Daniel Scally [Tue, 23 Nov 2021 00:00:13 +0000 (01:00 +0100)]
media: i2c: Add controls from fwnode to ov8865
Add V4L2_CID_CAMERA_ORIENTATION and V4L2_CID_CAMERA_SENSOR_ROTATION
controls to the ov8865 driver by attempting to parse them from firmware.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:12 +0000 (01:00 +0100)]
media: i2c: cap exposure at height + vblank in ov8865
Exposure limits depend on the total height; when vblank is altered (and
thus the total height is altered), change the exposure limits to reflect
the new cap.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:11 +0000 (01:00 +0100)]
media: i2c: Update HTS values in ov8865
The HTS values for some of the modes in the ov8865 driver are a bit
unusual, coming in lower than the output_size_x is set to. It seems
like they might be calculated to fit the desired framerate into a
configuration with just two data lanes. To bring this more in line
with expected behaviour, raise the HTS values above the output_size_x.
The corollary of that change is that the hardcoded frame intervals
against the modes no longer make sense, so remove those entirely.
Update the .g/s_frame_interval() callbacks to calculate the frame
interval based on the current mode and the vblank and hblank settings.
The implementation of the .enum_frame_interval() callback is no longer
suitable since the possible frame rate is now a continuous range depending
on the vblank control setting, so remove that callback entirely.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:10 +0000 (01:00 +0100)]
media: i2c: Add hblank control to ov8865
Add a V4L2_CID_HBLANK control to the ov8865 driver. This is read only
with timing control intended to be done via vblanking alone.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:09 +0000 (01:00 +0100)]
media: i2c: Add vblank control to ov8865
Add a V4L2_CID_VBLANK control to the ov8865 driver.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:08 +0000 (01:00 +0100)]
media: i2c: Switch control to V4L2_CID_ANALOGUE_GAIN
The V4L2_CID_GAIN control for this driver configures registers that
the datasheet specifies as analogue gain. Switch the control's ID
to V4L2_CID_ANALOGUE_GAIN.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:07 +0000 (01:00 +0100)]
media: i2c: Add .get_selection() support to ov8865
The ov8865 driver's v4l2_subdev_pad_ops currently does not include
.get_selection() - add support for that callback.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:06 +0000 (01:00 +0100)]
media: i2c: Support 19.2MHz input clock in ov8865
The ov8865 driver as written expects a 24MHz input clock, but the sensor
is sometimes found on x86 platforms with a 19.2MHz input clock supplied.
Add a set of PLL configurations to the driver to support that rate too.
As ACPI doesn't auto-configure the clock rate, check for a clock-frequency
during probe and set that rate if one is found.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:05 +0000 (01:00 +0100)]
media: i2c: Defer probe if not endpoint found
The ov8865 driver is one of those that can be connected to a CIO2
device by the cio2-bridge code. This means that the absence of an
endpoint for this device is not necessarily fatal, as one might be
built by the cio2-bridge when it probes. Return -EPROBE_DEFER if no
endpoint is found rather than a fatal error.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:04 +0000 (01:00 +0100)]
media: i2c: Fix incorrect value in comment
The PLL configuration defined here sets 72MHz (which is correct), not
80MHz. Correct the comment.
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:03 +0000 (01:00 +0100)]
media: i2c: Add ACPI support to ov8865
The ov8865 sensor is sometimes found on x86 platforms enumerated via ACPI.
Add an ACPI match table to the driver so that it's probed on those
platforms.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Hans de Goede [Tue, 23 Nov 2021 00:00:02 +0000 (01:00 +0100)]
media: i2c: ov8865: Fix lockdep error
ov8865_state_init() calls ov8865_state_mipi_configure() which uses
__v4l2_ctrl_s_ctrl[_int64](). This means that sensor->mutex (which
is also sensor->ctrls.handler.lock) must be locked before calling
ov8865_state_init().
Note ov8865_state_mipi_configure() is also used in other places where
the lock is already held so it cannot be changed itself.
This fixes the following lockdep kernel WARN:
[ 13.233421] WARNING: CPU: 0 PID: 8 at drivers/media/v4l2-core/v4l2-ctrls-api.c:833 __v4l2_ctrl_s_ctrl+0x4d/0x60 [videodev]
...
[ 13.234063] Call Trace:
[ 13.234074] ov8865_state_configure+0x98b/0xc00 [ov8865]
[ 13.234095] ov8865_probe+0x4b1/0x54c [ov8865]
[ 13.234117] i2c_device_probe+0x13c/0x2d0
Fixes:
11c0d8fdccc5 ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Tue, 23 Nov 2021 00:00:01 +0000 (01:00 +0100)]
media: i2c: Re-order runtime pm initialisation
The kerneldoc for pm_runtime_set_suspended() says:
"It is not valid to call this function for devices with runtime PM
enabled"
To satisfy that requirement, re-order the calls so that
pm_runtime_enable() is the last one.
Fixes:
11c0d8fdccc5 ("media: i2c: Add support for the OV8865 image sensor")
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Mon, 22 Nov 2021 23:56:13 +0000 (00:56 +0100)]
media: ipu3-cio2: Add link freq for INT33BE entry
Add a link frequency to the cio2-bridge table of supported sensors.
This means that the driver can parse supported link frequencies from
firmware in the usual way and validate that it can accommodate them.
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Mon, 22 Nov 2021 23:56:12 +0000 (00:56 +0100)]
media: i2c: Add support for ov5693 sensor
The OV5693 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2. The
chip is capable of a single lane configuration, but currently only two
lanes are supported.
Most of the sensor's features are supported, with the main exception
being the lens correction algorithm.
The driver provides all mandatory, optional and recommended V4L2 controls
for maximum compatibility with libcamera.
