Haavard Skinnemoen [Fri, 29 Jun 2007 16:22:34 +0000 (18:22 +0200)]
atmel_mci: Show SR when block read fails
Show controller status as well as card status when an error occurs
during block read.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Stefan Roese [Thu, 13 Dec 2007 13:52:53 +0000 (14:52 +0100)]
ppc4xx: Bring 4xx fdt support up-to-date
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Thu, 13 Dec 2007 13:02:42 +0000 (14:02 +0100)]
Merge commit 'u-boot-fdt/testing'
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:34 +0000 (12:56 +0100)]
cfi_flash: Use map_physmem() and unmap_physmem()
Use map_physmem() and unmap_physmem() to convert from physical to
virtual addresses. This gives the arch a chance to provide an uncached
mapping for flash accesses.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:33 +0000 (12:56 +0100)]
Introduce map_physmem() and unmap_physmem()
map_physmem() returns a virtual address which can be used to access a
given physical address without involving the cache. unmap_physmem()
should be called when the virtual address returned by map_physmem() is
no longer needed.
This patch adds a stub implementation which simply returns the
physical address cast to a uchar * for all architectures except AVR32,
which converts the physical address to an uncached virtual mapping.
unmap_physmem() is a no-op on all architectures, but if any
architecture needs to do such mappings through the TLB, this is the
hook where those TLB entries can be invalidated.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:32 +0000 (12:56 +0100)]
cfi_flash: Introduce read and write accessors
Introduce flash_read{8,16,32,64) and flash_write{8,16,32,64} and use
them to access the flash memory. This makes it clearer when the flash
is actually being accessed; merely dereferencing a volatile pointer
looks just like any other kind of access.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:31 +0000 (12:56 +0100)]
Implement __raw_{read,write}[bwl] on all architectures
This adds implementations of __raw_read[bwl] and __raw_write[bwl] to
m68k, ppc, nios and nios2. The m68k and ppc implementations were taken
from Linux.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Sat, 6 Oct 2007 16:55:36 +0000 (18:55 +0200)]
cfi_flash: Reorder functions and eliminate extra prototypes
Reorder the functions in cfi_flash.c so that each function only uses
functions that have been defined before it. This allows the static
prototype declarations near the top to be eliminated and might allow
gcc to do a better job inlining functions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:29 +0000 (12:56 +0100)]
cfi_flash: Make some needlessly global functions static
Make functions not declared in any header file static.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Haavard Skinnemoen [Thu, 13 Dec 2007 11:56:28 +0000 (12:56 +0100)]
cfi_flash: Break long lines
This patch tries to keep all lines in the cfi_flash driver below 80
columns. There are a few lines left which don't fit this requirement
because I couldn't find any trivial way to break them (i.e. it would
take some restructuring, which I intend to do in a later patch.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Bartlomiej Sieka [Tue, 11 Dec 2007 12:59:57 +0000 (13:59 +0100)]
CFI: synchronize command offsets with Linux CFI driver
Fixes non-working CFI Flash on the Inka4x0 board.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Kumar Gala [Fri, 7 Dec 2007 18:17:34 +0000 (12:17 -0600)]
Handle MPC85xx PCIe reset errata (PCI-Ex 38)
On the MPC85xx boards that have PCIe enable the PCIe errata fix.
(MPC8544DS, MPC8548CDS, MPC8568MDS).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 7 Dec 2007 18:04:30 +0000 (12:04 -0600)]
Update Freescale MPC85xx ADS/CDS/MDS board config
* Enabled CONFIG_CMD_ELF
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Fri, 7 Dec 2007 10:59:26 +0000 (04:59 -0600)]
Handle Asynchronous DDR clock on 85xx
The MPC8572 introduces the concept of an asynchronous DDR clock with
regards to the platform clock.
