Revert "scsi: aacraid: Reply queue mapping to CPUs based on IRQ affinity"

commit c5becf57dd5659c687d41d623a69f42d63f59eb2 upstream.

This reverts commit 9dc704dcc09eae7d21b5da0615eb2ed79278f63e.

Several reports have been made indicating that this commit caused
hangs. Numerous attempts at root causing and fixing the issue have
been unsuccessful so let's revert for now.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=217599
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmem: brcm_nvram: store a copy of NVRAM content

commit 1e37bf84afacd5ba17b7a13a18ca2bc78aff05c0 upstream.

This driver uses MMIO access for reading NVRAM from a flash device.
Underneath there is a flash controller that reads data and provides
mapping window.

Using MMIO interface affects controller configuration and may break real
controller driver. It was reported by multiple users of devices with
NVRAM stored on NAND.

Modify driver to read & cache NVRAM content during init and use that
copy to provide NVMEM data when requested. On NAND flashes due to their
alignment NVRAM partitions can be quite big (1 MiB and more) while
actual NVRAM content stays quite small (usually 16 to 32 KiB). To avoid
allocating so much memory check for actual data length.

Link: https://lore.kernel.org/linux-mtd/CACna6rwf3_9QVjYcM+847biTX=K0EoWXuXcSMkJO1Vy_5vmVqA@mail.gmail.com/
Fixes: 3fef9ed0627a ("nvmem: brcm_nvram: new driver exposing Broadcom's NVRAM")
Cc: <Stable@vger.kernel.org>
Cc: Arınç ÜNAL <arinc.unal@arinc9.com>
Cc: Florian Fainelli <florian.fainelli@broadcom.com>
Cc: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111358.316727-3-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: atmel: Fix clock issue when using devices with different polarities

commit fc70d643a2f6678cbe0f5c86433c1aeb4d613fcc upstream.

The current Atmel SPI controller driver (v2) behaves incorrectly when
using two SPI devices with different clock polarities and GPIO CS.

When switching from one device to another, the controller driver first
enables the CS and then applies whatever configuration suits the targeted
device (typically, the polarities). The side effect of such order is the
apparition of a spurious clock edge after enabling the CS when the clock
polarity needs to be inverted wrt. the previous configuration of the
controller.

This parasitic clock edge is problematic when the SPI device uses that edge
for internal processing, which is perfectly legitimate given that its CS
was asserted. Indeed, devices such as HVS8080 driven by driver gpio-sr in
the kernel are shift registers and will process this first clock edge to
perform a first register shift. In this case, the first bit gets lost and
the whole data block that will later be read by the kernel is all shifted
by one.

    Current behavior:
      The actual switching of the clock polarity only occurs after the CS
      when the controller sends the first message:

    CLK ------------\   /-\ /-\
                    |   | | | |    . . .
                    \---/ \-/ \
    CS  -----\
             |
             \------------------

             ^      ^   ^
             |      |   |
             |      |   Actual clock of the message sent
             |      |
             |      Change of clock polarity, which occurs with the first
             |      write to the bus. This edge occurs when the CS is
             |      already asserted, and can be interpreted as
             |      the first clock edge by the receiver.
             |
             GPIO CS toggle

This issue is specific to this controller because while the SPI core
performs the operations in the right order, the controller however does
not. In practice, the controller only applies the clock configuration right
before the first transmission.

So this is not a problem when using the controller's dedicated CS, as the
controller does things correctly, but it becomes a problem when you need to
change the clock polarity and use an external GPIO for the CS.

One possible approach to solve this problem is to send a dummy message
before actually activating the CS, so that the controller applies the clock
polarity beforehand.

New behavior:

CLK     ------\      /-\     /-\      /-\     /-\
              |      | | ... | |      | | ... | |
              \------/ \-   -/ \------/ \-   -/ \------

CS      -\/-----------------------\
         ||                       |
         \/                       \---------------------
         ^    ^       ^           ^    ^
         |    |       |           |    |
         |    |       |           |    Expected clock cycles when
         |    |       |           |    sending the message
         |    |       |           |
         |    |       |           Actual GPIO CS activation, occurs inside
         |    |       |           the driver
         |    |       |
         |    |       Dummy message, to trigger clock polarity
         |    |       reconfiguration. This message is not received and
         |    |       processed by the device because CS is low.
         |    |
         |    Change of clock polarity, forced by the dummy message. This
         |    time, the edge is not detected by the receiver.
         |
         This small spike in CS activation is due to the fact that the
         spi-core activates the CS gpio before calling the driver's
         set_cs callback, which deactivates this gpio again until the
         clock polarity is correct.

To avoid having to systematically send a dummy packet, the driver keeps
track of the clock's current polarity. In this way, it only sends the dummy
packet when necessary, ensuring that the clock will have the correct
polarity when the CS is toggled.

There could be two hardware problems with this patch:
1- Maybe the small CS activation peak can confuse SPI devices
2- If on a design, a single wire is used to select two devices depending
on its state, the dummy message may disturb them.

Fixes: 5ee36c989831 ("spi: atmel_spi update chipselect handling")
Cc: <stable@vger.kernel.org>
Signed-off-by: Louis Chauvet <louis.chauvet@bootlin.com>
Link: https://msgid.link/r/20231204154903.11607-1-louis.chauvet@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: atmel: Prevent spi transfers from being killed

commit 890188d2d7e4ac6c131ba166ca116cb315e752ee upstream.

Upstream commit e0205d6203c2 ("spi: atmel: Prevent false timeouts on
long transfers") has tried to mitigate the problem of getting spi
transfers canceled because they were lasting too long. On slow buses,
transfers in the MiB range can take more than one second and thus a
calculation was added to progressively increment the timeout value. In
order to not be too problematic from a user point of view (waiting dozen
of seconds or even minutes), the wait call was turned interruptible.

Turning the wait interruptible was a mistake as what we really wanted to
do was to be able to kill a transfer. Any signal interrupting our
transfer would not be suitable at all so a second attempt was made at
turning the wait killable instead.

Link: https://lore.kernel.org/linux-spi/20231127095842.389631-1-miquel.raynal@bootlin.com/
All being well, it was reported that JFFS2 was showing a splat when
interrupting a transfer. After some more debate about whether JFFS2
should be fixed and how, it was also pointed out that the whole
consistency of the filesystem in case of parallel I/O would be
compromised. Changing JFFS2 behavior would in theory be possible but
nobody has the energy and time and knowledge to do this now, so better
prevent spi transfers to be interrupted by the user.

Partially revert the blamed commit to no longer use the interruptible
nor the killable variant of wait_for_completion().

Fixes: e0205d6203c2 ("spi: atmel: Prevent false timeouts on long transfers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Ronald Wahl <ronald.wahl@raritan.com>
Link: https://lore.kernel.org/r/20231205083102.16946-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

spi: atmel: Do not cancel a transfer upon any signal

commit 1ca2761a7734928ffe0678f88789266cf3d05362 upstream.

The intended move from wait_for_completion_*() to
wait_for_completion_interruptible_*() was to allow (very) long spi memory
transfers to be stopped upon user request instead of freezing the
machine forever as the timeout value could now be significantly bigger.

However, depending on the user logic, applications can receive many
signals for their own "internal" purpose and have nothing to do with the
requested kernel operations, hence interrupting spi transfers upon any
signal is probably not a wise choice. Instead, let's switch to
wait_for_completion_killable_*() to only catch the "important"
signals. This was likely the intended behavior anyway.

Fixes: e0205d6203c2 ("spi: atmel: Prevent false timeouts on long transfers")
Cc: stable@vger.kernel.org
Reported-by: Ronald Wahl <ronald.wahl@raritan.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20231127095842.389631-1-miquel.raynal@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ring-buffer: Fix slowpath of interrupted event

[ Upstream commit b803d7c664d55705831729d2f2e29c874bcd62ea ]

To synchronize the timestamps with the ring buffer reservation, there are
two timestamps that are saved in the buffer meta data.

1. before_stamp
2. write_stamp

When the two are equal, the write_stamp is considered valid, as in, it may
be used to calculate the delta of the next event as the write_stamp is the
timestamp of the previous reserved event on the buffer.

This is done by the following:

 /*A*/ w = current position on the ring buffer
before = before_stamp
after = write_stamp
ts = read current timestamp

if (before != after) {
write_stamp is not valid, force adding an absolute
timestamp.
}

 /*B*/ before_stamp = ts

 /*C*/ write = local_add_return(event length, position on ring buffer)

if (w == write - event length) {
/* Nothing interrupted between A and C */
 /*E*/ write_stamp = ts;
delta = ts - after
/*
 * If nothing interrupted again,
 * before_stamp == write_stamp and write_stamp
 * can be used to calculate the delta for
 * events that come in after this one.
 */
} else {

/*
 * The slow path!
 * Was interrupted between A and C.
 */

This is the place that there's a bug. We currently have:

after = write_stamp
ts = read current timestamp

 /*F*/ if (write == current position on the ring buffer &&
    after < ts && cmpxchg(write_stamp, after, ts)) {

delta = ts - after;

} else {
delta = 0;
}

The assumption is that if the current position on the ring buffer hasn't
moved between C and F, then it also was not interrupted, and that the last
event written has a timestamp that matches the write_stamp. That is the
write_stamp is valid.

But this may not be the case:

If a task context event was interrupted by softirq between B and C.

And the softirq wrote an event that got interrupted by a hard irq between
C and E.

and the hard irq wrote an event (does not need to be interrupted)

We have:

 /*B*/ before_stamp = ts of normal context

   ---> interrupted by softirq

/*B*/ before_stamp = ts of softirq context

  ---> interrupted by hardirq

/*B*/ before_stamp = ts of hard irq context
/*E*/ write_stamp = ts of hard irq context

/* matches and write_stamp valid */
  <----

/*E*/ write_stamp = ts of softirq context

/* No longer matches before_stamp, write_stamp is not valid! */

   <---

 w != write - length, go to slow path

// Right now the order of events in the ring buffer is:
//
// |-- softirq event --|-- hard irq event --|-- normal context event --|
//

 after = write_stamp (this is the ts of softirq)
 ts = read current timestamp

 if (write == current position on the ring buffer [true] &&
     after < ts [true] && cmpxchg(write_stamp, after, ts) [true]) {

delta = ts - after  [Wrong!]

The delta is to be between the hard irq event and the normal context
event, but the above logic made the delta between the softirq event and
the normal context event, where the hard irq event is between the two. This
will shift all the remaining event timestamps on the sub-buffer
incorrectly.

The write_stamp is only valid if it matches the before_stamp. The cmpxchg
does nothing to help this.

Instead, the following logic can be done to fix this:

before = before_stamp
ts = read current timestamp
before_stamp = ts

after = write_stamp

if (write == current position on the ring buffer &&
    after == before && after < ts) {

delta = ts - after

} else {
delta = 0;
}

The above will only use the write_stamp if it still matches before_stamp
and was tested to not have changed since C.

As a bonus, with this logic we do not need any 64-bit cmpxchg() at all!

This means the 32-bit rb_time_t workaround can finally be removed. But
that's for a later time.

Link: https://lore.kernel.org/linux-trace-kernel/20231218175229.58ec3daf@gandalf.local.home/
Link: https://lore.kernel.org/linux-trace-kernel/20231218230712.3a76b081@gandalf.local.home
Cc: stable@vger.kernel.org
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: dd93942570789 ("ring-buffer: Do not try to put back write_stamp")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ring-buffer: Remove useless update to write_stamp in rb_try_to_discard()

[ Upstream commit 083e9f65bd215582bf8f6a920db729fadf16704f ]

When filtering is enabled, a temporary buffer is created to place the
content of the trace event output so that the filter logic can decide
from the trace event output if the trace event should be filtered out or
not. If it is to be filtered out, the content in the temporary buffer is
simply discarded, otherwise it is written into the trace buffer.

But if an interrupt were to come in while a previous event was using that
temporary buffer, the event written by the interrupt would actually go
into the ring buffer itself to prevent corrupting the data on the
temporary buffer. If the event is to be filtered out, the event in the
ring buffer is discarded, or if it fails to discard because another event
were to have already come in, it is turned into padding.

The update to the write_stamp in the rb_try_to_discard() happens after a
fix was made to force the next event after the discard to use an absolute
timestamp by setting the before_stamp to zero so it does not match the
write_stamp (which causes an event to use the absolute timestamp).

But there's an effort in rb_try_to_discard() to put back the write_stamp
to what it was before the event was added. But this is useless and
wasteful because nothing is going to be using that write_stamp for
calculations as it still will not match the before_stamp.

Remove this useless update, and in doing so, we remove another
cmpxchg64()!

Also update the comments to reflect this change as well as remove some
extra white space in another comment.

Link: https://lore.kernel.org/linux-trace-kernel/20231215081810.1f4f38fe@rorschach.local.home
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Joel Fernandes <joel@joelfernandes.org>
Cc: Vincent Donnefort <vdonnefort@google.com>
Fixes: b2dd797543cf ("ring-buffer: Force absolute timestamp on discard of event")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ring-buffer: Fix 32-bit rb_time_read() race with rb_time_cmpxchg()

[ Upstream commit dec890089bf79a4954b61482715ee2d084364856 ]

The following race can cause rb_time_read() to observe a corrupted time
stamp:

rb_time_cmpxchg()
[...]
        if (!rb_time_read_cmpxchg(&t->msb, msb, msb2))
                return false;
        if (!rb_time_read_cmpxchg(&t->top, top, top2))
                return false;
<interrupted before updating bottom>
__rb_time_read()
[...]
        do {
                c = local_read(&t->cnt);
                top = local_read(&t->top);
                bottom = local_read(&t->bottom);
                msb = local_read(&t->msb);
        } while (c != local_read(&t->cnt));

        *cnt = rb_time_cnt(top);

        /* If top and msb counts don't match, this interrupted a write */
        if (*cnt != rb_time_cnt(msb))
                return false;
          ^ this check fails to catch that "bottom" is still not updated.

So the old "bottom" value is returned, which is wrong.

Fix this by checking that all three of msb, top, and bottom 2-bit cnt
values match.

The reason to favor checking all three fields over requiring a specific
update order for both rb_time_set() and rb_time_cmpxchg() is because
checking all three fields is more robust to handle partial failures of
rb_time_cmpxchg() when interrupted by nested rb_time_set().

Link: https://lore.kernel.org/lkml/20231211201324.652870-1-mathieu.desnoyers@efficios.com/
Link: https://lore.kernel.org/linux-trace-kernel/20231212193049.680122-1-mathieu.desnoyers@efficios.com
Fixes: f458a1453424e ("ring-buffer: Test last update in 32bit version of __rb_time_read()")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

9p: prevent read overrun in protocol dump tracepoint

commit a931c6816078af3e306e0f444f492396ce40de31 upstream.

An out of bounds read can occur within the tracepoint 9p_protocol_dump. In
the fast assign, there is a memcpy that uses a constant size of 32 (macro
named P9_PROTO_DUMP_SZ). When the copy is invoked, the source buffer is not
guaranteed match this size.  It was found that in some cases the source
buffer size is less than 32, resulting in a read that overruns.

The size of the source buffer seems to be known at the time of the
tracepoint being invoked. The allocations happen within p9_fcall_init(),
where the capacity field is set to the allocated size of the payload
buffer. This patch tries to fix the overrun by changing the fixed array to
a dynamically sized array and using the minimum of the capacity value or
P9_PROTO_DUMP_SZ as its length. The trace log statement is adjusted to
account for this. Note that the trace log no longer splits the payload on
the first 16 bytes. The full payload is now logged to a single line.

To repro the orignal problem, operations to a plan 9 managed resource can
be used. The simplest approach might just be mounting a shared filesystem
(between host and guest vm) using the plan 9 protocol while the tracepoint
is enabled.

mount -t 9p -o trans=virtio <mount_tag> <mount_path>

The bpftrace program below can be used to show the out of bounds read.
Note that a recent version of bpftrace is needed for the raw tracepoint
support. The script was tested using v0.19.0.

/* from include/net/9p/9p.h */
struct p9_fcall {
    u32 size;
    u8 id;
    u16 tag;
    size_t offset;
    size_t capacity;
    struct kmem_cache *cache;
    u8 *sdata;
    bool zc;
};

tracepoint:9p:9p_protocol_dump
{
    /* out of bounds read can happen when this tracepoint is enabled */
}

rawtracepoint:9p_protocol_dump
{
    $pdu = (struct p9_fcall *)arg1;
    $dump_sz = (uint64)32;

    if ($dump_sz > $pdu->capacity) {
        printf("reading %zu bytes from src buffer of %zu bytes\n",
            $dump_sz, $pdu->capacity);
    }
}

Signed-off-by: JP Kobryn <inwardvessel@gmail.com>
Message-ID: <20231204202321.22730-1-inwardvessel@gmail.com>
Fixes: 60ece0833b6c ("net/9p: allocate appropriate reduced message buffers")
Cc: stable@vger.kernel.org
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915/dmc: Don't enable any pipe DMC events

commit 49e0a85ec3441edc6c77aa40206d6e5ee4597efc upstream.

