Simon Glass [Sat, 5 Sep 2020 20:50:45 +0000 (14:50 -0600)]
x86: zboot: Add an 'info' subcommand
Add a little subcommand that prints out where the kernel was loaded and
its setup pointer. Run it by default in the normal boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:44 +0000 (14:50 -0600)]
x86: zboot: Add a 'go' subcommand
Split out the code that actually boots linux into a separate sub-command.
Add base_ptr to the state to support this.
Show an error if the boot fails, since this should not happen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:43 +0000 (14:50 -0600)]
x86: zboot: Set up a sub-command structure
Add subcommands to zboot. At present there is only one called 'start'
which does the whole boot. It is the default command so is optional.
Change the 's' string variable to const while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: reduce maxargs to 6 of 'zboot start' subcommand]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:42 +0000 (14:50 -0600)]
x86: zimage: Disable interrupts just before booting
At present if an error occurs while setting up the boot, interrupts are
left disabled. Move this call later in the sequence to avoid this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:41 +0000 (14:50 -0600)]
x86: zboot: Correct image type
At present U-Boot sets a loader type of 8 which means LILO version 8,
according to the spec. Update it to 0x80, which means U-Boot with no
particular version.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:40 +0000 (14:50 -0600)]
x86: zboot: Move kernel-version code into a function
To help reduce the size and complexity of load_zimage(), move the code
that reads the kernel version into a separate function. Update
get_boot_protocol() to allow printing the 'Magic signature' message only
once, under control of its callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:39 +0000 (14:50 -0600)]
x86: zimage: Avoid using #ifdef
Use IS_ENABLED() instead of #ifdef in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:38 +0000 (14:50 -0600)]
x86: zimage: Use a state struct to hold the state
At present the 'zboot' command does everything in one go. It would be
better if it supported sub-commands like bootm, so it is possible to
examine what will be booted before actually booting it.
In preparation for this, move the 'state' of the command into a struct.
This will allow it to be shared among multiple functions in this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sat, 5 Sep 2020 20:50:37 +0000 (14:50 -0600)]
x86: Update the bootparam header
This header is missing a few of the newer features from the specification.
Add these as well as a link to the spec. Also use the BIT() macros where
appropriate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tom Rini [Thu, 24 Sep 2020 12:30:25 +0000 (08:30 -0400)]
Merge branch 'mpc85xx-for-v2021.01' into next
- Add DM_SPI, DM_SPI_FLASH support for powerpc platforms
- Add DM_ETH support on P1010RDB, P1020RDB, P2020RDB
- Remove some un-maintained powerpc platforms
- Add USB_STORAGE support in config
Ran Wang [Tue, 30 Jun 2020 05:08:34 +0000 (13:08 +0800)]
configs: powerpc: add usb (host) mass storage support
commit
0cfccb54014b ("configs: Resync with savedefconfig")
removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig
files, whicih would block the use case of system loading rootfs
from USB drives, add them back.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:45 +0000 (11:56 +0530)]
configs: Remove P5040DS secure boot configs
Remove NXP powerpc P5040DS secure boot configs as they are
no longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:44 +0000 (11:56 +0530)]
board/freescale: Remove P5020DS board support
Remove NXP powerpc P5020DS board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:43 +0000 (11:56 +0530)]
powerpc:Remove P4080DS secure boot configs
Remove NXP powerpc P4080DS secure boot configs as they are
no longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:42 +0000 (11:56 +0530)]
configs: Remove P3041DS secure boot configs
Remove NXP powerpc P3041DS secure boot configs as they are
no longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:41 +0000 (11:56 +0530)]
board/freescale: Remove P1024RDB board support
Remove NXP powerpc P1024RDB board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 10:06:25 +0000 (15:36 +0530)]
board/freescale: Remove P1021RDB board support
Remove NXP powerpc P1021RDB board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:39 +0000 (11:56 +0530)]
board/freescale: Remove P1020MBG board support
Remove NXP powerpc P1020MBG board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:38 +0000 (11:56 +0530)]
board/freescale: Remove P1020UTM board support
Remove NXP powerpc P1020UTM board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 10:05:16 +0000 (15:35 +0530)]
board/freescale: Remove P1025RDB board support
Remove NXP powerpc P1025RDB board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:36 +0000 (11:56 +0530)]
configs: Remove P1010RDB secure boot configs
Remove NXP powerpc P1010RDB secure boot configs as they are
no longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Priyanka Jain [Mon, 21 Sep 2020 06:26:35 +0000 (11:56 +0530)]
board/freescale: Remove p1023rdb board support
Remove NXP powerpc p1023rdb board support as it is no
longer maintained.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:25 +0000 (18:09 +0800)]
configs: P2020RDB: Enable DM_ETH config
Enable the DM_ETH and DM_MDIO config.
