Jean Delvare [Tue, 24 Jan 2017 12:07:04 +0000 (13:07 +0100)]
clk: mediatek: Fix MT2701 dependencies
If I say "no" to "Clock driver for Mediatek MT2701", I don't want to
be asked individually about each sub-driver. No means no.
Additionally, this driver shouldn't be proposed at all on non-mediatek
builds, unless build-testing.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes:
e9862118272a ("clk: mediatek: Add MT2701 clock support")
Reviewed-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: James Liao <jamesjj.liao@mediatek.com>
Cc: Shunli Wang <shunli.wang@mediatek.com>
Cc: Erin Lo <erin.lo@mediatek.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Keerthy [Fri, 2 Dec 2016 09:05:43 +0000 (14:35 +0530)]
clk: ti: divider: Add the table parsing to get the best divider value
Currently the divider selection logic blindly divides the parent_rate
by the clk rate and gives the divider value for the divider clocks
which do not have the CLK_SET_RATE_PARENT flag set. Add the clk divider
table parsing to get the closest divider available in the table
provided via Device tree.
The code is pretty much taken from: drivers/clk/clk-divider.c.
and used here to fix up the best divider selection logic.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reported-by: Richard Woodruff <r-woodruff2@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Rajendra Nayak [Mon, 23 Jan 2017 04:26:21 +0000 (09:56 +0530)]
clk: qcom: gdsc: Fix handling of hw control enable/disable
Once a gdsc is brought in and out of HW control, there is a
power down and up cycle which can take upto 1us. Polling on
the gdsc status immediately after the hw control enable/disable
can mislead software/firmware to belive the gdsc is already either on
or off, while its yet to complete the power cycle.
To avoid this add a 1us delay post a enable/disable of HW control
mode.
Also after the HW control mode is disabled, poll on the status to
check gdsc status reflects its 'on' before force disabling it
in software.
Reported-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Tested-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Fixes:
904bb4f5c7de ("clk: qcom: gdsc: Add support for gdscs with HW control")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Jerome Brunet [Wed, 25 Jan 2017 10:53:06 +0000 (11:53 +0100)]
clk: meson8b: fix clk81 register address
During meson8b clock probe, clk81 register address is fixed twice.
First using the meson8b_clk_gates array, then by directly changing
meson8b_clk81 register.
As a result meson8b_clk81.reg = HHI_MPEG_CLK_CNTL + clk_base + clk_base.
Fixed by just removing the second fixup.
Fixes:
e31a1900c1ff ("meson: clk: Add support for clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Gabriel Fernandez [Fri, 6 Jan 2017 13:59:23 +0000 (14:59 +0100)]
clk: stm32f7: Introduce stm32f7 clocks for STM32F746 boards
This patch enables clocks for STM32F746 boards.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Thu, 26 Jan 2017 23:52:55 +0000 (15:52 -0800)]
Merge branch 'clk-stm32f4' into clk-next
* clk-stm32f4:
clk: stm32f7: Add stm32f7 clock DT bindings for STM32F746 boards
Masahiro Yamada [Wed, 18 Jan 2017 12:31:19 +0000 (21:31 +0900)]
clk: uniphier: continue probing even if some clocks fail to register
Do not let the entire probe function fail even if some clocks fail
to register. Let's continue with succeeded clocks. This will give
the system more chances to boot and allow us to investigate the
cause of the failure.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Thu, 26 Jan 2017 23:52:37 +0000 (15:52 -0800)]
Merge branch 'clk-imx7', 'clk-bcm2835' into clk-next
* clk-imx7:
clk: imx7d: Add the OCOTP clock
* clk-bcm2835:
clk: bcm2835: Add leaf clock measurement support, disabled by default
clk: bcm2835: Register the DSI0/DSI1 pixel clocks.
clk: bcm2835: Don't rate change PLLs on behalf of DSI PLL dividers.
Gabriel Fernandez [Fri, 6 Jan 2017 13:59:22 +0000 (14:59 +0100)]
clk: stm32f7: Add stm32f7 clock DT bindings for STM32F746 boards
This patch introduces the stm32f7 clock DT bindings.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fabio Estevam [Wed, 18 Jan 2017 17:53:56 +0000 (15:53 -0200)]
clk: imx7d: Add the OCOTP clock
Add the OCOTP so that this hardware block can be used.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Eric Anholt [Tue, 17 Jan 2017 20:31:57 +0000 (07:31 +1100)]
clk: bcm2835: Add leaf clock measurement support, disabled by default
This proved incredibly useful during debugging of the DSI driver, to
see if our clocks were running at rate we requested. Let's leave it
here for the next person interacting with clocks on the platform (and
so that hopefully we can just hook it up to debugfs some day).
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Eric Anholt [Tue, 17 Jan 2017 20:31:56 +0000 (07:31 +1100)]
clk: bcm2835: Register the DSI0/DSI1 pixel clocks.
The DSI pixel clocks are muxed from clocks generated in the analog phy
by the DSI driver. In order to set them as parents, we need to do the
same name lookup dance on them as we do for our root oscillator.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Eric Anholt [Tue, 17 Jan 2017 20:31:55 +0000 (07:31 +1100)]
clk: bcm2835: Don't rate change PLLs on behalf of DSI PLL dividers.
Our core PLLs are intended to be configured once and left alone. With
the SET_RATE_PARENT, asking to set the PLLD_DSI1 clock rate would
change PLLD just to get closer to the requested DSI clock, thus
changing PLLD_PER, the UART and ethernet PHY clock rates downstream of
it, and breaking ethernet.
We *do* want PLLH to change so that PLLH_AUX can be exactly the value
we want, though. Thus, we need to have a per-divider policy of
whether to pass rate changes up.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Khiem Nguyen [Tue, 10 Jan 2017 06:50:58 +0000 (06:50 +0000)]
clk: cs2000: add Suspend/Resume feature
CS2000 needs re-setup when redume, otherwise, it can't
handle correct clock rate.
Signed-off-by: Khiem Nguyen <khiem.nguyen.xt@rvc.renesas.com>
[Kuninori: cleanup original patch]
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Thu, 12 Jan 2017 01:03:24 +0000 (02:03 +0100)]
clk: vc5: Add support for IDT VersaClock 5P49V5923 and 5P49V5933
Add driver for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips. These
chips have two clock inputs, XTAL or CLK, which are muxed into single
PLL/VCO input. In case of 5P49V5923, the XTAL in built into the chip
while the 5P49V5923 requires external XTAL.
