drm/i915/dp: Fix eDP max rate for display 11+

intel_dp_set_source_rates() calls intel_dp_is_edp(), which is unsafe to
use before intel_encoder->type is set. This causes incorrect max source
rate to be used for display 11+. On EHL and JSL, HBR3 is used instead of
HBR2, and on the other affected platforms, HBR2 is used instead of HBR3.

Move intel_dp_set_source_rates() to after intel_encoder->type is
set. Add comment to intel_dp_is_edp() describing unsafe usages. Cleanup
intel_dp_init_connector() while at it.

Note: The same change was originally added as commit 680c45c767f6
("drm/i915/dp: Correctly advertise HBR3 for GEN11+"), but later reverted
due to issues in CI in commit d3913019602e ("Revert "drm/i915/dp:
Correctly advertise HBR3 for GEN11+"").

Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901160402.24816-2-animesh.manna@intel.com

drm/i915/debugfs: clean up LPSP capable

Clean up the LPSP capability printout. No functional changes.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/097390f12da8de57c9d52ad675309d0422dec8fb.1630327990.git.jani.nikula@intel.com

drm/i915/debugfs: clean up LPSP status

Clean up the LPSP status printout. No functional changes.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/c7c2db4e1434ed9a3545f2561a03dc593db5e674.1630327990.git.jani.nikula@intel.com

drm/i915/dp: fix DG2 max source rate check

Accidentally dropped the else in a rebase fail, causing the DG2 max rate
to be overwritten later in the if ladder.

Fixes: e752d1f9c14a ("drm/i915/dg2: add DG2 UHBR source rates")
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210901112815.16498-1-jani.nikula@intel.com

drm/i915/dsi/xelpd: Enable mipi dsi support.

Enable MIPI DSI support on ADL-P platform.
The esc clock changes, WA changes are taken care
in the previous patches.
As per the Bspec the seq remains to be same as TGL.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-3-vandita.kulkarni@intel.com

drm/i915/dsi/xelpd: Add WA to program LP to HS wakeup guardband

Wa_16012360555 SW will have to program the "LP to HS Wakeup Guardband"
field to account for the repeaters on the HS Request/Ready PPI signaling
between the Display engine and the DPHY.

v2: Fix build issue.
v3: Align to new naming (Jani)

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826054811.10572-2-vandita.kulkarni@intel.com

drm/i915/display: Update small joiner ram size

Xelpd supports larger small joiner ram.

Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210805101937.14664-1-vandita.kulkarni@intel.com

drm/i915/display: Renaming DRRS functions to intel_drrs_*()

We had a mix of intel_edp_drrs_*(), intel_dp_drrs_*() and
intel_dp_set_drrs_state(), so properly renaming all functions to
keep the same pattern.

While at it, also dropping intel_dp_set_drrs_state from the
documentation as it is a static function.

v3:
- dropping documentation style comment in static function
(intel_drrs_set_state)

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-3-jose.souza@intel.com

drm/i915/display: Move DRRS code its own file

intel_dp.c is a 5k lines monster, so moving DRRS out of it to reduce
some lines from it.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-2-jose.souza@intel.com

drm/i915/display: Drop PSR support from HSW and BDW

At this point is sure that HSW and BDW will never have PSR enabled by
default, so here dropping it from device info and cleaning up code.

v2:
- enable psr support for display 9

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827174253.51122-1-jose.souza@intel.com

drm/i915/dg2: UHBR tables added for pll programming

UHBR modes has higher link rate and added new values for programming
mpll of SNPS phy. No change in sequence, only the pll parameters
are different for UHBR modes.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210827103843.527-1-jani.nikula@intel.com

drm/i915: remove unused i915->active_pipes

Apparently the last reader of i915->active_pipes was removed with commit
ef79d62b5ce5 ("drm/i915: Encapsulate dbuf state handling harder"), and
now it's only ever written to. Remove it completely.

Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210826141830.889-1-jani.nikula@intel.com

drm/i915/fdi: convert BUG()'s to MISSING_CASE()

These shouldn't happen, but in the off chance they do, we'll want a
warning rather than panic.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b86132ac63f43f79e51eb63f948beccba85bf449.1629906431.git.jani.nikula@intel.com

drm/i915/fdi: move fdi mphy reset and programming to intel_fdi.c

This fairly detailed stuff that really has no place in
intel_display.c. Combine the calls into one to avoid exposing both.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b0037775480380e5d73d0b112da478d6f0ea30fe.1629906431.git.jani.nikula@intel.com

drm/i915/fdi: move more FDI stuff to FDI link train hooks

Accept slight duplication in the fdi link train hooks in exchange for
simplification in ilk_pch_enable(). This lets us make
ivb_update_fdi_bc_bifurcation() static again, now in intel_fdi.c.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7984e670c6bb092d213d90f838d526d594d4a690.1629906431.git.jani.nikula@intel.com

drm/i915/fdi: move fdi bc bifurcation functions to intel_fdi.c

Move FDI related functions to intel_fdi.c. Don't bother with renaming as
we'll make the functions static shortly.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/fd8afe4876f0b0762a9c69e01762a8dba31349e5.1629906431.git.jani.nikula@intel.com

drm/i915/fdi: move intel_update_fdi_pll_freq to intel_fdi.c

Move FDI related functions to intel_fdi.c. Rename to have intel_fdi
prefix while at it.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/da1609dfce4623f8ec86254aea6c2c8679b6a37f.1629906431.git.jani.nikula@intel.com

Merge tag 'drm-misc-intel-oob-hotplug-v1' of git://git./linux/kernel/git/hansg/linux into drm-intel-next

Topic branch for drm-misc / drm-intel for OOB hotplug support for Type-C connectors

