drm/i915: Don't increase the GPU frequency from the delayed VLV rps timer

There's little point in increasing the GPU frequency from the delayed
rps work on VLV. Now when the GPU is idle, the GPU frequency actually
keeps dropping gradually until it hits the minimum, whereas previously
it just ping-ponged constantly between RPe and RPe-1.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: GEN6_RP_INTERRUPT_LIMITS doesn't seem to exist on VLV

I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs.
Reading it always returns zero from what I can tell, and eliminating
it doesn't seem to make any difference to the behaviour of the system.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Make the rps new_delay comparison more readable

Eliminate the weird inverted logic from the rps new_delay comparison.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Don't wait for Punit after each freq change on VLV

It seems that even though Punit reports the frequency change to have
been completed, it still reports the old frequency in the status
register for some time.

So rather than polling for Punit to complete the frequency change after
each request, poll before. This gets rid of the spurious "Punit overrode
GPU freq" messages.

This also lets us continue working while Punit is performing the actual
frequency change. As a result, openarena demo088-test1 timedemo average
fps is increased by ~5 fps, and the slowest frame duration is reduced
by ~25%.

The sysfs cur_freq file always reads the current frequency from Punit
anyway, so having rps.cur_delay be slightly off at times doesn't matter.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Clean up VLV rps code a bit

Always print both the MHz value and raw register value for rps stuff.

Also kill a somewhat pointless local 'rpe' variable and just use
dev_priv->rps.rpe_delay.

While at it clean up the caps in "GPU" and "Punit" debug messages.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Detect invalid scanout pitches

Report back the user error of attempting to setup a CRTC with an invalid
framebuffer pitch. This is trickier than it should be as on gen4, there
is a restriction that tiled surfaces must have a stride less than 16k -
which is less than the largest supported CRTC size.

v2: Fix the limits for gen3
v3: Move check into intel_framebuffer_init() and fix VLV limits. (vsyrjala)
v4: Use idiomatic '>=' for generation checks

References: https://bugs.freedesktop.org/show_bug.cgi?id=65099
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Remove duplicated WaForceL3Serialization:vlv

No need to apply WaForceL3Serialization:vlv twice.

Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: don't scream into dmesg when a modeset fails

There are legit cases, e.g. when userspace asks for something
impossible. So tune it down to debug output like we do with all other
userspace-triggerable warnings.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66111#c5
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix up sdvo hpd pins for i965g/gm

Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.

v2: Update comment a bit.

Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Introduce an HAS_IPS() macro

Follow the trend and don't code conditions with platforms but with
features.

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix build warning on format specifier mismatch

drivers/gpu/drm/i915/i915_gem.c: In function ‘i915_gem_object_bind_to_gtt’:
drivers/gpu/drm/i915/i915_gem.c:3002:3: warning: format ‘%ld’ expects
argument of type ‘long int’, but argument 5 has type ‘size_t’ [-Wformat]

v2: Use %zu instead of %d. Two char patch, and 100% wrong. (Ville)

Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: tune down DIDL warning about too many outputs

Nothing the user (nor we) really can do about this, but upsets a nice
quiet boot.

Note that this happens mostly on SDVs where OEMs obviously haven't had
a chance yet to appropriately trim the output list.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65988
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Amend commit message a bit to clarify a question from Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: make compact dma scatter lists creation work with SWIOTLB backend.

Git commit 90797e6d1ec0dfde6ba62a48b9ee3803887d6ed4
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.

On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:

[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28

Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).

That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).

Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.

This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.

An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.

Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: Fix PCH detect with multiple ISA bridges in VM

In some virtualized environments (e.g. XEN), there is irrelevant ISA bridge in
the system. To work reliably, we should scan trhough all the ISA bridge
devices and check for the first match, instead of only checking the first one.

Signed-off-by: Rui Guo <firemeteor@users.sourceforge.net>
[danvet: Fixup conflict with the num_pch_pll removal. And add
subsystem header to the commit message headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: rename intel_dp_destroy to intel_dp_connector_destroy

Because it's the function that destroys the connector, not the
encoder. And we already have intel_dp_encoder_destroy.

