Arnd Bergmann [Mon, 16 Aug 2021 21:09:45 +0000 (23:09 +0200)]
Merge tag 'imx-dt64-5.15' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree changes for 5.15:
- New board support: Nitrogen8 SoM and MNT Reform2, LS1088A based
Traverse Ten64, i.MX8M based GW7902.
- A series from Ioana Ciornei to update PHY IRQ configuration for
LayerScape SoCs.
- A series from Tim Harvey to update Gateworks imx8mm-venice devices.
- Replace deprecated `fsl,usbphy` property with phys phandle.
- Add MIPI CSI phy and bridge descriptions for i.MX8MQ SoC.
- Add JPEG encoder/decoder device nodes for i.MX8M SoCs.
- Update PMU compatible and drop interrupt-affinity for i.MX8M SoCs.
- Add Cadence HIFI4 DSP for i.MX8 MPlus SoC.
- A few small and random updates on various boards.
* tag 'imx-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (27 commits)
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
arm64: dts: ls1088a: add missing PMU node
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
arm64: dts: imx8mq-reform2: add sound support
arm64: dts: imx8m: drop interrupt-affinity for pmu
arm64: dts: imx8qxp: update pmu compatible
arm64: dts: imx8mm: update pmu compatible
arm64: dts: ls1046a: fix eeprom entries
arm64: dts: imx8mm-venice-gw7901: enable pull-down on gpio outputs
arm64: dts: imx8mm-venice-gw7901: add support for USB hub subload
arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
arm64: dts: imx8mm-venice-gw700x: fix invalid pmic pin config
arm64: dts: imx8mm-venice-gw700x: fix mp5416 pmic config
arm64: dts: imx8mq: add mipi csi phy and csi bridge descriptions
arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support
arm64: dts: imx8mp: Add dsp node
arm64: dts: imx8m: Replace deprecated fsl,usbphy DT props with phys
arm64: dts: imx8mq-evk: Remove unnecessary blank lines
arm64: dts: imx8mq-evk: add CD pinctrl for usdhc2
arm64: dts: imx8mm-venice-gw7901: Remove unnecessary #address-cells/#size-cells
...
Link: https://lore.kernel.org/r/20210814133853.9981-3-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 16 Aug 2021 21:01:09 +0000 (23:01 +0200)]
Merge tag 'imx-bindings-5.15' of git://git./linux/kernel/git/shawnguo/linux into arm/dt
i.MX DT bindings update for 5.15:
- Add vendor prefix for MNT Research GmbH, SKOV A/S and Traverse
Technologies.
- Add compatible for Nitrogen8 SoM, MNT Reform2, Traverse Ten64,
SKOV i.MX6, SolidSense and i.MX8M GW7902 boards.
- Add compatible for i.MX8QM JPEG codec.
* tag 'imx-bindings-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
dt-bindings: vendor-prefixes: add Traverse Technologies
dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
dt-bindings: arm: imx: add imx8mm/imx8mn GW7902 support
dt-bindings: arm: fsl: Add DHCOM PicoITX and DHCOM DRC02 boards
dt-bindings: arm: fsl: add SolidSense boards
dt-bindings: media: imx-jpeg: Add compatible for i.MX8QM JPEG codec
dt-bindings: arm: fsl: add MNT Reform2 board
dt-bindings: vendor-prefixes: add mntre
dt-bindings: arm: fsl: add Nitrogen8 SoM
Link: https://lore.kernel.org/r/20210814133853.9981-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 16 Aug 2021 21:00:02 +0000 (23:00 +0200)]
Merge tag 'tegra-for-5.15-arm64-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
arm64: tegra: Device tree changes for v5.15-rc1
Contains a couple of fixes across the board and adds support for the
recently released NVIDIA Jetson TX2 NX Developer Kit.
* tag 'tegra-for-5.15-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix compatible string for Tegra132 CPUs
arm64: tegra: Add missing interconnects property for USB on Tegra186
arm64: tegra: Add NVIDIA Jetson TX2 NX Developer Kit support
arm64: tegra: Add PWM nodes on Tegra186
arm64: tegra194: p2888: Correct interrupt trigger type of temperature sensor
arm64: tegra: Fix Tegra194 PCIe EP compatible string
Link: https://lore.kernel.org/r/20210813162157.2820913-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 16 Aug 2021 20:58:39 +0000 (22:58 +0200)]
Merge tag 'tegra-for-5.15-arm-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.15-rc1
The majority of this is temperature sensor additions for various devices
and fixes to the trigger type of the thermal interrupts.