The pipe DMC seems to be making a mess of things in ADL. Various weird
symptoms have been observed such as missing vblank irqs, typicalle
happening when using multiple displays.

Keep all pipe DMC event handlers disabled until needed (which is never
atm). This is also what Windows does on ADL+.

We can also drop DG2 from disable_all_flip_queue_events() since
on DG2 the pipe DMC is the one that handles the flip queue events.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8685
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211213750.27109-2-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
(cherry picked from commit 648d7be8ecf47b0556e32550145c70db153b16fb)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/i915: Reject async flips with bigjoiner

commit 88a173e5dd05e788068e8fa20a8c37c44bd8f416 upstream.

Currently async flips are busted when bigjoiner is in use.
As a short term fix simply reject async flips in that case.

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/9769
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231211081134.2698-1-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit e93bffc2ac0a833b42841f31fff955549d38ce98)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smb: client: fix OOB in smbCalcSize()

commit b35858b3786ddbb56e1c35138ba25d6adf8d0bef upstream.

Validate @smb->WordCount to avoid reading off the end of @smb and thus
causing the following KASAN splat:

  BUG: KASAN: slab-out-of-bounds in smbCalcSize+0x32/0x40 [cifs]
  Read of size 2 at addr ffff88801c024ec5 by task cifsd/1328

  CPU: 1 PID: 1328 Comm: cifsd Not tainted 6.7.0-rc5 #9
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
  rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
  Call Trace:
   <TASK>
   dump_stack_lvl+0x4a/0x80
   print_report+0xcf/0x650
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __phys_addr+0x46/0x90
   kasan_report+0xd8/0x110
   ? smbCalcSize+0x32/0x40 [cifs]
   ? smbCalcSize+0x32/0x40 [cifs]
   kasan_check_range+0x105/0x1b0
   smbCalcSize+0x32/0x40 [cifs]
   checkSMB+0x162/0x370 [cifs]
   ? __pfx_checkSMB+0x10/0x10 [cifs]
   cifs_handle_standard+0xbc/0x2f0 [cifs]
   ? srso_alias_return_thunk+0x5/0xfbef5
   cifs_demultiplex_thread+0xed1/0x1360 [cifs]
   ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs]
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? lockdep_hardirqs_on_prepare+0x136/0x210
   ? __pfx_lock_release+0x10/0x10
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? mark_held_locks+0x1a/0x90
   ? lockdep_hardirqs_on_prepare+0x136/0x210
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __kthread_parkme+0xce/0xf0
   ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs]
   kthread+0x18d/0x1d0
   ? kthread+0xdb/0x1d0
   ? __pfx_kthread+0x10/0x10
   ret_from_fork+0x34/0x60
   ? __pfx_kthread+0x10/0x10
   ret_from_fork_asm+0x1b/0x30
   </TASK>

This fixes CVE-2023-6606.

Reported-by: j51569436@gmail.com
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=218218
Cc: stable@vger.kernel.org
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smb: client: fix OOB in SMB2_query_info_init()

commit 33eae65c6f49770fec7a662935d4eb4a6406d24b upstream.

A small CIFS buffer (448 bytes) isn't big enough to hold
SMB2_QUERY_INFO request along with user's input data from
CIFS_QUERY_INFO ioctl.  That is, if the user passed an input buffer >
344 bytes, the client will memcpy() off the end of @req->Buffer in
SMB2_query_info_init() thus causing the following KASAN splat:

  BUG: KASAN: slab-out-of-bounds in SMB2_query_info_init+0x242/0x250 [cifs]
  Write of size 1023 at addr ffff88801308c5a8 by task a.out/1240

  CPU: 1 PID: 1240 Comm: a.out Not tainted 6.7.0-rc4 #5
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
  rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
  Call Trace:
   <TASK>
   dump_stack_lvl+0x4a/0x80
   print_report+0xcf/0x650
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __phys_addr+0x46/0x90
   kasan_report+0xd8/0x110
   ? SMB2_query_info_init+0x242/0x250 [cifs]
   ? SMB2_query_info_init+0x242/0x250 [cifs]
   kasan_check_range+0x105/0x1b0
   __asan_memcpy+0x3c/0x60
   SMB2_query_info_init+0x242/0x250 [cifs]
   ? __pfx_SMB2_query_info_init+0x10/0x10 [cifs]
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? smb_rqst_len+0xa6/0xc0 [cifs]
   smb2_ioctl_query_info+0x4f4/0x9a0 [cifs]
   ? __pfx_smb2_ioctl_query_info+0x10/0x10 [cifs]
   ? __pfx_cifsConvertToUTF16+0x10/0x10 [cifs]
   ? kasan_set_track+0x25/0x30
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __kasan_kmalloc+0x8f/0xa0
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? cifs_strndup_to_utf16+0x12d/0x1a0 [cifs]
   ? __build_path_from_dentry_optional_prefix+0x19d/0x2d0 [cifs]
   ? __pfx_smb2_ioctl_query_info+0x10/0x10 [cifs]
   cifs_ioctl+0x11c7/0x1de0 [cifs]
   ? __pfx_cifs_ioctl+0x10/0x10 [cifs]
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? rcu_is_watching+0x23/0x50
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __rseq_handle_notify_resume+0x6cd/0x850
   ? __pfx___schedule+0x10/0x10
   ? blkcg_iostat_update+0x250/0x290
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? ksys_write+0xe9/0x170
   __x64_sys_ioctl+0xc9/0x100
   do_syscall_64+0x47/0xf0
   entry_SYSCALL_64_after_hwframe+0x6f/0x77
  RIP: 0033:0x7f893dde49cf
  Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48
  89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <89>
  c2 3d 00 f0 ff ff 77 18 48 8b 44 24 18 64 48 2b 04 25 28 00 00
  RSP: 002b:00007ffc03ff4160 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
  RAX: ffffffffffffffda RBX: 00007ffc03ff4378 RCX: 00007f893dde49cf
  RDX: 00007ffc03ff41d0 RSI: 00000000c018cf07 RDI: 0000000000000003
  RBP: 00007ffc03ff4260 R08: 0000000000000410 R09: 0000000000000001
  R10: 00007f893dce7300 R11: 0000000000000246 R12: 0000000000000000
  R13: 00007ffc03ff4388 R14: 00007f893df15000 R15: 0000000000406de0
   </TASK>

Fix this by increasing size of SMB2_QUERY_INFO request buffers and
validating input length to prevent other callers from overflowing @req
in SMB2_query_info_init() as well.

Fixes: f5b05d622a3e ("cifs: add IOCTL for QUERY_INFO passthrough to userspace")
Cc: stable@vger.kernel.org
Reported-by: Robert Morris <rtm@csail.mit.edu>
Signed-off-by: Paulo Alcantara <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smb: client: fix potential OOB in cifs_dump_detail()

commit b50492b05fd02887b46aef079592207fb5c97a4c upstream.

Validate SMB message with ->check_message() before calling
->calc_smb_size().

Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Cc: stable@vger.kernel.org
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smb: client: fix OOB in cifsd when receiving compounded resps

commit a8f68b11158f09754418de62e6b3e7b9b7a50cc9 upstream.

Validate next header's offset in ->next_header() so that it isn't
smaller than MID_HEADER_SIZE(server) and then standard_receive3() or
->receive() ends up writing off the end of the buffer because
'pdu_length - MID_HEADER_SIZE(server)' wraps up to a huge length:

  BUG: KASAN: slab-out-of-bounds in _copy_to_iter+0x4fc/0x840
  Write of size 701 at addr ffff88800caf407f by task cifsd/1090

  CPU: 0 PID: 1090 Comm: cifsd Not tainted 6.7.0-rc4 #5
  Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS
  rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
  Call Trace:
   <TASK>
   dump_stack_lvl+0x4a/0x80
   print_report+0xcf/0x650
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __phys_addr+0x46/0x90
   kasan_report+0xd8/0x110
   ? _copy_to_iter+0x4fc/0x840
   ? _copy_to_iter+0x4fc/0x840
   kasan_check_range+0x105/0x1b0
   __asan_memcpy+0x3c/0x60
   _copy_to_iter+0x4fc/0x840
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? hlock_class+0x32/0xc0
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __pfx__copy_to_iter+0x10/0x10
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? lock_is_held_type+0x90/0x100
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __might_resched+0x278/0x360
   ? __pfx___might_resched+0x10/0x10
   ? srso_alias_return_thunk+0x5/0xfbef5
   __skb_datagram_iter+0x2c2/0x460
   ? __pfx_simple_copy_to_iter+0x10/0x10
   skb_copy_datagram_iter+0x6c/0x110
   tcp_recvmsg_locked+0x9be/0xf40
   ? __pfx_tcp_recvmsg_locked+0x10/0x10
   ? mark_held_locks+0x5d/0x90
   ? srso_alias_return_thunk+0x5/0xfbef5
   tcp_recvmsg+0xe2/0x310
   ? __pfx_tcp_recvmsg+0x10/0x10
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? lock_acquire+0x14a/0x3a0
   ? srso_alias_return_thunk+0x5/0xfbef5
   inet_recvmsg+0xd0/0x370
   ? __pfx_inet_recvmsg+0x10/0x10
   ? __pfx_lock_release+0x10/0x10
   ? do_raw_spin_trylock+0xd1/0x120
   sock_recvmsg+0x10d/0x150
   cifs_readv_from_socket+0x25a/0x490 [cifs]
   ? __pfx_cifs_readv_from_socket+0x10/0x10 [cifs]
   ? srso_alias_return_thunk+0x5/0xfbef5
   cifs_read_from_socket+0xb5/0x100 [cifs]
   ? __pfx_cifs_read_from_socket+0x10/0x10 [cifs]
   ? __pfx_lock_release+0x10/0x10
   ? do_raw_spin_trylock+0xd1/0x120
   ? _raw_spin_unlock+0x23/0x40
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __smb2_find_mid+0x126/0x230 [cifs]
   cifs_demultiplex_thread+0xd39/0x1270 [cifs]
   ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs]
   ? __pfx_lock_release+0x10/0x10
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? mark_held_locks+0x1a/0x90
   ? lockdep_hardirqs_on_prepare+0x136/0x210
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? srso_alias_return_thunk+0x5/0xfbef5
   ? __kthread_parkme+0xce/0xf0
   ? __pfx_cifs_demultiplex_thread+0x10/0x10 [cifs]
   kthread+0x18d/0x1d0
   ? kthread+0xdb/0x1d0
   ? __pfx_kthread+0x10/0x10
   ret_from_fork+0x34/0x60
   ? __pfx_kthread+0x10/0x10
   ret_from_fork_asm+0x1b/0x30
   </TASK>

Fixes: 8ce79ec359ad ("cifs: update multiplex loop to handle compounded responses")
Cc: stable@vger.kernel.org
Reported-by: Robert Morris <rtm@csail.mit.edu>
Signed-off-by: Paulo Alcantara (SUSE) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nfsd: call nfsd_last_thread() before final nfsd_put()

commit 2a501f55cd641eb4d3c16a2eab0d678693fac663 upstream.

If write_ports_addfd or write_ports_addxprt fail, they call nfsd_put()
without calling nfsd_last_thread().  This leaves nn->nfsd_serv pointing
to a structure that has been freed.

So remove 'static' from nfsd_last_thread() and call it when the
nfsd_serv is about to be destroyed.

Fixes: ec52361df99b ("SUNRPC: stop using ->sv_nrthreads as a refcount")
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dt-bindings: nvmem: mxs-ocotp: Document fsl,ocotp

commit a2a8aefecbd0f87d6127951cef33b3def8439057 upstream.

Both imx23.dtsi and imx28.dtsi describe the OCOTP nodes in
the format:

compatible = "fsl,imx28-ocotp", "fsl,ocotp";

Document the "fsl,ocotp" entry to fix the following schema
warning:

efuse@8002c000: compatible: ['fsl,imx23-ocotp', 'fsl,ocotp'] is too long
from schema $id: http://devicetree.org/schemas/nvmem/mxs-ocotp.yaml#

Fixes: 2c504460f502 ("dt-bindings: nvmem: Convert MXS OCOTP to json-schema")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20231215111358.316727-2-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: stmmac: fix incorrect flag check in timestamp interrupt

commit bd7f77dae69532ffc027ee50ff99e3792dc30b7f upstream.

The driver should continue get the timestamp if STMMAC_FLAG_EXT_SNAPSHOT_EN
flag is set.

Fixes: aa5513f5d95f ("net: stmmac: replace the ext_snapshot_en field with a flag")
Cc: <stable@vger.kernel.org> # 6.6
Signed-off-by: Song Yoong Siang <yoong.siang.song@intel.com>
Signed-off-by: Lai Peter Jun Ann <jun.ann.lai@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: avoid build bug in skb extension length calculation

commit d6e5794b06c0fab74fe6e4fa55d508a5ceb14735 upstream.

GCC seems to incorrectly fail to evaluate skb_ext_total_length() at
compile time under certain conditions.

The issue even occurs if all values in skb_ext_type_len[] are "0",
ruling out the possibility of an actual overflow.

As the patch has been in mainline since v6.6 without triggering the
problem it seems to be a very uncommon occurrence.

As the issue only occurs when -fno-tree-loop-im is specified as part of
CFLAGS_GCOV, disable the BUILD_BUG_ON() only when building with coverage
reporting enabled.

Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202312171924.4FozI5FG-lkp@intel.com/
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/lkml/487cfd35-fe68-416f-9bfd-6bb417f98304@app.fastmail.com/
Fixes: 5d21d0a65b57 ("net: generalize calculation of skb extensions length")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231218-net-skbuff-build-bug-v1-1-eefc2fb0a7d3@weissschuh.net
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: ks8851: Fix TX stall caused by TX buffer overrun

commit 3dc5d44545453de1de9c53cc529cc960a85933da upstream.

There is a bug in the ks8851 Ethernet driver that more data is written
to the hardware TX buffer than actually available. This is caused by
wrong accounting of the free TX buffer space.

The driver maintains a tx_space variable that represents the TX buffer
space that is deemed to be free. The ks8851_start_xmit_spi() function
adds an SKB to a queue if tx_space is large enough and reduces tx_space
by the amount of buffer space it will later need in the TX buffer and
then schedules a work item. If there is not enough space then the TX
queue is stopped.

The worker function ks8851_tx_work() dequeues all the SKBs and writes
the data into the hardware TX buffer. The last packet will trigger an
interrupt after it was send. Here it is assumed that all data fits into
the TX buffer.

In the interrupt routine (which runs asynchronously because it is a
threaded interrupt) tx_space is updated with the current value from the
hardware. Also the TX queue is woken up again.

Now it could happen that after data was sent to the hardware and before
handling the TX interrupt new data is queued in ks8851_start_xmit_spi()
when the TX buffer space had still some space left. When the interrupt
is actually handled tx_space is updated from the hardware but now we
already have new SKBs queued that have not been written to the hardware
TX buffer yet. Since tx_space has been overwritten by the value from the
hardware the space is not accounted for.

Now we have more data queued then buffer space available in the hardware
and ks8851_tx_work() will potentially overrun the hardware TX buffer. In
many cases it will still work because often the buffer is written out
fast enough so that no overrun occurs but for example if the peer
throttles us via flow control then an overrun may happen.

This can be fixed in different ways. The most simple way would be to set
tx_space to 0 before writing data to the hardware TX buffer preventing
the queuing of more SKBs until the TX interrupt has been handled. I have
chosen a slightly more efficient (and still rather simple) way and
track the amount of data that is already queued and not yet written to
the hardware. When new SKBs are to be queued the already queued amount
of data is honoured when checking free TX buffer space.

I tested this with a setup of two linked KS8851 running iperf3 between
the two in bidirectional mode. Before the fix I got a stall after some
minutes. With the fix I saw now issues anymore after hours.

Fixes: 3ba81f3ece3c ("net: Micrel KS8851 SPI network driver")
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org # 5.10+
Signed-off-by: Ronald Wahl <ronald.wahl@raritan.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231214181112.76052-1-rwahl@gmx.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: rfkill: gpio: set GPIO direction

commit 23484d817082c3005252d8edfc8292c8a1006b5b upstream.

