Masahiro Yamada [Wed, 10 Aug 2016 07:08:45 +0000 (16:08 +0900)]
ARM: uniphier: move (and rename) CONFIG_UNIPHIER_L2CACHE_ON to Kconfig
Move this option to Kconfig, renaming it into CONFIG_CACHE_UNIPHIER.
The new option name makes sense enough, and the same as Linux has.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:44 +0000 (16:08 +0900)]
ARM: uniphier: move outer cache register macros to .c file
Now, all of these macros are only used in cache-uniphier.c, so
there is no need to export them in a header file.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:43 +0000 (16:08 +0900)]
ARM: uniphier: reuse uniphier_cache_disable() for lowlevel_init
The DRAM is available at this point, so setup the temporary stack
and call the C function to reduce the code duplication a bit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:42 +0000 (16:08 +0900)]
ARM: uniphier: export uniphier_cache_enable/disable functions
The System Cache (outer cache) is used not only as L2 cache,
but also as locked SRAM. The functions for turning on/off it
is necessary whether the L2 cache is enabled or not.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:41 +0000 (16:08 +0900)]
ARM: uniphier: move lowlevel debug init code after page table switch
As the sLD3 Boot ROM has a complex page table, it is difficult to
set up the debug UART with enabling it. It will be much easier to
initialize the UART port after switching over to the straight-mapped
page table.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:40 +0000 (16:08 +0900)]
ARM: uniphier: fix ROM boot mode for PH1-sLD3
Commit
4b50369fb535 ("ARM: uniphier: create early page table at
run-time") broke the ROM boot mode for PH1-sLD3 SoC, because the
run-time page table creation requires the outer cache register
access but the page table in the sLD3 Boot ROM does not straight-map
virtual/physical addresses.
The idea here is to check the current page table to determine if
it is a straight map table. If not, adjust the outer cache register
base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:39 +0000 (16:08 +0900)]
ARM: uniphier: refactor L2 zero-touching code in lowlevel_init
Here, the ldr pseudo-instruction falls into the ldr + data set.
The register access by [r1, #offset] produces shorter code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:38 +0000 (16:08 +0900)]
ARM: uniphier: do not compile v7_outer_cache_disable if L2 is disabled
If CONFIG_UNIPHIER_L2CACHE_ON is undefined, the L2 cache is never
enabled, so there is no need for v7_outer_cache_disable(). The weak
stub avoids the compile error anyway.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:37 +0000 (16:08 +0900)]
ARM: uniphier: support prefetch and touch operations for outer cache
The UniPhier outer cache (L2 cache on ARMv7 SoCs) can be used as
SRAM by locking ways.
These functions will be used to transfer the trampoline code for SMP
into the locked SRAM.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Wed, 10 Aug 2016 07:08:36 +0000 (16:08 +0900)]
ARM: uniphier: refactor outer cache code
Unify the range/all operation routines into the common function,
uniphier_cache_maint_common(), and sync code with Linux a bit more.
This reduces the code duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Tue, 9 Aug 2016 11:16:01 +0000 (07:16 -0400)]
Merge git://www.denx.de/git/u-boot-ppc4xx
Dirk Eibach [Mon, 1 Aug 2016 14:34:49 +0000 (16:34 +0200)]
ppc4xx: Fix platform support
Commit "ecc3066 Fix board init code to respect the C runtime environment"
broke platform support for ppc4xx.
start.S prepares a stackframe that is later rendered unusable by appending
the reserved space for global data.
Instead the reserved space has to be put first. Then the stackframe can
be pushed.
I can only test the 405EP OCM case. At least all other ppc4xx boards still
build.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Vignesh R [Mon, 25 Jul 2016 10:56:45 +0000 (16:26 +0530)]
i2c: i2c-uclass-compat: avoid any BSS usage
As I2C can be used before DRAM initialization for reading EEPROM,
avoid using static variables stored in BSS, since BSS is in DRAM, which
may not have been initialised yet. Explicitly mark "static global"
variables as belonging to the .data section.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Heiko Schocher<hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alexander Graf [Fri, 5 Aug 2016 12:51:47 +0000 (14:51 +0200)]
efi_loader: disk: Sanitize exposed devices
When a target device is 0 bytes long, there's no point in exposing it to
the user. Let's just skip them.
Also, when an offset is passed into the efi disk creation, we should
remove this offset from the total number of sectors we can handle.