Other than that there are various minor fixes across the board.
* tag 'tegra-for-5.15-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: tamonten: Fix UART pad setting
ARM: tegra: nexus7: Improve thermal zones
ARM: tegra: acer-a500: Improve thermal zones
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value
ARM: tegra: acer-a500: Add power supplies to accelerometer
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor
ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor
ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor
ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor
ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
ARM: tegra: acer-a500: Add interrupt to temperature sensor node
ARM: tegra: nexus7: Add interrupt to temperature sensor node
ARM: tegra: paz00: Add interrupt to temperature sensor node
ARM: tegra: ouya: Add interrupt to temperature sensor node
ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees
Link: https://lore.kernel.org/r/20210813162157.2820913-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 16 Aug 2021 20:56:07 +0000 (22:56 +0200)]
Merge tag 'tegra-for-5.15-dt-bindings' of git://git./linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.15-rc1
This contains a single patch that adds the compatible string for the
NVIDIA Jetson TX2 NX developer kit.
* tag 'tegra-for-5.15-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra: Document NVIDIA Jetson TX2 NX developer kit
Link: https://lore.kernel.org/r/20210813162157.2820913-1-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 16 Aug 2021 20:53:49 +0000 (22:53 +0200)]
Merge tag 'amlogic-arm64-dt-for-v5.15-v2' of git://git./linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM64 DT changes for v5.15 part 2:
- add audio to nodes vega-s95
- add audio to nodes nexbox-a1
* tag 'amlogic-arm64-dt-for-v5.15-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: meson: add audio playback to vega-s95 dtsi
arm64: dts: meson: add audio playback to nexbox-a1
Link: https://lore.kernel.org/r/47d77095-eee7-bbd9-d3aa-1dabeea3f0b9@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Mon, 16 Aug 2021 20:51:39 +0000 (22:51 +0200)]
Merge tag 'renesas-arm-dt-for-v5.15-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.15 (take two)
- Pin control, ADC, and CANFD support for the RZ/G2L SoC,
- Add interrupt-names properties to the Renesas RZ/A and RZ/G2L I2C
Bus Interface.
* tag 'renesas-arm-dt-for-v5.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: i2c: renesas,riic: Make interrupt-names required
arm64: dts: renesas: r9a07g044: Add I2C interrupt-names
ARM: dts: rza: Add I2C interrupt-names
dt-bindings: i2c: renesas,riic: Add interrupt-names
arm64: dts: renesas: r9a07g044: Add CANFD node
arm64: dts: renesas: r9a07g044: Add ADC node
arm64: dts: renesas: r9a07g044: Add pinctrl node
dt-bindings: clock: r9a07g044-cpg: Add entry for P0_DIV2 core clock
Link: https://lore.kernel.org/r/cover.1628849623.git.geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Mathew McBride [Tue, 10 Aug 2021 05:38:27 +0000 (05:38 +0000)]
dt-bindings: arm: fsl: Add Traverse Ten64 (LS1088A) board
Document the compatible for the Ten64 board which will
be included as freescale/fsl-ls1088a-ten64.dtb in arm64.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mathew McBride [Tue, 10 Aug 2021 05:38:26 +0000 (05:38 +0000)]
dt-bindings: vendor-prefixes: add Traverse Technologies
Traverse Technologies is a designer and manufacturer
of networking appliances.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mathew McBride [Tue, 10 Aug 2021 05:38:28 +0000 (05:38 +0000)]
arm64: dts: add device tree for Traverse Ten64 (LS1088A)
The Traverse Technologies Ten64 is a Mini-ITX form factor
networking board using the NXP LS1088A SoC.
This device tree only describes features which the mainline
kernel currently has support for, such as some I2C-connected
devices that are not described at present.
System documentation may be found at ten64doc.traverse.com.au
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> # for the MAC/PHY
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mathew McBride [Tue, 10 Aug 2021 05:38:25 +0000 (05:38 +0000)]
arm64: dts: ls1088a: add missing PMU node
The Performance Manager Unit was not described in the DTS
which meant performance event monitoring was not possible.