The PLL feeds two fractional dividers. Each fractional divider feeds
output mux, which allows selecting between clock from the fractional
divider itself or from output mux on output N-1. In case of output
mux 0, the output N-1 is instead connected to the output from the mux
feeding the PLL.
The driver thus far supports only the 5P49V5923 and 5P49V5933, while
it should be easily extensible to the whole 5P49V59xx family of chips
as they are all pretty similar.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Vasut [Thu, 12 Jan 2017 01:03:23 +0000 (02:03 +0100)]
clk: vc5: Add bindings for IDT VersaClock 5P49V5923 and 5P49V5933
Add bindings for IDT VersaClock 5 5P49V5923 and 5P49V5933 chips.
These are I2C clock generators with optional clock source from
either XTal or dedicated clock generator and, depending on the
model, two or more clock outputs.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Fri, 20 Jan 2017 23:51:55 +0000 (15:51 -0800)]
Merge tag 'v4.11-rockchip-clk1' of git://git./linux/kernel/git/mmind/linux-rockchip into clk-next
Pull Rockchip clk updates from Heiko Stuebner:
A new clock-type for the 1-2 muxes per soc that are for whatever reason
controlled through the General Register Files, support for the rk3328
clock-controller (including a new pll-type) and the usual clock ids and
some fixes.
* tag 'v4.11-rockchip-clk1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: clk: add rockchip,grf property for RK3399
clk: rockchip: use clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: use rk3288 isp_in clock ids
clk: rockchip: add clock ids for memory controller parts on rk3066/rk3188
clk: rockchip: add rk3288 isp_in clock ids
clk: rockchip: Remove useless init of "grf" to -EPROBE_DEFER
clk: rockchip: add clock controller for rk3328
dt-bindings: add bindings for rk3328 clock controller
clk: rockchip: add dt-binding header for rk3328
clk: rockchip: add new pll-type for rk3328
clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288
clk: rockchip: add a clock-type for muxes based in the grf
Stephen Boyd [Fri, 20 Jan 2017 23:49:47 +0000 (15:49 -0800)]
Merge tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung into clk-next
Pull Samsung clk updates from Sylwester Nawrocki:
- addition of the CPU clock configuration data for Exynos4412
Prime SoC variant,
- removal of driver for deprecated Exynos4415 SoC,
- switching from the syscore to regular system sleep PM ops
in the audio subsystem clocks controller driver,
- updates of the definitions of some "Network On Chip" related
clocks.
* tag 'clk-v4.11-samsung' of git://linuxtv.org/snawrocki/samsung:
clk: samsung: Remove Exynos4415 driver (SoC not supported anymore)
clk: samsung: exynos-audss: Replace syscore PM with platform device PM
clk: samsung: exynos5433: Set NoC (Network On Chip) clocks as critical
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
Lucas Stach [Fri, 13 Jan 2017 17:39:43 +0000 (18:39 +0100)]
clk: imx6: don't restrict LDB mux changes on QuadPlus
The LDB mux/gate layout has been fixed on QuadPlus, so there is no need
to restrict the LDB mux changes on this hardware, as the erratum
preventing this from working properly is gone.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Fri, 20 Jan 2017 23:17:50 +0000 (15:17 -0800)]
Merge tag 'clk-renesas-for-v4.11-tag1' of git://git./linux/kernel/git/geert/renesas-drivers into clk-next
Pull renesas clk updates from Geert Uytterhoeven:
- Add CAN and MSIOF related clocks for R-Car M3-W.
* tag 'clk-renesas-for-v4.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers:
clk: renesas: r8a7796: Add MSIOF controller clocks
clk: renesas: r8a7796: Add CAN FD peripheral clock
clk: renesas: r8a7796: Add CANFD clock
clk: renesas: r8a7796: Add CAN peripheral clock
Krzysztof Kozlowski [Sat, 14 Jan 2017 12:36:40 +0000 (14:36 +0200)]
clk: samsung: Remove Exynos4415 driver (SoC not supported anymore)
Support for Exynos4415 is going away because there are no internal nor
external users.
Since commit
46dcf0ff0de3 ("ARM: dts: exynos: Remove exynos4415.dtsi"),
the platform cannot be instantiated so remove also the drivers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Xing Zheng [Tue, 10 Jan 2017 06:15:30 +0000 (14:15 +0800)]
dt-bindings: clk: add rockchip,grf property for RK3399
Add support for rockchip,grf property which is used for GRF muxes
on RK3399.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Fri, 13 Jan 2017 16:32:55 +0000 (17:32 +0100)]
clk: rockchip: use clock ids for memory controller parts on rk3066/rk3188
Add the newly added clock ids to the clock entries of the rk3066/rk3188
clock driver. We won't be needing them in the kernel for a bit yet
but as they're used in the new u-boot ddr setup code/dts we should make
sure the clock ids stay identical and do not differ.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jacob Chen [Tue, 10 Jan 2017 11:59:18 +0000 (19:59 +0800)]
clk: rockchip: use rk3288 isp_in clock ids
Reference the newly added isp clock-ids in the clock-tree.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Fri, 13 Jan 2017 16:13:33 +0000 (17:13 +0100)]
Merge branch 'v4.11-shared/clkids' into v4.11-clk/next
Heiko Stuebner [Fri, 13 Jan 2017 16:10:02 +0000 (17:10 +0100)]
clk: rockchip: add clock ids for memory controller parts on rk3066/rk3188
Add clock ids for the upctl and publ controllers used for ddr control.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Jacob Chen [Tue, 10 Jan 2017 11:59:17 +0000 (19:59 +0800)]
clk: rockchip: add rk3288 isp_in clock ids
Add clock-ids for the isp block of the rk3288.
Signed-off-by: Jacob Chen <jacob-chen@iotwrt.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Arnd Bergmann [Wed, 11 Jan 2017 13:40:52 +0000 (14:40 +0100)]
clk: stm32f4: avoid uninitialized variable access
The failure path in the newly added function tries to free an
uninitialized pointer:
drivers/clk/clk-stm32f4.c: In function 'stm32f4_rcc_init':
drivers/clk/clk-stm32f4.c:1106:4: error: 'gate' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I'm adding an initialization to NULL here to make the kfree()
succeed, and I'm also rearranging the cleanup so that the
same kfree() is used for any error path, making the function
slightly more robust against newly introduced bugs in the
error handling.