Introduce get_ddr_freq() to report the DDR freq regardless of sync/async
mode.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 16:34:28 +0000 (10:34 -0600)]
Update Freescale MPC85xx ADS/CDS/MDS board config
* Removed some misc environment setup
* Enabled CONFIG_CMDLINE_EDITING
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 16:47:44 +0000 (10:47 -0600)]
Move the MPC8541/MPC8555/MPC8548 CDS board under board/freescale.
Minor path corrections needed to ensure buildability.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 16:16:18 +0000 (10:16 -0600)]
Move the MPC8540 ADS board under board/freescale.
Minor path corrections needed to ensure buildability.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 16:14:50 +0000 (10:14 -0600)]
Move the MPC8560 ADS board under board/freescale.
Minor path corrections needed to ensure buildability.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 16:13:47 +0000 (10:13 -0600)]
Move the MPC8568 MDS board under board/freescale.
Minor path corrections needed to ensure buildability.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 08:18:59 +0000 (02:18 -0600)]
Use standard LAWAR_TRGT_IF_* defines for LAW setup on 85xx
We already had defines for LAWAR_TRGT_IF_* that we should use
rather than creating new ones. Also, added some missing defines for
PCIE targets.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 08:10:09 +0000 (02:10 -0600)]
Stop using immap_t on 85xx
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_*_ADDR as the base of the registers
instead of getting it via &immap.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 07:23:09 +0000 (01:23 -0600)]
Remove CONFIG_OF_FLAT_TREE related code from mpc85xx since we now use libfdt
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 07:06:19 +0000 (01:06 -0600)]
Update MPC8568 MDS to use libfdt
Updated the MPC8568 MDS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Haiying Wang [Wed, 14 Nov 2007 20:52:06 +0000 (15:52 -0500)]
Add PCI Express support on MPC8568MDS
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 06:11:44 +0000 (00:11 -0600)]
Update MPC85xx CDS to use libfdt
Updated the MPC85xx CDS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 04:54:27 +0000 (22:54 -0600)]
Update MPC8540 ADS to use libfdt
Updated the MPC8540 ADS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 04:40:31 +0000 (22:40 -0600)]
Update MPC8560 ADS to use libfdt
Updated the MPC8560 ADS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 28 Nov 2007 06:36:33 +0000 (00:36 -0600)]
Stop using immap_t for cpm offset on 85xx
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers
instead of getting it via &immap->im_cpm.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 28 Nov 2007 05:25:02 +0000 (23:25 -0600)]
Stop using immap_t for guts offset on 85xx
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 28 Nov 2007 04:42:34 +0000 (22:42 -0600)]
Update MPC8544 DS config
* Removed HAS_ETH2/HAS_ETH3 - MPC8544 only has TSEC1/2
* Removed some misc environment setup
* Moved to using fdtfile & fdtaddr as fdt env var names
* Enabled CONFIG_CMDLINE_EDITING
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 23:12:24 +0000 (17:12 -0600)]
Update MPC8544DS to use libfdt
Updated the MPC8544DS config to use libfdt and assume use of aliases for
ethernet, pci, and serial for the various fixups that are done.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 29 Nov 2007 06:15:30 +0000 (00:15 -0600)]
Add libfdt based ft_cpu_setup for mpc85xx
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Stefan Roese [Tue, 11 Dec 2007 12:38:19 +0000 (13:38 +0100)]
ppc4xx: Correct GPIO offset in gpio_config()
Thanks to Gary Jennejohn for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Tue, 11 Dec 2007 10:46:01 +0000 (11:46 +0100)]
rtc: Fix merging problem
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Tue, 11 Dec 2007 10:34:54 +0000 (11:34 +0100)]
Merge commit 'u-boot/master' into for-1.3.1
Conflicts:
drivers/rtc/Makefile
Stefan Roese [Sat, 8 Dec 2007 13:47:34 +0000 (14:47 +0100)]
ppc4xx: 405EX: Correctly enable USB pins
This patch selects the USB data pins in the 405EX GPIO and MFC (multi
function control) registers. This is done for the AMCC Kilauea and
Makalu eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Sat, 8 Dec 2007 07:25:09 +0000 (08:25 +0100)]
CFI: Coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
Michael Schwingen [Fri, 7 Dec 2007 22:35:02 +0000 (23:35 +0100)]
CFI: support JEDEC flash roms in CFI-flash framework
The following patch adds support for non-CFI flash ROMS, by hooking into the
CFI flash code and using most of its code, as recently discussed here in the
thread "Mixing CFI and non-CFI flashs".