This was exposed by a change to the PMU handling in KVM
in 5.11-rc3 which now prevents a PMU being exposed to a
guest when the host does not provide one:
"KVM: arm64: Don't access PMCR_EL0 when no PMU is available"
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mathew McBride [Tue, 10 Aug 2021 05:38:24 +0000 (05:38 +0000)]
arm64: dts: ls1088a: add internal PCS for DPMAC1 node
A previous patch added the PCS for DPMAC2 only, as
used for the AQR PHY on the LS1088ARDB.
DPMAC1 PCS access is required for PHYLINK SFP support
on the Traverse Ten64 board.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Wed, 4 Aug 2021 04:34:38 +0000 (06:34 +0200)]
dt-bindings: arm: fsl: add SKOV imx6q and imx6dl based boards
Add SKOV imx6q/dl LT2, LT6 and mi1010ait-1cp1 boards.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Oleksij Rempel [Wed, 4 Aug 2021 04:34:37 +0000 (06:34 +0200)]
dt-bindings: vendor-prefixes: Add an entry for SKOV A/S
Add "skov" entry for the SKOV A/S: https://www.skov.com/en/
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Lucas Stach [Thu, 12 Aug 2021 19:47:12 +0000 (21:47 +0200)]
arm64: dts: imx8mq-reform2: add sound support
This adds sound support to the Reform2.
It differs from the downstream implementation in that the codec
is used as the BCLK and FSYNC master and the i.MX8MQ only supplies
a fixed 25MHz MCLK from the oscillator. This allows to support
a wider range of audio rates by using the codec PLL and to shut
down the audio PLLs on the i.MX8MQ SoC side.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Sat, 7 Aug 2021 09:45:37 +0000 (17:45 +0800)]
arm64: dts: imx8m: drop interrupt-affinity for pmu
i.MX8M use PPI for pmu, interrupt-affinity is not needed.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Sat, 7 Aug 2021 09:45:36 +0000 (17:45 +0800)]
arm64: dts: imx8qxp: update pmu compatible
i.MX8QXP features four Cortex-A35 cores, use more accurate
compatible.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Peng Fan [Sat, 7 Aug 2021 09:45:35 +0000 (17:45 +0800)]
arm64: dts: imx8mm: update pmu compatible
i.MX8MM features four Cortex-A53 cores, update the compatible
to use more accurate "arm,cortex-a53-pmu"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Raag Jadav [Wed, 4 Aug 2021 19:24:45 +0000 (00:54 +0530)]
arm64: dts: ls1046a: fix eeprom entries
ls1046afrwy and ls1046ardb boards have CAT24C04[1] and CAT24C05[2]
eeproms respectively. Both are 4Kb (512 bytes) in size,
and compatible with AT24C04[3].
Remove multi-address entries, as both the boards have a single chip each.
[1] https://www.onsemi.com/pdf/datasheet/cat24c01-d.pdf
[2] https://www.onsemi.com/pdf/datasheet/cat24c03-d.pdf
[3] https://ww1.microchip.com/downloads/en/DeviceDoc/doc0180.pdf
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Tue, 27 Jul 2021 16:11:01 +0000 (09:11 -0700)]
arm64: dts: imx8mm-venice-gw7901: enable pull-down on gpio outputs
Enable internal pull-down on UART transceiver GPIO config pins.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Tue, 27 Jul 2021 16:11:00 +0000 (09:11 -0700)]
arm64: dts: imx8mm-venice-gw7901: add support for USB hub subload
The USB hub has it's reset as GPIO4_IO17 but can be sub-loaded and
VBUS provided by a VBUS regulator with GPIO4_IO2 as the enable and
GPIO1_IO15 as the active-low over-current.
Enable pull-up for GPIO4_IO17 to keep hub out of reset and move VBUS
enable to GPIO4_IO2. Additionally enable pull-up on GPIO1_IO15 so that
if the hub is loaded it never over-currents.
