drivers: net: ethernet: cpsw: use netif_wake_queue() while restarting tx queue

[ Upstream commit b56d6b3fca6d1214dbc9c5655f26e5d4ec04afc8 ]

To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.

Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers: net: ethernet: davinci_emac: use netif_wake_queue() while restarting tx queue

To restart tx queue use netif_wake_queue() intead of netif_start_queue()
so that net schedule will restart transmission immediately which will
increase network performance while doing huge data transfers.

Reported-by: Dan Franke <dan.franke@schneider-electric.com>
Suggested-by: Sriramakrishnan A G <srk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: fix disabling of arp_interval and miimon

[ Upstream commit 1bc7db16782c2a581fb4d53ca853631050f31611 ]

Currently if either arp_interval or miimon is disabled, they both get
disabled, and upon disabling they get executed once more which is not
the proper behaviour. Also when doing a no-op and disabling an already
disabled one, the other again gets disabled.
Also fix the error messages with the proper valid ranges, and a small
typo fix in the up delay error message (outputting "down delay", instead
of "up delay").

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: fix miimon and arp_interval delayed work race conditions

[ Upstream commit fbb0c41b814d497c656fc7be9e35456f139cb2fb ]

First I would give three observations which will be used later.
Observation 1: if (delayed_work_pending(wq)) cancel_delayed_work(wq)
 This usage is wrong because the pending bit is cleared just before the
 work's fn is executed and if the function re-arms itself we might end up
 with the work still running. It's safe to call cancel_delayed_work_sync()
 even if the work is not queued at all.
Observation 2: Use of INIT_DELAYED_WORK()
 Work needs to be initialized only once prior to (de/en)queueing.
Observation 3: IFF_UP is set only after ndo_open is called

Related race conditions:
1. Race between bonding_store_miimon() and bonding_store_arp_interval()
 Because of Obs.1 we can end up having both works enqueued.
2. Multiple races with INIT_DELAYED_WORK()
 Since the works are not protected by anything between INIT_DELAYED_WORK()
 and calls to (en/de)queue it is possible for races between the following
 functions:
 (races are also possible between the calls to INIT_DELAYED_WORK()
  and workqueue code)
 bonding_store_miimon() - bonding_store_arp_interval(), bond_close(),
  bond_open(), enqueued functions
 bonding_store_arp_interval() - bonding_store_miimon(), bond_close(),
bond_open(), enqueued functions
3. By Obs.1 we need to change bond_cancel_all()

Bugs 1 and 2 are fixed by moving all work initializations in bond_open
which by Obs. 2 and Obs. 3 and the fact that we make sure that all works
are cancelled in bond_close(), is guaranteed not to have any work
enqueued.
Also RTNL lock is now acquired in bonding_store_miimon/arp_interval so
they can't race with bond_close and bond_open. The opposing work is
cancelled only if the IFF_UP flag is set and it is cancelled
unconditionally. The opposing work is already cancelled if the interface
is down so no need to cancel it again. This way we don't need new
synchronizations for the bonding workqueue. These bugs (and fixes) are
tied together and belong in the same patch.
Note: I have left 1 line intentionally over 80 characters (84) because I
      didn't like how it looks broken down. If you'd prefer it otherwise,
      then simply break it.

 v2: Make description text < 75 columns

Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bonding: remove already created master sysfs link on failure

[ Upstream commit 9fe16b78ee17579cb4f333534cf7043e94c67024 ]

If slave sysfs symlink failes to be created - we end up without removing
the master sysfs symlink. Remove it in case of failure.

Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

unix: fix a race condition in unix_release()

[ Upstream commit ded34e0fe8fe8c2d595bfa30626654e4b87621e0 ]

As reported by Jan, and others over the past few years, there is a
race condition caused by unix_release setting the sock->sk pointer
to NULL before properly marking the socket as dead/orphaned.  This
can cause a problem with the LSM hook security_unix_may_send() if
there is another socket attempting to write to this partially
released socket in between when sock->sk is set to NULL and it is
marked as dead/orphaned.  This patch fixes this by only setting
sock->sk to NULL after the socket has been marked as dead; I also
take the opportunity to make unix_release_sock() a void function
as it only ever returned 0/success.

Dave, I think this one should go on the -stable pile.

Special thanks to Jan for coming up with a reproducer for this
problem.

Reported-by: Jan Stancek <jan.stancek@gmail.com>
Signed-off-by: Paul Moore <pmoore@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

thermal: shorten too long mcast group name

[ Upstream commits 73214f5d9f33b79918b1f7babddd5c8af28dd23d
  and f1e79e208076ffe7bad97158275f1c572c04f5c7, the latter
  adds an assertion to genetlink to prevent this from happening
  again in the future. ]

The original name is too long.

Signed-off-by: Masatake YAMATO <yamato@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

8021q: fix a potential use-after-free

[ Upstream commit 4a7df340ed1bac190c124c1601bfc10cde9fb4fb ]

vlan_vid_del() could possibly free ->vlan_info after a RCU grace
period, however, we may still refer to the freed memory area
by 'grp' pointer. Found by code inspection.

This patch moves vlan_vid_del() as behind as possible.

Signed-off-by: Cong Wang <amwang@redhat.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: undo spurious timeout after SACK reneging

[ Upstream commit 7ebe183c6d444ef5587d803b64a1f4734b18c564 ]

On SACK reneging the sender immediately retransmits and forces a
timeout but disables Eifel (undo). If the (buggy) receiver does not
drop any packet this can trigger a false slow-start retransmit storm
driven by the ACKs of the original packets. This can be detected with
undo and TCP timestamps.

Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tcp: preserve ACK clocking in TSO

[ Upstream commit f4541d60a449afd40448b06496dcd510f505928e ]

A long standing problem with TSO is the fact that tcp_tso_should_defer()
rearms the deferred timer, while it should not.

Current code leads to following bad bursty behavior :

20:11:24.484333 IP A > B: . 297161:316921(19760) ack 1 win 119
20:11:24.484337 IP B > A: . ack 263721 win 1117
20:11:24.485086 IP B > A: . ack 265241 win 1117
20:11:24.485925 IP B > A: . ack 266761 win 1117
20:11:24.486759 IP B > A: . ack 268281 win 1117
20:11:24.487594 IP B > A: . ack 269801 win 1117
20:11:24.488430 IP B > A: . ack 271321 win 1117
20:11:24.489267 IP B > A: . ack 272841 win 1117
20:11:24.490104 IP B > A: . ack 274361 win 1117
20:11:24.490939 IP B > A: . ack 275881 win 1117
20:11:24.491775 IP B > A: . ack 277401 win 1117
20:11:24.491784 IP A > B: . 316921:332881(15960) ack 1 win 119
20:11:24.492620 IP B > A: . ack 278921 win 1117
20:11:24.493448 IP B > A: . ack 280441 win 1117
20:11:24.494286 IP B > A: . ack 281961 win 1117
20:11:24.495122 IP B > A: . ack 283481 win 1117
20:11:24.495958 IP B > A: . ack 285001 win 1117
20:11:24.496791 IP B > A: . ack 286521 win 1117
20:11:24.497628 IP B > A: . ack 288041 win 1117
20:11:24.498459 IP B > A: . ack 289561 win 1117
20:11:24.499296 IP B > A: . ack 291081 win 1117
20:11:24.500133 IP B > A: . ack 292601 win 1117
20:11:24.500970 IP B > A: . ack 294121 win 1117
20:11:24.501388 IP B > A: . ack 295641 win 1117
20:11:24.501398 IP A > B: . 332881:351881(19000) ack 1 win 119

While the expected behavior is more like :

20:19:49.259620 IP A > B: . 197601:202161(4560) ack 1 win 119
20:19:49.260446 IP B > A: . ack 154281 win 1212
20:19:49.261282 IP B > A: . ack 155801 win 1212
20:19:49.262125 IP B > A: . ack 157321 win 1212
20:19:49.262136 IP A > B: . 202161:206721(4560) ack 1 win 119
20:19:49.262958 IP B > A: . ack 158841 win 1212
20:19:49.263795 IP B > A: . ack 160361 win 1212
20:19:49.264628 IP B > A: . ack 161881 win 1212
20:19:49.264637 IP A > B: . 206721:211281(4560) ack 1 win 119
20:19:49.265465 IP B > A: . ack 163401 win 1212
20:19:49.265886 IP B > A: . ack 164921 win 1212
20:19:49.266722 IP B > A: . ack 166441 win 1212
20:19:49.266732 IP A > B: . 211281:215841(4560) ack 1 win 119
20:19:49.267559 IP B > A: . ack 167961 win 1212
20:19:49.268394 IP B > A: . ack 169481 win 1212
20:19:49.269232 IP B > A: . ack 171001 win 1212
20:19:49.269241 IP A > B: . 215841:221161(5320) ack 1 win 119

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Van Jacobson <vanj@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sky2: Threshold for Pause Packet is set wrong

[ Upstream commit 74f9f42c1c1650e74fb464f76644c9041f996851 ]

The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a
wrong value which leads to only 2kB of RAM remaining space. This can lead to
Rx overflow errors even with activated flow-control.