Fix the undefined usage of the GPIO consumer API after retrieving the
GPIO description with GPIO_ASIS. The API documentation mentions that
GPIO_ASIS won't set a GPIO direction and requires the user to set a
direction before using the GPIO.

This can be confirmed on i.MX6 hardware, where rfkill-gpio is no longer
able to enabled/disable a device, presumably because the GPIO controller
was never configured for the output direction.

Fixes: b2f750c3a80b ("net: rfkill: gpio: prevent value glitch during probe")
Cc: stable@vger.kernel.org
Signed-off-by: Rouven Czerwinski <r.czerwinski@pengutronix.de>
Link: https://msgid.link/20231207075835.3091694-1-r.czerwinski@pengutronix.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: 9p: avoid freeing uninit memory in p9pdu_vreadf

commit ff49bf1867578f23a5ffdd38f927f6e1e16796c4 upstream.

If some of p9pdu_readf() calls inside case 'T' in p9pdu_vreadf() fails,
the error path is not handled properly. *wnames or members of *wnames
array may be left uninitialized and invalidly freed.

Initialize *wnames to NULL in beginning of case 'T'. Initialize the first
*wnames array element to NULL and nullify the failing *wnames element so
that the error path freeing loop stops on the first NULL element and
doesn't proceed further.

Found by Linux Verification Center (linuxtesting.org).

Fixes: ace51c4dd2f9 ("9p: add new protocol support code")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Message-ID: <20231206200913.16135-1-pchelkin@ispras.ru>
Cc: stable@vger.kernel.org
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Christian Schoenebeck <linux_oss@crudebyte.com>
Signed-off-by: Dominique Martinet <asmadeus@codewreck.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Input: soc_button_array - add mapping for airplane mode button

commit ea3715941a9b7d816a1e9096ac0577900af2a69e upstream.

This add a mapping for the airplane mode button on the TUXEDO Pulse Gen3.

While it is physically a key it behaves more like a switch, sending a key
down on first press and a key up on 2nd press. Therefor the switch event
is used here. Besides this behaviour it uses the HID usage-id 0xc6
(Wireless Radio Button) and not 0xc8 (Wireless Radio Slider Switch), but
since neither 0xc6 nor 0xc8 are currently implemented at all in
soc_button_array this not to standard behaviour is not put behind a quirk
for the moment.

Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Link: https://lore.kernel.org/r/20231215171718.80229-1-wse@tuxedocomputers.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: usb: ax88179_178a: avoid failed operations when device is disconnected

commit aef05e349bfd81c95adb4489639413fadbb74a83 upstream.

When the device is disconnected we get the following messages showing
failed operations:
Nov 28 20:22:11 localhost kernel: usb 2-3: USB disconnect, device number 2
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: unregister 'ax88179_178a' usb-0000:02:00.0-3, ASIX AX88179 USB 3.0 Gigabit Ethernet
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to read reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3: Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0001: -19
Nov 28 20:22:11 localhost kernel: ax88179_178a 2-3:1.0 enp2s0u3 (unregistered): Failed to write reg index 0x0002: -19

The reason is that although the device is detached, normal stop and
unbind operations are commanded from the driver. These operations are
not necessary in this situation, so avoid these logs when the device is
detached if the result of the operation is -ENODEV and if the new flag
informing about the disconnecting status is enabled.

cc:  <stable@vger.kernel.org>
Fixes: e2ca90c276e1f ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231207175007.263907-1-jtornosm@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: fotg210-hcd: delete an incorrect bounds test

commit 7fbcd195e2b8cc952e4aeaeb50867b798040314c upstream.

Here "temp" is the number of characters that we have written and "size"
is the size of the buffer.  The intent was clearly to say that if we have
written to the end of the buffer then stop.

However, for that to work the comparison should have been done on the
original "size" value instead of the "size -= temp" value.  Not only
will that not trigger when we want to, but there is a small chance that
it will trigger incorrectly before we want it to and we break from the
loop slightly earlier than intended.

This code was recently changed from using snprintf() to scnprintf().  With
snprintf() we likely would have continued looping and passed a negative
size parameter to snprintf().  This would have triggered an annoying
WARN().  Now that we have converted to scnprintf() "size" will never
drop below 1 and there is no real need for this test.  We could change
the condition to "if (temp <= 1) goto done;" but just deleting the test
is cleanest.

Fixes: 7d50195f6c50 ("usb: host: Faraday fotg210-hcd driver")
Cc: stable <stable@kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/ZXmwIwHe35wGfgzu@suswa
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb: typec: ucsi: fix gpio-based orientation detection

commit c994cb596bf7ef5928f06331c76f46e071b16f09 upstream.

Fix the recently added connector sanity check which was off by one and
prevented orientation notifications from being handled correctly for the
second port when using GPIOs to determine orientation.

Fixes: c6165ed2f425 ("usb: ucsi: glink: use the connector orientation GPIO to provide switch events")
Cc: stable <stable@kernel.org>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20231208123603.29957-1-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: Add more enc key size check

commit 04a342cc49a8522e99c9b3346371c329d841dcd2 upstream.

When we are slave role and receives l2cap conn req when encryption has
started, we should check the enc key size to avoid KNOB attack or BLUFFS
attack.
From SIG recommendation, implementations are advised to reject
service-level connections on an encrypted baseband link with key
strengths below 7 octets.
A simple and clear way to achieve this is to place the enc key size
check in hci_cc_read_enc_key_size()

The btmon log below shows the case that lacks enc key size check.

> HCI Event: Connect Request (0x04) plen 10
        Address: BB:22:33:44:55:99 (OUI BB-22-33)
        Class: 0x480104
          Major class: Computer (desktop, notebook, PDA, organizers)
          Minor class: Desktop workstation
          Capturing (Scanner, Microphone)
          Telephony (Cordless telephony, Modem, Headset)
        Link type: ACL (0x01)
< HCI Command: Accept Connection Request (0x01|0x0009) plen 7
        Address: BB:22:33:44:55:99 (OUI BB-22-33)
        Role: Peripheral (0x01)
> HCI Event: Command Status (0x0f) plen 4
      Accept Connection Request (0x01|0x0009) ncmd 2
        Status: Success (0x00)
> HCI Event: Connect Complete (0x03) plen 11
        Status: Success (0x00)
        Handle: 1
        Address: BB:22:33:44:55:99 (OUI BB-22-33)
        Link type: ACL (0x01)
        Encryption: Disabled (0x00)
...

> HCI Event: Encryption Change (0x08) plen 4
        Status: Success (0x00)
        Handle: 1 Address: BB:22:33:44:55:99 (OUI BB-22-33)
        Encryption: Enabled with E0 (0x01)
< HCI Command: Read Encryption Key Size (0x05|0x0008) plen 2
        Handle: 1 Address: BB:22:33:44:55:99 (OUI BB-22-33)
> HCI Event: Command Complete (0x0e) plen 7
      Read Encryption Key Size (0x05|0x0008) ncmd 2
        Status: Success (0x00)
        Handle: 1 Address: BB:22:33:44:55:99 (OUI BB-22-33)
        Key size: 6
// We should check the enc key size
...

> ACL Data RX: Handle 1 flags 0x02 dlen 12
      L2CAP: Connection Request (0x02) ident 3 len 4
        PSM: 25 (0x0019)
        Source CID: 64
< ACL Data TX: Handle 1 flags 0x00 dlen 16
      L2CAP: Connection Response (0x03) ident 3 len 8
        Destination CID: 64
        Source CID: 64
        Result: Connection pending (0x0001)
        Status: Authorization pending (0x0002)
> HCI Event: Number of Completed Packets (0x13) plen 5
        Num handles: 1
        Handle: 1 Address: BB:22:33:44:55:99 (OUI BB-22-33)
        Count: 1
        #35: len 16 (25 Kb/s)
        Latency: 5 msec (2-7 msec ~4 msec)
< ACL Data TX: Handle 1 flags 0x00 dlen 16
      L2CAP: Connection Response (0x03) ident 3 len 8
        Destination CID: 64
        Source CID: 64
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)

Cc: stable@vger.kernel.org
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: MGMT/SMP: Fix address type when using SMP over BREDR/LE

commit 59b047bc98084f8af2c41483e4d68a5adf2fa7f7 upstream.

If two Bluetooth devices both support BR/EDR and BLE, and also
support Secure Connections, then they only need to pair once.
The LTK generated during the LE pairing process may be converted
into a BR/EDR link key for BR/EDR transport, and conversely, a
link key generated during the BR/EDR SSP pairing process can be
converted into an LTK for LE transport. Hence, the link type of
the link key and LTK is not fixed, they can be either an LE LINK
or an ACL LINK.

Currently, in the mgmt_new_irk/ltk/crsk/link_key functions, the
link type is fixed, which could lead to incorrect address types
being reported to the application layer. Therefore, it is necessary
to add link_type/addr_type to the smp_irk/ltk/crsk and link_key,
to ensure the generation of the correct address type.

SMP over BREDR:
Before Fix:
> ACL Data RX: Handle 11 flags 0x02 dlen 12
        BR/EDR SMP: Identity Address Information (0x09) len 7
        Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
        Random address: 00:00:00:00:00:00 (Non-Resolvable)
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
        Key type: Authenticated key from P-256 (0x03)

After Fix:
> ACL Data RX: Handle 11 flags 0x02 dlen 12
      BR/EDR SMP: Identity Address Information (0x09) len 7
        Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
        Random address: 00:00:00:00:00:00 (Non-Resolvable)
        BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
        BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
        Key type: Authenticated key from P-256 (0x03)

SMP over LE:
Before Fix:
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
        Random address: 5F:5C:07:37:47:D5 (Resolvable)
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
        Key type: Authenticated key from P-256 (0x03)
@ MGMT Event: New Link Key (0x0009) plen 26
        BR/EDR Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
        Key type: Authenticated Combination key from P-256 (0x08)

After Fix:
@ MGMT Event: New Identity Resolving Key (0x0018) plen 30
        Random address: 5E:03:1C:00:38:21 (Resolvable)
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
@ MGMT Event: New Long Term Key (0x000a) plen 37
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
        Key type: Authenticated key from P-256 (0x03)
@ MGMT Event: New Link Key (0x0009) plen 26
        Store hint: Yes (0x01)
        LE Address: F8:7D:76:F2:12:F3 (OUI F8-7D-76)
        Key type: Authenticated Combination key from P-256 (0x08)

Cc: stable@vger.kernel.org
Signed-off-by: Xiao Yao <xiaoyao@rock-chips.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: L2CAP: Send reject on command corrupted request

commit 78b99eb1faa7371bf9c534690f26a71b6996622d upstream.

L2CAP/COS/CED/BI-02-C PTS test send a malformed L2CAP signaling packet
with 2 commands in it (a connection request and an unknown command) and
expect to get a connection response packet and a command reject packet.
The second is currently not sent.

Cc: stable@vger.kernel.org
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: af_bluetooth: Fix Use-After-Free in bt_sock_recvmsg

commit 2e07e8348ea454615e268222ae3fc240421be768 upstream.

This can cause a race with bt_sock_ioctl() because
bt_sock_recvmsg() gets the skb from sk->sk_receive_queue
and then frees it without holding lock_sock.
A use-after-free for a skb occurs with the following flow.
```
bt_sock_recvmsg() -> skb_recv_datagram() -> skb_free_datagram()
bt_sock_ioctl() -> skb_peek()
```
Add lock_sock to bt_sock_recvmsg() to fix this issue.

Cc: stable@vger.kernel.org
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Hyunwoo Kim <v4bel@theori.io>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Bluetooth: hci_event: Fix not checking if HCI_OP_INQUIRY has been sent

commit 99e67d46e5ff3c7c901af6009edec72d3d363be8 upstream.

Before setting HCI_INQUIRY bit check if HCI_OP_INQUIRY was really sent
otherwise the controller maybe be generating invalid events or, more
likely, it is a result of fuzzing tools attempting to test the right
behavior of the stack when unexpected events are generated.

Cc: stable@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218151
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ASoC: tas2781: check the validity of prm_no/cfg_no

commit f32c80d34249e1cfb2e647ab3c8ef38a460c787f upstream.

Add additional checks for program/config numbers to avoid loading from
invalid addresses.

If prm_no/cfg_no is negative, skip uploading program/config.

The tas2781-hda driver caused a NULL pointer dereference after loading
module, and before first runtime_suspend.

the state was:
tas_priv->cur_conf = -1;
tas_priv->tasdevice[i].cur_conf = 0;
program = &(tas_fmw->programs[-1]);

BUG: kernel NULL pointer dereference, address: 0000000000000010
Call Trace:
 <TASK>
 ? __die+0x23/0x70
 ? page_fault_oops+0x171/0x4e0
 ? vprintk_emit+0x175/0x2b0
 ? exc_page_fault+0x7f/0x180
 ? asm_exc_page_fault+0x26/0x30
 ? tasdevice_load_block_kernel+0x21/0x310 [snd_soc_tas2781_fmwlib]
 tasdevice_select_tuningprm_cfg+0x268/0x3a0 [snd_soc_tas2781_fmwlib]
 tasdevice_tuning_switch+0x69/0x710 [snd_soc_tas2781_fmwlib]
 tas2781_hda_playback_hook+0xd4/0x110 [snd_hda_scodec_tas2781_i2c]

Fixes: 915f5eadebd2 ("ASoC: tas2781: firmware lib")
CC: <stable@vger.kernel.org>
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://msgid.link/r/523780155bfdca9bc0acd39efc79ed039454818d.1702591356.git.soyer@irl.hu
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/realtek: Add quirk for ASUS ROG GV302XA

commit 02a460adfc4920d4da775fb59ab3e54036daef22 upstream.

Asus ROG Flowx13 (GV302XA) seems require same patch as others asus products

Signed-off-by: Clément Villeret <clement.villeret@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/0a27bf4b-3056-49ac-9651-ebd7f3e36328@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: hda/tas2781: select program 0, conf 0 by default

commit ec1de5c214eb5a892fdb7c450748249d5e2840f5 upstream.

Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.

In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.

Set cur_prog and cur_conf to 0 if available in the firmware.

Fixes: 5be27f1e3ec9 ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/038add0bdca1f979cc7abcce8f24cbcd3544084b.1702596646.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Quectel RM500Q R13 firmware support

commit 06f22cd6635bdae7d73566fca9879b2026a08e00 upstream.

Add support for Quectel RM500Q R13 firmware which uses Prot=40 for the
NMEA port:

T:  Bus=02 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  8 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs=  1
P:  Vendor=2c7c ProdID=0800 Rev= 4.14
S:  Manufacturer=Quectel
S:  Product=RM500Q-AE
S:  SerialNumber=xxxxxxxx
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=896mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=40 Driver=option
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=88(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS=1024 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS=1024 Ivl=0ms

Signed-off-by: Reinhard Speyerer <rspmn@arcor.de>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Foxconn T99W265 with new baseline

commit 13fde9ac23ca8c6d1ac13cc9eefe1f1ac3ee30a4 upstream.

This ID was added based on latest SDX12 code base line, and we
made some changes with previous 0489:e0db.

Test evidence as below:
T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  3 Spd=5000 MxCh= 0
D:  Ver= 3.20 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs=  2
P:  Vendor=0489 ProdID=e0da Rev=05.04
S:  Manufacturer=Qualcomm
S:  Product=Qualcomm Snapdragon X12
S:  SerialNumber=2bda65fb
C:  #Ifs= 6 Cfg#= 2 Atr=a0 MxPwr=896mA
I:  If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim
I:  If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:  If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option
I:  If#=0x3 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option
I:  If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

0&1: MBIM, 2: Modem, 3:GNSS, 4:Diag, 5:ADB

Signed-off-by: Slark Xiao <slark_xiao@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: option: add Quectel EG912Y module support

commit 6d79d9434c69bb8ffa8a631050eb0ad6b83d3e90 upstream.

Add Quectel EG912Y "DIAG, AT, MODEM"

0x6001: ECM / RNDIS + DIAG + AT + MODEM

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=2c7c ProdID=6001 Rev= 3.18
S:  Manufacturer=Android
S:  Product=Android
S:  SerialNumber=0000
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
A:  FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=06 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=06 Prot=00 Driver=cdc_ether
E:  Ad=87(I) Atr=03(Int.) MxPS=  64 Ivl=4096ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=00 Driver=cdc_ether
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0c(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0b(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=89(I) Atr=03(Int.) MxPS=  64 Ivl=4096ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=88(I) Atr=03(Int.) MxPS=  64 Ivl=4096ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms

Signed-off-by: Alper Ak <alperyasinak1@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

USB: serial: ftdi_sio: update Actisense PIDs constant names

commit 513d88a88e0203188a38f4647dd08170aebd85df upstream.