On P2020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Mon, 21 Sep 2020 09:46:23 +0000 (15:16 +0530)]
dts: powerpc: p2020rdb: Add eTSEC DT nodes
P2020RDB implements 3 enhanced three-speed Ethernet controllers,
and the connection is shown below:
eTSEC1: Connected to RGMII switch VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:23 +0000 (18:09 +0800)]
configs: P1010RDB: Enable DM_ETH config
Enable the DM_ETH and DM_MDIO config.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Mon, 21 Sep 2020 09:45:04 +0000 (15:15 +0530)]
p1010rdb: Don't compile board_eth_init() for DM_ETH
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Mon, 21 Sep 2020 09:43:22 +0000 (15:13 +0530)]
dts: powerpc: p1010rdb: Add eTSEC DT nodes
P1010RDB implements 3 enhanced three-speed Ethernet controllers,
and the connection is shown below:
eTSEC1: Connected to RGMII PHY AR8033
eTSEC2: Connected to SGMII PHY AR8033
eTSEC3: Connected to SGMII PHY AR8033
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:20 +0000 (18:09 +0800)]
configs: P1020RDB: Enable DM_ETH config
Enable the DM_ETH and DM_MDIO config.
On P1020RDB, the eTSEC1 is connecting with a switch VSC7385,
so also enable the fixed PHY support.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Mon, 21 Sep 2020 09:24:03 +0000 (14:54 +0530)]
p1_p2_rdb: Don't compile board_eth_init() for DM_ETH
The board_eth_init() is only used by legacy ethernet driver framework,
so do not compile it when DM_ETH config has been selected.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Mon, 21 Sep 2020 09:29:05 +0000 (14:59 +0530)]
dts: powerpc: p1020rdb: Add eTSEC DT nodes
P1020RDB implements 3 enhanced three-speed Ethernet controllers,
and the connection is shown below:
eTSEC1: Connected to RGMII switch VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:17 +0000 (18:09 +0800)]
configs: p1_p2_rdb: Add the default address of vsc7385 firmware
Add the environment 'vscfw_addr' to assign a default address for
vsc7385 firmware uploading.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:16 +0000 (18:09 +0800)]
fsl: p1_p2_rdb: Move vsc7835 firmware uploading to board_early_init_r()
Move vsc7835 firmware uploading to board_early_init_r(), so that
the switch also can work in DM eTSEC driver.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Mon, 21 Sep 2020 09:38:45 +0000 (15:08 +0530)]
mpc8xxx: Don't compile board_eth_init() for DM_ETH
The cpu_eth_init() is only used by the legacy ethernet driver framework.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:14 +0000 (18:09 +0800)]
net: tsec: Add the compatible string "gianfar" support
Add compatible string "gianfar" support and update the
device-tree-bindings doc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:13 +0000 (18:09 +0800)]
net: tsec: Add fixed-link PHY support
The info of fixed-link PHY is described in DT node instead of
getting from MII, so detect the fixed-link PHY DT node first,
if it doesn't exist then probe the MII.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:12 +0000 (18:09 +0800)]
net: tsec: convert to use DM_MDIO when DM_ETH enabled
For the platforms on which the eTSEC driver uses DM_ETH, convert its
MDIO controller code to also use DM_MDIO.