Fix: We should increase the value to 8192/8

Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sky2: Receive Overflows not counted

[ Upstream commit 9cfe8b156c21cf340b3a10ecb3022fbbc1c39185 ]

The sky2 driver doesn't count the Receive Overflows because the MAC
interrupt for this event is not set in the MAC's interrupt mask.
The MAC's interrupt mask is set only for Transmit FIFO Underruns.

Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR)
Otherwise the Receive Overflow event will not generate any interrupt.
The  Receive Overflow interrupt is handled correctly

Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: remove a WARN_ON() in net_enable_timestamp()

[ Upstream commit 9979a55a833883242e3a29f3596676edd7199c46 ]

The WARN_ON(in_interrupt()) in net_enable_timestamp() can get false
positive, in socket clone path, run from softirq context :

[ 3641.624425] WARNING: at net/core/dev.c:1532 net_enable_timestamp+0x7b/0x80()
[ 3641.668811] Call Trace:
[ 3641.671254]  <IRQ>  [<ffffffff80286817>] warn_slowpath_common+0x87/0xc0
[ 3641.677871]  [<ffffffff8028686a>] warn_slowpath_null+0x1a/0x20
[ 3641.683683]  [<ffffffff80742f8b>] net_enable_timestamp+0x7b/0x80
[ 3641.689668]  [<ffffffff80732ce5>] sk_clone_lock+0x425/0x450
[ 3641.695222]  [<ffffffff8078db36>] inet_csk_clone_lock+0x16/0x170
[ 3641.701213]  [<ffffffff807ae449>] tcp_create_openreq_child+0x29/0x820
[ 3641.707663]  [<ffffffff807d62e2>] ? ipt_do_table+0x222/0x670
[ 3641.713354]  [<ffffffff807aaf5b>] tcp_v4_syn_recv_sock+0xab/0x3d0
[ 3641.719425]  [<ffffffff807af63a>] tcp_check_req+0x3da/0x530
[ 3641.724979]  [<ffffffff8078b400>] ? inet_hashinfo_init+0x60/0x80
[ 3641.730964]  [<ffffffff807ade6f>] ? tcp_v4_rcv+0x79f/0xbe0
[ 3641.736430]  [<ffffffff807ab9bd>] tcp_v4_do_rcv+0x38d/0x4f0
[ 3641.741985]  [<ffffffff807ae14a>] tcp_v4_rcv+0xa7a/0xbe0

Its safe at this point because the parent socket owns a reference
on the netstamp_needed, so we cant have a 0 -> 1 transition, which
requires to lock a mutex.

Instead of refining the check, lets remove it, as all known callers
are safe. If it ever changes in the future, static_key_slow_inc()
will complain anyway.

Reported-by: Laurent Chavey <chavey@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Prevent buffer overwrite disabled for latency tracers

commit 613f04a0f51e6e68ac6fe571ab79da3c0a5eb4da upstream.

The latency tracers require the buffers to be in overwrite mode,
otherwise they get screwed up. Force the buffers to stay in overwrite
mode when latency tracers are enabled.

Added a flag_changed() method to the tracer structure to allow
the tracers to see what flags are being changed, and also be able
to prevent the change from happing.

[Backported for 3.4-stable. Re-added current_trace NULL checks; removed
allocated_snapshot field; adapted to tracing_trace_options_write without
trace_set_options.]

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Protect tracer flags with trace_types_lock

commit 69d34da2984c95b33ea21518227e1f9470f11d95 upstream.

Seems that the tracer flags have never been protected from
synchronous writes. Luckily, admins don't usually modify the
tracing flags via two different tasks. But if scripts were to
be used to modify them, then they could get corrupted.

Move the trace_types_lock that protects against tracers changing
to also protect the flags being set.

[Backported for 3.4, 3.0-stable. Moved return to after unlock.]

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: use atomic64_t for the per-flexbg free_clusters count

commit 90ba983f6889e65a3b506b30dc606aa9d1d46cd2 upstream.

A user who was using a 8TB+ file system and with a very large flexbg
size (> 65536) could cause the atomic_t used in the struct flex_groups
to overflow.  This was detected by PaX security patchset:

http://forums.grsecurity.net/viewtopic.php?f=3&t=3289&p=12551#p12551

This bug was introduced in commit 9f24e4208f7e, so it's been around
since 2.6.30.  :-(

Fix this by using an atomic64_t for struct orlav_stats's
free_clusters.

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: convert number of blocks to clusters properly

commit 810da240f221d64bf90020f25941b05b378186fe upstream.

We're using macro EXT4_B2C() to convert number of blocks to number of
clusters for bigalloc file systems.  However, we should be using
EXT4_NUM_B2C().

Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efivars: Handle duplicate names from get_next_variable()

commit e971318bbed610e28bb3fde9d548e6aaf0a6b02e upstream.

Some firmware exhibits a bug where the same VariableName and
VendorGuid values are returned on multiple invocations of
GetNextVariableName(). See,

    https://bugzilla.kernel.org/show_bug.cgi?id=47631

As a consequence of such a bug, Andre reports hitting the following
WARN_ON() in the sysfs code after updating the BIOS on his, "Gigabyte
Technology Co., Ltd. To be filled by O.E.M./Z77X-UD3H, BIOS F19e
11/21/2012)" machine,

[    0.581554] EFI Variables Facility v0.08 2004-May-17
[    0.584914] ------------[ cut here ]------------
[    0.585639] WARNING: at /home/andre/linux/fs/sysfs/dir.c:536 sysfs_add_one+0xd4/0x100()
[    0.586381] Hardware name: To be filled by O.E.M.
[    0.587123] sysfs: cannot create duplicate filename '/firmware/efi/vars/SbAslBufferPtrVar-01f33c25-764d-43ea-aeea-6b5a41f3f3e8'
[    0.588694] Modules linked in:
[    0.589484] Pid: 1, comm: swapper/0 Not tainted 3.8.0+ #7
[    0.590280] Call Trace:
[    0.591066]  [<ffffffff81208954>] ? sysfs_add_one+0xd4/0x100
[    0.591861]  [<ffffffff810587bf>] warn_slowpath_common+0x7f/0xc0
[    0.592650]  [<ffffffff810588bc>] warn_slowpath_fmt+0x4c/0x50
[    0.593429]  [<ffffffff8134dd85>] ? strlcat+0x65/0x80
[    0.594203]  [<ffffffff81208954>] sysfs_add_one+0xd4/0x100
[    0.594979]  [<ffffffff81208b78>] create_dir+0x78/0xd0
[    0.595753]  [<ffffffff81208ec6>] sysfs_create_dir+0x86/0xe0
[    0.596532]  [<ffffffff81347e4c>] kobject_add_internal+0x9c/0x220
[    0.597310]  [<ffffffff81348307>] kobject_init_and_add+0x67/0x90
[    0.598083]  [<ffffffff81584a71>] ? efivar_create_sysfs_entry+0x61/0x1c0
[    0.598859]  [<ffffffff81584b2b>] efivar_create_sysfs_entry+0x11b/0x1c0
[    0.599631]  [<ffffffff8158517e>] register_efivars+0xde/0x420
[    0.600395]  [<ffffffff81d430a7>] ? edd_init+0x2f5/0x2f5
[    0.601150]  [<ffffffff81d4315f>] efivars_init+0xb8/0x104
[    0.601903]  [<ffffffff8100215a>] do_one_initcall+0x12a/0x180
[    0.602659]  [<ffffffff81d05d80>] kernel_init_freeable+0x13e/0x1c6
[    0.603418]  [<ffffffff81d05586>] ? loglevel+0x31/0x31
[    0.604183]  [<ffffffff816a6530>] ? rest_init+0x80/0x80
[    0.604936]  [<ffffffff816a653e>] kernel_init+0xe/0xf0
[    0.605681]  [<ffffffff816ce7ec>] ret_from_fork+0x7c/0xb0
[    0.606414]  [<ffffffff816a6530>] ? rest_init+0x80/0x80
[    0.607143] ---[ end trace 1609741ab737eb29 ]---

There's not much we can do to work around and keep traversing the
variable list once we hit this firmware bug. Our only solution is to
terminate the loop because, as Lingzhu reports, some machines get
stuck when they encounter duplicate names,

  > I had an IBM System x3100 M4 and x3850 X5 on which kernel would
  > get stuck in infinite loop creating duplicate sysfs files because,
  > for some reason, there are several duplicate boot entries in nvram
  > getting GetNextVariableName into a circle of iteration (with
  > period > 2).

Also disable the workqueue, as efivar_update_sysfs_entries() uses
GetNextVariableName() to figure out which variables have been created
since the last iteration. That algorithm isn't going to work if
GetNextVariableName() returns duplicates. Note that we don't disable
EFI variable creation completely on the affected machines, it's just
that any pstore dump-* files won't appear in sysfs until the next
boot.

[Backported for 3.4-stable. Removed code related to pstore
workqueue but pulled in helper function variable_is_present
from a93bc0c; Moved the definition of __efivars to the top
for being referenced in variable_is_present.]

