mac80211: Do not disconnect on invalid operating class

[ Upstream commit 191da271ac260700db3e5b4bb982a17ca78769d6 ]

Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.

However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.

To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

cfg80211: clear wep keys after disconnection

[ Upstream commit 3027a8e799b20fc922496a12f8ad2f9f36a8a696 ]

When a low level driver calls cfg80211_disconnected(), wep keys are
not cleared. As a result, following connection requests will fail
since cfg80211 internal state shows a connection is still in progress.

Fix this by clearing the wep keys when disconnecting.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix calling sleeping function in atomic context

[ Upstream commit 95f3ce6a77893ac828ba841df44421620de4314b ]

sta_info_alloc can be called from atomic paths (such as RX path)
so we need to call pcpu_alloc with the correct gfp.

Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix a possible leak of station stats

[ Upstream commit d78d9ee9d40aca4781d2c5334972544601a4c3a2 ]

If sta_info_alloc fails after allocating the per CPU statistics,
they are not properly freed.

Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4

[ Upstream commit 651b9920d7a694ffb1f885aef2bbb068a25d9d66 ]

This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xfrm: do not call rcu_read_unlock when afinfo is NULL in xfrm_get_tos

[ Upstream commit 143a4454daaf0e80a2b9f37159a0d6d2b61e64ed ]

When xfrm_policy_get_afinfo returns NULL, it will not hold rcu
read lock. In this case, rcu_read_unlock should not be called
in xfrm_get_tos, just like other places where it's calling
xfrm_policy_get_afinfo.

Fixes: f5e2bb4f5b22 ("xfrm: policy: xfrm_get_tos cannot fail")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/dasd: fix handling of internal requests

[ Upstream commit 9487cfd3430d07366801886bdf185799a2b6f066 ]

Internal DASD device driver I/O such as query host access count or
path verification is started using the _sleep_on() function.
To mark a request as started or ended the callback_data is set to either
DASD_SLEEPON_START_TAG or DASD_SLEEPON_END_TAG.

In cases where the request has to be stopped unconditionally the status is
set to DASD_SLEEPON_END_TAG as well which leads to immediate clearing of
the request.
But the request might still be on a device request queue for normal
operation which might lead to a panic because of a BUG() statement in
__dasd_device_process_final_queue() or a list corruption of the device
request queue.

Fix by removing the setting of DASD_SLEEPON_END_TAG in the
dasd_cancel_req() and dasd_generic_requeue_all_requests() functions and
ensure that the request is not deleted in the requeue function.
Trigger the device tasklet in the requeue function and let the normal
processing cleanup the request.

Signed-off-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Reviewed-by: Jan Hoeppner <hoeppner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md: fix md_write_start() deadlock w/o metadata devices

[ Upstream commit 4b6c1060eaa6495aa5b0032e8f2d51dd936b1257 ]

If no metadata devices are configured on raid1/4/5/6/10
(e.g. via dm-raid), md_write_start() unconditionally waits
for superblocks to be written thus deadlocking.

Fix introduces mddev->has_superblocks bool, defines it in md_run()
and checks for it in md_write_start() to conditionally avoid waiting.

Once on it, check for non-existing superblocks in md_super_write().

Link: https://bugzilla.kernel.org/show_bug.cgi?id=198647
Fixes: cc27b0c78c796 ("md: fix deadlock between mddev_suspend() and md_write_start()")

Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MD: Free bioset when md_run fails

[ Upstream commit b126194cbb799f9980b92a77e58db6ad794c8082 ]

Signed-off-by: Xiao Ni <xni@redhat.com>
Acked-by: Guoqing Jiang <gqjiang@suse.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rxrpc: Work around usercopy check

[ Upstream commit a16b8d0cf2ec1e626d24bc2a7b9e64ace6f7501d ]

Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted.  This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer.  A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.

Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().

The warning generated looks like:

Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'dmaengine-unmap-128' (offset 680, size 8)!
WARNING: CPU: 0 PID: 1401 at mm/usercopy.c:81 usercopy_warn+0x7e/0xa0
...
RIP: 0010:usercopy_warn+0x7e/0xa0
...
Call Trace:
 __check_object_size+0x9c/0x1a0
 put_cmsg+0x98/0x120
 rxrpc_recvmsg+0x6fc/0x1010 [rxrpc]
 ? finish_wait+0x80/0x80
 ___sys_recvmsg+0xf8/0x240
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? finish_task_switch+0xa6/0x2b0
 ? trace_hardirqs_on_caller+0xed/0x180
 ? _raw_spin_unlock_irq+0x29/0x40
 ? __sys_recvmsg+0x4e/0x90
 __sys_recvmsg+0x4e/0x90
 do_syscall_64+0x7a/0x220
 entry_SYSCALL_64_after_hwframe+0x26/0x9b

Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NFC: llcp: Limit size of SDP URI

[ Upstream commit fe9c842695e26d8116b61b80bfb905356f07834b ]

The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.

Fixes: d9b8d8e19b073 ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: always init rs with 20mhz bandwidth rates

[ Upstream commit 6b7a5aea71b342ec0593d23b08383e1f33da4c9a ]

In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.

Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix IBSS for devices that support station type API

[ Upstream commit fc07bd8ce19bff9e7479c04077ddb5957d1a27be ]

In IBSS, the mac80211 sets the cab_queue to be invalid.

However, the multicast station uses it, so we need to override it.

A previous patch did it, but it was nested inside the if's and was
applied only for legacy FWs that don't support the new station type
API, instead of being applied for all paths.

In addition, add a missing NL80211_IFTYPE_ADHOC to the initialization
of the queues in iwl_mvm_mac_ctxt_init()

Fixes: ee48b72211f8 ("iwlwifi: mvm: support ibss in dqa mode")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix security bug in PN checking

[ Upstream commit 5ab2ba931255d8bf03009c06d58dce97de32797c ]

A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.

This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.

Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.

Fixes: f1ae02b186d9 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: rockchip: Fix DWMMC clocks

[ Upstream commit e78c637127ee7683d606737f2e62b5da6fd7b1c3 ]

Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.

This error has propagated across the 32-bit DTs too, so fix those up.

Fixes: 187d7967a5ee ("ARM: dts: rockchip: add the sdio/sdmmc node for rk3036")
Fixes: faea098e1808 ("ARM: dts: rockchip: add core rk3036 dtsi")
Fixes: 9848ebeb952d ("ARM: dts: rockchip: add core rk3228 dtsi")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: rockchip: Fix DWMMC clocks

[ Upstream commit ca9eee95a2decc6f60bed65b5b836a26bff825c1 ]

Trying to boot an RK3328 box with an HS200-capable eMMC, I see said eMMC
fail to initialise as it can't run its tuning procedure, because the
sample clock is missing. Upon closer inspection, whilst the clock is
present in the DT, its name is subtly incorrect per the binding, so
__of_clk_get_by_name() never finds it. By inspection, the drive clock
suffers from a similar problem, so has never worked properly either.

Fix up all instances of the incorrect clock names across the 64-bit DTs.

Fixes: d717f7352ec6 ("arm64: dts: rockchip: add sdmmc/sdio/emmc nodes for RK3328 SoCs")
Fixes: b790c2cab5ca ("arm64: dts: add Rockchip rk3368 core dtsi and board dts for the r88 board")
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/uverbs: Fix unbalanced unlock on error path for rdma_explicit_destroy

[ Upstream commit ec6f8401c48a86809237e86878a6fac6b281118f ]

If remove_commit fails then the lock is left locked while the uobj still
exists. Eventually the kernel will deadlock.

lockdep detects this and says:

 test/4221 is leaving the kernel with locks still held!
 1 lock held by test/4221:
  #0:  (&ucontext->cleanup_rwsem){.+.+}, at: [<000000001e5c7523>] rdma_explicit_destroy+0x37/0x120 [ib_uverbs]

Fixes: 4da70da23e9b ("IB/core: Explicitly destroy an object while keeping uobject")
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/uverbs: Fix possible oops with duplicate ioctl attributes

[ Upstream commit 4d39a959bc1f3d164b5a54147fdeb19f84b1ed58 ]

If the same attribute is listed twice by the user in the ioctl attribute
list then error unwind can cause the kernel to deref garbage.

This happens when an object with WRITE access is sent twice. The second
parse properly fails but corrupts the state required for the error unwind
it triggers.

Fixing this by making duplicates in the attribute list invalid. This is
not something we need to support.

