Archit Taneja [Fri, 9 Oct 2015 09:51:12 +0000 (15:21 +0530)]
drm/msm/dsi: Parse bus clocks from a list
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 9 Oct 2015 07:10:39 +0000 (12:40 +0530)]
drm/msm/dsi: Delay dsi_clk_init
Initialize clocks only after we get the DSI host version. This will allow
us to get clocks using a pre-defined list based on the DSI major/minor
version of the host. This is required since clock requirements of
different major DSI revisions(v2 vs 6g) aren't the same.
Modify dsi_get_version to get the interface clock, and then put it after
it is used.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 9 Oct 2015 05:40:59 +0000 (11:10 +0530)]
drm/msm/dsi: Use a better way to figure out DSI version
The current version checking mechanism works fine for DSI6G blocks. It
doesn't work so well for older generation DSIv2 blocks.
The initial read of REG_DSI_6G_HW_VERSION(offset 0x0) would result in a
read of REG_DSI_CTRL for DSIv2. This register won't necessarily be 0 on
DSIv2. It can be non zero if DSI was previously initialized by the
bootloader.
Instead of reading offset 0x0, we now read offset 0x1f0. For DSIv2, this
register is DSI_VERSION, and is bound to be non-zero. On DSI6G, this
register(offset 0x1f0) is SCRATCH_REGISTER_0, which no one ever seems to
touch, and from all register dumps I'vc seen, holds 0 all the time.
Modify dsi_get_version to read REG_DSI_VERSION to determine whether we
are DSI6G or DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 14 Oct 2015 06:33:44 +0000 (12:03 +0530)]
drm/msm/dsi: Add DSI PLL for 28nm 8960 PHY
Add DSI PLL common clock framework clocks for 8960 PHY.
The PLL here is different from the ones found in B family msm chips. As
before, the DSI provides two clocks to the outside world. dsixpll and
dsixpllbyte (x = 1, 2). dsixpll is a regular clock divider, but
dsixpllbyte is modelled as a custom clock divider.
dsixpllbyte is the starting point of the PLL configuration. It is the
one that sets up the VCO clock rate. We need the VCO clock rate in the
form: F * byteclk, where F is a multiplication factor that varies on
the byte clock the DSI driver is trying to set. We use the custom
clk_ops for dsixpllbyte to ensure that the parent (VCO) is set at this
rate.
An additional divider (POSTDIV1) generates the bitclk. Since bit clock
can be derived from byteclock, we calculate it internally, and don't
expose it as a clock.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 14 Oct 2015 06:30:34 +0000 (12:00 +0530)]
drm/msm/dsi: Add support for 28nm PHY on 8960
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 30 Nov 2015 12:17:17 +0000 (17:47 +0530)]
drm/msm/dsi: Don't get byte/pixel source clocks from DT
We retrieve the byte and pixel source clocks (RCG clocks) in the dsi
driver via DT. These are needed so that we can re-parent these source
clocks if we want to drive it using a different DSI PLL.
We shouldn't get these via DT because they aren't clocks that directly
serve as inputs to the dsi host.
Fortunately, there is a static parent-child link between the
byte_clk_src/pixel_clk_src and byte_clk/pixel_clk clocks. So, we can
retrieve the source clocks via clk_get_parent.
Do this instead of retrieving via DT.
Cc: Rob Herring <robh@kernel.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 12:28:28 +0000 (17:58 +0530)]
drm/msm/mdp4: Initialize DSI encoders
Create DSI encoders during modeset_init. The 2 encoders should ideally be
one command mode and one video mode DSI encoder respectively, but we don't
support command mode yet. We just create 2 of the same because the dsi
driver expects it, we end up using only the first one.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 12:27:16 +0000 (17:57 +0530)]
drm/msm/mdp4: Call custom round_pixclk helper only if the encoder type is TMDS
The mdp_kms round_pixclk op creates problems when we have more
interfaces in use. It calls the DTV encoder's helper by default.
Check on encoder type and call the corresponding encoder's
func meant for rounding pixel clock. DSI and LVDS don't require
rounding, so just return rate in their case.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Vinay Simha BN [Mon, 19 Oct 2015 06:57:11 +0000 (12:27 +0530)]
drm/msm/dsi: Add a mdp4 encoder for DSI
Create an mdp4 incoder for DSI. Only DSI video mode is supported as of
now.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Vinay Simha BN <vinaysimha@inforcecomputing.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 11:45:50 +0000 (17:15 +0530)]
drm/msm/mdp4: Initialize LCDC encoder even if panel driver isn't available
Currently, the driver defers if it doesn't find a drm_panel. This forces
us to have a drm_panel, if not, the driver isn't usable.
Make the lcdc encoder initialization independent of the availability of
the drm panel. We only check if there is a panel node specified in DT. If
it isn't, then we don't initialize the encoder at all. The panel node is
passed to the lcdc encoder and lvds connector drivers.
The connector driver takes the responsibility to retrieve the drm_panel
from the panel node, and update the status on whether the panel is
connected or not. This makes the panel usable even if the drm_panel
driver is inserted as a module later on.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 19 Oct 2015 06:50:52 +0000 (12:20 +0530)]
drm/msm/mdp4: Clean up modeset_init
modeset_init() for mdp4 isn't very flexible. That makes it hard to add
more interfaces.
Split out the encoder/connector creation code in modeset_init into a
separate function. This is similar to what's done in modeset_init for
mdp5.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 11:02:28 +0000 (16:32 +0530)]
drm/msm/adreno: Remove CONFIG_OF checks
Remove CONFIG_OF checks in adreno_device.c. The downstream bus scaling
stuff is included only when CONFIG_OF is not set. So, remove that too.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Fri, 30 Oct 2015 07:05:55 +0000 (12:35 +0530)]
drm/msm/hdmi: remove CONFIG_OF checks
We now only care about kernels that support DT. Remote the non-DT stuff.
While we're at it, use of_device_get_match_data to retrieve match data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 07:14:52 +0000 (12:44 +0530)]
drm/msm/mdp: Remove CONFIG_OF checks from MDP drivers
We don't intend to use downstream non-DT kernels anymore, so remove
CONFIG_OF checks.
Update the TODO comment so that we don't forget about max_clk setting
for non APQ8064 chips having MDP4.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 07:06:19 +0000 (12:36 +0530)]
dt-bindings: drm/msm: Update MDP bindings
Update DT bindings for mdp. We now have a more uniform and future-proof
set of compatible strings.
MDP5 bindings were missing. Add those and update details on the
clock-names properties.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 06:58:39 +0000 (12:28 +0530)]
drm/msm: Update compatible strings for mdp
Create distinct compatible strings for mdp4 and mdp5. Keep "qcom,mdss_mdp"
as is to support downstream kernels.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Wed, 18 Nov 2015 06:45:14 +0000 (12:15 +0530)]
drm/msm: Remove non-DT code in msm_drv
Support for non-DT kernels was mainly to use v3.4 downstream kernels.
