Badhri Jagan Sridharan [Thu, 8 Oct 2020 06:15:45 +0000 (23:15 -0700)]
usb: typec: tcpci_maxim: Chip level TCPC driver
Chip level TCPC driver for Maxim's TCPCI implementation.
This TCPC implementation does not support the following
commands: COMMAND.SinkVbus, COMMAND.SourceVbusDefaultVoltage,
COMMAND.SourceVbusHighVoltage. Instead the sinking and sourcing
from vbus is supported by writes to custom registers.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-5-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Badhri Jagan Sridharan [Thu, 8 Oct 2020 06:15:43 +0000 (23:15 -0700)]
usb: typec: tcpci: Add set_vbus tcpci callback
set_vbus callback allows TCPC which are TCPCI based, however,
does not support turning on sink and source mode through
Command.SinkVbus and Command.SourceVbusDefaultVoltage.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Badhri Jagan Sridharan [Thu, 8 Oct 2020 06:15:42 +0000 (23:15 -0700)]
usb: typec: tcpci: Add a getter method to retrieve tcpm_port reference
Allow chip level drivers to retrieve reference to tcpm_port.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-2-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shuah Khan [Tue, 6 Oct 2020 22:39:14 +0000 (16:39 -0600)]
usbip: vhci_hcd: fix calling usb_hcd_giveback_urb() with irqs enabled
kcov testing uncovered call to usb_hcd_giveback_urb() without disabling
interrupts.
Link: https://lore.kernel.org/linux-usb/CAAeHK+wb4k-LGTjK9F5YbJNviF_+yU+wE_=Vpo9Rn7KFN8vG6Q@mail.gmail.com/
usb_hcd_giveback_urb() is called from vhci's urb_enqueue, when it
determines it doesn't need to xmit the urb and can give it back.
This path runs in task context.
Disable irqs around usb_hcd_giveback_urb() call.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20201006223914.39257-1-skhan@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Vincent Mailhol [Fri, 2 Oct 2020 15:41:51 +0000 (00:41 +0900)]
usb: cdc-acm: add quirk to blacklist ETAS ES58X devices
The ES58X devices has a CDC ACM interface (used for debug
purpose). During probing, the device is thus recognized as USB Modem
(CDC ACM), preventing the etas-es58x module to load:
usbcore: registered new interface driver etas_es58x
usb 1-1.1: new full-speed USB device number 14 using xhci_hcd
usb 1-1.1: New USB device found, idVendor=108c, idProduct=0159, bcdDevice= 1.00
usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1.1: Product: ES581.4
usb 1-1.1: Manufacturer: ETAS GmbH
usb 1-1.1: SerialNumber: 2204355
cdc_acm 1-1.1:1.0: No union descriptor, testing for castrated device
cdc_acm 1-1.1:1.0: ttyACM0: USB ACM device
Thus, these have been added to the ignore list in
drivers/usb/class/cdc-acm.c
N.B. Future firmware release of the ES58X will remove the CDC-ACM
interface.
`lsusb -v` of the three devices variant (ES581.4, ES582.1 and
ES584.1):
Bus 001 Device 011: ID 108c:0159 Robert Bosch GmbH ES581.4
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0159
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES581.4
iSerial 3 2204355
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0035
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 5 Bus Powered Configuration
bmAttributes 0x80
(Bus Powered)
MaxPower 100mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 0
iInterface 4 ACM Control Interface
CDC Header:
bcdCDC 1.10
CDC Call Management:
bmCapabilities 0x01
call management
bDataInterface 0
CDC ACM:
bmCapabilities 0x06
sends break
line coding and serial state
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 10
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 012: ID 108c:0168 Robert Bosch GmbH ES582
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0168
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES582
iSerial 3 0108933
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Bus 001 Device 013: ID 108c:0169 Robert Bosch GmbH ES584.1
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x108c Robert Bosch GmbH
idProduct 0x0169
bcdDevice 1.00
iManufacturer 1 ETAS GmbH
iProduct 2 ES584.1
iSerial 3 0100320
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 0x0043
bNumInterfaces 2
bConfigurationValue 1
iConfiguration 0
bmAttributes 0x80
(Bus Powered)
MaxPower 500mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 2 Communications
bInterfaceSubClass 2 Abstract (modem)
bInterfaceProtocol 1 AT-commands (v.25ter)
iInterface 0
CDC Header:
bcdCDC 1.10
CDC ACM:
bmCapabilities 0x02
line coding and serial state
CDC Union:
bMasterInterface 0
bSlaveInterface 1
CDC Call Management:
bmCapabilities 0x03
call management
use DataInterface
bDataInterface 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 16
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 10 CDC Data
bInterfaceSubClass 0
bInterfaceProtocol 0
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 2 Communications
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0000
(Bus Powered)
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201002154219.4887-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Mon, 5 Oct 2020 06:54:36 +0000 (08:54 +0200)]
Merge 5.9-rc8 into usb-next
We need the USB fixes in here as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Sun, 4 Oct 2020 23:04:34 +0000 (16:04 -0700)]
Linux 5.9-rc8
Linus Torvalds [Sat, 3 Oct 2020 19:19:23 +0000 (12:19 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"Two bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF intercept
KVM: arm64: Restore missing ISB on nVHE __tlb_switch_to_guest
Linus Torvalds [Sat, 3 Oct 2020 18:57:39 +0000 (11:57 -0700)]
Merge tag 'for-linus-5.9b-rc8-tag' of git://git./linux/kernel/git/xen/tip
Pull xen fix from Juergen Gross:
"Fix a regression introduced in 5.9-rc3 which caused a system running
as fully virtualized guest under Xen to crash when using legacy
devices like a floppy"
* tag 'for-linus-5.9b-rc8-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't use chip_data for legacy IRQs
Linus Torvalds [Sat, 3 Oct 2020 18:47:35 +0000 (11:47 -0700)]
Merge tag 'usb-5.9-rc8' of git://git./linux/kernel/git/gregkh/usb
Pull USB/PHY fixes from Greg KH:
"Here are some small USB and PHY driver fixes for 5.9-rc8
The PHY driver fix resolves an issue found by Dan Carpenter for a
memory leak.
The USB fixes fall into two groups:
- usb gadget fix from Bryan that is a fix for a previous security fix
that showed up in in-the-wild testing
- usb core driver matching bugfixes. This fixes a bug that has
plagued the both the usbip driver and syzbot testing tools this -rc
release cycle. All is now working properly so usbip connections
will work, and syzbot can get back to fuzzing USB drivers properly.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usbcore/driver: Accommodate usbip
usbcore/driver: Fix incorrect downcast
usbcore/driver: Fix specific driver selection
Revert "usbip: Implement a match function to fix usbip"
USB: gadget: f_ncm: Fix NDP16 datagram validation
phy: ti: am654: Fix a leak in serdes_am654_probe()
Linus Torvalds [Sat, 3 Oct 2020 18:40:22 +0000 (11:40 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Some more driver fixes for i2c"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: npcm7xx: Clear LAST bit after a failed transaction.
i2c: cpm: Fix i2c_ram structure
i2c: i801: Exclude device from suspend direct complete optimization
Linus Torvalds [Sat, 3 Oct 2020 18:37:23 +0000 (11:37 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A couple more driver quirks, now enabling newer trackpoints from
Synaptics for real"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: i8042 - add nopnp quirk for Acer Aspire 5 A515
Input: trackpoint - enable Synaptics trackpoints
Eric Biggers [Sat, 3 Oct 2020 05:21:48 +0000 (22:21 -0700)]
scripts/spelling.txt: fix malformed entry
One of the entries has three fields "mistake||correction||correction"
rather than the expected two fields "mistake||correction". Fix it.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Link: https://lkml.kernel.org/r/20200930234359.255295-1-ebiggers@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joonsoo Kim [Sat, 3 Oct 2020 05:21:45 +0000 (22:21 -0700)]
mm/page_alloc: handle a missing case for memalloc_nocma_{save/restore} APIs
memalloc_nocma_{save/restore} APIs can be used to skip page allocation
on CMA area, but, there is a missing case and the page on CMA area could
be allocated even if APIs are used. This patch handles this case to fix
the potential issue.