Fixes:
daf2d117cbca ("clk: stm32f4: Add lcd-tft clock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Tue, 10 Jan 2017 00:45:06 +0000 (16:45 -0800)]
Merge branch 'clk-fixes' into clk-next
* clk-fixes:
clk/samsung: exynos542x: mark some clocks as critical
Akinobu Mita [Sat, 31 Dec 2016 18:04:36 +0000 (03:04 +0900)]
clk: cdce925: add support for CDCE913, CDCE937, and CDCE949
The CDCE925 is a member of the CDCE(L)9xx programmable clock generator
family. There are also CDCE913, CDCE937, CDCE949 which have different
number of PLLs and outputs.
The clk-cdce925 driver supports only CDCE925 in the family. This adds
support for the CDCE913, CDCE937, CDCE949, too.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Mike Looijmans <mike.looijmans@topic.nl>
Cc: Michael Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Zoran Markovic [Fri, 23 Dec 2016 04:54:44 +0000 (20:54 -0800)]
clk: mdm9615: Add EBI2 clock
Add definition of EBI2 clock used by MDM9615 NAND controller.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: linux-clk@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Zoran Markovic <zmarkovic@sierrawireless.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[sboyd@codeaurora.org: ebi2_clk halt bit is 24 not 23]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Masahiro Yamada [Mon, 26 Dec 2016 02:34:33 +0000 (11:34 +0900)]
clk: uniphier: remove unneeded #include <linux/delay.h>
This include was needed to suppress build error when this driver
was initially merged because <linux/regmap.h> did not include
<linux/delay.h> at that time. (developers' headache across
sub-systems)
The root cause has been fixed by commit
adf08d481b52 ("regmap:
include <linux/delay.h> from include/linux/regmap.h"), so this
line can be dropped now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Thomas Petazzoni [Thu, 22 Dec 2016 12:08:14 +0000 (13:08 +0100)]
clk: mvebu: adjust AP806 CPU clock frequencies to production chip
This commit adjusts the list of possible "Sample At Reset" values that
define the CPU clock frequency of the AP806 (part of Marvell Armada
7K/8K) to the values that have been validated with the production
chip. Earlier values were preliminary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Stephen Boyd [Tue, 10 Jan 2017 00:26:30 +0000 (16:26 -0800)]
Merge branch 'clk-hi3660' into clk-next
* clk-hi3660:
clk: hisilicon: Add clock driver for hi3660 SoC
dt-bindings: Document the hi3660 clock bindings
Zhangfei Gao [Thu, 29 Dec 2016 02:33:25 +0000 (10:33 +0800)]
clk: hisilicon: Add clock driver for hi3660 SoC
Add clock drivers for hi3660 SoC, this driver controls the SoC
registers to supply different clocks to different IPs in the SoC.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
[sboyd@codeaurora.org: Simplify probe with function pointer]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Zhangfei Gao [Thu, 29 Dec 2016 02:33:24 +0000 (10:33 +0800)]
dt-bindings: Document the hi3660 clock bindings
Add DT bindings documentation for hi3660 SoC clock.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Marek Szyprowski [Thu, 22 Dec 2016 09:44:30 +0000 (10:44 +0100)]
clk/samsung: exynos542x: mark some clocks as critical
Some parent clocks of the Exynos542x clock blocks, which have separate
power domains (like DISP, MFC, MSC, GSC, FSYS and G2D) must be always
enabled to access any register related to power management unit or devices
connected to it. For the time being, until a proper solution based on
runtime PM is applied, mark those clocks as critical (instead of ignore
unused or even no flags) to prevent disabling them.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com> [Exynos5800 Peach Pi Chromebook]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Geert Uytterhoeven [Wed, 4 Jan 2017 10:12:33 +0000 (11:12 +0100)]
clk: clk-conf: Do not print error messages if EPROBE_DEFER
EPROBE_DEFER is not an error, hence printing an error message like
clk: couldn't get clock 0 for /soc/display@
feb00000
may confuse the user.
Suppress error messages in case of probe deferral to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Sudeep Holla [Fri, 6 Jan 2017 12:34:30 +0000 (12:34 +0000)]
clk: scpi: don't add cpufreq device if the scpi dvfs node is disabled
Currently we add the virtual cpufreq device unconditionally even when
the SCPI DVFS clock provider node is disabled. This will cause cpufreq
driver to throw errors when it gets initailised on boot/modprobe and
also when the CPUs are hot-plugged back in.
This patch fixes the issue by adding the virtual cpufreq device only if
the SCPI DVFS clock provider is available and registered.
Fixes:
9490f01e2471 ("clk: scpi: add support for cpufreq virtual device")
Reported-by: Michał Zegan <webczat_200@poczta.onet.pl>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Michał Zegan <webczat_200@poczta.onet.pl>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Avaneesh Kumar Dwivedi [Thu, 15 Dec 2016 12:21:30 +0000 (17:51 +0530)]
clk: qcom: Add GCC_MSS_RESET support
Add support to use reset control framework for resetting MSS
with hexagon v56 1.5.0.
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Jun Nie [Fri, 16 Dec 2016 07:26:47 +0000 (15:26 +0800)]
clk: zte: add audio clocks for zx296718
The audio related clock support is missing from the existing zx296718
clock driver. Let's add it, so that the upstream ZX SPDIF driver can
work for HDMI audio support.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[sboyd@codeaurora.org: Staticize some more structures]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Shawn Guo [Fri, 16 Dec 2016 07:26:46 +0000 (15:26 +0800)]
dt-bindings: zx296718-clk: add compatible for audio clock controller
It adds the compatible string for zx296718 audio clock controller.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Shawn Guo [Fri, 16 Dec 2016 07:26:45 +0000 (15:26 +0800)]
clk: zx296718: do not panic on failure
Instead of using panic, we should give an error message and return error
code when of_clk_add_hw_provider() call fails.
Since we have error prompt for failures, the "init over" pr_info output
isn't really necessary but becomes a debug noise. So let's clean it up
along the way.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Nicholas Mc Guire [Mon, 12 Dec 2016 07:40:09 +0000 (08:40 +0100)]
clk: wm831x: fix usleep_range with bad range
The delay here is not in atomic context and does not seem critical with
respect to precision, but usleep_range(min,max) with min==max results in
giving the timer subsystem no room to optimize uncritical delays. Fix
this by setting the range to 2000,3000 us.
Fixes: commit
f05259a6ffa4 ("clk: wm831x: Add initial WM831x clock driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Nikita Yushchenko [Mon, 19 Dec 2016 08:12:09 +0000 (11:12 +0300)]
clk: imx: pllv3: support fractional multiplier on vf610 PLL1/PLL2
On vf610, PLL1 and PLL2 have registers to configure fractional part of
frequency multiplier.