Signed-off-by: Michael Schwingen <michael@schwingen.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Gerald Van Baren [Thu, 29 Nov 2007 02:24:50 +0000 (21:24 -0500)]
Conditionally compile fdt_fixup_ethernet()
Fix compiler warnings: On boards that don't have ethernets defined,
don't compile fdt_fixup_ethernet().
Kumar Gala [Wed, 28 Nov 2007 03:59:46 +0000 (21:59 -0600)]
Convert boards that set memory node to use fdt_fixup_memory()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 23:06:15 +0000 (17:06 -0600)]
Added fdt_fixup_stdout that uses aliases to set linux,stdout-path
We use a combination of the serialN alias and CONFIG_CONS_INDEX to
determine which serial alias we should set linux,stdout-path to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 20:57:45 +0000 (14:57 -0600)]
Add common memory fixup function
Add the function fdt_fixup_memory() to fixup the /memory node of the fdt
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 17:19:12 +0000 (11:19 -0600)]
Conditionally compile fdt_support.c
Modify common/Makefile to conditionally compile fdt_support.c based
on CONFIG_OF_LIBFDT.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Mon, 26 Nov 2007 16:41:40 +0000 (10:41 -0600)]
Fix build breakage due to libfdt import
The IDS8247 got lost in the update and need an API update
do to rename of functions in libfdt.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Gerald Van Baren [Sat, 24 Nov 2007 00:43:20 +0000 (19:43 -0500)]
Add spaces around the = in the fdt print format.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Jon Loeliger [Thu, 6 Dec 2007 17:27:32 +0000 (11:27 -0600)]
Merge commit 'wd/master'
Nobuhiro Iwamatsu [Thu, 6 Dec 2007 16:25:38 +0000 (01:25 +0900)]
sh: Moved driver of the SuperH dependence
The composition of the directory in the drivers/ changed.
I moved SuperH serial driver and marubun PCMCIA driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Thu, 6 Dec 2007 16:20:25 +0000 (01:20 +0900)]
Merge git://www.denx.de/git/u-boot
Nobuhiro Iwamatsu [Thu, 6 Dec 2007 16:20:16 +0000 (01:20 +0900)]
Merge git://www.denx.de/git/u-boot
Conflicts:
drivers/Makefile
Wolfgang Denk [Thu, 6 Dec 2007 09:21:19 +0000 (10:21 +0100)]
Release v1.3.1
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Thu, 6 Dec 2007 09:21:03 +0000 (10:21 +0100)]
ADS5121 Board: fix compile problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Stefan Roese [Thu, 6 Dec 2007 04:58:43 +0000 (05:58 +0100)]
ppc4xx: Enable hardware-fix for PCI/DMA errata on AMCC 440SP/SPe boards
This patch enables the hardware-fix for the PCI/DMA errata's 19+22 by
setting the FIXD bit in the SDR0_MFR register. Here a description of the
symptoms:
Problem Description
------------------------------
If a DMA is performed between memory and PCI with the DMA 1 Controller
using prefetch, and as a result uses a special purpose buffer selected by
the PCIXn Bridge Options 1 Register (PCIXn_BRDGOPT1[RBP7] - bits 31-29),
the first part of the transfer sequence is performed twice. The
PPC440SPe PCI Controller requests more data than was needed such that in
the case of enforce memory protection, a host CPU exception can occur.