Update the constant names for unused USB PIDs (product identifiers) to
reflect the new products now using the PIDs.

Signed-off-by: Mark Glover <mark.glover@actisense.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: cfg80211: fix certs build to not depend on file order

commit 3c2a8ebe3fe66a5f77d4c164a0bea8e2ff37b455 upstream.

The file for the new certificate (Chen-Yu Tsai's) didn't
end with a comma, so depending on the file order in the
build rule, we'd end up with invalid C when concatenating
the (now two) certificates. Fix that.

Cc: stable@vger.kernel.org
Reported-by: Biju Das <biju.das.jz@bp.renesas.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes: fb768d3b13ff ("wifi: cfg80211: Add my certificate")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: cfg80211: Add my certificate

commit fb768d3b13ffa325b7e84480d488ac799c9d2cd7 upstream.

As announced [1][2], I have taken over maintainership of the
wireless-regdb project.

Add my certificate so that newer releases are valid to the kernel.
Seth's certificate should be kept around for awhile, at least until
a few new releases by me happen.

This should also be applied to stable trees so that stable kernels
can utilize newly released database binaries.

[1] https://lore.kernel.org/linux-wireless/CAGb2v657baNMPKU3QADijx7hZa=GUcSv2LEDdn6N=QQaFX8r-g@mail.gmail.com/
[2] https://lore.kernel.org/linux-wireless/ZWmRR5ul7EDfxCan@wens.tw/

Cc: stable@vger.kernel.org
Signed-off-by: Chen-Yu Tsai <wens@kernel.org>
Acked-by: Seth Forshee <sforshee@kernel.org>
Link: https://msgid.link/ZXHGsqs34qZyzZng@wens.tw
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

wifi: mt76: fix crash with WED rx support enabled

commit cd607f2cbbbec90682b2f6d6b85e1525d0f43b19 upstream.

If WED rx is enabled, rx buffers are added to a buffer pool that can be
filled from multiple page pools. Because buffers freed from rx poll are
not guaranteed to belong to the processed queue's page pool, lockless
caching must not be used in this case.

Cc: stable@vger.kernel.org
Fixes: 2f5c3c77fc9b ("wifi: mt76: switch to page_pool allocator")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231208075004.69843-1-nbd@nbd.name
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-storage: Add quirk for incorrect WP on Kingston DT Ultimate 3.0 G3

commit 772685c14743ad565bb271041ad3c262298cd6fc upstream.

This flash drive reports write protect during the first mode sense.

In the past this was not an issue as the kernel called revalidate twice,
thus asking the device for its write protect status twice, with write
protect being disabled in the second mode sense.

However, since commit 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to
avoid calling revalidate twice") that is no longer the case, thus the
device shows up read only.

[490891.289495] sd 12:0:0:0: [sdl] Write Protect is on
[490891.289497] sd 12:0:0:0: [sdl] Mode Sense: 2b 00 80 08

This does not appear to be a timing issue, as enabling the usbcore quirk
USB_QUIRK_DELAY_INIT has no effect on write protect.

Fixes: 1e029397d12f ("scsi: sd: Reorganize DIF/DIX code to avoid calling revalidate twice")
Cc: stable <stable@kernel.org>
Signed-off-by: Tasos Sahanidis <tasos@tasossah.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Link: https://lore.kernel.org/r/20231207134441.298131-1-tasos@tasossah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: Fix occasional boot hang for am3 usb

commit 9b6a51aab5f5f9f71d2fa16e8b4d530e1643dfcb upstream.

With subtle timings changes, we can now sometimes get an external abort on
non-linefetch error booting am3 devices at sysc_reset(). This is because
of a missing reset delay needed for the usb target module.

Looks like we never enabled the delay earlier for am3, although a similar
issue was seen earlier with a similar usb setup for dm814x as described in
commit ebf244148092 ("ARM: OMAP2+: Use srst_udelay for USB on dm814x").

Cc: stable@vger.kernel.org
Fixes: 0782e8572ce4 ("ARM: dts: Probe am335x musb with ti-sysc")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: usb-audio: Increase delay in MOTU M quirk

commit 48d6b91798a6694fdd6edb62799754b9d3fe0792 upstream.

Increase the quirk delay from 2 seconds to 4 seconds. This reflects a
change in the Windows driver in which the delay was increased to about
3.7 seconds. The larger delay fixes an issue where the device fails to
work unless it was powered up early during boot.

Also clarify in the quirk comment that the quirk is only applied to
older devices (USB ID 07fd:0008).

Signed-off-by: Jeremie Knuesel <knuesel@gmail.com>
Suggested-by: Alexander Tsoy <alexander@tsoy.me>
Cc: <stable@vger.kernel.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=211975
Link: https://lore.kernel.org/r/20231217112243.33409-1-knuesel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: triggered-buffer: prevent possible freeing of wrong buffer

commit bce61476dc82f114e24e9c2e11fb064781ec563c upstream.

Commit ee708e6baacd ("iio: buffer: introduce support for attaching more
IIO buffers") introduced support for multiple buffers per indio_dev but
left indio_dev->buffer for a few legacy use cases.

In the case of the triggered buffer, iio_triggered_buffer_cleanup()
still assumes that indio_dev->buffer points to the buffer allocated by
iio_triggered_buffer_setup_ext(). However, since
iio_triggered_buffer_setup_ext() now calls iio_device_attach_buffer()
to attach the buffer, indio_dev->buffer will only point to the buffer
allocated by iio_device_attach_buffer() if it the first buffer attached.

This adds a check to make sure that no other buffer has been attached
yet to ensure that indio_dev->buffer will be assigned when
iio_device_attach_buffer() is called.

As per discussion in the review thread, we may want to deal with multiple
triggers per device, but this is a fix for the issue in the meantime and
any such support would be unlikely to be suitable for a backport.

Fixes: ee708e6baacd ("iio: buffer: introduce support for attaching more IIO buffers")
Signed-off-by: David Lechner <dlechner@baylibre.com>
Acked-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231031210521.1661552-1-dlechner@baylibre.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: tmag5273: fix temperature offset

commit 3b8157ec4573e304a29b7bced627e144dbc3dfdb upstream.

The current offset has the scale already applied to it. The ABI
documentation defines the offset parameter as "offset to be added
to <type>[Y]_raw prior to scaling by <type>[Y]_scale in order to
obtain value in the <type> units as specified in <type>[Y]_raw
documentation"

The right value is obtained at 0 degrees Celsius by the formula provided
in the datasheet:

T = Tsens_t0 + (Tadc_t - Tadc_t0) / Tadc_res

where:
T = 0 degrees Celsius
Tsens_t0 (reference temperature) = 25 degrees Celsius
Tadc_t0 (16-bit format for Tsens_t0) = 17508
Tadc_res = 60.1 LSB/degree Celsius

The resulting offset is 16005.5, which has been truncated to 16005 to
provide an integer value with a precision loss smaller than the 1-LSB
measurement precision.

Fix the offset to apply its value prior to scaling.

Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Link: https://lore.kernel.org/r/9879beec-05fc-4fc6-af62-d771e238954e@wolfvision.net
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: ti_am335x_adc: Fix return value check of tiadc_request_dma()

commit 60576e84c187043cef11f11d015249e71151d35a upstream.

Fix wrong handling of a DMA request where the probing only failed
if -EPROPE_DEFER was returned. Instead, let us fail if a non -ENODEV
value is returned. This makes DMAs explicitly optional. Even if the
DMA request is unsuccessfully, the ADC can still work properly.
We do also handle the defer probe case by making use of dev_err_probe().

Fixes: f438b9da75eb ("drivers: iio: ti_am335x_adc: add dma support")
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20230925134427.214556-1-w.egorov@phytec.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: imu: adis16475: add spi_device_id table

commit ee4d79055aeea27f1b8c42233cc0c90d0a8b5355 upstream.

This prevents the warning message "SPI driver has no spi_device_id for..."
when registering the driver. More importantly, it makes sure that
module autoloading works as spi relies on spi: modaliases and not of.

While at it, move the of_device_id table to it's natural place.

Fixes: fff7352bf7a3c ("iio: imu: Add support for adis16475")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231102125258.3284830-1-nuno.sa@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: common: ms_sensors: ms_sensors_i2c: fix humidity conversion time table

commit 54cf39ec16335dadbe1ba008d8e5e98dae3e26f8 upstream.

The HTU21 offers 4 sampling frequencies: 20, 40, 70 and 120, which are
associated to an index that is used to select the right measurement
resolution and its corresponding measurement time. The current
implementation selects the measurement resolution and the temperature
measurement time properly, but it does not select the right humidity
measurement time in all cases.

In summary, the 40 and 70 humidity measurement times are swapped.

The reason for that is probably the unusual coding for the measurement
resolution. According to the datasheet, the bits [7,0] of the "user
register" are used as follows to select the bit resolution:

--------------------------------------------------
| Bit 7 | Bit 0 | RH | Temp | Trh (us) | Tt (us) |
--------------------------------------------------
|   0   |   0   | 12 |  14  |  16000   |  50000  |
--------------------------------------------------
|   0   |   1   | 8  |  12  |  3000    |  13000  |
--------------------------------------------------
|   1   |   0   | 10 |  13  |  5000    |  25000  |
--------------------------------------------------
|   1   |   1   | 11 |  11  |  8000    |  7000   |
--------------------------------------------------
*This table is available in the official datasheet, page 13/21. I have
just appended the times provided in the humidity/temperature tables,
pages 3/21, 5/21. Note that always a pair of resolutions is selected.

The sampling frequencies [20, 40, 70, 120] are assigned to a linear
index [0..3] which is then coded as follows [1]:

Index    [7,0]
--------------
idx 0     0,0
idx 1     1,0
idx 2     0,1
idx 3     1,1

That is done that way because the temperature measurements are being
used as the reference for the sampling frequency (the frequencies and
the temperature measurement times are correlated), so increasing the
index always reduces the temperature measurement time and its
resolution. Therefore, the temperature measurement time array is as
simple as [50000, 25000, 13000, 7000]

On the other hand, the humidity resolution cannot follow the same
pattern because of the way it is coded in the "user register", where
both resolutions are selected at the same time. The humidity measurement
time array is the following: [16000, 3000, 5000, 8000], which defines
the following assignments:

Index    [7,0]    Trh
-----------------------
idx 0     0,0     16000  -> right, [0,0] selects 12 bits (Trh = 16000)
idx 1     1,0     3000   -> wrong! [1,0] selects 10 bits (Trh = 5000)
idx 2     0,1     5000   -> wrong! [0,1] selects 8 bits (Trh = 3000)
idx 3     1,1     8000   -> right, [1,1] selects 11 bits (Trh = 8000)

The times have been ordered as if idx = 1 -> [0,1] and idx = 2 -> [1,0],
which is not the case for the reason explained above.

So a simple modification is required to obtain the right humidity
measurement time array, swapping the values in the positions 1 and 2.

The right table should be the following: [16000, 5000, 3000, 8000]

Fix the humidity measurement time array with the right idex/value
coding.

[1] The actual code that makes this coding and assigns it to the current
value of the "user register" is the following:
config_reg &= 0x7E;
config_reg |= ((i & 1) << 7) + ((i & 2) >> 1);

Fixes: d574a87cc311 ("Add meas-spec sensors common part")
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Link: https://lore.kernel.org/r/20231026-topic-htu21_conversion_time-v1-1-bd257dc44209@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: adc: imx93: add four channels for imx93 adc

commit 2475ecdb9b6e177b133cf26e64e8d441d37bebde upstream.

According to the spec, this ADC totally support 8 channels.
i.MX93 contain this ADC with 4 channels connected to pins in
the package. i.MX95 contain this ADC with 8 channels connected
to pins in the package.

Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Fixes: 7d02296ac8b8 ("iio: adc: add imx93 adc support")
Link: https://lore.kernel.org/r/20231116071026.611269-1-haibo.chen@nxp.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iio: kx022a: Fix acceleration value scaling

commit 92bfa4ab1b79be95c4f52d13f5386390f0a513c2 upstream.

The IIO ABI mandates acceleration values from accelerometer to be
emitted in m/s^2. The KX022A was emitting values in micro m/s^2.

Fix driver to report the correct scale values.

Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Reported-by: Jagath Jog J <jagathjog1996@gmail.com>
Fixes: 7c1d1677b322 ("iio: accel: Support Kionix/ROHM KX022A accelerometer")
Tested-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/ZTEt7NqfDHPOkm8j@dc78bmyyyyyyyyyyyyydt-3.rev.dnainternet.fi
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

scsi: ufs: core: Let the sq_lock protect sq_tail_slot access

[ Upstream commit 04c116e2bdfc3969f9819d2cebfdf678353c354c ]

When accessing sq_tail_slot without protection from sq_lock, a race
condition can cause multiple SQEs to be copied to duplicate SQE slots. This
can lead to multiple stability issues. Fix this by moving the *dest
initialization in ufshcd_send_command() back under protection from the
sq_lock.

Fixes: 3c85f087faec ("scsi: ufs: mcq: Use pointer arithmetic in ufshcd_send_command()")
Signed-off-by: Can Guo <quic_cang@quicinc.com>
Link: https://lore.kernel.org/r/1702913550-20631-1-git-send-email-quic_cang@quicinc.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: ufs: qcom: Return ufs_qcom_clk_scale_*() errors in ufs_qcom_clk_scale_notify()

[ Upstream commit 9264fd61e628ce180a168e6b90bde134dd49ec28 ]

In commit 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto
statements") the error handling was accidentally changed, resulting in the
error of ufs_qcom_clk_scale_*() calls not being returned.

This is the case I checked:

  ufs_qcom_clk_scale_notify ->
    'ufs_qcom_clk_scale_up_/down_pre_change' error ->
      return 0;

Make sure those errors are properly returned.

Fixes: 031312dbc695 ("scsi: ufs: ufs-qcom: Remove unnecessary goto statements")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: ChanWoo Lee <cw9316.lee@samsung.com>
Link: https://lore.kernel.org/r/20231215003812.29650-1-cw9316.lee@samsung.com
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

scsi: bnx2fc: Fix skb double free in bnx2fc_rcv()

[ Upstream commit 08c94d80b2da481652fb633e79cbc41e9e326a91 ]

skb_share_check() already drops the reference to the skb when returning
NULL. Using kfree_skb() in the error handling path leads to an skb double
free.

Fix this by removing the variable tmp_skb, and return directly when
skb_share_check() returns NULL.

Fixes: 01a4cc4d0cd6 ("bnx2fc: do not add shared skbs to the fcoe_rx_list")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20221114110626.526643-1-weiyongjun@huaweicloud.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: adc: meson: add separate config for axg SoC family

[ Upstream commit 59b75dcb0953813676b5030877f3f37cedaed87d ]

According to Amlogic custom kernels ADC of axg SoC family has
vref_select and requires this setting to work nominally and thus
needs a separate config.

Fixes: 90c6241860bf ("iio: adc: meson: init voltage control bits")
Signed-off-by: George Stark <gnstark@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231127235558.71995-1-gnstark@salutedevices.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Input: ipaq-micro-keys - add error handling for devm_kmemdup

[ Upstream commit 59b6a747e2d39227ac2325c5e29d6ab3bb070c2a ]

Check the return value of i2c_add_adapter. Static analysis revealed that
the function did not properly handle potential failures of
i2c_add_adapter, which could lead to partial initialization of the I2C
adapter and unstable operation.

Signed-off-by: Haoran Liu <liuhaoran14@163.com>
Link: https://lore.kernel.org/r/20231203164653.38983-1-liuhaoran14@163.com
Fixes: d7535ffa427b ("Input: driver for microcontroller keys on the iPaq h3xxx")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

interconnect: qcom: sm8250: Enable sync_state

[ Upstream commit bfc7db1cb94ad664546d70212699f8cc6c539e8c ]

Add the generic icc sync_state callback to ensure interconnect votes
are taken into account, instead of being pegged at maximum values.

Fixes: b95b668eaaa2 ("interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20231130-topic-8250icc_syncstate-v1-1-7ce78ba6e04c@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

iio: imu: inv_mpu6050: fix an error code problem in inv_mpu6050_read_raw

[ Upstream commit c3df0e29fb7788c4b3ddf37d5ed87dda2b822943 ]

inv_mpu6050_sensor_show() can return -EINVAL or IIO_VAL_INT. Return the
true value rather than only return IIO_VAL_INT.