This patch adds support for these registers.
This fixes "fast system clock" issue on boards where bootloader sets
fractional multiplier for PLL1.
Suggested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
CC: Chris Healy <cphealy@gmail.com>
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Jose Abreu [Mon, 12 Dec 2016 11:08:55 +0000 (11:08 +0000)]
clk/axs10x: Clear init field in driver probe
Init field must be cleared in driver probe as this structure is not
dinamically allocated. If not, wrong flags can be passed to core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Carlos Palminha <palminha@synopsys.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Fixes:
923587aafc2c ("clk/axs10x: Add I2S PLL clock driver")
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/
040cc9afdfa0e95ce7a01c406ff427ef7dc0c0fd.
1481540717.git.joabreu@synopsys.com
Stephen Boyd [Tue, 10 Jan 2017 00:06:11 +0000 (16:06 -0800)]
Merge branches 'clk-qcom-rpm8974', 'clk-stm32f4', 'clk-ipq4019' and 'clk-fixes' into clk-next
* clk-qcom-rpm8974:
clk: qcom: smd-rpmcc: Add msm8974 clocks
* clk-stm32f4:
clk: stm32f4: SDIO & 48Mhz clock management for STM32F469 board
clk: stm32f4: Add SAI clocks
clk: stm32f4: Add I2S clock
clk: stm32f4: Add lcd-tft clock
clk: stm32f4: Add post divisor for I2S & SAI PLLs
clk: stm32f4: Add PLL_I2S & PLL_SAI for STM32F429/469 boards
clk: stm32f4: Update DT bindings documentation
* clk-ipq4019:
clk: qcom: ipq4019: Add the cpu clock frequency change notifier
clk: qcom: ipq4019: Add all the frequencies for apss cpu
clk: qcom: ipq4019: correct sdcc frequency and parent name
clk: qcom: ipq4019: Add the nodes for pcnoc
clk: qcom: ipq4019: Add the apss cpu pll divider clock node
clk: qcom: ipq4019: remove fixed clocks and add pll clocks
* clk-fixes:
clk: stm32f4: Use CLK_OF_DECLARE_DRIVER initialization method
clk: renesas: mstp: Support 8-bit registers for r7s72100
Douglas Anderson [Fri, 6 Jan 2017 16:31:01 +0000 (08:31 -0800)]
clk: rockchip: Remove useless init of "grf" to -EPROBE_DEFER
When we used to defer setting the "grf" member to
rockchip_clk_get_grf() it was important to init the "grf" member to an
error value in rockchip_clk_init(). With recent changes, we now set
"grf" right in rockchip_clk_init() (two lines below the place where we
initted it). That makes the old init useless. Get rid of it.
Fixes:
6f339dc2719e ("clk: rockchip: lookup General Register Files in rockchip_clk_init")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Thu, 29 Dec 2016 02:45:11 +0000 (10:45 +0800)]
clk: rockchip: add clock controller for rk3328
Add the clock tree definition for the new rk3328 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Thu, 29 Dec 2016 02:45:09 +0000 (10:45 +0800)]
dt-bindings: add bindings for rk3328 clock controller
Add devicetree bindings for Rockchip cru which found on
Rockchip SoCs.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Thu, 5 Jan 2017 12:06:50 +0000 (13:06 +0100)]
Merge branch 'v4.11-shared/clkids' into v4.11-clk/next
Elaine Zhang [Thu, 29 Dec 2016 02:45:08 +0000 (10:45 +0800)]
clk: rockchip: add dt-binding header for rk3328
Add the dt-bindings header for the rk3328, that gets shared between
the clock controller and the clock references in the dts.
Add softreset ID for rk3328.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Elaine Zhang [Thu, 29 Dec 2016 02:45:10 +0000 (10:45 +0800)]
clk: rockchip: add new pll-type for rk3328
The rk3328's pll and clock are similar with rk3036's,
it different with pll_mode_mask, the rk3328 soc
pll mode only one bit(rk3036 soc have two bits)
so these should be independent and separate from
the series of rk3328s.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Mon, 26 Dec 2016 23:58:23 +0000 (00:58 +0100)]
clk: rockchip: describe aclk_vcodec using the new muxgrf type on rk3288
With the newly introduced clk type for muxes in the grf we now can
describe some missing clocks, like the aclk_vcodec that selects between
aclk_vdpu and aclk_vepu based on a bit set in the general register files.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Heiko Stuebner [Mon, 26 Dec 2016 23:00:38 +0000 (00:00 +0100)]
clk: rockchip: add a clock-type for muxes based in the grf
Rockchip socs often have some tiny number of muxes not controlled from
the core clock controller but through bits set in the general register
files. Add a clock-type that can control these as well, so that we
don't need to work around them being absent.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Linus Torvalds [Sun, 1 Jan 2017 22:31:53 +0000 (14:31 -0800)]
Linux 4.10-rc2
Linus Torvalds [Sun, 1 Jan 2017 20:27:05 +0000 (12:27 -0800)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull DAX updates from Dan Williams:
"The completion of Jan's DAX work for 4.10.
As I mentioned in the libnvdimm-for-4.10 pull request, these are some
final fixes for the DAX dirty-cacheline-tracking invalidation work
that was merged through the -mm, ext4, and xfs trees in -rc1. These
patches were prepared prior to the merge window, but we waited for
4.10-rc1 to have a stable merge base after all the prerequisites were
merged.
Quoting Jan on the overall changes in these patches:
"So I'd like all these 6 patches to go for rc2. The first three
patches fix invalidation of exceptional DAX entries (a bug which
is there for a long time) - without these patches data loss can
occur on power failure even though user called fsync(2). The other
three patches change locking of DAX faults so that ->iomap_begin()
is called in a more relaxed locking context and we are safe to
start a transaction there for ext4"
These have received a build success notification from the kbuild
robot, and pass the latest libnvdimm unit tests. There have not been
any -next releases since -rc1, so they have not appeared there"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
ext4: Simplify DAX fault path
dax: Call ->iomap_begin without entry lock during dax fault
dax: Finish fault completely when loading holes
dax: Avoid page invalidation races and unnecessary radix tree traversals
mm: Invalidate DAX radix tree entries only if appropriate
ext2: Return BH_New buffers for zeroed blocks
Linus Torvalds [Fri, 30 Dec 2016 17:32:26 +0000 (09:32 -0800)]
Merge tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"Two small fixes:
- A merge error on my part broke the DocBook build. I've
requisitioned one of tglx's frozen sharks for appropriate
disciplinary action and resolved to be more careful about testing
the DocBook stuff as long as it's still around.