For now, these APIs are used to prevent long-term pinning on the CMA
page. When the long-term pinning is requested on the CMA page, it is
migrated to the non-CMA page before pinning. This non-CMA page is
allocated by using memalloc_nocma_{save/restore} APIs. If APIs doesn't
work as intended, the CMA page is allocated and it is pinned for a long
time. This long-term pin for the CMA page causes cma_alloc() failure
and it could result in wrong behaviour on the device driver who uses the
cma_alloc().
Missing case is an allocation from the pcplist. MIGRATE_MOVABLE pcplist
could have the pages on CMA area so we need to skip it if ALLOC_CMA
isn't specified.
Fixes:
8510e69c8efe (mm/page_alloc: fix memalloc_nocma_{save/restore} APIs)
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Aneesh Kumar K . V" <aneesh.kumar@linux.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Link: https://lkml.kernel.org/r/1601429472-12599-1-git-send-email-iamjoonsoo.kim@lge.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Farman [Sat, 3 Oct 2020 05:21:41 +0000 (22:21 -0700)]
mm, slub: restore initial kmem_cache flags
The routine that applies debug flags to the kmem_cache slabs
inadvertantly prevents non-debug flags from being applied to those
same objects. That is, if slub_debug=<flag>,<slab> is specified,
non-debugged slabs will end up having flags of zero, and the slabs
may be unusable.
Fix this by including the input flags for non-matching slabs with the
contents of slub_debug, so that the caches are created as expected
alongside any debugging options that may be requested. With this, we
can remove the check for a NULL slub_debug_string, since it's covered
by the loop itself.
Fixes:
e17f1dfba37b ("mm, slub: extend slub_debug syntax for multiple blocks")
Signed-off-by: Eric Farman <farman@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Kees Cook <keescook@chromium.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Link: https://lkml.kernel.org/r/20200930161931.28575-1-farman@linux.ibm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Greg Kroah-Hartman [Sat, 3 Oct 2020 13:59:57 +0000 (15:59 +0200)]
Merge tag 'usb-for-v5.10' of git://git./linux/kernel/git/balbi/usb into usb-next
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
Paolo Bonzini [Sat, 3 Oct 2020 09:07:59 +0000 (05:07 -0400)]
Merge tag 'kvmarm-fixes-5.9-3' of git://git./linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/arm64 fixes for 5.9, take #3
- Fix synchronization of VTTBR update on TLB invalidation for nVHE systems
Paolo Bonzini [Tue, 29 Sep 2020 12:31:32 +0000 (08:31 -0400)]
KVM: VMX: update PFEC_MASK/PFEC_MATCH together with PF intercept
The PFEC_MASK and PFEC_MATCH fields in the VMCS reverse the meaning of
the #PF intercept bit in the exception bitmap when they do not match.
This means that, if PFEC_MASK and/or PFEC_MATCH are set, the
hypervisor can get a vmexit for #PF exceptions even when the
corresponding bit is clear in the exception bitmap.
This is unexpected and is promptly detected by a WARN_ON_ONCE.
To fix it, reset PFEC_MASK and PFEC_MATCH when the #PF intercept
is disabled (as is common with enable_ept && !allow_smaller_maxphyaddr).
Reported-by: Qian Cai <cai@redhat.com>>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Linus Torvalds [Fri, 2 Oct 2020 21:51:34 +0000 (14:51 -0700)]
Merge tag 'pinctrl-v5.9-2' of git://git./linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"Some pin control fixes here. All of them are driver fixes, the Intel
Cherryview being the most interesting one.
- Fix a mux problem for I2C in the MVEBU driver.
- Fix a really hairy inversion problem in the Intel Cherryview
driver.
- Fix the register for the sdc2_clk in the Qualcomm SM8250 driver.
- Check the virtual GPIO boot failur in the Mediatek driver"
* tag 'pinctrl-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: mediatek: check mtk_is_virt_gpio input parameter
pinctrl: qcom: sm8250: correct sdc2_clk
pinctrl: cherryview: Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
pinctrl: mvebu: Fix i2c sda definition for 98DX3236
Linus Torvalds [Fri, 2 Oct 2020 21:48:25 +0000 (14:48 -0700)]
Merge tag 'pci-v5.9-fixes-2' of git://git./linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Fix rockchip regression in rockchip_pcie_valid_device() (Lorenzo
Pieralisi)
- Add Pali Rohár as aardvark PCI maintainer (Pali Rohár)
* tag 'pci-v5.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Add Pali Rohár as aardvark PCI maintainer
PCI: rockchip: Fix bus checks in rockchip_pcie_valid_device()
Linus Torvalds [Fri, 2 Oct 2020 21:42:13 +0000 (14:42 -0700)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two patches in driver frameworks. The iscsi one corrects a bug induced
by a BPF change to network locking and the other is a regression we
introduced"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: iscsi_tcp: Avoid holding spinlock while calling getpeername()
scsi: target: Fix lun lookup for TARGET_SCF_LOOKUP_LUN_FROM_TAG case
Linus Torvalds [Fri, 2 Oct 2020 21:38:10 +0000 (14:38 -0700)]
Merge tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- fix for async buffered reads if read-ahead is fully disabled (Hao)
- double poll match fix
- ->show_fdinfo() potential ABBA deadlock complaint fix
* tag 'io_uring-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
io_uring: fix async buffered reads when readahead is disabled
io_uring: fix potential ABBA deadlock in ->show_fdinfo()
io_uring: always delete double poll wait entry on match
Linus Torvalds [Fri, 2 Oct 2020 21:34:52 +0000 (14:34 -0700)]
Merge tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block
Pull block fix from Jens Axboe:
"Single fix for a ->commit_rqs failure case"
* tag 'block-5.9-2020-10-02' of git://git.kernel.dk/linux-block:
blk-mq: call commit_rqs while list empty but error happen
Linus Torvalds [Fri, 2 Oct 2020 17:37:08 +0000 (10:37 -0700)]
Merge branch 'work.epoll' of git://git./linux/kernel/git/viro/vfs
Pull epoll fixes from Al Viro:
"Several race fixes in epoll"
* 'work.epoll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
ep_create_wakeup_source(): dentry name can change under you...
epoll: EPOLL_CTL_ADD: close the race in decision to take fast path
epoll: replace ->visited/visited_list with generation count
epoll: do not insert into poll queues until all sanity checks are done
Linus Torvalds [Fri, 2 Oct 2020 17:13:05 +0000 (10:13 -0700)]
Merge tag 'riscv-for-linus-5.9-rc8' of git://git./linux/kernel/git/riscv/linux
Pull RISC-V fixes from Palmer Dabbelt:
"Two fixes for this week:
- The addition of a symbol export for clint_time_val, which has been
inlined into some timex functions and can be used by drivers.
- A fix to avoid calling get_cycles() before the timers have been
probed.