Note that for handling the TBI PHY (the MAC PCS for SGMII), we still
don't register a udevice for it, since we can drive it locally and there
is no point in doing otherwise.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Reworked to fix gazerbeam config]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:11 +0000 (18:09 +0800)]
net: fsl_mdio: Correct the MII management register block address
The MII management register block offset is different between
gianfar and etsec2 compatible devices, this patch is to fix
this issue by adding driver data for different compatible
string.
Fixes:
2932c5a802a9 ("net: tsec: fsl_mdio: add DM MDIO support")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 16 Jul 2020 10:09:10 +0000 (18:09 +0800)]
net: fsl_mdio: Change to use virtual address
Use virtual address to access the MII block registers instead
of physical address.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Thu, 16 Jul 2020 10:09:09 +0000 (18:09 +0800)]
configs: enable DM_MDIO for LS1021A-TWR and LS1021A-TSN
The tsec driver now requires DM_MDIO when DM_ETH is enabled. To avoid
build errors, enable DM_MDIO in these boards' configs before we actually
add DM_MDIO support to tsec.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Vladimir Oltean [Thu, 16 Jul 2020 10:09:08 +0000 (18:09 +0800)]
phy: make phy_connect_fixed work with a null mdio bus
It is utterly pointless to require an MDIO bus pointer for a fixed PHY
device. The fixed.c implementation does not require it, only
phy_device_create. Fix that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 4 Jun 2020 15:17:05 +0000 (23:17 +0800)]
configs: P1010RDB: Enable eSPI controller and SPI flash DM driver
Enable the DM_SPI and DM_SPI_FLASH in P1010RDB defconfigs except
SECBOOT defconfigs.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 4 Jun 2020 15:17:04 +0000 (23:17 +0800)]
dts: P1010RDB: Add eSPI slave DT nodes
Add DT nodes for eSPI slave device SPI flash.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Hou Zhiqiang [Thu, 4 Jun 2020 15:17:03 +0000 (23:17 +0800)]
dts: P1010: Add eSPI controller DT node
Add eSPI controller DT node for P1010.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 07:21:19 +0000 (12:51 +0530)]
configs: T4240RDB: Enable ESPI driver
Enable the DM ESPI driver in T4240RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:17:01 +0000 (23:17 +0800)]
dts: T4240RDB: Add ESPI slave device node
Add ESPI slave node for T4240RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:17:00 +0000 (23:17 +0800)]
dts: T4240: Add ESPI DT nodes
Add ESPI controller DT node for T4240.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 07:20:02 +0000 (12:50 +0530)]
configs: T2080RDB: Enable ESPI driver
Enable the DM ESPI driver in T2080RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:58 +0000 (23:16 +0800)]
dts: T2080RDB: Add ESPI slave device node
Add ESPI slave node for T2080RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 07:18:41 +0000 (12:48 +0530)]
configs: T1042D4RDB: Enable ESPI driver
Enable the DM ESPI driver in T1042D4RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:56 +0000 (23:16 +0800)]
dts: T1042D4RDB: Add ESPI slave device node
Add ESPI slave node for T1042D4RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:55 +0000 (23:16 +0800)]
dts: T104x: Add ESPI DT nodes
Add ESPI controller DT node for T104x.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 07:16:54 +0000 (12:46 +0530)]
configs: T1024RDB: Enable ESPI driver
Enable the DM ESPI driver in T1024RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 07:13:20 +0000 (12:43 +0530)]
dts: T1024RDB: Add ESPI slave device node
Add ESPI slave node for T1024RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:52 +0000 (23:16 +0800)]
dts: T102x: Add ESPI DT nodes
Add ESPI controller DT node for T102x.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:51 +0000 (23:16 +0800)]
configs: P5040DS: Enable ESPI driver
Enable the DM ESPI driver in P5040DS defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 07:11:17 +0000 (12:41 +0530)]
dts: P5040DS: Add ESPI slave device node
Add ESPI slave node for P5040DS.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:49 +0000 (23:16 +0800)]