The ioctl interface is currently recommended to be disabled in kConfig.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/uverbs: Fix method merging in uverbs_ioctl_merge

[ Upstream commit 3d89459e2ef92cc0e5a50dde868780ccda9786c1 ]

Fix a bug in uverbs_ioctl_merge that looked at the object's iterator
number instead of the method's iterator number when merging methods.

While we're at it, make the uverbs_ioctl_merge code a bit more clear
and faster.

Fixes: 118620d3686b ('IB/core: Add uverbs merge trees functionality')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xhci: workaround for AMD Promontory disabled ports wakeup

[ Upstream commit bde0716d1f076e4c913c7946bcc858f71243c7a0 ]

For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.

[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

tls: retrun the correct IV in getsockopt

[ Upstream commit a1dfa6812b682eef750412dd5a90e7d38d7af068 ]

Current code returns four bytes of salt followed by four bytes of IV.
This patch returns all eight bytes of IV.

fixes: 3c4d7559159b ("tls: kernel TLS support")
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmvnic: Clean RX pool buffers during device close

[ Upstream commit d0869c0071e40c4407d1a4d7c9497653cf47253b ]

During device close or reset, there were some cases of outstanding
RX socket buffers not being freed. Include a function similar to the
one that already exists to clean TX socket buffers in this case.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmvnic: Free RX socket buffer in case of adapter error

[ Upstream commit 4b9b0f01350500173f17e2b2e65beb4df4ef99c7 ]

If a RX buffer is returned to the client driver with an error, free the
corresponding socket buffer before continuing.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmvnic: Wait until reset is complete to set carrier on

[ Upstream commit cc85c02edfe48a34865ae00f7d22298a3fdd17aa ]

Pushes back setting the carrier on until the end of the reset
code. This resolves a bug where a watchdog timer was detecting
that a TX queue had stalled before the adapter reset was complete.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP1: clock: Fix debugfs_create_*() usage

[ Upstream commit 8cbbf1745dcde7ba7e423dc70619d223de90fd43 ]

When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.

Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.

Correct all wrong usage:
  - clk.rate is unsigned long, not u32,
  - clk.flags is u8, not u32, which exposed the successive
    clk.rate_offset and clk.src_offset fields.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP2+: Fix sar_base inititalization for HS omaps

[ Upstream commit fe27f16794f313f5fc16f6d2f42d8c2b2f4d70cc ]

HS omaps use irq_save_secure_context() instead of irq_save_context()
so sar_base will never get initialized and irq_sar_clear() gets called
with a wrong address for HS omaps from irq_restore_context().

Starting with commit f4b9f40ae95b ("ARM: OMAP4+: Initialize SAR RAM
base early for proper CPU1 reset for kexec") we have it available,
and this ideally would been fixed with that commit already.

Fixes: f4b9f40ae95b ("ARM: OMAP4+: Initialize SAR RAM base early for
proper CPU1 reset for kexec")
Cc: Andrew F. Davis <afd@ti.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Santosh Shilimkar <ssantosh@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP3: Fix prm wake interrupt for resume

[ Upstream commit d3be6d2a08bd26580562d9714d3d97ea9ba22c73 ]

For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.

Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.

For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.

And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.

This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.

Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().

In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.

Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt

[ Upstream commit db35340c536f1af0108ec9a0b2126a05d358d14a ]

When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().

In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.

That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.

To fix it, allocate the property dynamically, and delete static one.

Signed-off-by: Qi Hou <qi.hou@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: memfd: add config fragment for fuse

[ Upstream commit 9a606f8d55cfc932ec02172aaed4124fdc150047 ]

The memfd test requires to insert the fuse module (CONFIG_FUSE_FS).

Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: pstore: Adding config fragment CONFIG_PSTORE_RAM=m

[ Upstream commit 9a379e77033f02c4a071891afdf0f0a01eff8ccb ]

pstore_tests and pstore_post_reboot_tests need CONFIG_PSTORE_RAM=m

Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftest/vDSO: fix O=

[ Upstream commit 70b574e7d719bdf96d26528cb289f3e782e83979 ]

The vDSO selftests ignored the O= or KBUILD_OUTPUT= parameters. Fix it.

Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: sync: missing CFLAGS while compiling

[ Upstream commit b2c93e300a11b419b4c67ce08e16fa1436d8118c ]

Based on patch: https://patchwork.kernel.org/patch/10042045/

arch64-linux-gnu-gcc -c sync.c -o sync/sync.o
sync.c:42:29: fatal error: linux/sync_file.h: No such file or directory
 #include <linux/sync_file.h>
                             ^
CFLAGS is not used during the compile step, so the system instead of
kernel headers are used.  Fix this by adding CFLAGS to the OBJS compile
rule.

Reported-by: Lei Yang <Lei.Yang@windriver.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: Fix compile warning with ATA_DEBUG enabled

[ Upstream commit 0d3e45bc6507bd1f8728bf586ebd16c2d9e40613 ]

This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:

  drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
  ./include/linux/kern_levels.h:5:18: warning: format '%d' expects
  argument of type 'int', but argument 6 has type 'u64 {aka long
   long unsigned int}' [-Wformat=]

tj: Patch hand-applied and description trimmed.

Signed-off-by: Dong Bo <dongbo4@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: rockchip: correct ep-gpios for rk3399-sapphire

[ Upstream commit 2b7d2ed1af2e2c0c90a1a8b97926b7b6c6cb03ed ]

The endpoint control gpio for rk3399-sapphire boards is gpio2_a4,
so correct it now.

Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: dts: rockchip: fix rock64 gmac2io stability issues

[ Upstream commit 73e42e18669934fa96cf2bb54291da54177076d7 ]

This commit enables thresh dma mode as this forces to disable checksuming,
and chooses delay values which make the interface stable.

These changes are needed, because ROCK64 is faced with two problems:
1. tx checksuming does not work with packets larger than 1498,
2. the default delays for tx/rx are not stable when using 1Gbps connection.

Delays were found out with:
https://github.com/ayufan-rock64/linux-build/tree/master/recipes/gmac-delays-test

Signed-off-by: Kamil Trzciński <ayufan@ayufan.eu>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ptr_ring: prevent integer overflow when calculating size

[ Upstream commit 54e02162d4454a99227f520948bf4494c3d972d0 ]

Switch to use dividing to prevent integer overflow when size is too
big to calculate allocation size properly.

Reported-by: Eric Biggers <ebiggers3@gmail.com>
Fixes: 6e6e41c31122 ("ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: Fix malformed ARC_EMUL_UNALIGNED default

[ Upstream commit 827cc2fa024dd6517d62de7a44c7b42f32af371b ]

'default N' should be 'default n', though they happen to have the same
effect here, due to undefined symbols (N in this case) evaluating to n
in a tristate sense.

Remove the default from ARC_EMUL_UNALIGNED instead of changing it. bool
and tristate symbols implicitly default to n.

Discovered with the
https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_ulfalizer_Kconfiglib_blob_master_examples_list-5Fundefined.py&d=DwIBAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=c14YS-cH-kdhTOW89KozFhBtBJgs1zXscZojEZQ0THs&m=WxxD8ozR7QQUVzNCBksiznaisBGO_crN7PBOvAoju8s&s=1LmxsNqxwT-7wcInVpZ6Z1J27duZKSoyKxHIJclXU_M&e=
script.

Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: mesh: fix wrong mesh TTL offset calculation

[ Upstream commit c4de37ee2b55deac7d6aeac33e02e3d6be243898 ]

mesh TTL offset in Mesh Channel Switch Parameters element depends on
not only Secondary Channel Offset element, but also affected by
HT Control field and Wide Bandwidth Channel Switch element.
So use element structure to manipulate mesh channel swich param IE
after removing its constant attribution to correct the miscalculation.

Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: generic: Fix machine compatible matching

[ Upstream commit 9a9ab3078e2744a1a55163cfaec73a5798aae33e ]

We now have a platform (Ranchu) in the "generic" platform which matches
based on the FDT compatible string using mips_machine_is_compatible(),
however that function doesn't stop at a blank struct
of_device_id::compatible as that is an array in the struct, not a
pointer to a string.

Fix the loop completion to check the first byte of the compatible array
rather than the address of the compatible array in the struct.

Fixes: eed0eabd12ef ("MIPS: generic: Introduce generic DT-based board support")
Signed-off-by: James Hogan <jhogan@kernel.org>
Reviewed-by: Paul Burton <paul.burton@mips.com>
Reviewed-by: Matt Redfearn <matt.redfearn@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/18580/
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Add support for a store forwarding barrier at kernel entry/exit

commit a048a07d7f4535baa4cbad6bc024f175317ab938 upstream.

