hwmon: (lm90) Reduce maximum conversion rate for G781

[ Upstream commit a66c5ed539277b9f2363bbace0dba88b85b36c26 ]

According to its datasheet, G781 supports a maximum conversion rate value
of 8 (62.5 ms). However, chips labeled G781 and G780 were found to only
support a maximum conversion rate value of 7 (125 ms). On the other side,
chips labeled G781-1 and G784 were found to support a conversion rate value
of 8. There is no known means to distinguish G780 from G781 or G784; all
chips report the same manufacturer ID and chip revision.
Setting the conversion rate register value to 8 on chips not supporting
it causes unexpected behavior since the real conversion rate is set to 0
(16 seconds) if a value of 8 is written into the conversion rate register.
Limit the conversion rate register value to 7 for all G78x chips to avoid
the problem.

Fixes: ae544f64cc7b ("hwmon: (lm90) Add support for GMT G781")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ipv4: avoid using shared IP generator for connected sockets

commit 23f57406b82de51809d5812afd96f210f8b627f3 upstream.

ip_select_ident_segs() has been very conservative about using
the connected socket private generator only for packets with IP_DF
set, claiming it was needed for some VJ compression implementations.

As mentioned in this referenced document, this can be abused.
(Ref: Off-Path TCP Exploits of the Mixed IPID Assignment)

Before switching to pure random IPID generation and possibly hurt
some workloads, lets use the private inet socket generator.

Not only this will remove one vulnerability, this will also
improve performance of TCP flows using pmtudisc==IP_PMTUDISC_DONT

Fixes: 73f156a6e8c1 ("inetpeer: get rid of ip_id_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reported-by: Ray Che <xijiache@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ping: fix the sk_bound_dev_if match in ping_lookup

commit 2afc3b5a31f9edf3ef0f374f5d70610c79c93a42 upstream.

When 'ping' changes to use PING socket instead of RAW socket by:

   # sysctl -w net.ipv4.ping_group_range="0 100"

the selftests 'router_broadcast.sh' will fail, as such command

  # ip vrf exec vrf-h1 ping -I veth0 198.51.100.255 -b

can't receive the response skb by the PING socket. It's caused by mismatch
of sk_bound_dev_if and dif in ping_rcv() when looking up the PING socket,
as dif is vrf-h1 if dif's master was set to vrf-h1.

This patch is to fix this regression by also checking the sk_bound_dev_if
against sdif so that the packets can stil be received even if the socket
is not bound to the vrf device but to the real iif.

Fixes: c319b4d76b9e ("net: ipv4: add IPPROTO_ICMP socket kind")
Reported-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (lm90) Mark alert as broken for MAX6680

commit 94746b0ba479743355e0d3cc1cb9cfe3011fb8be upstream.

Experiments with MAX6680 and MAX6681 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.

Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

hwmon: (lm90) Mark alert as broken for MAX6646/6647/6649

commit f614629f9c1080dcc844a8430e3fb4c37ebbf05d upstream.

Experiments with MAX6646 and MAX6648 show that the alert function of those
chips is broken, similar to other chips supported by the lm90 driver.
Mark it accordingly.

Fixes: 4667bcb8d8fc ("hwmon: (lm90) Introduce chip parameter structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: fix information leakage in /proc/net/ptype

commit 47934e06b65637c88a762d9c98329ae6e3238888 upstream.

In one net namespace, after creating a packet socket without binding
it to a device, users in other net namespaces can observe the new
`packet_type` added by this packet socket by reading `/proc/net/ptype`
file. This is minor information leakage as packet socket is
namespace aware.

Add a net pointer in `packet_type` to keep the net namespace of
of corresponding packet socket. In `ptype_seq_show`, this net pointer
must be checked when it is not NULL.

Fixes: 2feb27dbe00c ("[NETNS]: Minor information leak via /proc/net/ptype file.")
Signed-off-by: Congyu Liu <liu3101@purdue.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ARM: 9170/1: fix panic when kasan and kprobe are enabled

commit 8b59b0a53c840921b625378f137e88adfa87647e upstream.

arm32 uses software to simulate the instruction replaced
by kprobe. some instructions may be simulated by constructing
assembly functions. therefore, before executing instruction
simulation, it is necessary to construct assembly function
execution environment in C language through binding registers.
after kasan is enabled, the register binding relationship will
be destroyed, resulting in instruction simulation errors and
causing kernel panic.

the kprobe emulate instruction function is distributed in three
files: actions-common.c actions-arm.c actions-thumb.c, so disable
KASAN when compiling these files.

for example, use kprobe insert on cap_capable+20 after kasan
enabled, the cap_capable assembly code is as follows:
<cap_capable>:
e92d47f0 push {r4, r5, r6, r7, r8, r9, sl, lr}
e1a05000 mov r5, r0
e280006c add r0, r0, #108    ; 0x6c
e1a04001 mov r4, r1
e1a06002 mov r6, r2
e59fa090 ldr sl, [pc, #144]  ;
ebfc7bf8 bl c03aa4b4 <__asan_load4>
e595706c ldr r7, [r5, #108]  ; 0x6c
e2859014 add r9, r5, #20
......
The emulate_ldr assembly code after enabling kasan is as follows:
c06f1384 <emulate_ldr>:
e92d47f0 push {r4, r5, r6, r7, r8, r9, sl, lr}
e282803c add r8, r2, #60     ; 0x3c
e1a05000 mov r5, r0
e7e37855 ubfx r7, r5, #16, #4
e1a00008 mov r0, r8
e1a09001 mov r9, r1
e1a04002 mov r4, r2
ebf35462 bl c03c6530 <__asan_load4>
e357000f cmp r7, #15
e7e36655 ubfx r6, r5, #12, #4
e205a00f and sl, r5, #15
0a000001 beq c06f13bc <emulate_ldr+0x38>
e0840107 add r0, r4, r7, lsl #2
ebf3545c bl c03c6530 <__asan_load4>
e084010a add r0, r4, sl, lsl #2
ebf3545a bl c03c6530 <__asan_load4>
e2890010 add r0, r9, #16
ebf35458 bl c03c6530 <__asan_load4>
e5990010 ldr r0, [r9, #16]
e12fff30 blx r0
e356000f cm r6, #15
1a000014 bne c06f1430 <emulate_ldr+0xac>
e1a06000 mov r6, r0
e2840040 add r0, r4, #64     ; 0x40
......

when running in emulate_ldr to simulate the ldr instruction, panic
occurred, and the log is as follows:
Unable to handle kernel NULL pointer dereference at virtual address
00000090
pgd = ecb46400
[00000090] *pgd=2e0fa003, *pmd=00000000
Internal error: Oops: 206 [#1] SMP ARM
PC is at cap_capable+0x14/0xb0
LR is at emulate_ldr+0x50/0xc0
psr: 600d0293 sp : ecd63af8  ip : 00000004  fp : c0a7c30c
r10: 00000000  r9 : c30897f4  r8 : ecd63cd4
r7 : 0000000f  r6 : 0000000a  r5 : e59fa090  r4 : ecd63c98
r3 : c06ae294  r2 : 00000000  r1 : b7611300  r0 : bf4ec008
Flags: nZCv  IRQs off  FIQs on  Mode SVC_32  ISA ARM  Segment user
Control: 32c5387d  Table: 2d546400  DAC: 55555555
Process bash (pid: 1643, stack limit = 0xecd60190)
(cap_capable) from (kprobe_handler+0x218/0x340)
(kprobe_handler) from (kprobe_trap_handler+0x24/0x48)
(kprobe_trap_handler) from (do_undefinstr+0x13c/0x364)
(do_undefinstr) from (__und_svc_finish+0x0/0x30)
(__und_svc_finish) from (cap_capable+0x18/0xb0)
(cap_capable) from (cap_vm_enough_memory+0x38/0x48)
(cap_vm_enough_memory) from
(security_vm_enough_memory_mm+0x48/0x6c)
(security_vm_enough_memory_mm) from
(copy_process.constprop.5+0x16b4/0x25c8)
(copy_process.constprop.5) from (_do_fork+0xe8/0x55c)
(_do_fork) from (SyS_clone+0x1c/0x24)
(SyS_clone) from (__sys_trace_return+0x0/0x10)
Code: 0050a0e1 6c0080e2 0140a0e1 0260a0e1 (f801f0e7)

Fixes: 35aa1df43283 ("ARM kprobes: instruction single-stepping support")
Fixes: 421015713b30 ("ARM: 9017/2: Enable KASan for ARM")
Signed-off-by: huangshaobo <huangshaobo6@huawei.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv6_tunnel: Rate limit warning messages

commit 6cee105e7f2ced596373951d9ea08dacc3883c68 upstream.

The warning messages can be invoked from the data path for every packet
transmitted through an ip6gre netdev, leading to high CPU utilization.

Fix that by rate limiting the messages.

Fixes: 09c6bbf090ec ("[IPV6]: Do mandatory IPv6 tunnel endpoint checks in realtime")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Tested-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: bnx2fc: Flush destroy_work queue before calling bnx2fc_interface_put()

commit 847f9ea4c5186fdb7b84297e3eeed9e340e83fce upstream.

The bnx2fc_destroy() functions are removing the interface before calling
destroy_work. This results multiple WARNings from sysfs_remove_group() as
the controller rport device attributes are removed too early.

Replace the fcoe_port's destroy_work queue. It's not needed.

The problem is easily reproducible with the following steps.