dts: P5040: Add ESPI DT nodes
Add ESPI controller DT node for P5040.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:48 +0000 (23:16 +0800)]
configs: P4080DS: Enable ESPI driver
Enable the DM ESPI driver in P4080DS defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 06:59:04 +0000 (12:29 +0530)]
dts: P4080DS: Add ESPI slave device node
Add ESPI slave node for P4080DS.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:46 +0000 (23:16 +0800)]
dts: P4080: Add ESPI DT nodes
Add ESPI controller DT node for P4080.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:45 +0000 (23:16 +0800)]
configs: P3041DS: Enable ESPI driver
Enable the DM ESPI driver in P3041DS defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 06:56:07 +0000 (12:26 +0530)]
dts: P3041DS: Add ESPI slave device node
Add ESPI slave node for P3041DS.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:43 +0000 (23:16 +0800)]
dts: P3041: Add ESPI DT nodes
Add ESPI controller DT node for P3041.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:42 +0000 (23:16 +0800)]
configs: P2041RDB: Enable ESPI driver
Enable the DM ESPI driver in P2041RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Mon, 21 Sep 2020 06:46:50 +0000 (12:16 +0530)]
dts: P2041RDB: Add ESPI slave device node
Add ESPI slave node for P2041RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:40 +0000 (23:16 +0800)]
dts: P2041: Add ESPI DT nodes
Add ESPI controller DT node for P2041.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:39 +0000 (23:16 +0800)]
configs: P2020RDB: Enable ESPI driver
Enable the DM ESPI driver in P2020RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:38 +0000 (23:16 +0800)]
dts: P2020RDB: Add ESPI slave device node
Add ESPI slave node for P2020RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:37 +0000 (23:16 +0800)]
dts: P2020: Add ESPI DT nodes
Add ESPI controller DT node for P2020.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:36 +0000 (23:16 +0800)]
configs: P1020RDB: Enable ESPI driver
Enable the DM ESPI driver in P1020RDB defconfig.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:35 +0000 (23:16 +0800)]
dts: P1020RDB: Add ESPI slave device node
Add ESPI slave node for P1020RDB.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Xiaowei Bao [Thu, 4 Jun 2020 15:16:34 +0000 (23:16 +0800)]
dts: P1020: Add ESPI DT nodes
Add ESPI controller DT node for P1020.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chuanhua Han [Mon, 21 Sep 2020 06:40:16 +0000 (12:10 +0530)]
configs: enable espi device module in T2080QDS
This patch is to enable espi DM for T2080QDS in uboot
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Chuanhua Han [Thu, 4 Jun 2020 15:16:32 +0000 (23:16 +0800)]
powerpc: dts: t2080qds: add espi slave nodes support
Add espi slave nodes to support t2080qds.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Chuanhua Han [Thu, 4 Jun 2020 15:16:31 +0000 (23:16 +0800)]
powerpc: dts: t2080: add espi controller node support
Add espi controller node to support t2080.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Tom Rini [Tue, 22 Sep 2020 20:59:48 +0000 (16:59 -0400)]
Merge tag 'dm-pull-22sep20' of git://git.denx.de/u-boot-dm into next
binman enhancements for FIT
sunxi64 conversion to use binman
New 'no-map' property for reserved memory
Heinrich Schuchardt [Mon, 14 Sep 2020 08:01:00 +0000 (10:01 +0200)]
log: mute messages generated by log drivers
When a message is written by a log driver (e.g. via the network stack) this
may result in the generation of further messages. We cannot allow these
additional messages to be emitted as this might result in an infinite
recursion.
Up to now only the syslog driver was safeguarded. We should safeguard all
log drivers instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patrick Delaunay [Thu, 10 Sep 2020 16:26:17 +0000 (18:26 +0200)]
dm: add cells_count parameter in live DT APIs of_parse_phandle_with_args
In the live tree API ofnode_parse_phandle_with_args, the cell_count
argument must be used when cells_name is NULL.
But this argument is not provided to the live DT function
of_parse_phandle_with_args even it is provided to
fdtdec_parse_phandle_with_args.