Fixes: d5098447147c ("iio: imu: mpu6050: add calibration offset support")
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20231030020218.65728-1-suhui@nfschina.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

interconnect: Treat xlate() returning NULL node as an error

[ Upstream commit ad2ab1297d0c80899125a842bb7a078abfe1e6ce ]

Currently, if provider->xlate() or provider->xlate_extended()
"successfully" return a NULL node, then of_icc_get_from_provider() won't
consider that an error and will successfully return the NULL node. This
bypasses error handling in of_icc_get_by_index() and leads to NULL
dereferences in path_find().

This could be avoided by ensuring provider callbacks always return an
error for NULL nodes, but it's better to explicitly protect against this
in the common framework.

Fixes: 87e3031b6fbd ("interconnect: Allow endpoints translation via DT")
Signed-off-by: Mike Tipton <quic_mdtipton@quicinc.com>
Link: https://lore.kernel.org/r/20231025145829.11603-1-quic_mdtipton@quicinc.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

nvme-pci: fix sleeping function called from interrupt context

[ Upstream commit f6fe0b2d35457c10ec37acc209d19726bdc16dbd ]

the nvme_handle_cqe() interrupt handler calls nvme_complete_async_event()
but the latter may call nvme_auth_stop() which is a blocking function.
Sleeping functions can't be called in interrupt context

 BUG: sleeping function called from invalid context
 in_atomic(): 1, irqs_disabled(): 1, non_block: 0, pid: 0, name: swapper/15
  Call Trace:
     <IRQ>
      __cancel_work_timer+0x31e/0x460
      ? nvme_change_ctrl_state+0xcf/0x3c0 [nvme_core]
      ? nvme_change_ctrl_state+0xcf/0x3c0 [nvme_core]
      nvme_complete_async_event+0x365/0x480 [nvme_core]
      nvme_poll_cq+0x262/0xe50 [nvme]

Fix the bug by moving nvme_auth_stop() to fw_act_work
(executed by the nvme_wq workqueue)

Fixes: f50fff73d620 ("nvme: implement In-Band authentication")
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

gpiolib: cdev: add gpio_device locking wrapper around gpio_ioctl()

[ Upstream commit 1d656bd259edb89dc1d9938ec5c5389867088546 ]

While the GPIO cdev gpio_ioctl() call is in progress, the kernel can
call gpiochip_remove() which will set gdev->chip to NULL, after which
any subsequent access will cause a crash.

gpio_ioctl() was overlooked by the previous fix to protect syscalls
(bdbbae241a04), so add protection for that.

Fixes: bdbbae241a04 ("gpiolib: protect the GPIO device against being dropped while in use by user-space")
Fixes: d7c51b47ac11 ("gpio: userspace ABI for reading/writing GPIO lines")
Fixes: 3c0d9c635ae2 ("gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL")
Fixes: aad955842d1c ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

pinctrl: at91-pio4: use dedicated lock class for IRQ

[ Upstream commit 14694179e561b5f2f7e56a0f590e2cb49a9cc7ab ]

Trying to suspend to RAM on SAMA5D27 EVK leads to the following lockdep
warning:

 ============================================
 WARNING: possible recursive locking detected
 6.7.0-rc5-wt+ #532 Not tainted
 --------------------------------------------
 sh/92 is trying to acquire lock:
 c3cf306c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100

 but task is already holding lock:
 c3d7c46c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100

 other info that might help us debug this:
  Possible unsafe locking scenario:

        CPU0
        ----
   lock(&irq_desc_lock_class);
   lock(&irq_desc_lock_class);

  *** DEADLOCK ***

  May be due to missing lock nesting notation

 6 locks held by sh/92:
  #0: c3aa0258 (sb_writers#6){.+.+}-{0:0}, at: ksys_write+0xd8/0x178
  #1: c4c2df44 (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter+0x138/0x284
  #2: c32684a0 (kn->active){.+.+}-{0:0}, at: kernfs_fop_write_iter+0x148/0x284
  #3: c232b6d4 (system_transition_mutex){+.+.}-{3:3}, at: pm_suspend+0x13c/0x4e8
  #4: c387b088 (&dev->mutex){....}-{3:3}, at: __device_suspend+0x1e8/0x91c
  #5: c3d7c46c (&irq_desc_lock_class){-.-.}-{2:2}, at: __irq_get_desc_lock+0xe8/0x100

 stack backtrace:
 CPU: 0 PID: 92 Comm: sh Not tainted 6.7.0-rc5-wt+ #532
 Hardware name: Atmel SAMA5
  unwind_backtrace from show_stack+0x18/0x1c
  show_stack from dump_stack_lvl+0x34/0x48
  dump_stack_lvl from __lock_acquire+0x19ec/0x3a0c
  __lock_acquire from lock_acquire.part.0+0x124/0x2d0
  lock_acquire.part.0 from _raw_spin_lock_irqsave+0x5c/0x78
  _raw_spin_lock_irqsave from __irq_get_desc_lock+0xe8/0x100
  __irq_get_desc_lock from irq_set_irq_wake+0xa8/0x204
  irq_set_irq_wake from atmel_gpio_irq_set_wake+0x58/0xb4
  atmel_gpio_irq_set_wake from irq_set_irq_wake+0x100/0x204
  irq_set_irq_wake from gpio_keys_suspend+0xec/0x2b8
  gpio_keys_suspend from dpm_run_callback+0xe4/0x248
  dpm_run_callback from __device_suspend+0x234/0x91c
  __device_suspend from dpm_suspend+0x224/0x43c
  dpm_suspend from dpm_suspend_start+0x9c/0xa8
  dpm_suspend_start from suspend_devices_and_enter+0x1e0/0xa84
  suspend_devices_and_enter from pm_suspend+0x460/0x4e8
  pm_suspend from state_store+0x78/0xe4
  state_store from kernfs_fop_write_iter+0x1a0/0x284
  kernfs_fop_write_iter from vfs_write+0x38c/0x6f4
  vfs_write from ksys_write+0xd8/0x178
  ksys_write from ret_fast_syscall+0x0/0x1c
 Exception stack(0xc52b3fa8 to 0xc52b3ff0)
 3fa0:                   00000004 005a0ae8 00000001 005a0ae8 00000004 00000001
 3fc0: 00000004 005a0ae8 00000001 00000004 00000004 b6c616c0 00000020 0059d190
 3fe0: 00000004 b6c61678 aec5a041 aebf1a26

This warning is raised because pinctrl-at91-pio4 uses chained IRQ. Whenever
a wake up source configures an IRQ through irq_set_irq_wake, it will
lock the corresponding IRQ desc, and then call irq_set_irq_wake on "parent"
IRQ which will do the same on its own IRQ desc, but since those two locks
share the same class, lockdep reports this as an issue.

Fix lockdep false positive by setting a different class for parent and
children IRQ

Fixes: 776180848b57 ("pinctrl: introduce driver for Atmel PIO4 controller")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Link: https://lore.kernel.org/r/20231215-lockdep_warning-v1-1-8137b2510ed5@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

x86/xen: add CPU dependencies for 32-bit build

[ Upstream commit 93cd0597649844a0fe7989839a3202735fb3ae67 ]

Xen only supports modern CPUs even when running a 32-bit kernel, and it now
requires a kernel built for a 64 byte (or larger) cache line:

In file included from <command-line>:
In function 'xen_vcpu_setup',
    inlined from 'xen_vcpu_setup_restore' at arch/x86/xen/enlighten.c:111:3,
    inlined from 'xen_vcpu_restore' at arch/x86/xen/enlighten.c:141:3:
include/linux/compiler_types.h:435:45: error: call to '__compiletime_assert_287' declared with attribute error: BUILD_BUG_ON failed: sizeof(*vcpup) > SMP_CACHE_BYTES
arch/x86/xen/enlighten.c:166:9: note: in expansion of macro 'BUILD_BUG_ON'
  166 |         BUILD_BUG_ON(sizeof(*vcpup) > SMP_CACHE_BYTES);
      |         ^~~~~~~~~~~~

Enforce the dependency with a whitelist of CPU configurations. In normal
distro kernels, CONFIG_X86_GENERIC is enabled, and this works fine. When this
is not set, still allow Xen to be built on kernels that target a 64-bit
capable CPU.

Fixes: db2832309a82 ("x86/xen: fix percpu vcpu_info allocation")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Tested-by: Alyssa Ross <hi@alyssa.is>
Link: https://lore.kernel.org/r/20231204084722.3789473-1-arnd@kernel.org
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: aspeed: Handle the coalesced stop conditions with the start conditions.

[ Upstream commit b4cc1cbba5195a4dd497cf2f8f09e7807977d543 ]

Some masters may drive the transfers with low enough latency between
the nak/stop phase of the current command and the start/address phase
of the following command that the interrupts are coalesced by the
time we process them.
Handle the stop conditions before processing SLAVE_MATCH to fix the
complaints that sometimes occur below.

"aspeed-i2c-bus 1e78a040.i2c-bus: irq handled != irq. Expected
0x00000086, but was 0x00000084"

Fixes: f9eb91350bb2 ("i2c: aspeed: added slave support for Aspeed I2C driver")
Signed-off-by: Quan Nguyen <quan@os.amperecomputing.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/amdgpu: re-create idle bo's PTE during VM state machine reset

[ Upstream commit 4a0057afa35872a5f2e65576785844688dd9fa5e ]

Idle bo's PTE needs to be re-created when resetting VM state machine.
Set idle bo's vm_bo as moved to mark it as invalid.

Fixes: 55bf196f60df ("drm/amdgpu: reset VM when an error is detected")
Signed-off-by: ZhenGuo Yin <zhenguo.yin@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

i2c: qcom-geni: fix missing clk_disable_unprepare() and geni_se_resources_off()

[ Upstream commit 043465b66506e8c647cdd38a2db1f2ee0f369a1b ]

Add missing clk_disable_unprepare() and geni_se_resources_off() in the error
path in geni_i2c_probe().

Fixes: 14d02fbadb5d ("i2c: qcom-geni: add desc struct to prepare support for I2C Master Hub variant")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: fsl_sai: Fix channel swap issue on i.MX8MP

[ Upstream commit 8f0f01647550daf9cd8752c1656dcb0136d79ce1 ]

When flag mclk_with_tere and mclk_direction_output enabled,
The SAI transmitter or receiver will be enabled in very early
stage, that if FSL_SAI_xMR is set by previous case,
for example previous case is one channel, current case is
two channels, then current case started with wrong xMR in
the beginning, then channel swap happen.

The patch is to clear xMR in hw_free() to avoid such
channel swap issue.

Fixes: 3e4a82612998 ("ASoC: fsl_sai: MCLK bind with TX/RX enable bit")
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://msgid.link/r/1702953057-4499-1-git-send-email-shengjiu.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ASoC: hdmi-codec: fix missing report for jack initial status

[ Upstream commit 025222a9d6d25eee2ad9a1bb5a8b29b34b5ba576 ]

This fixes a problem introduced while fixing ELD reporting with no jack
set.

Most driver using the hdmi-codec will call the 'plugged_cb' callback
directly when registered to report the initial state of the HDMI connector.

With the commit mentionned, this occurs before jack is ready and the
initial report is lost for platforms actually providing a jack for HDMI.

Fix this by storing the hdmi connector status regardless of jack being set
or not and report the last status when jack gets set.

With this, the initial state is reported correctly even if it is
disconnected. This was not done initially and is also a fix.

Fixes: 15be353d55f9 ("ASoC: hdmi-codec: register hpd callback on component probe")
Reported-by: Zhengqiao Xia <xiazhengqiao@huaqin.corp-partner.google.com>
Closes: https://lore.kernel.org/alsa-devel/CADYyEwTNyY+fR9SgfDa-g6iiDwkU3MUdPVCYexs2_3wbcM8_vg@mail.gmail.com/
Cc: Hsin-Yi Wang <hsinyi@google.com>
Tested-by: Zhengqiao Xia <xiazhengqiao@huaqin.corp-partner.google.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20231218145655.134929-1-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915/mtl: Fix HDMI/DP PLL clock selection

[ Upstream commit dbcab554f777390d9bb6a808ed0cd90ee59bb44e ]

Select the HDMI specific PLL clock only for HDMI outputs.

Fixes: 62618c7f117e ("drm/i915/mtl: C20 PLL programming")
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231213220526.1828827-1-imre.deak@intel.com
(cherry picked from commit 937d02cc79c6828fef28a4d80d8d0ad2f7bf2b62)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

drm/i915/hwmon: Fix static analysis tool reported issues

[ Upstream commit 768f17fd25e4a98bf5166148629ecf6f647d5efc ]

Updated i915 hwmon with fixes for issues reported by static analysis tool.
Fixed integer overflow with upcasting.

v2:
- Added Fixes tag (Badal).
- Updated commit message as per review comments (Anshuman).

Fixes: 4c2572fe0ae7 ("drm/i915/hwmon: Expose power1_max_interval")
Reviewed-by: Badal Nilawar <badal.nilawar@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: Karthik Poosa <karthik.poosa@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231204144809.1518704-1-karthik.poosa@intel.com
(cherry picked from commit ac3420d3d428443a08b923f9118121c170192b62)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

afs: Fix use-after-free due to get/remove race in volume tree

[ Upstream commit 9a6b294ab496650e9f270123730df37030911b55 ]

When an afs_volume struct is put, its refcount is reduced to 0 before
the cell->volume_lock is taken and the volume removed from the
cell->volumes tree.

Unfortunately, this means that the lookup code can race and see a volume
with a zero ref in the tree, resulting in a use-after-free:

    refcount_t: addition on 0; use-after-free.
    WARNING: CPU: 3 PID: 130782 at lib/refcount.c:25 refcount_warn_saturate+0x7a/0xda
    ...
    RIP: 0010:refcount_warn_saturate+0x7a/0xda
    ...
    Call Trace:
     afs_get_volume+0x3d/0x55
     afs_create_volume+0x126/0x1de
     afs_validate_fc+0xfe/0x130
     afs_get_tree+0x20/0x2e5
     vfs_get_tree+0x1d/0xc9
     do_new_mount+0x13b/0x22e
     do_mount+0x5d/0x8a
     __do_sys_mount+0x100/0x12a
     do_syscall_64+0x3a/0x94
     entry_SYSCALL_64_after_hwframe+0x62/0x6a

Fix this by:

 (1) When putting, use a flag to indicate if the volume has been removed
     from the tree and skip the rb_erase if it has.

 (2) When looking up, use a conditional ref increment and if it fails
     because the refcount is 0, replace the node in the tree and set the
     removal flag.

Fixes: 20325960f875 ("afs: Reorganise volume and server trees to be rooted on the cell")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

afs: Fix overwriting of result of DNS query

[ Upstream commit a9e01ac8c5ff32669119c40dfdc9e80eb0b7d7aa ]

In afs_update_cell(), ret is the result of the DNS lookup and the errors
are to be handled by a switch - however, the value gets clobbered in
between by setting it to -ENOMEM in case afs_alloc_vlserver_list()
fails.

Fix this by moving the setting of -ENOMEM into the error handling for
OOM failure.  Further, only do it if we don't have an alternative error
to return.

Found by Linux Verification Center (linuxtesting.org) with SVACE.  Based
on a patch from Anastasia Belova [1].

Fixes: d5c32c89b208 ("afs: Fix cell DNS lookup")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Anastasia Belova <abelova@astralinux.ru>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
cc: lvc-project@linuxtesting.org
Link: https://lore.kernel.org/r/20231221085849.1463-1-abelova@astralinux.ru/
Link: https://lore.kernel.org/r/1700862.1703168632@warthog.procyon.org.uk/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

keys, dns: Allow key types (eg. DNS) to be reclaimed immediately on expiry

[ Upstream commit 39299bdd2546688d92ed9db4948f6219ca1b9542 ]

If a key has an expiration time, then when that time passes, the key is
left around for a certain amount of time before being collected (5 mins by
default) so that EKEYEXPIRED can be returned instead of ENOKEY.  This is a
problem for DNS keys because we want to redo the DNS lookup immediately at
that point.

Fix this by allowing key types to be marked such that keys of that type
don't have this extra period, but are reclaimed as soon as they expire and
turn this on for dns_resolver-type keys.  To make this easier to handle,
key->expiry is changed to be permanent if TIME64_MAX rather than 0.

Furthermore, give such new-style negative DNS results a 1s default expiry
if no other expiry time is set rather than allowing it to stick around
indefinitely.  This shouldn't be zero as ls will follow a failing stat call
immediately with a second with AT_SYMLINK_NOFOLLOW added.