This is no longer a priority now as we have reasonable support upstream.
Remove CONFIG_OF from the top level msm_drv.c file. While we're at it,
clean up the data matching process using of_device_get_match_data.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Archit Taneja [Mon, 26 Oct 2015 09:13:57 +0000 (14:43 +0530)]
drm/msm/mdp5: high precision vblank timestamp support
MDP5 has line count and frame count registers for each interface. Enable
these counters and use them to implement the get_vblank_timestamp drm
driver op.
The line counter starts with the value 1 at the beginning of the VSYNC
pulse and ends with value VTOTAL at the end of VFP. This value is used
to determine whether we're in blanking period or not, and an adjusted
value of this counter is used to get vpos as expected by
get_scanout_position. Since there is no way to calculate hpos, we always
set it to 0.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Dave Airlie [Fri, 11 Dec 2015 03:46:05 +0000 (13:46 +1000)]
Merge branch 'drm-header-fixes' of https://github.com/GabrielL/linux into drm-next
Fix all the problems with the header files and userspace builds
off them. I really care so little about this, but hey who am
I to stop progress.
* 'drm-header-fixes' of https://github.com/GabrielL/linux: (30 commits)
drm: fix inclusion of drm.h in via_drm.h
drm: fix inclusion of drm.h in vmwgfx_drm.h
drm: fix inclusion of drm.h in virtgpu_drm.h
drm: fix inclusion of drm.h in tegra_drm.h
drm: fix inclusion of drm.h in savage_drm.h
drm: fix inclusion of drm.h in r128_drm.h
drm: fix inclusion of drm.h in qxl_drm.h
drm: fix inclusion of drm.h in omap_drm.h
drm: fix inclusion of drm.h in msm_drm.h
drm: fix inclusion of drm.h in mga_drm.h
drm: fix inclusion of drm.h in exynos_sarea.h
drm: fix inclusion of drm.h in i810_drm.h
drm: fix inclusion of drm.h in exynos_sarea.h
drm: fix inclusion of drm.h in drm_sarea.h
drm: drm_mode.h fix includes
drm: drm_fourcc.h fix includes
drm: include drm.h in armada_drm.h
include/uapi/drm/amdgpu_drm.h: use __u32 and __u64 from <linux/types.h>
drm: Kbuild: add admgpu_drm.h to the installed headers
drm: use __u{32,64} instead of uint{32,64}_t in virtgpu_drm.h
...
Gabriel Laskar [Mon, 30 Nov 2015 14:10:57 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in via_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:56 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in vmwgfx_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:55 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in virtgpu_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:54 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in tegra_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:53 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in savage_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:52 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in r128_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:51 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in qxl_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:50 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in omap_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:49 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in msm_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:48 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in mga_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:47 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in exynos_sarea.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:46 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in i810_drm.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for
the libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:45 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in exynos_sarea.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:44 +0000 (15:10 +0100)]
drm: fix inclusion of drm.h in drm_sarea.h
Using `#include "drm.h"` instead of `#include <drm/drm.h>` allow drm
headers to be moved in another directory without changes, like for the
libdrm imports.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:43 +0000 (15:10 +0100)]
drm: drm_mode.h fix includes
Instead of using linux/types.h, drm headers should use drm.h, in order
to handle the portability issues in only one place.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:42 +0000 (15:10 +0100)]
drm: drm_fourcc.h fix includes
Instead of using linux/types.h, drm headers should use drm.h, in order
to handle the portability issues in only one place.
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:41 +0000 (15:10 +0100)]
drm: include drm.h in armada_drm.h
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Wed, 2 Dec 2015 22:44:33 +0000 (23:44 +0100)]
include/uapi/drm/amdgpu_drm.h: use __u32 and __u64 from <linux/types.h>
Kernel headers exported to userspace are supposed to use these.
Fixes compilation errors in userspace:
error: unknown type name ‘uint64_t’
error: unknown type name ‘uint32_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:40 +0000 (15:10 +0100)]
drm: Kbuild: add admgpu_drm.h to the installed headers
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Gabriel Laskar [Mon, 30 Nov 2015 14:10:39 +0000 (15:10 +0100)]
drm: use __u{32,64} instead of uint{32,64}_t in virtgpu_drm.h
Signed-off-by: Gabriel Laskar <gabriel@lse.epita.fr>
Reviewed-by: Emil Velikov <emil.l.velikov@gmail.com>
CC: Emil Velikov <emil.l.velikov@gmail.com>
CC: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 1 Feb 2015 14:10:41 +0000 (15:10 +0100)]
include/uapi/linux/agpgart.h: include stdlib.h in userspace
Fixes userspace compiler error:
error: unknown type name ‘size_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Wed, 2 Dec 2015 22:17:47 +0000 (23:17 +0100)]
include/uapi/linux/virtio_gpu.h: use __u8 from <linux/types.h>
Kernel headers exported to userspace are should these types.
Fixes userspace compilation error:
error: unknown type name ‘uint8_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Wed, 11 Mar 2015 02:12:23 +0000 (03:12 +0100)]
include/uapi/drm/qxl_drm.h: use __s32, __u32 and __u64 from linux/types.h
Fixes userspace compilation errors like:
error: unknown type name ‘uint32_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Wed, 11 Mar 2015 02:07:51 +0000 (03:07 +0100)]
include/uapi/drm/vmwgfx_drm.h: use __s32, __u32 and __u64 from linux/types.h
Fixes userspace compilation errors like:
error: unknown type name ‘uint32_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 31 Aug 2014 14:20:20 +0000 (16:20 +0200)]
via_drm.h: don't include non-existing via_drmclient.h
Fixes compiler error:
drm/via_drm.h:36:27: fatal error: via_drmclient.h: No such file or directory
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 31 Aug 2014 11:11:54 +0000 (13:11 +0200)]
radeon_drm.h: use __u32 and __u64 from linux/types.h
Fixes userspace compiler error:
drm/radeon_drm.h:794:2: error: unknown type name ‘uint64_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 31 Aug 2014 11:09:51 +0000 (13:09 +0200)]
nouveau_drm.h: use __u32 and __u64 from linux/types.h
Fixes userspace compilation errors like:
drm/nouveau_drm.h:41:2: error: unknown type name ‘uint32_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 31 Aug 2014 11:07:31 +0000 (13:07 +0200)]
exynos_drm.h: use __u64 from linux/types.h
Fixes userspace compilation error:
drm/exynos_drm.h:30:2: error: unknown type name ‘uint64_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 31 Aug 2014 11:01:09 +0000 (13:01 +0200)]
drm_mode.h: use __u32 and __u64 from linux/types.h
Fixes userspace compilation error:
drm/drm_mode.h:472:2: error: unknown type name ‘uint32_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Mikko Rapeli [Sun, 31 Aug 2014 10:58:46 +0000 (12:58 +0200)]
drm.h: use __kernel_size_t instead of size_t
Fall back to size_t for non Linux platforms.