[mchehab: fixed a coding style warning]
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Daniel Scally [Mon, 22 Nov 2021 23:56:11 +0000 (00:56 +0100)]
media: ipu3-cio2: Toggle sensor streaming in pm runtime ops
The .suspend() and .resume() runtime_pm operations for the ipu3-cio2
driver currently do not handle the sensor's stream. Setting .s_stream() on
or off for the sensor subdev means that sensors will pause and resume the
stream at the appropriate time even if their drivers don't implement those
operations.
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Daniel Scally <djrscally@gmail.com>
Tested-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Reviewed-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Thu, 18 Nov 2021 15:40:09 +0000 (16:40 +0100)]
media: i2c: imx274: implement enum_mbus_code
Current driver supports only SRGGB 10 bit RAW bayer format.
Add the enum_mbus_code implementation to report this format supported.
# v4l2-ctl -d /dev/v4l-subdev3 --list-subdev-mbus-codes
ioctl: VIDIOC_SUBDEV_ENUM_MBUS_CODE (pad=0)
0x300f: MEDIA_BUS_FMT_SRGGB10_1X10
#
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Thu, 18 Nov 2021 12:51:51 +0000 (13:51 +0100)]
media: i2c: imx274: fix trivial typo obainted/obtained
Fix typo obainted/obtained.
Fixes:
0985dd306f72 ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Thu, 18 Nov 2021 07:17:15 +0000 (08:17 +0100)]
media: i2c: imx274: fix trivial typo expsoure/exposure
Fix typo expsoure/exposure
Fixes:
0985dd306f72 ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Eugen Hristev [Wed, 17 Nov 2021 15:40:09 +0000 (16:40 +0100)]
media: i2c: imx274: fix s_frame_interval runtime resume not requested
pm_runtime_resume_and_get should be called when the s_frame_interval
is called.
The driver will try to access device registers to configure VMAX, coarse
time and exposure.
Currently if the runtime is not resumed, this fails:
# media-ctl -d /dev/media0 --set-v4l2 '"IMX274 1-001a":0[fmt:SRGGB10_1X10/3840x2
160@1/10]'
IMX274 1-001a: imx274_binning_goodness: ask 3840x2160, size 3840x2160, goodness 0
IMX274 1-001a: imx274_binning_goodness: ask 3840x2160, size 1920x1080, goodness -3000
IMX274 1-001a: imx274_binning_goodness: ask 3840x2160, size 1280x720, goodness -4000
IMX274 1-001a: imx274_binning_goodness: ask 3840x2160, size 1280x540, goodness -4180
IMX274 1-001a: __imx274_change_compose: selected 1x1 binning
IMX274 1-001a: imx274_set_frame_interval: input frame interval = 1 / 10
IMX274 1-001a: imx274_read_mbreg : addr 0x300e, val=0x1 (2 bytes)
IMX274 1-001a: imx274_set_frame_interval : register SVR = 1
IMX274 1-001a: imx274_read_mbreg : addr 0x30f6, val=0x6a8 (2 bytes)
IMX274 1-001a: imx274_set_frame_interval : register HMAX = 1704
IMX274 1-001a: imx274_set_frame_length : input length = 2112
IMX274 1-001a: imx274_write_mbreg : i2c bulk write failed, 30f8 = 884 (3 bytes)
IMX274 1-001a: imx274_set_frame_length error = -121
IMX274 1-001a: imx274_set_frame_interval error = -121
Unable to setup formats: Remote I/O error (121)
The device is not resumed thus the remote I/O error.
Setting the frame interval works at streaming time, because
pm_runtime_resume_and_get is called at s_stream time before sensor setup.
The failure happens when only the s_frame_interval is called separately
independently on streaming time.
Fixes:
ad97bc37426c ("media: i2c: imx274: Add IMX274 power on and off sequence")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Kieran Bingham [Tue, 2 Nov 2021 11:02:43 +0000 (12:02 +0100)]
media: i2c: max9286: Depend on VIDEO_V4L2
The MAX9286 has not explicitly declared a dependency upon VIDEO_V4L2.
While this dependency has likely always been met by configurations
including it, the device does use V4L2 core, and should depend upon it.
Add VIDEO_V4L2 as a dependency to match other drivers and prevent
failures when compile testing.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 19:06:42 +0000 (20:06 +0100)]
media: mxl5005s: drop some dead code
As reported by clang (with W=1), the ctrlVal var is never used.
Yet, there are even some loops to estimate it. As this is dead
code, remove it. If ever needed, someone could revert this
patch.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 12:07:01 +0000 (12:07 +0000)]
media: cobalt: drop an unused variable
The clock_control value is read but never actually used. Based on
a comment at the code, it has to be reset at the function.
So, drop the variable that stores its value.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:56:50 +0000 (11:56 +0000)]
media: mtk-mdp: address a clang warning
The typecasts at the dvb-core generate clang warnings when W=1
is enabled.
Such warning is harmless, but it causes the build to break with
CONFIG_WERROR and W=1 with clang, so do the cast on a way that
it won't produce warnings anymore.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Robert Foss [Mon, 11 Oct 2021 12:13:01 +0000 (14:13 +0200)]
media: camss: Remove unused static function
vfe_reg_clr() is not used in camss-vfe-170.c, and can be removed.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:54:15 +0000 (11:54 +0000)]
media: davinci: vpbe_osd: mark read reg function as __always_unused
Such function is currently unused, but could be needed in the
future. So, keep it, marking it as __always_unused, in order to
avoid a clang W=1 error.
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:48:45 +0000 (11:48 +0000)]
media: imx290: mark read reg function as __always_unused
Such function is currently unused, but could be needed in the
future. So, keep it, marking it as __always_unused, in order to
avoid a clang W=1 error.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:45:26 +0000 (11:45 +0000)]
media: adv7511: drop unused functions
Those are aliases for another function and not used at the
current implementation. So, just drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:42:49 +0000 (11:42 +0000)]
media: adv7604: mark unused functions as such
There are several unused helper macros there, meant to parse some
fields. As those actually help to document the hardware, the
better is to keep them.