No data is corrupted, because data transfer is stopped in the PCI
Controller. Prefetch enable is specified by setting DMA Configuration
Register (I2O0_DMAx_CFG[DXEPD] - bit 31) to 0.
Behavior that may be observed in a running system
---------------------------------------------------------------------------
1. DMA performance is decreased because of the double access on the PCI bus
interface.
2. If an illegal access to some address on the PCI bus is detected at the
system level, a machine check or similar system error may occur.
Workarounds Available
----------------------------------
1. Do not program prefetch. Note that a prefetch command cannot be programmed
without selecting a special purpose buffer.
2. To avoid crossing a physical boundary of the PCI slave device, add 512
bytes of address to the PCI address range.
This patch was originally provided by Pravin M. Bathija <pbathija@amcc.com>
from AMCC and slighly changed.
Signed-off-by: Pravin M. Bathija <pbathija@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Tue, 4 Dec 2007 15:29:48 +0000 (16:29 +0100)]
ppc4xx: Yosemite/Yellowstone: Add DTT AD7414 support
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Sun, 2 Dec 2007 23:15:28 +0000 (00:15 +0100)]
Prepare for 1.3.1-rc1
Signed-off-by: Wolfgang Denk <wd@denx.de>
Stefan Roese [Fri, 30 Nov 2007 06:15:41 +0000 (07:15 +0100)]
ppc4xx: Kilauea: Add PCIe reset assertion upon power-up
This manual PCIe reset triggering solves the problem seen with the
Intel EPRO/1000 card, which was not detected (link not established)
upon power-up reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Nobuhiro Iwamatsu [Wed, 28 Nov 2007 16:21:54 +0000 (01:21 +0900)]
sh: Add SuperH boards maintainer to MAINTAINERS file
Add MS7750SE and MS7722SE's board maintainer to MAINTAINERS file.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 28 Nov 2007 15:13:04 +0000 (00:13 +0900)]
sh: Add ms7750se support in MAKEALL
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 27 Nov 2007 08:44:53 +0000 (09:44 +0100)]
sh: Add sh3 and sh4 support in MAKEALL
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 24 Nov 2007 17:51:17 +0000 (02:51 +0900)]
sh: Add document for SuperH.
This document is a summary of information concerning SuperH of U-Boot.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 24 Nov 2007 17:39:31 +0000 (02:39 +0900)]
sh: Add marubun's pcmcia driver
Marubun pcmcia is a chip for PCMCIA used with SuperH.
Of course, this can be used even by other architectures.
When use this driver, came to be able to use CompactFlash
and Ethernet.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Sat, 24 Nov 2007 17:32:13 +0000 (02:32 +0900)]
sh: Update SuperH SCIF driver
- Changed volatile unsigned to vu_.
- Changed Makefile for kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Nobuhiro Iwamatsu [Wed, 28 Nov 2007 15:56:37 +0000 (00:56 +0900)]
Merge git://www.denx.de/git/u-boot
Conflicts:
drivers/Makefile
Jon Loeliger [Tue, 27 Nov 2007 17:15:26 +0000 (11:15 -0600)]
Merge commit 'wd/master'
Stefan Roese [Tue, 27 Nov 2007 10:57:35 +0000 (11:57 +0100)]
ppc4xx: Kilauea & Makalu: Fix ext IRQ pin multiplexing
After an error in the AMCC 405EX users manual now correctly configure
IRQ2 (Kilauea)/IRQ0 (Makalu) as alternate 2 signal for external IRQ
usage.