This patch fixes both things.
Signed-off-by: Alexander Graf <agraf@suse.de>
Alexander Graf [Fri, 5 Aug 2016 12:49:53 +0000 (14:49 +0200)]
efi_loader: disk: Fix CONFIG_BLK breakage
When using CONFIG_BLK, there were 2 issues:
1) The name we generate the device with has to match the
name we set in efi_set_bootdev()
2) The device we pass into our block functions was wrong,
we should not rediscover it but just use the already known
pointer.
This patch fixes both issues.
Signed-off-by: Alexander Graf <agraf@suse.de>
Simon Glass [Fri, 5 Aug 2016 03:58:14 +0000 (21:58 -0600)]
tiny-printf: Adjust to avoid using data section
We can pass all the variables down to the functions that need them, and
then everything is on the stack. This is safer than using the data section.
At least on firefly-rk3288, the code size is the same and the data size is
12 bytes smaller:
before:
18865 2636 40 21541 5425 b/firefly-rk3288/spl/u-boot-spl
after:
18865 2624 40 21529 5419 b/firefly-rk3288/spl/u-boot-spl
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Mugunthan V N [Tue, 2 Aug 2016 06:31:15 +0000 (12:01 +0530)]
configs: k2l_evm: add random eth address support
There is only one ethernet mac address in e-fuse, but there are
multiple slaves in keystone net, so enable random mac address
support.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 2 Aug 2016 06:31:14 +0000 (12:01 +0530)]
configs: k2e_evm: add random eth address support
There is only one ethernet mac address in e-fuse, but there are
multiple slaves in keystone net, so enable random mac address
support.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 2 Aug 2016 06:31:13 +0000 (12:01 +0530)]
configs: k2hk_evm: add random eth address support
There is only one ethernet mac address in e-fuse, but there are
multiple slaves in keystone net, so enable random mac address
support.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 2 Aug 2016 06:31:12 +0000 (12:01 +0530)]
drivers: net: keystone_net: add support for multi slave ethernet
Keystone net can have multiple ethernet slaves, currently only
slave 1 is supported by the driver. Register multiple slaves as
individual ethernets to network framework.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Mugunthan V N [Tue, 2 Aug 2016 06:31:11 +0000 (12:01 +0530)]
drivers: net: keystone_net: fix line termination with semi-colon
Each line should be terminated by semi-colon. It was not caught
earlier as there is a proper statement. Fix it by changing the
comma with semi-colon.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Vignesh R [Tue, 2 Aug 2016 04:44:28 +0000 (10:14 +0530)]
ARM: dts: dra72-evm: Add mode-gpios entry for mac node
On DRA72 EVM, cpsw slave1 is muxed with VIN2A, hence switch to cpsw
slave0 for ethernet. This is controlled by pcf gpio line. Add
appropriate mode-gpios DT entry so that driver can select the required
slave.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Tue, 2 Aug 2016 04:44:27 +0000 (10:14 +0530)]
net: cpsw: Add support to drive gpios for ethernet to be functional
On DRA72 EVM, cpsw slaves may be muxed with other modules. This
selection is controlled by a pcf gpio line. Add support for cpsw driver
to acquire mode-gpios and select the appropriate slave using gpio APIs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Vignesh R [Tue, 2 Aug 2016 04:44:26 +0000 (10:14 +0530)]
ARM: dts: dra7xx: Add u-boot specific property for PCF8575 nodes
PCF8575 does not have any registers hence, offset field needs to be
ignored for i2c read/write. Therefore populate u-boot,i2c-offset-len
with 0 in PCF8575 DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Vignesh R [Tue, 2 Aug 2016 04:44:25 +0000 (10:14 +0530)]
ARM: dra7xx_evm: Enable support for TI PCF8575
On DRA7, pcf chip present at address 0x21 on i2c1, is used to
switch between cpsw slave0 and slave1. Hence, enable PCF
driver for the same.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Vignesh R [Tue, 2 Aug 2016 04:44:24 +0000 (10:14 +0530)]
gpio: Add driver for TI PCF8575 I2C GPIO expander
TI's PCF8575 is a 16-bit I2C GPIO expander.The device features a
16-bit quasi-bidirectional I/O ports. Each quasi-bidirectional I/O can
be used as an input or output without the use of a data-direction
control signal. The I/Os should be high before being used as inputs.
Read the device documentation for more details[1].