Example:

  $ dmesg -w &
  $ systemctl enable --now fcoe
  $ fipvlan -s -c ens2f1
  $ fcoeadm -d ens2f1.802
  [  583.464488] host2: libfc: Link down on port (7500a1)
  [  583.472651] bnx2fc: 7500a1 - rport not created Yet!!
  [  583.490468] ------------[ cut here ]------------
  [  583.538725] sysfs group 'power' not found for kobject 'rport-2:0-0'
  [  583.568814] WARNING: CPU: 3 PID: 192 at fs/sysfs/group.c:279 sysfs_remove_group+0x6f/0x80
  [  583.607130] Modules linked in: dm_service_time 8021q garp mrp stp llc bnx2fc cnic uio rpcsec_gss_krb5 auth_rpcgss nfsv4 ...
  [  583.942994] CPU: 3 PID: 192 Comm: kworker/3:2 Kdump: loaded Not tainted 5.14.0-39.el9.x86_64 #1
  [  583.984105] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013
  [  584.016535] Workqueue: fc_wq_2 fc_rport_final_delete [scsi_transport_fc]
  [  584.050691] RIP: 0010:sysfs_remove_group+0x6f/0x80
  [  584.074725] Code: ff 5b 48 89 ef 5d 41 5c e9 ee c0 ff ff 48 89 ef e8 f6 b8 ff ff eb d1 49 8b 14 24 48 8b 33 48 c7 c7 ...
  [  584.162586] RSP: 0018:ffffb567c15afdc0 EFLAGS: 00010282
  [  584.188225] RAX: 0000000000000000 RBX: ffffffff8eec4220 RCX: 0000000000000000
  [  584.221053] RDX: ffff8c1586ce84c0 RSI: ffff8c1586cd7cc0 RDI: ffff8c1586cd7cc0
  [  584.255089] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb567c15afc00
  [  584.287954] R10: ffffb567c15afbf8 R11: ffffffff8fbe7f28 R12: ffff8c1486326400
  [  584.322356] R13: ffff8c1486326480 R14: ffff8c1483a4a000 R15: 0000000000000004
  [  584.355379] FS:  0000000000000000(0000) GS:ffff8c1586cc0000(0000) knlGS:0000000000000000
  [  584.394419] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
  [  584.421123] CR2: 00007fe95a6f7840 CR3: 0000000107674002 CR4: 00000000000606e0
  [  584.454888] Call Trace:
  [  584.466108]  device_del+0xb2/0x3e0
  [  584.481701]  device_unregister+0x13/0x60
  [  584.501306]  bsg_unregister_queue+0x5b/0x80
  [  584.522029]  bsg_remove_queue+0x1c/0x40
  [  584.541884]  fc_rport_final_delete+0xf3/0x1d0 [scsi_transport_fc]
  [  584.573823]  process_one_work+0x1e3/0x3b0
  [  584.592396]  worker_thread+0x50/0x3b0
  [  584.609256]  ? rescuer_thread+0x370/0x370
  [  584.628877]  kthread+0x149/0x170
  [  584.643673]  ? set_kthread_struct+0x40/0x40
  [  584.662909]  ret_from_fork+0x22/0x30
  [  584.680002] ---[ end trace 53575ecefa942ece ]---

Link: https://lore.kernel.org/r/20220115040044.1013475-1-jmeneghi@redhat.com
Fixes: 0cbf32e1681d ("[SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks")
Tested-by: Guangwu Zhang <guazhang@redhat.com>
Co-developed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: elx: efct: Don't use GFP_KERNEL under spin lock

commit 61263b3a11a2594b4e898f166c31162236182b5c upstream.

GFP_KERNEL/GFP_DMA can't be used under a spin lock. According the comment,
els_ios_lock is used to protect els ios list so we can move down the spin
lock to avoid using this flag under the lock.

Link: https://lore.kernel.org/r/20220111012441.3232527-1-yangyingliang@huawei.com
Fixes: 8f406ef72859 ("scsi: elx: libefc: Extended link Service I/O handling")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: char: Fix race between the release of rpmsg_eptdev and cdev

commit 7a534ae89e34e9b51acb5a63dd0f88308178b46a upstream.

struct rpmsg_eptdev contains a struct cdev. The current code frees
the rpmsg_eptdev struct in rpmsg_eptdev_destroy(), but the cdev is
a managed object, therefore its release is not predictable and the
rpmsg_eptdev could be freed before the cdev is entirely released.

The cdev_device_add/del() API was created to address this issue
(see commit '233ed09d7fda ("chardev: add helper function to register
char devs with a struct device")'), use it instead of cdev add/del().

Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface")
Suggested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220110104706.v6.2.Idde68b05b88d4a2e6e54766c653f3a6d9e419ce6@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rpmsg: char: Fix race between the release of rpmsg_ctrldev and cdev

commit b7fb2dad571d1e21173c06cef0bced77b323990a upstream.

struct rpmsg_ctrldev contains a struct cdev. The current code frees
the rpmsg_ctrldev struct in rpmsg_ctrldev_release_device(), but the
cdev is a managed object, therefore its release is not predictable
and the rpmsg_ctrldev could be freed before the cdev is entirely
released, as in the backtrace below.

[   93.625603] ODEBUG: free active (active state 0) object type: timer_list hint: delayed_work_timer_fn+0x0/0x7c
[   93.636115] WARNING: CPU: 0 PID: 12 at lib/debugobjects.c:488 debug_print_object+0x13c/0x1b0
[   93.644799] Modules linked in: veth xt_cgroup xt_MASQUERADE rfcomm algif_hash algif_skcipher af_alg uinput ip6table_nat fuse uvcvideo videobuf2_vmalloc venus_enc venus_dec videobuf2_dma_contig hci_uart btandroid btqca snd_soc_rt5682_i2c bluetooth qcom_spmi_temp_alarm snd_soc_rt5682v
[   93.715175] CPU: 0 PID: 12 Comm: kworker/0:1 Tainted: G    B             5.4.163-lockdep #26
[   93.723855] Hardware name: Google Lazor (rev3 - 8) with LTE (DT)
[   93.730055] Workqueue: events kobject_delayed_cleanup
[   93.735271] pstate: 60c00009 (nZCv daif +PAN +UAO)
[   93.740216] pc : debug_print_object+0x13c/0x1b0
[   93.744890] lr : debug_print_object+0x13c/0x1b0
[   93.749555] sp : ffffffacf5bc7940
[   93.752978] x29: ffffffacf5bc7940 x28: dfffffd000000000
[   93.758448] x27: ffffffacdb11a800 x26: dfffffd000000000
[   93.763916] x25: ffffffd0734f856c x24: dfffffd000000000
[   93.769389] x23: 0000000000000000 x22: ffffffd0733c35b0
[   93.774860] x21: ffffffd0751994a0 x20: ffffffd075ec27c0
[   93.780338] x19: ffffffd075199100 x18: 00000000000276e0
[   93.785814] x17: 0000000000000000 x16: dfffffd000000000
[   93.791291] x15: ffffffffffffffff x14: 6e6968207473696c
[   93.796768] x13: 0000000000000000 x12: ffffffd075e2b000
[   93.802244] x11: 0000000000000001 x10: 0000000000000000
[   93.807723] x9 : d13400dff1921900 x8 : d13400dff1921900
[   93.813200] x7 : 0000000000000000 x6 : 0000000000000000
[   93.818676] x5 : 0000000000000080 x4 : 0000000000000000
[   93.824152] x3 : ffffffd0732a0fa4 x2 : 0000000000000001
[   93.829628] x1 : ffffffacf5bc7580 x0 : 0000000000000061
[   93.835104] Call trace:
[   93.837644]  debug_print_object+0x13c/0x1b0
[   93.841963]  __debug_check_no_obj_freed+0x25c/0x3c0
[   93.846987]  debug_check_no_obj_freed+0x18/0x20
[   93.851669]  slab_free_freelist_hook+0xbc/0x1e4
[   93.856346]  kfree+0xfc/0x2f4
[   93.859416]  rpmsg_ctrldev_release_device+0x78/0xb8
[   93.864445]  device_release+0x84/0x168
[   93.868310]  kobject_cleanup+0x12c/0x298
[   93.872356]  kobject_delayed_cleanup+0x10/0x18
[   93.876948]  process_one_work+0x578/0x92c
[   93.881086]  worker_thread+0x804/0xcf8
[   93.884963]  kthread+0x2a8/0x314
[   93.888303]  ret_from_fork+0x10/0x18

The cdev_device_add/del() API was created to address this issue (see
commit '233ed09d7fda ("chardev: add helper function to register char
devs with a struct device")'), use it instead of cdev add/del().

Fixes: c0cdc19f84a4 ("rpmsg: Driver for user space endpoint interface")
Signed-off-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220110104706.v6.1.Iaac908f3e3149a89190ce006ba166e2d3fd247a3@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: roles: fix include/linux/usb/role.h compile issue

commit 945c37ed564770c78dfe6b9f08bed57a1b4e60ef upstream.

when CONFIG_USB_ROLE_SWITCH is not defined,
add usb_role_switch_find_by_fwnode() definition which return NULL.

Fixes: c6919d5e0cd1 ("usb: roles: Add usb_role_switch_find_by_fwnode()")
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Link: https://lore.kernel.org/r/1641818608-25039-1-git-send-email-quic_linyyuan@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: fix unsigned stat widths

commit 3b8428b84539c78fdc8006c17ebd25afd4722d51 upstream.

Change i40e_update_vsi_stats and struct i40e_vsi to use u64 fields to match
the width of the stats counters in struct i40e_rx_queue_stats.

Update debugfs code to use the correct format specifier for u64.

Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Joe Damato <jdamato@fastly.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Fix for failed to init adminq while VF reset

commit 0f344c8129a5337dae50e31b817dd50a60ff238c upstream.

Fix for failed to init adminq: -53 while VF is resetting via MAC
address changing procedure.
Added sync module to avoid reading deadbeef value in reinit adminq
during software reset.
Without this patch it is possible to trigger VF reset procedure
during reinit adminq. This resulted in an incorrect reading of
value from the AQP registers and generated the -53 error.

Fixes: 5c3c48ac6bf5 ("i40e: implement virtual device interface")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Fix queues reservation for XDP

commit 92947844b8beee988c0ce17082b705c2f75f0742 upstream.

When XDP was configured on a system with large number of CPUs
and X722 NIC there was a call trace with NULL pointer dereference.

i40e 0000:87:00.0: failed to get tracking for 256 queues for VSI 0 err -12
i40e 0000:87:00.0: setup of MAIN VSI failed

BUG: kernel NULL pointer dereference, address: 0000000000000000
RIP: 0010:i40e_xdp+0xea/0x1b0 [i40e]
Call Trace:
? i40e_reconfig_rss_queues+0x130/0x130 [i40e]
dev_xdp_install+0x61/0xe0
dev_xdp_attach+0x18a/0x4c0
dev_change_xdp_fd+0x1e6/0x220
do_setlink+0x616/0x1030
? ahci_port_stop+0x80/0x80
? ata_qc_issue+0x107/0x1e0
? lock_timer_base+0x61/0x80
? __mod_timer+0x202/0x380
rtnl_setlink+0xe5/0x170
? bpf_lsm_binder_transaction+0x10/0x10
? security_capable+0x36/0x50
rtnetlink_rcv_msg+0x121/0x350
? rtnl_calcit.isra.0+0x100/0x100
netlink_rcv_skb+0x50/0xf0
netlink_unicast+0x1d3/0x2a0
netlink_sendmsg+0x22a/0x440
sock_sendmsg+0x5e/0x60
__sys_sendto+0xf0/0x160
? __sys_getsockname+0x7e/0xc0
? _copy_from_user+0x3c/0x80
? __sys_setsockopt+0xc8/0x1a0
__x64_sys_sendto+0x20/0x30
do_syscall_64+0x33/0x40
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f83fa7a39e0

This was caused by PF queue pile fragmentation due to
flow director VSI queue being placed right after main VSI.
Because of this main VSI was not able to resize its
queue allocation for XDP resulting in no queues allocated
for main VSI when XDP was turned on.

Fix this by always allocating last queue in PF queue pile
for a flow director VSI.

Fixes: 41c445ff0f48 ("i40e: main driver core")
Fixes: 74608d17fe29 ("i40e: add support for XDP_TX action")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Fix issue when maximum queues is exceeded

commit d701658a50a471591094b3eb3961b4926cc8f104 upstream.