On some CPUs we can prevent a vulnerability related to store-to-load
forwarding by preventing store forwarding between privilege domains,
by inserting a barrier in kernel entry and exit paths.

This is known to be the case on at least Power7, Power8 and Power9
powerpc CPUs.

Barriers must be inserted generally before the first load after moving
to a higher privilege, and after the last store before moving to a
lower privilege, HV and PR privilege transitions must be protected.

Barriers are added as patch sections, with all kernel/hypervisor entry
points patched, and the exit points to lower privilge levels patched
similarly to the RFI flush patching.

Firmware advertisement is not implemented yet, so CPU flush types
are hard coded.

Thanks to Michal Suchánek for bug fixes and review.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michal Suchánek <msuchanek@suse.de>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Fix section mismatch warnings from setup_rfi_flush()

commit 501a78cbc17c329fabf8e9750a1e9ab810c88a0e upstream.

The recent LPM changes to setup_rfi_flush() are causing some section
mismatch warnings because we removed the __init annotation on
setup_rfi_flush():

  The function setup_rfi_flush() references
  the function __init ppc64_bolted_size().
  the function __init memblock_alloc_base().

The references are actually in init_fallback_flush(), but that is
inlined into setup_rfi_flush().

These references are safe because:
 - only pseries calls setup_rfi_flush() at runtime
 - pseries always passes L1D_FLUSH_FALLBACK at boot
 - so the fallback flush area will always be allocated
 - so the check in init_fallback_flush() will always return early:
   /* Only allocate the fallback flush area once (at boot time). */
   if (l1d_flush_fallback_area)
    return;

 - and therefore we won't actually call the freed init routines.

We should rework the code to make it safer by default rather than
relying on the above, but for now as a quick-fix just add a __ref
annotation to squash the warning.

Fixes: abf110f3e1ce ("powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Restore default security feature flags on setup

commit 6232774f1599028a15418179d17f7df47ede770a upstream.

After migration the security feature flags might have changed (e.g.,
destination system with unpatched firmware), but some flags are not
set/clear again in init_cpu_char_feature_flags() because it assumes
the security flags to be the defaults.

Additionally, if the H_GET_CPU_CHARACTERISTICS hypercall fails then
init_cpu_char_feature_flags() does not run again, which potentially
might leave the system in an insecure or sub-optimal configuration.

So, just restore the security feature flags to the defaults assumed
by init_cpu_char_feature_flags() so it can set/clear them correctly,
and to ensure safe settings are in place in case the hypercall fail.

Fixes: f636c14790ea ("powerpc/pseries: Set or clear security feature flags")
Depends-on: 19887d6a28e2 ("powerpc: Move default security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Move default security feature flags

commit e7347a86830f38dc3e40c8f7e28c04412b12a2e7 upstream.

This moves the definition of the default security feature flags
(i.e., enabled by default) closer to the security feature flags.

This can be used to restore current flags to the default flags.

Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Fix clearing of security feature flags

commit 0f9bdfe3c77091e8704d2e510eb7c2c2c6cde524 upstream.

The H_CPU_BEHAV_* flags should be checked for in the 'behaviour' field
of 'struct h_cpu_char_result' -- 'character' is for H_CPU_CHAR_*
flags.

Found by playing around with QEMU's implementation of the hypercall:

  H_CPU_CHAR=0xf000000000000000
  H_CPU_BEHAV=0x0000000000000000

  This clears H_CPU_BEHAV_FAVOUR_SECURITY and H_CPU_BEHAV_L1D_FLUSH_PR
  so pseries_setup_rfi_flush() disables 'rfi_flush'; and it also
  clears H_CPU_CHAR_L1D_THREAD_PRIV flag. So there is no RFI flush
  mitigation at all for cpu_show_meltdown() to report; but currently
  it does:

  Original kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/meltdown
    Mitigation: RFI Flush

  Patched kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/meltdown
    Not affected

  H_CPU_CHAR=0x0000000000000000
  H_CPU_BEHAV=0xf000000000000000

  This sets H_CPU_BEHAV_BNDS_CHK_SPEC_BAR so cpu_show_spectre_v1() should
  report vulnerable; but currently it doesn't:

  Original kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
    Not affected

  Patched kernel:

    # cat /sys/devices/system/cpu/vulnerabilities/spectre_v1
    Vulnerable

Brown-paper-bag-by: Michael Ellerman <mpe@ellerman.id.au>
Fixes: f636c14790ea ("powerpc/pseries: Set or clear security feature flags")
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Wire up cpu_show_spectre_v2()

commit d6fbe1c55c55c6937cbea3531af7da84ab7473c3 upstream.

Add a definition for cpu_show_spectre_v2() to override the generic
version. This has several permuations, though in practice some may not
occur we cater for any combination.

The most verbose is:

  Mitigation: Indirect branch serialisation (kernel only), Indirect
  branch cache disabled, ori31 speculation barrier enabled

We don't treat the ori31 speculation barrier as a mitigation on its
own, because it has to be *used* by code in order to be a mitigation
and we don't know if userspace is doing that. So if that's all we see
we say:

  Vulnerable, ori31 speculation barrier enabled

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Wire up cpu_show_spectre_v1()

commit 56986016cb8cd9050e601831fe89f332b4e3c46e upstream.

Add a definition for cpu_show_spectre_v1() to override the generic
version. Currently this just prints "Not affected" or "Vulnerable"
based on the firmware flag.

Although the kernel does have array_index_nospec() in a few places, we
haven't yet audited all the powerpc code to see where it's necessary,
so for now we don't list that as a mitigation.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Use the security flags in pseries_setup_rfi_flush()

commit 2e4a16161fcd324b1f9bf6cb6856529f7eaf0689 upstream.

Now that we have the security flags we can simplify the code in
pseries_setup_rfi_flush() because the security flags have pessimistic
defaults.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Use the security flags in pnv_setup_rfi_flush()

commit 37c0bdd00d3ae83369ab60a6712c28e11e6458d5 upstream.

Now that we have the security flags we can significantly simplify the
code in pnv_setup_rfi_flush(), because we can use the flags instead of
checking device tree properties and because the security flags have
pessimistic defaults.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Enhance the information in cpu_show_meltdown()

commit ff348355e9c72493947be337bb4fae4fc1a41eba upstream.

Now that we have the security feature flags we can make the
information displayed in the "meltdown" file more informative.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Move cpu_show_meltdown()

commit 8ad33041563a10b34988800c682ada14b2612533 upstream.

This landed in setup_64.c for no good reason other than we had nowhere
else to put it. Now that we have a security-related file, that is a
better place for it so move it.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Set or clear security feature flags

commit 77addf6e95c8689e478d607176b399a6242a777e upstream.

Now that we have feature flags for security related things, set or
clear them based on what we see in the device tree provided by
firmware.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Set or clear security feature flags

commit f636c14790ead6cc22cf62279b1f8d7e11a67116 upstream.

Now that we have feature flags for security related things, set or
clear them based on what we receive from the hypercall.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc: Add security feature flags for Spectre/Meltdown

commit 9a868f634349e62922c226834aa23e3d1329ae7f upstream.

This commit adds security feature flags to reflect the settings we
receive from firmware regarding Spectre/Meltdown mitigations.

The feature names reflect the names we are given by firmware on bare
metal machines. See the hostboot source for details.

Arguably these could be firmware features, but that then requires them
to be read early in boot so they're available prior to asm feature
patching, but we don't actually want to use them for patching. We may
also want to dynamically update them in future, which would be
incompatible with the way firmware features work (at the moment at
least). So for now just make them separate flags.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Add new H_GET_CPU_CHARACTERISTICS flags

commit c4bc36628d7f8b664657d8bd6ad1c44c177880b7 upstream.

Add some additional values which have been defined for the
H_GET_CPU_CHARACTERISTICS hypercall.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Call setup_rfi_flush() after LPM migration

commit 921bc6cf807ceb2ab8005319cf39f33494d6b100 upstream.

We might have migrated to a machine that uses a different flush type,
or doesn't need flushing at all.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Differentiate enabled and patched flush types

commit 0063d61ccfc011f379a31acaeba6de7c926fed2c upstream.