Fixes userspace compilation error:
drm/drm.h:132:2: error: unknown type name ‘size_t’
Signed-off-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Dave Airlie [Tue, 8 Dec 2015 01:04:26 +0000 (11:04 +1000)]
Back merge tag 'v4.4-rc4' into drm-next
We've picked up a few conflicts and it would be nice
to resolve them before we move onwards.
Dave Airlie [Mon, 7 Dec 2015 08:17:09 +0000 (18:17 +1000)]
Merge tag 'topic/drm-misc-2015-12-04' of git://anongit.freedesktop.org/drm-intel into drm-next
New -misc pull. Big thing is Thierry's atomic helpers for system suspend
resume, which I'd like to use in i915 too. Hence the pull.
* tag 'topic/drm-misc-2015-12-04' of git://anongit.freedesktop.org/drm-intel:
drm: keep connector status change logging human readable
drm/atomic-helper: Reject attempts at re-stealing encoders
drm/atomic-helper: Implement subsystem-level suspend/resume
drm: Implement drm_modeset_lock_all_ctx()
drm/gma500: Add driver private mutex for the fault handler
drm/gma500: Drop dev->struct_mutex from mmap offset function
drm/gma500: Drop dev->struct_mutex from fbdev init/teardown code
drm/gma500: Drop dev->struct_mutex from modeset code
drm/gma500: Use correct unref in the gem bo create function
drm/edid: Make the detailed timing CEA/HDMI mode fixup accept up to 5kHz clock difference
drm/atomic_helper: Add drm_atomic_helper_disable_planes_on_crtc()
drm: Serialise multiple event readers
drm: Drop dev->event_lock spinlock around faulting copy_to_user()
Linus Torvalds [Sun, 6 Dec 2015 23:43:12 +0000 (15:43 -0800)]
Linux 4.4-rc4
James Simmons [Fri, 4 Dec 2015 23:23:08 +0000 (18:23 -0500)]
staging/lustre: remove IOC_LIBCFS_PING_TEST ioctl
The ioctl IOC_LIBCFS_PING_TEST has not been used in ages. The recent
nidstring changes which moved all the nidstring operations from libcfs
to the LNet layer but this ioctl code was still using an nidstring
operation that was causing a circular dependency loop between libcfs and
LNet.
Signed-off-by: James Simmons <jsimmons@infradead.org>
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 6 Dec 2015 21:51:49 +0000 (13:51 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes (-stable fodder) + dead code removal after the
overlayfs fix.
I agree that it's better to separate from the fix part to make
backporting easier, but IMO it's not worth delaying said dead code
removal until the next window"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
ovl: get rid of the dead code left from broken (and disabled) optimizations
ovl: fix permission checking for setattr
Al Viro [Sun, 6 Dec 2015 17:33:02 +0000 (12:33 -0500)]
Don't reset ->total_link_count on nested calls of vfs_path_lookup()
we already zero it on outermost set_nameidata(), so initialization in
path_init() is pointless and wrong. The same DoS exists on pre-4.2
kernels, but there a slightly different fix will be needed.
Cc: stable@vger.kernel.org # v4.2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Al Viro [Sun, 6 Dec 2015 17:31:07 +0000 (12:31 -0500)]
ovl: get rid of the dead code left from broken (and disabled) optimizations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Miklos Szeredi [Fri, 4 Dec 2015 18:18:48 +0000 (19:18 +0100)]
ovl: fix permission checking for setattr
[Al Viro] The bug is in being too enthusiastic about optimizing ->setattr()
away - instead of "copy verbatim with metadata" + "chmod/chown/utimes"
(with the former being always safe and the latter failing in case of
insufficient permissions) it tries to combine these two. Note that copyup
itself will have to do ->setattr() anyway; _that_ is where the elevated
capabilities are right. Having these two ->setattr() (one to set verbatim
copy of metadata, another to do what overlayfs ->setattr() had been asked
to do in the first place) combined is where it breaks.
Signed-off-by: Miklos Szeredi <miklos@szeredi.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds [Sun, 6 Dec 2015 16:35:05 +0000 (08:35 -0800)]
Merge branch 'sched-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"This updates contains the following changes:
- Fix a signal handling regression in the bit wait functions.
- Avoid false positive warnings in the wakeup path.
- Initialize the scheduler root domain properly.
- Handle gtime calculations in proc/$PID/stat proper.
- Add more documentation for the barriers in try_to_wake_up().
- Fix a subtle race in try_to_wake_up() which might cause a task to
be scheduled on two cpus
- Compile static helper function only when it is used"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
sched/core: Better document the try_to_wake_up() barriers
sched/cputime: Fix invalid gtime in proc
sched/core: Clear the root_domain cpumasks in init_rootdomain()
sched/core: Remove false-positive warning from wake_up_process()
sched/wait: Fix signal handling in bit wait helpers
sched/rt: Hide the push_irq_work_func() declaration
Linus Torvalds [Sun, 6 Dec 2015 16:08:56 +0000 (08:08 -0800)]
Merge branch 'x86-urgent-for-linus' of git://git./linux/kernel/git/tip/tip
Pull x86 fixes from Thoma Gleixner:
"Another round of fixes for x86:
- Move the initialization of the microcode driver to late_initcall to
make sure everything that init function needs is available.
- Make sure that lockdep knows about interrupts being off in the
entry code before calling into c-code.
- Undo the cpu hotplug init delay regression.
- Use the proper conditionals in the mpx instruction decoder.
- Fixup restart_syscall for x32 tasks.
- Fix the hugepage regression on PAE kernels which was introduced
with the latest PAT changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/signal: Fix restart_syscall number for x32 tasks
x86/mpx: Fix instruction decoder condition
x86/mm: Fix regression with huge pages on PAE
x86 smpboot: Re-enable init_udelay=0 by default on modern CPUs
x86/entry/64: Fix irqflag tracing wrt context tracking
x86/microcode: Initialize the driver late when facilities are up
Linus Torvalds [Sun, 6 Dec 2015 16:02:25 +0000 (08:02 -0800)]
Merge tag 'scsi-fixes' of git://git./linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is quite a bumper crop of fixes: three from Arnd correcting
various build issues in some configurations, a lock recursion in
qla2xxx. Two potentially exploitable issues in hpsa and mvsas, a
potential null deref in st, a revert of a bdi registration fix that
turned out to cause even more problems, a set of fixes to allow people
who only defined MPT2SAS to still work after the mpt2/mpt3sas merger
and a couple of fixes for issues turned up by the hyper-v storvsc
driver"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
mpt3sas: fix Kconfig dependency problem for mpt2sas back compatibility
Revert "scsi: Fix a bdi reregistration race"
mpt3sas: Add dummy Kconfig option for backwards compatibility
Fix a memory leak in scsi_host_dev_release()
block/sd: Fix device-imposed transfer length limits
scsi_debug: fix prevent_allow+verify regressions
MAINTAINERS: Add myself as co-maintainer of the SCSI subsystem.
sd: Make discard granularity match logical block size when LBPRZ=1
scsi: hpsa: select CONFIG_SCSI_SAS_ATTR
scsi: advansys needs ISA dma api for ISA support
scsi_sysfs: protect against double execution of __scsi_remove_device()
st: fix potential null pointer dereference.
scsi: report 'INQUIRY result too short' once per host
advansys: fix big-endian builds
qla2xxx: Fix rwlock recursion
hpsa: logical vs bitwise AND typo
mvsas: don't allow negative timeouts
mpt3sas: Fix use sas_is_tlr_enabled API before enabling MPI2_SCSIIO_CONTROL_TLR_ON flag
Linus Torvalds [Sun, 6 Dec 2015 00:06:30 +0000 (16:06 -0800)]
Merge branch 'drm-fixes' of git://people.freedesktop.org/~airlied/linux
Pull drm fixes from Dave Airlie:
"A bunch of change across the board, the main things are some vblank
fallout in radeon and nouveau required some work, but I think this
should fix it all. There is also one drm fix for an oops in vmwgfx
with how we pass the drm master around.