Reported-by: Andre Heider <a.heider@gmail.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Tested-by: Lingzhu Xiang <lxiang@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

efivars: explicitly calculate length of VariableName

commit ec50bd32f1672d38ddce10fb1841cbfda89cfe9a upstream.

It's not wise to assume VariableNameSize represents the length of
VariableName, as not all firmware updates VariableNameSize in the same
way (some don't update it at all if EFI_SUCCESS is returned). There
are even implementations out there that update VariableNameSize with
values that are both larger than the string returned in VariableName
and smaller than the buffer passed to GetNextVariableName(), which
resulted in the following bug report from Michael Schroeder,

  > On HP z220 system (firmware version 1.54), some EFI variables are
  > incorrectly named :
  >
  > ls -d /sys/firmware/efi/vars/*8be4d* | grep -v -- -8be returns
  > /sys/firmware/efi/vars/dbxDefault-pport8be4df61-93ca-11d2-aa0d-00e098032b8c
  > /sys/firmware/efi/vars/KEKDefault-pport8be4df61-93ca-11d2-aa0d-00e098032b8c
  > /sys/firmware/efi/vars/SecureBoot-pport8be4df61-93ca-11d2-aa0d-00e098032b8c
  > /sys/firmware/efi/vars/SetupMode-Information8be4df61-93ca-11d2-aa0d-00e098032b8c

The issue here is that because we blindly use VariableNameSize without
verifying its value, we can potentially read garbage values from the
buffer containing VariableName if VariableNameSize is larger than the
length of VariableName.

Since VariableName is a string, we can calculate its size by searching
for the terminating NULL character.

[Backported for 3.8-stable. Removed workqueue code added in
a93bc0c 3.9-rc1.]

Reported-by: Frederic Crozat <fcrozat@suse.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Michael Schroeder <mls@suse.com>
Cc: Lee, Chun-Yi <jlee@suse.com>
Cc: Lingzhu Xiang <lxiang@redhat.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: fix space leak when we fail to reserve metadata space

commit f4881bc7a83eff263789dd524b7c269d138d4af5 upstream.

Dave reported a warning when running xfstest 275.  We have been leaking delalloc
metadata space when our reservations fail.  This is because we were improperly
calculating how much space to free for our checksum reservations.  The problem
is we would sometimes free up space that had already been freed in another
thread and we would end up with negative usage for the delalloc space.  This
patch fixes the problem by calculating how much space the other threads would
have already freed, and then calculate how much space we need to free had we not
done the reservation at all, and then freeing any excess space.  This makes
xfstests 275 no longer have leaked space.  Thanks

Reported-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Don't clobber crtc->fb when queue_flip fails

commit 4a35f83b2b7c6aae3fc0d1c4554fdc99dc33ad07 upstream.

Restore crtc->fb to the old framebuffer if queue_flip fails.

While at it, kill the pointless intel_fb temp variable.

v2: Update crtc->fb before queue_flip and restore it back
    after a failure.

Backported for 3.4-stable. Adjusted context only.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfsd4: reject "negative" acl lengths

commit 64a817cfbded8674f345d1117b117f942a351a69 upstream.

Since we only enforce an upper bound, not a lower bound, a "negative"
length can get through here.

The symptom seen was a warning when we attempt to a kmalloc with an
excessive size.

Reported-by: Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: cns3xxx: fix mapping of private memory region

commit a3d9052c6296ad3398d3ad649c3c682c3e7ecfa6 upstream.

Since commit 0536bdf33faf (ARM: move iotable mappings within the vmalloc
region), the Cavium CNS3xxx cannot boot anymore.

This is caused by the pre-defined iotable mappings is not in the vmalloc
region. This patch move the iotable mappings into the vmalloc region, and
merge the MPCore private memory region (containing the SCU, the GIC and
the TWD) as a single region.

Signed-off-by: Mac Lin <mkl0301@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

loop: prevent bdev freeing while device in use

commit c1681bf8a7b1b98edee8b862a42c19c4e53205fd upstream.

struct block_device lifecycle is defined by its inode (see fs/block_dev.c) -
block_device allocated first time we access /dev/loopXX and deallocated on
bdev_destroy_inode. When we create the device "losetup /dev/loopXX afile"
we want that block_device stay alive until we destroy the loop device
with "losetup -d".

But because we do not hold /dev/loopXX inode its counter goes 0, and
inode/bdev can be destroyed at any moment. Usually it happens at memory
pressure or when user drops inode cache (like in the test below). When later in
loop_clr_fd() we want to use bdev we have use-after-free error with following
stack:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000280
  bd_set_size+0x10/0xa0
  loop_clr_fd+0x1f8/0x420 [loop]
  lo_ioctl+0x200/0x7e0 [loop]
  lo_compat_ioctl+0x47/0xe0 [loop]
  compat_blkdev_ioctl+0x341/0x1290
  do_filp_open+0x42/0xa0
  compat_sys_ioctl+0xc1/0xf20
  do_sys_open+0x16e/0x1d0
  sysenter_dispatch+0x7/0x1a

To prevent use-after-free we need to grab the device in loop_set_fd()
and put it later in loop_clr_fd().

The issue is reprodusible on current Linus head and v3.3. Here is the test:

  dd if=/dev/zero of=loop.file bs=1M count=1
  while [ true ]; do
    losetup /dev/loop0 loop.file
    echo 2 > /proc/sys/vm/drop_caches
    losetup -d /dev/loop0
  done

[ Doing bdgrab/bput in loop_set_fd/loop_clr_fd is safe, because every
  time we call loop_set_fd() we check that loop_device->lo_state is
  Lo_unbound and set it to Lo_bound If somebody will try to set_fd again
  it will get EBUSY.  And if we try to loop_clr_fd() on unbound loop
  device we'll get ENXIO.

  loop_set_fd/loop_clr_fd (and any other loop ioctl) is called under
  loop_device->lo_ctl_mutex. ]

Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: gadget: udc-core: fix a regression during gadget driver unbinding

commit 511f3c5326eabe1ece35202a404c24c0aeacc246 upstream.

This patch (as1666) fixes a regression in the UDC core.  The core
takes care of unbinding gadget drivers, and it does the unbinding
before telling the UDC driver to turn off the controller hardware.
When the call to the udc_stop callback is made, the gadget no longer
has a driver.  The callback routine should not be invoked with a
pointer to the old driver; doing so can cause problems (such as
use-after-free accesses in net2280).

This patch should be applied, with appropriate context changes, to all
the stable kernels going back to 3.1.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: don't drop path when printing out tree errors in scrub

commit d8fe29e9dea8d7d61fd140d8779326856478fc62 upstream.

A user reported a panic where we were panicing somewhere in
tree_backref_for_extent from scrub_print_warning.  He only captured the trace
but looking at scrub_print_warning we drop the path right before we mess with
the extent buffer to print out a bunch of stuff, which isn't right.  So fix this
by dropping the path after we use the eb if we need to.  Thanks,

Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: limit the global reserve to 512mb

commit fdf30d1c1b386e1b73116cc7e0fb14e962b763b0 upstream.

A user reported a problem where he was getting early ENOSPC with hundreds of
gigs of free data space and 6 gigs of free metadata space.  This is because the
global block reserve was taking up the entire free metadata space.  This is
ridiculous, we have infrastructure in place to throttle if we start using too
much of the global reserve, so instead of letting it get this huge just limit it
to 512mb so that users can still get work done.  This allowed the user to
complete his rsync without issues.  Thanks

Reported-and-tested-by: Stefan Priebe <s.priebe@profihost.ag>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: fix race between mmap writes and compression

commit 4adaa611020fa6ac65b0ac8db78276af4ec04e63 upstream.

Btrfs uses page_mkwrite to ensure stable pages during
crc calculations and mmap workloads.  We call clear_page_dirty_for_io
before we do any crcs, and this forces any application with the file
mapped to wait for the crc to finish before it is allowed to change
the file.

With compression on, the clear_page_dirty_for_io step is happening after
we've compressed the pages.  This means the applications might be
changing the pages while we are compressing them, and some of those
modifications might not hit the disk.

This commit adds the clear_page_dirty_for_io before compression starts
and makes sure to redirty the page if we have to fallback to
uncompressed IO as well.

Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Reported-by: Alexandre Oliva <oliva@gnu.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: xhci: Fix TRB transfer length macro used for Event TRB.

commit 1c11a172cb30492f5f6a82c6e118fdcd9946c34f upstream.

Use proper macro while extracting TRB transfer length from
Transfer event TRBs. Adding a macro EVENT_TRB_LEN (bits 0:23)
for the same, and use it instead of TRB_LEN (bits 0:16) in
case of event TRBs.

This patch should be backported to kernels as old as 2.6.31, that
contain the commit b10de142119a676552df3f0d2e3a9d647036c26a "USB: xhci:
Bulk transfer support".  This patch will have issues applying to older
kernels.

Signed-off-by: Vivek gautam <gautam.vivek@samsung.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/irda: add missing error path release_sock call

commit 896ee0eee6261e30c3623be931c3f621428947df upstream.