This driver is based on pcf857x driver available in Linux v4.7 kernel.
It supports basic reading and writing of gpio pins.
[1] http://www.ti.com/lit/ds/symlink/pcf8575.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Mike Looijmans [Tue, 26 Jul 2016 05:34:07 +0000 (07:34 +0200)]
spl_nor.c: Support devicetree sizes different from 16k
The devicetrees for various platforms already exceed 16k. Add a define
CONFIG_SYS_FDT_SIZE to specify the FDT size, and set to 16k for the
two boards that define this CONFIG_SYS_FDT_BASE parameter. This
allows platforms with larger devicetree blobs to boot from NOR.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Chin Liang See [Sun, 7 Aug 2016 14:50:40 +0000 (22:50 +0800)]
spi: cadence_qspi_apb: Ensure baudrate doesn't exceed max value
Ensuring the baudrate divisor value doesn't exceed the max value
in the calculation.It will be capped at max value to ensure the
correct value being written into the register.
Example of the existing bug is when calculated div = 16. After and
with the mask, the value written to register is actually 0 (register
field for baudrate divisor). With this fix, the value written is now
15 which is max value for baudrate divisor.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jteki@openedev.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Masahiro Yamada [Sun, 24 Jul 2016 16:38:53 +0000 (01:38 +0900)]
ARM: socfpga: use the default CONFIG_BOOTDELAY=2
This option controls how long it should be paused before entering
the auto-boot mode. The default value from Kconfig should be fine
except socfpga_vining_fpga_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tom Rini [Sat, 6 Aug 2016 15:38:14 +0000 (11:38 -0400)]
Merge git://git.denx.de/u-boot-rockchip
Tom Rini [Fri, 5 Aug 2016 21:34:55 +0000 (17:34 -0400)]
zynq_sdhci.c: Fix warning in arasan_sdhci_probe
We no longer need to set 'caps' as it's not passed to sdhci_setup_cfg
anymore.
Fixes:
14bed52d276a ("mmc: sdhci: remove the unnecessary arguments for
sdhci_setup_cfg")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 5 Aug 2016 18:09:15 +0000 (14:09 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-tegra
Tom Rini [Fri, 5 Aug 2016 13:15:55 +0000 (09:15 -0400)]
Merge branch 'master' of git://git.denx.de/u-boot-mmc
Karl Beldan [Tue, 2 Aug 2016 10:36:17 +0000 (10:36 +0000)]
configs: Fix mmc rescan misuses
This follows
9fd383724cf4 ("mmc: don't allow extra cmdline arguments"),
and affects omapl138_lcdk and omap3_evm_quick_mmc.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Karl Beldan [Tue, 2 Aug 2016 18:57:14 +0000 (18:57 +0000)]
mkimage: Fix argument parsing with signature comment
Inform getopt that '-c' requires a parameter.
Fixes:
a02221f29deb ("mkimage: Convert to use getopt()")
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Glass [Sun, 31 Jul 2016 23:35:09 +0000 (17:35 -0600)]
test: Adjust run_command_list() to return a list of strings
Return one string for each command that was executed. This seems cleaner.
Suggested-by: Teddy Reed <teddy.reed@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Sun, 31 Jul 2016 23:35:08 +0000 (17:35 -0600)]
test: Add a function to restart U-Boot
Add a proper function for this rather than using internal functions. Use it
in the single call site.
Also, do a restart at the end of the vboot test to reset to the normal
device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Stephen Warren <swarren@nvidia.com>
Simon Glass [Sun, 31 Jul 2016 23:35:07 +0000 (17:35 -0600)]
test: vboot: Put each test variant in its own section
Use 'cons.log.section' feature to split up the test output. This makes it
easier to read.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 31 Jul 2016 23:35:06 +0000 (17:35 -0600)]
test: Rename sha to sha_algo and pass it around
Rename this argument and pass it to each function that needs it, instead of
making it global.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Suggested-by: Teddy Reed <teddy.reed@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 31 Jul 2016 23:35:05 +0000 (17:35 -0600)]
test: Drop the cmd() function
Instead of this, use the existing run_and_log() function, enhanced to
support a command string as well as a list of arguments.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 31 Jul 2016 23:35:04 +0000 (17:35 -0600)]
test: Fix typos in comments
Fix some typos in various files introduced with the vboot test conversion.