The rest is just some amdgpu, i915, imx and rockchip fixes.
Probably more than I'd like at this point, but hopefully things settle
down now"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (40 commits)
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/nouveau: Fix pre-nv50 pageflip events (v4)
drm: Fix an unwanted master inheritance v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/rockchip: Use CRTC vblank event interface
drm/rockchip: Fix module autoload for OF platform driver
drm/rockchip: vop: fix window origin calculation
...
Linus Torvalds [Sat, 5 Dec 2015 18:46:44 +0000 (10:46 -0800)]
Merge branch 'linus' of git://git./linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
"This fixes a couple of crypto drivers that were using memcmp to verify
authentication tags. They now use crypto_memneq instead"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: talitos - Fix timing leak in ESP ICV verification
crypto: nx - Fix timing leak in GCM and CCM decryption
Dmitry V. Levin [Mon, 30 Nov 2015 21:54:36 +0000 (00:54 +0300)]
x86/signal: Fix restart_syscall number for x32 tasks
When restarting a syscall with regs->ax == -ERESTART_RESTARTBLOCK,
regs->ax is assigned to a restart_syscall number. For x32 tasks, this
syscall number must have __X32_SYSCALL_BIT set, otherwise it will be
an x86_64 syscall number instead of a valid x32 syscall number. This
issue has been there since the introduction of x32.
Reported-by: strace/tests/restart_syscall.test
Reported-and-tested-by: Elvira Khabirova <lineprinter0@gmail.com>
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Cc: Elvira Khabirova <lineprinter0@gmail.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20151130215436.GA25996@altlinux.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dave Hansen [Tue, 1 Dec 2015 00:31:13 +0000 (16:31 -0800)]
x86/mpx: Fix instruction decoder condition
MPX decodes instructions in order to tell which bounds register
was violated. Part of this decoding involves looking at the "REX
prefix" which is a special instrucion prefix used to retrofit
support for new registers in to old instructions.
The X86_REX_*() macros are defined to return actual bit values:
#define X86_REX_R(rex) ((rex) & 4)
*not* boolean values. However, the MPX code was checking for
them like they were booleans. This might have led to us
mis-decoding the "REX prefix" and giving false information out to
userspace about bounds violations. X86_REX_B() actually is bit 1,
so this is really only broken for the X86_REX_X() case.
Fix the conditionals up to tolerate the non-boolean values.
Fixes:
fcc7ffd67991 "x86, mpx: Decode MPX instruction to get bound violation information"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: x86@kernel.org
Cc: Dave Hansen <dave@sr71.net>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/20151201003113.D800C1E0@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dave Airlie [Sat, 5 Dec 2015 06:15:38 +0000 (16:15 +1000)]
Merge branch 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux into drm-next
A few more last minute fixes for 4.4 on top of my pull request from
earlier this week. The big change here is a vblank regression fix due to
commit
4dfd6486 "drm: Use vblank timestamps to guesstimate how many vblanks
were missed". Beyond that, a hotplug fix and a few VM fixes.
* 'drm-fixes-4.4' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
drm/amdgpu: add spin lock to protect freed list in vm (v2)
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
drm/amdgpu: take a BO reference for the user fence
drm/amdgpu: take a BO reference in the display code
drm/amdgpu: set snooped flags only on system addresses v2
drm/amdgpu: fix race condition in amd_sched_entity_push_job
drm/amdgpu: add err check for pin userptr
add blacklist for thinkpad T40p
drm/amdgpu: fix VM page table reference counting
drm/amdgpu: fix userptr flags check
Linus Torvalds [Fri, 4 Dec 2015 20:46:07 +0000 (12:46 -0800)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
Pull Ceph fix from Sage Weil:
"This addresses a refcounting bug that leads to a use-after-free"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't put snap_context twice in rbd_queue_workfn()
Alex Deucher [Thu, 3 Dec 2015 17:31:56 +0000 (12:31 -0500)]
drm/amdgpu: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v3)
commit
4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Maybe replace the udelay() in the flip_work_func() by a suitable
usleep_range() for a bit better efficiency? Will try that.
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Probably fixes: fdo#93147
Port of Mario's radeon fix to amdgpu.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(v1) Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v2) Refine amdgpu_flip_work_func() for better efficiency.
In amdgpu_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Also small fix to code comment and formatting in that function.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
(v3) Fix crash in crtc disabled case
Linus Torvalds [Fri, 4 Dec 2015 19:30:45 +0000 (11:30 -0800)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- NFIT parsing regression fixes from Linda. The nvdimm hot-add
implementation merged in 4.4-rc1 interpreted the specification in a
way that breaks actual HPE platforms. We are also closing the loop
with the ACPI Working Group to get this clarification added to the
spec.
- Andy pointed out that his laptop without nvdimm resources is loading
the e820-nvdimm module by default, fix that up to only load the
module when an e820-type-12 range is present.
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: Adjust for different _FIT and NFIT headers
nfit: Fix the check for a successful NFIT merge
nfit: Account for table size length variation
libnvdimm, e820: skip module loading when no type-12
Linus Torvalds [Fri, 4 Dec 2015 18:17:20 +0000 (10:17 -0800)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull ARM KVM fixes from Paolo Bonzini:
- a series of fixes to deal with the aliasing between the sp and xzr
register
- a fix for the cache flush fix that went in -rc3
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
ARM/arm64: KVM: correct PTE uncachedness check
arm64: KVM: Get rid of old vcpu_reg()
arm64: KVM: Correctly handle zero register in system register accesses
arm64: KVM: Remove const from struct sys_reg_params
arm64: KVM: Correctly handle zero register during MMIO
Mario Kleiner [Wed, 25 Nov 2015 19:14:31 +0000 (20:14 +0100)]
drm/radeon: Fixup hw vblank counter/ts for new drm_update_vblank_count() (v2)
commit
4dfd6486 "drm: Use vblank timestamps to guesstimate how many
vblanks were missed" introduced in Linux 4.4-rc1 makes the drm core
more fragile to drivers which don't update hw vblank counters and
vblank timestamps in sync with firing of the vblank irq and
essentially at leading edge of vblank.