This patch adds support of the cells_count parameter in dev_ and
of_node API to allow migration and support of live DT:
- of_parse_phandle_with_args
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Etienne Carriere [Thu, 10 Sep 2020 08:50:01 +0000 (10:50 +0200)]
optee: add property no-map to secure reserved memory
OP-TEE reserved memory node must set property "no-map" to prevent
Linux kernel from mapping secure memory unless what non-secure world
speculative accesses of the CPU can violate the memory firmware
configuration.
Fixes:
6ccb05eae01b ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Patrice Chotard [Thu, 10 Sep 2020 08:50:00 +0000 (10:50 +0200)]
test: fdtdec: Add test for new no-map fdtdec_add_reserved_memory() parameter
Add a test to verify that the no-map property is added in reserved-memory
node when fdtdec_add_reserved_memory() no-map parameter is set to true.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Etienne Carriere [Thu, 10 Sep 2020 08:49:59 +0000 (10:49 +0200)]
fdtdec: optionally add property no-map to created reserved memory node
Add boolean input argument @no_map to helper function
fdtdec_add_reserved_memory() to add or not "no-map" property
for an added reserved memory node.
Property no-map is used by the Linux kernel to not not map memory
in its static memory mapping. It is needed for example for the|
consistency of system non-cached memory and to prevent speculative
accesses to some firewalled memory.
No functional change. A later change will update to OPTEE library to
add no-map property to OP-TEE reserved memory nodes.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 6 Sep 2020 16:39:10 +0000 (10:39 -0600)]
binman: sunxi: Add help message for missing sunxi ATF BL31
Add a special help message pointing to the relevant README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 6 Sep 2020 16:39:09 +0000 (10:39 -0600)]
binman: Support help messages for missing blobs
When an external blob is missing it can be quite confusing for the user.
Add a way to provide a help message that is shown.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Simon Glass [Sun, 6 Sep 2020 16:39:08 +0000 (10:39 -0600)]
binman: Allow selecting default FIT configuration
Add a new entry argument to the fit entry which allows selection of the
default configuration to use. This is the 'default' property in the
'configurations' node.
Update the Makefile to pass in the value of DEVICE_TREE or
CONFIG_DEFAULT_DEVICE_TREE to provide this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Michal Simek <michal.simek@xilinx.com>
Alper Nebi Yasak [Sun, 6 Sep 2020 11:46:07 +0000 (14:46 +0300)]
binman: Document how CROSS_COMPILE, CC, HOSTCC etc. are used in README
Explain that binman interprets these environment variables in the
"External tools" section to run target/host specific versions of the
tools, and add a new section on how to use CROSS_COMPILE to run the
tests on non-x86 machines.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Sun, 6 Sep 2020 11:46:06 +0000 (14:46 +0300)]
binman: Allow resolving host-specific tools from env vars
This patch lets tools.Run() use host-specific versions with the
for_host keyword argument, based on the host-specific environment
variables (HOSTCC, HOSTOBJCOPY, HOSTSTRIP, etc.).
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Sun, 6 Sep 2020 11:46:05 +0000 (14:46 +0300)]
binman: Use target-specific tools when cross-compiling
Currently, binman always runs the compile tools like cc, objcopy, strip,
etc. using their literal name. Instead, this patch makes it use the
target-specific versions by default, derived from the tool-specific
environment variables (CC, OBJCOPY, STRIP, etc.) or from the
CROSS_COMPILE environment variable.
For example, the u-boot-elf etype directly uses 'strip'. Trying to run
the tests with 'CROSS_COMPILE=i686-linux-gnu- binman test' on an arm64
host results in the '097_elf_strip.dts' test to fail as the arm64
version of 'strip' can't understand the format of the x86 ELF file.
This also adjusts some command.Output() calls that caused test errors or
failures to use the target versions of the tools they call. After this,
patch, an arm64 host can run all tests with no errors or failures using
a correct CROSS_COMPILE value.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Sun, 6 Sep 2020 11:46:04 +0000 (14:46 +0300)]
binman: Support cross-compiling test files to x86
These test files are currently "intended for use on x86 hosts", but most
of the tests using them can still pass when cross-compiled to x86 on an
arm64 host.