This makes sure that release_sock is called for all error conditions in
irda_getsockopt.

Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Brad Spengler <spender@grsecurity.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

pnfs-block: removing DM device maybe cause oops when call dev_remove

commit 4376c94618c26225e69e17b7c91169c45a90b292 upstream.

when pnfs block using device mapper,if umounting later,it maybe
cause oops. we apply "1 + sizeof(bl_umount_request)" memory for
msg->data, the memory maybe overflow when we do "memcpy(&dataptr
[sizeof(bl_msg)], &bl_umount_request, sizeof(bl_umount_request))",
because the size of bl_msg is more than 1 byte.

Signed-off-by: fanchaoting<fanchaoting@cn.fujitsu.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: cancel cmd timer and free curr_cmd in shutdown process

commit 084c7189acb3f969c855536166042e27f5dd703f upstream.

curr_cmd points to the command that is in processing or waiting
for its command response from firmware. If the function shutdown
happens to occur at this time we should cancel the cmd timer and
put the command back to free queue.

Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

vt: synchronize_rcu() under spinlock is not nice...

commit e8cd81693bbbb15db57d3c9aa7dd90eda4842874 upstream.

vcs_poll_data_free() calls unregister_vt_notifier(), which calls
atomic_notifier_chain_unregister(), which calls synchronize_rcu().
Do it *after* we'd dropped ->f_lock.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD

commit 482b0b5d82bd916cc0c55a2abf65bdc69023b843 upstream.

It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW

Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tty: atmel_serial_probe(): index of atmel_ports[] fix

commit 503bded92da283b2f31d87e054c4c6d30c3c2340 upstream.

Index of atmel_ports[ATMEL_MAX_UART] should be smaller
than ATMEL_MAX_UART.

Signed-off-by: Pawel Wieczorkiewicz <wpawel@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-blkback: fix dispatch_rw_block_io() error path

commit 0e5e098ac22dae38f957e951b70d3cf73beff0f7 upstream.

Commit 7708992 ("xen/blkback: Seperate the bio allocation and the bio
submission") consolidated the pendcnt updates to just a single write,
neglecting the fact that the error path relied on it getting set to 1
up front (such that the decrement in __end_block_io_op() would actually
drop the count to zero, triggering the necessary cleanup actions).

Also remove a misleading and a stale (after said commit) comment.

Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/blkback: correctly respond to unknown, non-native requests

commit 0e367ae46503cfe7791460c8ba8434a5d60b2bd5 upstream.

If the frontend is using a non-native protocol (e.g., a 64-bit
frontend with a 32-bit backend) and it sent an unrecognized request,
the request was not translated and the response would have the
incorrect ID.  This may cause the frontend driver to behave
incorrectly or crash.

Since the ID field in the request is always in the same place,
regardless of the request type we can get the correct ID and make a
valid response (which will report BLKIF_RSP_EOPNOTSUPP).

This bug affected 64-bit SLES 11 guests when using a 32-bit backend.
This guest does a BLKIF_OP_RESERVED_1 (BLKIF_OP_PACKET in the SLES
source) and would crash in blkif_int() as the ID in the response would
be invalid.

Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iommu/amd: Make sure dma_ops are set for hotplug devices

commit c2a2876e863356b092967ea62bebdb4dd663af80 upstream.

There is a bug introduced with commit 27c2127 that causes
devices which are hot unplugged and then hot-replugged to
not have per-device dma_ops set. This causes these devices
to not function correctly. Fixed with this patch.

Reported-by: Andreas Degert <andreas.degert@googlemail.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tg3: fix length overflow in VPD firmware parsing

commit 715230a44310a8cf66fbfb5a46f9a62a9b2de424 upstream.

Commit 184b89044fb6e2a74611dafa69b1dce0d98612c6 ("tg3: Use VPD fw version
when present") introduced VPD parsing that contained a potential length
overflow.

Limit the hardware's reported firmware string length (max 255 bytes) to
stay inside the driver's firmware string length (32 bytes). On overflow,
truncate the formatted firmware string instead of potentially overwriting
portions of the tg3 struct.

http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf

Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Oded Horovitz <oded@privatecore.com>
Reported-by: Brad Spengler <spender@grsecurity.net>
Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: N-PHY: use more bits for offset in RSSI calibration

commit 2e1253d640eb7f8707d2591c93097c1e9f9c71d5 upstream.

When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.

This code was introduced in e0c9a0219a8f542e3946fe972a68aacf8c3f906c
and caused stability regression on some cards, for ex. BCM4322.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

b43: A fix for DMA transmission sequence errors

commit b251412db99ccd4495ce372fec7daee27bf06923 upstream.

Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.

This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.

Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.

Tested-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

b43: N-PHY: increase initial value of "mind" in RSSI calibration

commit e67dd874e60529dbd2e8232babb1e23479ba2ffa upstream.

We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.

This fixes a regression introduced in 3.4 by commit:
e0c9a0219a8f542e3946fe972a68aacf8c3f906c
(my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s)

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: usb: add missing freeing of skbuff

commit 36ef0b473fbf43d5db23eea4616cc1d18cec245f upstream.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

HID: usbhid: quirk for Realtek Multi-card reader

commit 3d464d9b71ef2f2b40a4bc9dcf06794fd1be9d12 upstream.

This device needs to be added to the quirks list with HID_QUIRK_NO_INIT_REPORTS,
otherwise it causes 10 seconds timeout during report initialization.

This fixes Red Hat bugzilla https://bugzilla.redhat.com/show_bug.cgi?id=806587

Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ath9k_hw: revert chainmask to user configuration after calibration

commit 74632d11a133b5baf6b9d622dd19d2f944d93d94 upstream.

The commit 'ath9k_hw: fix calibration issues on chainmask that don't
include chain 0' changed the hardware chainmask to the chip chainmask
for the duration of the calibration, but the revert to user
configuration in the reset path runs too early.

That causes some issues with limiting the number of antennas (including
spurious failure in hardware-generated packets).

Fix this by reverting the chainmask after the essential parts of the
calibration that need the workaround, and before NF calibration is run.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Tested-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

can: sja1000: fix define conflict on SH

commit f901b6bc404b67d96eca739857c097e022727b71 upstream.

Thias patch fixes a define conflict between the SH architecture and the sja1000
driver:

    drivers/net/can/sja1000/sja1000.h:59:0: warning:
        "REG_SR" redefined [enabled by default]
    arch/sh/include/asm/ptrace_32.h:25:0: note:
         this is the location of the previous definition

A SJA1000_ prefix is added to the offending sja1000 define only, to make a
minimal patch suited for stable. A later patch will add a SJA1000_ prefix to
all defines in sja1000.h.

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sysfs: handle failure path correctly for readdir()

commit e5110f411d2ee35bf8d202ccca2e89c633060dca upstream.

In case of 'if (filp->f_pos ==  0 or 1)' of sysfs_readdir(),
the failure from filldir() isn't handled, and the reference counter
of the sysfs_dirent object pointed by filp->private_data will be
released without clearing filp->private_data, so use after free
bug will be triggered later.

This patch returns immeadiately under the situation for fixing the bug,
and it is reasonable to return from readdir() when filldir() fails.

Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sysfs: fix race between readdir and lseek

commit 991f76f837bf22c5bb07261cfd86525a0a96650c upstream.

While readdir() is running, lseek() may set filp->f_pos as zero,
then may leave filp->private_data pointing to one sysfs_dirent
object without holding its reference counter, so the sysfs_dirent
object may be used after free in next readdir().

This patch holds inode->i_mutex to avoid the problem since
the lock is always held in readdir path.

Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

staging: comedi: s626: fix continuous acquisition

commit e4317ce877a31dbb9d96375391c1c4ad2210d637 upstream.

For the s626 driver, there is a bug in the handling of asynchronous
commands on the AI subdevice when the stop source is `TRIG_NONE`.  The
command should run continuously until cancelled, but the interrupt
handler stops the command running after the first scan.

The command set-up function `s626_ai_cmd()` contains this code:

switch (cmd->stop_src) {
case TRIG_COUNT:
/*  data arrives as one packet */
devpriv->ai_sample_count = cmd->stop_arg;
devpriv->ai_continous = 0;
break;
case TRIG_NONE:
/*  continous acquisition */
devpriv->ai_continous = 1;
devpriv->ai_sample_count = 0;
break;
}

The interrupt handler `s626_irq_handler()` contains this code:

if (!(devpriv->ai_continous))
devpriv->ai_sample_count--;
if (devpriv->ai_sample_count <= 0) {
devpriv->ai_cmd_running = 0;
/* ... */
}

So `devpriv->ai_sample_count` is only decremented for the `TRIG_COUNT`
case, but `devpriv->ai_cmd_running` is set to 0 (and the command
stopped) regardless.

Fix this in `s626_ai_cmd()` by setting `devpriv->ai_sample_count = 1`
for the `TRIG_NONE` case.  The interrupt handler will not decrement it
so it will remain greater than 0 and the check for stopping the
acquisition will fail.

Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Add support for Dell[QCA 0cf3:817a]

commit ebaf5795ef57a70a042ea259448a465024e2821d upstream.

Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=08 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=817a Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Add support for Dell[QCA 0cf3:0036]

commit d66629c1325399cf080ba8b2fb086c10e5439cdd upstream.

Add support for the AR9462 chip

T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=0036 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

Signed-off-by: Ming Lei <ming.lei@canonical.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Fix not closing SCO sockets in the BT_CONNECT2 state

commit eb20ff9c91ddcb2d55c1849a87d3db85af5e88a9 upstream.

With deferred setup for SCO, it is possible that userspace closes the
socket when it is in the BT_CONNECT2 state, after the Connect Request is
received but before the Accept Synchonous Connection is sent.

If this happens the following crash was observed, when the connection is
terminated:

[  +0.000003] hci_sync_conn_complete_evt: hci0 status 0x10
[  +0.000005] sco_connect_cfm: hcon ffff88003d1bd800 bdaddr 40:98:4e:32:d7:39 status 16
[  +0.000003] sco_conn_del: hcon ffff88003d1bd800 conn ffff88003cc8e300, err 110
[  +0.000015] BUG: unable to handle kernel NULL pointer dereference at 0000000000000199
[  +0.000906] IP: [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[  +0.000000] PGD 3d21f067 PUD 3d291067 PMD 0
[  +0.000000] Oops: 0002 [#1] SMP
[  +0.000000] Modules linked in: rfcomm bnep btusb bluetooth
[  +0.000000] CPU 0
[  +0.000000] Pid: 1481, comm: kworker/u:2H Not tainted 3.9.0-rc1-25019-gad82cdd #1 Bochs Bochs
[  +0.000000] RIP: 0010:[<ffffffff810620dd>]  [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[  +0.000000] RSP: 0018:ffff88003c3c19d8  EFLAGS: 00010002
[  +0.000000] RAX: 0000000000000001 RBX: 0000000000000246 RCX: 0000000000000000
[  +0.000000] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff88003d1be868
[  +0.000000] RBP: ffff88003c3c1a98 R08: 0000000000000002 R09: 0000000000000000
[  +0.000000] R10: ffff88003d1be868 R11: ffff88003e20b000 R12: 0000000000000002
[  +0.000000] R13: ffff88003aaa8000 R14: 000000000000006e R15: ffff88003d1be850
[  +0.000000] FS:  0000000000000000(0000) GS:ffff88003e200000(0000) knlGS:0000000000000000
[  +0.000000] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[  +0.000000] CR2: 0000000000000199 CR3: 000000003c1cb000 CR4: 00000000000006b0
[  +0.000000] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  +0.000000] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[  +0.000000] Process kworker/u:2H (pid: 1481, threadinfo ffff88003c3c0000, task ffff88003aaa8000)
[  +0.000000] Stack:
[  +0.000000]  ffffffff81b16342 0000000000000000 0000000000000000 ffff88003d1be868
[  +0.000000]  ffffffff00000000 00018c0c7863e367 000000003c3c1a28 ffffffff8101efbd
[  +0.000000]  0000000000000000 ffff88003e3d2400 ffff88003c3c1a38 ffffffff81007c7a
[  +0.000000] Call Trace:
[  +0.000000]  [<ffffffff8101efbd>] ? kvm_clock_read+0x34/0x3b
[  +0.000000]  [<ffffffff81007c7a>] ? paravirt_sched_clock+0x9/0xd
[  +0.000000]  [<ffffffff81007fd4>] ? sched_clock+0x9/0xb
[  +0.000000]  [<ffffffff8104fd7a>] ? sched_clock_local+0x12/0x75
[  +0.000000]  [<ffffffff810632d1>] lock_acquire+0x93/0xb1
[  +0.000000]  [<ffffffffa0022339>] ? spin_lock+0x9/0xb [bluetooth]
[  +0.000000]  [<ffffffff8105f3d8>] ? lock_release_holdtime.part.22+0x4e/0x55
[  +0.000000]  [<ffffffff814f6038>] _raw_spin_lock+0x40/0x74
[  +0.000000]  [<ffffffffa0022339>] ? spin_lock+0x9/0xb [bluetooth]
[  +0.000000]  [<ffffffff814f6936>] ? _raw_spin_unlock+0x23/0x36
[  +0.000000]  [<ffffffffa0022339>] spin_lock+0x9/0xb [bluetooth]
[  +0.000000]  [<ffffffffa00230cc>] sco_conn_del+0x76/0xbb [bluetooth]
[  +0.000000]  [<ffffffffa002391d>] sco_connect_cfm+0x2da/0x2e9 [bluetooth]
[  +0.000000]  [<ffffffffa000862a>] hci_proto_connect_cfm+0x38/0x65 [bluetooth]
[  +0.000000]  [<ffffffffa0008d30>] hci_sync_conn_complete_evt.isra.79+0x11a/0x13e [bluetooth]
[  +0.000000]  [<ffffffffa000cd96>] hci_event_packet+0x153b/0x239d [bluetooth]
[  +0.000000]  [<ffffffff814f68ff>] ? _raw_spin_unlock_irqrestore+0x48/0x5c
[  +0.000000]  [<ffffffffa00025f6>] hci_rx_work+0xf3/0x2e3 [bluetooth]
[  +0.000000]  [<ffffffff8103efed>] process_one_work+0x1dc/0x30b
[  +0.000000]  [<ffffffff8103ef83>] ? process_one_work+0x172/0x30b
[  +0.000000]  [<ffffffff8103e07f>] ? spin_lock_irq+0x9/0xb
[  +0.000000]  [<ffffffff8103fc8d>] worker_thread+0x123/0x1d2
[  +0.000000]  [<ffffffff8103fb6a>] ? manage_workers+0x240/0x240
[  +0.000000]  [<ffffffff81044211>] kthread+0x9d/0xa5
[  +0.000000]  [<ffffffff81044174>] ? __kthread_parkme+0x60/0x60
[  +0.000000]  [<ffffffff814f75bc>] ret_from_fork+0x7c/0xb0
[  +0.000000]  [<ffffffff81044174>] ? __kthread_parkme+0x60/0x60
[  +0.000000] Code: d7 44 89 8d 50 ff ff ff 4c 89 95 58 ff ff ff e8 44 fc ff ff 44 8b 8d 50 ff ff ff 48 85 c0 4c 8b 95 58 ff ff ff 0f 84 7a 04 00 00 <f0> ff 80 98 01 00 00 83 3d 25 41 a7 00 00 45 8b b5 e8 05 00 00
[  +0.000000] RIP  [<ffffffff810620dd>] __lock_acquire+0xed/0xe82
[  +0.000000]  RSP <ffff88003c3c19d8>
[  +0.000000] CR2: 0000000000000199
[  +0.000000] ---[ end trace e73cd3b52352dd34 ]---

Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Tested-by: Frederic Dalleau <frederic.dalleau@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tile: expect new initramfs name from hypervisor file system

commit ff7f3efb9abf986f4ecd8793a9593f7ca4d6431a upstream.

The current Tilera boot infrastructure now provides the initramfs
to Linux as a Tilera-hypervisor file named "initramfs", rather than
"initramfs.cpio.gz", as before.  (This makes it reasonable to use
other compression techniques than gzip on the file without having to
worry about the name causing confusion.)  Adapt to use the new name,
but also fall back to checking for the old name.

Cc'ing to stable so that older kernels will remain compatible with
newer Tilera boot infrastructure.

Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

SUNRPC: Add barriers to ensure read ordering in rpc_wake_up_task_queue_locked

commit 1166fde6a923c30f4351515b6a9a1efc513e7d00 upstream.

We need to be careful when testing task->tk_waitqueue in
rpc_wake_up_task_queue_locked, because it can be changed while we
are holding the queue->lock.
By adding appropriate memory barriers, we can ensure that it is safe to
test task->tk_waitqueue for equality if the RPC_TASK_QUEUED bit is set.

Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/signal.c: use __ARCH_HAS_SA_RESTORER instead of SA_RESTORER

commit 522cff142d7d2f9230839c9e1f21a4d8bcc22a4a upstream.

__ARCH_HAS_SA_RESTORER is the preferred conditional for use in 3.9 and
later kernels, per Kees.

Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: Emese Revfy <re.emese@gmail.com>
Cc: PaX Team <pageexec@freemail.hu>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Serge Hallyn <serge.hallyn@canonical.com>
Cc: Julien Tinnes <jln@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

signal: Define __ARCH_HAS_SA_RESTORER so we know whether to clear sa_restorer

Vaguely based on upstream commit 574c4866e33d 'consolidate kernel-side
struct sigaction declarations'.

flush_signal_handlers() needs to know whether sigaction::sa_restorer
is defined, not whether SA_RESTORER is defined.  Define the
__ARCH_HAS_SA_RESTORER macro to indicate this.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 3.4.38

asus-laptop: Do not call HWRS on init

commit cb7da022450cdaaebd33078b6b32fb7dd2aaf6db upstream.