Currently the rfi-flush messages print 'Using <type> flush' for all
enabled_flush_types, but that is not necessarily true -- as now the
fallback flush is always enabled on pseries, but the fixup function
overwrites its nop/branch slot with other flush types, if available.

So, replace the 'Using <type> flush' messages with '<type> flush is
available'.

Also, print the patched flush types in the fixup function, so users
can know what is (not) being used (e.g., the slower, fallback flush,
or no flush type at all if flush is disabled via the debugfs switch).

Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Always enable fallback flush on pseries

commit 84749a58b6e382f109abf1e734bc4dd43c2c25bb upstream.

This ensures the fallback flush area is always allocated on pseries,
so in case a LPAR is migrated from a patched to an unpatched system,
it is possible to enable the fallback flush in the target system.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Make it possible to call setup_rfi_flush() again

commit abf110f3e1cea40f5ea15e85f5d67c39c14568a7 upstream.

For PowerVM migration we want to be able to call setup_rfi_flush()
again after we've migrated the partition.

To support that we need to check that we're not trying to allocate the
fallback flush area after memblock has gone away (i.e., boot-time only).

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/rfi-flush: Move the logic to avoid a redo into the debugfs code

commit 1e2a9fc7496955faacbbed49461d611b704a7505 upstream.

rfi_flush_enable() includes a check to see if we're already
enabled (or disabled), and in that case does nothing.

But that means calling setup_rfi_flush() a 2nd time doesn't actually
work, which is a bit confusing.

Move that check into the debugfs code, where it really belongs.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/powernv: Support firmware disable of RFI flush

commit eb0a2d2620ae431c543963c8c7f08f597366fc60 upstream.

Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.

Fixes: 6e032b350cd1 ("powerpc/powernv: Check device-tree for RFI flush settings")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/pseries: Support firmware disable of RFI flush

commit 582605a429e20ae68fd0b041b2e840af296edd08 upstream.

Some versions of firmware will have a setting that can be configured
to disable the RFI flush, add support for it.

Fixes: 8989d56878a7 ("powerpc/pseries: Query hypervisor for RFI flush settings")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Improve RFI L1-D cache flush fallback

commit bdcb1aefc5b3f7d0f1dc8b02673602bca2ff7a4b upstream.

The fallback RFI flush is used when firmware does not provide a way
to flush the cache. It's a "displacement flush" that evicts useful
data by displacing it with an uninteresting buffer.

The flush has to take care to work with implementation specific cache
replacment policies, so the recipe has been in flux. The initial
slow but conservative approach is to touch all lines of a congruence
class, with dependencies between each load. It has since been
determined that a linear pattern of loads without dependencies is
sufficient, and is significantly faster.

Measuring the speed of a null syscall with RFI fallback flush enabled
gives the relative improvement:

P8 - 1.83x
P9 - 1.75x

The flush also becomes simpler and more adaptable to different cache
geometries.

Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/kvm: fix LAPIC timer drift when guest uses periodic mode

commit d8f2f498d9ed0c5010bc1bbc1146f94c8bf9f8cc upstream.

Since 4.10, commit 8003c9ae204e (KVM: LAPIC: add APIC Timer
periodic/oneshot mode VMX preemption timer support), guests using
periodic LAPIC timers (such as FreeBSD 8.4) would see their timers
drift significantly over time.

Differences in the underlying clocks and numerical errors means the
periods of the two timers (hv and sw) are not the same. This
difference will accumulate with every expiry resulting in a large
error between the hv and sw timer.

This means the sw timer may be running slow when compared to the hv
timer. When the timer is switched from hv to sw, the now active sw
timer will expire late. The guest VCPU is reentered and it switches to
using the hv timer. This timer catches up, injecting multiple IRQs
into the guest (of which the guest only sees one as it does not get to
run until the hv timer has caught up) and thus the guest's timer rate
is low (and becomes increasing slower over time as the sw timer lags
further and further behind).

I believe a similar problem would occur if the hv timer is the slower
one, but I have not observed this.

Fix this by synchronizing the deadlines for both timers to the same
time source on every tick. This prevents the errors from accumulating.

Fixes: 8003c9ae204e21204e49816c5ea629357e283b06
Cc: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: David Vrabel <david.vrabel@nutanix.com>
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kvm: x86: IA32_ARCH_CAPABILITIES is always supported

commit 1eaafe91a0df4157521b6417b3dd8430bf5f52f0 upstream.

If there is a possibility that a VM may migrate to a Skylake host,
then the hypervisor should report IA32_ARCH_CAPABILITIES.RSBA[bit 2]
as being set (future work, of course). This implies that
CPUID.(EAX=7,ECX=0):EDX.ARCH_CAPABILITIES[bit 29] should be
set. Therefore, kvm should report this CPUID bit as being supported
whether or not the host supports it.  Userspace is still free to clear
the bit if it chooses.

For more information on RSBA, see Intel's white paper, "Retpoline: A
Branch Target Injection Mitigation" (Document Number 337131-001),
currently available at https://bugzilla.kernel.org/show_bug.cgi?id=199511.

Since the IA32_ARCH_CAPABILITIES MSR is emulated in kvm, there is no
dependency on hardware support for this feature.

Signed-off-by: Jim Mattson <jmattson@google.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Fixes: 28c1c9fabf48 ("KVM/VMX: Emulate MSR_IA32_ARCH_CAPABILITIES")
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: x86: Update cpuid properly when CR4.OSXAVE or CR4.PKE is changed

commit c4d2188206bafa177ea58e9a25b952baa0bf7712 upstream.

The CPUID bits of OSXSAVE (function=0x1) and OSPKE (func=0x7, leaf=0x0)
allows user apps to detect if OS has set CR4.OSXSAVE or CR4.PKE. KVM is
supposed to update these CPUID bits when CR4 is updated. Current KVM
code doesn't handle some special cases when updates come from emulator.
Here is one example:

  Step 1: guest boots
  Step 2: guest OS enables XSAVE ==> CR4.OSXSAVE=1 and CPUID.OSXSAVE=1
  Step 3: guest hot reboot ==> QEMU reset CR4 to 0, but CPUID.OSXAVE==1
  Step 4: guest os checks CPUID.OSXAVE, detects 1, then executes xgetbv

Step 4 above will cause an #UD and guest crash because guest OS hasn't
turned on OSXAVE yet. This patch solves the problem by comparing the the
old_cr4 with cr4. If the related bits have been changed,
kvm_update_cpuid() needs to be called.

Signed-off-by: Wei Huang <wei@redhat.com>
Reviewed-by: Bandan Das <bsd@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: s390: vsie: fix < 8k check for the itdba

commit f4a551b72358facbbe5714248dff78404272feee upstream.

By missing an "L", we might detect some addresses to be <8k,
although they are not.

e.g. for itdba = 100001fff
!(gpa & ~0x1fffU) -> 1
!(gpa & ~0x1fffUL) -> 0

So we would report a SIE validity intercept although everything is fine.

Fixes: 166ecb3 ("KVM: s390: vsie: support transactional execution")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM/VMX: Expose SSBD properly to guests

commit 0aa48468d00959c8a37cd3ac727284f4f7359151 upstream.

The X86_FEATURE_SSBD is an synthetic CPU feature - that is
it bit location has no relevance to the real CPUID 0x7.EBX[31]
bit position. For that we need the new CPU feature name.

Fixes: 52817587e706 ("x86/cpufeatures: Disentangle SSBD enumeration")
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: stable@vger.kernel.org
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Link: https://lkml.kernel.org/r/20180521215449.26423-2-konrad.wilk@oracle.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/sys.c: fix potential Spectre v1 issue

commit 23d6aef74da86a33fa6bb75f79565e0a16ee97c2 upstream.

`resource' can be controlled by user-space, hence leading to a potential
exploitation of the Spectre variant 1 vulnerability.

This issue was detected with the help of Smatch:

  kernel/sys.c:1474 __do_compat_sys_old_getrlimit() warn: potential spectre issue 'get_current()->signal->rlim' (local cap)
  kernel/sys.c:1455 __do_sys_old_getrlimit() warn: potential spectre issue 'get_current()->signal->rlim' (local cap)

Fix this by sanitizing *resource* before using it to index
current->signal->rlim

Notice that given that speculation windows are large, the policy is to
kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].

[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2

Link: http://lkml.kernel.org/r/20180515030038.GA11822@embeddedor.com
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kasan: fix memory hotplug during boot

commit 3f1959721558a976aaf9c2024d5bc884e6411bf7 upstream.