However, it generates clang warnings with W=1, causing build to
break with CONFIG_WERROR.
So, add __always_unused to fix such warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:37:36 +0000 (11:37 +0000)]
media: au0828-i2c: drop a duplicated function
This function is not used, so, just drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 12:01:48 +0000 (12:01 +0000)]
media: lmedm04: don't ignore errors when setting a filter
Solves a clang warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:27:22 +0000 (11:27 +0000)]
media: radio-si476x: drop a container_of() abstraction macro
This isn't used anywhere. So, drop it.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 29 Nov 2021 11:38:06 +0000 (12:38 +0100)]
media: si470x: consolidate multiple printk's
When the version warning is given, multiple dev_warn() are
called. Consolidate the ones that could be merged altogether.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:24:38 +0000 (11:24 +0000)]
media: si470x: fix printk warnings with clang
Clang doesn't like "%hu" on macros:
drivers/media/radio/si470x/radio-si470x-i2c.c:414:4: error: format specifies type 'unsigned short' but the argument has type 'int' [-Werror,-Wformat]
drivers/media/radio/si470x/radio-si470x-i2c.c:417:4: error: format specifies type 'unsigned short' but the argument has type 'int' [-Werror,-Wformat]
Besides that, changeset
cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of unnecessary %h[xudi] and %hh[xudi]")
dropped recomendation of using %h.
So, just replace them with "%u".
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 24 Nov 2021 11:21:47 +0000 (11:21 +0000)]
media: solo6x10: mark unused functions as such
There are several unused helper macros there, meant to parse some
fields. As those actually help to document the hardware, the
better is to keep them.
However, it generates clang warnings with W=1, causing build to
break with CONFIG_WERROR.
So, add __always_unused to fix such warnings.
Acked-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 12:30:55 +0000 (12:30 +0000)]
media: si21xx: report eventual errors at set_frontend
If an error occurs while setting the registers at set_frontend,
it is silently ignored. Yet, the variable status is updated.
Change the logic to return an error if it fails to write values
to the registers.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 12:29:13 +0000 (12:29 +0000)]
media: m88ds3103: drop reg11 calculus from m88ds3103b_select_mclk()
This value is never used at the code. So, drop it.
Solves a W=1 clang warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 12:27:48 +0000 (12:27 +0000)]
media: drxk: drop operation_mode from set_dvbt()
This var is set, but never used. So, drop it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 12:26:19 +0000 (12:26 +0000)]
media: drxd: drop offset var from DownloadMicrocode()
The offset is not needed, and it is never used, as the pointer
itself is already incremented.
So, drop it, in order to solve a W=1 clang warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 12:14:23 +0000 (12:14 +0000)]
media: davinci: get rid of an unused function
vpif_get_default_field() seems to be some left-over from a
past code that sets the field order.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Lad Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 09:53:02 +0000 (09:53 +0000)]
media: saa7134-go7007: get rid of to_state() function
This is just an alias for container_of() and it is used only
on a commented code. The commented code actually is an issue that
require fixes, so, move the container_of() call to the commented
code, and drop the unused function.
This way, a fix for the function could be added later without
needing to re-add to_state() function.
This fixes a clang W=1 warning.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 09:49:19 +0000 (09:49 +0000)]
media: adv7842: get rid of two unused functions
Those functions just call a V4L2 core macro, and aren't used
anywhere. Get rid of them, in order to avoid clang warnings with
W=1.
Reviewed-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 09:20:50 +0000 (09:20 +0000)]
media: omap3isp: avoid warnings at IS_OUT_OF_BOUNDS()
Clang with W=1 produces the following warnings:
drivers/media/platform/omap3isp/isph3a_af.c:173:6: error: result of comparison of constant 256 with expression of type '__u8' (aka 'unsigned char') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (IS_OUT_OF_BOUNDS(paxel_cfg->height, OMAP3ISP_AF_PAXEL_HEIGHT_MIN,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/omap3isp/isph3a_af.c:24:33: note: expanded from macro 'IS_OUT_OF_BOUNDS'
(((value) < (min)) || ((value) > (max)))
~~~~~~~ ^ ~~~~~
drivers/media/platform/omap3isp/isph3a_af.c:179:6: error: result of comparison of constant 256 with expression of type '__u8' (aka 'unsigned char') is always false [-Werror,-Wtautological-constant-out-of-range-compare]
if (IS_OUT_OF_BOUNDS(paxel_cfg->width, OMAP3ISP_AF_PAXEL_WIDTH_MIN,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/platform/omap3isp/isph3a_af.c:24:33: note: expanded from macro 'IS_OUT_OF_BOUNDS'
(((value) < (min)) || ((value) > (max)))
~~~~~~~ ^ ~~~~~
2 errors generated.
Use a typecast to avoid such warnings.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 09:08:47 +0000 (09:08 +0000)]
media: omap3isp: mark isp_isr_dbg as __maybe_unused
This function is only used for debugging purposes. When DEBUG
is disabled, it becomes unused, causing a clang warning with W=1.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 09:07:24 +0000 (09:07 +0000)]
media: marvell-ccic: drop to_cam() unused function
This function is an alias for container_of() that it is currently
not used, causing clang warnings. So, drop it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 09:05:51 +0000 (09:05 +0000)]
media: cx25840: drop some unused inline functions
Solve some clang warnings about unused functions by dropping
some time-conversion inline funcs that aren't used anywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 08:59:53 +0000 (08:59 +0000)]
media: dvb-core: dvb_frontend: address some clang warnings
The typecasts at the dvb-core generate clang warnings when W=1
is enabled.