Signed-off-by: Stefan Roese <sr@denx.de>
Wolfgang Denk [Mon, 26 Nov 2007 21:57:53 +0000 (22:57 +0100)]
Merge commit '3deca9d'
Conflicts:
Makefile
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Mon, 26 Nov 2007 18:18:21 +0000 (19:18 +0100)]
Cleanup coding style; update CHANGELOG
Signed-off-by: Wolfgang Denk <wd@denx.de>
Wolfgang Denk [Mon, 26 Nov 2007 18:15:04 +0000 (19:15 +0100)]
Merge commit '87ddedd'
Jean-Christophe PLAGNIOL-VILLARD [Sun, 25 Nov 2007 21:39:25 +0000 (22:39 +0100)]
MAKEALL: add missing 512x boards in ppc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 25 Nov 2007 17:45:47 +0000 (18:45 +0100)]
Makefile : fix tags ctags etags with new drivers organization
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Stefan Roese [Mon, 26 Nov 2007 14:06:14 +0000 (15:06 +0100)]
ppc4xx: Makalu: Change EBC setup for CS0 to enable 400MHz usage
As suggested by Senao, use a different EBC_PB0AP setup for 400MHz
operation.
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan Roese [Mon, 26 Nov 2007 14:01:45 +0000 (15:01 +0100)]
ppc4xx: Kilauea: Configure pin mux to use ext IRQ2 as interrupt
Signed-off-by: Stefan Roese <sr@denx.de>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 25 Nov 2007 17:45:47 +0000 (18:45 +0100)]
Makefile : fix tags ctags etags with new drivers organization
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 20:26:56 +0000 (21:26 +0100)]
drivers/mtd : move mtd drivers to drivers/mtd
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 20:17:55 +0000 (21:17 +0100)]
drivers/misc : move misc drivers to drivers/misc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 20:13:59 +0000 (21:13 +0100)]
drivers/block : move block drivers to drivers/block
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 19:59:50 +0000 (20:59 +0100)]
drivers/rtc : move rtc drivers to drivers/rtc
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 19:14:44 +0000 (20:14 +0100)]
drivers/hwmon : move hardware monitor drviers to drivers/hwmon
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 18:46:45 +0000 (19:46 +0100)]
drivers/input : move input drivers to drivers/input
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 18:40:11 +0000 (19:40 +0100)]
drivers/usb : move usb drivers to drivers/usb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Sat, 24 Nov 2007 18:33:38 +0000 (19:33 +0100)]
drivers/serial : move serial drivers to drivers/serial
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Wed, 21 Nov 2007 20:19:24 +0000 (21:19 +0100)]
drivers/net : move net drivers to drivers/net
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:41:48 +0000 (20:41 +0100)]
drivers/video : move video drivers to drivers/video
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:33:09 +0000 (20:33 +0100)]
drivers/pcmcia : move pcmcia drivers to drivers/pcmcia
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Jean-Christophe PLAGNIOL-VILLARD [Tue, 20 Nov 2007 19:28:09 +0000 (20:28 +0100)]
drivers/pci : move pci drivers to drivers/pci
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Wolfgang Denk [Thu, 22 Nov 2007 23:55:23 +0000 (00:55 +0100)]
Merge branch 'testing' of git://denx.de/git/u-boot-fdt
Gerald Van Baren [Thu, 22 Nov 2007 22:23:23 +0000 (17:23 -0500)]
Fix fdt printing for updated libfdt
Also improve printing (adopt dtc v1 "c style" hex format), whitespace cleanup.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Kumar Gala [Wed, 21 Nov 2007 19:30:15 +0000 (13:30 -0600)]
Add additional fdt fixup helper functions
Added the following fdt fixup helpers:
* do_fixup_by_prop{_u32} - Find matching nodes by property name/value
* do_fixup_by_compat{_u32} - Find matching nodes by compat
The _u32 variants work the same only the property they are setting
is know to be a 32-bit integer instead of a byte buffer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 21 Nov 2007 17:11:03 +0000 (11:11 -0600)]
Add fdt_fixup_ethernet helper to set mac addresses
Added a fixup helper that uses aliases to set mac addresses
in the device tree based on the bd_t
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 21 Nov 2007 20:07:46 +0000 (14:07 -0600)]