Fixes: 1a4240f4764a ("DNS: Separate out CIFS DNS Resolver code")
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Wang Lei <wang840925@gmail.com>
cc: Jeff Layton <jlayton@redhat.com>
cc: Steve French <smfrench@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Jarkko Sakkinen <jarkko@kernel.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: linux-cifs@vger.kernel.org
cc: linux-nfs@vger.kernel.org
cc: ceph-devel@vger.kernel.org
cc: keyrings@vger.kernel.org
cc: netdev@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: check dev->gso_max_size in gso_features_check()

[ Upstream commit 24ab059d2ebd62fdccc43794796f6ffbabe49ebc ]

Some drivers might misbehave if TSO packets get too big.

GVE for instance uses a 16bit field in its TX descriptor,
and will do bad things if a packet is bigger than 2^16 bytes.

Linux TCP stack honors dev->gso_max_size, but there are
other ways for too big packets to reach an ndo_start_xmit()
handler : virtio_net, af_packet, GRO...

Add a generic check in gso_features_check() and fallback
to GSO when needed.

gso_max_size was added in the blamed commit.

Fixes: 82cc1a7a5687 ("[NET]: Add per-connection option to set max TSO frame size")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231219125331.4127498-1-edumazet@google.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/ipv6: Revert remove expired routes with a separated list of routes

[ Upstream commit dade3f6a1e4e35a5ae916d5e78b3229ec34c78ec ]

This reverts commit 3dec89b14d37ee635e772636dad3f09f78f1ab87.

The commit has some race conditions given how expires is managed on a
fib6_info in relation to gc start, adding the entry to the gc list and
setting the timer value leading to UAF. Revert the commit and try again
in a later release.

Fixes: 3dec89b14d37 ("net/ipv6: Remove expired routes with a separated list of routes")
Cc: Kui-Feng Lee <thinker.li@gmail.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231219030243.25687-1-dsahern@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: ethernet: mtk_wed: fix possible NULL pointer dereference in mtk_wed_wo_queue_tx_clean()

[ Upstream commit 7cb8cd4daacfea646cf8b5925ca2c66c98b18480 ]

In order to avoid a NULL pointer dereference, check entry->buf pointer before running
skb_free_frag in mtk_wed_wo_queue_tx_clean routine.

Fixes: 799684448e3e ("net: ethernet: mtk_wed: introduce wed wo support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/3c1262464d215faa8acebfc08869798c81c96f4a.1702827359.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

afs: Fix dynamic root lookup DNS check

[ Upstream commit 74cef6872ceaefb5b6c5c60641371ea28702d358 ]

In the afs dynamic root directory, the ->lookup() function does a DNS check
on the cell being asked for and if the DNS upcall reports an error it will
report an error back to userspace (typically ENOENT).

However, if a failed DNS upcall returns a new-style result, it will return
a valid result, with the status field set appropriately to indicate the
type of failure - and in that case, dns_query() doesn't return an error and
we let stat() complete with no error - which can cause confusion in
userspace as subsequent calls that trigger d_automount then fail with
ENOENT.

Fix this by checking the status result from a valid dns_query() and
returning an error if it indicates a failure.

Fixes: bbb4c4323a4d ("dns: Allow the dns resolver to retrieve a server set")
Reported-by: Markus Suvanto <markus.suvanto@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=216637
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

afs: Fix the dynamic root's d_delete to always delete unused dentries

[ Upstream commit 71f8b55bc30e82d6355e07811213d847981a32e2 ]

Fix the afs dynamic root's d_delete function to always delete unused
dentries rather than only deleting them if they're positive.  With things
as they stand upstream, negative dentries stemming from failed DNS lookups
stick around preventing retries.

Fixes: 66c7e1d319a5 ("afs: Split the dynroot stuff out and give it its own ops tables")
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Markus Suvanto <markus.suvanto@gmail.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: check vlan filter feature in vlan_vids_add_by_dev() and vlan_vids_del_by_dev()

[ Upstream commit 01a564bab4876007ce35f312e16797dfe40e4823 ]

I got the below warning trace:

WARNING: CPU: 4 PID: 4056 at net/core/dev.c:11066 unregister_netdevice_many_notify
CPU: 4 PID: 4056 Comm: ip Not tainted 6.7.0-rc4+ #15
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.15.0-1 04/01/2014
RIP: 0010:unregister_netdevice_many_notify+0x9a4/0x9b0
Call Trace:
 rtnl_dellink
 rtnetlink_rcv_msg
 netlink_rcv_skb
 netlink_unicast
 netlink_sendmsg
 __sock_sendmsg
 ____sys_sendmsg
 ___sys_sendmsg
 __sys_sendmsg
 do_syscall_64
 entry_SYSCALL_64_after_hwframe

It can be repoduced via:

    ip netns add ns1
    ip netns exec ns1 ip link add bond0 type bond mode 0
    ip netns exec ns1 ip link add bond_slave_1 type veth peer veth2
    ip netns exec ns1 ip link set bond_slave_1 master bond0
[1] ip netns exec ns1 ethtool -K bond0 rx-vlan-filter off
[2] ip netns exec ns1 ip link add link bond_slave_1 name bond_slave_1.0 type vlan id 0
[3] ip netns exec ns1 ip link add link bond0 name bond0.0 type vlan id 0
[4] ip netns exec ns1 ip link set bond_slave_1 nomaster
[5] ip netns exec ns1 ip link del veth2
    ip netns del ns1

This is all caused by command [1] turning off the rx-vlan-filter function
of bond0. The reason is the same as commit 01f4fd270870 ("bonding: Fix
incorrect deletion of ETH_P_8021AD protocol vid from slaves"). Commands
[2] [3] add the same vid to slave and master respectively, causing
command [4] to empty slave->vlan_info. The following command [5] triggers
this problem.

To fix this problem, we should add VLAN_FILTER feature checks in
vlan_vids_add_by_dev() and vlan_vids_del_by_dev() to prevent incorrect
addition or deletion of vlan_vid information.

Fixes: 348a1443cc43 ("vlan: introduce functions to do mass addition/deletion of vids by another device")
Signed-off-by: Liu Jian <liujian56@huawei.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mana: select PAGE_POOL

[ Upstream commit 340943fbff3d8faa44d2223ca04917df28786a07 ]

Mana uses PAGE_POOL API. x86_64 defconfig doesn't select it:

ld: vmlinux.o: in function `mana_create_page_pool.isra.0':
mana_en.c:(.text+0x9ae36f): undefined reference to `page_pool_create'
ld: vmlinux.o: in function `mana_get_rxfrag':
mana_en.c:(.text+0x9afed1): undefined reference to `page_pool_alloc_pages'
make[3]: *** [/home/yury/work/linux/scripts/Makefile.vmlinux:37: vmlinux] Error 1
make[2]: *** [/home/yury/work/linux/Makefile:1154: vmlinux] Error 2
make[1]: *** [/home/yury/work/linux/Makefile:234: __sub-make] Error 2
make[1]: Leaving directory '/home/yury/work/build-linux-x86_64'
make: *** [Makefile:234: __sub-make] Error 2

So we need to select it explicitly.

Signed-off-by: Yury Norov <yury.norov@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Simon Horman <horms@kernel.org> # build-tested
Fixes: ca9c54d2 ("net: mana: Add a driver for Microsoft Azure Network Adapter")
Link: https://lore.kernel.org/r/20231215203353.635379-1-yury.norov@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: Fix PF with enabled XDP going no-carrier after reset

[ Upstream commit f5728a418945ba53e2fdf38a6e5c5a2670965e85 ]

Commit 6624e780a577fc596788 ("ice: split ice_vsi_setup into smaller
functions") has refactored a bunch of code involved in PFR. In this
process, TC queue number adjustment for XDP was lost. Bring it back.

Lack of such adjustment causes interface to go into no-carrier after a
reset, if XDP program is attached, with the following message:

ice 0000:b1:00.0: Failed to set LAN Tx queue context, error: -22
ice 0000:b1:00.0 ens801f0np0: Failed to open VSI 0x0006 on switch 0x0001
ice 0000:b1:00.0: enable VSI failed, err -22, VSI index 0, type ICE_VSI_PF
ice 0000:b1:00.0: PF VSI rebuild failed: -22
ice 0000:b1:00.0: Rebuild failed, unload and reload driver

Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: alter feature support check for SRIOV and LAG

[ Upstream commit 4d50fcdc2476eef94c14c6761073af5667bb43b6 ]

Previously, the ice driver had support for using a handler for bonding
netdev events to ensure that conflicting features were not allowed to be
activated at the same time.  While this was still in place, additional
support was added to specifically support SRIOV and LAG together.  These
both utilized the netdev event handler, but the SRIOV and LAG feature was
behind a capabilities feature check to make sure the current NVM has
support.

The exclusion part of the event handler should be removed since there are
users who have custom made solutions that depend on the non-exclusion of
features.

Wrap the creation/registration and cleanup of the event handler and
associated structs in the probe flow with a feature check so that the
only systems that support the full implementation of LAG features will
initialize support.  This will leave other systems unhindered with
functionality as it existed before any LAG code was added.

Fixes: bb52f42acef6 ("ice: Add driver support for firmware changes for LAG")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ice: stop trashing VF VSI aggregator node ID information

[ Upstream commit 7d881346121a97756f34e00e6296a5d63f001f7f ]

When creating new VSIs, they are assigned into an aggregator node in the
scheduler tree. Information about which aggregator node a VSI is assigned
into is maintained by the vsi->agg_node structure. In ice_vsi_decfg(), this
information is being destroyed, by overwriting the valid flag and the
agg_id field to zero.

For VF VSIs, this breaks the aggregator node configuration replay, which
depends on this information. This results in VFs being inserted into the
default aggregator node. The resulting configuration will have unexpected
Tx bandwidth sharing behavior.

This was broken by commit 6624e780a577 ("ice: split ice_vsi_setup into
smaller functions"), which added the block to reset the agg_node data.

The vsi->agg_node structure is not managed by the scheduler code, but is
instead a wrapper around an aggregator node ID that is tracked at the VSI
layer. Its been around for a long time, and its primary purpose was for
handling VFs. The SR-IOV VF reset flow does not make use of the standard VSI
rebuild/replay logic, and uses vsi->agg_node as part of its handling to
rebuild the aggregator node configuration.

The logic for aggregator nodes stretches  back to early ice driver code from
commit b126bd6bcd67 ("ice: create scheduler aggregator node config and move
VSIs")

The logic in ice_vsi_decfg() which trashes the ice_agg_node data is clearly
wrong. It destroys information that is necessary for handling VF reset,. It
is also not the correct way to actually remove a VSI from an aggregator
node. For that, we need to implement logic in the scheduler code. Further,
non-VF VSIs properly replay their aggregator configuration using existing
scheduler replay logic.

To fix the VF replay logic, remove this broken aggregator node cleanup
logic. This is the simplest way to immediately fix this.

This ensures that VFs will have proper aggregate configuration after a
reset. This is especially important since VFs often perform resets as part
of their reconfiguration flows. Without fixing this, VFs will be placed in
the default aggregator node and Tx bandwidth will not be shared in the
expected and configured manner.

Fixes: 6624e780a577 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: phy: skip LED triggers on PHYs on SFP modules

[ Upstream commit b1dfc0f76231bbf395c59d20a2070684620d5d0f ]

Calling led_trigger_register() when attaching a PHY located on an SFP
module potentially (and practically) leads into a deadlock.
Fix this by not calling led_trigger_register() for PHYs localted on SFP
modules as such modules actually never got any LEDs.

======================================================
WARNING: possible circular locking dependency detected
6.7.0-rc4-next-20231208+ #0 Tainted: G           O
------------------------------------------------------
kworker/u8:2/43 is trying to acquire lock:
ffffffc08108c4e8 (triggers_list_lock){++++}-{3:3}, at: led_trigger_register+0x4c/0x1a8

but task is already holding lock:
ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp]

which lock already depends on the new lock.

the existing dependency chain (in reverse order) is:

-> #3 (&sfp->sm_mutex){+.+.}-{3:3}:
       __mutex_lock+0x88/0x7a0
       mutex_lock_nested+0x20/0x28
       cleanup_module+0x2ae0/0x3120 [sfp]
       sfp_register_bus+0x5c/0x9c
       sfp_register_socket+0x48/0xd4
       cleanup_module+0x271c/0x3120 [sfp]
       platform_probe+0x64/0xb8
       really_probe+0x17c/0x3c0
       __driver_probe_device+0x78/0x164
       driver_probe_device+0x3c/0xd4
       __driver_attach+0xec/0x1f0
       bus_for_each_dev+0x60/0xa0
       driver_attach+0x20/0x28
       bus_add_driver+0x108/0x208
       driver_register+0x5c/0x118
       __platform_driver_register+0x24/0x2c
       init_module+0x28/0xa7c [sfp]
       do_one_initcall+0x70/0x2ec
       do_init_module+0x54/0x1e4
       load_module+0x1b78/0x1c8c
       __do_sys_init_module+0x1bc/0x2cc
       __arm64_sys_init_module+0x18/0x20
       invoke_syscall.constprop.0+0x4c/0xdc
       do_el0_svc+0x3c/0xbc
       el0_svc+0x34/0x80
       el0t_64_sync_handler+0xf8/0x124
       el0t_64_sync+0x150/0x154

-> #2 (rtnl_mutex){+.+.}-{3:3}:
       __mutex_lock+0x88/0x7a0
       mutex_lock_nested+0x20/0x28
       rtnl_lock+0x18/0x20
       set_device_name+0x30/0x130
       netdev_trig_activate+0x13c/0x1ac
       led_trigger_set+0x118/0x234
       led_trigger_write+0x104/0x17c
       sysfs_kf_bin_write+0x64/0x80
       kernfs_fop_write_iter+0x128/0x1b4
       vfs_write+0x178/0x2a4
       ksys_write+0x58/0xd4
       __arm64_sys_write+0x18/0x20
       invoke_syscall.constprop.0+0x4c/0xdc
       do_el0_svc+0x3c/0xbc
       el0_svc+0x34/0x80
       el0t_64_sync_handler+0xf8/0x124
       el0t_64_sync+0x150/0x154

-> #1 (&led_cdev->trigger_lock){++++}-{3:3}:
       down_write+0x4c/0x13c
       led_trigger_write+0xf8/0x17c
       sysfs_kf_bin_write+0x64/0x80
       kernfs_fop_write_iter+0x128/0x1b4
       vfs_write+0x178/0x2a4
       ksys_write+0x58/0xd4
       __arm64_sys_write+0x18/0x20
       invoke_syscall.constprop.0+0x4c/0xdc
       do_el0_svc+0x3c/0xbc
       el0_svc+0x34/0x80
       el0t_64_sync_handler+0xf8/0x124
       el0t_64_sync+0x150/0x154

-> #0 (triggers_list_lock){++++}-{3:3}:
       __lock_acquire+0x12a0/0x2014
       lock_acquire+0x100/0x2ac
       down_write+0x4c/0x13c
       led_trigger_register+0x4c/0x1a8
       phy_led_triggers_register+0x9c/0x214
       phy_attach_direct+0x154/0x36c
       phylink_attach_phy+0x30/0x60
       phylink_sfp_connect_phy+0x140/0x510
       sfp_add_phy+0x34/0x50
       init_module+0x15c/0xa7c [sfp]
       cleanup_module+0x1d94/0x3120 [sfp]
       cleanup_module+0x2bb4/0x3120 [sfp]
       process_one_work+0x1f8/0x4ec
       worker_thread+0x1e8/0x3d8
       kthread+0x104/0x110
       ret_from_fork+0x10/0x20

other info that might help us debug this:

Chain exists of:
  triggers_list_lock --> rtnl_mutex --> &sfp->sm_mutex

 Possible unsafe locking scenario:

       CPU0                    CPU1
       ----                    ----
  lock(&sfp->sm_mutex);
                               lock(rtnl_mutex);
                               lock(&sfp->sm_mutex);
  lock(triggers_list_lock);

 *** DEADLOCK ***

4 locks held by kworker/u8:2/43:
 #0: ffffff80c000f938 ((wq_completion)events_power_efficient){+.+.}-{0:0}, at: process_one_work+0x150/0x4ec
 #1: ffffffc08214bde8 ((work_completion)(&(&sfp->timeout)->work)){+.+.}-{0:0}, at: process_one_work+0x150/0x4ec
 #2: ffffffc0810902f8 (rtnl_mutex){+.+.}-{3:3}, at: rtnl_lock+0x18/0x20
 #3: ffffff80c5c6f318 (&sfp->sm_mutex){+.+.}-{3:3}, at: cleanup_module+0x2ba8/0x3120 [sfp]

stack backtrace:
CPU: 0 PID: 43 Comm: kworker/u8:2 Tainted: G           O       6.7.0-rc4-next-20231208+ #0
Hardware name: Bananapi BPI-R4 (DT)
Workqueue: events_power_efficient cleanup_module [sfp]
Call trace:
 dump_backtrace+0xa8/0x10c
 show_stack+0x14/0x1c
 dump_stack_lvl+0x5c/0xa0
 dump_stack+0x14/0x1c
 print_circular_bug+0x328/0x430
 check_noncircular+0x124/0x134
 __lock_acquire+0x12a0/0x2014
 lock_acquire+0x100/0x2ac
 down_write+0x4c/0x13c
 led_trigger_register+0x4c/0x1a8
 phy_led_triggers_register+0x9c/0x214
 phy_attach_direct+0x154/0x36c
 phylink_attach_phy+0x30/0x60
 phylink_sfp_connect_phy+0x140/0x510
 sfp_add_phy+0x34/0x50
 init_module+0x15c/0xa7c [sfp]
 cleanup_module+0x1d94/0x3120 [sfp]
 cleanup_module+0x2bb4/0x3120 [sfp]
 process_one_work+0x1f8/0x4ec
 worker_thread+0x1e8/0x3d8
 kthread+0x104/0x110
 ret_from_fork+0x10/0x20

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes: 01e5b728e9e4 ("net: phy: Add a binding for PHY LEDs")
Link: https://lore.kernel.org/r/102a9dce38bdf00215735d04cd4704458273ad9c.1702339354.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

bnxt_en: do not map packet buffers twice

[ Upstream commit 23c93c3b6275a59f2a685f4a693944b53c31df4e ]

Remove double-mapping of DMA buffers as it can prevent page pool entries
from being freed.  Mapping is managed by page pool infrastructure and
was previously managed by the driver in __bnxt_alloc_rx_page before
allowing the page pool infrastructure to manage it.