Before this patch VF interface vanished when
maximum queue number was exceeded. Driver tried
to add next queues even if there was not enough
space. PF sent incorrect number of queues to
the VF when there were not enough of them.

Add an additional condition introduced to check
available space in 'qp_pile' before proceeding.
This condition makes it impossible to add queues
if they number is greater than the number resulting
from available space.
Also add the search for free space in PF queue
pair piles.

Without this patch VF interfaces are not seen
when available space for queues has been
exceeded and following logs appears permanently
in dmesg:
"Unable to get VF config (-32)".
"VF 62 failed opcode 3, retval: -5"
"Unable to get VF config due to PF error condition, not retrying"

Fixes: 7daa6bf3294e ("i40e: driver core headers")
Fixes: 41c445ff0f48 ("i40e: main driver core")
Signed-off-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Signed-off-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i40e: Increase delay to 1 s after global EMP reset

commit 9b13bd53134c9ddd544a790125199fdbdb505e67 upstream.

Recently simplified i40e_rebuild causes that FW sometimes
is not ready after NVM update, the ping does not return.

Increase the delay in case of EMP reset.
Old delay of 300 ms was introduced for specific cards for 710 series.
Now it works for all the cards and delay was increased.

Fixes: 1fa51a650e1d ("i40e: Add delay after EMP reset for firmware to recover")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/32: Fix boot failure with GCC latent entropy plugin

commit bba496656a73fc1d1330b49c7f82843836e9feb1 upstream.

Boot fails with GCC latent entropy plugin enabled.

This is due to early boot functions trying to access 'latent_entropy'
global data while the kernel is not relocated at its final
destination yet.

As there is no way to tell GCC to use PTRRELOC() to access it,
disable latent entropy plugin in early_32.o and feature-fixups.o and
code-patching.o

Fixes: 38addce8b600 ("gcc-plugins: Add latent_entropy plugin")
Cc: stable@vger.kernel.org # v4.9+
Reported-by: Erhard Furtner <erhard_f@mailbox.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215217
Link: https://lore.kernel.org/r/2bac55483b8daf5b1caa163a45fa5f9cdbe18be4.1640178426.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/32s: Fix kasan_init_region() for KASAN

commit d37823c3528e5e0705fc7746bcbc2afffb619259 upstream.

It has been reported some configuration where the kernel doesn't
boot with KASAN enabled.

This is due to wrong BAT allocation for the KASAN area:

---[ Data Block Address Translation ]---
0: 0xc0000000-0xcfffffff 0x00000000       256M Kernel rw      m
1: 0xd0000000-0xdfffffff 0x10000000       256M Kernel rw      m
2: 0xe0000000-0xefffffff 0x20000000       256M Kernel rw      m
3: 0xf8000000-0xf9ffffff 0x2a000000        32M Kernel rw      m
4: 0xfa000000-0xfdffffff 0x2c000000        64M Kernel rw      m

A BAT must have both virtual and physical addresses alignment matching
the size of the BAT. This is not the case for BAT 4 above.

Fix kasan_init_region() by using block_size() function that is in
book3s32/mmu.c. To be able to reuse it here, make it non static and
change its name to bat_block_size() in order to avoid name conflict
with block_size() defined in <linux/blkdev.h>

Also reuse find_free_bat() to avoid an error message from setbat()
when no BAT is available.

And allocate memory outside of linear memory mapping to avoid
wasting that precious space.

With this change we get correct alignment for BATs and KASAN shadow
memory is allocated outside the linear memory space.

---[ Data Block Address Translation ]---
0: 0xc0000000-0xcfffffff 0x00000000       256M Kernel rw
1: 0xd0000000-0xdfffffff 0x10000000       256M Kernel rw
2: 0xe0000000-0xefffffff 0x20000000       256M Kernel rw
3: 0xf8000000-0xfbffffff 0x7c000000        64M Kernel rw
4: 0xfc000000-0xfdffffff 0x7a000000        32M Kernel rw

Fixes: 7974c4732642 ("powerpc/32s: Implement dedicated kasan_init_region()")
Cc: stable@vger.kernel.org
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7a50ef902494d1325227d47d33dada01e52e5518.1641818726.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/32s: Allocate one 256k IBAT instead of two consecutives 128k IBATs

commit 37eb7ca91b692e8e49e7dd50158349a6c8fb5b09 upstream.

Today we have the following IBATs allocated:

---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000         4M Kernel   x     m
1: 0xc0400000-0xc05fffff 0x00400000         2M Kernel   x     m
2: 0xc0600000-0xc06fffff 0x00600000         1M Kernel   x     m
3: 0xc0700000-0xc077ffff 0x00700000       512K Kernel   x     m
4: 0xc0780000-0xc079ffff 0x00780000       128K Kernel   x     m
5: 0xc07a0000-0xc07bffff 0x007a0000       128K Kernel   x     m
6:         -
7:         -

The two 128K should be a single 256K instead.

When _etext is not aligned to 128Kbytes, the system will allocate
all necessary BATs to the lower 128Kbytes boundary, then allocate
an additional 128Kbytes BAT for the remaining block.

Instead, align the top to 128Kbytes so that the function directly
allocates a 256Kbytes last block:

---[ Instruction Block Address Translation ]---
0: 0xc0000000-0xc03fffff 0x00000000         4M Kernel   x     m
1: 0xc0400000-0xc05fffff 0x00400000         2M Kernel   x     m
2: 0xc0600000-0xc06fffff 0x00600000         1M Kernel   x     m
3: 0xc0700000-0xc077ffff 0x00700000       512K Kernel   x     m
4: 0xc0780000-0xc07bffff 0x00780000       256K Kernel   x     m
5:         -
6:         -
7:         -

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ab58b296832b0ec650e2203200e060adbcb2677d.1637930421.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/cpu: Add Xeon Icelake-D to list of CPUs that support PPIN

commit e464121f2d40eabc7d11823fb26db807ce945df4 upstream.

Missed adding the Icelake-D CPU to the list. It uses the same MSRs
to control and read the inventory number as all the other models.

Fixes: dc6b025de95b ("x86/mce: Add Xeon Icelake to list of CPUs that support PPIN")
Reported-by: Ailin Xu <ailin.xu@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220121174743.1875294-2-tony.luck@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/MCE/AMD: Allow thresholding interface updates after init

commit 1f52b0aba6fd37653416375cb8a1ca673acf8d5f upstream.

Changes to the AMD Thresholding sysfs code prevents sysfs writes from
updating the underlying registers once CPU init is completed, i.e.
"threshold_banks" is set.

Allow the registers to be updated if the thresholding interface is
already initialized or if in the init path. Use the "set_lvt_off" value
to indicate if running in the init path, since this value is only set
during init.

Fixes: a037f3ca0ea0 ("x86/mce/amd: Make threshold bank setting hotplug robust")
Signed-off-by: Yazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220117161328.19148-1-yazen.ghannam@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PCI/sysfs: Find shadow ROM before static attribute initialization

commit 66d28b21fe6b3da8d1e9f0a7ba38bc61b6c547e1 upstream.

Ville reported that the sysfs "rom" file for VGA devices disappeared after
527139d738d7 ("PCI/sysfs: Convert "rom" to static attribute").

Prior to 527139d738d7, FINAL fixups, including pci_fixup_video() where we
find shadow ROMs, were run before pci_create_sysfs_dev_files() created the
sysfs "rom" file.

After 527139d738d7, "rom" is a static attribute and is created before FINAL
fixups are run, so we didn't create "rom" files for shadow ROMs:

  acpi_pci_root_add
    ...
      pci_scan_single_device
        pci_device_add
          pci_fixup_video                    # <-- new HEADER fixup
          device_add
            ...
              if (grp->is_visible())
                pci_dev_rom_attr_is_visible  # after 527139d738d7
    pci_bus_add_devices
      pci_bus_add_device
        pci_fixup_device(pci_fixup_final)
          pci_fixup_video                    # <-- previous FINAL fixup
        pci_create_sysfs_dev_files
          if (pci_resource_len(pdev, PCI_ROM_RESOURCE))
            sysfs_create_bin_file("rom")     # before 527139d738d7

Change pci_fixup_video() to be a HEADER fixup so it runs before sysfs
static attributes are initialized.

Rename the Loongson pci_fixup_radeon() to pci_fixup_video() and make its
dmesg logging identical to the others since it is doing the same job.

Link: https://lore.kernel.org/r/YbxqIyrkv3GhZVxx@intel.com
Fixes: 527139d738d7 ("PCI/sysfs: Convert "rom" to static attribute")
Link: https://lore.kernel.org/r/20220126154001.16895-1-helgaas@kernel.org
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v5.13+
Cc: Huacai Chen <chenhuacai@kernel.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sched/membarrier: Fix membarrier-rseq fence command missing from query bitmask

commit 809232619f5b15e31fb3563985e705454f32621f upstream.

The membarrier command MEMBARRIER_CMD_QUERY allows querying the
available membarrier commands. When the membarrier-rseq fence commands
were added, a new MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK was
introduced with the intent to expose them with the MEMBARRIER_CMD_QUERY
command, the but it was never added to MEMBARRIER_CMD_BITMASK.

The membarrier-rseq fence commands are therefore not wired up with the
query command.

Rename MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK to
MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK (the bitmask is not a command
per-se), and change the erroneous
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ_BITMASK (which does not
actually exist) to MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ.

Wire up MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK in
MEMBARRIER_CMD_BITMASK. Fixing this allows discovering availability of
the membarrier-rseq fence feature.

Fixes: 2a36ab717e8f ("rseq/membarrier: Add MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 5.10+
Link: https://lkml.kernel.org/r/20220117203010.30129-1-mathieu.desnoyers@efficios.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ocfs2: fix a deadlock when commit trans

commit ddf4b773aa40790dfa936bd845c18e735a49c61c upstream.

commit 6f1b228529ae introduces a regression which can deadlock as
follows:

  Task1:                              Task2:
  jbd2_journal_commit_transaction     ocfs2_test_bg_bit_allocatable
  spin_lock(&jh->b_state_lock)        jbd_lock_bh_journal_head
  __jbd2_journal_remove_checkpoint    spin_lock(&jh->b_state_lock)
  jbd2_journal_put_journal_head
  jbd_lock_bh_journal_head

Task1 and Task2 lock bh->b_state and jh->b_state_lock in different
order, which finally result in a deadlock.

So use jbd2_journal_[grab|put]_journal_head instead in
ocfs2_test_bg_bit_allocatable() to fix it.

Link: https://lkml.kernel.org/r/20220121071205.100648-3-joseph.qi@linux.alibaba.com
Fixes: 6f1b228529ae ("ocfs2: fix race between searching chunks and release journal_head from buffer_head")
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Reported-by: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Tested-by: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Reported-by: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

jbd2: export jbd2_journal_[grab|put]_journal_head

commit 4cd1103d8c66b2cdb7e64385c274edb0ac5e8887 upstream.