- Fix an error in unaligned-memory-access.txt"
* tag 'docs-4.10-rc1-fix' of git://git.lwn.net/linux:
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
docs: Fix build failure
Linus Torvalds [Fri, 30 Dec 2016 17:29:50 +0000 (09:29 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a boot failure on some platforms when crypto self test is
enabled along with the new acomp interface"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: testmgr - Use heap buffer for acomp test input
Olof Johansson [Thu, 29 Dec 2016 22:16:07 +0000 (14:16 -0800)]
mm/filemap: fix parameters to test_bit()
mm/filemap.c: In function 'clear_bit_unlock_is_negative_byte':
mm/filemap.c:933:9: error: too few arguments to function 'test_bit'
return test_bit(PG_waiters);
^~~~~~~~
Fixes:
b91e1302ad9b ('mm: optimize PageWaiters bit use for unlock_page()')
Signed-off-by: Olof Johansson <olof@lixom.net>
Brown-paper-bag-by: Linus Torvalds <dummy@duh.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Tue, 27 Dec 2016 19:40:38 +0000 (11:40 -0800)]
mm: optimize PageWaiters bit use for unlock_page()
In commit
62906027091f ("mm: add PageWaiters indicating tasks are
waiting for a page bit") Nick Piggin made our page locking no longer
unconditionally touch the hashed page waitqueue, which not only helps
performance in general, but is particularly helpful on NUMA machines
where the hashed wait queues can bounce around a lot.
However, the "clear lock bit atomically and then test the waiters bit"
sequence turns out to be much more expensive than it needs to be,
because you get a nasty stall when trying to access the same word that
just got updated atomically.
On architectures where locking is done with LL/SC, this would be trivial
to fix with a new primitive that clears one bit and tests another
atomically, but that ends up not working on x86, where the only atomic
operations that return the result end up being cmpxchg and xadd. The
atomic bit operations return the old value of the same bit we changed,
not the value of an unrelated bit.
On x86, we could put the lock bit in the high bit of the byte, and use
"xadd" with that bit (where the overflow ends up not touching other
bits), and look at the other bits of the result. However, an even
simpler model is to just use a regular atomic "and" to clear the lock
bit, and then the sign bit in eflags will indicate the resulting state
of the unrelated bit #7.
So by moving the PageWaiters bit up to bit #7, we can atomically clear
the lock bit and test the waiters bit on x86 too. And architectures
with LL/SC (which is all the usual RISC suspects), the particular bit
doesn't matter, so they are fine with this approach too.
This avoids the extra access to the same atomic word, and thus avoids
the costly stall at page unlock time.
The only downside is that the interface ends up being a bit odd and
specialized: clear a bit in a byte, and test the sign bit. Nick doesn't
love the resulting name of the new primitive, but I'd rather make the
name be descriptive and very clear about the limitation imposed by
trying to work across all relevant architectures than make it be some
generic thing that doesn't make the odd semantics explicit.
So this introduces the new architecture primitive
clear_bit_unlock_is_negative_byte();
and adds the trivial implementation for x86. We have a generic
non-optimized fallback (that just does a "clear_bit()"+"test_bit(7)"
combination) which can be overridden by any architecture that can do
better. According to Nick, Power has the same hickup x86 has, for
example, but some other architectures may not even care.
All these optimizations mean that my page locking stress-test (which is
just executing a lot of small short-lived shell scripts: "make test" in
the git source tree) no longer makes our page locking look horribly bad.
Before all these optimizations, just the unlock_page() costs were just
over 3% of all CPU overhead on "make test". After this, it's down to
0.66%, so just a quarter of the cost it used to be.
(The difference on NUMA is bigger, but there this micro-optimization is
likely less noticeable, since the big issue on NUMA was not the accesses
to 'struct page', but the waitqueue accesses that were already removed
by Nick's earlier commit).
Acked-by: Nick Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marek Szyprowski [Fri, 25 Nov 2016 09:39:54 +0000 (10:39 +0100)]
clk: samsung: exynos-audss: Replace syscore PM with platform device PM
Exynos AUDSS clock driver has been already converted to platform driver,
so remove the dependency on the syscore ops - the last remaining
non-platform driver feature. Platform device's system sleep PM provides
all needed infrastructure for replacing syscore-based PM, so do it now.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Chanwoo Choi [Thu, 8 Dec 2016 04:58:07 +0000 (13:58 +0900)]
clk: samsung: exynos5433: Set NoC (Network On Chip) clocks as critical
The ACLK_BUS0/1/2 are used for NoC (Network on Chip). If NoC's clocks are
disabled, the system halt happens. Following clocks must be always enabled:
- CLK_ACLK_BUS0_400 : NoC's bus clock for PERIC/PERIS/FSYS/MSCL,
- CLK_ACLK_BUS1_400 : NoC's bus clock for MFC/HEVC/G3D,
- CLK_ACLK_BUS2_400 : NoC's bus clock for GSCL/DISP/G2D/CAM0/CAM1/ISP.
This patch also adds the CLK_SET_RATE_PARENT flag to the CLK_SCLK_JPEG_MSCL
because this clock should be used for bus frequency scaling. This clock need
to be changed on the fly with CLK_SET_RATE_PARENT flag.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Bartlomiej Zolnierkiewicz [Thu, 29 Dec 2016 13:36:50 +0000 (14:36 +0100)]
clk: samsung: Add CPU clk configuration data for Exynos4412 Prime
Add cpu clock configuration data for Exynos4412 Prime SoC
(it supports additional PLL rates & CPU frequencies).
Based on Hardkernel's kernel for ODROID-X2/U2/U3 boards.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Linus Torvalds [Wed, 28 Dec 2016 01:51:36 +0000 (17:51 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a hash corruption bug in the marvell driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: marvell - Copy IVDIG before launching partial DMA ahash requests
Linus Torvalds [Wed, 28 Dec 2016 00:04:37 +0000 (16:04 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking fixes from David Miller:
1) Various ipvlan fixes from Eric Dumazet and Mahesh Bandewar.
The most important is to not assume the packet is RX just because
the destination address matches that of the device. Such an
assumption causes problems when an interface is put into loopback
mode.
2) If we retry when creating a new tc entry (because we dropped the
RTNL mutex in order to load a module, for example) we end up with
-EAGAIN and then loop trying to replay the request. But we didn't
reset some state when looping back to the top like this, and if
another thread meanwhile inserted the same tc entry we were trying
to, we re-link it creating an enless loop in the tc chain. Fix from
Daniel Borkmann.