Reported-by: Teddy Reed <teddy.reed@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 31 Jul 2016 23:35:03 +0000 (17:35 -0600)]
test: Check exit status in run_and_log_expect_exception()
This check was missed. Add it and make the message more verbose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes:
9e17b034 (test/py: Provide a way to check that a command fails)
Simon Glass [Sun, 31 Jul 2016 23:35:02 +0000 (17:35 -0600)]
test: Fix typos and tidy up
Fix review comments that were missed at the time. Also explain why we need
to regenerate the device tree for each test.
Reported-by: Teddy Reed <teddy.reed@gmail.com>
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes:
f6349c3c (test: Add a README)
Simon Glass [Sun, 31 Jul 2016 23:35:01 +0000 (17:35 -0600)]
Makefile: Allow 'make tests' to run tests
Add this shortcut for running tests. Unfortunately 'make test' cannot be
used as it is an existing directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Teddy Reed <teddy.reed@gmail.com>
Alexander Graf [Sat, 30 Jul 2016 21:13:03 +0000 (23:13 +0200)]
armv8: mmu: Detect page table overflow in emergency pt creation
We create 2 sets of page tables: One for normal operation, one for
emergency (used while modifying the former).
Because the page tables grow dynamically, we have code that checks
for overflow. Unfortunately we didn't adjust the available space
variable while creating the emergency tables, so potentially someone
might run into an overflow there (not seen in real world yet though!).
Fix it by properly adjusting the size as well as the base offset in
emergency page table creation.
Reported-by: York Sun <york.sun@nxp.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Kever Yang [Fri, 29 Jul 2016 03:12:18 +0000 (11:12 +0800)]
cmd: gpt: fix the wrong size parse for the last partition
The calculation of "dev_desc->lba - 34 - 1 - offset" is not correct for
size '-', because both fist_usable_lba and last_usable_lba will remain
34 sectors.
We can simply use 0 for size '-' because the part_efi module will decode
the size and auto extend the size to maximum available size.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tom Rini [Thu, 28 Jul 2016 02:29:42 +0000 (22:29 -0400)]
omap3: Drop omap3_evm_quick_* targets
These config targets were added well before the Kconfig migration began
as a way to demonstrate how to make these platforms work with cut down
features. At this point in time they no longer serve a good purpose so
remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
Heiko Stübner [Fri, 22 Jul 2016 21:51:06 +0000 (23:51 +0200)]
rockchip: remove log2 reimplementation from clock drivers
The already available ilog2 function does exactly the same in the common
case than the log2 function the current clock-driver reimplement.
So, simply move to that one.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Thu, 4 Aug 2016 03:45:00 +0000 (11:45 +0800)]
config: rk3399: enable dwmmc controller
Enable the rockchip dwmmc driver for rk3399 and its evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Thu, 4 Aug 2016 03:44:59 +0000 (11:44 +0800)]
dts: rk3399: enable dwmmc for sdcard
rk3399 sdcard is using dwmmc controller, enable it for sdcard.
SCLK_SDMMC is the clock for controller operation clock, move it
to the first place.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Thu, 4 Aug 2016 03:44:58 +0000 (11:44 +0800)]
clock: rk3399: add support for dwmmc 400K
MMC core will use 400KHz for card initialize first and then switch to
higher frequency like 50MHz, we need to support both 400KHz and about
50MHz for dwmmc controller.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Kever Yang [Thu, 4 Aug 2016 03:40:29 +0000 (11:40 +0800)]
configs: rk3399: add gpt and fs support
To compatible with distro boot, we need to add gpt and fs support,
including gpt table and vfat, ext2, ext4 support.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Wed, 3 Aug 2016 03:55:06 +0000 (11:55 +0800)]
rockchip: add usb mass storage feature support for rk3288
Enable ums feature for rk3288 boards, so that we can mount the mmc
device to PC.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Wed, 3 Aug 2016 03:55:05 +0000 (11:55 +0800)]
rockchip: add basic partitions support for rk3288
For compatibility with distro boot, fastboot, and mount the mmc deivce
to PC via usb mass storage feature, GPT partitions are essential.
You should write the partitions to mmc device prior to use above
feature.
=> gpt write mmc 1 $partitions
GPT successfully written to block device!
success!