This allows USB to work in both configurations without a device-tree
change.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Tue, 27 Jul 2021 16:10:59 +0000 (09:10 -0700)]
arm64: dts: imx8mm-venice-gw71xx: fix USB OTG VBUS
The GW71xx has a USB Type-C connector with USB 2.0 signaling. GPIO1_12
is the power-enable to the TPS25821 Source controller and power switch
responsible for monitoring the CC pins and enabling VBUS. Therefore
GPIO1_12 must always be enabled and the vbus output enable from the
IMX8MM can be ignored.
To fix USB OTG VBUS enable a pull-up on GPIO1_12 to always power the
TPS25821 and change the regulator output to GPIO1_10 which is
unconnected.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Tue, 27 Jul 2021 16:10:58 +0000 (09:10 -0700)]
arm64: dts: imx8mm-venice-gw700x: fix invalid pmic pin config
The GW700x PMIC does not have an interrupt. Remove the invalid pin
config.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Tue, 27 Jul 2021 16:10:57 +0000 (09:10 -0700)]
arm64: dts: imx8mm-venice-gw700x: fix mp5416 pmic config
Fix various MP5416 PMIC configurations:
- Update regulator names per dt-bindings
- ensure values fit among valid register values
- add required regulator-max-microamp property
- add regulator-always-on prop
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Martin Kepplinger [Mon, 26 Jul 2021 08:21:17 +0000 (10:21 +0200)]
arm64: dts: imx8mq: add mipi csi phy and csi bridge descriptions
Describe the 2 available CSI interfaces on the i.MX8MQ with the MIPI-CSI2
receiver (new driver) and the CSI Bridge that provides the user buffers
(existing driver).
An image sensor is to be connected to the MIPIs' second port, to be described
in board files.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Tim Harvey [Fri, 23 Jul 2021 18:41:16 +0000 (11:41 -0700)]
arm64: dts: imx: Add i.mx8mm/imx8mn Gateworks gw7902 dts support
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Daniel Baluta [Fri, 23 Jul 2021 11:05:40 +0000 (14:05 +0300)]
arm64: dts: imx8mp: Add dsp node
i.MX8 MPlus SoC integrates Cadence HIFI4 DSP. This core runs either a
custom firmware or the open source SOF firmware [1]
DSP device is handled by SOF OF driver found in
sound/soc/sof/sof-of-dev.c
Notice that the DSP node makes use of:
- dsp_reserved, a reserved memory region for various Audio
resources (e.g firmware loading, audio buffers, etc).
- Messaging Unit (mu2) for passing notifications betweem ARM
core and DSP.
[1] https://thesofproject.github.io/latest/platforms/index.html
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Marek Vasut [Wed, 21 Jul 2021 16:39:55 +0000 (18:39 +0200)]
arm64: dts: imx8m: Replace deprecated fsl,usbphy DT props with phys
The fsl,usbphy DT property is deprecated, replace it with phys DT
property and specify #phy-cells. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kwon Tae-young [Thu, 15 Jul 2021 07:07:49 +0000 (16:07 +0900)]
arm64: dts: imx8mq-evk: Remove unnecessary blank lines
Unnecessary blank lines do NOT help readability, so remove them.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kwon Tae-young [Thu, 15 Jul 2021 06:54:31 +0000 (15:54 +0900)]
arm64: dts: imx8mq-evk: add CD pinctrl for usdhc2
Add CD pinctrl for usdhc2.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fabio Estevam [Sat, 10 Jul 2021 12:39:41 +0000 (09:39 -0300)]
arm64: dts: imx8mm-venice-gw7901: Remove unnecessary #address-cells/#size-cells
The following dtc build warning is seen with W=1:
arch/arm64/boot/dts/freescale/imx8mm-venice-gw7901.dts:291.14-397.4: Warning (avoid_unnecessary_addr_size): /soc@0/bus@
30800000/i2c@
30a20000/gsc@20: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Remove the unnecessary #address-cells/#size-cells to fix it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Mirela Rabulea [Sat, 19 Jun 2021 14:36:11 +0000 (17:36 +0300)]
arm64: dts: imx8: Add jpeg encoder/decoder nodes
Add dts for imaging subsytem, include jpeg nodes here.
Tested on imx8qxp/qm.