Fix warnings from import of libfdt
cmd_fdt.c: In function fdt_print:
cmd_fdt.c:586: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:613: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:635: warning: assignment discards qualifiers from pointer target type
cmd_fdt.c:636: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 24 Oct 2007 16:04:22 +0000 (11:04 -0500)]
Update libfdt from device tree compiler (dtc)
Update libfdt to commit
8eaf5e358366017aa2e846c5038d1aa19958314e from
the device tree compiler (dtc) project.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Sun, 4 Nov 2007 00:46:28 +0000 (19:46 -0500)]
Move do_fixup* for libfdt into common code
Moved the generic fixup handling code out of cpu/mpc5xxx and cpu/mpc8260
into common/fdt_support.c and renamed:
do_fixup() -> do_fixup_by_path()
do_fixup_u32() -> do_fixup_by_path_u32()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Thu, 25 Oct 2007 21:15:07 +0000 (16:15 -0500)]
Make no options to fdt print default to '/'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Kumar Gala [Wed, 24 Oct 2007 15:21:57 +0000 (10:21 -0500)]
Removed some nonused fdt functions and moved fdt_find_and_setprop out of libfdt
Removed:
fdt_node_is_compatible
fdt_find_node_by_type
fdt_find_compatible_node
To ease merge of newer libfdt as we aren't using them anywhere at this time.
Also moved fdt_find_and_setprop out of libfdt into fdt_support.c for the same
reason.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Wed, 21 Nov 2007 16:19:37 +0000 (09:19 -0700)]
[BUILD] Remove libraries when updating autoconf.mk
Fix library problems caused by conditional compilation. Using
autoconf.mk to decide which files to compile has caused a problem when
changing configuration from one board to another without clearing out
the library (*.a) files.
It used to be that the linker was always passed the same list of .o
files when building the .a files. However, that is not longer true
with conditional compilation. Now, a different board config will have
a different file list passed to the linker. The problem occurs when
a library has already been built and the board config is changed.
Since the linker will update instead of replace a preexisting library,
then if the file list changes to remove some object files the old
objects will still exist in the library.
The solution is to remove all old library files when autoconf.mk is
made.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Kumar Gala [Wed, 21 Nov 2007 14:49:50 +0000 (08:49 -0600)]
[BUILD] conditionally compile libfdt/*.c in libfdt/Makefile
Modify libfdt/Makefile to conditionally compile the *.c files based
on the board config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Grant Likely [Mon, 24 Sep 2007 15:05:31 +0000 (09:05 -0600)]
[BUILD] conditionally compile common/cmd_*.c in common/Makefile
Modify common/Makefile to conditionally compile the cmd_*.c files based
on the board config.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Grant Likely [Mon, 24 Sep 2007 15:05:31 +0000 (09:05 -0600)]
[BUILD] Generate include/autoconf.mk from board config files
Use cpp and sed to postprocess config.h and import the defined values
into include/autoconf.mk. autoconf.mk is then included by config.mk to
give 'make' access to the board configuration.
Doing this enables conditional compilation at the Makefile level instead
of by wrapping every .c file with #ifdef/#endif wrappers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jon Loeliger [Tue, 20 Nov 2007 21:02:26 +0000 (15:02 -0600)]
8610HPCD: Enable the 8610 Display Interface Unit
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Jon Loeliger [Tue, 20 Nov 2007 21:00:53 +0000 (15:00 -0600)]
Move 8610 DIU interface structure definitions to header file.
These two structures are still needed during the
initialization and setup of the DIU hardware.
So move them to the fsl_diu_fb.h file for now.
Official "blah".
Noticed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Jon Loeliger [Tue, 20 Nov 2007 20:34:57 +0000 (14:34 -0600)]
Merge commit 'remotes/wd/master'
projects / platform / kernel / u-boot.git / log