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Mon, 1 Aug 2016 00:46:19 +0000 (08:46 +0800)]
rockchip: add support for rk3288 miniarm board
Miniarm is a rockchip rk3288 based development board, which has lots of
interface such as HDMI, USB, micro-SD card, Audio etc.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Heiko Stübner [Fri, 29 Jul 2016 12:47:21 +0000 (14:47 +0200)]
move: rockchip: move clock drivers into a subdirectory
With the number of Rockchip clock drivers increasing, don't clutter up
the core drivers/clk directory with them and instead move them out of
the way into a separate subdirectory.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Simon Glass <sjg@chromium.org>
Updated for rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Kever Yang [Fri, 29 Jul 2016 02:35:25 +0000 (10:35 +0800)]
rk3399: add basic soc driver
This patch add driver for:
- clock driver including set_rate for cpu, mmc, vop, I2C.
- sysreset driver
- grf syscon driver
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Sandy Patterson [Thu, 28 Jul 2016 13:49:01 +0000 (09:49 -0400)]
rockchip: rockchip, sdram-channel 0xff fix remaining dts
Add an extra byte so that this data is not byteswapped.
Signed-off-by: Sandy Patterson <apatterson@sightlogix.com>
Acked-by: Simon Glass <sjg@chromium.org>
Xu Ziyuan [Thu, 28 Jul 2016 03:42:34 +0000 (11:42 +0800)]
rockchip: add fastboot support for rk3036 board
Enable fastboot feature on rk3036, please refer to doc/README.rockchip
for more detailed usage.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jaehoon Chung [Fri, 5 Aug 2016 05:13:36 +0000 (14:13 +0900)]
mmc: sdhci: fix the compiler warning when disable CONFIG_MMC_SDMA
When disabled CONFIG_MMC_SDMA, variable caps didn't use.
This patch fixes the compiler error for -Wunused-but-set-variable
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tom Rini [Thu, 28 Jul 2016 02:29:41 +0000 (22:29 -0400)]
omap3, omap4: Enable USE_TINY_PRINTF for all
In the case of omap3 we have a number of platforms that are close to
exceeding SRAM limits, depending on compiler. Move to USE_TINY_PRINTF
to give them more room. OMAP4 will soon enough be in a similar place,
so enable that now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 28 Jul 2016 02:29:40 +0000 (22:29 -0400)]
omap3: Move to select SUPPORT_SPL for all
In reality all omap3 platforms support SPL so move the select for this
up a level.
Signed-off-by: Tom Rini <trini@konsulko.com>
Max Filippov [Thu, 28 Jul 2016 00:57:24 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_std_bdinfo
print_std_bdinfo outputs typical set of board information entries:
boot params location, memory and flash addresses and sizes, network
interfaces information and configured serial baud rate.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Max Filippov [Thu, 28 Jul 2016 00:57:23 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_baudrate
print_baudrate outputs serial baud rate.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Max Filippov [Thu, 28 Jul 2016 00:57:22 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_eth_ip_addr
print_eth_ip_addr outputs eth configurations for up to 6 interfaces and
configured IP address.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Max Filippov [Thu, 28 Jul 2016 00:57:21 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_bi_flash
print_bi_flash outputs flashstart, flashsize and flashoffset lines.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Max Filippov [Thu, 28 Jul 2016 00:57:20 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_bi_dram
print_bi_dram outputs start address and size for each DRAM bank.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Max Filippov [Thu, 28 Jul 2016 00:57:19 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_bi_mem
print_bi_mem outputs memstart and memsize lines.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Max Filippov [Thu, 28 Jul 2016 00:57:18 +0000 (03:57 +0300)]
cmd/bdinfo: extract print_bi_boot_params
print_bi_boot_params outputs boot parameters structure location.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masahiro Yamada [Mon, 25 Jul 2016 10:56:03 +0000 (19:56 +0900)]
treewide: move CONFIG_PHYS_64BIT to Kconfig
We need to ensure that CONFIG_PHYS_64BIT is configured via Kconfig so
that it is always available to the build system. Otherwise we can run
into cases where we have inconsistent sizes of certain attributes.
Ravi Babu reported offset mismatch of struct dwc3 across files since
commit
95ebc253e6d4 ("types.h: move and redefine resource_size_t").
Since the commit, resource_addr_t points to phys_addr_t, whose size
is dependent on CONFIG_PHYS_64BIT for ARM architecture.
I tried my best to use "select" where possible (for example, ARMv8
architecture) because I think this kind of option is generally user-
unconfigurable. However, I see some of PowerPC boards have 36BIT
defconfigs as well as 32BIT ones. I moved CONFIG_PHYS_64BIT to the
defconfigs for such boards.