This has annoyed me for a long time.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: check the return value of intel_dp_i2c_init

We've been ignoring this return value, so print a nice backtrace in
case it's not what we expected.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix the "ghost eDP" encoder unwind path

Because calling intel_dp_encoder_destroy inside
intel_edp_init_connector is just wrong. This is the initialization
path, so we should properly unwind all the initialization through the
whole caller stack.

On the intel_dp_encoder_destroy function we do the following:
1 - Call i2c_del_adapter
2 - Call drm_encoder_cleanup
3 - If edp:
3.1 - Cancel panel_vdd_work
3.2 - Call ironlake_panel_vdd_of_sync
4 - Free the encoder

And here is how we unwind each specific step:
1 - We have intel_dp_init_connector -> intel_dp_i2c_init ->
    i2c_dp_aux_add_bus -> i2c_add_adapter, so we call
    i2c_del_dapter at intel_dp_init_connector
2 - Call it in the same function that called drm_encoder_init
3 - Call it in the same function that called INIT_DELAYED_WORK
4 - Free it in the same function that allocated it

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: fix the "ghost eDP" connector unwind path

Because calling intel_dp_destroy inside intel_edp_init_connector is
just wrong. This is the initialization path, so we should properly
unwind all the initialization through the whole caller stack.

On the intel_dp_destroy function we do the following:
1 - Free edid if it exists
2 - Call intel_panel_fini in case it's eDP
3 - Call drm_sysfs_connector_remove
4 - Call drm_connector_cleanup
5 - Free the connector

And here is how we unwind each specific step:
1 - No need as we still didn't assign anything
2 - No need as we still didn't call intel_panel_init
3 - Call it in the same function that called drm_sysfs_connector_add
4 - Call it in the same function that called drm_connector_init
5 - Free it in the same function that allocated it

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: propagate errors from intel_dp_init_connector

In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:

commit 21a8e6a4853b2ed39fa4c5188a710f2cf1b92026
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Apr 10 23:28:35 2013 +0200
    drm/i915: don't setup hdmi for port D edp in ddi_init

So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: extract intel_edp_init_connector

Because intel_dp_init_connector is too big for my poor little brain.
No functional changes.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

drm/i915: don't check encoder at DP connector destroy()

By the time we call intel_dp_destroy (which destroys the connector)
the encoder may have been destroyed already, so if we use it we may be
reading some free memory. That happens in drm_mode_config_cleanup()
and also inside intel_dp_init_connector() when we detect a ghost eDP.

I also hope this may solve some random memory bugs.

Reported by kmemcheck.

Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>

Revert "drm: kms_helper: don't lose hotplug event"

This reverts commit 160954b7bca43da7cd3cfbce310e6df919a8216e.

This was rearming the workqueue with a 0 timeout, causing
a WARN_ON, and possible loop.

Daniel writes:
"I've looked a bit into this and I think we need to have a separate
work struct for recovering these lost hotplug events since the
continuous self-rearming case is a real risk (e.g. if a connector
flip-flops all the time). At least I don't see a sane way to block out
re-arming with the current code in a simple way. So reverting the
offender seems like the right thing and I'll go back to the drawing
board for 3.12."

Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/doc: Document the KMS property API

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/doc: Remove outdated note about i915 driver not behaving properly

The i915 driver has been fixed not to modify the mode argument of the
encoder mode_fixup operation. Remove the related comment from the
documentation.

Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm: Improve manual IRQ installation documentation

Define the rules for using irqs from drm drivers.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/prime: add return check for dma_buf_fd

The dma_buf_fd() can return error when it fails to prepare fd,
so the dma_buf needs to be put.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/prime: reorder drm_prime_add_buf_handle and remove prototype

Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/prime: fix to put an exported dma_buf for adding handle failure

When drm_prime_add_buf_handle() returns failure for an exported
dma_buf, the dma_buf was already allocated and its refcount was
increased, so it needs to be put.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/prime: support to cache mapping

The drm prime also can support it like GEM CMA supports to cache
mapping. It doesn't allow multiple mappings for one attachment.

[airlied: rebased on top of other prime changes]
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/prime: replace NULL with error value in drm_prime_pages_to_sg

Instead of NULL, error value is casted with ERR_PTR() for
drm_prime_pages_to_sg() and IS_ERR_OR_NULL() macro is replaced
with IS_ERR() macro for drm_gem_map_dma_buf().