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kwon Tae-young [Fri, 18 Jun 2021 07:27:33 +0000 (16:27 +0900)]
arm64: dts: imx8qxp-ai_ml: Fix checkpatch warnings
Fix the following warnings reported by checkpatch:
arch/..../imx8qxp-ai_ml.dts:198: WARNING: please, no space before tabs
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Tue, 15 Jun 2021 16:03:37 +0000 (19:03 +0300)]
arm64: dts: ls1088ardb: update PHY nodes with IRQ information
Describe the IRQs for both the QSGMII PHYs and the 10GBASE-R PHY found
on the LS1088ARDB board.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Tue, 15 Jun 2021 16:03:36 +0000 (19:03 +0300)]
arm64: dts: ls2088ardb: update PHY nodes with IRQ information
Update the DTS nodes corresponding to the 4 10GBASE-R PHYs to describe
their IRQ lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Tue, 15 Jun 2021 16:03:35 +0000 (19:03 +0300)]
arm64: dts: lx2160ardb: update PHY nodes with IRQ information
Update the DTS nodes for both the AR8035 and the AQR107 PHYs in order to
describe their IRQ lines.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Thierry Reding [Tue, 22 Jun 2021 13:44:22 +0000 (15:44 +0200)]
arm64: tegra: Fix compatible string for Tegra132 CPUs
The documented compatible string for the CPUs found on Tegra132 is
"nvidia,tegra132-denver", rather than the previously used compatible
string "nvidia,denver".
Signed-off-by: Thierry Reding <treding@nvidia.com>
Andreas Obergschwandtner [Thu, 29 Jul 2021 14:42:26 +0000 (16:42 +0200)]
ARM: tegra: tamonten: Fix UART pad setting
This patch fixes the tristate and pullup configuration for UART 1 to 3
on the Tamonten SOM.
Signed-off-by: Andreas Obergschwandtner <andreas.obergschwandtner@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:47 +0000 (00:19 +0300)]
ARM: tegra: nexus7: Improve thermal zones
Use skin temperature for maintaining temperature that is suitable
specifically for Nexus 7. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:46 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Improve thermal zones
Use skin temperature for maintaining temperature that is suitable
specifically for A500. Add CPU thermal zone that protects silicon.
All these changes don't make a significant difference, but it is a
more correct definition of thermal zones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:45 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Use verbose variant of atmel,wakeup-method value
The verbose variant of the atmel,wakeup-method value was lost when patch
that added the property was merged because it conflicted with other patch,
re-add it for consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:44 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Add power supplies to accelerometer
Add power supplies to accelerometer node, for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:43 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Remove bogus USB VBUS regulators
The configuration of USB VBUS regulators was borrowed from downstream
kernel, which is incorrect because the corresponding GPIOs are connected
to PROX_EN (A501 3G model) and LED_EN pins in accordance to the board
schematics. USB works fine with both GPIOs being disabled, so remove the
bogus USB VBUS regulators. The USB VBUS of USB3 is supplied from the fixed
5v system regulator and device-mode USB1 doesn't have VBUS switches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:42 +0000 (00:19 +0300)]
ARM: tegra: jetson-tk1: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:41 +0000 (00:19 +0300)]
ARM: tegra: dalmore: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:40 +0000 (00:19 +0300)]
ARM: tegra: cardhu: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:39 +0000 (00:19 +0300)]
ARM: tegra: apalis: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:38 +0000 (00:19 +0300)]
ARM: tegra: nyan: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:37 +0000 (00:19 +0300)]
ARM: tegra: acer-a500: Add interrupt to temperature sensor node
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:36 +0000 (00:19 +0300)]
ARM: tegra: nexus7: Add interrupt to temperature sensor node
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:35 +0000 (00:19 +0300)]
ARM: tegra: paz00: Add interrupt to temperature sensor node
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor for completeness.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:34 +0000 (00:19 +0300)]
ARM: tegra: ouya: Add interrupt to temperature sensor node
The TEMP_ALERT pin of LM90 temperature sensor is connected to Tegra SoC.
Add interrupt property to the temperature sensor and enable it in pinmux,
for completeness.