These both only effect !MMU systems"
* tag 'riscv-for-linus-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
RISC-V: Check clint_time_val before use
clocksource: clint: Export clint_time_val for modules
Linus Torvalds [Fri, 2 Oct 2020 17:09:40 +0000 (10:09 -0700)]
Merge tag 'for-5.9-rc7-tag' of git://git./linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
"Two more fixes.
One is for a lockdep warning/lockup (also caught by syzbot), that one
has been seen in practice. Regarding the other syzbot reports
mentioned last time, they don't seem to be urgent and reliably
reproducible so they'll be fixed later.
The second fix is for a potential corruption when device replace
finishes and the in-memory state of trim is not copied to the new
device"
* tag 'for-5.9-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: fix filesystem corruption after a device replace
btrfs: move btrfs_rm_dev_replace_free_srcdev outside of all locks
btrfs: move btrfs_scratch_superblocks into btrfs_dev_replace_finishing
Linus Torvalds [Fri, 2 Oct 2020 17:05:56 +0000 (10:05 -0700)]
Merge tag 'pm-5.9-rc8' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix one more issue related to the recent RCU-lockdep changes, a
typo in documentation and add a missing return statement to
intel_pstate.
Specifics:
- Fix up RCU usage for cpuidle on the ARM imx6q platform (Ulf
Hansson)
- Fix typo in the PM documentation (Yoann Congal)
- Add return statement that is missing after recent changes in the
intel_pstate driver (Zhang Rui)"
* tag 'pm-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ARM: imx6q: Fixup RCU usage for cpuidle
Documentation: PM: Fix a reStructuredText syntax error
cpufreq: intel_pstate: Fix missing return statement
Linus Torvalds [Fri, 2 Oct 2020 17:01:00 +0000 (10:01 -0700)]
Merge tag 'staging-5.9-rc8' of git://git./linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are two small IIO driver fixes for 5.9-rc8 that resolve some
reported issues:
- driver name fixed in one driver
- device name typo fixed
Both have been in linux-next for a while with no reported problems"
* tag 'staging-5.9-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: qcom-spmi-adc5: fix driver name
iio: adc: ad7124: Fix typo in device name
Linus Torvalds [Fri, 2 Oct 2020 16:51:42 +0000 (09:51 -0700)]
Merge tag 'gpio-v5.9-2' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
Linus Torvalds [Fri, 2 Oct 2020 16:40:09 +0000 (09:40 -0700)]
Merge tag 'mmc-v5.9-rc4-3' of git://git./linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- Fix deadlock when removing MEMSTICK host
- Workaround broken CMDQ on Intel GLK based IRBIS models
* tag 'mmc-v5.9-rc4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci: Workaround broken command queuing on Intel GLK based IRBIS models
memstick: Skip allocating card when removing host
Thibaut Sautereau [Fri, 2 Oct 2020 15:16:11 +0000 (17:16 +0200)]
random32: Restore __latent_entropy attribute on net_rand_state
Commit
f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") broke compilation and was temporarily fixed by Linus in
83bdc7275e62 ("random32: remove net_rand_state from the latent entropy
gcc plugin") by entirely moving net_rand_state out of the things handled
by the latent_entropy GCC plugin.
From what I understand when reading the plugin code, using the
__latent_entropy attribute on a declaration was the wrong part and
simply keeping the __latent_entropy attribute on the variable definition
was the correct fix.
Fixes:
83bdc7275e62 ("random32: remove net_rand_state from the latent entropy gcc plugin")
Acked-by: Willy Tarreau <w@1wt.eu>
Cc: Emese Revfy <re.emese@gmail.com>
Signed-off-by: Thibaut Sautereau <thibaut.sautereau@ssi.gouv.fr>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rafael J. Wysocki [Fri, 2 Oct 2020 16:30:30 +0000 (18:30 +0200)]
Merge branch 'pm-cpufreq'
* pm-cpufreq:
cpufreq: intel_pstate: Fix missing return statement
Roman Gushchin [Thu, 1 Oct 2020 20:07:49 +0000 (13:07 -0700)]
mm: memcg/slab: fix slab statistics in !SMP configuration
Since commit
ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat
items") the write side of slab counters accepts a value in bytes and
converts it to pages. It happens in __mod_node_page_state().
However a non-SMP version of __mod_node_page_state() doesn't perform
this conversion. It leads to incorrect (unrealistically high) slab
counters values. Fix this by adding a similar conversion to the non-SMP
version of __mod_node_page_state().
Signed-off-by: Roman Gushchin <guro@fb.com>
Reported-and-tested-by: Bastian Bittorf <bb@npl.de>
Fixes:
ea426c2a7de8 ("mm: memcg: prepare for byte-sized vmstat items")
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sergey Korolev [Sun, 9 Aug 2020 16:12:30 +0000 (19:12 +0300)]
USB: core: remove polling for /sys/kernel/debug/usb/devices
The latest reference to usbfs_conn_disc_event() removed in
commit
fb28d58b72aa ("USB: remove CONFIG_USB_DEVICEFS")
in 2012 and now a user poll() waits infinitely for content changes.
Signed-off-by: Sergey Korolev <s.korolev@ndmsystems.com>
Link: https://lore.kernel.org/r/20200809161233.13135-1-s.korolev@ndmsystems.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amelie Delaunay [Thu, 24 Sep 2020 09:00:47 +0000 (11:00 +0200)]
usb: typec: add support for STUSB160x Type-C controller family
STMicroelectronics USB Type-C port controllers use I2C interface to
configure, control and read the operation status of the device. All ST USB
Type-C port controllers are based on the same I2C register map. That's why
this driver can be used with all ST USB Type-C ICs.
Some ST USB Type-C port controllers are Dual Role Port (DRP), only Sink or
Source, some supports USB Power Delivery. This can be configured through
connector device tree bindings.
This driver is a basic Type-C port controller driver, with no power
delivery support. It allows to configure ST USB Type-C port controller.
Interrupt is supported and enables CC connection events, to detect
attach and detach and update Type-C subsystem accordingly as well as usb
role switch.
ST USB Type-C port controller can be supplied in three different ways
depending on the target application:
- through VDD pin only (so VDD is the main supply)
- through VSYS pin only (so VSYS is the main supply)
- through VDD and VSYS pins.
When both VDD and VSYS power supplies are present, the low power supply
VSYS is selected as main supply when VSYS voltage is above 3.1V, else
VDD is selected as main supply.
In case of Source or Dual port type, if VDD supply is present, it has to be
enabled in case of Source power role to provide Vbus. When interrupt
support is available, VDD supply is dynamically managed upon attach/detach
interrupt. When there is no interrupt support, VDD supply is enabled by
default.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-5-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Amelie Delaunay [Thu, 24 Sep 2020 09:00:45 +0000 (11:00 +0200)]
usb: typec: add typec_find_pwr_opmode
This patch adds a function that converts power operation mode string into
power operation mode value.
It is useful to configure power operation mode through device tree
property, as power capabilities may be linked to hardware design.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Link: https://lore.kernel.org/r/20200924090049.9041-3-amelie.delaunay@st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Biju Das [Sun, 20 Sep 2020 13:49:03 +0000 (14:49 +0100)]
usb: typec: hd3ss3220: Use OF graph API to get the connector fwnode
Some platforms have only super speed data bus connected to this device
and high speed data bus directly connected to the SoC. In such platforms
modelling connector as a child of this device is making it non compliant
with usb connector bindings. By modelling connector node as standalone
device node along with this device and the SoC data bus will make it
compliant with usb connector bindings.