This exposed a problem with radeon-kms/amdgpu-kms which do not
satisfy above requirements:
The vblank irq fires a few scanlines before start of vblank, but
programmed pageflips complete at start of vblank and
vblank timestamps update at start of vblank, whereas the
hw vblank counter increments only later, at start of vsync.
This leads to problems like off by one errors for vblank counter
updates, vblank counters apparently going backwards or vblank
timestamps apparently having time going backwards. The net result
is stuttering of graphics in games, or little hangs, as well as
total failure of timing sensitive applications.
See bug #93147 for an example of the regression on Linux 4.4-rc:
https://bugs.freedesktop.org/show_bug.cgi?id=93147
This patch tries to align all above events better from the
viewpoint of the drm core / of external callers to fix the problem:
1. The apparent start of vblank is shifted a few scanlines earlier,
so the vblank irq now always happens after start of this extended
vblank interval and thereby drm_update_vblank_count() always samples
the updated vblank count and timestamp of the new vblank interval.
To achieve this, the reporting of scanout positions by
radeon_get_crtc_scanoutpos() now operates as if the vblank starts
radeon_crtc->lb_vblank_lead_lines before the real start of the hw
vblank interval. This means that the vblank timestamps which are based
on these scanout positions will now update at this earlier start of
vblank.
2. The driver->get_vblank_counter() function will bump the returned
vblank count as read from the hw by +1 if the query happens after
the shifted earlier start of the vblank, but before the real hw increment
at start of vsync, so the counter appears to increment at start of vblank
in sync with the timestamp update.
3. Calls from vblank irq-context and regular non-irq calls are now
treated identical, always simulating the shifted vblank start, to
avoid inconsistent results for queries happening from vblank irq vs.
happening from drm_vblank_enable() or vblank_disable_fn().
4. The radeon_flip_work_func will delay mmio programming a pageflip until
the start of the real vblank iff it happens to execute inside the shifted
earlier start of the vblank, so pageflips now also appear to execute at
start of the shifted vblank, in sync with vblank counter and timestamp
updates. This to avoid some races between updates of vblank count and
timestamps that are used for swap scheduling and pageflip execution which
could cause pageflips to execute before the scheduled target vblank.
The lb_vblank_lead_lines "fudge" value is calculated as the size of
the display controllers line buffer in scanlines for the given video
mode: Vblank irq's are triggered by the line buffer logic when the line
buffer refill for a video frame ends, ie. when the line buffer source read
position enters the hw vblank. This means that a vblank irq could fire at
most as many scanlines before the current reported scanout position of the
crtc timing generator as the number of scanlines the line buffer can
maximally hold for a given video mode.
This patch has been successfully tested on a RV730 card with DCE-3 display
engine and on a evergreen card with DCE-4 display engine, in single-display
and dual-display configuration, with different video modes.
A similar patch is needed for amdgpu-kms to fix the same problem.
Limitations:
- Line buffer sizes in pixels are hard-coded on < DCE-4 to a value
i just guessed to be high enough to work ok, lacking info on the true
sizes atm.
Fixes: fdo#93147
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Michel Dänzer <michel.daenzer@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
(v1) Tested-by: Dave Witbrodt <dawitbro@sbcglobal.net>
(v2) Refine radeon_flip_work_func() for better efficiency:
In radeon_flip_work_func, replace the busy waiting udelay(5)
with event lock held by a more performance and energy efficient
usleep_range() until at least predicted true start of hw vblank,
with some slack for scheduler happiness. Release the event lock
during waits to not delay other outputs in doing their stuff, as
the waiting can last up to 200 usecs in some cases.
Retested on DCE-3 and DCE-4 to verify it still works nicely.
(v2) Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lyude [Thu, 3 Dec 2015 23:26:07 +0000 (18:26 -0500)]
drm/radeon: Retry DDC probing on DVI on failure if we got an HPD interrupt
HPD signals on DVI ports can be fired off before the pins required for
DDC probing actually make contact, due to the pins for HPD making
contact first. This results in a HPD signal being asserted but DDC
probing failing, resulting in hotplugging occasionally failing.
This is somewhat rare on most cards (depending on what angle you plug
the DVI connector in), but on some cards it happens constantly. The
Radeon R5 on the machine used for testing this patch for instance, runs
into this issue just about every time I try to hotplug a DVI monitor and
as a result hotplugging almost never works.
Rescheduling the hotplug work for a second when we run into an HPD
signal with a failing DDC probe usually gives enough time for the rest
of the connector's pins to make contact, and fixes this issue.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Lyude <cpaul@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
jimqu [Fri, 4 Dec 2015 09:17:00 +0000 (17:17 +0800)]
drm/amdgpu: add spin lock to protect freed list in vm (v2)
there is a protection fault about freed list when OCL test.
add a spin lock to protect it.
v2: drop changes in vm_fini
Signed-off-by: JimQu <jim.qu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Christian König [Thu, 3 Dec 2015 19:54:35 +0000 (20:54 +0100)]
drm/amdgpu: partially revert "drm/amdgpu: fix VM_CONTEXT*_PAGE_TABLE_END_ADDR" v2
The gtt_end is already inclusive, we don't need to subtract one here.
v2 (chk): keep the fix for the VM code, cause here it really applies.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Anatoli Antonovitch <anatoli.antonovitch@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 3 Dec 2015 18:55:52 +0000 (19:55 +0100)]
drm/amdgpu: take a BO reference for the user fence
No need for a GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Christian König [Thu, 3 Dec 2015 18:55:51 +0000 (19:55 +0100)]
drm/amdgpu: take a BO reference in the display code
No need for the GEM reference here.
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Paolo Bonzini [Fri, 4 Dec 2015 17:32:32 +0000 (18:32 +0100)]
Merge tag 'kvm-arm-for-v4.4-rc4' of git://git./linux/kernel/git/kvmarm/kvmarm into kvm-master
KVM/ARM fixes for v4.4-rc4
- A series of fixes to deal with the aliasing between the sp and xzr register
- A fix for the cache flush fix that went in -rc3
Christian König [Fri, 4 Dec 2015 12:32:55 +0000 (13:32 +0100)]
drm/amdgpu: set snooped flags only on system addresses v2
Not necessary for VRAM.
v2: no need to check if ttm is NULL.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Linus Torvalds [Fri, 4 Dec 2015 17:16:26 +0000 (09:16 -0800)]
Merge tag 'sound-4.4-rc4' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This time we've got a larger number of updates, mainly from ASoC
world. The only significant LOCs found here are for Realtek codecs,
where most of changes are quite systematic replacements.
There are also a few fixes in ASoC core side: one is the PM call order
fix to ensure the DPAM resume working properly. Another is the proper
cleanup call after freeing DAPM widgets, and the correction of the
wrong callback set in topology API.