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmEf5msUHGhkZWdvZWRl
# QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9xUFQgAtBkpLk/oBn6uRcIXCc8KIGs5NqWG
# orVB7c1Ilsd8jdsap6uD2fVVlS7fn5I6hkiyjdRz5A96aLxkF7oCGLATmxGtYd1k
# lZTUOLXGdl2ye798vuwaO8UzpN7s2yiIaI44GCGLT5Qwrpq9D1tykY3ggXH/03t2
# Z8xOB+XLKbcibnWVQL/4Fz+cQ3KzJ8lo10oiZ131b1ytwf/zdKx0fA3yrPA9C0Kv
# V3dbWxYMWfkO+IUieZgMzl2LrbChp8fC6zmPJYdvlpB7AZXrOKD+4K8JdlKPMZNE
# hi5xF4X1tPeTiOo1jju5JN2hnjsc30JuBLemDcV7CLeL01Y4VLdAwHPwyw==
# =Zar+
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 20 Aug 2021 01:29:15 PM EDT
# gpg:                using RSA key BAF03B5D2718411A5E9E177E92EC4779440327DC
# gpg:                issuer "hdegoede@redhat.com"
# gpg: Can't check signature: No public key
From: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/34f13e21-9b1a-5f54-7e03-9705a6b51428@redhat.com

drm/i915/snps: constify struct intel_mpllb_state arrays harder

The tables should be const arrays of const pointers, not just arrays of
const pointers.

Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210825145811.4227-1-jani.nikula@intel.com

drm/i915/panel: mass rename functions to have intel_panel_ prefix

Follow the usual naming conventions. Also pull HAS_GMCH() check to
intel_panel_fitting(). No functional changes.

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9ff6e42e377bdb0c9349f50d9ea79671059633c7.1629888677.git.jani.nikula@intel.com

drm/i915/backlight: mass rename functions to have intel_backlight_ prefix

Follow the usual naming conventions. As a drive-by cleanup, also pass
intel_connector instead of drm_connector to intel_backlight_setup(). No
functional changes.

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ea1c22370210abdd4f5547af73c71b902061ea50.1629888677.git.jani.nikula@intel.com

drm/i915/backlight: extract backlight code to a separate file

In a long overdue refactoring, split out backlight code to new
intel_backlight.[ch]. Simple code movement, leave renames for follow-up
work. No functional changes.

Cc: Lyude Paul <lyude@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/97d310848f03061473b9b2328e2c5c4dcf263cfa.1629888677.git.jani.nikula@intel.com

drm/i915/dg2: Memory latency values from pcode must be doubled

The memory latency values returned by pcode on DG2 are in units of "2
usec" rather than 1 usec on all other platforms.  I.e., we need to
double the value returned by pcode to obtain the true latency value.

The bspec wording here was a bit ambiguous as to whether it wanted us to
multiply or divide the pcode value by two, but we confirmed offline with
the hardware team that we need to double the value the pcode gives us;
this change is intended to support a larger range of potential latency
values.

Bspec: 49326
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Harish Chegondi <harish.chegondi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210820225710.401136-1-matthew.d.roper@intel.com

drm/i915: Nuke intel_prepare_shared_dpll()

intel_prepare_shared_dpll() is now useless, so get rid of it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-14-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fold ibx_pch_dpll_prepare() into ibx_pch_dpll_enable()

Move the FP divider programming into ibx_pch_dpll_enable(). No reason
that I can see why these would have to be programmed this early.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Fold i9xx_set_pll_dividers() into i9xx_enable_pll()

Can't think of a good reason why we'd need to program the FP
dividers so early. Let's just do it when programming the rest
of the DPLL.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Reuse ilk_needs_fb_cb_tune() for the reduced clock as well

Use ilk_needs_fb_cb_tune() for reduced_clock instead of hand rolling
it. Also ilk_needs_fb_cb_tune() can just use the precomputed M value
instead of calculating it again.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-11-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Call {vlv,chv}_prepare_pll() from {vlv,chv}_enable_pll()

We always call the vlv/chv prepare_pll() just before enable_pll().
Move the calls into the enable_pll() funcs. We can also
consolidate the DPLL_VCO_ENABLE checks while at it.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-10-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Program DPLL P1 dividers consistently

On g4x and pch the DPLL has two P1 dividers (for refresh rate
switching). Program the FPx1 P1 divider consistently to the reduced
clock P1 divider if available, otherwise just program it to the
same value as the FPx0 P1 divider.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-9-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Remove the 'reg' local variable

Get rid of the local 'reg' variable for the DPLL control register
in i9xx_enable_pll(). We have other registers in there too so this
is just making things more confusing.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Clean up variable names in old dpll functions

s/pipe_config/crtc_state/ in the DPLL code.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Clean dpll calling convention

Stop passing both the crtc and its state to the DPLL functions.
The state alone is enough.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Constify struct dpll all over

Lots of places don't need to modify the DPLL params, so make
them const.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Extract ilk_update_pll_dividers()

Make the PCH dpll code match the gmch code by splitting
the FP register handling out from ilk_compute_dpll().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Clean up gen2 DPLL readout

The current gen2 DPLL readout code:
* assumes i845/i865 have LVDS which is not true
* assumes only pipe B can drive LVDS (true, but makes
  the code appear a bit magical)
* hard to parse in general

Clean it up by checking for i85x (the only gen2 platform
with LVDS) and reusing intel_lvds_port_enabled().