CONFIG_36BIT is no longer referenced, so all of the defines were
removed from CONFIG_SYS_EXTRA_OPTIONS.
Fixes:
95ebc253e6d4 ("types.h: move and redefine resource_size_t")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reported-by: Ravi Babu <ravibabu@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:29 +0000 (19:15 +0900)]
tools: moveconfig: support CONFIG_SYS_EXTRA_OPTIONS cleaning
We mostly move config options from board header files to Kconfig,
but sometimes config defines come from CONFIG_SYS_EXTRA_OPTIONS.
Historically, CONFIG_SYS_EXTRA_OPTIONS originates in boards.cfg,
which was used as a central database of configuration prior to the
Kconfig conversion.
Now, we want to migrate to primary entries in Kconfig rather than
option list in CONFIG_SYS_EXTRA_OPTIONS, so it should be helpful to
have the tool to cleanup CONFIG_SYS_EXTRA_OPTIONS automatically.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:28 +0000 (19:15 +0900)]
tools: moveconfig: make getting all defconfigs into helper function
I want to reuse this routine in the next commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:27 +0000 (19:15 +0900)]
tools: moveconfig: fix cleanup of defines across multiple lines
Correct the clean-up of such defines that continue across multiple
lines, like follows:
#define CONFIG_FOO "this continues to the next line " \
"this line should be removed too" \
"this line should be removed as well"
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:26 +0000 (19:15 +0900)]
tools: moveconfig: show diffs of cleaned headers in color
Show code diff in color if --color option is given.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:25 +0000 (19:15 +0900)]
tools: moveconfig: show result of header cleaning in unified diff
The header cleanup feature of this tool now removes empty ifdef's,
successive blank lines as well as moved option defines. So, we
want to see a little more context to check which lines were deleted.
It is true that we can see it by "git diff", but it would not work
in the --dry-run mode. So, here, this commit.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:24 +0000 (19:15 +0900)]
tools: moveconfig: trim garbage lines after header cleanups
The tools/moveconfig.py has a feature to cleanup #define/#undef's
of moved config options, but I want this tool to do a better job.
For example, when we are moving CONFIG_FOO and its define is
surrounded by #ifdef ... #endif, like follows:
#ifdef CONFIG_BAR
# define CONFIG_FOO
#endif
The header cleanup will leave empty #ifdef ... #endif:
#ifdef CONFIG_BAR
#endif
Likewise, if a define line between two blank lines
<blank line>
#define CONFIG_FOO
<blank lines.
... is deleted, the result of the clean-up will be successive empty
lines, which is a coding-style violation.
It is tedious to remove left-over garbage lines manually, so I want
the tool to take care of this. The tool's job is still not perfect,
so we should check the output of the tool, but I hope our life will
be much easier with this patch.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:23 +0000 (19:15 +0900)]
tools: moveconfig: do not check clean tree and compilers for -H option
The clean tree (make mrproper) and compilers are required when moving
config options, but not needed when we only cleanup headers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Masahiro Yamada [Mon, 25 Jul 2016 10:15:22 +0000 (19:15 +0900)]
tools: moveconfig: do not cleanup headers in include/generated
The files in include/generated are generated during build and removed
by "make mrproper", so it has no point to touch them by this tool.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Fri, 22 Jul 2016 21:59:11 +0000 (17:59 -0400)]
ext4: Refuse to mount filesystems with 64bit feature set
With e2fsprogs after 1.43 the 64bit and metadata_csum features are
enabled by default. The metadata_csum feature changes how
ext4_group_desc->bg_checksum is calculated, which would break write
support. The 64bit feature however introduces changes such that it
cannot be read by implementations that do not support it. Since we do
not support this, we must not mount it.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reported-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Mon, 1 Aug 2016 22:54:53 +0000 (18:54 -0400)]
ARM: Rework and correct barrier definitions
As part of testing booting Linux kernels on Rockchip devices, it was
discovered by Ziyuan Xu and Sandy Patterson that we had multiple and for
some cases incomplete isb definitions. This was causing a failure to
boot of the Linux kernel.