The rest are a wide range of driver-specific small fixes, including
HD-audio"
* tag 'sound-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (35 commits)
ALSA: hda - Add Conexant CX8200 (14f1:2008) codec entry
ALSA: hda - Correct codec names for 14f1:50f1 and 14f1:50f3
ALSA: hda - Skip ELD notification during system suspend
ASoC: core: Change power state before rechecking endpoint
ASoC: fix kernel-doc warnings in sound/soc/soc-ops.c
ASoC: rt5645: Add dmi_system_id "Google Terra"
ASoC: rockchip: Fix incorrect VDW value for 24 bit
ASoC: fsl: clarify ac97 dependency
ASoC: Intel: Skylake: fix memory leak
ASoC: davinci-mcasp: Fix master capture only mode
ASoC: es8328: Fix shifts for mixer switches
ASoC: rt5645: Add dmi_system_id "Google Wizpig"
ASoC: sti: set player private data
ASoC: sti: rename ST proprietary DT properties
ASoC: sti: remove wrong error message
ASoC: Intel: Skylake: Add I2C depends for SKL machine
ASoC: topology: fix info callback for TLV byte control
ASoC: rt5670: fix wrong bit def for pll src
ASoC: nau8825: add pm function
ASoC: rt5645: Add struct dmi_system_id "Google Edgar" for Chrome OS
...
Linus Torvalds [Fri, 4 Dec 2015 16:59:10 +0000 (08:59 -0800)]
Merge tag 'pm+acpi-4.4-rc4' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI PCI host bridge
initialization code, clean up some recent changes (generic power
domains framework, ACPI AML debugger support), fix three older but
annoying bugs (PCI power management. generic power domains framework,
cpufreq) and a build problem (device properties framework), and update
a stale MAINTAINERS entry (ACPI backlight driver).
Specifics:
- Fix a regression in the ACPI PCI host bridge initialization code
introduced by the recent consolidation of the host bridge handling
on x86 and ia64 that forgot to take one special piece of code
related to NUMA on x86 into account (Liu Jiang).
- Improve the Kconfig help description of the new ACPI AML debugger
support option to avoid possible confusion (Peter Zijlstra).
- Remove a piece of code in the generic power domains framework that
should have been removed by one of the recent commits modifying
that code (Ulf Hansson).
- Reduce the log level of a PCI PM message that generates a lot of
false-positive log noise for some drivers and improve the message
itself while at it (Imre Deak).
- Fix the OF-based domain lookup code in the generic power domains
framework to make it drop references to DT nodes correctly (Eric
Anholt).
- Prevent the cpufreq core from setting the policy back to the
default after a CPU offline/online cycle for cpufreq drivers
providing the ->setpolicy callback (Srinivas Pandruvada).
- Fix a build problem for CONFIG_ACPI unset in the device properties
framework (Hanjun Guo).
- Fix a stale file path in the ACPI backlight driver entry in
MAINTAINERS (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
cpufreq: use last policy after online for drivers with ->setpolicy
PCI / PM: Tune down retryable runtime suspend error messages
PM / Domains: Validate cases of a non-bound driver in genpd governor
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
x86/PCI/ACPI: Fix regression caused by commit
4d6b4e69a245
ACPI: Better describe ACPI_DEBUGGER
Ard Biesheuvel [Thu, 3 Dec 2015 08:25:22 +0000 (09:25 +0100)]
ARM/arm64: KVM: correct PTE uncachedness check
Commit
e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's
uncachedness") modified the logic to test whether a HYP or stage-2
mapping needs flushing, from [incorrectly] interpreting the page table
attributes to [incorrectly] checking whether the PFN that backs the
mapping is covered by host system RAM. The PFN number is part of the
output of the translation, not the input, so we have to use pte_pfn()
on the contents of the PTE, not __phys_to_pfn() on the HYP virtual
address or stage-2 intermediate physical address.
Fixes:
e6fab5442345 ("ARM/arm64: KVM: test properly for a PTE's uncachedness")
Cc: stable@vger.kernel.org
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:14 +0000 (15:03 +0300)]
arm64: KVM: Get rid of old vcpu_reg()
Using oldstyle vcpu_reg() accessor is proven to be inappropriate and
unsafe on ARM64. This patch converts the rest of use cases to new
accessors and completely removes vcpu_reg() on ARM64.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:13 +0000 (15:03 +0300)]
arm64: KVM: Correctly handle zero register in system register accesses
System register accesses also use zero register for Rt == 31, and
therefore using it will also result in getting SP value instead. This
patch makes them also using new accessors, introduced by the previous
patch. Since register value is no longer directly associated with storage
inside vCPU context structure, we introduce a dedicated storage for it in
struct sys_reg_params.
This refactor also gets rid of "massive hack" in kvm_handle_cp_64().
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:12 +0000 (15:03 +0300)]
arm64: KVM: Remove const from struct sys_reg_params
Further rework is going to introduce a dedicated storage for transfer
register value in struct sys_reg_params. Before doing this we have to
remove 'const' modifiers from it in all accessor functions and their
callers.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Pavel Fedin [Fri, 4 Dec 2015 12:03:11 +0000 (15:03 +0300)]
arm64: KVM: Correctly handle zero register during MMIO
On ARM64 register index of 31 corresponds to both zero register and SP.
However, all memory access instructions, use ZR as transfer register. SP
is used only as a base register in indirect memory addressing, or by
register-register arithmetics, which cannot be trapped here.
Correct emulation is achieved by introducing new register accessor
functions, which can do special handling for reg_num == 31. These new
accessors intentionally do not rely on old vcpu_reg() on ARM64, because
it is to be removed. Since the affected code is shared by both ARM
flavours, implementations of these accessors are also added to ARM32 code.
This patch fixes setting MMIO register to a random value (actually SP)
instead of zero by something like:
*((volatile int *)reg) = 0;
compilers tend to generate "str wzr, [xx]" here
[Marc: Fixed 32bit splat]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Ilya Dryomov [Fri, 27 Nov 2015 18:23:24 +0000 (19:23 +0100)]
rbd: don't put snap_context twice in rbd_queue_workfn()
Commit
4e752f0ab0e8 ("rbd: access snapshot context and mapping size
safely") moved ceph_get_snap_context() out of rbd_img_request_create()
and into rbd_queue_workfn(), adding a ceph_put_snap_context() to the
error path in rbd_queue_workfn(). However, rbd_img_request_create()
consumes a ref on snapc, so calling ceph_put_snap_context() after
a successful rbd_img_request_create() leads to an extra put. Fix it.