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/prime: fix to check return of dma_map_sg in prime helper

The dma_map_sg(), in map_dma_buf callback operation of prime helper,
can return 0 when it fails to map, so it needs to release related
resources.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/gem: fix not to assign error value to gem name

If idr_alloc() is failed, obj->name can be error value. Also
it cleans up duplicated flink processing code.

This regression has been introduced in

commit 2e928815c1886fe628ed54623aa98d0889cf5509
Author: Tejun Heo <tj@kernel.org>
Date:   Wed Feb 27 17:04:08 2013 -0800

    drm: convert to idr_alloc()

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/gem: add mutex lock when using drm_gem_mmap_obj

The drm_gem_mmap_obj() has to be protected with dev->struct_mutex,
but some caller functions do not. So it adds mutex lock to missing
callers and adds assertion to check whether drm_gem_mmap_obj() is
called with mutex lock or not.

Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/omap: drop the !FB_OMAP2 dep

This ends up causing circularity and really let people shoot themselves
in the foot.

Acked-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: get rid of ttm_bo_is_reserved

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/vmwgfx: get rid of ttm_bo_is_reserved usage

Use lockdep_assert_held instead.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon: get rid of ttm_bo_is_reserved usage

Try to use lockdep_assert_held or other alternatives where possible.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: get rid of ttm_bo_is_reserved usage

Use lockdep_assert_held instead.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: inline ttm_bo_reserve and related calls

Makes lockdep a lot more useful.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon: inline reservations

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/mgag200: inline reservations

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/cirrus: inline reservations

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ast: inline reservations

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: convert to the reservation api

Now that the code is compatible in semantics, flip the switch.
Use ww_mutex instead of the homegrown implementation.

ww_mutex uses -EDEADLK to signal that the caller has to back off,
and -EALREADY to indicate this buffer is already held by the caller.

ttm used -EAGAIN and -EDEADLK for those, respectively. So some changes
were needed to handle this correctly.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: make flipping lockdep safe

cli->mutex was inverted with reservations, and multiple reservations were
used without a ticket, fix both. This commit had to be done after the previous
commit, because otherwise ttm_eu_* calls would use a different seqno counter..

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ttm: make ttm reservation calls behave like reservation calls

This commit converts the source of the val_seq counter to
the ww_mutex api. The reservation objects are converted later,
because there is still a lockdep splat in nouveau that has to
resolved first.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

reservation: cross-device reservation support, v4

This adds support for a generic reservations framework that can be
hooked up to ttm and dma-buf and allows easy sharing of reservations
across devices.

The idea is that a dma-buf and ttm object both will get a pointer
to a struct reservation_object, which has to be reserved before
anything is done with the contents of the dma-buf.

Changes since v1:
 - Fix locking issue in ticket_reserve, which could cause mutex_unlock
   to be called too many times.
Changes since v2:
 - All fence related calls and members have been taken out for now,
   what's left is the bare minimum to be useful for ttm locking conversion.
Changes since v3:
 - Removed helper functions too. The documentation has an example
   implementation for locking. With the move to ww_mutex there is no
   need to have much logic any more.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/ast: do not attempt to acquire a reservation while in an interrupt handler

Mutexes should not be acquired in interrupt context. While the trylock
fastpath is arguably safe on all implementations, the slowpath
unlock path definitely isn't.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/mgag200: do not attempt to acquire a reservation while in an interrupt handler

Mutexes should not be acquired in interrupt context. While the trylock
fastpath is arguably safe on all implementations, the slowpath
unlock path definitely isn't.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/cirrus: do not attempt to acquire a reservation while in an interrupt handler

Mutexes should not be acquired in interrupt context. While the trylock
fastpath is arguably safe on all implementations, the slowpath
unlock path definitely isn't. This fixes the following lockdep splat:

[   13.044313] ------------[ cut here ]------------
[   13.044367] WARNING: at /c/kernel-tests/src/tip/kernel/mutex.c:858 mutex_trylock+0x87/0x220()
[   13.044378] DEBUG_LOCKS_WARN_ON(in_interrupt())
[   13.044378] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.0-rc4-00296-ga2963dd #20
[   13.044379] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[   13.044390]  0000000000000009 ffff88000de039f8 ffffffff81fc86d5 ffff88000de03a38
[   13.044395]  ffffffff810d511b ffff880000000018 ffff88000f33c690 0000000000000001
[   13.044398]  00000000000003f0 ffff88000f4677c8 0000000000000000 ffff88000de03a98
[   13.044400] Call Trace:
[   13.044412]  <IRQ>  [<ffffffff81fc86d5>] dump_stack+0x19/0x1b
[   13.044441]  [<ffffffff810d511b>] warn_slowpath_common+0x6b/0x90
[   13.044445]  [<ffffffff810d51a6>] warn_slowpath_fmt+0x46/0x50
[   13.044448]  [<ffffffff81fd34d7>] mutex_trylock+0x87/0x220
[   13.044482]  [<ffffffff8186484d>] cirrus_dirty_update+0x1cd/0x330
[   13.044486]  [<ffffffff818649e8>] cirrus_imageblit+0x38/0x50
[   13.044506]  [<ffffffff8165782e>] soft_cursor+0x22e/0x240
[   13.044510]  [<ffffffff81656c31>] bit_cursor+0x581/0x5b0
[   13.044525]  [<ffffffff815de9f4>] ? vsnprintf+0x124/0x670
[   13.044529]  [<ffffffff81651333>] ? get_color.isra.16+0x43/0x130
[   13.044532]  [<ffffffff81653fca>] fbcon_cursor+0x18a/0x1d0
[   13.044535]  [<ffffffff816566b0>] ? update_attr.isra.2+0xa0/0xa0
[   13.044556]  [<ffffffff81754b82>] hide_cursor+0x32/0xa0
[   13.044565]  [<ffffffff81755bd3>] vt_console_print+0x103/0x3b0
[   13.044569]  [<ffffffff810d58ac>] ? print_time+0x9c/0xb0
[   13.044576]  [<ffffffff810d5960>] ? print_prefix+0xa0/0xc0
[   13.044580]  [<ffffffff810d63f6>] call_console_drivers.constprop.6+0x146/0x1f0
[   13.044593]  [<ffffffff815f9b38>] ? do_raw_spin_unlock+0xc8/0x100
[   13.044597]  [<ffffffff810d6f27>] console_unlock+0x2f7/0x460
[   13.044600]  [<ffffffff810d787a>] vprintk_emit+0x59a/0x5e0
[   13.044615]  [<ffffffff81fb676c>] printk+0x4d/0x4f
[   13.044650]  [<ffffffff82ba5511>] print_local_APIC+0x28/0x41c
[   13.044672]  [<ffffffff8114db55>] generic_smp_call_function_single_interrupt+0x145/0x2b0
[   13.044688]  [<ffffffff8106f9e7>] smp_call_function_single_interrupt+0x27/0x40
[   13.044697]  [<ffffffff81fd8f72>] call_function_single_interrupt+0x72/0x80
[   13.044707]  <EOI>  [<ffffffff81078166>] ? native_safe_halt+0x6/0x10
[   13.044717]  [<ffffffff811425cd>] ? trace_hardirqs_on+0xd/0x10
[   13.044738]  [<ffffffff8104f669>] default_idle+0x59/0x120
[   13.044742]  [<ffffffff810501e8>] arch_cpu_idle+0x18/0x40
[   13.044754]  [<ffffffff811320c5>] cpu_startup_entry+0x235/0x410
[   13.044763]  [<ffffffff81f9e781>] rest_init+0xd1/0xe0
[   13.044766]  [<ffffffff81f9e6b5>] ? rest_init+0x5/0xe0
[   13.044778]  [<ffffffff82b93ec2>] start_kernel+0x425/0x493
[   13.044781]  [<ffffffff82b93810>] ? repair_env_string+0x5e/0x5e
[   13.044786]  [<ffffffff82b93595>] x86_64_start_reservations+0x2a/0x2c
[   13.044789]  [<ffffffff82b93688>] x86_64_start_kernel+0xf1/0x100
[   13.044799] ---[ end trace 113ad28772af4058 ]---

Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: always select ACPI_VIDEO if ACPI is enabled.