Update the driver to handle this model by using OF graph API to get the
connector fwnode and usb role switch class API to get role switch handle.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200920134905.4370-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Biju Das [Sun, 20 Sep 2020 13:49:02 +0000 (14:49 +0100)]
dt-bindings: usb: renesas,usb3-peri: Document HS and SS data bus
Document HS and SS data bus for the "usb-role-switch" enabled case.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200920134905.4370-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lad Prabhakar [Sun, 20 Sep 2020 13:49:01 +0000 (14:49 +0100)]
dt-bindings: usb: convert ti,hd3ss3220 bindings to json-schema
Convert ti,hd3ss3220.txt to YAML. Updated the binding documentation
as graph bindings of this device model Super Speed (SS) data bus to
the Super Speed (SS) capable connector.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20200920134905.4370-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Greg Kroah-Hartman [Fri, 2 Oct 2020 11:45:00 +0000 (13:45 +0200)]
Merge tag 'phy-for-5.10' of git://git./linux/kernel/git/phy/linux-phy into usb-next
Vinod writes:
phy for 5.9
- Core:
- New PHY attribute for max_link_rate
- New phy drivers:
- Rockchip dphy driver moved from staging
- Socionext UniPhier AHCI PHY driver
- Intel LGM SoC USB phy
- Intel Keem Bay eMMC PHY driver
- Updates:
- Support for imx8mp usb phy
- Support for DP Phy and USB3+DP combo phy in QMP driver
- Support for Qualcomm sc7180 DP phy
- Support for cadence torrent PCIe and USB single linke and multilink
configurations along with USB, SGMII/QSGMII configurations
* tag 'phy-for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (72 commits)
phy: qcom-qmp: initialize the pointer to NULL
phy: qcom-qmp: Add support for sc7180 DP phy
phy: qcom-qmp: Add support for DP in USB3+DP combo phy
phy: qcom-qmp: Use devm_platform_ioremap_resource() to simplify
phy: qcom-qmp: Get dp_com I/O resource by index
phy: qcom-qmp: Move 'serdes' and 'cfg' into 'struct qcom_phy'
phy: qcom-qmp: Remove 'initialized' in favor of 'init_count'
phy: qcom-qmp: Move phy mode into struct qmp_phy
dt-bindings: phy: qcom,qmp-usb3-dp: Add DP phy information
dt-bindings: phy: ti,phy-j721e-wiz: fix bindings for torrent phy
dt-bindings: phy: cdns,torrent-phy: add reset-names
phy: rockchip-dphy-rx0: Include linux/delay.h
phy: fix USB_LGM_PHY warning & build errors
phy: cadence-torrent: Add USB + SGMII/QSGMII multilink configuration
phy: cadence-torrent: Add PCIe + USB multilink configuration
phy: cadence-torrent: Add single link USB register sequences
phy: cadence-torrent: Add single link SGMII/QSGMII register sequences
phy: cadence-torrent: Configure PHY_PLL_CFG as part of link_cmn_vals
phy: cadence-torrent: Add PHY link configuration sequences for single link
phy: cadence-torrent: Add clk changes for multilink configuration
...
Minas Harutyunyan [Thu, 24 Sep 2020 14:08:39 +0000 (18:08 +0400)]
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.
Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.
In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.
Fixes:
cf77b5fb9b394 ("usb: dwc2: gadget: Transfer length limit checking for DDMA")
Fixes:
e02f9aa6119e0 ("usb: dwc2: gadget: EP 0 specific DDMA programming")
Fixes:
aa3e8bc81311e ("usb: dwc2: gadget: DDMA transfer start and complete")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Amelie Delaunay [Wed, 9 Sep 2020 09:35:11 +0000 (11:35 +0200)]
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
If usb-role-switch is present in the device tree, it means that ID and Vbus
signals are not connected to the OTG controller but to an external
component (GPIOs, Type-C controller). In this configuration, usb role
switch is used to force valid sessions on STM32MP15 SoCs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Amelie Delaunay [Wed, 9 Sep 2020 09:35:10 +0000 (11:35 +0200)]
usb: dwc2: override PHY input signals with usb role switch support
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Amelie Delaunay [Wed, 9 Sep 2020 09:35:09 +0000 (11:35 +0200)]
dt-bindings: usb: dwc2: add optional usb-role-switch property
This patch documents the usb-role-switch property in dwc2 bindings, now
that usb-role-switch support is available in dwc2 driver.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Wan Ahmad Zainie [Mon, 21 Sep 2020 02:44:59 +0000 (10:44 +0800)]
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
Add compatible string to use this generic glue layer to support
Intel Keem Bay platform's dwc3 controller.
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Wan Ahmad Zainie [Mon, 21 Sep 2020 02:44:58 +0000 (10:44 +0800)]
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
Binding description for Intel Keem Bay USB controller.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Tue, 29 Sep 2020 22:26:29 +0000 (15:26 -0700)]
usb: dwc3: gadget: Support up to max stream id
DWC3 IPs can use the maximum stream id (up to 2^16) specified by the
USB 3.x specs. Don't limit to stream id 2^15 only. Note that this does
not reflect the number of concurrent streams the controller handles
internally.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Oliver Neukum [Mon, 28 Sep 2020 14:17:55 +0000 (23:17 +0900)]
USB: cdc-wdm: Make wdm_flush() interruptible and add wdm_fsync().
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=
e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/
27b7545e-8f41-10b8-7c02-
e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/
79ba410f-e0ef-2465-b94f-
6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/
20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/
c85331fc-874c-6e46-a77f-
0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petko Manolov [Sun, 27 Sep 2020 12:49:08 +0000 (15:49 +0300)]
net: pegasus: Use the new usb control message API.
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Added small note about why set_registers() can't be used to substitute
set_register().
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-2-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Petko Manolov [Sun, 27 Sep 2020 12:49:09 +0000 (15:49 +0300)]
net: rtl8150: Use the new usb control message API.
The old usb_control_msg() let the caller handle the error and also did not
account for partial reads. Since these are now considered harmful, move the
driver over to usb_control_msg_recv/send() calls.
Signed-off-by: Petko Manolov <petko.manolov@konsulko.com>
Acked-by: David S. Miller <davem@davemloft.net>
Link: https://lore.kernel.org/r/20200927124909.16380-3-petko.manolov@konsulko.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Heikki Krogerus [Mon, 28 Sep 2020 13:33:24 +0000 (16:33 +0300)]
usb: typec: displayport: Reduce noise from the driver
It's not an error if the mode can't be entered because
another mode is already active, so no longer printing an
error message if that happens.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200928133324.48841-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 28 Sep 2020 15:22:17 +0000 (11:22 -0400)]
USB: hub: Add Kconfig option to reduce number of port initialization retries
Description based on one by Yasushi Asano:
According to 6.7.22 A-UUT “Device No Response” for connection timeout
of USB OTG and EH automated compliance plan v1.2, enumeration failure
has to be detected within 30 seconds. However, the old and new
enumeration schemes each make a total of 12 attempts, and each attempt
can take 5 seconds to time out, so the PET test fails.
This patch adds a new Kconfig option (CONFIG_USB_FEW_INIT_RETRIES);
when the option is set all the initialization retry loops except the
outermost are reduced to a single iteration. This reduces the total
number of attempts to four, allowing Linux hosts to pass the PET test.
The new option is disabled by default to preserve the existing
behavior. The reduced number of retries may fail to initialize a few
devices that currently do work, but for the most part there should be
no change. And in cases where the initialization does fail, it will
fail much more quickly.