The warns are harmless, but they cause the build to break with
CONFIG_WERROR, so do the cast on a way that it won't produce
warnings anymore.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 08:42:08 +0000 (08:42 +0000)]
media: mc: drop an unused debug function
The gobj_type() function translates the media object type into
a name, being useful for debugging purposes. It is currently
not used. So, drop it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 08:34:26 +0000 (08:34 +0000)]
media: stb6100: mark a currently unused function as such
The stb6100_normalise_regs() function is not used with current
boards, but the driver says that some devices could need it.
Ok, we could simply drop it, but as there's a macro to mark
unused functions, use it.
This should shut up a clang warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 08:32:02 +0000 (08:32 +0000)]
media: cx18: drop an unused macro
The macro p_to_snd_cx18_card() is just a variant for container_of(),
not actually used inside the code. So, drop it.
This address a clang warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 08:29:50 +0000 (08:29 +0000)]
media: ivtv: drop an unused macro
The macro p_to_snd_ivtv_card() is just a variant for container_of(),
not actually used inside the code. So, drop it.
This address a clang warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Mon, 22 Nov 2021 08:24:03 +0000 (08:24 +0000)]
media: cx25821: drop duplicated i2c_slave_did_ack()
This function is defined twice, one at cx25821-i2c and the other
inside cx25821-core. It turns that only the first
is actually used inside the code.
This causes a clang warning.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:42 +0000 (14:38 +0000)]
media: hantro: Support NV12 on the G2 core
The G2 decoder block produces NV12 4x4 tiled format (NV12_4L4).
Enable the G2 post-processor block, in order to produce regular NV12.
The logic in hantro_postproc.c is leveraged to take care of allocating
the extra buffers and configure the post-processor, which is
significantly simpler than the one on the G1.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:41 +0000 (14:38 +0000)]
media: hantro: Staticize a struct in postprocessor code
The struct is not used outside this file, so it can be static.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:40 +0000 (14:38 +0000)]
media: hantro: Support VP9 on the G2 core
VeriSilicon Hantro G2 core supports VP9 codec.
[hverkuil: add kerneldoc line for HANTRO_MODE_VP9_DEC]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:39 +0000 (14:38 +0000)]
media: hantro: Prepare for other G2 codecs
VeriSilicon Hantro G2 core supports other codecs besides hevc.
Factor out some common code in preparation for vp9 support.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:38 +0000 (14:38 +0000)]
media: hantro: Rename registers
Add more consistency in the way registers are named.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Wed, 17 Nov 2021 11:52:56 +0000 (11:52 +0000)]
media: rkvdec: Add the VP9 backend
The Rockchip VDEC supports VP9 profile 0 up to 4096x2304@30fps. Add
a backend for this new format.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Co-developed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:36 +0000 (14:38 +0000)]
media: Add VP9 v4l2 library
Provide code common to vp9 drivers in one central location.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Andrzej Pietrasiewicz [Tue, 16 Nov 2021 14:38:35 +0000 (14:38 +0000)]
media: uapi: Add VP9 stateless decoder controls
Add the VP9 stateless decoder controls plus the documentation that goes
with it.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Co-developed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Adrian Ratiu <adrian.ratiu@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Co-developed-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Daniel Almeida <daniel.almeida@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Tue, 16 Nov 2021 14:38:34 +0000 (14:38 +0000)]
media: hantro: Add quirk for NV12/NV12_4L4 capture format
The G2 core decoder engine produces NV12_4L4 format,
which is a simple NV12 4x4 tiled format. The driver currently
hides this format by always enabling the post-processor engine,
and therefore offering NV12 directly.
This is done without using the logic in hantro_postproc.c
and therefore makes it difficult to add VP9 cleanly.
Since fixing this is not easy, add a small quirk to force
NV12 if HEVC was configured, but otherwise declare NV12_4L4
as the pixel format in imx8mq_vpu_g2_variant.dec_fmts.
This will be used by the VP9 decoder which will be added soon.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Tue, 16 Nov 2021 14:38:33 +0000 (14:38 +0000)]
media: hantro: Simplify postprocessor
Add a 'postprocessed' boolean property to struct hantro_fmt
to signal that a format is produced by the post-processor.
This will allow to introduce the G2 post-processor in a simple way.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Tue, 16 Nov 2021 14:38:32 +0000 (14:38 +0000)]
media: hantro: postproc: Introduce struct hantro_postproc_ops
Turns out the post-processor block on the G2 core is substantially
different from the one on the G1 core. Introduce hantro_postproc_ops
with .enable and .disable methods, which will allow to support
the G2 post-processor cleanly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Ezequiel Garcia [Tue, 16 Nov 2021 14:38:31 +0000 (14:38 +0000)]
media: hantro: postproc: Fix motion vector space size
When the post-processor hardware block is enabled, the driver
allocates an internal queue of buffers for the decoder enginer,
and uses the vb2 queue for the post-processor engine.
For instance, on a G1 core, the decoder engine produces NV12 buffers
and the post-processor engine can produce YUY2 buffers. The decoder
engine expects motion vectors to be appended to the NV12 buffers,
but this is only required for CODECs that need motion vectors,
such as H.264.
Fix the post-processor logic accordingly.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Sudip Mukherjee [Fri, 16 Apr 2021 23:53:36 +0000 (00:53 +0100)]
media: sp887x: drop unneeded assignment
The pointer 'mem' was initialized to 'fw->data' but immediately after
that it was assigned 'fw->data + 10'. Lets remove the extra assignement
and initialize the pointer to the address its going to use.
Link: https://lore.kernel.org/linux-media/20210416235336.1552102-1-sudipm.mukherjee@gmail.com
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Lukas Middendorf [Sun, 18 Apr 2021 00:12:04 +0000 (01:12 +0100)]
media: media si2168: fully initialize si2168 on resume only when necessary
At connection time (or boot) in si2168_probe(), the firmware is not
loaded to the device and the device is not fully activated. It is
not useful or sensible to do this full initialization on resume in
case it has not been previously initialized and is expected to be
in this initialized state.