In order to solve this problem as well as cover any corner cases that we
may also have had a number of changes are made in order to consolidate
things. First, <asm/barriers.h> now becomes the source of isb/dsb/dmb
definitions. This however introduces another complexity. Due to
needing to build SPL for 32bit tegra with -march=armv4 we need to borrow
the __LINUX_ARM_ARCH__ logic from the Linux Kernel in a more complete
form. Move this from arch/arm/lib/Makefile to arch/arm/Makefile and add
a comment about it. Now that we can always know what the target CPU is
capable off we can get always do the correct thing for the barrier. The
final part of this is that need to be consistent everywhere and call
isb()/dsb()/dmb() and NOT call ISB/DSB/DMB in some cases and the
function names in others.
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Sandy Patterson <apatterson@sightlogix.com>
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reported-by: Sandy Patterson <apatterson@sightlogix.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Alexey Brodkin [Thu, 4 Aug 2016 12:00:35 +0000 (15:00 +0300)]
arc: Rename AXS101 board to more generic AXS10x
As of now we have 2 flavors of ARC SDP boards:
1) AXS101 - with ARC770 in ASIC
2) AXS103 - with ARC HS38 in FPGA
Both options share exactly the same base-board and only differ with
CPU-tiles in use. That means all peripherals are the same (they are
implemented in FPGA on the base-board) and so generic board could be
used for both.
While at it:
* Recreated defconfigs with savedefconfig
* In include/configs/axs10x.h numerical sizes replaced with
defines from linux/sizes.h for better readability.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Alexey Brodkin [Thu, 4 Aug 2016 11:35:01 +0000 (14:35 +0300)]
arc: Rename ARCangel4 board to nSIM
ARCangel was one of the main development boards back in the day but
now it's gone and replaced by other boards like ARC SDP.
But we also used to have simulation platform very similar to ARCangel4
in terms of CPU settings as well as basic IO like UART. Even though
ARCangel4 is long gone now we have a replacement for simulation which is
a plain or stand-alone nSIM and Free nSIM.
Note Free nSIM is available for download here:
https://www.synopsys.com/cgi-bin/dwarcnsim/req1.cgi
And while at it:
* Finally switch hex numerical values in nsim.h to defines from
include/linux/sizes.h
* Add defconfigs with ARC HS38 cores
* Recreated all defconfigs with savedefconfig
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Wed, 3 Aug 2016 17:44:39 +0000 (20:44 +0300)]
arc: No need in sections defined in sources with newer tools
Starting from arc-2016.03 GNU tools linker properly works with
symbols defined in linker script and so external declarations
are no longer required, dump them.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Thu, 4 Aug 2016 06:21:50 +0000 (09:21 +0300)]
arc: Update exception & interrupt handling for ARCv2
Initially IVT for ARCv2 was simply copypasted from ARCompact
with some selected fixes so basic stuff works.
Now we update it with more ARCv2 specific vectors like
* Software Interrupt
* Division by zero
* Data cache consistency error
* Misaligned access
Also normal interrupts are now implemented properly and extened to
all possible 240 items.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Alexey Brodkin [Wed, 3 Aug 2016 17:45:22 +0000 (20:45 +0300)]
arc: Add debug messages during relocation fixups
This might be useful to make sure relocation fixups really
happen. And since this info gets printed only in DEBUG
build it doesn't really hurt normal execution.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Jaehoon Chung [Thu, 28 Jul 2016 05:26:24 +0000 (14:26 +0900)]
mmc: dw_mmc: fix the wrong Mask bit boundary for fifo_count bit
According to DesignWare TRM, FIFO_COUNT is bit[29:17].
If get the correct fifo_count value, it has to use the FIFO_MASK
as 0x1FFF, not 0x1FF.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Xu Ziyuan [Thu, 28 Jul 2016 02:25:48 +0000 (10:25 +0800)]
mmc: dw_mmc: fix data starvation by host timeout under FIFO mode
This patch fixes data starvation by host timeout(HTO) error interrupt
which occurred under FIFO mode transfer on rk3036 board.
The former implement, the actual bytes were transmitted may be less than
should be. The size will still subtract value of len in case of there is
no receive/transmit FIFO data request interrupt.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Xu Ziyuan [Thu, 28 Jul 2016 02:25:47 +0000 (10:25 +0800)]
mmc: dw_mmc: transfer proper bytes to FIFO
The former implement, dw_mmc will push and pop the redundant data to
FIFO, we should transfer it according to the real size.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Tue, 26 Jul 2016 10:06:24 +0000 (19:06 +0900)]
mmc: sdhci: remove the unnecessary arguments for sdhci_setup_cfg
Some arguments don't need to pass to sdhci_setup_cfg.