Patch series "ocfs2: fix a deadlock case".

This fixes a deadlock case in ocfs2.  We firstly export jbd2 symbols
jbd2_journal_[grab|put]_journal_head as preparation and later use them
in ocfs2 insread of jbd_[lock|unlock]_bh_journal_head to fix the
deadlock.

This patch (of 2):

This exports symbols jbd2_journal_[grab|put]_journal_head, which will be
used outside modules, e.g.  ocfs2.

Link: https://lkml.kernel.org/r/20220121071205.100648-2-joseph.qi@linux.alibaba.com
Signed-off-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Gautham Ananthakrishna <gautham.ananthakrishna@oracle.com>
Cc: Saeed Mirzamohammadi <saeed.mirzamohammadi@oracle.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm, kasan: use compare-exchange operation to set KASAN page tag

commit 27fe73394a1c6d0b07fa4d95f1bca116d1cc66e9 upstream.

It has been reported that the tag setting operation on newly-allocated
pages can cause the page flags to be corrupted when performed
concurrently with other flag updates as a result of the use of
non-atomic operations.

Fix the problem by using a compare-exchange loop to update the tag.

Link: https://lkml.kernel.org/r/20220120020148.1632253-1-pcc@google.com
Link: https://linux-review.googlesource.com/id/I456b24a2b9067d93968d43b4bb3351c0cec63101
Fixes: 2813b9c02962 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Signed-off-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ucsi_ccg: Check DEV_INT bit only when starting CCG4

commit 825911492eb15bf8bb7fb94bc0c0421fe7a6327d upstream.

CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.

The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.

Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: tcpm: Do not disconnect when receiving VSAFE0V

commit 746f96e7d6f7a276726860f696671766bfb24cf0 upstream.

With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V causing VSAFE0V to be triggered. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED state where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid VSAFE0V events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.

Stub from the spec:
    "4.5.2.2.4.2 Exiting from AttachWait.SNK State
    A Sink shall transition to Unattached.SNK when the state of both
    the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
    A DRP shall transition to Unattached.SRC when the state of both
    the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."

[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling

Fixes: 28b43d3d746b8 ("usb: typec: tcpm: Introduce vsafe0v for vbus")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: tcpm: Do not disconnect while receiving VBUS off

commit 90b8aa9f5b09edae6928c0561f933fec9f7a9987 upstream.

With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.

Stub from the spec:
    "4.5.2.2.4.2 Exiting from AttachWait.SNK State
    A Sink shall transition to Unattached.SNK when the state of both
    the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
    A DRP shall transition to Unattached.SRC when the state of both
    the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."

[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling

Fixes: f0690a25a140b8 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: tcpci: don't touch CC line if it's Vconn source

commit 5638b0dfb6921f69943c705383ff40fb64b987f2 upstream.

With the AMS and Collision Avoidance, tcpm often needs to change the CC's
termination. When one CC line is sourcing Vconn, if we still change its
termination, the voltage of the another CC line is likely to be fluctuant
and unstable.

Therefore, we should verify whether a CC line is sourcing Vconn before
changing its termination and only change the termination that is not
a Vconn line. This can be done by reading the Vconn Present bit of
POWER_ STATUS register. To determine the polarity, we can read the
Plug Orientation bit of TCPC_CONTROL register. Since Vconn can only be
sourced if Plug Orientation is set.

Fixes: 0908c5aca31e ("usb: typec: tcpm: AMS and Collision Avoidance")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20220113092943.752372-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: core: Fix hang in usb_kill_urb by adding memory barriers

commit 26fbe9772b8c459687930511444ce443011f86bf upstream.

The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return.  It turns out the issue is not unlinking
the URB; that works just fine.  Rather, the problem arises when the
wakeup notification that the URB has completed is not received.

The reason is memory-access ordering on SMP systems.  In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:

CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
  ...   ...
  atomic_inc(&urb->reject);   atomic_dec(&urb->use_count);
  ...   ...
  wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
  if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);

Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:

write urb->reject, then read urb->use_count;

whereas the overall pattern of accesses on CPU 1 is:

write urb->use_count, then read urb->reject.

This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes.  The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject.  Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().

The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().

The problem is fixed by adding suitable memory barriers.  To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs.  The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.

This patch adds the necessary memory barriers.

CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: xilinx: Fix error handling when getting USB3 PHY

commit 2cc9b1c93b1c4caa2d971856c0780fb5f7d04692 upstream.

The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.

Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: dwc3: xilinx: Skip resets and USB3 register settings for USB2.0 mode

commit 9678f3361afc27a3124cd2824aec0227739986fb upstream.

It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.

Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.

Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: cdnsp: Fix segmentation fault in cdns_lost_power function

commit 79aa3e19fe8f5be30e846df8a436bfe306e8b1a6 upstream.

CDNSP driver read not initialized cdns->otg_v0_regs
which lead to segmentation fault. Patch fixes this issue.

Fixes: 2cf2581cd229 ("usb: cdns3: add power lost support for system resume")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220111090737.10345-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: f_sourcesink: Fix isoc transfer for USB_SPEED_SUPER_PLUS

commit 904edf8aeb459697129be5fde847e2a502f41fd9 upstream.

Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.

Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: common: ulpi: Fix crash in ulpi_match()

commit 2e3dd4a6246945bf84ea6f478365d116e661554c upstream.

Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.

The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.

Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci-plat: fix crash when suspend if remote wake enable

commit 9df478463d9feb90dae24f183383961cf123a0ec upstream.

Crashed at i.mx8qm platform when suspend if enable remote wakeup

Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 244 Comm: kworker/u12:6 Not tainted 5.15.5-dirty #12
Hardware name: Freescale i.MX8QM MEK (DT)
Workqueue: events_unbound async_run_entry_fn
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : xhci_disable_hub_port_wake.isra.62+0x60/0xf8
lr : xhci_disable_hub_port_wake.isra.62+0x34/0xf8
sp : ffff80001394bbf0
x29: ffff80001394bbf0 x28: 0000000000000000 x27: ffff00081193b578
x26: ffff00081193b570 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00081193a29c x22: 0000000000020001 x21: 0000000000000001
x20: 0000000000000000 x19: ffff800014e90490 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000002 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000960 x9 : ffff80001394baa0
x8 : ffff0008145d1780 x7 : ffff0008f95b8e80 x6 : 000000001853b453
x5 : 0000000000000496 x4 : 0000000000000000 x3 : ffff00081193a29c
x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff000814591620
Call trace:
 xhci_disable_hub_port_wake.isra.62+0x60/0xf8
 xhci_suspend+0x58/0x510
 xhci_plat_suspend+0x50/0x78
 platform_pm_suspend+0x2c/0x78
 dpm_run_callback.isra.25+0x50/0xe8
 __device_suspend+0x108/0x3c0

The basic flow:
1. run time suspend call xhci_suspend, xhci parent devices gate the clock.
        2. echo mem >/sys/power/state, system _device_suspend call xhci_suspend
        3. xhci_suspend call xhci_disable_hub_port_wake, which access register,
   but clock already gated by run time suspend.

This problem was hidden by power domain driver, which call run time resume before it.

But the below commit remove it and make this issue happen.
commit c1df456d0f06e ("PM: domains: Don't runtime resume devices at genpd_prepare()")

This patch call run time resume before suspend to make sure clock is on
before access register.

Reviewed-by: Peter Chen <peter.chen@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Testeb-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220110172738.31686-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-storage: Add unusual-devs entry for VL817 USB-SATA bridge

commit 5b67b315037250a61861119683e7fcb509deea25 upstream.

Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver.  Typical log messages are:

[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success

Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.

In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default.  Users will be able to override this entry by means
of a module parameter, if they want.

CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kbuild: remove include/linux/cyclades.h from header file check

commit d1ad2721b1eb05d54e81393a7ebc332d4a35c68f upstream.

The file now rightfully throws up a big warning that it should never be
included, so remove it from the header_check test.

Fixes: f23653fe6447 ("tty: Partially revert the removal of the Cyclades public API")
Cc: stable <stable@vger.kernel.org>
Cc: Masahiro Yamada <masahiroy@kernel.org>
Cc: "Maciej W. Rozycki" <macro@embecosm.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20220127073304.42399-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Add support for Brainboxes UC cards.

commit 152d1afa834c84530828ee031cf07a00e0fc0b8c upstream.

This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.

Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: Partially revert the removal of the Cyclades public API

commit f23653fe64479d96910bfda2b700b1af17c991ac upstream.

Fix a user API regression introduced with commit f76edd8f7ce0 ("tty:
cyclades, remove this orphan"), which removed a part of the API and
caused compilation errors for user programs using said part, such as
GCC 9 in its libsanitizer component[1]:

.../libsanitizer/sanitizer_common/sanitizer_platform_limits_posix.cc:160:10: fatal error: linux/cyclades.h: No such file or directory
  160 | #include <linux/cyclades.h>
      |          ^~~~~~~~~~~~~~~~~~
compilation terminated.
make[4]: *** [Makefile:664: sanitizer_platform_limits_posix.lo] Error 1

As the absolute minimum required bring `struct cyclades_monitor' and
ioctl numbers back then so as to make the library build again.  Add a
preprocessor warning as to the obsolescence of the features provided.

References:

[1] GCC PR sanitizer/100379, "cyclades.h is removed from linux kernel
    header files", <https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100379>

Fixes: f76edd8f7ce0 ("tty: cyclades, remove this orphan")
Cc: stable@vger.kernel.org # v5.13+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maciej W. Rozycki <macro@embecosm.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.20.2201260733430.11348@tpp.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: n_gsm: fix SW flow control encoding/handling

commit 8838b2af23caf1ff0610caef2795d6668a013b2d upstream.

n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.

ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en

To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.

This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.

Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: stm32: fix software flow control transfer

commit 037b91ec7729524107982e36ec4b40f9b174f7a2 upstream.

x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty.

Fix start_tx condition to allow x_char to be sent.

Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: 8250: of: Fix mapped region size when using reg-offset property

commit d06b1cf28297e27127d3da54753a3a01a2fa2f28 upstream.

8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.

Fix this by subtracting reg-offset from the mapped region size.

Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

serial: pl011: Fix incorrect rs485 RTS polarity on set_mctrl

commit 62f676ff7898f6c1bd26ce014564773a3dc00601 upstream.

Commit 8d479237727c ("serial: amba-pl011: add RS485 support") sought to
keep RTS deasserted on set_mctrl if rs485 is enabled.  However it did so
only if deasserted RTS polarity is high.  Fix it in case it's low.

Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org # v5.15+
Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Jochen Mades <jochen@mades.net>
[lukas: copyedit commit message, add stable designation]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/85fa3323ba8c307943969b7343e23f34c3e652ba.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm: properly fix redundant bio-based IO accounting

commit b879f915bc48a18d4f4462729192435bb0f17052 upstream.