Calling si2168_init() and therefore reading the firmware file for
the first time during resume leads to problems and should be avoided.
It is however safe to read the firmware file once it has already been
read outside of a suspend/resume situation.
Add a staus flag 'initialized' to store whether si2168_init() has
successfully been called. If initialization fails (e.g. due to missing
firmware file), the flag is not set.
Register a separate si2168_resume callback which only calls
si2168_init() once the 'initialized' flag has been set and it is safe
to load the firmware at resume.
The first call to si2168_init() will now always happen when the device
is actually used for the first time and never during resume.
This avoids the unsafe firmware file reading and should also speed up
resume by skipping unnecessary device initialization.
Link: https://lore.kernel.org/linux-media/20210418001204.7453-3-kernel@tuxforce.de
[mchehab: fix several Coding Style issues]
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Lukas Middendorf [Sun, 18 Apr 2021 16:15:44 +0000 (17:15 +0100)]
media: si2168: drop support for old firmware file name for si2168 B40
The si2168 B40 firmware file name has been changed in or before 2014.
During initialization, the new file name is preferred, but the old file
name is used as a fallback when request_firmware with the new file name
fails. Once reading the old file name has been attempted, only this name
will be used on further firmware loading attempts. During resume,
firmware reading with the new file name can (and likely will) fail even
when it actually exists. So this permanent switch to the fallback
firmware name happens even when not desired.
Any system using a recent kernel version can be expected to have the
firmware under the new name. The major distributions are either using
the dvb firmware collection from LibreELEC, which has the new firmware
file name, or do not package the firmware file but have documentation
pointing towards a manual installation of the firmware file under the
new name. If the firmware is available under the old name, it is
severely outdated. If the switch to the old file name is performed,
further firmware loading will either permanently fail (if it is not
available) or an outdated firmware version will be used.
Drop support for the fallback firmware file name and fail directly if
the firmware is not available under its current name. On following
attempts, the firmware read will then be retried with the correct
current name instead of the old name.
As reasoned above, there should be no negative effects of this change,
while simplifying code (the B40 variant will be handled identical
compared to the other variants of the si2168) and at the same time
fixing possible problems if firmware loading fails on resume.
Link: https://lore.kernel.org/linux-media/20210418161544.58858-1-kernel@tuxforce.de
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Sun, 26 Sep 2021 20:51:28 +0000 (21:51 +0100)]
media: dib0700: Only touch one bit when start/stop an adapter
Only touch the right bit to enable/disable an adapter channel,
without touching the other adapter's one.
Tested on Nova-TD.
Link: https://lore.kernel.org/linux-media/4214942f248baddec9cfd2b4b2424993ac356a51.1632689033.git.mchehab+huawei@kernel.org
Cc: linuxarm@huawei.com, mauro.chehab@huawei.com, Mauro Carvalho Chehab <mchehab+huawei@kernel.org>, Mauro Carvalho Chehab <mchehab@kernel.org>, Michael Kuron <michael.kuron@gmail.com>, linux-kernel@vger.kernel.org, linux-media@vger.kernel.org, pb@linuxtv.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Sun, 26 Sep 2021 20:51:27 +0000 (21:51 +0100)]
media: dib0700: cleanup start/stop streaming logic
Having two different paths to start/stop streaming, depending
weather the USB endpoints are 0x82/0x83 or not makes it more
prune to errors.
Unify the logic.
Link: https://lore.kernel.org/linux-media/065a6fff925a42153671fa5202c81882ca12c59c.1632689033.git.mchehab+huawei@kernel.org
Cc: linuxarm@huawei.com, mauro.chehab@huawei.com, Mauro Carvalho Chehab <mchehab+huawei@kernel.org>, Mauro Carvalho Chehab <mchehab@kernel.org>, Michael Kuron <michael.kuron@gmail.com>, linux-kernel@vger.kernel.org, linux-media@vger.kernel.org, pb@linuxtv.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Michael Kuron [Sun, 26 Sep 2021 20:51:26 +0000 (21:51 +0100)]
media: dib0700: fix undefined behavior in tuner shutdown
This fixes a problem where closing the tuner would leave it in a state
where it would not tune to any channel when reopened. This problem was
discovered as part of https://github.com/hselasky/webcamd/issues/16.
Since adap->id is 0 or 1, this bit-shift overflows, which is undefined
behavior. The driver still worked in practice as the overflow would in
most environments result in 0, which rendered the line a no-op. When
running the driver as part of webcamd however, the overflow could lead
to 0xff due to optimizations by the compiler, which would, in the end,
improperly shut down the tuner.
The bug is a regression introduced in the commit referenced below. The
present patch causes identical behavior to before that commit for
adap->id equal to 0 or 1. The driver does not contain support for
dib0700 devices with more adapters, assuming such even exist.
Tests have been performed with the Xbox One Digital TV Tuner on amd64.
Not all dib0700 devices are expected to be affected by the regression;
this code path is only taken by those with incorrect endpoint numbers.
Link: https://lore.kernel.org/linux-media/1d2fc36d94ced6f67c7cc21dcc469d5e5bdd8201.1632689033.git.mchehab+huawei@kernel.org
Cc: stable@vger.kernel.org
Fixes:
7757ddda6f4f ("[media] DiB0700: add function to change I2C-speed")
Signed-off-by: Michael Kuron <michael.kuron@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Scott K Logan [Sun, 3 Oct 2021 00:18:30 +0000 (01:18 +0100)]
media: s5h1411.c: Fix a typo in the VSB SNR table
This looks like a typo. By manipulating the antenna on a device while
monitoring the reported SNR, I was able to see the unexpected jump.
After applying this patch, the spike was no longer present.