Using module_init() is wrong.  E.g.  ACPI adds and onlines memory before
our memory notifier gets registered.

This makes sure that ACPI memory detected during boot up will not result
in a kernel crash.

Easily reproducible with QEMU, just specify a DIMM when starting up.

Link: http://lkml.kernel.org/r/20180522100756.18478-3-david@redhat.com
Fixes: 786a8959912e ("kasan: disable memory hotplug")
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kasan: free allocated shadow memory on MEM_CANCEL_ONLINE

commit ed1596f9ab958dd156a66c9ff1029d3761c1786a upstream.

We have to free memory again when we cancel onlining, otherwise a later
onlining attempt will fail.

Link: http://lkml.kernel.org/r/20180522100756.18478-2-david@redhat.com
Fixes: fa69b5989bb0 ("mm/kasan: add support for memory hotplug")
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mm/kasan: don't vfree() nonexistent vm_area

commit 0f901dcbc31f88ae41a2aaa365f7802b5d520a28 upstream.

KASAN uses different routines to map shadow for hot added memory and
memory obtained in boot process.  Attempt to offline memory onlined by
normal boot process leads to this:

    Trying to vfree() nonexistent vm area (000000005d3b34b9)
    WARNING: CPU: 2 PID: 13215 at mm/vmalloc.c:1525 __vunmap+0x147/0x190

    Call Trace:
     kasan_mem_notifier+0xad/0xb9
     notifier_call_chain+0x166/0x260
     __blocking_notifier_call_chain+0xdb/0x140
     __offline_pages+0x96a/0xb10
     memory_subsys_offline+0x76/0xc0
     device_offline+0xb8/0x120
     store_mem_state+0xfa/0x120
     kernfs_fop_write+0x1d5/0x320
     __vfs_write+0xd4/0x530
     vfs_write+0x105/0x340
     SyS_write+0xb0/0x140

Obviously we can't call vfree() to free memory that wasn't allocated via
vmalloc().  Use find_vm_area() to see if we can call vfree().

Unfortunately it's a bit tricky to properly unmap and free shadow
allocated during boot, so we'll have to keep it.  If memory will come
online again that shadow will be reused.

Matthew asked: how can you call vfree() on something that isn't a
vmalloc address?

  vfree() is able to free any address returned by
  __vmalloc_node_range().  And __vmalloc_node_range() gives you any
  address you ask.  It doesn't have to be an address in [VMALLOC_START,
  VMALLOC_END] range.

  That's also how the module_alloc()/module_memfree() works on
  architectures that have designated area for modules.

[aryabinin@virtuozzo.com: improve comments]
Link: http://lkml.kernel.org/r/dabee6ab-3a7a-51cd-3b86-5468718e0390@virtuozzo.com
[akpm@linux-foundation.org: fix typos, reflow comment]
Link: http://lkml.kernel.org/r/20180201163349.8700-1-aryabinin@virtuozzo.com
Fixes: fa69b5989bb0 ("mm/kasan: add support for memory hotplug")
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reported-by: Paul Menzel <pmenzel+linux-kasan-dev@molgen.mpg.de>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipc/shm: fix shmat() nil address after round-down when remapping

commit 8f89c007b6dec16a1793cb88de88fcc02117bbbc upstream.

shmat()'s SHM_REMAP option forbids passing a nil address for; this is in
fact the very first thing we check for.  Andrea reported that for
SHM_RND|SHM_REMAP cases we can end up bypassing the initial addr check,
but we need to check again if the address was rounded down to nil.  As
of this patch, such cases will return -EINVAL.

Link: http://lkml.kernel.org/r/20180503204934.kk63josdu6u53fbd@linux-n805
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Joe Lawrence <joe.lawrence@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Revert "ipc/shm: Fix shmat mmap nil-page protection"

commit a73ab244f0dad8fffb3291b905f73e2d3eaa7c00 upstream.

Patch series "ipc/shm: shmat() fixes around nil-page".

These patches fix two issues reported[1] a while back by Joe and Andrea
around how shmat(2) behaves with nil-page.

The first reverts a commit that it was incorrectly thought that mapping
nil-page (address=0) was a no no with MAP_FIXED.  This is not the case,
with the exception of SHM_REMAP; which is address in the second patch.

I chose two patches because it is easier to backport and it explicitly
reverts bogus behaviour.  Both patches ought to be in -stable and ltp
testcases need updated (the added testcase around the cve can be
modified to just test for SHM_RND|SHM_REMAP).

[1] lkml.kernel.org/r/20180430172152.nfa564pvgpk3ut7p@linux-n805

This patch (of 2):

Commit 95e91b831f87 ("ipc/shm: Fix shmat mmap nil-page protection")
worked on the idea that we should not be mapping as root addr=0 and
MAP_FIXED.  However, it was reported that this scenario is in fact
valid, thus making the patch both bogus and breaks userspace as well.

For example X11's libint10.so relies on shmat(1, SHM_RND) for lowmem
initialization[1].

[1] https://cgit.freedesktop.org/xorg/xserver/tree/hw/xfree86/os-support/linux/int10/linux.c#n347
Link: http://lkml.kernel.org/r/20180503203243.15045-2-dave@stgolabs.net
Fixes: 95e91b831f87 ("ipc/shm: Fix shmat mmap nil-page protection")
Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Reported-by: Joe Lawrence <joe.lawrence@redhat.com>
Reported-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: Manfred Spraul <manfred@colorfullife.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

idr: fix invalid ptr dereference on item delete

commit 7a4deea1aa8bddfed4ef1b35fc2b6732563d8ad5 upstream.

If the radix tree underlying the IDR happens to be full and we attempt
to remove an id which is larger than any id in the IDR, we will call
__radix_tree_delete() with an uninitialised 'slot' pointer, at which
point anything could happen.  This was easiest to hit with a single
entry at id 0 and attempting to remove a non-0 id, but it could have
happened with 64 entries and attempting to remove an id >= 64.

Roman said:

  The syzcaller test boils down to opening /dev/kvm, creating an
  eventfd, and calling a couple of KVM ioctls. None of this requires
  superuser. And the result is dereferencing an uninitialized pointer
  which is likely a crash. The specific path caught by syzbot is via
  KVM_HYPERV_EVENTD ioctl which is new in 4.17. But I guess there are
  other user-triggerable paths, so cc:stable is probably justified.

Matthew added:

  We have around 250 calls to idr_remove() in the kernel today. Many of
  them pass an ID which is embedded in the object they're removing, so
  they're safe. Picking a few likely candidates:

  drivers/firewire/core-cdev.c looks unsafe; the ID comes from an ioctl.
  drivers/gpu/drm/amd/amdgpu/amdgpu_ctx.c is similar
  drivers/atm/nicstar.c could be taken down by a handcrafted packet

Link: http://lkml.kernel.org/r/20180518175025.GD6361@bombadil.infradead.org
Fixes: 0a835c4f090a ("Reimplement IDR and IDA using the radix tree")
Reported-by: <syzbot+35666cba7f0a337e2e79@syzkaller.appspotmail.com>
Debugged-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Matthew Wilcox <mawilcox@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sr: pass down correctly sized SCSI sense buffer

commit f7068114d45ec55996b9040e98111afa56e010fe upstream.

We're casting the CDROM layer request_sense to the SCSI sense
buffer, but the former is 64 bytes and the latter is 96 bytes.
As we generally allocate these on the stack, we end up blowing
up the stack.

Fix this by wrapping the scsi_execute() call with a properly
sized sense buffer, and copying back the bits for the CDROM
layer.

Cc: stable@vger.kernel.org
Reported-by: Piotr Gabriel Kosinski <pg.kosinski@gmail.com>
Reported-by: Daniel Shapira <daniel@twistlock.com>
Tested-by: Kees Cook <keescook@chromium.org>
Fixes: 82ed4db499b8 ("block: split scsi_request out of struct request")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/umem: Use the correct mm during ib_umem_release

commit 8e907ed4882714fd13cfe670681fc6cb5284c780 upstream.

User-space may invoke ibv_reg_mr and ibv_dereg_mr in different threads.

If ibv_dereg_mr is called after the thread which invoked ibv_reg_mr has
exited, get_pid_task will return NULL and ib_umem_release will not
decrease mm->pinned_vm.

Instead of using threads to locate the mm, use the overall tgid from the
ib_ucontext struct instead. This matches the behavior of ODP and
disassociate in handling the mm of the process that called ibv_reg_mr.