Record the start_time for a bio but defer the starting block core's IO
accounting until after IO is submitted using bio_start_io_acct_time().

This approach avoids the need to mess around with any of the
individual IO stats in response to a bio_split() that follows bio
submission.

Reported-by: Bud Brown <bubrown@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Depends-on: e45c47d1f94e ("block: add bio_start_io_acct_time() to control start_time")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Link: https://lore.kernel.org/r/20220128155841.39644-4-snitzer@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

block: add bio_start_io_acct_time() to control start_time

commit e45c47d1f94e0cc7b6b079fdb4bcce2995e2adc4 upstream.

bio_start_io_acct_time() interface is like bio_start_io_acct() that
allows start_time to be passed in. This gives drivers the ability to
defer starting accounting until after IO is issued (but possibily not
entirely due to bio splitting).

Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Link: https://lore.kernel.org/r/20220128155841.39644-2-snitzer@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dm: revert partial fix for redundant bio-based IO accounting

commit f524d9c95fab54783d0038f7a3e8c014d5b56857 upstream.

Reverts a1e1cb72d9649 ("dm: fix redundant IO accounting for bios that
need splitting") because it was too narrow in scope (only addressed
redundant 'sectors[]' accounting and not ios, nsecs[], etc).

Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Link: https://lore.kernel.org/r/20220128155841.39644-3-snitzer@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S HV Nested: Fix nested HFSCR being clobbered with multiple vCPUs

commit 22f7ff0dea9491e90b6fe808ed40c30bd791e5c2 upstream.

The L0 is storing HFSCR requested by the L1 for the L2 in struct
kvm_nested_guest when the L1 requests a vCPU enter L2. kvm_nested_guest
is not a per-vCPU structure. Hilarity ensues.

Fix it by moving the nested hfscr into the vCPU structure together with
the other per-vCPU nested fields.

Fixes: 8b210a880b35 ("KVM: PPC: Book3S HV Nested: Make nested HFSCR state accessible")
Cc: stable@vger.kernel.org # v5.15+
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Fabiano Rosas <farosas@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20220122105530.3477250-1-npiggin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Sync the states size with the XCR0/IA32_XSS at, any time

commit 05a9e065059e566f218f8778c4d17ee75db56c55 upstream.

XCR0 is reset to 1 by RESET but not INIT and IA32_XSS is zeroed by
both RESET and INIT. The kvm_set_msr_common()'s handling of MSR_IA32_XSS
also needs to update kvm_update_cpuid_runtime(). In the above cases, the
size in bytes of the XSAVE area containing all states enabled by XCR0 or
(XCRO | IA32_XSS) needs to be updated.

For simplicity and consistency, existing helpers are used to write values
and call kvm_update_cpuid_runtime(), and it's not exactly a fast path.

Fixes: a554d207dc46 ("KVM: X86: Processor States following Reset or INIT")
Cc: stable@vger.kernel.org
Signed-off-by: Like Xu <likexu@tencent.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220126172226.2298529-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Update vCPU's runtime CPUID on write to MSR_IA32_XSS

commit 4c282e51e4450b94680d6ca3b10f830483b1f243 upstream.

Do a runtime CPUID update for a vCPU if MSR_IA32_XSS is written, as the
size in bytes of the XSAVE area is affected by the states enabled in XSS.

Fixes: 203000993de5 ("kvm: vmx: add MSR logic for XSAVES")
Cc: stable@vger.kernel.org
Signed-off-by: Like Xu <likexu@tencent.com>
[sean: split out as a separate patch, adjust Fixes tag]
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220126172226.2298529-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Keep MSR_IA32_XSS unchanged for INIT

commit be4f3b3f82271c3193ce200a996dc70682c8e622 upstream.

It has been corrected from SDM version 075 that MSR_IA32_XSS is reset to
zero on Power up and Reset but keeps unchanged on INIT.

Fixes: a554d207dc46 ("KVM: X86: Processor States following Reset or INIT")
Cc: stable@vger.kernel.org
Signed-off-by: Xiaoyao Li <xiaoyao.li@intel.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220126172226.2298529-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Forcibly leave nested virt when SMM state is toggled

commit f7e570780efc5cec9b2ed1e0472a7da14e864fdb upstream.

Forcibly leave nested virtualization operation if userspace toggles SMM
state via KVM_SET_VCPU_EVENTS or KVM_SYNC_X86_EVENTS.  If userspace
forces the vCPU out of SMM while it's post-VMXON and then injects an SMI,
vmx_enter_smm() will overwrite vmx->nested.smm.vmxon and end up with both
vmxon=false and smm.vmxon=false, but all other nVMX state allocated.

Don't attempt to gracefully handle the transition as (a) most transitions
are nonsencial, e.g. forcing SMM while L2 is running, (b) there isn't
sufficient information to handle all transitions, e.g. SVM wants access
to the SMRAM save state, and (c) KVM_SET_VCPU_EVENTS must precede
KVM_SET_NESTED_STATE during state restore as the latter disallows putting
the vCPU into L2 if SMM is active, and disallows tagging the vCPU as
being post-VMXON in SMM if SMM is not active.

Abuse of KVM_SET_VCPU_EVENTS manifests as a WARN and memory leak in nVMX
due to failure to free vmcs01's shadow VMCS, but the bug goes far beyond
just a memory leak, e.g. toggling SMM on while L2 is active puts the vCPU
in an architecturally impossible state.

  WARNING: CPU: 0 PID: 3606 at free_loaded_vmcs arch/x86/kvm/vmx/vmx.c:2665 [inline]
  WARNING: CPU: 0 PID: 3606 at free_loaded_vmcs+0x158/0x1a0 arch/x86/kvm/vmx/vmx.c:2656
  Modules linked in:
  CPU: 1 PID: 3606 Comm: syz-executor725 Not tainted 5.17.0-rc1-syzkaller #0
  Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
  RIP: 0010:free_loaded_vmcs arch/x86/kvm/vmx/vmx.c:2665 [inline]
  RIP: 0010:free_loaded_vmcs+0x158/0x1a0 arch/x86/kvm/vmx/vmx.c:2656
  Code: <0f> 0b eb b3 e8 8f 4d 9f 00 e9 f7 fe ff ff 48 89 df e8 92 4d 9f 00
  Call Trace:
   <TASK>
   kvm_arch_vcpu_destroy+0x72/0x2f0 arch/x86/kvm/x86.c:11123
   kvm_vcpu_destroy arch/x86/kvm/../../../virt/kvm/kvm_main.c:441 [inline]
   kvm_destroy_vcpus+0x11f/0x290 arch/x86/kvm/../../../virt/kvm/kvm_main.c:460
   kvm_free_vcpus arch/x86/kvm/x86.c:11564 [inline]
   kvm_arch_destroy_vm+0x2e8/0x470 arch/x86/kvm/x86.c:11676
   kvm_destroy_vm arch/x86/kvm/../../../virt/kvm/kvm_main.c:1217 [inline]
   kvm_put_kvm+0x4fa/0xb00 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1250
   kvm_vm_release+0x3f/0x50 arch/x86/kvm/../../../virt/kvm/kvm_main.c:1273
   __fput+0x286/0x9f0 fs/file_table.c:311
   task_work_run+0xdd/0x1a0 kernel/task_work.c:164
   exit_task_work include/linux/task_work.h:32 [inline]
   do_exit+0xb29/0x2a30 kernel/exit.c:806
   do_group_exit+0xd2/0x2f0 kernel/exit.c:935
   get_signal+0x4b0/0x28c0 kernel/signal.c:2862
   arch_do_signal_or_restart+0x2a9/0x1c40 arch/x86/kernel/signal.c:868
   handle_signal_work kernel/entry/common.c:148 [inline]
   exit_to_user_mode_loop kernel/entry/common.c:172 [inline]
   exit_to_user_mode_prepare+0x17d/0x290 kernel/entry/common.c:207
   __syscall_exit_to_user_mode_work kernel/entry/common.c:289 [inline]
   syscall_exit_to_user_mode+0x19/0x60 kernel/entry/common.c:300
   do_syscall_64+0x42/0xb0 arch/x86/entry/common.c:86
   entry_SYSCALL_64_after_hwframe+0x44/0xae
   </TASK>

Cc: stable@vger.kernel.org
Reported-by: syzbot+8112db3ab20e70d50c31@syzkaller.appspotmail.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20220125220358.2091737-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: nSVM: skip eax alignment check for non-SVM instructions

commit 47c28d436f409f5b009dc82bd82d4971088aa391 upstream.

The bug occurs on #GP triggered by VMware backdoor when eax value is
unaligned. eax alignment check should not be applied to non-SVM
instructions because it leads to incorrect omission of the instructions
emulation.
Apply the alignment check only to SVM instructions to fix.

Fixes: d1cba6c92237 ("KVM: x86: nSVM: test eax for 4K alignment for GP errata workaround")
Signed-off-by: Denis Valeev <lemniscattaden@gmail.com>
Message-Id: <Yexlhaoe1Fscm59u@q>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: SVM: Don't intercept #GP for SEV guests

commit 0b0be065b7563ac708aaa9f69dd4941c80b3446d upstream.

Never intercept #GP for SEV guests as reading SEV guest private memory
will return cyphertext, i.e. emulating on #GP can't work as intended.

Cc: stable@vger.kernel.org
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: SVM: Never reject emulation due to SMAP errata for !SEV guests

commit 55467fcd55b89c622e62b4afe60ac0eb2fae91f2 upstream.

Always signal that emulation is possible for !SEV guests regardless of
whether or not the CPU provided a valid instruction byte stream.  KVM can
read all guest state (memory and registers) for !SEV guests, i.e. can
fetch the code stream from memory even if the CPU failed to do so because
of the SMAP errata.

Fixes: 05d5a4863525 ("KVM: SVM: Workaround errata#1096 (insn_len maybe zero on SMAP violation)")
Cc: stable@vger.kernel.org
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: LAPIC: Also cancel preemption timer during SET_LAPIC

commit 35fe7cfbab2e81f1afb23fc4212210b1de6d9633 upstream.

The below warning is splatting during guest reboot.

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 1931 at arch/x86/kvm/x86.c:10322 kvm_arch_vcpu_ioctl_run+0x874/0x880 [kvm]
  CPU: 0 PID: 1931 Comm: qemu-system-x86 Tainted: G          I       5.17.0-rc1+ #5
  RIP: 0010:kvm_arch_vcpu_ioctl_run+0x874/0x880 [kvm]
  Call Trace:
   <TASK>
   kvm_vcpu_ioctl+0x279/0x710 [kvm]
   __x64_sys_ioctl+0x83/0xb0
   do_syscall_64+0x3b/0xc0
   entry_SYSCALL_64_after_hwframe+0x44/0xae
  RIP: 0033:0x7fd39797350b

This can be triggered by not exposing tsc-deadline mode and doing a reboot in
the guest. The lapic_shutdown() function which is called in sys_reboot path
will not disarm the flying timer, it just masks LVTT. lapic_shutdown() clears
APIC state w/ LVT_MASKED and timer-mode bit is 0, this can trigger timer-mode
switch between tsc-deadline and oneshot/periodic, which can result in preemption
timer be cancelled in apic_update_lvtt(). However, We can't depend on this when
not exposing tsc-deadline mode and oneshot/periodic modes emulated by preemption
timer. Qemu will synchronise states around reset, let's cancel preemption timer
under KVM_SET_LAPIC.

Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1643102220-35667-1-git-send-email-wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amd/display: Fix FP start/end for dcn30_internal_validate_bw.

commit 72a8d87b87270bff0c0b2fed4d59c48d0dd840d7 upstream.

It calls populate_dml_pipes which uses doubles to initialize the
scale_ratio_depth params. Mirrors the dcn20 logic.

Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/atomic: Add the crtc to affected crtc only if uapi.enable = true

commit 5ec1cebd59300ddd26dbaa96c17c508764eef911 upstream.

In case of a modeset where a mode gets split across multiple CRTCs
in the driver specific implementation (bigjoiner in i915) we wrongly count
the affected CRTCs based on the drm_crtc_mask and indicate the stolen CRTC as
an affected CRTC in atomic_check_only().
This triggers a warning since affected CRTCs doent match requested CRTC.

To fix this in such bigjoiner configurations, we should only
increment affected crtcs if that CRTC is enabled in UAPI not
if it is just used internally in the driver to split the mode.

v3: Add the same uapi crtc_state->enable check in requested
crtc calc (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Simon Ser <contact@emersion.fr>
Cc: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.11+
Fixes: 919c2299a893 ("drm/i915: Enable bigjoiner")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004115913.23889-1-manasi.d.navare@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/etnaviv: relax submit size limits

commit e3d26528e083e612314d4dcd713f3d5a26143ddc upstream.

While all userspace tried to limit commandstreams to 64K in size,
a bug in the Mesa driver lead to command streams of up to 128K
being submitted. Allow those to avoid breaking existing userspace.

Fixes: 6dfa2fab8ddd ("drm/etnaviv: limit submit sizes")
Cc: stable@vger.kernel.org
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel: Add a quirk for the calculation of the number of counters on Alder Lake

commit 7fa981cad216e9f64f49e22112f610c0bfed91bc upstream.

For some Alder Lake machine with all E-cores disabled in a BIOS, the
below warning may be triggered.

[ 2.010766] hw perf events fixed 5 > max(4), clipping!

Current perf code relies on the CPUID leaf 0xA and leaf 7.EDX[15] to
calculate the number of the counters and follow the below assumption.

For a hybrid configuration, the leaf 7.EDX[15] (X86_FEATURE_HYBRID_CPU)
is set. The leaf 0xA only enumerate the common counters. Linux perf has
to manually add the extra GP counters and fixed counters for P-cores.
For a non-hybrid configuration, the X86_FEATURE_HYBRID_CPU should not
be set. The leaf 0xA enumerates all counters.

However, that's not the case when all E-cores are disabled in a BIOS.
Although there are only P-cores in the system, the leaf 7.EDX[15]
(X86_FEATURE_HYBRID_CPU) is still set. But the leaf 0xA is updated
to enumerate all counters of P-cores. The inconsistency triggers the
warning.

Several software ways were considered to handle the inconsistency.
- Drop the leaf 0xA and leaf 7.EDX[15] CPUID enumeration support.
  Hardcode the number of counters. This solution may be a problem for
  virtualization. A hypervisor cannot control the number of counters
  in a Linux guest via changing the guest CPUID enumeration anymore.
- Find another CPUID bit that is also updated with E-cores disabled.
  There may be a problem in the virtualization environment too. Because
  a hypervisor may disable the feature/CPUID bit.
- The P-cores have a maximum of 8 GP counters and 4 fixed counters on
  ADL. The maximum number can be used to detect the case.
  This solution is implemented in this patch.

Fixes: ee72a94ea4a6 ("perf/x86/intel: Fix fixed counter check warning for some Alder Lake")
Reported-by: Damjan Marion (damarion) <damarion@cisco.com>
Reported-by: Chan Edison <edison_chan_gz@hotmail.com>
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: Damjan Marion (damarion) <damarion@cisco.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1641925238-149288-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

perf/x86/intel/uncore: Fix CAS_COUNT_WRITE issue for ICX

commit 96fd2e89fba1aaada6f4b1e5d25a9d9ecbe1943d upstream.

The user recently report a perf issue in the ICX platform, when test by
perf event “uncore_imc_x/cas_count_write”,the write bandwidth is always
very small (only 0.38MB/s), it is caused by the wrong "umask" for the
"cas_count_write" event. When double-checking, find "cas_count_read"
also is wrong.

The public document for ICX uncore:

3rd Gen Intel® Xeon® Processor Scalable Family, Codename Ice Lake,Uncore
Performance Monitoring Reference Manual, Revision 1.00, May 2021

On 2.4.7, it defines Unit Masks for CAS_COUNT:
RD b00001111
WR b00110000

So corrected both "cas_count_read" and "cas_count_write" for ICX.

Old settings:
 hswep_uncore_imc_events
INTEL_UNCORE_EVENT_DESC(cas_count_read,  "event=0x04,umask=0x03")
INTEL_UNCORE_EVENT_DESC(cas_count_write, "event=0x04,umask=0x0c")

New settings:
 snr_uncore_imc_events
INTEL_UNCORE_EVENT_DESC(cas_count_read,  "event=0x04,umask=0x0f")
INTEL_UNCORE_EVENT_DESC(cas_count_write, "event=0x04,umask=0x30")

Fixes: 2b3b76b5ec67 ("perf/x86/intel/uncore: Add Ice Lake server uncore support")
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Kan Liang <kan.liang@linux.intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20211223144826.841267-1-zhengjun.xing@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/audit: Fix syscall_get_arch()

commit 252745240ba0ae774d2f80c5e185ed59fbc4fb41 upstream.

Commit 770cec16cdc9 ("powerpc/audit: Simplify syscall_get_arch()")
and commit 898a1ef06ad4 ("powerpc/audit: Avoid unneccessary #ifdef
in syscall_get_arguments()")
replaced test_tsk_thread_flag(task, TIF_32BIT)) by is_32bit_task().

But is_32bit_task() applies on current task while be want the test
done on task 'task'

So add a new macro is_tsk_32bit_task() to check any task.

Fixes: 770cec16cdc9 ("powerpc/audit: Simplify syscall_get_arch()")
Fixes: 898a1ef06ad4 ("powerpc/audit: Avoid unneccessary #ifdef in syscall_get_arguments()")
Cc: stable@vger.kernel.org
Reported-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/c55cddb8f65713bf5859ed675d75a50cb37d5995.1642159570.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

psi: Fix uaf issue when psi trigger is destroyed while being polled

commit a06247c6804f1a7c86a2e5398a4c1f1db1471848 upstream.

With write operation on psi files replacing old trigger with a new one,
the lifetime of its waitqueue is totally arbitrary. Overwriting an
existing trigger causes its waitqueue to be freed and pending poll()
will stumble on trigger->event_wait which was destroyed.
Fix this by disallowing to redefine an existing psi trigger. If a write
operation is used on a file descriptor with an already existing psi
trigger, the operation will fail with EBUSY error.
Also bypass a check for psi_disabled in the psi_trigger_destroy as the
flag can be flipped after the trigger is created, leading to a memory
leak.

Fixes: 0e94682b73bf ("psi: introduce psi monitor")
Reported-by: syzbot+cdb5dd11c97cc532efad@syzkaller.appspotmail.com
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Analyzed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Eric Biggers <ebiggers@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20220111232309.1786347-1-surenb@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "KVM: SVM: avoid infinite loop on NPF from bad address"

commit 31c25585695abdf03d6160aa6d829e855b256329 upstream.

Revert a completely broken check on an "invalid" RIP in SVM's workaround
for the DecodeAssists SMAP errata.  kvm_vcpu_gfn_to_memslot() obviously
expects a gfn, i.e. operates in the guest physical address space, whereas
RIP is a virtual (not even linear) address.  The "fix" worked for the
problematic KVM selftest because the test identity mapped RIP.

Fully revert the hack instead of trying to translate RIP to a GPA, as the
non-SEV case is now handled earlier, and KVM cannot access guest page
tables to translate RIP.

This reverts commit e72436bc3a5206f95bb384e741154166ddb3202e.

Fixes: e72436bc3a52 ("KVM: SVM: avoid infinite loop on NPF from bad address")
Reported-by: Liam Merwick <liam.merwick@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Liam Merwick <liam.merwick@oracle.com>
Message-Id: <20220120010719.711476-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fsnotify: fix fsnotify hooks in pseudo filesystems

commit 29044dae2e746949ad4b9cbdbfb248994d1dcdb4 upstream.

Commit 49246466a989 ("fsnotify: move fsnotify_nameremove() hook out of
d_delete()") moved the fsnotify delete hook before d_delete() so fsnotify
will have access to a positive dentry.

This allowed a race where opening the deleted file via cached dentry
is now possible after receiving the IN_DELETE event.

To fix the regression in pseudo filesystems, convert d_delete() calls
to d_drop() (see commit 46c46f8df9aa ("devpts_pty_kill(): don't bother
with d_delete()") and move the fsnotify hook after d_drop().

Add a missing fsnotify_unlink() hook in nfsdfs that was found during
the audit of fsnotify hooks in pseudo filesystems.

Note that the fsnotify hooks in simple_recursive_removal() follow
d_invalidate(), so they require no change.

Link: https://lore.kernel.org/r/20220120215305.282577-2-amir73il@gmail.com
Reported-by: Ivan Delalande <colona@arista.com>
Link: https://lore.kernel.org/linux-fsdevel/YeNyzoDM5hP5LtGW@visor/
Fixes: 49246466a989 ("fsnotify: move fsnotify_nameremove() hook out of d_delete()")
Cc: stable@vger.kernel.org # v5.3+
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: set pool_ns in new inode layout for async creates

commit 4584a768f22b7669cdebabc911543621ac661341 upstream.

Dan reported that he was unable to write to files that had been
asynchronously created when the client's OSD caps are restricted to a
particular namespace.

The issue is that the layout for the new inode is only partially being
filled. Ensure that we populate the pool_ns_data and pool_ns_len in the
iinfo before calling ceph_fill_inode.

Cc: stable@vger.kernel.org
URL: https://tracker.ceph.com/issues/54013
Fixes: 9a8d03ca2e2c ("ceph: attempt to do async create when possible")
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: properly put ceph_string reference after async create attempt

commit 932a9b5870d38b87ba0a9923c804b1af7d3605b9 upstream.

The reference acquired by try_prep_async_create is currently leaked.
Ensure we put it.