3) There are two different WRITE bits in the MDIO address register for
the stmmac chip, depending upon the chip variant. Due to a bug we
could set them both, fix from Hock Leong Kweh.
4) Fix mlx4 bug in XDP_TX handling, from Tariq Toukan.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
r8169: add support for RTL8168 series add-on card.
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
openvswitch: upcall: Fix vlan handling.
ipv4: Namespaceify tcp_tw_reuse knob
net: korina: Fix NAPI versus resources freeing
net, sched: fix soft lockup in tc_classify
net/mlx4_en: Fix user prio field in XDP forward
tipc: don't send FIN message from connectionless socket
ipvlan: fix multicast processing
ipvlan: fix various issues in ipvlan_process_multicast()
Abhishek Sahu [Thu, 22 Dec 2016 14:40:54 +0000 (20:10 +0530)]
clk: qcom: ipq4019: Add the cpu clock frequency change notifier
The current driver code gives the crash or gets hang while switching
the CPU frequency some time. The APSS CPU Clock divider is not glitch
free so it the APPS clock need to be switched for stable clock during
the change.
This patch adds the frequency change notifier for APSS CPU clock. It
changes the parent of this clock to stable PLL FEPLL500 for
PRE_RATE_CHANGE event. This event will be generated before actual
clock set operations. The clock set operation will again change its
corresponding parent by getting the same from frequency table.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
[sboyd@codeaurora.org: Indent less in probe]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cihangir Akturk [Sat, 17 Dec 2016 17:42:17 +0000 (19:42 +0200)]
Documentation/unaligned-memory-access.txt: fix incorrect comparison operator
In the actual implementation ether_addr_equal function tests for equality to 0
when returning. It seems in commit 0d74c4 it is somehow overlooked to change
this operator to reflect the actual function.
Signed-off-by: Cihangir Akturk <cakturk@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
John Brooks [Fri, 23 Dec 2016 00:53:10 +0000 (00:53 +0000)]
docs: Fix build failure
The 80211.tmpl DocBook file was removed in commit
819bf593767c ("docs-rst:
sphinxify 802.11 documentation"), but the 80211.xml target was re-added to
the Makefile by commit
7ddedebb03b7 ("ALSA: doc: ReSTize
writing-an-alsa-driver document"), leading to a failure when building the
documentation:
*** No rule to make target 'Documentation/DocBook/80211.xml', needed by
'Documentation/DocBook/80211.aux.xml'.
cc: stable@vger.kernel.org
Signed-off-by: John Brooks <john@fastquake.com>
Mea-culpa-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Jonathan Corbet [Tue, 27 Dec 2016 19:53:44 +0000 (12:53 -0700)]
Merge tag 'v4.10-rc1' into docs-next
Linux 4.10-rc1
Kweh, Hock Leong [Tue, 27 Dec 2016 20:07:41 +0000 (04:07 +0800)]
net: stmmac: fix incorrect bit set in gmac4 mdio addr register
Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chun-Hao Lin [Tue, 27 Dec 2016 08:29:43 +0000 (16:29 +0800)]
r8169: add support for RTL8168 series add-on card.
This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jason Wang [Tue, 27 Dec 2016 02:49:54 +0000 (10:49 +0800)]
net: xdp: remove unused bfp_warn_invalid_xdp_buffer()
After commit
73b62bd085f4737679ea9afc7867fa5f99ba7d1b ("virtio-net:
remove the warning before XDP linearizing"), there's no users for
bpf_warn_invalid_xdp_buffer(), so remove it. This is a revert for
commit
f23bc46c30ca5ef58b8549434899fcbac41b2cfc.
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
pravin shelar [Mon, 26 Dec 2016 16:31:27 +0000 (08:31 -0800)]
openvswitch: upcall: Fix vlan handling.
Networking stack accelerate vlan tag handling by
keeping topmost vlan header in skb. This works as
long as packet remains in OVS datapath. But during
OVS upcall vlan header is pushed on to the packet.
When such packet is sent back to OVS datapath, core
networking stack might not handle it correctly. Following
patch avoids this issue by accelerating the vlan tag
during flow key extract. This simplifies datapath by
bringing uniform packet processing for packets from
all code paths.
Fixes:
5108bbaddc ("openvswitch: add processing of L3 packets").
CC: Jarno Rajahalme <jarno@ovn.org>
CC: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Haishuang Yan [Sun, 25 Dec 2016 06:33:16 +0000 (14:33 +0800)]
ipv4: Namespaceify tcp_tw_reuse knob
Different namespaces might have different requirements to reuse
TIME-WAIT sockets for new connections. This might be required in
cases where different namespace applications are in place which
require TIME_WAIT socket connections to be reduced independently
of the host.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hiromitsu Yamasaki [Tue, 15 Mar 2016 07:07:29 +0000 (16:07 +0900)]
clk: renesas: r8a7796: Add MSIOF controller clocks
This patch adds MSIOF{0,1,2,3} clocks for R8A7796 SoC.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Chris Paterson [Tue, 22 Nov 2016 13:46:02 +0000 (13:46 +0000)]
clk: renesas: r8a7796: Add CAN FD peripheral clock
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Chris Paterson [Tue, 22 Nov 2016 13:46:01 +0000 (13:46 +0000)]
clk: renesas: r8a7796: Add CANFD clock
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Chris Paterson [Tue, 22 Nov 2016 13:46:00 +0000 (13:46 +0000)]
clk: renesas: r8a7796: Add CAN peripheral clock
Based on a patch for r8a7795 by Ramesh Shanmugasundaram.
Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Laura Abbott [Wed, 21 Dec 2016 20:32:54 +0000 (12:32 -0800)]
crypto: testmgr - Use heap buffer for acomp test input
Christopher Covington reported a crash on aarch64 on recent Fedora
kernels:
kernel BUG at ./include/linux/scatterlist.h:140!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 752 Comm: cryptomgr_test Not tainted 4.9.0-11815-ge93b1cc #162
Hardware name: linux,dummy-virt (DT)
task:
ffff80007c650080 task.stack:
ffff800008910000
PC is at sg_init_one+0xa0/0xb8
LR is at sg_init_one+0x24/0xb8
...