Cc: <stable@vger.kernel.org>
Fixes: 87773dd56d54 ("IB: ib_umem_release() should decrement mm->pinned_vm from ib_umem_get")
Signed-off-by: Lidong Chen <lidongchen@tencent.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/hfi1: Use after free race condition in send context error path

commit f9e76ca3771bf23d2142a81a88ddd8f31f5c4c03 upstream.

A pio send egress error can occur when the PSM library attempts to
to send a bad packet.  That issue is still being investigated.

The pio error interrupt handler then attempts to progress the recovery
of the errored pio send context.

Code inspection reveals that the handling lacks the necessary locking
if that recovery interleaves with a PSM close of the "context" object
contains the pio send context.

The lack of the locking can cause the recovery to access the already
freed pio send context object and incorrectly deduce that the pio
send context is actually a kernel pio send context as shown by the
NULL deref stack below:

[<ffffffff8143d78c>] _dev_info+0x6c/0x90
[<ffffffffc0613230>] sc_restart+0x70/0x1f0 [hfi1]
[<ffffffff816ab124>] ? __schedule+0x424/0x9b0
[<ffffffffc06133c5>] sc_halted+0x15/0x20 [hfi1]
[<ffffffff810aa3ba>] process_one_work+0x17a/0x440
[<ffffffff810ab086>] worker_thread+0x126/0x3c0
[<ffffffff810aaf60>] ? manage_workers.isra.24+0x2a0/0x2a0
[<ffffffff810b252f>] kthread+0xcf/0xe0
[<ffffffff810b2460>] ? insert_kthread_work+0x40/0x40
[<ffffffff816b8798>] ret_from_fork+0x58/0x90
[<ffffffff810b2460>] ? insert_kthread_work+0x40/0x40

This is the best case scenario and other scenarios can corrupt the
already freed memory.

Fix by adding the necessary locking in the pio send context error
handler.

Cc: <stable@vger.kernel.org> # 4.9.x
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/64s: Clear PCR on boot

commit faf37c44a105f3608115785f17cbbf3500f8bc71 upstream.

Clear the PCR (Processor Compatibility Register) on boot to ensure we
are not running in a compatibility mode.

We've seen this cause problems when a crash (and kdump) occurs while
running compat mode guests. The kdump kernel then runs with the PCR
set and causes problems. The symptom in the kdump kernel (also seen in
petitboot after fast-reboot) is early userspace programs taking
sigills on newer instructions (seen in libc).

Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: lse: Add early clobbers to some input/output asm operands

commit 32c3fa7cdf0c4a3eb8405fc3e13398de019e828b upstream.

For LSE atomics that read and write a register operand, we need to
ensure that these operands are annotated as "early clobber" if the
register is written before all of the input operands have been consumed.
Failure to do so can result in the compiler allocating the same register
to both operands, leading to splats such as:

 Unable to handle kernel paging request at virtual address 11111122222221
 [...]
 x1 : 1111111122222222 x0 : 1111111122222221
 Process swapper/0 (pid: 1, stack limit = 0x000000008209f908)
 Call trace:
  test_atomic64+0x1360/0x155c

where x0 has been allocated as both the value to be stored and also the
atomic_t pointer.

This patch adds the missing clobbers.

Cc: <stable@vger.kernel.org>
Cc: Dave Martin <dave.martin@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Reported-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/vmwgfx: Fix 32-bit VMW_PORT_HB_[IN|OUT] macros

commit 938ae7259c908ad031da35d551da297640bb640c upstream.

Depending on whether the kernel is compiled with frame-pointer or not,
the temporary memory location used for the bp parameter in these macros
is referenced relative to the stack pointer or the frame pointer.
Hence we can never reference that parameter when we've modified either
the stack pointer or the frame pointer, because then the compiler would
generate an incorrect stack reference.

Fix this by pushing the temporary memory parameter on a known location on
the stack before modifying the stack- and frame pointers.

Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Brian Paul <brianp@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen-swiotlb: fix the check condition for xen_swiotlb_free_coherent

commit 4855c92dbb7b3b85c23e88ab7ca04f99b9677b41 upstream.

When run raidconfig from Dom0 we found that the Xen DMA heap is reduced,
but Dom Heap is increased by the same size. Tracing raidconfig we found
that the related ioctl() in megaraid_sas will call dma_alloc_coherent()
to apply memory. If the memory allocated by Dom0 is not in the DMA area,
it will exchange memory with Xen to meet the requiment. Later drivers
call dma_free_coherent() to free the memory, on xen_swiotlb_free_coherent()
the check condition (dev_addr + size - 1 <= dma_mask) is always false,
it prevents calling xen_destroy_contiguous_region() to return the memory
to the Xen DMA heap.

This issue introduced by commit 6810df88dcfc2 "xen-swiotlb: When doing
coherent alloc/dealloc check before swizzling the MFNs.".

Signed-off-by: Joe Jin <joe.jin@oracle.com>
Tested-by: John Sobecki <john.sobecki@oracle.com>
Reviewed-by: Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: blacklist Micron 500IT SSD with MU01 firmware

commit 136d769e0b3475d71350aa3648a116a6ee7a8f6c upstream.

While whitelisting Micron M500DC drives, the tweaked blacklist entry
enabled queued TRIM from M500IT variants also. But these do not support
queued TRIM. And while using those SSDs with the latest kernel we have
seen errors and even the partition table getting corrupted.

Some part from the dmesg:
[    6.727384] ata1.00: ATA-9: Micron_M500IT_MTFDDAK060MBD, MU01, max UDMA/133
[    6.727390] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[    6.741026] ata1.00: supports DRM functions and may not be fully accessible
[    6.759887] ata1.00: configured for UDMA/133
[    6.762256] scsi 0:0:0:0: Direct-Access     ATA      Micron_M500IT_MT MU01 PQ: 0 ANSI: 5

and then for the error:
[  120.860334] ata1.00: exception Emask 0x1 SAct 0x7ffc0007 SErr 0x0 action 0x6 frozen
[  120.860338] ata1.00: irq_stat 0x40000008
[  120.860342] ata1.00: failed command: SEND FPDMA QUEUED
[  120.860351] ata1.00: cmd 64/01:00:00:00:00/00:00:00:00:00/a0 tag 0 ncq dma 512 out
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[  120.860353] ata1.00: status: { DRDY }
[  120.860543] ata1: hard resetting link
[  121.166128] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  121.166376] ata1.00: supports DRM functions and may not be fully accessible
[  121.186238] ata1.00: supports DRM functions and may not be fully accessible
[  121.204445] ata1.00: configured for UDMA/133
[  121.204454] ata1.00: device reported invalid CHS sector 0
[  121.204541] sd 0:0:0:0: [sda] tag#18 UNKNOWN(0x2003) Result: hostbyte=0x00 driverbyte=0x08
[  121.204546] sd 0:0:0:0: [sda] tag#18 Sense Key : 0x5 [current]
[  121.204550] sd 0:0:0:0: [sda] tag#18 ASC=0x21 ASCQ=0x4
[  121.204555] sd 0:0:0:0: [sda] tag#18 CDB: opcode=0x93 93 08 00 00 00 00 00 04 28 80 00 00 00 30 00 00
[  121.204559] print_req_error: I/O error, dev sda, sector 272512

After few reboots with these errors, and the SSD is corrupted.
After blacklisting it, the errors are not seen and the SSD does not get
corrupted any more.

Fixes: 243918be6393 ("libata: Do not blacklist Micron M500DC")
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: Blacklist some Sandisk SSDs for NCQ

commit 322579dcc865b94b47345ad1b6002ad167f85405 upstream.

Sandisk SSDs SD7SN6S256G and SD8SN8U256G are regularly locking up
regularly under sustained moderate load with NCQ enabled.  Blacklist
for now.

Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-iproc: add SDHCI_QUIRK2_HOST_OFF_CARD_ON for cygnus

commit 3de06d5a1f05c11c94cbb68af14dbfa7fb81d78b upstream.

The SDHCI_QUIRK2_HOST_OFF_CARD_ON is needed for the driver to
properly reset the host controller (reset all) on initialization
after exiting deep sleep.

Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Fixes: c833e92bbb60 ("mmc: sdhci-iproc: support standard byte register accesses")
Cc: stable@vger.kernel.org # v4.10+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-iproc: fix 32bit writes for TRANSFER_MODE register

commit 5f651b870485ee60f5abbbd85195a6852978894a upstream.