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Set output_types to EDP for vlv/chv DPLL forcing

When we enable the DPLL for the PPS kick, let's tell the DPLL code
we're dealing with an eDP output. This shouldn't really matter, but
it's more consistent with the way the DPLL is configured when we're
actually enabling the eDP port for real.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210715093530.31711-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915: Silence __iomem sparse warn

We don't care about __iomem mismatch when dealing with error
pointers. Silence it with ERR_CAST().

drivers/gpu/drm/i915/display/intel_dpt.c:136:21: warning: incorrect type in assignment (different address spaces)
drivers/gpu/drm/i915/display/intel_dpt.c:136:21:    expected struct i915_vma *[assigned] vma
drivers/gpu/drm/i915/display/intel_dpt.c:136:21:    got void [noderef] __iomem *[assigned] iomem

v2: The code moved into intel_dpt.c

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210712161815.24776-1-ville.syrjala@linux.intel.com
Reviewed-by: Matthew Auld <matthew.auld@intel.com>

drm/i915/fb: move user framebuffer stuff to intel_fb.c

Split out fb related stuff from intel_display.c to intel_fb.c.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/76b61738857619c1cce6e4306d14da19ee3bbf08.1629721467.git.jani.nikula@intel.com

drm/i915/fb: move intel_surf_alignment() to intel_fb.c

Split out fb related stuff from intel_display.c to intel_fb.c.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0b894be3a6acff5fe917b686771a084a6c2aa535.1629721467.git.jani.nikula@intel.com

drm/i915/fb: move intel_fb_align_height() to intel_fb.c

Split out fb related stuff from intel_display.c to intel_fb.c.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/7c97d29eeff676b510eafd242e2a6d7c8ed4a3a6.1629721467.git.jani.nikula@intel.com

drm/i915/fb: move intel_tile_width_bytes() to intel_fb.c

Split out fb related stuff from intel_display.c to intel_fb.c.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/35c3ade81a54fea890cf92e21b778c38ab78cd04.1629721467.git.jani.nikula@intel.com

drm/i915: add HAS_ASYNC_FLIPS feature macro

This will be needed in multiple places soon.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/08bf0f72435a4f9acb0ef31b82ca312b048c6bf6.1629721467.git.jani.nikula@intel.com

drm/i915/display: split out dpt out of intel_display.c

Let's try to reduce the size of intel_display.c, not increase it.

Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/934a2a0db05e835f6843befef6082e2034f23b3a.1629721467.git.jani.nikula@intel.com

drm/i915/fdi: make intel_fdi_link_freq() return int

The unsigned doesn't help us here.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210823093645.10464-1-jani.nikula@intel.com

drm/i915/dp: Drop redundant debug print

drm_dp_dpcd_read/write already has debug error message.
Drop redundant error messages which gives false
status even if correct value is read in drm_dp_dpcd_read().

v2: -Added fixes tag (Ankit)
v3: -Fixed build error (CI)

Fixes: 9488a030ac91 ("drm/i915: Add support for enabling link status and recovery")
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.12+
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812131107.5531-1-swati2.sharma@intel.com

drm/i915/dp: add max data rate calculation for UHBR rates

DP 2.0 UHBR link rates always use 128b/132b channel encoding, which has
a different data bandwidth efficiency from 8b/10b. The computation is
slightly convoluted due to the units we use; this is all explained in
the added comment.

v2: Clarified comment (Manasi)

Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8afd8d97a04c2d86c2dcadfed9f8e1f84272a13c.1629735412.git.jani.nikula@intel.com

drm/i915/dg2: add DG2 UHBR source rates

DG2 supports DP 2.0 UHBR and 128b/132b channel encoding.

Bspec: 53657, 54034
Acked-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8f82b7eb76f20f1c4ddd2cc7d1bb31e2173c55a6.1629735412.git.jani.nikula@intel.com

drm/i915/dg2: add TRANS_DP2_VFREQHIGH and TRANS_DP2_VFREQLOW

Add the registers for specifying the lower and higher 24 bits of the DP
2.0 pixel clock frequency in Hz.

Bspec: 53326
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9047f10318a30bc03ce8516ee3f5512437a95663.1629735412.git.jani.nikula@intel.com

drm/i915/dg2: add TRANS_DP2_CTL register definition

This register controls the DP 2.0 datapath.

Bspec: 69967
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0d3529df4501c5dd8ad1da0b6dbaabcfa97510b4.1629735412.git.jani.nikula@intel.com

drm/i915/dp: read sink UHBR rates

See if sink supports DP 2.0 128b/132b channel encoding, and update sink
rates accordingly.

FIXME: Also take LTTPR 128b/132b into account.

v2: Add build-time check for ->sink_rates size (Ville)

Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/089d807e887d308c52c84cf58dfb6777de18872d.1629735412.git.jani.nikula@intel.com

drm/i915/dp: use actual link rate values in struct link_config_limits

The MST code uses actual link rates in the limits struct, while the DP
code in general uses indexes to the ->common_rates[] array. Fix the
confusion by using actual link rate values everywhere. This is a better
abstraction than some obscure index.

Rename the struct members while at it to ensure all the places are
covered.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d70ab7261abacd367d3a6a47102575eb88a55cd4.1629735412.git.jani.nikula@intel.com

drm/i915/adl_s: Update ADL-S PCI IDs

Sync PCI IDs with Bspec.

Bspec:53655

Changes since V2:
- Upstream devices which are "POR" yes and
  "Ok to upstream" yes - James Asmus
Changes since V1:
        - All POR and Non POR Ids needs to be upstreamed - James Asmus

Signed-off-by: Tejas Upadhyay <tejaskumarx.surendrakumar.upadhyay@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210818050116.1116237-1-tejaskumarx.surendrakumar.upadhyay@intel.com

drm/i915/dp: Use max params for panels < eDP 1.4

Users reported that after commit 2bbd6dba84d4 ("drm/i915: Try to use
fast+narrow link on eDP again and fall back to the old max strategy on
failure"), the screen starts to have wobbly effect.

Commit a5c936add6a2 ("drm/i915/dp: Use slow and wide link training for
everything") doesn't help either, that means the affected eDP 1.2 panels
only work with max params.