Link: https://lore.kernel.org/linux-media/20211003001805.735092-1-logans@cottsay.net
Signed-off-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Colin Ian King [Thu, 14 Oct 2021 15:12:35 +0000 (16:12 +0100)]
media: drivers: cx24113: remove redundant variable r
Variable r is being assigned values but its value was never used,
being overriden on its first usage. So, drop the initialization.
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/linux-media/20211014151235.62671-1-colin.king@canonical.com
Cc: kernel-janitors@vger.kernel.org, linux-kernel@vger.kernel.org
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Colin Ian King [Thu, 14 Oct 2021 15:32:53 +0000 (16:32 +0100)]
media: dvb-frontends/stv0367: remove redundant variable ADCClk_Hz
GIT_AUTHOR_NAME=Colin King
GIT_AUTHOR_EMAIL=colin.king@canonical.com
Variable ADCClk_Hz is being initialised with a variable that is never read
and then re-assigned immediately afterwards. Clean up the code by removing
it and just returning the return value from the call to stv0367cab_get_mclk
Addresses-Coverity: ("Unused value")
Link: https://lore.kernel.org/linux-media/20211014153253.63527-1-colin.king@canonical.com
Cc: kernel-janitors@vger.kernel.org, linux-kernel@vger.kernel.org
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
zhaoxiao [Wed, 17 Nov 2021 03:06:56 +0000 (03:06 +0000)]
media: dib9000: Use min() instead of doing it manually
Fix following coccicheck warning:
drivers/media/dvb-frontends/dib9000.c:261:10-11: WARNING opportunity for min()
drivers/media/dvb-frontends/dib9000.c:345:10-11: WARNING opportunity for min()
Link: https://lore.kernel.org/linux-media/20211117030656.14984-1-zhaoxiao@uniontech.com
Cc: linux-media@vger.kernel.org, linux-kernel@vger.kernel.org, zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: zhaoxiao <zhaoxiao@uniontech.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Lukas Middendorf [Sun, 18 Apr 2021 00:12:03 +0000 (01:12 +0100)]
media: media dvb_frontend: add suspend and resume callbacks to dvb_frontend_ops
While dvb_tuner_ops already has dedicated suspend and resume callbacks,
dvb_frontend_ops currently does not have them. Add those callbacks and
use them for suspend and resume. If they are not set, the old behavior
of calling sleep or init is used.
This allows dvb_frontend drivers to handle resume differently from init,
and suspend differently from sleep. No change is required for drivers
not needing this functionality.
Link: https://lore.kernel.org/linux-media/20210418001204.7453-2-kernel@tuxforce.de
Cc: Lukas Middendorf <kernel@tuxforce.de>, Antti Palosaari <crope@iki.fi>, Mauro Carvalho Chehab <mchehab@kernel.org>, Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Lukas Middendorf <kernel@tuxforce.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Zheyu Ma [Tue, 11 May 2021 09:00:03 +0000 (10:00 +0100)]
media: b2c2: Add missing check in flexcop_pci_isr:
A out-of-bounds bug can be triggered by an interrupt, the reason for
this bug is the lack of checking of register values.
In flexcop_pci_isr, the driver reads value from a register and uses it as
a dma address. Finally, this address will be passed to the count parameter
of find_next_packet. If this value is larger than the size of dma, the
index of buffer will be out-of-bounds.
Fix this by adding a check after reading the value of the register.
The following KASAN report reveals it:
BUG: KASAN: slab-out-of-bounds in find_next_packet
drivers/media/dvb-core/dvb_demux.c:528 [inline]
BUG: KASAN: slab-out-of-bounds in _dvb_dmx_swfilter
drivers/media/dvb-core/dvb_demux.c:572 [inline]
BUG: KASAN: slab-out-of-bounds in dvb_dmx_swfilter+0x3fa/0x420
drivers/media/dvb-core/dvb_demux.c:603
Read of size 1 at addr
ffff8880608c00a0 by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef #25
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS
rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xec/0x156 lib/dump_stack.c:118
print_address_description+0x78/0x290 mm/kasan/report.c:256
kasan_report_error mm/kasan/report.c:354 [inline]
kasan_report+0x25b/0x380 mm/kasan/report.c:412
__asan_report_load1_noabort+0x19/0x20 mm/kasan/report.c:430
find_next_packet drivers/media/dvb-core/dvb_demux.c:528 [inline]
_dvb_dmx_swfilter drivers/media/dvb-core/dvb_demux.c:572 [inline]
dvb_dmx_swfilter+0x3fa/0x420 drivers/media/dvb-core/dvb_demux.c:603
flexcop_pass_dmx_data+0x2e/0x40 drivers/media/common/b2c2/flexcop.c:167
flexcop_pci_isr+0x3d1/0x5d0 drivers/media/pci/b2c2/flexcop-pci.c:212
__handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149
handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189
handle_irq_event+0xac/0x140 kernel/irq/handle.c:206
handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725
generic_handle_irq_desc include/linux/irqdesc.h:155 [inline]
handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87
do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247
common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
</IRQ>
RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61
Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 62 2f 8c 48 89 e5 e8 fb 31
e8 f8 8b 05 75 4f 8e 03 85 c0 7e 07 0f 00 2d 8a 61 66 00 fb f4 <5d> c3
90 90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RSP: 0018:
ffff88806b71fcc8 EFLAGS:
00000246 ORIG_RAX:
ffffffffffffffde