Cc: stable@vger.kernel.org
Fixes: 9a8d03ca2e2c ("ceph: attempt to do async create when possible")
Signed-off-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Don't inc err_log entry count if entry allocation fails

commit 67ab5eb71b37b55f7c5522d080a1b42823351776 upstream.

tr->n_err_log_entries should only be increased if entry allocation
succeeds.

Doing it when it fails won't cause any problems other than wasting an
entry, but should be fixed anyway.

Link: https://lkml.kernel.org/r/cad1ab28f75968db0f466925e7cba5970cec6c29.1643319703.git.zanussi@kernel.org
Cc: stable@vger.kernel.org
Fixes: 2f754e771b1a6 ("tracing: Don't inc err_log entry count if entry allocation fails")
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing/histogram: Fix a potential memory leak for kstrdup()

commit e629e7b525a179e29d53463d992bdee759c950fb upstream.

kfree() is missing on an error path to free the memory allocated by
kstrdup():

  p = param = kstrdup(data->params[i], GFP_KERNEL);

So it is better to free it via kfree(p).

Link: https://lkml.kernel.org/r/tencent_C52895FD37802832A3E5B272D05008866F0A@qq.com
Cc: stable@vger.kernel.org
Fixes: d380dcde9a07c ("tracing: Fix now invalid var_ref_vals assumption in trace action")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PM: wakeup: simplify the output logic of pm_show_wakelocks()

commit c9d967b2ce40d71e968eb839f36c936b8a9cf1ea upstream.

The buffer handling in pm_show_wakelocks() is tricky, and hopefully
correct.  Ensure it really is correct by using sysfs_emit_at() which
handles all of the tricky string handling logic in a PAGE_SIZE buffer
for us automatically as this is a sysfs file being read from.

Reviewed-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efi: runtime: avoid EFIv2 runtime services on Apple x86 machines

commit f5390cd0b43c2e54c7cf5506c7da4a37c5cef746 upstream.

Aditya reports [0] that his recent MacbookPro crashes in the firmware
when using the variable services at runtime. The culprit appears to be a
call to QueryVariableInfo(), which we did not use to call on Apple x86
machines in the past as they only upgraded from EFI v1.10 to EFI v2.40
firmware fairly recently, and QueryVariableInfo() (along with
UpdateCapsule() et al) was added in EFI v2.00.

The only runtime service introduced in EFI v2.00 that we actually use in
Linux is QueryVariableInfo(), as the capsule based ones are optional,
generally not used at runtime (all the LVFS/fwupd firmware update
infrastructure uses helper EFI programs that invoke capsule update at
boot time, not runtime), and not implemented by Apple machines in the
first place. QueryVariableInfo() is used to 'safely' set variables,
i.e., only when there is enough space. This prevents machines with buggy
firmwares from corrupting their NVRAMs when they run out of space.

Given that Apple machines have been using EFI v1.10 services only for
the longest time (the EFI v2.0 spec was released in 2006, and Linux
support for the newly introduced runtime services was added in 2011, but
the MacbookPro12,1 released in 2015 still claims to be EFI v1.10 only),
let's avoid the EFI v2.0 ones on all Apple x86 machines.

[0] https://lore.kernel.org/all/6D757C75-65B1-468B-842D-10410081A8E4@live.com/

Cc: <stable@vger.kernel.org>
Cc: Jeremy Kerr <jk@ozlabs.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Reported-by: Aditya Garg <gargaditya08@live.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Tested-by: Aditya Garg <gargaditya08@live.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215277
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udf: Fix NULL ptr deref when converting from inline format

commit 7fc3b7c2981bbd1047916ade327beccb90994eee upstream.

udf_expand_file_adinicb() calls directly ->writepage to write data
expanded into a page. This however misses to setup inode for writeback
properly and so we can crash on inode->i_wb dereference when submitting
page for IO like:

  BUG: kernel NULL pointer dereference, address: 0000000000000158
  #PF: supervisor read access in kernel mode
...
  <TASK>
  __folio_start_writeback+0x2ac/0x350
  __block_write_full_page+0x37d/0x490
  udf_expand_file_adinicb+0x255/0x400 [udf]
  udf_file_write_iter+0xbe/0x1b0 [udf]
  new_sync_write+0x125/0x1c0
  vfs_write+0x28e/0x400

Fix the problem by marking the page dirty and going through the standard
writeback path to write the page. Strictly speaking we would not even
have to write the page but we want to catch e.g. ENOSPC errors early.

Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 52ebea749aae ("writeback: make backing_dev_info host cgroup-specific bdi_writebacks")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udf: Restore i_lenAlloc when inode expansion fails

commit ea8569194b43f0f01f0a84c689388542c7254a1f upstream.

When we fail to expand inode from inline format to a normal format, we
restore inode to contain the original inline formatting but we forgot to
set i_lenAlloc back. The mismatch between i_lenAlloc and i_size was then
causing further problems such as warnings and lost data down the line.

Reported-by: butt3rflyh4ck <butterflyhuangxx@gmail.com>
CC: stable@vger.kernel.org
Fixes: 7e49b6f2480c ("udf: Convert UDF to new truncate calling sequence")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: zfcp: Fix failed recovery on gone remote port with non-NPIV FCP devices

commit 8c9db6679be4348b8aae108e11d4be2f83976e30 upstream.

Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.

Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.

Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.

We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale.  This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery.  For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.

This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached.  Then the related RSCN
triggered a successful port reopen recovery.  However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.

Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.

While the problem might have been in code before v2.6.32 commit
799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.

Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.

Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ucount: Make get_ucount a safe get_user replacement

commit f9d87929d451d3e649699d0f1d74f71f77ad38f5 upstream.

When the ucount code was refactored to create get_ucount it was missed
that some of the contexts in which a rlimit is kept elevated can be
the only reference to the user/ucount in the system.

Ordinary ucount references exist in places that also have a reference
to the user namspace, but in POSIX message queues, the SysV shm code,
and the SIGPENDING code there is no independent user namespace
reference.

Inspection of the the user_namespace show no instance of circular
references between struct ucounts and the user_namespace.  So
hold a reference from struct ucount to i's user_namespace to
resolve this problem.

Link: https://lore.kernel.org/lkml/YZV7Z+yXbsx9p3JN@fixkernel.com/
Reported-by: Qian Cai <quic_qiancai@quicinc.com>
Reported-by: Mathias Krause <minipli@grsecurity.net>
Tested-by: Mathias Krause <minipli@grsecurity.net>
Reviewed-by: Mathias Krause <minipli@grsecurity.net>
Reviewed-by: Alexey Gladkov <legion@kernel.org>
Fixes: d64696905554 ("Reimplement RLIMIT_SIGPENDING on top of ucounts")
Fixes: 6e52a9f0532f ("Reimplement RLIMIT_MSGQUEUE on top of ucounts")
Fixes: d7c9e99aee48 ("Reimplement RLIMIT_MEMLOCK on top of ucounts")
Cc: stable@vger.kernel.org
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/bpf: Update ldimm64 instructions during extra pass

commit f9320c49993ca3c0ec0f9a7026b313735306bb8b upstream.

These instructions are updated after the initial JIT, so redo codegen
during the extra pass. Rename bpf_jit_fixup_subprog_calls() to clarify
that this is more than just subprog calls.

Fixes: 69c087ba6225b5 ("bpf: Add bpf_for_each_map_elem() helper")
Cc: stable@vger.kernel.org # v5.15
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Tested-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/7cc162af77ba918eb3ecd26ec9e7824bc44b1fae.1641468127.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc32/bpf: Fix codegen for bpf-to-bpf calls

commit fab07611fb2e6a15fac05c4583045ca5582fd826 upstream.

Pad instructions emitted for BPF_CALL so that the number of instructions
generated does not change for different function addresses. This is
especially important for calls to other bpf functions, whose address
will only be known during extra pass.

Fixes: 51c66ad849a703 ("powerpc/bpf: Implement extended BPF on PPC32")
Cc: stable@vger.kernel.org # v5.13+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/52d8fe51f7620a6f27f377791564d79d75463576.1641468127.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bpf: Guard against accessing NULL pt_regs in bpf_get_task_stack()

commit b992f01e66150fc5e90be4a96f5eb8e634c8249e upstream.

task_pt_regs() can return NULL on powerpc for kernel threads. This is
then used in __bpf_get_stack() to check for user mode, resulting in a
kernel oops. Guard against this by checking return value of
task_pt_regs() before trying to obtain the call chain.

Fixes: fa28dcb82a38f8 ("bpf: Introduce helper bpf_get_task_stack()")
Cc: stable@vger.kernel.org # v5.9+
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/d5ef83c361cc255494afd15ff1b4fb02a36e1dcf.1641468127.git.naveen.n.rao@linux.vnet.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/nmi: handle vector validity failures for KVM guests

commit f094a39c6ba168f2df1edfd1731cca377af5f442 upstream.

The machine check validity bit tells about the context. If a KVM guest
was running the bit tells about the guest validity and the host state is
not affected. As a guest can disable the guest validity this might
result in unwanted host errors on machine checks.

Cc: stable@vger.kernel.org
Fixes: c929500d7a5a ("s390/nmi: s390: New low level handling for machine check happening in guest")
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/nmi: handle guarded storage validity failures for KVM guests

commit 1ea1d6a847d2b1d17fefd9196664b95f052a0775 upstream.

machine check validity bits reflect the state of the machine check. If a
guest does not make use of guarded storage, the validity bit might be
off. We can not use the host CR bit to decide if the validity bit must
be on. So ignore "invalid" guarded storage controls for KVM guests in
the host and rely on the machine check being forwarded to the guest.  If
no other errors happen from a host perspective everything is fine and no
process must be killed and the host can continue to run.

Cc: stable@vger.kernel.org
Fixes: c929500d7a5a ("s390/nmi: s390: New low level handling for machine check happening in guest")
Reported-by: Carsten Otte <cotte@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
Tested-by: Carsten Otte <cotte@de.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/hypfs: include z/VM guests with access control group set

commit 663d34c8df98740f1e90241e78e456d00b3c6cad upstream.

Currently if z/VM guest is allowed to retrieve hypervisor performance
data globally for all guests (privilege class B) the query is formed in a
way to include all guests but the group name is left empty. This leads to
that z/VM guests which have access control group set not being included
in the results (even local vm).

Change the query group identifier from empty to "any" to retrieve
information about all guests from any groups (or without a group set).

Cc: stable@vger.kernel.org
Fixes: 31cb4bd31a48 ("[S390] Hypervisor filesystem (s390_hypfs) for z/VM")
Reviewed-by: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/module: fix loading modules with a lot of relocations

commit f3b7e73b2c6619884351a3a0a7468642f852b8a2 upstream.

If the size of the PLT entries generated by apply_rela() exceeds
64KiB, the first ones can no longer reach __jump_r1 with brc. Fix by
using brcl. An alternative solution is to add a __jump_r1 copy after
every 64KiB, however, the space savings are quite small and do not
justify the additional complexity.