So use max params for panels < eDP 1.4 as Windows does to solve the
issue.

v3:
 - Do the eDP rev check in intel_edp_init_dpcd()

v2:
 - Check eDP 1.4 instead of DPCD 1.1 to apply max params

Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3714
Fixes: 2bbd6dba84d4 ("drm/i915: Try to use fast+narrow link on eDP again and fall back to the old max strategy on failure")
Fixes: a5c936add6a2 ("drm/i915/dp: Use slow and wide link training for everything")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210820075301.693099-1-kai.heng.feng@canonical.com

drm/i915/fbc: Polish the skl+ FBC stride override handling

Polish the FBC stride override stuff:
- just call it override_cfb_stride since it'll be used on
  more gens later
- Use REG_BIT() & co. for the registers and give everything
  CHICKEN_ prefix since glk+ will have a different register
  for this
- Use intel_de_rmw() for the RMW

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702204603.596-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>

drm/i915/fbc: Move the "recompress on activate" to a central place

On ILK+ we current do a nuke right after activating FBC. If my
memory isn't playing tricks on me this is actially required if
FBC didn't stay disabled for a full frame. In that case the
deactivate+reactivate may not invalidate the cfb. I'd have to
double chekc to be sure though.

So let's keep the nuke, and just extend it backwards to cover
all the platforms by doing it a bit higher up.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702204603.596-4-ville.syrjala@linux.intel.com

drm/i915/fbc: Extract intel_fbc_update()

Pull the fbc enable vs. disable stuff into a small helper so
we don't have to have it pollute the higher level modeset code.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702204603.596-3-ville.syrjala@linux.intel.com

drm/i915/fbc: Rewrite the FBC tiling check a bit

Write the tiling check in a nicer form. No functional
changes due to Y-tile scanout being a gen9+ feature.

Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702204603.596-2-ville.syrjala@linux.intel.com

usb: typec: altmodes/displayport: Notify drm subsys of hotplug events

Use the new drm_connector_oob_hotplug_event() functions to let drm/kms
drivers know about DisplayPort over Type-C hotplug events.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-9-hdegoede@redhat.com

usb: typec: altmodes/displayport: Make dp_altmode_notify() more generic

Make dp_altmode_notify() handle the dp->data.conf == 0 case too,
rather then having separate code-paths for this in various places
which call it.

Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-8-hdegoede@redhat.com

drm/connector: Add support for out-of-band hotplug notification (v3)

Add a new drm_connector_oob_hotplug_event() function and
oob_hotplug_event drm_connector_funcs member.

On some hardware a hotplug event notification may come from outside the
display driver / device. An example of this is some USB Type-C setups
where the hardware muxes the DisplayPort data and aux-lines but does
not pass the altmode HPD status bit to the GPU's DP HPD pin.

In cases like this the new drm_connector_oob_hotplug_event() function can
be used to report these out-of-band events.

Changes in v2:
- Make drm_connector_oob_hotplug_event() take a fwnode as argument and
  have it call drm_connector_find_by_fwnode() internally. This allows
  making drm_connector_find_by_fwnode() a drm-internal function and
  avoids code outside the drm subsystem potentially holding on the
  a drm_connector reference for a longer period.

Changes in v3:
- Drop the data argument to the drm_connector_oob_hotplug_event
  function since it is not used atm. This can be re-added later when
  a use for it actually arises.

Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-5-hdegoede@redhat.com

drm/connector: Add drm_connector_find_by_fwnode() function (v3)

Add a function to find a connector based on a fwnode.

This will be used by the new drm_connector_oob_hotplug_event()
function which is added by the next patch in this patch-set.

Changes in v2:
- Complete rewrite to use a global connector list in drm_connector.c
  rather then using a class-dev-iter in drm_sysfs.c

Changes in v3:
- Add forward declaration for struct fwnode_handle to drm_crtc_internal.h
  (fixes warning reported by kernel test robot <lkp@intel.com>)

Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-4-hdegoede@redhat.com

drm/connector: Add a fwnode pointer to drm_connector and register with ACPI (v2)

Add a fwnode pointer to struct drm_connector and register an acpi_bus_type
for the connectors with the ACPI subsystem (when CONFIG_ACPI is enabled).

The adding of the fwnode pointer allows drivers to associate a fwnode
that represents a connector with that connector.

When the new fwnode pointer points to an ACPI-companion, then the new
acpi_bus_type will cause the ACPI subsys to bind the device instantiated
for the connector with the fwnode by calling acpi_bind_one(). This will
result in a firmware_node symlink under /sys/class/card#-<connecter-name>/
which helps to verify that the fwnode-s and connectors are properly
matched.

Changes in v2:
- Make drm_connector_cleanup() call fwnode_handle_put() on
  connector->fwnode and document this

Co-developed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-3-hdegoede@redhat.com

drm/connector: Give connector sysfs devices there own device_type

Give connector sysfs devices there own device_type, this allows us to
check if a device passed to functions dealing with generic devices is
a drm_connector or not.

A check like this is necessary in the drm_connector_acpi_bus_match()
function added in the next patch in this series.

Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20210817215201.795062-2-hdegoede@redhat.com

drm/i915/fdi: move intel_fdi_link_freq() to intel_fdi.[ch]

There's no performance reason to have it as static inline; move it out
of intel_display_types.h to reduce clutter and dependency on i915_drv.h.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8c9bb23d92878deb1ecc75427ec6648bd3505816.1629281426.git.jani.nikula@intel.com

drm/i915/panel: move intel_panel_use_ssc() out of headers

There's no performance reason to have it as static inline; move it out
of intel_display_types.h to reduce clutter and dependency on i915_drv.h.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6f2c05005e4fa43a5572b02b3f41363725ffdb4f.1629281426.git.jani.nikula@intel.com

drm/i915/pm: use forward declaration to remove an include

The fewer includes the better.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/dcb426e4c6497f9ee3356c5f4fd4aaabd6295262.1629281426.git.jani.nikula@intel.com

drm/i915: intel_runtime_pm.h does not actually need intel_display.h

Reduce includes.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/289a6837379c4422395c3ac2b36a6c2a44110227.1629281426.git.jani.nikula@intel.com

drm/i915/irq: reduce inlines to reduce header dependencies

Presumably if the compiler is smart, it does not generate an extra
function call to the update functions that are now static.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/594f628740717cda5ef407a26ea03129c22ddc12.1629281426.git.jani.nikula@intel.com

drm/i915/adl_p: Also disable underrun recovery with MSO

One of the cases that the bspec lists for when underrun recovery must be
disabled is "COG;" that note actually refers to eDP multi-segmented
operation (MSO).  Let's ensure the this additional restriction is
honored by the driver.