When the host controller accepts only 32bit writes, the value of the
16bit TRANSFER_MODE register, that has the same 32bit address as the
16bit COMMAND register, needs to be saved and it will be written
in a 32bit write together with the command as this will trigger the
host to send the command on the SD interface.
When sending the tuning command, TRANSFER_MODE is written and then
sdhci_set_transfer_mode reads it back to clear AUTO_CMD12 bit and
write it again resulting in wrong value to be written because the
initial write value was saved in a shadow and the read-back returned
a wrong value, from the register.
Fix sdhci_iproc_readw to return the saved value of TRANSFER_MODE
when a saved value exist.
Same fix for read of BLOCK_SIZE and BLOCK_COUNT registers, that are
saved for a different reason, although a scenario that will cause the
mentioned problem on this registers is not probable.

Fixes: b580c52d58d9 ("mmc: sdhci-iproc: add IPROC SDHCI driver")
Signed-off-by: Corneliu Doban <corneliu.doban@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mmc: sdhci-iproc: remove hard coded mmc cap 1.8v

commit 4c94238f37af87a2165c3fb491b4a8b50e90649c upstream.

Remove hard coded mmc cap 1.8v from platform data as it is board specific.
The 1.8v DDR mmc caps can be enabled using DTS property for those
boards that support it.

Fixes: b17b4ab8ce38 ("mmc: sdhci-iproc: define MMC caps in platform data")
Signed-off-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

do d_instantiate/unlock_new_inode combinations safely

commit 1e2e547a93a00ebc21582c06ca3c6cfea2a309ee upstream.

For anything NFS-exported we do _not_ want to unlock new inode
before it has grown an alias; original set of fixes got the
ordering right, but missed the nasty complication in case of
lockdep being enabled - unlock_new_inode() does
lockdep_annotate_inode_mutex_key(inode)
which can only be done before anyone gets a chance to touch
->i_mutex.  Unfortunately, flipping the order and doing
unlock_new_inode() before d_instantiate() opens a window when
mkdir can race with open-by-fhandle on a guessed fhandle, leading
to multiple aliases for a directory inode and all the breakage
that follows from that.

Correct solution: a new primitive (d_instantiate_new())
combining these two in the right order - lockdep annotate, then
d_instantiate(), then the rest of unlock_new_inode().  All
combinations of d_instantiate() with unlock_new_inode() should
be converted to that.

Cc: stable@kernel.org # 2.6.29 and later
Tested-by: Mike Marshall <hubcap@omnibond.com>
Reviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ALSA: timer: Fix pause event notification

commit 3ae180972564846e6d794e3615e1ab0a1e6c4ef9 upstream.

Commit f65e0d299807 ("ALSA: timer: Call notifier in the same spinlock")
combined the start/continue and stop/pause functions, and in doing so
changed the event code for the pause case to SNDRV_TIMER_EVENT_CONTINUE.
Change it back to SNDRV_TIMER_EVENT_PAUSE.

Fixes: f65e0d299807 ("ALSA: timer: Call notifier in the same spinlock")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aio: fix io_destroy(2) vs. lookup_ioctx() race

commit baf10564fbb66ea222cae66fbff11c444590ffd9 upstream.

kill_ioctx() used to have an explicit RCU delay between removing the
reference from ->ioctx_table and percpu_ref_kill() dropping the refcount.
At some point that delay had been removed, on the theory that
percpu_ref_kill() itself contained an RCU delay.  Unfortunately, that was
the wrong kind of RCU delay and it didn't care about rcu_read_lock() used
by lookup_ioctx().  As the result, we could get ctx freed right under
lookup_ioctx().  Tejun has fixed that in a6d7cff472e ("fs/aio: Add explicit
RCU grace period when freeing kioctx"); however, that fix is not enough.

Suppose io_destroy() from one thread races with e.g. io_setup() from another;
CPU1 removes the reference from current->mm->ioctx_table[...] just as CPU2
has picked it (under rcu_read_lock()).  Then CPU1 proceeds to drop the
refcount, getting it to 0 and triggering a call of free_ioctx_users(),
which proceeds to drop the secondary refcount and once that reaches zero
calls free_ioctx_reqs().  That does
        INIT_RCU_WORK(&ctx->free_rwork, free_ioctx);
        queue_rcu_work(system_wq, &ctx->free_rwork);
and schedules freeing the whole thing after RCU delay.

In the meanwhile CPU2 has gotten around to percpu_ref_get(), bumping the
refcount from 0 to 1 and returned the reference to io_setup().

Tejun's fix (that queue_rcu_work() in there) guarantees that ctx won't get
freed until after percpu_ref_get().  Sure, we'd increment the counter before
ctx can be freed.  Now we are out of rcu_read_lock() and there's nothing to
stop freeing of the whole thing.  Unfortunately, CPU2 assumes that since it
has grabbed the reference, ctx is *NOT* going away until it gets around to
dropping that reference.

The fix is obvious - use percpu_ref_tryget_live() and treat failure as miss.
It's not costlier than what we currently do in normal case, it's safe to
call since freeing *is* delayed and it closes the race window - either
lookup_ioctx() comes before percpu_ref_kill() (in which case ctx->users
won't reach 0 until the caller of lookup_ioctx() drops it) or lookup_ioctx()
fails, ctx->users is unaffected and caller of lookup_ioctx() doesn't see
the object in question at all.

Cc: stable@kernel.org
Fixes: a6d7cff472e "fs/aio: Add explicit RCU grace period when freeing kioctx"
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: don't scan the inode cache before SB_BORN is set

commit 79f546a696bff2590169fb5684e23d65f4d9f591 upstream.

We recently had an oops reported on a 4.14 kernel in
xfs_reclaim_inodes_count() where sb->s_fs_info pointed to garbage
and so the m_perag_tree lookup walked into lala land.  It produces
an oops down this path during the failed mount:

  radix_tree_gang_lookup_tag+0xc4/0x130
  xfs_perag_get_tag+0x37/0xf0
  xfs_reclaim_inodes_count+0x32/0x40
  xfs_fs_nr_cached_objects+0x11/0x20
  super_cache_count+0x35/0xc0
  shrink_slab.part.66+0xb1/0x370
  shrink_node+0x7e/0x1a0
  try_to_free_pages+0x199/0x470
  __alloc_pages_slowpath+0x3a1/0xd20
  __alloc_pages_nodemask+0x1c3/0x200
  cache_grow_begin+0x20b/0x2e0
  fallback_alloc+0x160/0x200
  kmem_cache_alloc+0x111/0x4e0

The problem is that the superblock shrinker is running before the
filesystem structures it depends on have been fully set up. i.e.
the shrinker is registered in sget(), before ->fill_super() has been
called, and the shrinker can call into the filesystem before
fill_super() does it's setup work. Essentially we are exposed to
both use-after-free and use-before-initialisation bugs here.

To fix this, add a check for the SB_BORN flag in super_cache_count.
In general, this flag is not set until ->fs_mount() completes
successfully, so we know that it is set after the filesystem
setup has completed. This matches the trylock_super() behaviour
which will not let super_cache_scan() run if SB_BORN is not set, and
hence will not allow the superblock shrinker from entering the
filesystem while it is being set up or after it has failed setup
and is being torn down.

Cc: stable@kernel.org
Signed-Off-By: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

affs_lookup(): close a race with affs_remove_link()

commit 30da870ce4a4e007c901858a96e9e394a1daa74a upstream.

we unlock the directory hash too early - if we are looking at secondary
link and primary (in another directory) gets removed just as we unlock,
we could have the old primary moved in place of the secondary, leaving
us to look into freed entry (and leaving our dentry with ->d_fsdata
pointing to a freed entry).

Cc: stable@vger.kernel.org # 2.4.4+
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: Fix spelling mistake: "cop_unsuable" -> "cop_unusable"

commit ba3696e94d9d590d9a7e55f68e81c25dba515191 upstream.

Trivial fix to spelling mistake in debugfs_entries text.

Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kernel-janitors@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: Fix ptrace(2) PTRACE_PEEKUSR and PTRACE_POKEUSR accesses to o32 FGRs

commit 9a3a92ccfe3620743d4ae57c987dc8e9c5f88996 upstream.

Check the TIF_32BIT_FPREGS task setting of the tracee rather than the
tracer in determining the layout of floating-point general registers in
the floating-point context, correcting access to odd-numbered registers
for o32 tracees where the setting disagrees between the two processes.