Fixes: f19fbd5ed642 ("s390: introduce execute-trampolines for branches")
Cc: stable@vger.kernel.org
Reported-by: Andrea Righi <andrea.righi@canonical.com>
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: arm64: Use shadow SPSR_EL1 when injecting exceptions on !VHE

commit 278583055a237270fac70518275ba877bf9e4013 upstream.

Injecting an exception into a guest with non-VHE is risky business.
Instead of writing in the shadow register for the switch code to
restore it, we override the CPU register instead. Which gets
overriden a few instructions later by said restore code.

The result is that although the guest correctly gets the exception,
it will return to the original context in some random state,
depending on what was there the first place... Boo.

Fix the issue by writing to the shadow register. The original code
is absolutely fine on VHE, as the state is already loaded, and writing
to the shadow register in that case would actually be a bug.

Fixes: bb666c472ca2 ("KVM: arm64: Inject AArch64 exceptions from HYP")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Fuad Tabba <tabba@google.com>
Link: https://lore.kernel.org/r/20220121184207.423426-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 9180/1: Thumb2: align ALT_UP() sections in modules sufficiently

commit 9f80ccda53b9417236945bc7ece4b519037df74d upstream.

When building for Thumb2, the .alt.smp.init sections that are emitted by
the ALT_UP() patching code may not be 32-bit aligned, even though the
fixup_smp_on_up() routine expects that. This results in alignment faults
at module load time, which need to be fixed up by the fault handler.

So let's align those sections explicitly, and prevent this from occurring.

Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: 9179/1: uaccess: avoid alignment faults in copy_[from|to]_kernel_nofault

commit 15420269b02a63ed8c1841905d8b8b2403246004 upstream.

The helpers that are used to implement copy_from_kernel_nofault() and
copy_to_kernel_nofault() cast a void* to a pointer to a wider type,
which may result in alignment faults on ARM if the compiler decides to
use double-word or multiple-word load/store instructions.

Only configurations that define CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS=y
are affected, given that commit 2423de2e6f4d ("ARM: 9115/1: mm/maccess:
fix unaligned copy_{from,to}_kernel_nofault") ensures that dst and src
are sufficiently aligned otherwise.

So use the unaligned accessors for accessing dst and src in cases where
they may be misaligned.

Cc: <stable@vger.kernel.org> # depends on 2423de2e6f4d
Fixes: 2df4c9a741a0 ("ARM: 9112/1: uaccess: add __{get,put}_kernel_nofault")
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: skip only stmmac_ptp_register when resume from suspend

commit 0735e639f129dff455aeb91da291f5c578cc33db upstream.

When resume from suspend, besides skipping PTP registration, it also
skipping PTP HW initialization. This could cause PTP clock not able to
operate properly when resume from suspend.

To fix this, only stmmac_ptp_register() is skipped when resume from
suspend.

Fixes: fe1319291150 ("stmmac: Don't init ptp again when resume from suspend/hibernation")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: configure PTP clock source prior to PTP initialization

commit 94c82de43e01ef5747a95e4a590880de863fe423 upstream.

For Intel platform, it is required to configure PTP clock source prior PTP
initialization in MAC. So, need to move ptp_clk_freq_config execution from
stmmac_ptp_register() to stmmac_init_ptp().

Fixes: 76da35dc99af ("stmmac: intel: Add PSE and PCH PTP clock source selection")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: sfp: ignore disabled SFP node

commit 2148927e6ed43a1667baf7c2ae3e0e05a44b51a0 upstream.

Commit ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).

We need to ignore disabled SFP bus node.

Fixes: ce0aa27ff3f6 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: m_can: m_can_fifo_{read,write}: don't read or write from/to FIFO if length is 0

commit db72589c49fd260bfc99c7160c079675bc7417af upstream.

In order to optimize FIFO access, especially on m_can cores attached
to slow busses like SPI, in patch

| e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")

bulk read/write support has been added to the m_can_fifo_{read,write}
functions.

That change leads to the tcan driver to call
regmap_bulk_{read,write}() with a length of 0 (for CAN frames with 0
data length). regmap treats this as an error:

| tcan4x5x spi1.0 tcan4x5x0: FIFO write returned -22

This patch fixes the problem by not calling the
cdev->ops->{read,write)_fifo() in case of a 0 length read/write.

Fixes: e39381770ec9 ("can: m_can: Disable IRQs on FIFO bus errors")
Link: https://lore.kernel.org/all/20220114155751.2651888-1-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Cc: Matt Kline <matt@bitbashing.io>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Reported-by: Michael Anochin <anochin@photo-meter.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 5.15.18

Link: https://lore.kernel.org/r/20220127180259.078563735@linuxfoundation.org
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Shuah Khan <skhan@linuxfoundation.org>
Tested-by: Ron Economos <re@w6rz.net>
Tested-by: Linux Kernel Functional Testing <lkft@linaro.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Fox Chen <foxhlchen@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vmwgfx: Fix stale file descriptors on failed usercopy

commit a0f90c8815706981c483a652a6aefca51a5e191c upstream.

A failing usercopy of the fence_rep object will lead to a stale entry in
the file descriptor table as put_unused_fd() won't release it. This
enables userland to refer to a dangling 'file' object through that still
valid file descriptor, leading to all kinds of use-after-free
exploitation scenarios.

Fix this by deferring the call to fd_install() until after the usercopy
has succeeded.

Fixes: c906965dee22 ("drm/vmwgfx: Add export fence to file descriptor support")
Signed-off-by: Mathias Krause <minipli@grsecurity.net>
Signed-off-by: Zack Rusin <zackr@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64/bpf: Remove 128MB limit for BPF JIT programs

commit b89ddf4cca43f1269093942cf5c4e457fd45c335 upstream.

Commit 91fc957c9b1d ("arm64/bpf: don't allocate BPF JIT programs in module
memory") restricts BPF JIT program allocation to a 128MB region to ensure
BPF programs are still in branching range of each other. However this
restriction should not apply to the aarch64 JIT, since BPF_JMP | BPF_CALL
are implemented as a 64-bit move into a register and then a BLR instruction -
which has the effect of being able to call anything without proximity
limitation.

The practical reason to relax this restriction on JIT memory is that 128MB of
JIT memory can be quickly exhausted, especially where PAGE_SIZE is 64KB - one
page is needed per program. In cases where seccomp filters are applied to
multiple VMs on VM launch - such filters are classic BPF but converted to
BPF - this can severely limit the number of VMs that can be launched. In a
world where we support BPF JIT always on, turning off the JIT isn't always an
option either.

Fixes: 91fc957c9b1d ("arm64/bpf: don't allocate BPF JIT programs in module memory")
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <russell.king@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Alan Maguire <alan.maguire@oracle.com>
Link: https://lore.kernel.org/bpf/1636131046-5982-2-git-send-email-alan.maguire@oracle.com
Reviewed-by: Tom Saeger <tom.saeger@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/amdgpu: Use correct VIEWPORT_DIMENSION for DCN2

commit dc5d4aff2e99c312df8abbe1ee9a731d2913bc1b upstream.

For some reason this file isn't using the appropriate register
headers for DCN headers, which means that on DCN2 we're getting
the VIEWPORT_DIMENSION offset wrong.

This means that we're not correctly carving out the framebuffer
memory correctly for a framebuffer allocated by EFI and
therefore see corruption when loading amdgpu before the display
driver takes over control of the framebuffer scanout.

Fix this by checking the DCE_HWIP and picking the correct offset
accordingly.

Long-term we should expose this info from DC as GMC shouldn't
need to know about DCN registers.

Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

select: Fix indefinitely sleeping task in poll_schedule_timeout()

commit 68514dacf2715d11b91ca50d88de047c086fea9c upstream.

A task can end up indefinitely sleeping in do_select() ->
poll_schedule_timeout() when the following race happens:

  TASK1 (thread1)             TASK2                   TASK1 (thread2)
  do_select()
    setup poll_wqueues table
    with 'fd'
                              write data to 'fd'
                                pollwake()
                                  table->triggered = 1
                                                      closes 'fd' thread1 is
                                                        waiting for
    poll_schedule_timeout()
      - sees table->triggered
      table->triggered = 0
      return -EINTR
    loop back in do_select()

But at this point when TASK1 loops back, the fdget() in the setup of
poll_wqueues fails.  So now so we never find 'fd' is ready for reading
and sleep in poll_schedule_timeout() indefinitely.

Treat an fd that got closed as a fd on which some event happened.  This
makes sure cannot block indefinitely in do_select().

Another option would be to return -EBADF in this case but that has a
potential of subtly breaking applications that excercise this behavior
and it happens to work for them.  So returning fd as active seems like a
safer choice.

Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rcu: Tighten rcu_advance_cbs_nowake() checks

commit 614ddad17f22a22e035e2ea37a04815f50362017 upstream.

Currently, rcu_advance_cbs_nowake() checks that a grace period is in
progress, however, that grace period could end just after the check.
This commit rechecks that a grace period is still in progress while
holding the rcu_node structure's lock.  The grace period cannot end while
the current CPU's rcu_node structure's ->lock is held, thus avoiding
false positives from the WARN_ON_ONCE().

As Daniel Vacek noted, it is not necessary for the rcu_node structure
to have a CPU that has not yet passed through its quiescent state.

Tested-by: Guillaume Morin <guillaume@morinfr.org>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memcg: better bounds on the memcg stats updates

commit 5b3be698a872c490dbed524f3e2463701ab21339 upstream.

Commit 11192d9c124d ("memcg: flush stats only if updated") added
tracking of memcg stats updates which is used by the readers to flush
only if the updates are over a certain threshold.  However each
individual update can correspond to a large value change for a given
stat.  For example adding or removing a hugepage to an LRU changes the
stat by thp_nr_pages (512 on x86_64).

Treating the update related to THP as one can keep the stat off, in
theory, by (thp_nr_pages * nr_cpus * CHARGE_BATCH) before flush.

To handle such scenarios, this patch adds consideration of the stat
update value as well instead of just the update event.  In addition let
the asyn flusher unconditionally flush the stats to put time limit on
the stats skew and hopefully a lot less readers would need to flush.

Link: https://lkml.kernel.org/r/20211118065350.697046-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Michal Koutný" <mkoutny@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

memcg: unify memcg stat flushing

commit fd25a9e0e23b995fd0ba5e2f00a1099452cbc3cf upstream.

The memcg stats can be flushed in multiple context and potentially in
parallel too.  For example multiple parallel user space readers for
memcg stats will contend on the rstat locks with each other.  There is
no need for that.  We just need one flusher and everyone else can
benefit.

In addition after aa48e47e3906 ("memcg: infrastructure to flush memcg
stats") the kernel periodically flush the memcg stats from the root, so,
the other flushers will potentially have much less work to do.

Link: https://lkml.kernel.org/r/20211001190040.48086-2-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Michal Koutný" <mkoutny@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>