Having nouveau builtin would still allow ACPI_VIDEO to be used as external module
if some of the deps for acpi_video have not been met, which would result in a linking
failure. Solve this by selecting all dependencies as well.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: complain loudly if buffer is pinned during destruction

Shouldn't happen, and we invert the struct_mutex with reservation here,
potentially leading to deadlocks. Once reservations become lockdep annotated,
lockdep will go splat on this.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: fixup fbcon failure paths

Add missing calls, and fix a leak from forgetting to call the unpin function.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: unpin notify object in chan_fini

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/nouveau: implement prime helper unpin function

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

drm/radeon: implement unpin function, v2

Changes since v1:
- Fixup compiler warning in unpin function.

Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge branch 'drm-next-3.11' of git://people.freedesktop.org/~agd5f/linux into drm-next

This is the pull request for radeon for 3.11.  Highlights include:

- Support for CIK (Sea Islands) asics: 3D, compute, UVD
- DPM (Dynamic Power Management) support for 6xx-SI
- ASPM support for 6xx-SI
- Assorted bug fixes

* 'drm-next-3.11' of git://people.freedesktop.org/~agd5f/linux: (168 commits)
  drm/radeon/SI: fix TDP adjustment in set_power_state
  drm/radeon/NI: fix TDP adjustment in set_power_state
  drm/radeon: fix endian issues in atombios dpm code
  drm/radeon/dpm: fix UVD clock setting on SI
  drm/radeon/dpm: fix UVD clock setting on cayman
  drm/radeon/dpm: add support for setting UVD clock on rv6xx
  drm/radeon/dpm: add support for setting UVD clock on rs780
  drm/radeon: fix typo in ni_print_power_state
  drm/radeon: fix typo in cik_select_se_sh()
  drm/radeon/si: fix typo in function name
  drm/radeon/dpm: fix typo in setting uvd clock
  drm/radeon/dpm: add dpm_set_power_state failure output (si)
  add dpm_set_power_state failure output (7xx-ni)
  drm/radeon/dpm: add dpm_set_power_state failure output (7xx-ni)
  drm/radeon/dpm: add dpm_enable failure output (si)
  drm/radeon/dpm: add dpm_enable failure output (7xx-ni)
  drm/radeon/kms: add dpm support for SI (v7)
  drm/radeon: switch SI to use radeon_ucode.h
  drm/radeon: add SI to r600_is_internal_thermal_sensor()
  drm/radeon/dpm/rs780: properly catch errors in dpm setup
  ...

Merge tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel into drm-next

Last 3.11 feature pull. I have a few odds bits and pieces and fixes in my
queue, I'll sort them out later on to see what's for 3.11-fixes and what's
for 3.12. But nothing to hold this here up imo.

Highlights:
- more hangcheck work from Mika and Chris to prepare for arb robustness
- trickle feed fixes from Ville
- first parts of the shared pch pll rework, with some basic hw state
  readout and cross-checking (this shuts up the confused pch pll refcount
  WARN that Linus just recently forwarded)
- Haswell audio power well support from Wang Xingchao (alsa bits acked by
  Takashi)
- some cleanups and asserts sprinkling around the plane/gamma enabling
  sequence from Ville
- more gtt refactoring from Ben
- clear up the adjusted->mode vs. pixel clock vs. port clock confusion
- 30bpp support, this time for real hopefully

* tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
  drm/i915: remove a superflous semi-colon
  drm/i915: Kill useless "Enable panel fitter" comments
  drm/i915: Remove extra "ring" from error message
  drm/i915: simplify the reduced clock handling for pch plls
  drm/i915: stop killing pfit on i9xx
  drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
  drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
  drm/i915: set up PIPECONF explicitly on ilk-ivb
  drm/i915: find guilty batch buffer on ring resets
  drm/i915: store ring hangcheck action
  drm/i915: add batch bo to i915_add_request()
  drm/i915: change i915_add_request to macro
  drm/i915: add i915_gem_context_get_hang_stats()
  drm/i915: add struct i915_ctx_hang_stats
  drm/i915: Try harder to disable trickle feed on VLV
  drm/i915: fix up pch pll enabling for pixel multipliers
  drm/i915: hw state readout and cross-checking for shared dplls
  drm/i915: WARN on lack of shared dpll
  drm/i915: split up intel_modeset_check_state
  drm/i915: extract readout_hw_state from setup_hw_state
  ...

Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_fb.c
drivers/gpu/drm/i915/intel_sdvo.c

drm/radeon/SI: fix TDP adjustment in set_power_state

Fixes hangs with DPM in some cases.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/NI: fix TDP adjustment in set_power_state

Fixes hangs with DPM in some cases.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: fix endian issues in atombios dpm code

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: fix UVD clock setting on SI

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: fix UVD clock setting on cayman

The rv770 version was using the wrong power state type.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add support for setting UVD clock on rv6xx

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add support for setting UVD clock on rs780

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: fix typo in ni_print_power_state

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: fix typo in cik_select_se_sh()

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/si: fix typo in function name

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: fix typo in setting uvd clock

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add dpm_set_power_state failure output (si)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

add dpm_set_power_state failure output (7xx-ni)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add dpm_set_power_state failure output (7xx-ni)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add dpm_enable failure output (si)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add dpm_enable failure output (7xx-ni)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/kms: add dpm support for SI (v7)

This adds dpm support for SI asics.  This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling

Set radeon.dpm=1 to enable.

v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Merge branch 'drm/for-next' of git://anongit.freedesktop.org/tegra/linux into drm-next

These changes are mostly minor fixes to things introduced in 3.10. The
biggest chunk is updates to the host1x firewall which checks job
submissions from userspace and wasn't working properly. All other
patches are mostly one-liners. Nothing new or too exciting this time
around.

* 'drm/for-next' of git://anongit.freedesktop.org/tegra/linux:
  gpu: host1x: Rework CPU syncpoint increment
  gpu: host1x: Fix client_managed type
  gpu: host1x: Fix memory access in syncpt request
  gpu: host1x: Copy gathers before verification
  gpu: host1x: Don't reset firewall between gathers
  gpu: host1x: Check reloc table before usage
  gpu: host1x: Check INCR opcode correctly
  drm/tegra: Remove DRIVER_BUS_PLATFORM from driver_features
  drm/tegra: Fix return value
  drm/tegra: Include header drm/drm.h
  MAINTAINERS: Update Tegra DRM entry
  drm/tegra: fix error return code in gr2d_submit()
  drm/tegra: fix missing unlock on error
  drm/tegra: Honor pixel-format changes
  drm/tegra: Explicitly set irq_enabled
  drm/tegra: Don't disable unused planes

drm/radeon: switch SI to use radeon_ucode.h

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: add SI to r600_is_internal_thermal_sensor()

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/rs780: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/r6xx: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/r7xx: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/trinity: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/sumo: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/evergreen: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/btc: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/ni: properly catch errors in dpm setup

We weren't properly catching errors in dpm_enable()
and dpm_set_power_state().

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/atom: fix voltage table parsing

The arrays items are variable sized.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: fix typo in atom voltage table handling (si+)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: fix typo in atom voltage table handling (6xx-ni)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: add pcie gen helper function

Add a helper function to determine the preferred
pcie gen based on the card, system, and circumstance.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: update radeon_atombios_get_default_voltages for mvdd

Add a way to look up the bootup mvdd.  Required for DPM on SI.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: validate voltages against dispclk requirements

Validate the voltages against the voltage requirements of the
dispclk.  We currently don't adjust the disp clock so it never
changes, but we need to filter out voltage levels that are too
low none the less.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: fix some memory leaks in extended table parsing

Forgot to free some structs when allocation fails for some
tables.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm/cayman: use new fixed point functions (v2)

Use the new fixed point functions for leakage
calculations on cayman.

v2: fix up 64 bit math

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm: add some additional fixed point helpers (v3)

Required for certain driver calculations.  Code
was written by Christian König and ported to the
drm by me.

v2: fix 64 bit divides
v3: fix 64 bit for real (math64.h)

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon: minor sid.h cleanup

Consolidate the non-register defines.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: save some display parameters for DPM

Required for SI.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: pull in ppm info from atom

Used by SI dpm.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: endian fixes for extended power tables

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

drm/radeon/dpm: pull in phase shedding limits from atom

Required for dpm on SI.

Signed-off-by: Alex Deucher <alexander.deucher@amd.com>