[<
ffff000008398db8>] sg_init_one+0xa0/0xb8
[<
ffff000008350a44>] test_acomp+0x10c/0x438
[<
ffff000008350e20>] alg_test_comp+0xb0/0x118
[<
ffff00000834f28c>] alg_test+0x17c/0x2f0
[<
ffff00000834c6a4>] cryptomgr_test+0x44/0x50
[<
ffff0000080dac70>] kthread+0xf8/0x128
[<
ffff000008082ec0>] ret_from_fork+0x10/0x50
The test vectors used for input are part of the kernel image. These
inputs are passed as a buffer to sg_init_one which eventually blows up
with BUG_ON(!virt_addr_valid(buf)). On arm64, virt_addr_valid returns
false for the kernel image since virt_to_page will not return the
correct page. Fix this by copying the input vectors to heap buffer
before setting up the scatterlist.
Reported-by: Christopher Covington <cov@codeaurora.org>
Fixes:
d7db7a882deb ("crypto: acomp - update testmgr with support for acomp")
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Jan Kara [Fri, 21 Oct 2016 09:33:49 +0000 (11:33 +0200)]
ext4: Simplify DAX fault path
Now that dax_iomap_fault() calls ->iomap_begin() without entry lock, we
can use transaction starting in ext4_iomap_begin() and thus simplify
ext4_dax_fault(). It also provides us proper retries in case of ENOSPC.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 19 Oct 2016 12:34:31 +0000 (14:34 +0200)]
dax: Call ->iomap_begin without entry lock during dax fault
Currently ->iomap_begin() handler is called with entry lock held. If the
filesystem held any locks between ->iomap_begin() and ->iomap_end()
(such as ext4 which will want to hold transaction open), this would cause
lock inversion with the iomap_apply() from standard IO path which first
calls ->iomap_begin() and only then calls ->actor() callback which grabs
entry locks for DAX (if it faults when copying from/to user provided
buffers).
Fix the problem by nesting grabbing of entry lock inside ->iomap_begin()
- ->iomap_end() pair.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 19 Oct 2016 12:48:38 +0000 (14:48 +0200)]
dax: Finish fault completely when loading holes
The only case when we do not finish the page fault completely is when we
are loading hole pages into a radix tree. Avoid this special case and
finish the fault in that case as well inside the DAX fault handler. It
will allow us for easier iomap handling.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 15:10:28 +0000 (17:10 +0200)]
dax: Avoid page invalidation races and unnecessary radix tree traversals
Currently dax_iomap_rw() takes care of invalidating page tables and
evicting hole pages from the radix tree when write(2) to the file
happens. This invalidation is only necessary when there is some block
allocation resulting from write(2). Furthermore in current place the
invalidation is racy wrt page fault instantiating a hole page just after
we have invalidated it.
So perform the page invalidation inside dax_iomap_actor() where we can
do it only when really necessary and after blocks have been allocated so
nobody will be instantiating new hole pages anymore.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 15:22:44 +0000 (17:22 +0200)]
mm: Invalidate DAX radix tree entries only if appropriate
Currently invalidate_inode_pages2_range() and invalidate_mapping_pages()
just delete all exceptional radix tree entries they find. For DAX this
is not desirable as we track cache dirtiness in these entries and when
they are evicted, we may not flush caches although it is necessary. This
can for example manifest when we write to the same block both via mmap
and via write(2) (to different offsets) and fsync(2) then does not
properly flush CPU caches when modification via write(2) was the last
one.
Create appropriate DAX functions to handle invalidation of DAX entries
for invalidate_inode_pages2_range() and invalidate_mapping_pages() and
wire them up into the corresponding mm functions.
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Jan Kara [Wed, 10 Aug 2016 14:42:53 +0000 (16:42 +0200)]
ext2: Return BH_New buffers for zeroed blocks
So far we did not return BH_New buffers from ext2_get_blocks() when we
allocated and zeroed-out a block for DAX inode to avoid racy zeroing in
DAX code. This zeroing is gone these days so we can remove the
workaround.
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Thomas Gleixner [Mon, 26 Dec 2016 21:58:20 +0000 (22:58 +0100)]
x86/mce/AMD: Make the init code more robust
If mce_device_init() fails then the mce device pointer is NULL and the
AMD mce code happily dereferences it.
Add a sanity check.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Mon, 26 Dec 2016 21:58:19 +0000 (22:58 +0100)]
smp/hotplug: Undo tglxs brainfart
The attempt to prevent overwriting an active state resulted in a
disaster which effectively disables all dynamically allocated hotplug
states.
Cleanup the mess.
Fixes:
dc280d936239 ("cpu/hotplug: Prevent overwriting of callbacks")
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Al Viro [Mon, 26 Dec 2016 09:10:19 +0000 (04:10 -0500)]
arm64: don't pull uaccess.h into *.S
Split asm-only parts of arm64 uaccess.h into a new header and use that
from *.S.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Florian Fainelli [Sat, 24 Dec 2016 03:56:56 +0000 (19:56 -0800)]
net: korina: Fix NAPI versus resources freeing
Commit
beb0babfb77e ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:
Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.
Fixes:
beb0babfb77e ("korina: disable napi on close and restart")
Reported-by: Alexandros C. Couloumbis <alex@ozo.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann [Wed, 21 Dec 2016 17:04:11 +0000 (18:04 +0100)]
net, sched: fix soft lockup in tc_classify
Shahar reported a soft lockup in tc_classify(), where we run into an
endless loop when walking the classifier chain due to tp->next == tp
which is a state we should never run into. The issue only seems to
trigger under load in the tc control path.
What happens is that in tc_ctl_tfilter(), thread A allocates a new
tp, initializes it, sets tp_created to 1, and calls into tp->ops->change()
with it. In that classifier callback we had to unlock/lock the rtnl
mutex and returned with -EAGAIN. One reason why we need to drop there
is, for example, that we need to request an action module to be loaded.
This happens via tcf_exts_validate() -> tcf_action_init/_1() meaning
after we loaded and found the requested action, we need to redo the
whole request so we don't race against others. While we had to unlock
rtnl in that time, thread B's request was processed next on that CPU.
Thread B added a new tp instance successfully to the classifier chain.
When thread A returned grabbing the rtnl mutex again, propagating -EAGAIN
and destroying its tp instance which never got linked, we goto replay
and redo A's request.
This time when walking the classifier chain in tc_ctl_tfilter() for
checking for existing tp instances we had a priority match and found
the tp instance that was created and linked by thread B. Now calling
again into tp->ops->change() with that tp was successful and returned
without error.
tp_created was never cleared in the second round, thus kernel thinks
that we need to link it into the classifier chain (once again). tp and
*back point to the same object due to the match we had earlier on. Thus
for thread B's already public tp, we reset tp->next to tp itself and
link it into the chain, which eventually causes the mentioned endless
loop in tc_classify() once a packet hits the data path.