Fixes: 578fcfd26e2a ("bnxt_en: Let the page pool manage the DMA mapping")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: David Wei <dw@davidwei.uk>
Link: https://lore.kernel.org/r/20231214213138.98095-1-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: hci_core: Fix hci_conn_hash_lookup_cis

[ Upstream commit 50efc63d1a7a7b9a6ed21adae1b9a7123ec8abc0 ]

hci_conn_hash_lookup_cis shall always match the requested CIG and CIS
ids even when they are unset as otherwise it result in not being able
to bind/connect different sockets to the same address as that would
result in having multiple sockets mapping to the same hci_conn which
doesn't really work and prevents BAP audio configuration such as
AC 6(i) when CIG and CIS are left unset.

Fixes: c14516faede3 ("Bluetooth: hci_conn: Fix not matching by CIS ID")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: hci_event: shut up a false-positive warning

[ Upstream commit a5812c68d849505ea657f653446512b85887f813 ]

Turning on -Wstringop-overflow globally exposed a misleading compiler
warning in bluetooth:

net/bluetooth/hci_event.c: In function 'hci_cc_read_class_of_dev':
net/bluetooth/hci_event.c:524:9: error: 'memcpy' writing 3 bytes into a
region of size 0 overflows the destination [-Werror=stringop-overflow=]
  524 |         memcpy(hdev->dev_class, rp->dev_class, 3);
      |         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

The problem here is the check for hdev being NULL in bt_dev_dbg() that
leads the compiler to conclude that hdev->dev_class might be an invalid
pointer access.

Add another explicit check for the same condition to make sure gcc sees
this cannot happen.

Fixes: a9de9248064b ("[Bluetooth] Switch from OGF+OCF to using only opcodes")
Fixes: 1b56c90018f0 ("Makefile: Enable -Wstringop-overflow globally")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Fix deadlock in vhci_send_frame

[ Upstream commit 769bf60e17ee1a56a81e7c031192c3928312c52e ]

syzbot found a potential circular dependency leading to a deadlock:
    -> #3 (&hdev->req_lock){+.+.}-{3:3}:
    __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599
    __mutex_lock kernel/locking/mutex.c:732 [inline]
    mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784
    hci_dev_do_close+0x3f/0x9f net/bluetooth/hci_core.c:551
    hci_rfkill_set_block+0x130/0x1ac net/bluetooth/hci_core.c:935
    rfkill_set_block+0x1e6/0x3b8 net/rfkill/core.c:345
    rfkill_fop_write+0x2d8/0x672 net/rfkill/core.c:1274
    vfs_write+0x277/0xcf5 fs/read_write.c:594
    ksys_write+0x19b/0x2bd fs/read_write.c:650
    do_syscall_x64 arch/x86/entry/common.c:55 [inline]
    do_syscall_64+0x51/0xba arch/x86/entry/common.c:93
    entry_SYSCALL_64_after_hwframe+0x61/0xcb

    -> #2 (rfkill_global_mutex){+.+.}-{3:3}:
    __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599
    __mutex_lock kernel/locking/mutex.c:732 [inline]
    mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784
    rfkill_register+0x30/0x7e3 net/rfkill/core.c:1045
    hci_register_dev+0x48f/0x96d net/bluetooth/hci_core.c:2622
    __vhci_create_device drivers/bluetooth/hci_vhci.c:341 [inline]
    vhci_create_device+0x3ad/0x68f drivers/bluetooth/hci_vhci.c:374
    vhci_get_user drivers/bluetooth/hci_vhci.c:431 [inline]
    vhci_write+0x37b/0x429 drivers/bluetooth/hci_vhci.c:511
    call_write_iter include/linux/fs.h:2109 [inline]
    new_sync_write fs/read_write.c:509 [inline]
    vfs_write+0xaa8/0xcf5 fs/read_write.c:596
    ksys_write+0x19b/0x2bd fs/read_write.c:650
    do_syscall_x64 arch/x86/entry/common.c:55 [inline]
    do_syscall_64+0x51/0xba arch/x86/entry/common.c:93
    entry_SYSCALL_64_after_hwframe+0x61/0xcb

    -> #1 (&data->open_mutex){+.+.}-{3:3}:
    __mutex_lock_common+0x1b6/0x1bc2 kernel/locking/mutex.c:599
    __mutex_lock kernel/locking/mutex.c:732 [inline]
    mutex_lock_nested+0x17/0x1c kernel/locking/mutex.c:784
    vhci_send_frame+0x68/0x9c drivers/bluetooth/hci_vhci.c:75
    hci_send_frame+0x1cc/0x2ff net/bluetooth/hci_core.c:2989
    hci_sched_acl_pkt net/bluetooth/hci_core.c:3498 [inline]
    hci_sched_acl net/bluetooth/hci_core.c:3583 [inline]
    hci_tx_work+0xb94/0x1a60 net/bluetooth/hci_core.c:3654
    process_one_work+0x901/0xfb8 kernel/workqueue.c:2310
    worker_thread+0xa67/0x1003 kernel/workqueue.c:2457
    kthread+0x36a/0x430 kernel/kthread.c:319
    ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:298

    -> #0 ((work_completion)(&hdev->tx_work)){+.+.}-{0:0}:
    check_prev_add kernel/locking/lockdep.c:3053 [inline]
    check_prevs_add kernel/locking/lockdep.c:3172 [inline]
    validate_chain kernel/locking/lockdep.c:3787 [inline]
    __lock_acquire+0x2d32/0x77fa kernel/locking/lockdep.c:5011
    lock_acquire+0x273/0x4d5 kernel/locking/lockdep.c:5622
    __flush_work+0xee/0x19f kernel/workqueue.c:3090
    hci_dev_close_sync+0x32f/0x1113 net/bluetooth/hci_sync.c:4352
    hci_dev_do_close+0x47/0x9f net/bluetooth/hci_core.c:553
    hci_rfkill_set_block+0x130/0x1ac net/bluetooth/hci_core.c:935
    rfkill_set_block+0x1e6/0x3b8 net/rfkill/core.c:345
    rfkill_fop_write+0x2d8/0x672 net/rfkill/core.c:1274
    vfs_write+0x277/0xcf5 fs/read_write.c:594
    ksys_write+0x19b/0x2bd fs/read_write.c:650
    do_syscall_x64 arch/x86/entry/common.c:55 [inline]
    do_syscall_64+0x51/0xba arch/x86/entry/common.c:93
    entry_SYSCALL_64_after_hwframe+0x61/0xcb

This change removes the need for acquiring the open_mutex in
vhci_send_frame, thus eliminating the potential deadlock while
maintaining the required packet ordering.

Fixes: 92d4abd66f70 ("Bluetooth: vhci: Fix race when opening vhci device")
Signed-off-by: Ying Hsu <yinghsu@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

Bluetooth: Fix not notifying when connection encryption changes

[ Upstream commit f67eabffb57d0bee379994a18ec5f462b2cbdf86 ]

Some layers such as SMP depend on getting notified about encryption
changes immediately as they only allow certain PDU to be transmitted
over an encrypted link which may cause SMP implementation to reject
valid PDUs received thus causing pairing to fail when it shouldn't.

Fixes: 7aca0ac4792e ("Bluetooth: Wait for HCI_OP_WRITE_AUTH_PAYLOAD_TO to complete")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/rose: fix races in rose_kill_by_device()

[ Upstream commit 64b8bc7d5f1434c636a40bdcfcd42b278d1714be ]

syzbot found an interesting netdev refcounting issue in
net/rose/af_rose.c, thanks to CONFIG_NET_DEV_REFCNT_TRACKER=y [1]

Problem is that rose_kill_by_device() can change rose->device
while other threads do not expect the pointer to be changed.

We have to first collect sockets in a temporary array,
then perform the changes while holding the socket
lock and rose_list_lock spinlock (in this order)

Change rose_release() to also acquire rose_list_lock
before releasing the netdev refcount.

[1]

[ 1185.055088][ T7889] ref_tracker: reference already released.
[ 1185.061476][ T7889] ref_tracker: allocated in:
[ 1185.066081][ T7889]  rose_bind+0x4ab/0xd10
[ 1185.070446][ T7889]  __sys_bind+0x1ec/0x220
[ 1185.074818][ T7889]  __x64_sys_bind+0x72/0xb0
[ 1185.079356][ T7889]  do_syscall_64+0x40/0x110
[ 1185.083897][ T7889]  entry_SYSCALL_64_after_hwframe+0x63/0x6b
[ 1185.089835][ T7889] ref_tracker: freed in:
[ 1185.094088][ T7889]  rose_release+0x2f5/0x570
[ 1185.098629][ T7889]  __sock_release+0xae/0x260
[ 1185.103262][ T7889]  sock_close+0x1c/0x20
[ 1185.107453][ T7889]  __fput+0x270/0xbb0
[ 1185.111467][ T7889]  task_work_run+0x14d/0x240
[ 1185.116085][ T7889]  get_signal+0x106f/0x2790
[ 1185.120622][ T7889]  arch_do_signal_or_restart+0x90/0x7f0
[ 1185.126205][ T7889]  exit_to_user_mode_prepare+0x121/0x240
[ 1185.131846][ T7889]  syscall_exit_to_user_mode+0x1e/0x60
[ 1185.137293][ T7889]  do_syscall_64+0x4d/0x110
[ 1185.141783][ T7889]  entry_SYSCALL_64_after_hwframe+0x63/0x6b
[ 1185.148085][ T7889] ------------[ cut here ]------------

WARNING: CPU: 1 PID: 7889 at lib/ref_tracker.c:255 ref_tracker_free+0x61a/0x810 lib/ref_tracker.c:255
Modules linked in:
CPU: 1 PID: 7889 Comm: syz-executor.2 Not tainted 6.7.0-rc4-syzkaller-00162-g65c95f78917e #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/10/2023
RIP: 0010:ref_tracker_free+0x61a/0x810 lib/ref_tracker.c:255
Code: 00 44 8b 6b 18 31 ff 44 89 ee e8 21 62 f5 fc 45 85 ed 0f 85 a6 00 00 00 e8 a3 66 f5 fc 48 8b 34 24 48 89 ef e8 27 5f f1 05 90 <0f> 0b 90 bb ea ff ff ff e9 52 fd ff ff e8 84 66 f5 fc 4c 8d 6d 44
RSP: 0018:ffffc90004917850 EFLAGS: 00010202
RAX: 0000000000000201 RBX: ffff88802618f4c0 RCX: 0000000000000000
RDX: 0000000000000202 RSI: ffffffff8accb920 RDI: 0000000000000001
RBP: ffff8880269ea5b8 R08: 0000000000000001 R09: fffffbfff23e35f6
R10: ffffffff91f1afb7 R11: 0000000000000001 R12: 1ffff92000922f0c
R13: 0000000005a2039b R14: ffff88802618f4d8 R15: 00000000ffffffff
FS: 00007f0a720ef6c0(0000) GS:ffff8880b9900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f43a819d988 CR3: 0000000076c64000 CR4: 00000000003506f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
netdev_tracker_free include/linux/netdevice.h:4127 [inline]
netdev_put include/linux/netdevice.h:4144 [inline]
netdev_put include/linux/netdevice.h:4140 [inline]
rose_kill_by_device net/rose/af_rose.c:195 [inline]
rose_device_event+0x25d/0x330 net/rose/af_rose.c:218
notifier_call_chain+0xb6/0x3b0 kernel/notifier.c:93
call_netdevice_notifiers_info+0xbe/0x130 net/core/dev.c:1967
call_netdevice_notifiers_extack net/core/dev.c:2005 [inline]
call_netdevice_notifiers net/core/dev.c:2019 [inline]
__dev_notify_flags+0x1f5/0x2e0 net/core/dev.c:8646
dev_change_flags+0x122/0x170 net/core/dev.c:8682
dev_ifsioc+0x9ad/0x1090 net/core/dev_ioctl.c:529
dev_ioctl+0x224/0x1090 net/core/dev_ioctl.c:786
sock_do_ioctl+0x198/0x270 net/socket.c:1234
sock_ioctl+0x22e/0x6b0 net/socket.c:1339
vfs_ioctl fs/ioctl.c:51 [inline]
__do_sys_ioctl fs/ioctl.c:871 [inline]
__se_sys_ioctl fs/ioctl.c:857 [inline]
__x64_sys_ioctl+0x18f/0x210 fs/ioctl.c:857
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x63/0x6b
RIP: 0033:0x7f0a7147cba9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 e1 20 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007f0a720ef0c8 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
RAX: ffffffffffffffda RBX: 00007f0a7159bf80 RCX: 00007f0a7147cba9
RDX: 0000000020000040 RSI: 0000000000008914 RDI: 0000000000000004
RBP: 00007f0a714c847a R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007f0a7159bf80 R15: 00007ffc8bb3a5f8
</TASK>

Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Bernard Pidoux <f6bvp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

ethernet: atheros: fix a memleak in atl1e_setup_ring_resources

[ Upstream commit 309fdb1c33fe726d92d0030481346f24e1b01f07 ]

In the error handling of 'offset > adapter->ring_size', the
tx_ring->tx_buffer allocated by kzalloc should be freed,
instead of 'goto failed' instantly.