Generic variable can be used in sdhci_setup_cfg, and some arguments are
already included in sdhci_host struct.
It's enough that just pass the board specific things to sdhci_setup_cfg().
After removing the unnecessary arguments, it's more simpler than before.
It doesn't consider "Version" and "Capabilities" anymore in each SoC
driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jaehoon Chung [Tue, 26 Jul 2016 10:06:23 +0000 (19:06 +0900)]
mmc: sdhci: remove the unused argument for sdhci_setup_cfg
buswidth isn't used anywhere in sdhci_setup_cfg.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jaehoon Chung [Tue, 26 Jul 2016 10:03:49 +0000 (19:03 +0900)]
mmc: sdhci: revert "mmc: sdhci: Claer high speed if not supported"
This "commit
429790026021d522d51617217d4b86218cca5750" is wrong.
SDHCI_QUIRK_NO_HISPD_BIT is for skipping to set CTRL_HISPD bit.
For example, Exynos didn't have CTRL_HISPD. But Highspeed mode
is supported.
(This quirks doesn't mean that driver didn't support the Highseepd mode.)
Note: If driver didn't support the Highspeed Mode, use or add the other
quirks.
After applied this patch, all Exynos SoCs are just running with 25MHz.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Xu Ziyuan [Sat, 23 Jul 2016 03:11:22 +0000 (11:11 +0800)]
mmc: display mmc list information like mmc_legacy type
It's nicer to see this:
=> mmc list
dwmmc@
ff0c0000: 0
dwmmc@
ff0f0000: 1 (eMMC)
than this:
=> mmc list
dwmmc@
ff0c0000: 0dwmmc@
ff0f0000: 1 (eMMC)
With the former, it's much clearer which mmc devices are on.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Jaehoon Chung [Tue, 19 Jul 2016 07:33:36 +0000 (16:33 +0900)]
mmc: use the generic error number
Use the generic error number instead of specific error number.
If use the generic error number, it can debug more easier.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Jaehoon Chung [Tue, 19 Jul 2016 07:33:35 +0000 (16:33 +0900)]
mmc: fsl_esdhc: remove the duplicated header file
"mmc.h" is already included. It's duplicated.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jaehoon Chung [Tue, 19 Jul 2016 07:33:34 +0000 (16:33 +0900)]
mmc: dw_mmc: remove the duplicated header file
<asm-generic/errno.h> is already included in <errno.h>.
It can use <errno.h> instead of <asm-generic/errno.h>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Jaehoon Chung [Tue, 12 Jul 2016 12:18:47 +0000 (21:18 +0900)]
mmc: s5p_sdhci: unset the SDHCI_QUIRK_BROKEN_R1B
Unset the SDHCI_QUIRK_BROKEN_R1B for exynos SoC.
(Tested on Exynos4 Boards.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Jaehoon Chung [Tue, 12 Jul 2016 12:18:46 +0000 (21:18 +0900)]
mmc: sdhci: set to INT_DATA_END when there are data
There is no data, it doesn't needs to wait for completing data transfer.
(It seems that it can be removed.)
Almost all timeout error is occured from stop command without data.
After applied this patch, I hope that we don't need to increase timeout value anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Masahiro Yamada [Sat, 9 Jul 2016 15:40:22 +0000 (00:40 +0900)]
mmc: sdhci: clean up timeout detection
The current timeout detection logic is not very nice; it calls
get_timer(start) in the while() loop, and then calls it again after
the loop to check if a timeout error happened.
Because of the time difference between the two calls of get_timer(),
the timeout detected after the loop may not be true.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Stephen Warren [Wed, 27 Jul 2016 21:24:57 +0000 (15:24 -0600)]
ARM: tegra: call tegra_board_init on Tegra186
Introduce tegra_board_init() and call it from board_init(). Tegra wil use
tegra_board_init() for board-specific initialization, and board_init() for
SoC-specific initialization.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Bryan Wu [Wed, 27 Jul 2016 21:48:21 +0000 (15:48 -0600)]
ARM: tegra: add I2C controllers to Tegra186 DT
Tegra186 has 8 I2C controllers including BPMP I2C. This patch adds the
other 7 generic controllers to Tegra186's DT.
Signed-off-by: Bryan Wu <pengw@nvidia.com>
(swarren, fixed DT node sort order, tweak patch description)
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>