Fix is to clear tp_created at the beginning of each request, also when
we replay it. On the paths that can cause -EAGAIN we already destroy
the original tp instance we had and on replay we really need to start
from scratch. It seems that this issue was first introduced in commit
12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining
and avoid kernel panic when we use cls_cgroup").
Fixes:
12186be7d2e1 ("net_cls: fix unconfigured struct tcf_proto keeps chaining and avoid kernel panic when we use cls_cgroup")
Reported-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Tested-by: Shahar Klein <shahark@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 26 Dec 2016 00:13:08 +0000 (16:13 -0800)]
Linux 4.10-rc1
Larry Finger [Fri, 23 Dec 2016 03:06:53 +0000 (21:06 -0600)]
powerpc: Fix build warning on 32-bit PPC
I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:
AS arch/powerpc/kernel/misc_32.o
arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]
This problem is evident after commit
989cea5c14be ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created. That was with commit
9994a33865f4 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").
The offending line does not make a lot of sense. This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.
Thanks to Nicholas Piggin for suggesting this solution.
Fixes:
9994a33865f4 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 25 Dec 2016 22:56:58 +0000 (14:56 -0800)]
avoid spurious "may be used uninitialized" warning
The timer type simplifications caused a new gcc warning:
drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));
despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.
The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.
Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 25 Dec 2016 22:30:04 +0000 (14:30 -0800)]
Merge branch 'timers-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull timer type cleanups from Thomas Gleixner:
"This series does a tree wide cleanup of types related to
timers/timekeeping.
- Get rid of cycles_t and use a plain u64. The type is not really
helpful and caused more confusion than clarity
- Get rid of the ktime union. The union has become useless as we use
the scalar nanoseconds storage unconditionally now. The 32bit
timespec alike storage got removed due to the Y2038 limitations
some time ago.
That leaves the odd union access around for no reason. Clean it up.
Both changes have been done with coccinelle and a small amount of
manual mopping up"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Get rid of ktime_equal()
ktime: Cleanup ktime_set() usage
ktime: Get rid of the union
clocksource: Use a plain u64 instead of cycle_t
Linus Torvalds [Sun, 25 Dec 2016 22:05:56 +0000 (14:05 -0800)]
Merge branch 'smp-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull SMP hotplug notifier removal from Thomas Gleixner:
"This is the final cleanup of the hotplug notifier infrastructure. The
series has been reintgrated in the last two days because there came a
new driver using the old infrastructure via the SCSI tree.
Summary:
- convert the last leftover drivers utilizing notifiers
- fixup for a completely broken hotplug user
- prevent setup of already used states
- removal of the notifiers
- treewide cleanup of hotplug state names
- consolidation of state space
There is a sphinx based documentation pending, but that needs review
from the documentation folks"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/armada-xp: Consolidate hotplug state space
irqchip/gic: Consolidate hotplug state space
coresight/etm3/4x: Consolidate hotplug state space
cpu/hotplug: Cleanup state names
cpu/hotplug: Remove obsolete cpu hotplug register/unregister functions
staging/lustre/libcfs: Convert to hotplug state machine
scsi/bnx2i: Convert to hotplug state machine
scsi/bnx2fc: Convert to hotplug state machine
cpu/hotplug: Prevent overwriting of callbacks
x86/msr: Remove bogus cleanup from the error path
bus: arm-ccn: Prevent hotplug callback leak
perf/x86/intel/cstate: Prevent hotplug callback leak
ARM/imx/mmcd: Fix broken cpu hotplug handling
scsi: qedi: Convert to hotplug state machine
Linus Torvalds [Sun, 25 Dec 2016 22:01:28 +0000 (14:01 -0800)]
Merge branch 'turbostat' of git://git./linux/kernel/git/lenb/linux
Pull turbostat updates from Len Brown.
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: remove obsolete -M, -m, -C, -c options
tools/power turbostat: Make extensible via the --add parameter
tools/power turbostat: Denverton uses a 25 MHz crystal, not 19.2 MHz
tools/power turbostat: line up headers when -M is used
tools/power turbostat: fix SKX PKG_CSTATE_LIMIT decoding
tools/power turbostat: Support Knights Mill (KNM)
tools/power turbostat: Display HWP OOB status
tools/power turbostat: fix Denverton BCLK
tools/power turbostat: use intel-family.h model strings
tools/power/turbostat: Add Denverton RAPL support
tools/power/turbostat: Add Denverton support
tools/power/turbostat: split core MSR support into status + limit
tools/power turbostat: fix error case overflow read of slm_freq_table[]
tools/power turbostat: Allocate correct amount of fd and irq entries
tools/power turbostat: switch to tab delimited output
tools/power turbostat: Gracefully handle ACPI S3
tools/power turbostat: tidy up output on Joule counter overflow
Nicholas Piggin [Sun, 25 Dec 2016 03:00:30 +0000 (13:00 +1000)]
mm: add PageWaiters indicating tasks are waiting for a page bit
Add a new page flag, PageWaiters, to indicate the page waitqueue has
tasks waiting. This can be tested rather than testing waitqueue_active
which requires another cacheline load.
This bit is always set when the page has tasks on page_waitqueue(page),
and is set and cleared under the waitqueue lock. It may be set when
there are no tasks on the waitqueue, which will cause a harmless extra
wakeup check that will clears the bit.
The generic bit-waitqueue infrastructure is no longer used for pages.
Instead, waitqueues are used directly with a custom key type. The
generic code was not flexible enough to have PageWaiters manipulation
under the waitqueue lock (which simplifies concurrency).
This improves the performance of page lock intensive microbenchmarks by
2-3%.
Putting two bits in the same word opens the opportunity to remove the
memory barrier between clearing the lock bit and testing the waiters
bit, after some work on the arch primitives (e.g., ensuring memory
operand widths match and cover both bits).
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nicholas Piggin [Sun, 25 Dec 2016 03:00:29 +0000 (13:00 +1000)]
mm: Use owner_priv bit for PageSwapCache, valid when PageSwapBacked
A page is not added to the swap cache without being swap backed,
so PageSwapBacked mappings can use PG_owner_priv_1 for PageSwapCache.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Bob Peterson <rpeterso@redhat.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Andrew Lutomirski <luto@kernel.org>
Cc: Andreas Gruenbacher <agruenba@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thomas Gleixner [Sun, 25 Dec 2016 11:43:07 +0000 (12:43 +0100)]
ktime: Get rid of ktime_equal()
No point in going through loops and hoops instead of just comparing the
values.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>