Fixes: a6a5325239c2 ("atl1e: Atheros L1E Gigabit Ethernet driver")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Reviewed-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: sched: ife: fix potential use-after-free

[ Upstream commit 19391a2ca98baa7b80279306cdf7dd43f81fa595 ]

ife_decode() calls pskb_may_pull() two times, we need to reload
ifehdr after the second one, or risk use-after-free as reported
by syzbot:

BUG: KASAN: slab-use-after-free in __ife_tlv_meta_valid net/ife/ife.c:108 [inline]
BUG: KASAN: slab-use-after-free in ife_tlv_meta_decode+0x1d1/0x210 net/ife/ife.c:131
Read of size 2 at addr ffff88802d7300a4 by task syz-executor.5/22323

CPU: 0 PID: 22323 Comm: syz-executor.5 Not tainted 6.7.0-rc3-syzkaller-00804-g074ac38d5b95 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 11/10/2023
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xd9/0x1b0 lib/dump_stack.c:106
print_address_description mm/kasan/report.c:364 [inline]
print_report+0xc4/0x620 mm/kasan/report.c:475
kasan_report+0xda/0x110 mm/kasan/report.c:588
__ife_tlv_meta_valid net/ife/ife.c:108 [inline]
ife_tlv_meta_decode+0x1d1/0x210 net/ife/ife.c:131
tcf_ife_decode net/sched/act_ife.c:739 [inline]
tcf_ife_act+0x4e3/0x1cd0 net/sched/act_ife.c:879
tc_act include/net/tc_wrapper.h:221 [inline]
tcf_action_exec+0x1ac/0x620 net/sched/act_api.c:1079
tcf_exts_exec include/net/pkt_cls.h:344 [inline]
mall_classify+0x201/0x310 net/sched/cls_matchall.c:42
tc_classify include/net/tc_wrapper.h:227 [inline]
__tcf_classify net/sched/cls_api.c:1703 [inline]
tcf_classify+0x82f/0x1260 net/sched/cls_api.c:1800
hfsc_classify net/sched/sch_hfsc.c:1147 [inline]
hfsc_enqueue+0x315/0x1060 net/sched/sch_hfsc.c:1546
dev_qdisc_enqueue+0x3f/0x230 net/core/dev.c:3739
__dev_xmit_skb net/core/dev.c:3828 [inline]
__dev_queue_xmit+0x1de1/0x3d30 net/core/dev.c:4311
dev_queue_xmit include/linux/netdevice.h:3165 [inline]
packet_xmit+0x237/0x350 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x24aa/0x5200 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
__sys_sendto+0x255/0x340 net/socket.c:2190
__do_sys_sendto net/socket.c:2202 [inline]
__se_sys_sendto net/socket.c:2198 [inline]
__x64_sys_sendto+0xe0/0x1b0 net/socket.c:2198
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b
RIP: 0033:0x7fe9acc7cae9
Code: 28 00 00 00 75 05 48 83 c4 28 c3 e8 e1 20 00 00 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007fe9ada450c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 00007fe9acd9bf80 RCX: 00007fe9acc7cae9
RDX: 000000000000fce0 RSI: 00000000200002c0 RDI: 0000000000000003
RBP: 00007fe9accc847a R08: 0000000020000140 R09: 0000000000000014
R10: 0000000000000004 R11: 0000000000000246 R12: 0000000000000000
R13: 000000000000000b R14: 00007fe9acd9bf80 R15: 00007ffd5427ae78
</TASK>

Allocated by task 22323:
kasan_save_stack+0x33/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
____kasan_kmalloc mm/kasan/common.c:374 [inline]
__kasan_kmalloc+0xa2/0xb0 mm/kasan/common.c:383
kasan_kmalloc include/linux/kasan.h:198 [inline]
__do_kmalloc_node mm/slab_common.c:1007 [inline]
__kmalloc_node_track_caller+0x5a/0x90 mm/slab_common.c:1027
kmalloc_reserve+0xef/0x260 net/core/skbuff.c:582
__alloc_skb+0x12b/0x330 net/core/skbuff.c:651
alloc_skb include/linux/skbuff.h:1298 [inline]
alloc_skb_with_frags+0xe4/0x710 net/core/skbuff.c:6331
sock_alloc_send_pskb+0x7e4/0x970 net/core/sock.c:2780
packet_alloc_skb net/packet/af_packet.c:2930 [inline]
packet_snd net/packet/af_packet.c:3024 [inline]
packet_sendmsg+0x1e2a/0x5200 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
__sys_sendto+0x255/0x340 net/socket.c:2190
__do_sys_sendto net/socket.c:2202 [inline]
__se_sys_sendto net/socket.c:2198 [inline]
__x64_sys_sendto+0xe0/0x1b0 net/socket.c:2198
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b

Freed by task 22323:
kasan_save_stack+0x33/0x50 mm/kasan/common.c:45
kasan_set_track+0x25/0x30 mm/kasan/common.c:52
kasan_save_free_info+0x2b/0x40 mm/kasan/generic.c:522
____kasan_slab_free mm/kasan/common.c:236 [inline]
____kasan_slab_free+0x15b/0x1b0 mm/kasan/common.c:200
kasan_slab_free include/linux/kasan.h:164 [inline]
slab_free_hook mm/slub.c:1800 [inline]
slab_free_freelist_hook+0x114/0x1e0 mm/slub.c:1826
slab_free mm/slub.c:3809 [inline]
__kmem_cache_free+0xc0/0x180 mm/slub.c:3822
skb_kfree_head net/core/skbuff.c:950 [inline]
skb_free_head+0x110/0x1b0 net/core/skbuff.c:962
pskb_expand_head+0x3c5/0x1170 net/core/skbuff.c:2130
__pskb_pull_tail+0xe1/0x1830 net/core/skbuff.c:2655
pskb_may_pull_reason include/linux/skbuff.h:2685 [inline]
pskb_may_pull include/linux/skbuff.h:2693 [inline]
ife_decode+0x394/0x4f0 net/ife/ife.c:82
tcf_ife_decode net/sched/act_ife.c:727 [inline]
tcf_ife_act+0x43b/0x1cd0 net/sched/act_ife.c:879
tc_act include/net/tc_wrapper.h:221 [inline]
tcf_action_exec+0x1ac/0x620 net/sched/act_api.c:1079
tcf_exts_exec include/net/pkt_cls.h:344 [inline]
mall_classify+0x201/0x310 net/sched/cls_matchall.c:42
tc_classify include/net/tc_wrapper.h:227 [inline]
__tcf_classify net/sched/cls_api.c:1703 [inline]
tcf_classify+0x82f/0x1260 net/sched/cls_api.c:1800
hfsc_classify net/sched/sch_hfsc.c:1147 [inline]
hfsc_enqueue+0x315/0x1060 net/sched/sch_hfsc.c:1546
dev_qdisc_enqueue+0x3f/0x230 net/core/dev.c:3739
__dev_xmit_skb net/core/dev.c:3828 [inline]
__dev_queue_xmit+0x1de1/0x3d30 net/core/dev.c:4311
dev_queue_xmit include/linux/netdevice.h:3165 [inline]
packet_xmit+0x237/0x350 net/packet/af_packet.c:276
packet_snd net/packet/af_packet.c:3081 [inline]
packet_sendmsg+0x24aa/0x5200 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
__sys_sendto+0x255/0x340 net/socket.c:2190
__do_sys_sendto net/socket.c:2202 [inline]
__se_sys_sendto net/socket.c:2198 [inline]
__x64_sys_sendto+0xe0/0x1b0 net/socket.c:2198
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82
entry_SYSCALL_64_after_hwframe+0x63/0x6b

The buggy address belongs to the object at ffff88802d730000
which belongs to the cache kmalloc-8k of size 8192
The buggy address is located 164 bytes inside of
freed 8192-byte region [ffff88802d730000, ffff88802d732000)

The buggy address belongs to the physical page:
page:ffffea0000b5cc00 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x2d730
head:ffffea0000b5cc00 order:3 entire_mapcount:0 nr_pages_mapped:0 pincount:0
flags: 0xfff00000000840(slab|head|node=0|zone=1|lastcpupid=0x7ff)
page_type: 0xffffffff()
raw: 00fff00000000840 ffff888013042280 dead000000000122 0000000000000000
raw: 0000000000000000 0000000080020002 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
page_owner tracks the page as allocated
page last allocated via order 3, migratetype Unmovable, gfp_mask 0x1d20c0(__GFP_IO|__GFP_FS|__GFP_NOWARN|__GFP_NORETRY|__GFP_COMP|__GFP_NOMEMALLOC|__GFP_HARDWALL), pid 22323, tgid 22320 (syz-executor.5), ts 950317230369, free_ts 950233467461
set_page_owner include/linux/page_owner.h:31 [inline]
post_alloc_hook+0x2d0/0x350 mm/page_alloc.c:1544
prep_new_page mm/page_alloc.c:1551 [inline]
get_page_from_freelist+0xa28/0x3730 mm/page_alloc.c:3319
__alloc_pages+0x22e/0x2420 mm/page_alloc.c:4575
alloc_pages_mpol+0x258/0x5f0 mm/mempolicy.c:2133
alloc_slab_page mm/slub.c:1870 [inline]
allocate_slab mm/slub.c:2017 [inline]
new_slab+0x283/0x3c0 mm/slub.c:2070
___slab_alloc+0x979/0x1500 mm/slub.c:3223
__slab_alloc.constprop.0+0x56/0xa0 mm/slub.c:3322
__slab_alloc_node mm/slub.c:3375 [inline]
slab_alloc_node mm/slub.c:3468 [inline]
__kmem_cache_alloc_node+0x131/0x310 mm/slub.c:3517
__do_kmalloc_node mm/slab_common.c:1006 [inline]
__kmalloc_node_track_caller+0x4a/0x90 mm/slab_common.c:1027
kmalloc_reserve+0xef/0x260 net/core/skbuff.c:582
__alloc_skb+0x12b/0x330 net/core/skbuff.c:651
alloc_skb include/linux/skbuff.h:1298 [inline]
alloc_skb_with_frags+0xe4/0x710 net/core/skbuff.c:6331
sock_alloc_send_pskb+0x7e4/0x970 net/core/sock.c:2780
packet_alloc_skb net/packet/af_packet.c:2930 [inline]
packet_snd net/packet/af_packet.c:3024 [inline]
packet_sendmsg+0x1e2a/0x5200 net/packet/af_packet.c:3113
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xd5/0x180 net/socket.c:745
__sys_sendto+0x255/0x340 net/socket.c:2190
page last free stack trace:
reset_page_owner include/linux/page_owner.h:24 [inline]
free_pages_prepare mm/page_alloc.c:1144 [inline]
free_unref_page_prepare+0x53c/0xb80 mm/page_alloc.c:2354
free_unref_page+0x33/0x3b0 mm/page_alloc.c:2494
__unfreeze_partials+0x226/0x240 mm/slub.c:2655
qlink_free mm/kasan/quarantine.c:168 [inline]
qlist_free_all+0x6a/0x170 mm/kasan/quarantine.c:187
kasan_quarantine_reduce+0x18e/0x1d0 mm/kasan/quarantine.c:294
__kasan_slab_alloc+0x65/0x90 mm/kasan/common.c:305
kasan_slab_alloc include/linux/kasan.h:188 [inline]
slab_post_alloc_hook mm/slab.h:763 [inline]
slab_alloc_node mm/slub.c:3478 [inline]
slab_alloc mm/slub.c:3486 [inline]
__kmem_cache_alloc_lru mm/slub.c:3493 [inline]
kmem_cache_alloc_lru+0x219/0x6f0 mm/slub.c:3509
alloc_inode_sb include/linux/fs.h:2937 [inline]
ext4_alloc_inode+0x28/0x650 fs/ext4/super.c:1408
alloc_inode+0x5d/0x220 fs/inode.c:261
new_inode_pseudo fs/inode.c:1006 [inline]
new_inode+0x22/0x260 fs/inode.c:1032
__ext4_new_inode+0x333/0x5200 fs/ext4/ialloc.c:958
ext4_symlink+0x5d7/0xa20 fs/ext4/namei.c:3398
vfs_symlink fs/namei.c:4464 [inline]
vfs_symlink+0x3e5/0x620 fs/namei.c:4448
do_symlinkat+0x25f/0x310 fs/namei.c:4490
__do_sys_symlinkat fs/namei.c:4506 [inline]
__se_sys_symlinkat fs/namei.c:4503 [inline]
__x64_sys_symlinkat+0x97/0xc0 fs/namei.c:4503
do_syscall_x64 arch/x86/entry/common.c:51 [inline]
do_syscall_64+0x40/0x110 arch/x86/entry/common.c:82

Fixes: d57493d6d1be ("net: sched: ife: check on metadata length")
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Alexander Aring <aahringo@redhat.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: Return error from sk_stream_wait_connect() if sk_wait_event() fails

[ Upstream commit cac23b7d7627915d967ce25436d7aae26e88ed06 ]

The following NULL pointer dereference issue occurred:

BUG: kernel NULL pointer dereference, address: 0000000000000000
<...>
RIP: 0010:ccid_hc_tx_send_packet net/dccp/ccid.h:166 [inline]
RIP: 0010:dccp_write_xmit+0x49/0x140 net/dccp/output.c:356
<...>
Call Trace:
 <TASK>
 dccp_sendmsg+0x642/0x7e0 net/dccp/proto.c:801
 inet_sendmsg+0x63/0x90 net/ipv4/af_inet.c:846
 sock_sendmsg_nosec net/socket.c:730 [inline]
 __sock_sendmsg+0x83/0xe0 net/socket.c:745
 ____sys_sendmsg+0x443/0x510 net/socket.c:2558
 ___sys_sendmsg+0xe5/0x150 net/socket.c:2612
 __sys_sendmsg+0xa6/0x120 net/socket.c:2641
 __do_sys_sendmsg net/socket.c:2650 [inline]
 __se_sys_sendmsg net/socket.c:2648 [inline]
 __x64_sys_sendmsg+0x45/0x50 net/socket.c:2648
 do_syscall_x64 arch/x86/entry/common.c:51 [inline]
 do_syscall_64+0x43/0x110 arch/x86/entry/common.c:82
 entry_SYSCALL_64_after_hwframe+0x63/0x6b

sk_wait_event() returns an error (-EPIPE) if disconnect() is called on the
socket waiting for the event. However, sk_stream_wait_connect() returns
success, i.e. zero, even if sk_wait_event() returns -EPIPE, so a function
that waits for a connection with sk_stream_wait_connect() may misbehave.

In the case of the above DCCP issue, dccp_sendmsg() is waiting for the
connection. If disconnect() is called in concurrently, the above issue
occurs.

This patch fixes the issue by returning error from sk_stream_wait_connect()
if sk_wait_event() fails.

Fixes: 419ce133ab92 ("tcp: allow again tcp_disconnect() when threads are waiting")
Signed-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Reported-by: syzbot+c71bc336c5061153b502@syzkaller.appspotmail.com
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reported-by: syzkaller <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

octeontx2-pf: Fix graceful exit during PFC configuration failure

[ Upstream commit 8c97ab5448f2096daba11edf8d18a44e1eb6f31d ]

During PFC configuration failure the code was not handling a graceful
exit. This patch fixes the same and add proper code for a graceful exit.

Fixes: 99c969a83d82 ("octeontx2-pf: Add egress PFC support")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mscc: ocelot: fix pMAC TX RMON stats for bucket 256-511 and above

[ Upstream commit 70f010da00f90415296f93fb47a561977eae41cb ]

The typo from ocelot_port_rmon_stats_cb() was also carried over to
ocelot_port_pmac_rmon_stats_cb() as well, leading to incorrect TX RMON
stats for the pMAC too.

Fixes: ab3f97a9610a ("net: mscc: ocelot: export ethtool MAC Merge stats for Felix VSC9959")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231214000902.545625-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net: mscc: ocelot: fix eMAC TX RMON stats for bucket 256-511 and above

[ Upstream commit 52eda4641d041667fa059f4855c5f88dcebd8afe ]

There is a typo in the driver due to which we report incorrect TX RMON
counters for the 256-511 octet bucket and all the other buckets larger
than that.

Bug found with the selftest at
https://patchwork.kernel.org/project/netdevbpf/patch/20231211223346.2497157-9-tobias@waldekranz.com/

Fixes: e32036e1ae7b ("net: mscc: ocelot: add support for all sorts of standardized counters present in DSA")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20231214000902.545625-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Correct snprintf truncation handling for fw_version buffer used by representors

[ Upstream commit b13559b76157de9d74f04d3ca0e49d69de3b5675 ]

snprintf returns the length of the formatted string, excluding the trailing
null, without accounting for truncation. This means that is the return
value is greater than or equal to the size parameter, the fw_version string
was truncated.

Link: https://docs.kernel.org/core-api/kernel-api.html#c.snprintf
Fixes: 1b2bd0c0264f ("net/mlx5e: Check return value of snprintf writing to fw_version buffer for representors")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Correct snprintf truncation handling for fw_version buffer

[ Upstream commit ad436b9c1270c40554e274f067f1b78fcc06a004 ]

snprintf returns the length of the formatted string, excluding the trailing
null, without accounting for truncation. This means that is the return
value is greater than or equal to the size parameter, the fw_version string
was truncated.

Reported-by: David Laight <David.Laight@ACULAB.COM>
Closes: https://lore.kernel.org/netdev/81cae734ee1b4cde9b380a9a31006c1a@AcuMS.aculab.com/
Link: https://docs.kernel.org/core-api/kernel-api.html#c.snprintf
Fixes: 41e63c2baa11 ("net/mlx5e: Check return value of snprintf writing to fw_version buffer")
Signed-off-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Fix error codes in alloc_branch_attr()

[ Upstream commit d792e5f7f19b95f5ce41ac49df5ead4d280238f4 ]

Set the error code if set_branch_dest_ft() fails.

Fixes: ccbe33003b10 ("net/mlx5e: TC, Don't offload post action rule if not supported")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

net/mlx5e: Fix error code in mlx5e_tc_action_miss_mapping_get()

[ Upstream commit 86d5922679f3b6d02a64df66cdd777fdd4ea5c0d ]

Preserve the error code if esw_add_restore_rule() fails.  Don't return
success.

Fixes: 6702782845a5 ("net/mlx5e: TC, Set CT miss to the specific ct action instance")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>