This patch enables non-x86 hosts to run the tests by specifying a
cross-compiler via CROSS_COMPILE. The list of variables it sets is taken
from the top-level Makefile. It would be possible to automatically set
an x86 cross-compiler with a few blocks like:
ifneq ($(shell i386-linux-gnu-gcc --version 2> /dev/null),)
CROSS_COMPILE = i386-linux-gnu-
endif
But it wouldn't propagate to the binman process calling this Makefile,
so it's better just raise an error and expect 'binman test' to be run
with a correct CROSS_COMPILE.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Heinrich Schuchardt [Sat, 22 Aug 2020 05:16:26 +0000 (07:16 +0200)]
dm: syscon: typo alerady
* Fix typo: %s/alerady/already/.
* Add missing 'the'.
* Reformat a comment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Alper Nebi Yasak [Thu, 3 Sep 2020 12:51:03 +0000 (15:51 +0300)]
buildman: Use git worktrees instead of git clones when possible
This patch makes buildman create linked working trees instead of clones
of the source repository, but keeps updating the older clones of the
repository that might already exist. These worktrees share "everything
except working directory specific files such as HEAD, index, etc." with
the source repository. See the git-worktree(1) manual page for more
information.
If git-worktree isn't available, silently falls back to cloning the
repository.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:14:02 +0000 (05:14 -0600)]
sunxi: Drop the FIT-generator script
This file is no-longer used. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:14:01 +0000 (05:14 -0600)]
sunxi: Convert 64-bit boards to use binman
At present 64-bit sunxi boards use the Makefile to create a FIT, using
USE_SPL_FIT_GENERATOR. This is deprecated.
Update sunxi to use binman instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Glass [Tue, 1 Sep 2020 11:14:00 +0000 (05:14 -0600)]
Makefile: Support missing external blobs always
At present binman warns about missing external blobs only when the
BUILD_ROM is defined. Enable this behaviour always, since many boards
are starting to use these (e.g. ARM Trusted Firmware's BL31).
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:13:59 +0000 (05:13 -0600)]
binman: Support generating FITs with multiple dtbs
In some cases it is useful to generate a FIT which has a number of DTB
images, selectable by configuration. Add support for this in binman,
using a simple iterator and string substitution.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:13:58 +0000 (05:13 -0600)]
binman: Add support for ATF BL31
Add an entry for ARM Trusted Firmware's 'BL31' payload, which is the
device's main firmware. Typically this is U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:13:57 +0000 (05:13 -0600)]
binman: Move 'external' support into base class
At present we have an Entry_blob_ext which implement a blob which holds an
external binary. We need to support other entry types that hold external
binaries, e.g. Entry_blob_named_by_arg. Move the support into the base
Entry class to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:13:56 +0000 (05:13 -0600)]
libfdt: Detected out-of-space with fdt_finish()
At present the Python sequential-write interface can produce an error when
it calls fdt_finish(), since this needs to add a terminating tag to the
end of the struct section.
Fix this by automatically expanding the buffer if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:13:55 +0000 (05:13 -0600)]
binman: Fix up a few missing comments
Tidy up a few test functions which lack argument comments. Rename one that
has the same name as a different test.
Also fix up the comment for PrepareImagesAndDtbs().
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Tue, 1 Sep 2020 11:13:54 +0000 (05:13 -0600)]
binman: Allow entry args to be required
If an entry argument is needed by an entry but the entry argument is not
present, then a strange error can occur when trying to read the file.
Fix this by allowing arguments to be required. Select this option for the
cros-ec-rw entry. If a filename is provided in the node, allow that to be
used.
Also tidy up a few related tests to make the error string easier to find,
and fully ignore unused return values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Walter Lozano [Wed, 29 Jul 2020 16:17:31 +0000 (13:17 -0300)]
core: improve of_match_ptr with OF_PLATDATA
Currently of_match_ptr is used to avoid referencing compatible strings
when OF_CONTROL is not enabled. This behaviour could be improved by
taking into account also OF_PLATDATA, as when this configuration is
enabled the compatible strings are not used at all.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
projects / platform / kernel / u-boot.git / log