Bspec: 50351
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: ba3b049f4774 ("drm/i915/adl_p: Allow underrun recovery when possible")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210816204112.2960624-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915/dp: return proper DPRX link training result

After DPRX link training, intel_dp_link_train_phy() did not
return the training result properly. If link training failed,
i915 driver would not run into link train fallback function.
And no hotplug uevent would be received by user space application.

Fixes: b30edfd8d0b4 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706152541.25021-1-shawn.c.lee@intel.com

drm/i915: Nuke ORIGIN_GTT

There is no users of it, so no need to keep handling for it.

Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210815014346.373945-2-jose.souza@intel.com

drm/i915/display: Fix sel fetch plane offset calculation

skl_calc_main_surface_offset() is used to calculate an aligned plane
surface address considering the inner framebuffer x and y offset.
It can not be used by selective fetch functions becase there is no
PLANE_SEL_FETCH_SURF.
So the PLANE_SEL_FETCH_OFFSET.y should only be PLANE_OFFSET.y +
damaged_area_within_plane.y1.

This fixes glitches seen in fbcon caused by typing something in
the terminal.

BSpec: 55229
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210815014346.373945-1-jose.souza@intel.com

drm/i915/dp: remove superfluous EXPORT_SYMBOL()

The symbol isn't needed outside of i915.ko.

Fixes: b30edfd8d0b4 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Fixes: 264613b406eb ("drm/i915: Disable LTTPR support when the DPCD rev < 1.4")
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210816071737.2917-1-jani.nikula@intel.com

Merge drm/drm-next into drm-intel-next

Catch up with drm core changes.

Signed-off-by: Jani Nikula <jani.nikula@intel.com>

Merge tag 'drm-misc-next-2021-08-12' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

drm-misc-next for v5.15:

UAPI Changes:

Cross-subsystem Changes:
- Add lockdep_assert(once) helpers.

Core Changes:
- Add lockdep assert to drm_is_current_master_locked.
- Fix typos in dma-buf documentation.
- Mark drm irq midlayer as legacy only.
- Fix GPF in udmabuf_create.
- Rename member to correct value in drm_edid.h

Driver Changes:
- Build fix to make nouveau build with NOUVEAU_BACKLIGHT.
- Add MI101AIT-ICP1, LTTD800480070-L6WWH-RT panels.
- Assorted fixes to bridge/it66121, anx7625.
- Add custom crtc_state to simple helpers, and use it to
  convert pll handling in mgag200 to atomic.
- Convert drivers to use offset-adjusted framebuffer bo mappings.
- Assorted small fixes and fix for a use-after-free in vmwgfx.
- Convert remaining callers of non-legacy drivers to use linux irqs directly.
- Small cleanup in ingenic.
- Small fixes to virtio and ti-sn65dsi86.

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1cf2d7fc-402d-1852-574a-21cbbd2eaebf@linux.intel.com

drm/i915/dg2: add SNPS PHY translations for UHBR link rates

UHBR link rates use different tx equalization settings. Using this will
require changes in the link training code too.

Bspec: 53920
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210813115151.19290-3-jani.nikula@intel.com

drm/i915/dg2: use existing mechanisms for SNPS PHY translations

We use encoder->get_buf_trans() in many places, for example
intel_ddi_dp_voltage_max(), and the hook was set to some old platform's
function for DG2 SNPS PHY. Convert SNPS PHY to use the same translation
mechanisms as everything else.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210813115151.19290-2-jani.nikula@intel.com

drm/i915/dp: pass crtc_state to intel_ddi_dp_level()

Needed in the future.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210813115151.19290-1-jani.nikula@intel.com

drm/i915/mst: use intel_de_rmw() to simplify VC payload alloc set/clear

Less is more, fewer lines to wonder about.

Cc: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210813115610.20010-1-jani.nikula@intel.com

drm/i915/edp: fix eDP MSO pipe sanity checks for ADL-P

ADL-P supports stream splitter on pipe B in addition to pipe A. Update
the sanity check in intel_ddi_mso_get_config() to reflect this, and
remove the check in intel_ddi_mso_configure() as redundant with
encoder->pipe_mask. Abstract the splitter pipe mask to a single point of
truth while at it to avoid similar mistakes in the future.

Fixes: 7bc188cc2c8c ("drm/i915/adl_p: enable MSO on pipe B")
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Reviewed-by: Swati Sharma <swati2.sharma@intel.com>
Tested-by: Swati Sharma <swati2.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812132354.10885-1-jani.nikula@intel.com

fbdev/efifb: Release PCI device's runtime PM ref during FB destroy

Atm the EFI FB platform driver gets a runtime PM reference for the
associated GFX PCI device during probing the EFI FB platform device and
releases it only when the platform device gets unbound.

When fbcon switches to the FB provided by the PCI device's driver (for
instance i915/drmfb), the EFI FB will get only unregistered without the
EFI FB platform device getting unbound, keeping the runtime PM reference
acquired during the platform device probing. This reference will prevent
the PCI driver from runtime suspending the device.

Fix this by releasing the RPM reference from the EFI FB's destroy hook,
called when the FB gets unregistered.

While at it assert that pm_runtime_get_sync() didn't fail.

v2:
- Move pm_runtime_get_sync() before register_framebuffer() to avoid its
  race wrt. efifb_destroy()->pm_runtime_put(). (Daniel)
- Assert that pm_runtime_get_sync() didn't fail.
- Clarify commit message wrt. platform/PCI device/driver and driver
  removal vs. device unbinding.