Fixes: 597ce1723e0f ("MIPS: Support for 64-bit FP with O32 binaries")
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.14+
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: ptrace: Expose FIR register through FP regset

commit 71e909c0cdad28a1df1fa14442929e68615dee45 upstream.

Correct commit 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
and expose the FIR register using the unused 4 bytes at the end of the
NT_PRFPREG regset.  Without that register included clients cannot use
the PTRACE_GETREGSET request to retrieve the complete FPU register set
and have to resort to one of the older interfaces, either PTRACE_PEEKUSR
or PTRACE_GETFPREGS, to retrieve the missing piece of data.  Also the
register is irreversibly missing from core dumps.

This register is architecturally hardwired and read-only so the write
path does not matter.  Ignore data supplied on writes then.

Fixes: 7aeb753b5353 ("MIPS: Implement task_user_regset_view.")
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Maciej W. Rozycki <macro@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 3.13+
Patchwork: https://patchwork.linux-mips.org/patch/19273/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

MIPS: c-r4k: Fix data corruption related to cache coherence

commit 55a2aa08b3af519a9693f99cdf7fa6d8b62d9f65 upstream.

When DMA will be performed to a MIPS32 1004K CPS, the L1-cache for the
range needs to be flushed and invalidated first.
The code currently takes one of two approaches.
1/ If the range is less than the size of the dcache, then HIT type
   requests flush/invalidate cache lines for the particular addresses.
   HIT-type requests a globalised by the CPS so this is safe on SMP.

2/ If the range is larger than the size of dcache, then INDEX type
   requests flush/invalidate the whole cache. INDEX type requests affect
   the local cache only. CPS does not propagate them in any way. So this
   invalidation is not safe on SMP CPS systems.

Data corruption due to '2' can quite easily be demonstrated by
repeatedly "echo 3 > /proc/sys/vm/drop_caches" and then sha1sum a file
that is several times the size of available memory. Dropping caches
means that large contiguous extents (large than dcache) are more likely.

This was not a problem before Linux-4.8 because option 2 was never used
if CONFIG_MIPS_CPS was defined. The commit which removed that apparently
didn't appreciate the full consequence of the change.

We could, in theory, globalize the INDEX based flush by sending an IPI
to other cores. These cache invalidation routines can be called with
interrupts disabled and synchronous IPI require interrupts to be
enabled. Asynchronous IPI may not trigger writeback soon enough. So we
cannot use IPI in practice.

We can already test if IPI would be needed for an INDEX operation with
r4k_op_needs_ipi(R4K_INDEX). If this is true then we mustn't try the
INDEX approach as we cannot use IPI. If this is false (e.g. when there
is only one core and hence one L1 cache) then it is safe to use the
INDEX approach without IPI.

This patch avoids options 2 if r4k_op_needs_ipi(R4K_INDEX), and so
eliminates the corruption.

Fixes: c00ab4896ed5 ("MIPS: Remove cpu_has_safe_index_cacheops")
Signed-off-by: NeilBrown <neil@brown.name>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.8+
Patchwork: https://patchwork.linux-mips.org/patch/19259/
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Linux 4.14.44

rtc: goldfish: Add missing MODULE_LICENSE

[ Upstream commit 82d632b85eb89f97051530f556cb49ee1c04bde7 ]

Fix the following warning in MIPS allmodconfig by adding a
MODULE_LICENSE() at the end of rtc-goldfish.c, based on the file header
comment which says GNU General Public License version 2:

WARNING: modpost: missing MODULE_LICENSE() in drivers/rtc/rtc-goldfish.o

Fixes: f22d9cdcb5eb ("rtc: goldfish: Add RTC driver for Android emulator")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Miodrag Dinic <miodrag.dinic@mips.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: linux-rtc@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: rp5c01: fix possible race condition

[ Upstream commit bcdd559268039d8340d38fa58668393596e29fdc ]

The probe function is not allowed to fail after registering the RTC because
the following may happen:

CPU0:                                CPU1:
sys_load_module()
 do_init_module()
  do_one_initcall()
   cmos_do_probe()
    rtc_device_register()
     __register_chrdev()
     cdev->owner = struct module*
                                     open("/dev/rtc0")
    rtc_device_unregister()
  module_put()
  free_module()
   module_free(mod->module_core)
   /* struct module *module is now
      freed */
                                      chrdev_open()
                                       spin_lock(cdev_lock)
                                       cdev_get()
                                        try_module_get()
                                         module_is_live()
                                         /* dereferences already
                                            freed struct module* */

Switch to devm_rtc_allocate_device/rtc_register_device to register the rtc
as late as possible.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: tx4939: avoid unintended sign extension on a 24 bit shift

[ Upstream commit 347876ad47b9923ce26e686173bbf46581802ffa ]

The shifting of buf[5] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. If
the top bit of buf[5] is set then all then all the upper bits sec
end up as also being set because of the sign-extension. Fix this by
casting buf[5] to an unsigned long before the shift.

Detected by CoverityScan, CID#1465292 ("Unintended sign extension")

Fixes: 0e1492330cd2 ("rtc: add rtc-tx4939 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rtc: m41t80: fix race conditions

[ Upstream commit 10d0c768cc6d581523d673b9d1b54213f8a5eb24 ]

The IRQ is requested before the struct rtc is allocated and registered, but
this struct is used in the IRQ handler, leading to:

Unable to handle kernel NULL pointer dereference at virtual address 0000017c
pgd = a38a2f9b
[0000017c] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in:
CPU: 0 PID: 613 Comm: irq/48-m41t80 Not tainted 4.16.0-rc1+ #42
Hardware name: Atmel SAMA5
PC is at mutex_lock+0x14/0x38
LR is at m41t80_handle_irq+0x1c/0x9c
pc : [<c06e864c>]    lr : [<c04b70f0>]    psr: 20000013
sp : dec73f30  ip : 00000000  fp : dec56d98
r10: df437cf0  r9 : c0a03008  r8 : c0145ffc
r7 : df5c4300  r6 : dec568d0  r5 : df593000  r4 : 0000017c
r3 : df592800  r2 : 60000013  r1 : df593000  r0 : 0000017c
Flags: nzCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment none
Control: 10c53c7d  Table: 20004059  DAC: 00000051
Process irq/48-m41t80 (pid: 613, stack limit = 0xb52d091e)
Stack: (0xdec73f30 to 0xdec74000)
3f20:                                     dec56840 df5c4300 00000001 df5c4300
3f40: c0145ffc c0146018 dec56840 ffffe000 00000001 c0146290 dec567c0 00000000
3f60: c0146084 ed7c9a62 c014615c dec56d80 dec567c0 00000000 dec72000 dec56840
3f80: c014615c c012ffc0 dec72000 dec567c0 c012fe80 00000000 00000000 00000000
3fa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 29282726 2d2c2b2a
[<c06e864c>] (mutex_lock) from [<c04b70f0>] (m41t80_handle_irq+0x1c/0x9c)
[<c04b70f0>] (m41t80_handle_irq) from [<c0146018>] (irq_thread_fn+0x1c/0x54)
[<c0146018>] (irq_thread_fn) from [<c0146290>] (irq_thread+0x134/0x1c0)
[<c0146290>] (irq_thread) from [<c012ffc0>] (kthread+0x140/0x148)
[<c012ffc0>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xdec73fb0 to 0xdec73ff8)
3fa0:                                     00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
Code: e3c33d7f e3c3303f f5d0f000 e593300c (e1901f9f)
---[ end trace 22b027302eb7c604 ]---
genirq: exiting task "irq/48-m41t80" (613) is an active IRQ thread (irq 48)

Also, there is another possible race condition. The probe function is not
allowed to fail after the RTC is registered because the following may
happen:

CPU0:                                CPU1:
sys_load_module()
 do_init_module()
  do_one_initcall()
   cmos_do_probe()
    rtc_device_register()
     __register_chrdev()
     cdev->owner = struct module*
                                     open("/dev/rtc0")
    rtc_device_unregister()
  module_put()
  free_module()
   module_free(mod->module_core)
   /* struct module *module is now
      freed */
                                      chrdev_open()
                                       spin_lock(cdev_lock)
                                       cdev_get()
                                        try_module_get()
                                         module_is_live()
                                         /* dereferences already
                                            freed struct module* */

Switch to devm_rtc_allocate_device/rtc_register_device to allocate the rtc
before requesting the IRQ and register it as late as possible.

Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>