Reported-and-tested-by: yasushi asano <yazzep@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152217.GB134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alan Stern [Mon, 28 Sep 2020 15:20:50 +0000 (11:20 -0400)]
USB: hub: Clean up use of port initialization schemes and retries
The SET_CONFIG_TRIES macro in hub.c is badly named; it controls the
number of port-initialization retry attempts rather than the number of
Set-Configuration attempts. Furthermore, the USE_NEW_SCHEME macro and
use_new_scheme() function are written in a very confusing manner,
making it almost impossible to figure out exactly what they do or
check that they are correct.
This patch renames SET_CONFIG_TRIES to PORT_INIT_TRIES, removes
USE_NEW_SCHEME entirely, and rewrites use_new_scheme() to be much more
transparent, with added comments explaining how it works. The patch
also pulls the single call site of use_new_scheme() out from the
Get-Descriptor retry loop (where it returns the same value each time)
and renames the local variable used to store the result.
The overall effect is a minor cleanup. However, there is one
functional change: If the "use_both_schemes" module parameter isn't
set (by default it is set), the existing code does only two retry
iterations. After this patch it will always perform four, regardless
of the parameter's value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928152050.GA134701@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Thinh Nguyen [Thu, 1 Oct 2020 00:44:38 +0000 (17:44 -0700)]
usb: dwc3: gadget: Return early if no TRB update
If the transfer had already started and there's no TRB to update, then
there's no need to go through __dwc3_gadget_kick_transfer(). There is
no problem reissuing UPDATE_TRANSFER command. This change just saves
the driver from doing a few operations. This happens when we run out of
TRB and function driver still queues for more requests.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 1 Oct 2020 00:44:32 +0000 (17:44 -0700)]
usb: dwc3: gadget: Keep TRBs in request order
If we couldn't finish preparing all the TRBs of a request, don't prepare
the next request. Otherwise, the TRBs order will be mixed up and the
controller will process the wrong TRB. This is a corner case where
there's not enough TRBs for a request that needs the extra TRB but
there's still 1 available TRB in the pool.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 1 Oct 2020 00:44:25 +0000 (17:44 -0700)]
usb: dwc3: gadget: Revise setting IOC when no TRB left
To keep the setting of interrupt-on-completion (IOC) when out of TRBs
consistent and easier to read, the caller of dwc3_prepare_one_trb()
will determine if the TRB must have IOC bit set. This also reduces the
number of times we need to call dwc3_calc_trbs_left(). Note that we only
care about setting IOC from insufficient number of TRBs for SG and not
linear requests (because we don't need to split linear requests).
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 1 Oct 2020 00:44:19 +0000 (17:44 -0700)]
usb: dwc3: gadget: Look ahead when setting IOC
Previously if we run out of TRBs for the last SG entry that requires
an extra TRB, we set interrupt-on-completion (IOC) bit to an already
prepared TRB (i.e. HWO=1). This logic is not clean, and it's not a
typical way to prepare TRB. Also, this prevents showing IOC setup in
tracepoint when __dwc3_prepare_one_trb() is executed. Instead, let's
look ahead when preparing TRB to know whether to set the IOC bit before
the last SG entry. This requires adding a new parameter "must_interrupt"
to dwc3_prepare_one_trb().
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Tue, 29 Sep 2020 07:18:48 +0000 (00:18 -0700)]
usb: dwc3: gadget: Allow restarting a transfer
It's possible that there's no new TRBs prepared when kicking a transfer.
This happens when we need to stop and restart a transfer such as in the
case of reinitiating a stream or retrying isoc transfer. For streams,
sometime host may reject a stream and the device may need to reinitiate
that stream by stopping and restarting a transfer. In this case, all the
TRBs may have already been prepared. Allow the function
__dwc3_gadget_kick_transfer() to go through even though there's no new
TRB.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Tang Bin [Mon, 28 Sep 2020 12:00:51 +0000 (20:00 +0800)]
usb: bdc: remove duplicated error message
in case devm_platform_ioremap_resource() fails, that function already
prints a relevant error message which renders the driver's dev_err()
redundant. Let's remove the unnecessary message and, while at that,
also make sure to pass along the error value returned by
devm_platform_ioremap_resource() instead of always returning -ENOMEM.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
[balbi@kernel.org : improved commit log]
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Wesley Cheng [Tue, 29 Sep 2020 00:20:59 +0000 (17:20 -0700)]
usb: dwc3: Stop active transfers before halting the controller
In the DWC3 databook, for a device initiated disconnect or bus reset, the
driver is required to send dependxfer commands for any pending transfers.
In addition, before the controller can move to the halted state, the SW
needs to acknowledge any pending events. If the controller is not halted
properly, there is a chance the controller will continue accessing stale or
freed TRBs and buffers.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:30 +0000 (17:11 +0800)]
usb: cdns3: gadget: enlarge the TRB ring length
At Android ADB and MTP use case, it uses f_fs which supports scatter list,
it means one request may need several TRBs for it. Besides, TRB consumes
very fast compared to TRB has prepared for above use case, there are at
most 120 pending requests, the date size is 16KB for each request, so four
TRBs (4KB per TRB) per sg entry at worst case. so we need to enlarge the
TRB ring length to avoid "no free TRB error". Since each TRB only consumes
12 bytes (3 * 32 bits), we enlarge the TRB length to 600, it leaves some
buffers for potential "no free TRB error", and only increases a little
memory cost.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:29 +0000 (17:11 +0800)]
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
The scatter buffer list support earlier than DEV_VER_V2 is not
good enough, software can't know well about short transfer for it.
Cc: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:28 +0000 (17:11 +0800)]
usb: cdns3: gadget: need to handle sg case for workaround 2 case
Add sg case for workaround 2, the workaround 2 is described at the
beginning of this file.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:27 +0000 (17:11 +0800)]
usb: cdns3: gadget: handle sg list use case at completion correctly
- Judge each TRB has been handled at cdns3_trb_handled, since
the DMA pointer may be at the middle of the TD, we can't consider
this TD has finished at that time.
- Calculate req->actual according to finished TRBs.
- Handle short transfer for sg list use case correctly. When the
short transfer occurs, we check OUT_SMM at TRB to see if it is
the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:26 +0000 (17:11 +0800)]
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
For sg buffer list use case, we need to add ISP for each TRB, and
add CHAIN bit for each TRB except for the last TRB.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:24 +0000 (17:11 +0800)]
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
It only dumps the first TRB per request, it is not useful if only dump
the first TRB when there are several TRBs per request. We improve it by
dumpping all TRBs per request in this commit.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Thu, 10 Sep 2020 09:11:23 +0000 (17:11 +0800)]
usb: cdns3: gadget: using correct sg operations
It needs to use request->num_mapped_sgs to indicate mapped sg number,
the request->num_sgs is the sg number before the mapping. These two
entries have different values for the platforms which iommu or
swiotlb is used. Besides, it needs to use correct sg APIs for
mapped sg list for TRB assignment.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Mauro Carvalho Chehab [Tue, 8 Sep 2020 07:20:57 +0000 (09:20 +0200)]
dt-bindings: document a new quirk for dwc3
At Hikey 970, setting the SPLIT disable at the General
User Register 3 is required.
Without that, the URBs generated by the usbhid driver
return -EPROTO errors. That causes the code at
hid-core.c to call hid_io_error(), which schedules
a reset_work, causing a call to hid_reset().