Fixes: a6c0fd3d5a8b ("efifb: Ensure graphics device for efifb stays at PCI D0")
Cc: Kai-Heng Feng <kai.heng.feng@canonical.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210809133146.2478382-1-imre.deak@intel.com

drm/bridge: ti-sn65dsi86: Avoid creating multiple connectors

If we created our own connector because the driver does not support the
NO_CONNECTOR flag, we don't want the downstream bridge to *also* create
a connector.  And if this driver did pass the NO_CONNECTOR flag (and we
supported that mode) this would change nothing.

Fixes: 4e5763f03e10 ("drm/bridge: ti-sn65dsi86: Wrap panel with panel-bridge")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210811235253.924867-2-robdclark@gmail.com

drm/edid: fix edid field name

Byte 26 in a edid struct is supposed to be "Blue and white
least-significant 2 bits", not "black and white". Rename the field
accordingly. This field is not used anywhere, so just renaming it here
for correctness.

Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Signed-off-by: Simon Ser <contact@emersion.fr>
Link: https://patchwork.freedesktop.org/patch/msgid/20210811205818.156100-1-lucas.demarchi@intel.com

drm/virtio: set non-cross device blob uuid_state

Blob resources without the cross device flag don't have a uuid to share
with other virtio devices. When exporting such blobs, set uuid_state to
STATE_ERR so that virtgpu_virtio_get_uuid doesn't hang.

Signed-off-by: David Stevens <stevensd@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20210811040401.1264234-1-stevensd@chromium.org
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/i915: Tweaked Wa_14010685332 for all PCHs

dispcnlunit1_cp_xosc_clkreq clock observed to be active on TGL-H platform
despite Wa_14010685332 original sequence,
thus blocks entry to deeper s0ix state.

The Tweaked Wa_14010685332 sequence fixes this issue, therefore use tweaked
Wa_14010685332 sequence for every PCH since PCH_CNP.

v2:
- removed RKL from comment and simplified condition. [Rodrigo]

Fixes: b896898c7369 ("drm/i915: Tweaked Wa_14010685332 for PCHs used on gen11 platforms")
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210810113112.31739-2-anshuman.gupta@intel.com

udmabuf: fix general protection fault in udmabuf_create

Syzbot reported general protection fault in udmabuf_create. The problem
was in wrong error handling.

In commit 16c243e99d33 ("udmabuf: Add support for mapping hugepages (v4)")
shmem_read_mapping_page() call was replaced with find_get_page_flags(),
but find_get_page_flags() returns NULL on failure instead PTR_ERR().

Wrong error checking was causing GPF in get_page(), since passed page
was equal to NULL. Fix it by changing if (IS_ER(!hpage)) to if (!hpage)

Reported-by: syzbot+e9cd3122a37c5d6c51e8@syzkaller.appspotmail.com
Fixes: 16c243e99d33 ("udmabuf: Add support for mapping hugepages (v4)")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20210811175052.21254-1-paskripkin@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

Merge tag 'drm-intel-next-2021-08-10-1' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

drm/i915 changes for v5.15:

Features:
- Basic DG2 platform enabling (Matt, Animesh, Gwan-gyeong, José)
- Add PSF GV point support for display bandwidth calculation (Stan)
- Add platform release id version support (Lucas)
- Add support for forcing DSC BPP for testing (Vandita, Patnana)

Refactoring and cleanups:
- Remove CNL support completely (Lucas)
- Revid/stepping cleanup (Matt, Anusha)
- Make display stepping check upper bounds exclusive (Matt)
- Remove old GEN macros (Lucas)
- Refactor DG1 interrupt handler (Paulo)
- Refactor DMC stepping info (Anusha)

Fixes:
- Fix XELPD color capability reporting; it's not yet enabled (Uma)
- Fix DG1 memory bandwidth computation (Clint)
- Fix mux on certain HP laptops (Kai-Heng)
- Various display workarounds (José, Matt, Imre)
- Fix error state dumps wrt SFC_DONE (Matt)
- Fix DG1 and XEPLD audio power domains (Anshuman)
- Fix ADL-P and ADL-S ddi buf translation tables (Matt)
- Fix DP/HDMI modeset sequences causing issues on ADL-P (José)
- PSR2 fixes (José)
- Fix DP MST modeset with FEC on TGL+
- Fix MBUS DBOX A credits on ADL-P (José)
- Fix DP PHY test training set programming (Khaled)
- Fix dgfx pcode uncore init done wait (Badal)
- Fix DSC disable fuse check on GLK (Lucas)
- Fix shared dpll mismatch for bigjoiner secondary pipe (Manasi)
- Fix ADL-P underrun recovery (Matt)
- Fix permissions on FEC support debugfs file (Vandita)

Misc:
- Backmerge drm-next (Rodrigo)
- Bump RKL and TGL DMC firmware version (Anusha)

Signed-off-by: Dave Airlie <airlied@redhat.com>
# Conflicts:
# drivers/gpu/drm/i915/i915_drv.h
# drivers/gpu/drm/i915/intel_device_info.h
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87a6lpo1a9.fsf@intel.com

Merge tag 'drm-xilinx-dpsub-20210809' of git://linuxtv.org/pinchartl/media into drm-next

- Miscellaneous fixes in ZynqMP DPSUB driver

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YRCSRZZV1HZYPvaG@pendragon.ideasonboard.com

Merge tag 'drm-intel-gt-next-2021-08-06-1' of ssh://git.freedesktop.org/git/drm/drm-intel into drm-next

UAPI Changes:

- Add I915_MMAP_OFFSET_FIXED

  On devices with local memory `I915_MMAP_OFFSET_FIXED` is the only valid
  type. On devices without local memory, this caching mode is invalid.