Tested-by: Matt Merhar <mattmerhar@protonmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Dmitry Osipenko [Mon, 2 Aug 2021 21:19:33 +0000 (00:19 +0300)]
ARM: tegra: Add SoC thermal sensor to Tegra30 device-trees
Add the on-chip SoC thermal sensor to Tegra30 device-trees. Now CPU
temperature reporting and thermal throttling is available on all Tegra30
devices universally.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Arnd Bergmann [Thu, 12 Aug 2021 20:56:26 +0000 (22:56 +0200)]
Merge tag 'omap-for-v5.15/dt-am3-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Changes for am3 cpsw and SanCloud for v5.15
A series of changes to update am3 to use cpsw switch driver and
few updates to earlier SanCloud changes. The plan was to send the
cpsw switch driver changes earlier but looks like I never tagged
the mail thread in my inbox to apply for v5.15.
* tag 'omap-for-v5.15/dt-am3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-sancloud-bbe: Drop usb wifi comment
ARM: dts: am335x-sancloud-bbe: Fix missing pinctrl refs
ARM: dts: am335x-bone: switch to new cpsw switch drv
ARM: dts: am33xx: update ethernet aliases
ARM: dts: am335x-sl50: switch to new cpsw switch drv
ARM: dts: am335x-shc: switch to new cpsw switch drv
ARM: dts: am335x-phycore: switch to new cpsw switch drv
ARM: dts: am335x-pepper: switch to new cpsw switch drv
ARM: dts: am335x-pdu001: switch to new cpsw switch drv
ARM: dts: am335x-osd3358-sm-red: switch to new cpsw switch drv
ARM: dts: am335x-myirtech: switch to new cpsw switch drv
ARM: dts: am335x-moxa-uc: switch to new cpsw switch drv
ARM: dts: am335x-lxm: switch to new cpsw switch drv
ARM: dts: am335x-igep0033: switch to new cpsw switch drv
ARM: dts: am335x-cm-t335: switch to new cpsw switch drv
ARM: dts: am335x-chiliboard: switch to new cpsw switch drv
ARM: dts: am335x-nano: switch to new cpsw switch drv
ARM: dts: am335x-baltos: switch to new cpsw switch drv
Link: https://lore.kernel.org/r/pull-1628751694-126144@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:55:50 +0000 (22:55 +0200)]
Merge tag 'samsung-dt64-5.15' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM64 changes for v5.15
1. Add CPU topology and cache information to Exynos DTSI files.
2. Correct GIC CPU interfaces address range on Exynos7.
* tag 'samsung-dt64-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
arm64: dts: exynos: correct GIC CPU interfaces address range on Exynos7
arm64: dts: exynos: add CPU topology to Exynos5433
arm64: dts: exynos: Add cpu cache information to Exynos5433
arm64: dts: exynos: Add cpu cache information to Exynos7
Link: https://lore.kernel.org/r/20210811085128.30103-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:55:17 +0000 (22:55 +0200)]
Merge tag 'samsung-dt-5.15' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.15
Add CPU topology to all Exynos DTSI files.
* tag 'samsung-dt-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add CPU topology to Exynos5422
ARM: dts: exynos: add CPU topology to Exynos5420
ARM: dts: exynos: add CPU topology to Exynos5260
ARM: dts: exynos: add CPU topology to Exynos5250
ARM: dts: exynos: add CPU topology to Exynos4412
ARM: dts: exynos: add CPU topology to Exynos4210
ARM: dts: exynos: add CPU topology to Exynos3250
Link: https://lore.kernel.org/r/20210811085128.30103-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:54:50 +0000 (22:54 +0200)]
Merge tag 'amlogic-arm-dt-for-v5.15' of git://git./linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM DT changes for v5.15:
- meson8: use a default higher default GPU clock to solve probe failure
- meson: add AIU audio controller and codec for ec100
- meson8b: fix pwm regulator supply property name
* tag 'amlogic-arm-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
ARM: dts: meson8b: ec100: Fix the pwm regulator supply properties
ARM: dts: meson8b: mxq: Fix the pwm regulator supply properties
ARM: dts: meson8b: odroidc1: Fix the pwm regulator supply properties
ARM: dts: meson8b: ec100: wire up the RT5640 audio codec
ARM: dts: meson: Add the AIU audio controller
ARM: dts: meson8: Use a higher default GPU clock frequency
Link: https://lore.kernel.org/r/87519792-c9e7-76a6-5db5-0e955286b564@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:53:54 +0000 (22:53 +0200)]
Merge tag 'amlogic-arm64-dt-for-v5.15' of git://git./linux/kernel/git/amlogic/linux into arm/dt
Amlogic ARM64 DT changes for v5.15:
- nanoki-k2: enable bluetooth
- khadas vim & vim2: improve wifi
* tag 'amlogic-arm64-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/amlogic/linux:
arm64: dts: meson: improve gxm-khadas-vim2 wifi
arm64: dts: meson: improve gxl-s905x-khadas-vim wifi
arm64: dts: meson-gxbb: nanopi-k2: Enable Bluetooth
Link: https://lore.kernel.org/r/032895d9-62b6-6c9e-b04b-9c3d316f27ec@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:52:49 +0000 (22:52 +0200)]
Merge tag 'ti-k3-dt-for-v5.15' of git://git./linux/kernel/git/nmenon/linux into arm/dt
Devicetree changes for TI K3 platforms for v5.15 merge window:
* New features:
- AM64 adds pwm and ecap capability
* tag 'ti-k3-dt-for-v5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/nmenon/linux:
arm64: dts: ti: k3-am642-sk: Add pwm nodes
arm64: dts: ti: k3-am642-evm: Add pwm nodes
arm64: dts: ti: k3-am64-main: Add ecap pwm nodes
arm64: dts: ti: k3-am64-main: Add epwm nodes
Link: https://lore.kernel.org/r/20210809130631.pfvntcichsyeekbo@festive
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:52:10 +0000 (22:52 +0200)]
Merge tag 'v5.14-next-dts64' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
MT8173:
- Add regulator for MFG_ASYNC power domain
- Use alias for MMC to get fixed numbers
MT8183:
- Use alia for MMC to get fixed numbers
- Add optional event number for Global Comman Engine
* tag 'v5.14-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: mediatek: Add optional mediatek,gce-events property
arm64: dts: mt8183: add mediatek,gce-events in mutex
arm64: dts: mediatek: mt8173: Add domain supply for mfg_async
arm64: dts: mt8173: elm: Use aliases to mmc nodes
arm64: dts: mt8183: kukui: Use aliases to mmc nodes
Link: https://lore.kernel.org/r/26c4026a-9f26-d5a3-c30f-439120a4eaa0@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:51:23 +0000 (22:51 +0200)]
Merge tag 'v5.14-next-dts32' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
Increase trip point on MT7623
* tag 'v5.14-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt7623: increase passive cooling trip
Link: https://lore.kernel.org/r/289ded1c-dae7-54ef-6b56-9433bfcaf9de@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:50:18 +0000 (22:50 +0200)]
Merge tag 'ixp4xx-dts-arm-soc-v5.15-1' of git://git./linux/kernel/git/linusw/linux-nomadik into arm/dt
IXP4xx DTS file updates for the v5.15 kernel cycle:
- Fix up some (non-urgent) IRQ flags for the PCI buses.
- Add the second UART to the generic ixp4xx.dtsi
- Make use of the new expansion bus driver in all device
trees with e.g. flash memory on the expansion bus.
- Adds the CF card slot to the Gateworks GW2358.