Cc: stable@vger.kernel.org # 3.18+
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josh Durgin <jdurgin@redhat.com>
Rafael J. Wysocki [Fri, 4 Dec 2015 13:01:42 +0000 (14:01 +0100)]
Merge branches 'pm-domains' and 'pm-cpufreq'
* pm-domains:
PM / Domains: Fix bad of_node_put() in failure paths of genpd_dev_pm_attach()
PM / Domains: Validate cases of a non-bound driver in genpd governor
* pm-cpufreq:
cpufreq: use last policy after online for drivers with ->setpolicy
Rafael J. Wysocki [Fri, 4 Dec 2015 13:01:17 +0000 (14:01 +0100)]
Merge branches 'acpica', 'acpi-video' and 'device-properties'
* acpica:
ACPI: Better describe ACPI_DEBUGGER
* acpi-video:
MAINTAINERS: ACPI / video: update a file name in drivers/acpi/
* device-properties:
ACPI / property: fix compile error for acpi_node_get_property_reference() when CONFIG_ACPI=n
Rafael J. Wysocki [Fri, 4 Dec 2015 13:01:02 +0000 (14:01 +0100)]
Merge branches 'acpi-pci' and 'pm-pci'
* acpi-pci:
x86/PCI/ACPI: Fix regression caused by commit
4d6b4e69a245
* pm-pci:
PCI / PM: Tune down retryable runtime suspend error messages
Peter Zijlstra [Wed, 7 Oct 2015 12:14:13 +0000 (14:14 +0200)]
sched/core: Fix an SMP ordering race in try_to_wake_up() vs. schedule()
Oleg noticed that its possible to falsely observe p->on_cpu == 0 such
that we'll prematurely continue with the wakeup and effectively run p on
two CPUs at the same time.
Even though the overlap is very limited; the task is in the middle of
being scheduled out; it could still result in corruption of the
scheduler data structures.
CPU0 CPU1
set_current_state(...)
<preempt_schedule>
context_switch(X, Y)
prepare_lock_switch(Y)
Y->on_cpu = 1;
finish_lock_switch(X)
store_release(X->on_cpu, 0);
try_to_wake_up(X)
LOCK(p->pi_lock);
t = X->on_cpu; // 0
context_switch(Y, X)
prepare_lock_switch(X)
X->on_cpu = 1;
finish_lock_switch(Y)
store_release(Y->on_cpu, 0);
</preempt_schedule>
schedule();
deactivate_task(X);
X->on_rq = 0;
if (X->on_rq) // false
if (t) while (X->on_cpu)
cpu_relax();
context_switch(X, ..)
finish_lock_switch(X)
store_release(X->on_cpu, 0);
Avoid the load of X->on_cpu being hoisted over the X->on_rq load.
Reported-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 6 Oct 2015 12:36:17 +0000 (14:36 +0200)]
sched/core: Better document the try_to_wake_up() barriers
Explain how the control dependency and smp_rmb() end up providing
ACQUIRE semantics and pair with smp_store_release() in
finish_lock_switch().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Hiroshi Shimamoto [Thu, 19 Nov 2015 15:47:28 +0000 (16:47 +0100)]
sched/cputime: Fix invalid gtime in proc
/proc/stats shows invalid gtime when the thread is running in guest.
When vtime accounting is not enabled, we cannot get a valid delta.
The delta is calculated with now - tsk->vtime_snap, but tsk->vtime_snap
is only updated when vtime accounting is runtime enabled.
This patch makes task_gtime() just return gtime without computing the
buggy non-existing tickless delta when vtime accounting is not enabled.
Use context_tracking_is_enabled() to check if vtime is accounting on
some cpu, in which case only we need to check the tickless delta. This
way we fix the gtime value regression on machines not running nohz full.
The kernel config contains CONFIG_VIRT_CPU_ACCOUNTING_GEN=y and
CONFIG_NO_HZ_FULL_ALL=n and boot without nohz_full.
I ran and stop a busy loop in VM and see the gtime in host.
Dump the 43rd field which shows the gtime in every second:
# while :; do awk '{print $3" "$43}' /proc/3955/task/4014/stat; sleep 1; done
S 4348
R 7064566
R 7064766
R 7064967
R 7065168
S 4759
S 4759
During running busy loop, it returns large value.
After applying this patch, we can see right gtime.
# while :; do awk '{print $3" "$43}' /proc/10913/task/10956/stat; sleep 1; done
S 5338
R 5365
R 5465
R 5566
R 5666
S 5726
S 5726
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1447948054-28668-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Xunlei Pang [Wed, 2 Dec 2015 11:52:59 +0000 (19:52 +0800)]
sched/core: Clear the root_domain cpumasks in init_rootdomain()
root_domain::rto_mask allocated through alloc_cpumask_var()
contains garbage data, this may cause problems. For instance,
When doing pull_rt_task(), it may do useless iterations if
rto_mask retains some extra garbage bits. Worse still, this
violates the isolated domain rule for clustered scheduling
using cpuset, because the tasks(with all the cpus allowed)
belongs to one root domain can be pulled away into another
root domain.
The patch cleans the garbage by using zalloc_cpumask_var()
instead of alloc_cpumask_var() for root_domain::rto_mask
allocation, thereby addressing the issues.
Do the same thing for root_domain's other cpumask memembers:
dlo_mask, span, and online.
Signed-off-by: Xunlei Pang <xlpang@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1449057179-29321-1-git-send-email-xlpang@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Sasha Levin [Tue, 1 Dec 2015 01:34:20 +0000 (20:34 -0500)]
sched/core: Remove false-positive warning from wake_up_process()
Because wakeups can (fundamentally) be late, a task might not be in
the expected state. Therefore testing against a task's state is racy,
and can yield false positives.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: oleg@redhat.com
Fixes:
9067ac85d533 ("wake_up_process() should be never used to wakeup a TASK_STOPPED/TRACED task")
Link: http://lkml.kernel.org/r/1448933660-23082-1-git-send-email-sasha.levin@oracle.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Peter Zijlstra [Tue, 1 Dec 2015 13:04:04 +0000 (14:04 +0100)]
sched/wait: Fix signal handling in bit wait helpers
Vladimir reported getting RCU stall warnings and bisected it back to
commit:
743162013d40 ("sched: Remove proliferation of wait_on_bit() action functions")
That commit inadvertently reversed the calls to schedule() and signal_pending(),
thereby not handling the case where the signal receives while we sleep.
Reported-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mark.rutland@arm.com
Cc: neilb@suse.de
Cc: oleg@redhat.com
Fixes:
743162013d40 ("sched: Remove proliferation of wait_on_bit() action functions")
Fixes:
cbbce8220949 ("SCHED: add some "wait..on_bit...timeout()" interfaces.")
Link: http://lkml.kernel.org/r/20151201130404.GL3816@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Kirill A. Shutemov [Mon, 30 Nov 2015 10:10:33 +0000 (11:10 +0100)]
x86/mm: Fix regression with huge pages on PAE
Recent PAT patchset has caused issue on 32-bit PAE machines:
page:
eea45000 count:0 mapcount:-128 mapping: (null) index:0x0 flags: 0x40000000()
page dumped because: VM_BUG_ON_PAGE(page_mapcount(page) < 0)
------------[ cut here ]------------
kernel BUG at /home/build/linux-boris/mm/huge_memory.c:1485!
invalid opcode: 0000 [#1] SMP
[...]