  As caching mode when specifying `I915_MMAP_OFFSET_FIXED`, WC or WB will
  be used, depending on the object placement on creation. WB will be used
  when the object can only exist in system memory, WC otherwise.

  Userspace: https://gitlab.freedesktop.org/mesa/mesa/-/merge_requests/11888

- Reinstate the mmap ioctl for (already released) integrated Gen12 platforms

  Rationale: Otherwise media driver breaks eg. for ADL-P. Long term goal is
  still to sunset the IOCTL even for integrated and require using mmap_offset.

- Reject caching/set_domain IOCTLs on discrete

  Expected to become immutable property of the BO

- Disallow changing context parameters after first use on Gen12 and earlier
- Require setting context parameters at creation on platforms after Gen12

  Rationale (for both): Allow less dynamic changes to the context to simplify
  the implementation and avoid user shooting theirselves in the foot.

- Drop I915_CONTEXT_PARAM_RINGSIZE

  Userspace PR for compute-driver has not been merged

- Drop I915_CONTEXT_PARAM_NO_ZEROMAP

  Userspace PR for libdrm / Beignet was never landed

- Drop CONTEXT_CLONE API

  Userspace PR for Mesa was never landed

- Drop getparam support for I915_CONTEXT_PARAM_ENGINES

  Only existed for symmetry wrt. setparam, never used.

- Disallow bonding of virtual engines

  Drop the prep work, no hardware has been released needing it.

- (Implicit) Disable gpu relocations

  Media userspace was the last userspace to still use them. They
  have converted so performance can be regained with an update.

Core Changes:

- Merge topic branch 'topic/i915-ttm-2021-06-11' (from Maarten)
- Merge topic branch 'topic/revid_steppings' (from Matt R)
- Merge topic branch 'topic/xehp-dg2-definitions-2021-07-21' (from Matt R)
- Backmerges drm-next (Rodrigo)

Driver Changes:

- Initial workarounds for ADL-P (Clint)
- Preliminary code for XeHP/DG2 (Stuart, Umesh, Matt R, Prathap, Ram,
  Venkata, Akeem, Tvrtko, John, Lucas)
- Fix ADL-S DMA mask size to 39 bits (Tejas)
- Remove code for CNL (Lucas)
- Add ADL-P GuC/HuC firmwares (John)
- Update HuC to 7.9.3 for TGL/ADL-S/RKL (John)
- Fix -EDEADLK handling regression (Ville)
- Implement Wa_1508744258 for DG1 and Gen12 iGFX (Jose)
- Extend Wa_1406941453 to ADL-S (Jose)
- Drop unnecessary workarounds per stepping for SKL/BXT/ICL (Matt R)
- Use fuse info to enable SFC on Gen12 (Venkata)
- Unconditionally flush the pages on acquire on EHL/JSL (Matt A)
- Probe existence of backing struct pages upon userptr creation (Chris, Matt A)

- Add an intermediate GEM proto-context to delay real context creation (Jason)
- Implement SINGLE_TIMELINE with a syncobj (Jason)
- Set the watchdog timeout directly in intel_context_set_gem (Jason)
- Disallow userspace from creating contexts with too many engines (Jason)
- Revert "drm/i915/gem: Asynchronous cmdparser" (Jason)
- Revert "drm/i915: Propagate errors on awaiting already signaled fences" (Jason)
- Revert "drm/i915: Skip over MI_NOOP when parsing" (Jason)
- Revert "drm/i915: Shrink the GEM kmem_caches upon idling" (Daniel)
- Always let TTM handle object migration (Jason)
- Correct the locking and pin pattern for dma-buf (Thomas H, Michael R, Jason)
- Migrate to system at dma-buf attach time (Thomas, Michael R)

- MAJOR refactoring of the GuC backend code to allow for enabling on Gen11+
  (Matt B, John, Michal Wa., Fernando, Daniele, Vinay)
- Update GuC firmware interface to v62.0.0 (John, Michal Wa., Matt B)
- Add GuCRC feature to hand over the control of HW RC6 to the GuC on
  Gen12+ when GuC submission is enabled (Vinay, Sujaritha, Daniele,
  John, Tvrtko)
- Use the correct IRQ during resume and eliminate DRM IRQ midlayer (Thomas Z)
- Add pipelined page migration and clearing (Chris, Thomas H)
- Use TTM for system memory on discrete (Thomas H)
- Implement object migration for display vs. dma-buf (Thomas H)
- Perform execbuffer object locking as a separate step (Thomas H)
- Add support for explicit L3BANK steering (Matt, Daniele)
- Remove duplicated call to ops->pread (Daniel)
- Fix pagefault disabling in the first execbuf slowpath (Daniel)
- Simplify userptr locking (Thomas H)
- Improvements to the GuC CTB code (Matt B, John)
- Make GT workaround upper bounds exclusive (Matt R)
- Check for nomodeset in i915_init() first (Daniel)
- Delete now unused gpu reloc code (Daniel)

- Document RFC plans for GuC submission, DRM scheduler and new parallel
  submit uAPI (Matt B)
- Reintroduce buddy allocator this time with TTM (Matt A)
- Support forcing page size with LMEM (Matt A)
- Add i915_sched_engine to abstract a submission queue between backends (Matt B)
- Use accelerated move in TTM (Ram)
- Fix memory leaks from TTM backend (Thomas H)
- Introduce WW transaction helper (Thomas H)
- Improve debug Kconfig texts a bit (Daniel)
- Unify user object creation code (Jason)
- Use a table for i915_init/exit (Jason)
- Move slabs to module init/exit (Daniel)
- Remove now unused i915_globals (Daniel)
- Extract i915_module.c (Daniel)

- Consistently use adl-p/adl-s in WA comments (Jose)
- Finish INTEL_GEN and friends conversion (Lucas)
- Correct variable/function namings (Lucas)
- Code checker fixes (Wan, Matt A)
- Tracepoint improvements (Matt B)
- Kerneldoc improvements (Tvrtko, Jason, Matt A, Maarten)
- Selftest improvements (Chris, Matt A, Tejas, Thomas H, John, Matt B,
  Rahul, Vinay)

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YQ0JmYiXhGskNcrI@jlahtine-mobl.ger.corp.intel.com

drm/i915: Only access SFC_DONE when media domain is not fused off

The SFC_DONE register lives within the corresponding VD0/VD2/VD4/VD6
forcewake domain and is not accessible if the vdbox in that domain is
fused off and the forcewake is not initialized.