In turn, the code there will call:
usb_queue_reset_device(usbhid->intf);
The net result is that the input devices won't work, and
will be reset on every 0.5 seconds:
[ 33.122384] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 33.378220] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 33.698394] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0000
[ 34.882365] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 35.138217] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 35.458617] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0000
[ 36.642392] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 36.898207] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 37.218598] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0000
[ 38.402368] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 38.658174] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
[ 38.978594] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0000
[ 40.162361] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0002
[ 40.418148] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
...
[ 397.698132] usb 1-1.1: reset low-speed USB device number 3 using xhci-hcd
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Yu Chen [Tue, 8 Sep 2020 07:20:56 +0000 (09:20 +0200)]
usb: dwc3: Add splitdisable quirk for Hisilicon Kirin Soc
SPLIT_BOUNDARY_DISABLE should be set for DesignWare USB3 DRD Core
of Hisilicon Kirin Soc when dwc3 core act as host.
[mchehab: dropped a dev_dbg() as only traces are now allowwed on this driver]
Signed-off-by: Yu Chen <chenyu56@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Tang Bin [Sun, 27 Sep 2020 13:53:04 +0000 (21:53 +0800)]
usb: bdc: Fix unused assignment in bdc_probe()
Delete unused initialized value of 'ret', because it will
be assigned by the function clk_prepare_enable().
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Zqiang [Sun, 27 Sep 2020 08:01:16 +0000 (16:01 +0800)]
usb: gadget: uvc: Fix the wrong v4l2_device_unregister call
If an error occurred before calling the 'v4l2_device_register' func,
and then goto error, but no need to call 'v4l2_device_unregister'
func.
Signed-off-by: Zqiang <qiang.zhang@windriver.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:22:14 +0000 (01:22 -0700)]
usb: dwc3: gadget: Rename misleading function names
The functions dwc3_prepare_one_trb_sg and dwc3_prepare_one_trb_linear
are not necessarily preparing "one" TRB, it can prepare multiple TRBs.
Rename these functions as follow:
dwc3_prepare_one_trb_sg -> dwc3_prepare_trbs_sg
dwc3_prepare_one_trb_linear -> dwc3_prepare_trbs_linear
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:22:07 +0000 (01:22 -0700)]
usb: dwc3: gadget: Refactor preparing last TRBs
There are a lot of common codes for preparing SG and linear TRBs.
Refactor them for easier read.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:22:01 +0000 (01:22 -0700)]
usb: dwc3: gadget: Set IOC if not enough for extra TRBs
If we run out of TRBs because we need extra TRBs, make sure to set the
IOC bit for the previously prepared TRB to get completion notification
to free up TRBs to resume later.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:55 +0000 (01:21 -0700)]
usb: dwc3: gadget: Check for number of TRBs prepared
By returning the number of TRBs prepared, we know whether to execute
__dwc3_gadget_kick_transfer(). This allows us to check if we ran out of
TRBs when extra TRBs are needed for OUT transfers. It also allows us to
properly handle usb_gadget_map_request_by_dev() error.
Fixes:
c6267a51639b ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:49 +0000 (01:21 -0700)]
usb: dwc3: gadget: Return the number of prepared TRBs
In preparation for fixing the check for number of remaining TRBs,
revise dwc3_prepare_one_trb_linear() and dwc3_prepare_one_trb_sg() to
return the number of prepared TRBs.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:43 +0000 (01:21 -0700)]
usb: dwc3: ep0: Fix ZLP for OUT ep0 requests
The current ZLP handling for ep0 requests is only for control IN
requests. For OUT direction, DWC3 needs to check and setup for MPS
alignment.
Usually, control OUT requests can indicate its transfer size via the
wLength field of the control message. So usb_request->zero is usually
not needed for OUT direction. To handle ZLP OUT for control endpoint,
make sure the TRB is MPS size.
Cc: stable@vger.kernel.org
Fixes:
c7fcdeb2627c ("usb: dwc3: ep0: simplify EP0 state machine")
Fixes:
d6e5a549cc4d ("usb: dwc3: simplify ZLP handling")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:36 +0000 (01:21 -0700)]
usb: dwc3: gadget: Improve TRB ZLP setup
For OUT requests that requires extra TRBs for ZLP. We don't need to
prepare the 0-length TRB and simply prepare the MPS size TRB. This
reduces 1 TRB needed to prepare for ZLP.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:30 +0000 (01:21 -0700)]
usb: dwc3: gadget: Refactor preparing extra TRB
When the driver prepares the extra TRB, it uses bounce buffer. If we
just add a new parameter to dwc3_prepare_one_trb() to indicate this,
then we can refactor and simplify the driver quite a bit.
dwc3_prepare_one_trb() also checks if a request had been moved to the
started list. This is a prerequisite to subsequence patches improving
the handling of extra TRBs.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:24 +0000 (01:21 -0700)]
usb: dwc3: gadget: Reclaim extra TRBs after request completion
An SG request may be partially completed (due to no available TRBs).
Don't reclaim extra TRBs and clear the needs_extra_trb flag until the
request is fully completed. Otherwise, the driver will reclaim the wrong
TRB.
Cc: stable@vger.kernel.org
Fixes:
1f512119a08c ("usb: dwc3: gadget: add remaining sg entries to ring")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 24 Sep 2020 08:21:18 +0000 (01:21 -0700)]
usb: dwc3: gadget: Check MPS of the request length
When preparing for SG, not all the entries are prepared at once. When
resume, don't use the remaining request length to calculate for MPS
alignment. Use the entire request->length to do that.
Cc: stable@vger.kernel.org
Fixes:
5d187c0454ef ("usb: dwc3: gadget: Don't setup more than requested")
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Chunfeng Yun [Mon, 14 Sep 2020 06:17:30 +0000 (14:17 +0800)]
usb: gadget: bcm63xx_udc: fix up the error of undeclared usb_debug_root
Fix up the build error caused by undeclared usb_debug_root
Cc: stable <stable@vger.kernel.org>
Fixes:
a66ada4f241c ("usb: gadget: bcm63xx_udc: create debugfs directory under usb root")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thierry Reding [Thu, 6 Aug 2020 16:04:17 +0000 (18:04 +0200)]
usb: gadget: tegra-xudc: Do not print errors on probe deferral
Probe deferral is an expected condition and can happen multiple times
during boot. Make sure not to output an error message in that case
because they are not useful.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thierry Reding [Thu, 6 Aug 2020 16:04:16 +0000 (18:04 +0200)]
usb: gadget: tegra-xudc: Properly align parameters
Align parameters on subsequent lines with the parameters on the first
line for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Colin Ian King [Wed, 5 Aug 2020 13:14:58 +0000 (14:14 +0100)]
usb: gadget: fix spelling mistake "Dectected" -> "Detected"
There is a spelling mistake in a literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thierry Reding [Thu, 6 Aug 2020 16:04:15 +0000 (18:04 +0200)]
usb: gadget: tegra-xudc: Use consistent spelling and formatting
Make sure to use consistent spelling and formatting in error messages.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Christophe JAILLET [Sun, 9 Aug 2020 07:29:48 +0000 (09:29 +0200)]
usb: gadget: tegra-xudc: Avoid GFP_ATOMIC where it is not needed
There is no need to use GFP_ATOMIC here. It is a probe function, no
spinlock is taken.