RAX:
0000000000000000 RBX:
ffffffff8bde44c8 RCX:
ffffffff88a11285
RDX:
0000000000000000 RSI:
0000000000000004 RDI:
ffffffff8c2f6200
RBP:
ffff88806b71fcc8 R08:
fffffbfff185ec40 R09:
fffffbfff185ec40
R10:
0000000000000001 R11:
fffffbfff185ec40 R12:
0000000000000002
R13:
ffffffff8be9d6e0 R14:
0000000000000000 R15:
0000000000000000
arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline]
default_idle+0x6f/0x360 arch/x86/kernel/process.c:557
arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548
default_idle_call+0x3b/0x60 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263
cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369
start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Allocated by task 1:
save_stack+0x43/0xd0 mm/kasan/kasan.c:448
set_track mm/kasan/kasan.c:460 [inline]
kasan_kmalloc+0xad/0xe0 mm/kasan/kasan.c:553
kasan_slab_alloc+0x11/0x20 mm/kasan/kasan.c:490
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2741 [inline]
slab_alloc mm/slub.c:2749 [inline]
kmem_cache_alloc+0xeb/0x280 mm/slub.c:2754
kmem_cache_zalloc include/linux/slab.h:699 [inline]
__kernfs_new_node+0xe2/0x6f0 fs/kernfs/dir.c:633
kernfs_new_node+0x9a/0x120 fs/kernfs/dir.c:693
__kernfs_create_file+0x5f/0x340 fs/kernfs/file.c:992
sysfs_add_file_mode_ns+0x22a/0x4e0 fs/sysfs/file.c:306
create_files fs/sysfs/group.c:63 [inline]
internal_create_group+0x34e/0xc30 fs/sysfs/group.c:147
sysfs_create_group fs/sysfs/group.c:173 [inline]
sysfs_create_groups+0x9c/0x140 fs/sysfs/group.c:200
driver_add_groups+0x3e/0x50 drivers/base/driver.c:129
bus_add_driver+0x3a5/0x790 drivers/base/bus.c:684
driver_register+0x1cd/0x410 drivers/base/driver.c:170
__pci_register_driver+0x197/0x200 drivers/pci/pci-driver.c:1411
cx88_audio_pci_driver_init+0x23/0x25 drivers/media/pci/cx88/cx88-alsa.c:
1017
do_one_initcall+0xe0/0x610 init/main.c:884
do_initcall_level init/main.c:952 [inline]
do_initcalls init/main.c:960 [inline]
do_basic_setup init/main.c:978 [inline]
kernel_init_freeable+0x4d0/0x592 init/main.c:1145
kernel_init+0x18/0x190 init/main.c:1062
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:415
Freed by task 0:
(stack is not available)
The buggy address belongs to the object at
ffff8880608c0000
which belongs to the cache kernfs_node_cache of size 160
The buggy address is located 0 bytes to the right of
160-byte region [
ffff8880608c0000,
ffff8880608c00a0)
The buggy address belongs to the page:
page:
ffffea0001823000 count:1 mapcount:0 mapping:
ffff88806bed1e00
index:0x0 compound_mapcount: 0
flags: 0x100000000008100(slab|head)
raw:
0100000000008100 dead000000000100 dead000000000200 ffff88806bed1e00
raw:
0000000000000000 0000000000240024 00000001ffffffff 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff8880608bff80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff8880608c0000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
ffff8880608c0080: 00 00 00 00 fc fc fc fc fc fc fc fc 00 00 00 00
^
ffff8880608c0100: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff8880608c0180: fc fc fc fc fc fc fc fc 00 00 00 00 00 00 00 00
==================================================================
Link: https://lore.kernel.org/linux-media/1620723603-30912-1-git-send-email-zheyuma97@gmail.com
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Cai Huoqing [Thu, 16 Sep 2021 02:00:18 +0000 (03:00 +0100)]
media: dvb-core: Convert to SPDX identifier
use SPDX-License-Identifier instead of a verbose license text
and remove verbose license text.
Link: https://lore.kernel.org/linux-media/20210916020018.8550-1-caihuoqing@baidu.com
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Wang Hai [Fri, 15 Oct 2021 08:57:41 +0000 (16:57 +0800)]
media: dmxdev: fix UAF when dvb_register_device() fails
I got a use-after-free report:
dvbdev: dvb_register_device: failed to create device dvb1.dvr0 (-12)
...
==================================================================
BUG: KASAN: use-after-free in dvb_dmxdev_release+0xce/0x2f0
...
Call Trace:
dump_stack_lvl+0x6c/0x8b
print_address_description.constprop.0+0x48/0x70
kasan_report.cold+0x82/0xdb
__asan_load4+0x6b/0x90
dvb_dmxdev_release+0xce/0x2f0
...
Allocated by task 7666:
kasan_save_stack+0x23/0x50
__kasan_kmalloc+0x83/0xa0
kmem_cache_alloc_trace+0x22e/0x470
dvb_register_device+0x12f/0x980
dvb_dmxdev_init+0x1f3/0x230
...
Freed by task 7666:
kasan_save_stack+0x23/0x50
kasan_set_track+0x20/0x30
kasan_set_free_info+0x24/0x40
__kasan_slab_free+0xf2/0x130
kfree+0xd1/0x5c0
dvb_register_device.cold+0x1ac/0x1fa
dvb_dmxdev_init+0x1f3/0x230
...
When dvb_register_device() in dvb_dmxdev_init() fails, dvb_dmxdev_init()
does not return a failure, and the memory pointed to by dvbdev or
dvr_dvbdev is invalid at this point. If they are used subsequently, it
will result in UFA or null-ptr-deref.
If dvb_register_device() in dvb_dmxdev_init() fails, fix the bug by making
dvb_dmxdev_init() return an error as well.
Link: https://lore.kernel.org/linux-media/20211015085741.1203283-1-wanghai38@huawei.com
Fixes:
1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Martin Weber [Tue, 9 Nov 2021 11:43:09 +0000 (11:43 +0000)]
media: coda: V4L2_PIX_FMT_GREY for coda960 JPEG Encoder
support greyscale pix fmt input for coda9_jpeg_encoder. The hardware
supports it, so allow V4L2 Mem2Mem JPEG Encoder use it as well. Tested
on an i.MX6QP.