Since commit 8871e99f89b7 ('asus-laptop: HRWS/HWRS typo'), module
initialisation is very slow on the Asus UL30A.  The HWRS method takes
about 12 seconds to run, and subsequent initialisation also seems to
be delayed.  Since we don't really need the result, don't bother
calling it on init.  Those who are curious can still get the result
through the 'infos' device attribute.

Update the comment about HWRS in show_infos().

Reported-by: ryan <draziw+deb@gmail.com>
References: http://bugs.debian.org/692436
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rt2x00: error in configurations with mesh support disabled

commit 6ef9e2f6d12ce9e2120916804d2ddd46b954a70b upstream.

If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.

[Backported for 3.8-stable. Removed code of simultaneous AP and mesh
mode added in 4a5fc6d 3.9-rc1.]

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

exec: use -ELOOP for max recursion depth

commit d740269867021faf4ce38a449353d2b986c34a67 upstream.

To avoid an explosion of request_module calls on a chain of abusive
scripts, fail maximum recursion with -ELOOP instead of -ENOEXEC. As soon
as maximum recursion depth is hit, the error will fail all the way back
up the chain, aborting immediately.

This also has the side-effect of stopping the user's shell from attempting
to reexecute the top-level file as a shell script. As seen in the
dash source:

        if (cmd != path_bshell && errno == ENOEXEC) {
                *argv-- = cmd;
                *argv = cmd = path_bshell;
                goto repeat;
        }

The above logic was designed for running scripts automatically that lacked
the "#!" header, not to re-try failed recursion. On a legitimate -ENOEXEC,
things continue to behave as the shell expects.

Additionally, when tracking recursion, the binfmt handlers should not be
involved. The recursion being tracked is the depth of calls through
search_binary_handler(), so that function should be exclusively responsible
for tracking the depth.

Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: halfdog <me@halfdog.net>
Cc: P J P <ppandit@redhat.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

i915: initialize CADL in opregion

commit d627b62ff8d4d36761adbcd90ff143d79c94ab22 upstream.

This is rather a hack to fix brightness hotkeys on a Clevo laptop. CADL is not
used anywhere in the driver code at the moment, but it could be used in BIOS as
is the case with the Clevo laptop.

The Clevo B7130 requires the CADL field to contain at least the ID of
the LCD device. If this field is empty, the ACPI methods that are called
on pressing brightness / display switching hotkeys will not trigger a
notification. As a result, it appears as no hotkey has been pressed.

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=45452
Tested-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tools: hv: Netlink source address validation allows DoS

commit 95a69adab9acfc3981c504737a2b6578e4d846ef upstream.

The source code without this patch caused hypervkvpd to exit when it processed
a spoofed Netlink packet which has been sent from an untrusted local user.
Now Netlink messages with a non-zero nl_pid source address are ignored
and a warning is printed into the syslog.

Signed-off-by: Tomas Hozza <thozza@redhat.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udf: avoid info leak on export

commit 0143fc5e9f6f5aad4764801015bc8d4b4a278200 upstream.

For type 0x51 the udf.parent_partref member in struct fid gets copied
uninitialized to userland. Fix this by initializing it to 0.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

isofs: avoid info leak on export

commit fe685aabf7c8c9f138e5ea900954d295bf229175 upstream.

For type 1 the parent_offset member in struct isofs_fid gets copied
uninitialized to userland. Fix this by initializing it to 0.

Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

key: Fix resource leak

commit a84a921978b7d56e0e4b87ffaca6367429b4d8ff upstream.

On an error iov may still have been reallocated and need freeing

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: io_ti: fix get_icount for two port adapters

commit 5492bf3d5655b4954164f69c02955a7fca267611 upstream.

Add missing get_icount field to two-port driver.

The two-port driver was not updated when switching to the new icount
interface in commit 0bca1b913aff ("tty: Convert the USB drivers to the
new icount interface").

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: garmin_gps: fix memory leak on disconnect

commit 618aa1068df29c37a58045fe940f9106664153fd upstream.

Remove bogus disconnect test introduced by 95bef012e ("USB: more serial
drivers writing after disconnect") which prevented queued data from
being freed on disconnect.

The possible IO it was supposed to prevent is long gone.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

udf: Fix bitmap overflow on large filesystems with small block size

commit 89b1f39eb4189de745fae554b0d614d87c8d5c63 upstream.

For large UDF filesystems with 512-byte blocks the number of necessary
bitmap blocks is larger than 2^16 so s_nr_groups in udf_bitmap overflows
(the number will overflow for filesystems larger than 128 GB with
512-byte blocks). That results in ENOSPC errors despite the filesystem
has plenty of free space.

Fix the problem by changing s_nr_groups' type to 'int'. That is enough
even for filesystems 2^32 blocks (UDF maximum) and 512-byte blocksize.

Reported-and-tested-by: v10lator@myway.de
Signed-off-by: Jan Kara <jack@suse.cz>
Cc: Jim Trigg <jtrigg@spamcop.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nohz: Make tick_nohz_irq_exit() irq safe

commit e5ab012c3271990e8457055c25cafddc1ae8aa6b upstream.

As it stands, irq_exit() may or may not be called with
irqs disabled, depending on __ARCH_IRQ_EXIT_IRQS_DISABLED
that the arch can define.

It makes tick_nohz_irq_exit() unsafe. For example two
interrupts can race in tick_nohz_stop_sched_tick(): the inner
most one computes the expiring time on top of the timer list,
then it's interrupted right before reprogramming the
clock. The new interrupt enqueues a new timer list timer,
it reprogram the clock to take it into account and it exits.
The CPUs resumes the inner most interrupt and performs the clock
reprogramming without considering the new timer list timer.

This regression has been introduced by:
     280f06774afedf849f0b34248ed6aff57d0f6908
     ("nohz: Separate out irq exit and idle loop dyntick logic")

Let's fix it right now with the appropriate protections.

A saner long term solution will be to remove
__ARCH_IRQ_EXIT_IRQS_DISABLED and mandate that irq_exit() is called
with interrupts disabled.

Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linuxfoundation.org>
Link: http://lkml.kernel.org/r/1361373336-11337-1-git-send-email-fweisbec@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Lingzhu Xiang <lxiang@redhat.com>
Reviewed-by: CAI Qian <caiqian@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: fix interface refcounting

commit d7971051e4df825e0bc11b995e87bfe86355b8e5 upstream.

Make sure the interface is not released before our serial device.

Note that drivers are still not allowed to access the interface in
any way that may interfere with another driver that may have gotten
bound to the same interface after disconnect returns.

Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: cdc-acm: fix device unregistration

commit cb25505fc604292c70fc02143fc102f54c8595f0 upstream.

Unregister tty device in disconnect as is required by the USB stack.

By deferring unregistration to when the last tty reference is dropped,
the parent interface device can get unregistered before the child
resulting in broken hotplug events being generated when the tty is
finally closed:

KERNEL[2290.798128] remove   /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:3.1 (usb)
KERNEL[2290.804589] remove   /devices/pci0000:00/0000:00:1d.7/usb2/2-1 (usb)
KERNEL[2294.554799] remove   /2-1:3.1/tty/ttyACM0 (tty)

The driver must deal with tty callbacks after disconnect by checking the
disconnected flag. Specifically, further opens must be prevented and
this is already implemented.

Acked-by: Oliver Neukum <oneukum@suse.de>
Cc: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: xhci: correctly enable interrupts

commit 00eed9c814cb8f281be6f0f5d8f45025dc0a97eb upstream.

xhci has its own interrupt enabling routine, which will try to
use MSI-X/MSI if present. So the usb core shouldn't try to enable
legacy interrupts; on some machines the xhci legacy IRQ setting
is invalid.

v3: Be careful to not break XHCI_BROKEN_MSI workaround (by trenn)

Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Oliver Neukum <oneukum@suse.de>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Frederik Himpe <fhimpe@vub.ac.be>
Cc: David Haerdeman <david@hardeman.nu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: xhci - fix bit definitions for IMAN register

commit f8264340e694604863255cc0276491d17c402390 upstream.

According to XHCI specification (5.5.2.1) the IP is bit 0 and IE is bit 1
of IMAN register. Previously their definitions were reversed.

Even though there are no ill effects being observed from the swapped
definitions (because IMAN_IP is RW1C and in legacy PCI case we come in
with it already set to 1 so it was clearing itself even though we were
setting IMAN_IE instead of IMAN_IP), we should still correct the values.

This patch should be backported to kernels as old as 2.6.36, that
contain the commit 4e833c0b87a30798e67f06120cecebef6ee9644c "xhci: don't
re-enable IE constantly".

Signed-off-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86-64: Fix the failure case in copy_user_handle_tail()

commit 66db3feb486c01349f767b98ebb10b0c3d2d021b upstream.

The increment of "to" in copy_user_handle_tail() will have incremented
before a failure has been noted.  This causes us to skip a byte in the
failure case.

Only do the increment when assured there is no failure.

Signed-off-by: CQ Tang <cq.tang@intel.com>
Link: http://lkml.kernel.org/r/20130318150221.8439.993.stgit@phlsvslse11.ph.intel.com
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clockevents: Don't allow dummy broadcast timers

commit a7dc19b8652c862d5b7c4d2339bd3c428bd29c4a upstream.