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Tue, 11 Aug 2020 02:00:26 +0000 (10:00 +0800)]
usb: gadget: core: do not try to disconnect gadget if it is not connected
Current UDC core connects gadget during the loading gadget flow
(udc_bind_to_driver->usb_udc_connect_control), but for
platforms which do not connect gadget if the VBUS is not there,
they call usb_gadget_disconnect, but the gadget is not connected
at this time, notify disconnecton for the gadget driver is meaningless
at this situation.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Thinh Nguyen [Thu, 30 Jul 2020 23:29:03 +0000 (16:29 -0700)]
usb: dwc3: gadget: Refactor ep command completion
Refactor END_TRANSFER command completion handling and move it outside of
the switch statement to its own function. This makes it cleaner and
consistent with other event handler functions. No functional change
here.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Krzysztof Kozlowski [Fri, 31 Jul 2020 07:41:22 +0000 (09:41 +0200)]
usb: gadget: s3c: Remove unused 'udc' variable
Remove unused 'udc' variable to fix compile warnings:
drivers/usb/gadget/udc/s3c2410_udc.c: In function 's3c2410_udc_dequeue':
drivers/usb/gadget/udc/s3c2410_udc.c:1268:22: warning: variable 'udc' set but not used [-Wunused-but-set-variable]
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Li Jun [Wed, 22 Jul 2020 09:02:55 +0000 (17:02 +0800)]
usb: dwc3: debugfs: do not queue work if try to change mode on non-drd
Do not try to queue a drd work for change mode if the port is not a drd,
this is to avoid below kernel dump:
[ 60.115529] ------------[ cut here ]------------
[ 60.120166] WARNING: CPU: 1 PID: 627 at kernel/workqueue.c:1473
__queue_work+0x46c/0x520
[ 60.128254] Modules linked in:
[ 60.131313] CPU: 1 PID: 627 Comm: sh Not tainted
5.7.0-rc4-00022-g914a586-dirty #135
[ 60.139054] Hardware name: NXP i.MX8MQ EVK (DT)
[ 60.143585] pstate:
a0000085 (NzCv daIf -PAN -UAO)
[ 60.148376] pc : __queue_work+0x46c/0x520
[ 60.152385] lr : __queue_work+0x314/0x520
[ 60.156393] sp :
ffff8000124ebc40
[ 60.159705] x29:
ffff8000124ebc40 x28:
ffff800011808018
[ 60.165018] x27:
ffff800011819ef8 x26:
ffff800011d39980
[ 60.170331] x25:
ffff800011808018 x24:
0000000000000100
[ 60.175643] x23:
0000000000000013 x22:
0000000000000001
[ 60.180955] x21:
ffff0000b7c08e00 x20:
ffff0000b6c31080
[ 60.186267] x19:
ffff0000bb99bc00 x18:
0000000000000000
[ 60.191579] x17:
0000000000000000 x16:
0000000000000000
[ 60.196891] x15:
0000000000000000 x14:
0000000000000000
[ 60.202202] x13:
0000000000000000 x12:
0000000000000000
[ 60.207515] x11:
0000000000000000 x10:
0000000000000040
[ 60.212827] x9 :
ffff800011d55460 x8 :
ffff800011d55458
[ 60.218138] x7 :
ffff0000b7800028 x6 :
0000000000000000
[ 60.223450] x5 :
ffff0000b7800000 x4 :
0000000000000000
[ 60.228762] x3 :
ffff0000bb997cc0 x2 :
0000000000000001
[ 60.234074] x1 :
0000000000000000 x0 :
ffff0000b6c31088
[ 60.239386] Call trace:
[ 60.241834] __queue_work+0x46c/0x520
[ 60.245496] queue_work_on+0x6c/0x90
[ 60.249075] dwc3_set_mode+0x48/0x58
[ 60.252651] dwc3_mode_write+0xf8/0x150
[ 60.256489] full_proxy_write+0x5c/0xa8
[ 60.260327] __vfs_write+0x18/0x40
[ 60.263729] vfs_write+0xdc/0x1c8
[ 60.267045] ksys_write+0x68/0xf0
[ 60.270360] __arm64_sys_write+0x18/0x20
[ 60.274286] el0_svc_common.constprop.0+0x68/0x160
[ 60.279077] do_el0_svc+0x20/0x80
[ 60.282394] el0_sync_handler+0x10c/0x178
[ 60.286403] el0_sync+0x140/0x180
[ 60.289716] ---[ end trace
70b155582e2b7988 ]---
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Li Jun [Tue, 28 Jul 2020 12:42:41 +0000 (20:42 +0800)]
usb: dwc3: core: add phy cleanup for probe error handling
Add the phy cleanup if dwc3 mode init fail, which is the missing part of
de-init for dwc3 core init.
Fixes:
c499ff71ff2a ("usb: dwc3: core: re-factor init and exit paths")
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Li Jun [Tue, 28 Jul 2020 12:42:40 +0000 (20:42 +0800)]
usb: dwc3: core: don't trigger runtime pm when remove driver
No need to trigger runtime pm in driver removal, otherwise if user
disable auto suspend via sys file, runtime suspend may be entered,
which will call dwc3_core_exit() again and there will be clock disable
not balance warning:
[ 2026.820154] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 2026.825268] usb usb2: USB disconnect, device number 1
[ 2026.831017] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 2026.836806] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 2026.842029] usb usb1: USB disconnect, device number 1
[ 2026.848029] xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered
[ 2026.865889] ------------[ cut here ]------------
[ 2026.870506] usb2_ctrl_root_clk already disabled
[ 2026.875082] WARNING: CPU: 0 PID: 731 at drivers/clk/clk.c:958
clk_core_disable+0xa0/0xa8
[ 2026.883170] Modules linked in: dwc3(-) phy_fsl_imx8mq_usb [last
unloaded: dwc3]
[ 2026.890488] CPU: 0 PID: 731 Comm: rmmod Not tainted
5.8.0-rc7-00280-g9d08cca-dirty #245
[ 2026.898489] Hardware name: NXP i.MX8MQ EVK (DT)
[ 2026.903020] pstate:
20000085 (nzCv daIf -PAN -UAO BTYPE=--)
[ 2026.908594] pc : clk_core_disable+0xa0/0xa8
[ 2026.912777] lr : clk_core_disable+0xa0/0xa8
[ 2026.916958] sp :
ffff8000121b39a0
[ 2026.920271] x29:
ffff8000121b39a0 x28:
ffff0000b11f3700
[ 2026.925583] x27:
0000000000000000 x26:
ffff0000b539c700
[ 2026.930895] x25:
000001d7e44e1232 x24:
ffff0000b76fa800
[ 2026.936208] x23:
ffff0000b76fa6f8 x22:
ffff800008d01040
[ 2026.941520] x21:
ffff0000b539ce00 x20:
ffff0000b7105000
[ 2026.946832] x19:
ffff0000b7105000 x18:
0000000000000010
[ 2026.952144] x17:
0000000000000001 x16:
0000000000000000
[ 2026.957456] x15:
ffff0000b11f3b70 x14:
ffffffffffffffff
[ 2026.962768] x13:
ffff8000921b36f7 x12:
ffff8000121b36ff
[ 2026.968080] x11:
ffff8000119e1000 x10:
ffff800011bf26d0
[ 2026.973392] x9 :
0000000000000000 x8 :
ffff800011bf3000
[ 2026.978704] x7 :
ffff800010695d68 x6 :
0000000000000252
[ 2026.984016] x5 :
ffff0000bb9881f0 x4 :
0000000000000000
[ 2026.989327] x3 :
0000000000000027 x2 :
0000000000000023
[ 2026.994639] x1 :
ac2fa471aa7cab00 x0 :
0000000000000000
[ 2026.999951] Call trace:
[ 2027.002401] clk_core_disable+0xa0/0xa8
[ 2027.006238] clk_core_disable_lock+0x20/0x38
[ 2027.010508] clk_disable+0x1c/0x28
[ 2027.013911] clk_bulk_disable+0x34/0x50
[ 2027.017758] dwc3_core_exit+0xec/0x110 [dwc3]
[ 2027.022122] dwc3_suspend_common+0x84/0x188 [dwc3]
[ 2027.026919] dwc3_runtime_suspend+0x74/0x9c [dwc3]
[ 2027.031712] pm_generic_runtime_suspend+0x28/0x40
[ 2027.036419] genpd_runtime_suspend+0xa0/0x258
[ 2027.040777] __rpm_callback+0x88/0x140
[ 2027.044526] rpm_callback+0x20/0x80
[ 2027.048015] rpm_suspend+0xd0/0x418
[ 2027.051503] __pm_runtime_suspend+0x58/0xa0
[ 2027.055693] dwc3_runtime_idle+0x7c/0x90 [dwc3]
[ 2027.060224] __rpm_callback+0x88/0x140
