0x101 (/usr/lib/libc-2.28.so)
            7f38e4252d0b arena_get2.part.4+0x2fb (/usr/lib/libc-2.28.so)
            7f38e4255b1c tcache_init.part.6+0xec (/usr/lib/libc-2.28.so)
            7f38e42569e5 __GI___libc_malloc+0x115 (inlined)
            7f38e4241790 __GI__IO_file_doallocate+0x90 (inlined)
            7f38e424fbbf __GI__IO_doallocbuf+0x4f (inlined)
            7f38e424ee47 __GI__IO_file_overflow+0x197 (inlined)
            7f38e424df36 _IO_new_file_xsputn+0x116 (inlined)
            7f38e4242bfb __GI__IO_fwrite+0xdb (inlined)
            7f38e463fa6d std::basic_streambuf<char, std::char_traits<char> >::sputn(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> >::_M_put(char const*, long)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::__write<char>(std::ostreambuf_iterator<char, std::char_traits<char> >, char const*, int)+0x1cd (inlined)
            7f38e463fa6d std::ostreambuf_iterator<char, std::char_traits<char> > std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::_M_insert_float<double>(std::ostreambuf_iterator<c>
            7f38e464bd70 std::num_put<char, std::ostreambuf_iterator<char, std::char_traits<char> > >::put(std::ostreambuf_iterator<char, std::char_traits<char> >, std::ios_base&, char, double) const+0x90 (inl>
            7f38e464bd70 std::ostream& std::ostream::_M_insert<double>(double)+0x90 (/usr/lib/libstdc++.so.6.0.25)
            563b9cb502f7 std::ostream::operator<<(double)+0xb7 (inlined)
            563b9cb502f7 worker()+0xb7 (/ssd/milian/projects/kdab/rnd/hotspot/build/tests/test-clients/cpp-locking/cpp-locking)
        6eab825c1ee3e4ff [unknown] ([unknown])
```

Note that the backtrace is still stopping too early, when compared to
the nice results obtained via libunwind. It's unclear so far what the
reason for that is.

Committer note:

Further comment by Milian on the thread started on the Link: tag below:

 ---
The remaining issue is due to a bug in elfutils:

https://sourceware.org/ml/elfutils-devel/2018-q4/msg00089.html

With both patches applied, libunwind and elfutils produce the same output for
the above scenario.
 ---

Signed-off-by: Milian Wolff <milian.wolff@kdab.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20181029141644.3907-1-milian.wolff@kdab.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hfsplus: prevent btree data loss on root split

[ Upstream commit 0a3021d4f5295aa073c7bf5c5e4de60a2e292578 ]

Creating, renaming or deleting a file may cause catalog corruption and
data loss.  This bug is randomly triggered by xfstests generic/027, but
here is a faster reproducer:

  truncate -s 50M fs.iso
  mkfs.hfsplus fs.iso
  mount fs.iso /mnt
  i=100
  while [ $i -le 150 ]; do
    touch /mnt/$i &>/dev/null
    ((++i))
  done
  i=100
  while [ $i -le 150 ]; do
    mv /mnt/$i /mnt/$(perl -e "print $i x82") &>/dev/null
    ((++i))
  done
  umount /mnt
  fsck.hfsplus -n fs.iso

The bug is triggered whenever hfs_brec_update_parent() needs to split the
root node.  The height of the btree is not increased, which leaves the new
node orphaned and its records lost.

Link: http://lkml.kernel.org/r/26d882184fc43043a810114258f45277752186c7.1535682461.git.ernesto.mnd.fernandez@gmail.com
Signed-off-by: Ernesto A. Fernández <ernesto.mnd.fernandez@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hfs: prevent btree data loss on root split

[ Upstream commit d057c036672f33d43a5f7344acbb08cf3a8a0c09 ]

This bug is triggered whenever hfs_brec_update_parent() needs to split
the root node.  The height of the btree is not increased, which leaves
the new node orphaned and its records lost.  It is not possible for this
to happen on a valid hfs filesystem because the index nodes have fixed
length keys.

For reasons I ignore, the hfs module does have support for a number of
hfsplus features.  A corrupt btree header may report variable length
keys and trigger this bug, so it's better to fix it.

Link: http://lkml.kernel.org/r/9750b1415685c4adca10766895f6d5ef12babdb0.1535682463.git.ernesto.mnd.fernandez@gmail.com
Signed-off-by: Ernesto A. Fernández <ernesto.mnd.fernandez@gmail.com>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

reiserfs: propagate errors from fill_with_dentries() properly

[ Upstream commit b10298d56c9623f9b173f19959732d3184b35f4f ]

fill_with_dentries() failed to propagate errors up to
reiserfs_for_each_xattr() properly.  Plumb them through.

Note that reiserfs_for_each_xattr() is only used by
reiserfs_delete_xattrs() and reiserfs_chown_xattrs().  The result of
reiserfs_delete_xattrs() is discarded anyway, the only difference there is
whether a warning is printed to dmesg.  The result of
reiserfs_chown_xattrs() does matter because it can block chowning of the
file to which the xattrs belong; but either way, the resulting state can
have misaligned ownership, so my patch doesn't improve things greatly.

Credit for making me look at this code goes to Al Viro, who pointed out
that the ->actor calling convention is suboptimal and should be changed.

Link: http://lkml.kernel.org/r/20180802163335.83312-1-jannh@google.com
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeff Mahoney <jeffm@suse.com>
Cc: Eric Biggers <ebiggers@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ixgbe: fix MAC anti-spoofing filter after VFLR

[ Upstream commit 6702185c1ffec3421181b5e24491e3fac920cb61 ]

This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.

MAC and VLAN anti-spoofing filters are to be enabled together.

Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: bugfix for the initialization of command queue's spin lock

[ Upstream commit b2f74dbaf12bf59ff35d451005b3cdee78232ff0 ]

The spin lock of the command queue only need to be initialized once
when the driver initializes the command queue. It is not necessary to
initialize the spin lock when resetting. At the same time, the
modification of the queue member should be performed after acquiring
the lock.

Fixes: 3efb960f056d ("net: hns3: Refactor the initialization of command queue")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: bugfix for handling mailbox while the command queue reinitialized

[ Upstream commit 3c88ed1d798da355859ca083d3884a16ce0841f2 ]

In a multi-core machine, the mailbox service and reset service
will be executed at the same time. The reset service will re-initialize
the command queue, before that, the mailbox handler can only get some
invalid messages.

The HCLGE_STATE_CMD_DISABLE flag means that the command queue is not
available and needs to be reinitialized. Therefore, when the mailbox
handler recognizes this flag, it should not process the command.

Fixes: dde1a86e93ca ("net: hns3: Add mailbox support to PF driver")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: bugfix for rtnl_lock's range in the hclge_reset()

[ Upstream commit a963052e539887df481d4d3a6ad4c92ca6461852 ]

Since hclge_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclge_reset_wait(). So this patch releases the lock for the duration
of hclge_reset_wait().

Fixes: 6d4fab39533f ("net: hns3: Reset net device with rtnl_lock")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: hns3: bugfix for rtnl_lock's range in the hclgevf_reset()

[ Upstream commit 29118ab962d5476fdc65fae312ac38db68092d78 ]

Since hclgevf_reset_wait() is used to wait for the hardware to complete
the reset, it is not necessary to hold the rtnl_lock during
hclgevf_reset_wait(). So this patch releases the lock for the duration
of hclgevf_reset_wait().

Fixes: 6988eb2a9b77 ("net: hns3: Add support to reset the enet/ring mgmt layer")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>