Currently tick_check_broadcast_device doesn't reject clock_event_devices
with CLOCK_EVT_FEAT_DUMMY, and may select them in preference to real
hardware if they have a higher rating value. In this situation, the
dummy timer is responsible for broadcasting to itself, and the core
clockevents code may attempt to call non-existent callbacks for
programming the dummy, eventually leading to a panic.

This patch makes tick_check_broadcast_device always reject dummy timers,
preventing this problem.

Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IPoIB: Fix send lockup due to missed TX completion

commit 1ee9e2aa7b31427303466776f455d43e5e3c9275 upstream.

Commit f0dc117abdfa ("IPoIB: Fix TX queue lockup with mixed UD/CM
traffic") attempts to solve an issue where unprocessed UD send
completions can deadlock the netdev.

The patch doesn't fully resolve the issue because if more than half
the tx_outstanding's were UD and all of the destinations are RC
reachable, arming the CQ doesn't solve the issue.

This patch uses the IB_CQ_REPORT_MISSED_EVENTS on the
ib_req_notify_cq().  If the rc is above 0, the UD send cq completion
callback is called directly to re-arm the send completion timer.

This issue is seen in very large parallel filesystem deployments
and the patch has been shown to correct the issue.

Reviewed-by: Dean Luick <dean.luick@intel.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix data=journal fast mount/umount hang

commit 2b405bfa84063bfa35621d2d6879f52693c614b0 upstream.

In data=journal mode, if we unmount the file system before a
transaction has a chance to complete, when the journal inode is being
evicted, we can end up calling into jbd2_log_wait_commit() for the
last transaction, after the journalling machinery has been shut down.

Arguably we should adjust ext4_should_journal_data() to return FALSE
for the journal inode, but the only place it matters is
ext4_evict_inode(), and so to save a bit of CPU time, and to make the
patch much more obviously correct by inspection(tm), we'll fix it by
explicitly not trying to waiting for a journal commit when we are
evicting the journal inode, since it's guaranteed to never succeed in
this case.

This can be easily replicated via:

     mount -t ext4 -o data=journal /dev/vdb /vdb ; umount /vdb

------------[ cut here ]------------
WARNING: at /usr/projects/linux/ext4/fs/jbd2/journal.c:542 __jbd2_log_start_commit+0xba/0xcd()
Hardware name: Bochs
JBD2: bad log_start_commit: 3005630206 3005630206 0 0
Modules linked in:
Pid: 2909, comm: umount Not tainted 3.8.0-rc3 #1020
Call Trace:
 [<c015c0ef>] warn_slowpath_common+0x68/0x7d
 [<c02b7e7d>] ? __jbd2_log_start_commit+0xba/0xcd
 [<c015c177>] warn_slowpath_fmt+0x2b/0x2f
 [<c02b7e7d>] __jbd2_log_start_commit+0xba/0xcd
 [<c02b8075>] jbd2_log_start_commit+0x24/0x34
 [<c0279ed5>] ext4_evict_inode+0x71/0x2e3
 [<c021f0ec>] evict+0x94/0x135
 [<c021f9aa>] iput+0x10a/0x110
 [<c02b7836>] jbd2_journal_destroy+0x190/0x1ce
 [<c0175284>] ? bit_waitqueue+0x50/0x50
 [<c028d23f>] ext4_put_super+0x52/0x294
 [<c020efe3>] generic_shutdown_super+0x48/0xb4
 [<c020f071>] kill_block_super+0x22/0x60
 [<c020f3e0>] deactivate_locked_super+0x22/0x49
 [<c020f5d6>] deactivate_super+0x30/0x33
 [<c0222795>] mntput_no_expire+0x107/0x10c
 [<c02233a7>] sys_umount+0x2cf/0x2e0
 [<c02233ca>] sys_oldumount+0x12/0x14
 [<c08096b8>] syscall_call+0x7/0xb
---[ end trace 6a954cc790501c1f ]---
jbd2_log_wait_commit: error: j_commit_request=-1289337090, tid=0

Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-storage: add unusual_devs entry for Samsung YP-Z3 mp3 player

commit 29f86e66428ee083aec106cca1748dc63d98ce23 upstream.

Device stucks on filesystem writes, unless following quirk is passed:
  echo 04e8:5136:m > /sys/module/usb_storage/parameters/quirks

Add corresponding entry to unusual_devs.h

Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ext4: fix the wrong number of the allocated blocks in ext4_split_extent()

commit 3a2256702e47f68f921dfad41b1764d05c572329 upstream.

This commit fixes a wrong return value of the number of the allocated
blocks in ext4_split_extent.  When the length of blocks we want to
allocate is greater than the length of the current extent, we return a
wrong number.  Let's see what happens in the following case when we
call ext4_split_extent().

  map: [48, 72]
  ex:  [32, 64, u]

'ex' will be split into two parts:
  ex1: [32, 47, u]
  ex2: [48, 64, w]

'map->m_len' is returned from this function, and the value is 24.  But
the real length is 16.  So it should be fixed.

Meanwhile in this commit we use right length of the allocated blocks
when get_reserved_cluster_alloc in ext4_ext_handle_uninitialized_extents
is called.

Signed-off-by: Zheng Liu <wenqing.lz@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

jbd2: fix use after free in jbd2_journal_dirty_metadata()

commit ad56edad089b56300fd13bb9eeb7d0424d978239 upstream.

jbd2_journal_dirty_metadata() didn't get a reference to journal_head it
was working with. This is OK in most of the cases since the journal head
should be attached to a transaction but in rare occasions when we are
journalling data, __ext4_journalled_writepage() can race with
jbd2_journal_invalidatepage() stripping buffers from a page and thus
journal head can be freed under hands of jbd2_journal_dirty_metadata().

Fix the problem by getting own journal head reference in
jbd2_journal_dirty_metadata() (and also in jbd2_journal_set_triggers()
which can possibly have the same issue).

Reported-by: Zheng Liu <gnehzuil.liu@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cifs: ignore everything in SPNEGO blob after mechTypes

commit f853c616883a8de966873a1dab283f1369e275a1 upstream.

We've had several reports of people attempting to mount Windows 8 shares
and getting failures with a return code of -EINVAL. The default sec=
mode changed recently to sec=ntlmssp. With that, we expect and parse a
SPNEGO blob from the server in the NEGOTIATE reply.

The current decode_negTokenInit function first parses all of the
mechTypes and then tries to parse the rest of the negTokenInit reply.
The parser however currently expects a mechListMIC or nothing to follow the
mechTypes, but Windows 8 puts a mechToken field there instead to carry
some info for the new NegoEx stuff.

In practice, we don't do anything with the fields after the mechTypes
anyway so I don't see any real benefit in continuing to parse them.
This patch just has the kernel ignore the fields after the mechTypes.
We'll probably need to reinstate some of this if we ever want to support
NegoEx.

Reported-by: Jason Burgess <jason@jacknife2.dns2go.com>
Reported-by: Yan Li <elliot.li.tech@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon/benchmark: make sure bo blit copy exists before using it

commit fa8d387dc3f62062a6b4afbbb2a3438094fd8584 upstream.

Fixes a segfault on asics without a blit callback.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=62239

Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: add support for Richland APUs

commit e4d170633fde379f39a90f8a5e7eb619b5d1144d upstream.

Richland APUs are a new version of the Trinity APUs
with performance and power management improvements.

Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/radeon: add Richland pci ids

commit b75bbaa038ffc426e88ea3df6c4ae11834fc3e4f upstream.

Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

target/iscsi: Fix mutual CHAP auth on big-endian arches

commit 7ac9ad11b2a5cf77a92b58ee6b672ad2fa155eb1 upstream.

See https://bugzilla.redhat.com/show_bug.cgi?id=916290

Used a temp var since we take its address in sg_init_one.

Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/hugetlb: fix total hugetlbfs pages count when using memory overcommit accouting

commit d00285884c0892bb1310df96bce6056e9ce9b9d9 upstream.

hugetlb_total_pages is used for overcommit calculations but the current
implementation considers only the default hugetlb page size (which is
either the first defined hugepage size or the one specified by
default_hugepagesz kernel boot parameter).

If the system is configured for more than one hugepage size, which is
possible since commit a137e1cc6d6e ("hugetlbfs: per mount huge page
sizes") then the overcommit estimation done by __vm_enough_memory()
(resp.  shown by meminfo_proc_show) is not precise - there is an
impression of more available/allowed memory.  This can lead to an
unexpected ENOMEM/EFAULT resp.  SIGSEGV when memory is accounted.

Testcase:
  boot: hugepagesz=1G hugepages=1
  the default overcommit ratio is 50
  before patch:

    egrep 'CommitLimit' /proc/meminfo
    CommitLimit:     55434168 kB

  after patch:

    egrep 'CommitLimit' /proc/meminfo
    CommitLimit:     54909880 kB

[akpm@linux-foundation.org: coding-style tweak]
Signed-off-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KMS: fix EDID detailed timing frame rate

commit c19b3b0f6eed552952845e4ad908dba2113d67b4 upstream.