[ 2027.063973] rpm_idle+0x78/0x150
[ 2027.067201] __pm_runtime_idle+0x58/0xa0
[ 2027.071130] dwc3_remove+0x64/0xc0 [dwc3]
[ 2027.075140] platform_drv_remove+0x28/0x48
[ 2027.079239] device_release_driver_internal+0xf4/0x1c0
[ 2027.084377] driver_detach+0x4c/0xd8
[ 2027.087954] bus_remove_driver+0x54/0xa8
[ 2027.091877] driver_unregister+0x2c/0x58
[ 2027.095799] platform_driver_unregister+0x10/0x18
[ 2027.100509] dwc3_driver_exit+0x14/0x1408 [dwc3]
[ 2027.105129] __arm64_sys_delete_module+0x178/0x218
[ 2027.109922] el0_svc_common.constprop.0+0x68/0x160
[ 2027.114714] do_el0_svc+0x20/0x80
[ 2027.118031] el0_sync_handler+0x88/0x190
[ 2027.121953] el0_sync+0x140/0x180
[ 2027.125267] ---[ end trace
027f4f8189958f1f ]---
[ 2027.129976] ------------[ cut here ]------------
Fixes:
fc8bb91bc83e ("usb: dwc3: implement runtime PM")
Cc: <stable@vger.kernel.org>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Fri, 21 Aug 2020 02:55:49 +0000 (10:55 +0800)]
Revert "usb: udc: allow adding and removing the same gadget device"
We have already allocated gadget structure dynamically at UDC (dwc3)
driver, so commit
fac323471df6 ("usb: udc: allow adding and removing
the same gadget device")could be reverted.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Fri, 21 Aug 2020 02:55:48 +0000 (10:55 +0800)]
usb: dwc3: allocate gadget structure dynamically
The current code uses commit
fac323471df6 ("usb: udc: allow adding
and removing the same gadget device") as the workaround to let
the gadget device is re-used, but it is not allowed from driver
core point. In this commit, we allocate gadget structure dynamically,
and free it at its release function. Since the gadget device's
driver_data has already occupied by usb_composite_dev structure, we have
to use gadget device's platform data to store dwc3 structure.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Fri, 21 Aug 2020 02:55:47 +0000 (10:55 +0800)]
usb: cdns3: gadget: fix possible memory leak
If cdns3_gadget_start is failed, it never frees cdns3_device structure.
Meanwhile, there is no release function for gadget device, it causes
there is no sync with driver core.
To fix this, we add release function for gadget device, and free
cdns3_device structure at there. Meanwhile, With the new UDC core
APIs, we could work with driver core better to handle memory leak
issue.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Alan Stern [Fri, 21 Aug 2020 02:55:46 +0000 (10:55 +0800)]
USB: UDC: net2272: Fix memory leaks
Like net2280 (on which it was based), the net2272 UDC driver has a
problem with leaking memory along some of its failure pathways. It
also has another problem, not previously noted, in that some of the
failure pathways will call usb_del_gadget_udc() without first calling
usb_add_gadget_udc_release(). And it leaks memory by calling kfree()
when it should call put_device().
Until now it has been impossible to handle the memory leaks, because of
lack of support in the UDC core for separately initializing and adding
gadgets, or for separately deleting and freeing gadgets. An earlier
patch in this series adds the necessary support, making it possible to
fix the outstanding problems properly.
This patch adds an "added" flag to the net2272 structure to indicate
whether or not the gadget has been registered (and thus whether or not
to call usb_del_gadget()), and it fixes the deallocation issues by
calling usb_put_gadget() at the appropriate places.
A similar memory leak issue, apparently never before recognized, stems
from the fact that the driver never initializes the drvdata field in
the gadget's embedded struct device! Evidently this wasn't noticed
because the pointer is only ever used as an argument to kfree(), which
doesn't mind getting called with a NULL pointer. In fact, the drvdata
for gadget device will be written by usb_composite_dev structure if
any gadget class is loaded, so it needs to use usb_gadget structure
to get net2280 private data.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Alan Stern [Fri, 21 Aug 2020 02:55:45 +0000 (10:55 +0800)]
USB: UDC: net2280: Fix memory leaks
As Anton and Evgeny have noted, the net2280 UDC driver has a problem
with leaking memory along some of its failure pathways. It also has
another problem, not previously noted, in that some of the failure
pathways will call usb_del_gadget_udc() without first calling
usb_add_gadget_udc_release(). And it leaks memory by calling kfree()
when it should call put_device().
Previous attempts to fix the problems have failed because of lack of
support in the UDC core for separately initializing and adding
gadgets, or for separately deleting and freeing gadgets. The previous
patch in this series adds the necessary support, making it possible to
fix the outstanding problems properly.
This patch adds an "added" flag to the net2280 structure to indicate
whether or not the gadget has been registered (and thus whether or not
to call usb_del_gadget()), and it fixes the deallocation issues by
calling usb_put_gadget() at the appropriate point.
A similar memory leak issue, apparently never before recognized, stems
from the fact that the driver never initializes the drvdata field in
the gadget's embedded struct device! Evidently this wasn't noticed
because the pointer is only ever used as an argument to kfree(), which
doesn't mind getting called with a NULL pointer. In fact, the drvdata
for gadget device will be written by usb_composite_dev structure if
any gadget class is loaded, so it needs to use usb_gadget structure
to get net2280 private data.
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reported-by: Anton Vasilyev <vasilyev@ispras.ru>
Reported-by: Evgeny Novikov <novikov@ispras.ru>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Alan Stern [Fri, 21 Aug 2020 02:55:44 +0000 (10:55 +0800)]
USB: UDC: Expand device model API interface
The routines used by the UDC core to interface with the kernel's
device model, namely usb_add_gadget_udc(),
usb_add_gadget_udc_release(), and usb_del_gadget_udc(), provide access
to only a subset of the device model's full API. They include
functionality equivalent to device_register() and device_unregister()
for gadgets, but they omit device_initialize(), device_add(),
device_del(), get_device(), and put_device().
This patch expands the UDC API by adding usb_initialize_gadget(),
usb_add_gadget(), usb_del_gadget(), usb_get_gadget(), and
usb_put_gadget() to fill in the gap. It rewrites the existing
routines to call the new ones.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Peter Chen [Fri, 21 Aug 2020 03:14:37 +0000 (11:14 +0800)]
usb: cdns3: gadget: fix some endian issues
It is found by sparse.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
projects / platform / kernel / linux-starfive.git / log