This mistake went unnoticed because until recently we were using the
wrong register offset for the SFC_DONE register; once the register
offset was corrected, we started hitting errors like

  <4> [544.989065] i915 0000:cc:00.0: Uninitialized forcewake domain(s) 0x80 accessed at 0x1ce000

on parts with fused-off vdbox engines.

Fixes: e50dbdbfd9fb ("drm/i915/tgl: Add SFC instdone to error state")
Fixes: 82929a2140eb ("drm/i915: Correct SFC_DONE register offset")
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806174130.1058960-1-matthew.d.roper@intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>

drm/i915/dg2: Configure PCON in DP pre-enable path

Add the functions to configure HDMI2.1 pcon for DG2, before DP link
training.

Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210805163647.801064-10-matthew.d.roper@intel.com

drm/ingenic: Use standard drm_atomic_helper_commit_tail

By making the CRTC's .vblank_enable() function return an error when it
is known that the hardware won't deliver a VBLANK, we can drop the
ingenic_drm_atomic_helper_commit_tail() function and use the standard
drm_atomic_helper_commit_tail() function instead.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210808134526.119198-4-paul@crapouillou.net

drm/ingenic: Remove dead code

The priv->ipu_plane would get a different value further down the code,
without the first assigned value being read first; so the first
assignation can be dropped.

Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210808134526.119198-2-paul@crapouillou.net

drm/i915/display: Fix the 12 BPC bits for PIPE_MISC reg

Till DISPLAY12 the PIPE_MISC bits 5-7 are used to set the
Dithering BPC, with valid values of 6, 8, 10 BPC.
For ADLP+ these bits are used to set the PORT OUTPUT BPC, with valid
values of: 6, 8, 10, 12 BPC, and need to be programmed whether
dithering is enabled or not.

This patch:
-corrects the bits 5-7 for PIPE MISC register for 12 BPC.
-renames the bits and mask to have generic names for these bits for
dithering bpc and port output bpc.

v3: Added a note for MIPI DSI which uses the PIPE_MISC for readout
for pipe_bpp. (Uma Shankar)

v2: Added 'display' to the subject and fixes tag. (Uma Shankar)

Fixes: 756f85cffef2 ("drm/i915/bdw: Broadwell has PIPEMISC")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210811051857.109723-1-ankit.k.nautiyal@intel.com

Merge tag 'amd-drm-next-5.15-2021-08-06' of https://gitlab.freedesktop.org/agd5f/linux into drm-next

amd-drm-next-5.15-2021-08-06:

amdgpu:
- Aldebaran fixes
- Powergating fix for Renoir
- Switch virtual DCE over to vkms based atomic modesetting
- Misc typo fixes
- PSP handling cleanups
- DC FP cleanups
- RAS fixes
- Wave debug improvements
- Freesync fix
- BACO/BOCO fixes
- Misc fixes

amdkfd:
- Expose gfx version in sysfs
- Aldebaran fixes

radeon:
- Coding style fix
- Typo fixes
- Pageflip fix

UAPI:
- amdkfd: SVM address range query
  Proposed userspace: https://github.com/RadeonOpenCompute/ROCR-Runtime/tree/memory_model_queries

Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210806205248.3864-1-alexander.deucher@amd.com

Merge tag 'bus_remove_return_void-5.15' of git://git./linux/kernel/git/gregkh/driver-core into drm-next

Bus: Make remove callback return void tag

Tag for other trees/branches to pull from in order to have a stable
place to build off of if they want to add new busses for 5.15.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: fixed up merge conflict in drm]
From:   Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://patchwork.freedesktop.org/patch/msgid/YPkwQwf0dUKnGA7L@kroah.com

drm: IRQ midlayer is now legacy

Hide the DRM midlayer behind CONFIG_DRM_LEGACY, make functions use
the prefix drm_legacy_, and move declarations to drm_legacy.h.
In struct drm_device, move the fields irq and irq_enabled behind
CONFIG_DRM_LEGACY.

All callers have been updated.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-15-tzimmermann@suse.de

drm: Remove unused devm_drm_irq_install()

DRM IRQ helpers will become legacy. The function devm_drm_irq_install()
is unused and won't be required later.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-14-tzimmermann@suse.de

drm/vc4: Convert to Linux IRQ interfaces

Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.

DRM IRQ callbacks are now being called directly or inlined.

Calls to platform_get_irq() can fail with a negative errno code.
Abort initialization in this case. The DRM IRQ midlayer does not
handle this case correctly.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-13-tzimmermann@suse.de

drm/tilcdc: Convert to Linux IRQ interfaces

Drop the DRM IRQ midlayer in favor of Linux IRQ interfaces. DRM's
IRQ helpers are mostly useful for UMS drivers. Modern KMS drivers
don't benefit from using it.

DRM IRQ callbacks are now being called directly or inlined.

Calls to platform_get_irq() can fail with a negative errno code.
Abort initialization in this case. The DRM IRQ midlayer does not
handle this case correctly.

For most drivers, only the DRM IRQ helpers use irq_enabled from
struct drm_device. Tilcdc also uses irq_enabled to make its error
rollback work correctly. As the field will become legacy, duplicated
the state in the driver's local private structure.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210803090704.32152-12-tzimmermann@suse.de