When KMS has parsed an EDID "detailed timing", it leaves the frame rate
zeroed.  Consecutive (debug-) output of that mode thus yields 0 for
vsync.  This simple fix also speeds up future invocations of
drm_mode_vrefresh().

While it is debatable whether this qualifies as a -stable fix I'd apply
it for consistency's sake; drm_helper_probe_single_connector_modes()
does the same thing already for all probed modes.

Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KMS: fix EDID detailed timing vsync parsing

commit 16dad1d743d31a104a849c8944e6b9eb479f6cd7 upstream.

EDID spreads some values across multiple bytes; bit-fiddling is needed
to retrieve these.  The current code to parse "detailed timings" has a
cut&paste error that results in a vsync offset of at most 15 lines
instead of 63.

See

   http://en.wikipedia.org/wiki/EDID

and in the "EDID Detailed Timing Descriptor" see bytes 10+11 show why
that needs to be a left shift.

Signed-off-by: Torsten Duwe <duwe@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: bounds check execbuffer relocation count

commit 3118a4f652c7b12c752f3222af0447008f9b2368 upstream.

It is possible to wrap the counter used to allocate the buffer for
relocation copies. This could lead to heap writing overflows.

CVE-2013-0913

v3: collapse test, improve comment
v2: move check into validate_exec_list

Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Pinkie Pie
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mwifiex: fix potential out-of-boundary access to ibss rate table

commit 5f0fabf84d7b52f979dcbafa3d3c530c60d9a92c upstream.

smatch found this error:

CHECK   drivers/net/wireless/mwifiex/join.c
  drivers/net/wireless/mwifiex/join.c:1121
  mwifiex_cmd_802_11_ad_hoc_join()
  error: testing array offset 'i' after use.

Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Fix problem that prevents reassociation

commit 9437a248e7cac427c898bdb11bd1ac6844a1ead4 upstream.

The driver was failing to clear the BSSID when a disconnect happened. That
prevented a reconnection. This problem is reported at
https://bugzilla.redhat.com/show_bug.cgi?id=789605,
https://bugzilla.redhat.com/show_bug.cgi?id=866786,
https://bugzilla.redhat.com/show_bug.cgi?id=906734, and
https://bugzilla.kernel.org/show_bug.cgi?id=46171.

Thanks to Jussi Kivilinna for making the critical observation
that led to the solution.

Reported-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Alessandro Lannocca <alessandro.lannocca@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtlwifi: rtl8192cu: Fix schedule while atomic bug splat

commit 664899786cb49cb52f620e06ac19c0be524a7cfa upstream.

When run at debug 3 or higher, rtl8192cu reports a BUG as follows:

BUG: scheduling while atomic: kworker/u:0/5281/0x00000002
INFO: lockdep is turned off.
Modules linked in: rtl8192cu rtl8192c_common rtlwifi fuse af_packet bnep bluetooth b43 mac80211 cfg80211 ipv6 snd_hda_codec_conexant kvm_amd k
vm snd_hda_intel snd_hda_codec bcma rng_core snd_pcm ssb mmc_core snd_seq snd_timer snd_seq_device snd i2c_nforce2 sr_mod pcmcia forcedeth i2c_core soundcore
 cdrom sg serio_raw k8temp hwmon joydev ac battery pcmcia_core snd_page_alloc video button wmi autofs4 ext4 mbcache jbd2 crc16 thermal processor scsi_dh_alua
 scsi_dh_hp_sw scsi_dh_rdac scsi_dh_emc scsi_dh ata_generic pata_acpi pata_amd [last unloaded: rtlwifi]
Pid: 5281, comm: kworker/u:0 Tainted: G        W    3.8.0-wl+ #119
Call Trace:
 [<ffffffff814531e7>] __schedule_bug+0x62/0x70
 [<ffffffff81459af0>] __schedule+0x730/0xa30
 [<ffffffff81326e49>] ? usb_hcd_link_urb_to_ep+0x19/0xa0
 [<ffffffff8145a0d4>] schedule+0x24/0x70
 [<ffffffff814575ec>] schedule_timeout+0x18c/0x2f0
 [<ffffffff81459ec0>] ? wait_for_common+0x40/0x180
 [<ffffffff8133f461>] ? ehci_urb_enqueue+0xf1/0xee0
 [<ffffffff810a579d>] ? trace_hardirqs_on+0xd/0x10
 [<ffffffff81459f65>] wait_for_common+0xe5/0x180
 [<ffffffff8107d1c0>] ? try_to_wake_up+0x2d0/0x2d0
 [<ffffffff8145a08e>] wait_for_completion_timeout+0xe/0x10
 [<ffffffff8132ab1c>] usb_start_wait_urb+0x8c/0x100
 [<ffffffff8132adf9>] usb_control_msg+0xd9/0x130
 [<ffffffffa057dd8d>] _usb_read_sync+0xcd/0x140 [rtlwifi]
 [<ffffffffa057de0e>] _usb_read32_sync+0xe/0x10 [rtlwifi]
 [<ffffffffa04b0555>] rtl92cu_update_hal_rate_table+0x1a5/0x1f0 [rtl8192cu]

The cause is a synchronous read from routine rtl92cu_update_hal_rate_table().
The resulting output is not critical, thus the debug statement is
deleted.

Reported-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix free of probe entry by calling call_rcu_sched()

commit 740466bc89ad8bd5afcc8de220f715f62b21e365 upstream.

Because function tracing is very invasive, and can even trace
calls to rcu_read_lock(), RCU access in function tracing is done
with preempt_disable_notrace(). This requires a synchronize_sched()
for updates and not a synchronize_rcu().

Function probes (traceon, traceoff, etc) must be freed after
a synchronize_sched() after its entry has been removed from the
hash. But call_rcu() is used. Fix this by using call_rcu_sched().

Also fix the usage to use hlist_del_rcu() instead of hlist_del().

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tracing: Fix race in snapshot swapping

commit 2721e72dd10f71a3ba90f59781becf02638aa0d9 upstream.

Although the swap is wrapped with a spin_lock, the assignment
of the temp buffer used to swap is not within that lock.
It needs to be moved into that lock, otherwise two swaps
happening on two different CPUs, can end up using the wrong
temp buffer to assign in the swap.

Luckily, all current callers of the swap function appear to have
their own locks. But in case something is added that allows two
different callers to call the swap, then there's a chance that
this race can trigger and corrupt the buffers.

New code is coming soon that will allow for this race to trigger.

I've Cc'd stable, so this bug will not show up if someone backports
one of the changes that can trigger this bug.

Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: restrict kernel address leak in debugfs

commit 2563a4524febe8f4a98e717e02436d1aaf672aa2 upstream.

Masks kernel address info-leak in object dumps with the %pK suffix,
so they cannot be used to target kernel memory corruption attacks if
the kptr_restrict sysctl is set.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: snd-usb: mixer: ignore -EINVAL in snd_usb_mixer_controls()

commit 83ea5d18d74f032a760fecde78c0210f66f7f70c upstream.

Creation of individual mixer controls may fail, but that shouldn't cause
the entire mixer creation to fail. Even worse, if the mixer creation
fails, that will error out the entire device probing.

All the functions called by parse_audio_unit() should return -EINVAL if
they find descriptors that are unsupported or believed to be malformed,
so we can safely handle this error code as a non-fatal condition in
snd_usb_mixer_controls().

That fixes a long standing bug which is commonly worked around by
adding quirks which make the driver ignore entire interfaces. Some of
them might now be unnecessary.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-and-tested-by: Rodolfo Thomazelli <pe.soberbo@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: snd-usb: mixer: propagate errors up the call chain

commit 4d7b86c98e445b075c2c4c3757eb6d3d6efbe72e upstream.

In check_input_term() and parse_audio_feature_unit(), propagate the
error value that has been returned by a failing function instead of
-EINVAL. That helps cleaning up the error pathes in the mixer.

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda - Fix typo in checking IEC958 emphasis bit

commit a686fd141e20244ad75f80ad54706da07d7bb90a upstream.

There is a typo in convert_to_spdif_status() about checking the
emphasis IEC958 status bit.  It should check the given value instead
of the resultant value.

Reported-by: Martin Weishart <martin.weishart@telosalliance.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/cirrus - Fix the digital beep registration

commit a86b1a2cd2f81f74e815e07f756edd7bc5b6f034 upstream.

The argument passed to snd_hda_attach_beep_device() is a widget NID
while spec->beep_amp holds the composed value for amp controls.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sfc: Only use TX push if a single descriptor is to be written

[ Upstream commit fae8563b25f73dc584a07bcda7a82750ff4f7672 ]

Using TX push when notifying the NIC of multiple new descriptors in
the ring will very occasionally cause the TX DMA engine to re-use an
old descriptor.  This can result in a duplicated or partly duplicated
packet (new headers with old data), or an IOMMU page fault.  This does
not happen when the pushed descriptor is the only one written.

TX push also provides little latency benefit when a packet requires
more than one descriptor.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>