Call Trace:
unmap_single_vma
? __wake_up
unmap_vmas
unmap_region
do_munmap
vm_munmap
SyS_munmap
do_fast_syscall_32
? __do_page_fault
sysenter_past_esp
Code: ...
EIP: [<
c11bde80>] zap_huge_pmd+0x240/0x260 SS:ESP 0068:
f6459d98
The problem is in pmd_pfn_mask() and pmd_flags_mask(). These
helpers use PMD_PAGE_MASK to calculate resulting mask.
PMD_PAGE_MASK is 'unsigned long', not 'unsigned long long' as
phys_addr_t is on 32-bit PAE (ARCH_PHYS_ADDR_T_64BIT). As a
result, the upper bits of resulting mask get truncated.
pud_pfn_mask() and pud_flags_mask() aren't problematic since we
don't have PUD page table level on 32-bit systems, but it's
reasonable to keep them consistent with PMD counterpart.
Introduce PHYSICAL_PMD_PAGE_MASK and PHYSICAL_PUD_PAGE_MASK in
addition to existing PHYSICAL_PAGE_MASK and reworks helpers to
use them.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
[ Fix -Woverflow warnings from the realmode code. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Toshi Kani <toshi.kani@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jürgen Gross <jgross@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: elliott@hpe.com
Cc: konrad.wilk@oracle.com
Cc: linux-mm <linux-mm@kvack.org>
Fixes:
f70abb0fc3da ("x86/asm: Fix pud/pmd interfaces to handle large PAT bit")
Link: http://lkml.kernel.org/r/1448878233-11390-2-git-send-email-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Jani Nikula [Thu, 3 Dec 2015 12:00:03 +0000 (14:00 +0200)]
drm: keep connector status change logging human readable
We've had human readable connector status change debug logging since
commit
ed7951dc13aad4a14695ec8122e9f0e2ef25d39e
Author: Lespiau, Damien <damien.lespiau@intel.com>
Date: Fri May 10 12:36:42 2013 +0000
drm: Make the HPD status updates debug logs more readable
but
commit
162b6a57ac50eec236530a16c071ffa50e87362a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Jan 21 08:45:21 2015 +0100
drm/probe-helper: don't lose hotplug event
added a new one with just the numbers. Fix it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449144003-2877-1-git-send-email-jani.nikula@intel.com
Daniel Vetter [Tue, 10 Nov 2015 16:37:31 +0000 (17:37 +0100)]
drm/nouveau: Fix pre-nv50 pageflip events (v4)
Apparently pre-nv50 pageflip events happen before the actual vblank
period. Therefore that functionality got semi-disabled in
commit
af4870e406126b7ac0ae7c7ce5751f25ebe60f28
Author: Mario Kleiner <mario.kleiner.de@gmail.com>
Date: Tue May 13 00:42:08 2014 +0200
drm/nouveau/kms/nv04-nv40: fix pageflip events via special case.
Unfortunately that hack got uprooted in
commit
cc1ef118fc099295ae6aabbacc8af94d8d8885eb
Author: Thierry Reding <treding@nvidia.com>
Date: Wed Aug 12 17:00:31 2015 +0200
drm/irq: Make pipe unsigned and name consistent
Triggering a warning when trying to sample the vblank timestamp for a
non-existing pipe. There's a few ways to fix this:
- Open-code the old behaviour, which just enshrines this slight
breakage of the userspace ABI.
- Revert Mario's commit and again inflict broken timestamps, again not
pretty.
- Fix this for real by delaying the pageflip TS until the next vblank
interrupt, thereby making it accurate.
This patch implements the third option. Since having a page flip
interrupt that happens when the pageflip gets armed and not when it
completes in the next vblank seems to be fairly common (older i915 hw
works very similarly) create a new helper to arm vblank events for
such drivers.
v2 (Mario Kleiner):
- Fix function prototypes in drmP.h
- Add missing vblank_put() for pageflip completion without
pageflip event.
- Initialize sequence number for queued pageflip event to avoid
trouble in drm_handle_vblank_events().
- Remove dead code and spelling fix.
v3 (Mario Kleiner):
- Add a signed-off-by and cc stable tag per Ilja's advice.
v4 (Thierry Reding):
- Fix kerneldoc typo, discovered by Michel Dänzer
- Rearrange tags and changelog
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=106431
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mario Kleiner <mario.kleiner.de@gmail.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Cc: stable@vger.kernel.org # v4.3
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Thomas Hellstrom [Wed, 2 Dec 2015 17:24:46 +0000 (09:24 -0800)]
drm: Fix an unwanted master inheritance v2
A client calling drmSetMaster() using a file descriptor that was opened
when another client was master would inherit the latter client's master
object and all its authenticated clients.
This is unwanted behaviour, and when this happens, instead allocate a
brand new master object for the client calling drmSetMaster().
Fixes a BUG() throw in vmw_master_set().
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Dave Airlie [Fri, 4 Dec 2015 02:26:29 +0000 (12:26 +1000)]
Merge tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux into drm-fixes
imx-drm crtc, plane, parallel panel, and TV encoder fixes
- Use drm_crtc_send_vblank_event to fix per crtc vblank handling
- Move the crtc device of_node assignment out of the ipuv3-crtc driver into
ipu-common code, where the devices are created.
- Fix parallel display support with simple-panels
- Remove some unused fields and superfluous checks
- Switch to universal planes and add error handling for primary plane creation
- Fix module autoload for TV encoder driver
* tag 'imx-drm-fixes-2015-12-01' of git://git.pengutronix.de/git/pza/linux:
drm: imx: imx-tve: Fix module autoload for OF platform driver
drm: imx: convert to drm_crtc_send_vblank_event()
GPU-DRM-IMX: Delete an unnecessary check before drm_fbdev_cma_restore_mode()
drm/imx: Remove of_node assignment from ipuv3-crtc driver probe
gpu: ipu-v3: Assign of_node of child platform devices to corresponding ports
gpu: ipu-v3: Remove reg_offset field
gpu: ipu-v3: drop unused dmfc field from client platform data
drm/imx: parallel-display: allow to determine bus format from the connected panel
drm/imx: ipuv3-crtc: Return error if ipu_plane_init() fails for primary plane
drm/imx: switch to universal planes
Dave Airlie [Fri, 4 Dec 2015 02:23:13 +0000 (12:23 +1000)]
Merge tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel into drm-fixes
Another batch of drm/i915 fixes for v4.4, on top of the ones from
earlier this week. One timeout handling regression fix from Chris, and
backport of five patches from our -next to fix a power management
related HDMI hotplug regression.
* tag 'drm-intel-fixes-2015-12-03' of git://anongit.freedesktop.org/drm-intel:
drm/i915: take a power domain reference while checking the HDMI live status
drm/i915: add MISSING_CASE to a few port/aux power domain helpers
drm/i915/ddi: fix intel_display_port_aux_power_domain() after HDMI detect
drm/i915: Introduce a gmbus power domain
drm/i915: Clean up AUX power domain handling
drm/i915: Check the timeout passed to i915_wait_request