[hverkuil: updated the Subject line as suggested by Philipp]
Signed-off-by: Martin Weber <martin.weber@br-automation.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Niklas Söderlund [Mon, 8 Nov 2021 16:02:17 +0000 (16:02 +0000)]
media: rcar-vin: Free buffers with error if hardware stop fails
The driver already has logic to detect if it fails to stop properly and
report this error to the user. The driver however did not report the
unused buffers or buffers given to the hardware (if any) with an error,
the buffers where instead returned to user-space in the active state.
Build on the existing detection of the error condition and correctly
return the buffers with an error if it triggers.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dorota Czaplejewicz [Thu, 4 Nov 2021 11:41:53 +0000 (11:41 +0000)]
media: imx: Remove unused functions
Neither imx_media_mbus_fmt_to_ipu_image nor imx_media_ipu_image_to_mbus_fmt
were used anywhere.
Signed-off-by: Dorota Czaplejewicz <dorota.czaplejewicz@puri.sm>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:41 +0000 (13:16 +0100)]
media: stk1160: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
9cb2173e6ea8 ("[media] media: Add stk1160 new driver (easycap replacement)")
Cc: stable@vger.kernel.org # 3.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:40 +0000 (13:16 +0100)]
media: s2255: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Use the common control-message timeout define for the five-second
timeouts.
Fixes:
38f993ad8b1f ("V4L/DVB (8125): This driver adds support for the Sensoray 2255 devices.")
Cc: stable@vger.kernel.org # 2.6.27
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:39 +0000 (13:16 +0100)]
media: pvrusb2: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
d855497edbfb ("V4L/DVB (4228a): pvrusb2 to kernel 2.6.18")
Cc: stable@vger.kernel.org # 2.6.18
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:38 +0000 (13:16 +0100)]
media: em28xx: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
a6c2ba283565 ("[PATCH] v4l: 716: support for em28xx board family")
Cc: stable@vger.kernel.org # 2.6.16
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:37 +0000 (13:16 +0100)]
media: cpia2: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
ab33d5071de7 ("V4L/DVB (3376): Add cpia2 camera support")
Cc: stable@vger.kernel.org # 2.6.17
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:36 +0000 (13:16 +0100)]
media: flexcop-usb: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Note that the driver was multiplying some of the timeout values with HZ
twice resulting in 3000-second timeouts with HZ=1000.
Also note that two of the timeout defines are currently unused.
Fixes:
2154be651b90 ("[media] redrat3: new rc-core IR transceiver device driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:35 +0000 (13:16 +0100)]
media: redrat3: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
2154be651b90 ("[media] redrat3: new rc-core IR transceiver device driver")
Cc: stable@vger.kernel.org # 3.0
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Johan Hovold [Mon, 25 Oct 2021 12:16:34 +0000 (13:16 +0100)]
media: mceusb: fix control-message timeouts
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes:
66e89522aff7 ("V4L/DVB: IR: add mceusb IR receiver driver")
Cc: stable@vger.kernel.org # 2.6.36
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dafna Hirschfeld [Fri, 22 Oct 2021 15:04:10 +0000 (16:04 +0100)]
media: mtk-vcodec: remove unused func parameter
The prarameter bs_size to function vpu_enc_encode
is not used. Remove it.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Dafna Hirschfeld [Fri, 22 Oct 2021 15:04:08 +0000 (16:04 +0100)]
media: mtk-vcodec: enc: add vp8 profile ctrl
In order for the encoder to work with gstreamer
it needs to have the V4L2_CID_MPEG_VIDEO_VP8_PROFILE
ctrl. This patch adds that ctrl with only profile 0
supported.
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 17:44:26 +0000 (17:44 +0000)]
media: atomisp: cleanup qbuf logic
The logic there is meant to be used by newer firmwares.
clean it up, in order to make compatible with the chosen
firmware version.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 14:55:04 +0000 (14:55 +0000)]
media: atomisp: add YUVPP at __atomisp_get_pipe() logic
Aligns it which the Intel Aero firmware.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 18:41:06 +0000 (18:41 +0000)]
media: atomisp: frame.c: drop a now-unused function
ia_css_frame_find_crop_resolution() is not used anymore.
So, remove it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 18:58:25 +0000 (18:58 +0000)]
media: atomisp: pipe_binarydesc: drop logic incompatible with firmware
As we're using this firmware for ISP2401:
https://github.com/intel-aero/meta-intel-aero-base/blob/master/recipes-kernel/linux/linux-yocto/shisp_2401a0_v21.bin
Revert some changes that are not compatible with it, making
the code close to the Intel Aero one.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 18:32:09 +0000 (18:32 +0000)]
media: atomisp: binary.c: drop logic incompatible with firmware
As we're using this firmware for ISP2401:
https://github.com/intel-aero/meta-intel-aero-base/blob/master/recipes-kernel/linux/linux-yocto/shisp_2401a0_v21.bin
It makes no sense to try to select a non-existing binary
inside the firmware. So, revert it to reflect the Intel Aero
device driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 17:44:26 +0000 (17:44 +0000)]
media: atomisp: simplify binary.c
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 17:15:09 +0000 (17:15 +0000)]
media: atomisp: get rid of set pipe version custom ctrl
It doesn't make sense to have a control for that. Besides that,
the Intel Aero implementation doesn't have, which means that
even the custom control is not used in practice, at least
outside Android.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 14:13:11 +0000 (14:13 +0000)]
media: atomisp: atomisp_cmd: make it more compatible with firmware
Change some recovery logic at the driver, in order to make it
more compatible with ISP2401 Intel Aero firmware.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Mauro Carvalho Chehab [Wed, 17 Nov 2021 09:12:50 +0000 (09:12 +0000)]
media: atomisp: sh_css_sp: better support the current firmware
As we're using Intel Aero firmware, make the code closer to the
driver for such device.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>