- Add new device trees for:
- Iomega NAS 100D
- D-Link DSM-G600
- Netgear WG302v2
- Arcom Vulcan
- Gateworks Avila GW2348
- Intel IXPD425 and siblings
- Coyote and IXDPG425
- Linksys WRV54G
* tag 'ixp4xx-dts-arm-soc-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: ixp4xx: Add a devicetree for Freecom FSG-3
ARM: dts: ixp4xx: Add devicetree for Linksys WRV54G
ARM: dts: ixp4xx: Add device trees for Coyote and IXDPG425
ARM: dts: ixp4xx: Add Intel IXDP425 etc reference designs
ARM: dts: ixp4xx: Add CF to GW2358
ARM: dts: ixp4xx: Add Gateworks Avila GW2348 device tree
ARM: dts: ixp4xx: Add Arcom Vulcan device tree
ARM: dts: ixp4xx: Add devicetree for Netgear WG302v2
ARM: dts: ixp4xx: Use the expansion bus
ARM: dts: ixp4xx: Add second UART
ARM: dts: ixp4xx: Add devicetree for D-Link DSM-G600 rev A
ARM: dts: ixp4xx: Move EPBX100 flash to external bus node
ARM: dts: ixp4xx: Add devicetree for Iomega NAS 100D
ARM: dts: ixp4xx: Fix up bad interrupt flags
Link: https://lore.kernel.org/r/CACRpkdY19AvWT--OcmEKbwFue_EcThVs7uZeHkzORten7xj-RA@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:49:21 +0000 (22:49 +0200)]
Merge tag 'stm32-dt-for-v5.15-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT for v5.15, round 1
Highlights:
----------
-MPU:
- ST boards:
- Add coporcessor detach mailbox on ED and DKx boards
- Fix dtbs_check SAI warnings
- DH boards:
-Fix some dtbs_check warnings: usb, backlight, hdmi
* tag 'stm32-dt-for-v5.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: Update AV96 adv7513 node per dtbs_check
ARM: dts: stm32: Set {bitclock,frame}-master phandles on ST DKx
ARM: dts: stm32: Add coprocessor detach mbox on stm32mp15x-dkx boards
ARM: dts: stm32: Add coprocessor detach mbox on stm32mp157c-ed1 board
ARM: dts: stm32: Add usbphyc_port1 supply on DHCOM SoM
ARM: dts: stm32: Add backlight and panel supply on DHCOM SoM
ARM: dts: stm32: Set {bitclock,frame}-master phandles on DHCOM SoM
ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM
ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM
ARM: dts: stm32: Prefer HW RTC on DHCOM SoM
Link: https://lore.kernel.org/r/e4f0bea3-4065-38d5-f1b2-007e4094c4a8@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:48:17 +0000 (22:48 +0200)]
Merge tag 'sti-dt-for-v5.15-round1' of git://git./linux/kernel/git/pchotard/sti into arm/dt
Highlights:
-----------
- Introduce 4KOpen STiH418-b2264 board
- Remove clk_ignore_unused from STi boards DT
- Remove clock-output-names and clk_critical properties
- Update some clock compatible
* tag 'sti-dt-for-v5.15-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih410-b2260
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih418-b2199
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih410-b2120
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih407-b2120
ARM: dts: sti: Introduce 4KOpen (stih418-b2264) board
ARM: dts: sti: add the thermal sensor node within stih418
ARM: dts: sti: disable rng11 on the stih418 platform
ARM: dts: sti: add the spinor controller node within stih407-family
ARM: dts: sti: update clkgen-fsyn entries in stih418-clock
ARM: dts: sti: update clkgen-fsyn entries in stih410-clock
ARM: dts: sti: update clkgen-fsyn entries in stih407-clock
ARM: dts: sti: update clkgen-pll entries in stih418-clock
ARM: dts: sti: update clkgen-pll entries in stih410-clock
ARM: dts: sti: update clkgen-pll entries in stih407-clock
ARM: dts: sti: update flexgen compatible within stih410-clock
ARM: dts: sti: update flexgen compatible within stih407-clock
ARM: dts: sti: update flexgen compatible within stih418-clock
Link: https://lore.kernel.org/r/1d95209f-9cb4-47a3-2696-7a93df7cdc05@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 12 Aug 2021 20:47:01 +0000 (22:47 +0200)]
Merge tag 'omap-for-v5.15/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
Devicetree changes for omaps for v5.15
Devicetree changes for omaps to configure more devices, and
add support for new SoC variants and devices:
- Add add gpio-line-names for am335x-boneblue
- Add support for dra762 abz package
- Two patches for McASP support on omap4
- Three patches to add support for am335x-sancloud-bbe-lite
- A series of changes to configure PRUSS for am3/4/5
* tag 'omap-for-v5.15/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx: Add PRUSS MDIO controller nodes
ARM: dts: am57xx: Add PRU-ICSS nodes
ARM: dts: am4372: Add PRUSS MDIO controller node
ARM: dts: am4372: Add the PRU-ICSS0 DT node
ARM: dts: am4372: Add the PRU-ICSS1 DT node
ARM: dts: am335x-icev2: Enable PRU-ICSS module
ARM: dts: am335x-evmsk: Enable PRU-ICSS module
ARM: dts: am335x-evm: Enable PRU-ICSS module
ARM: dts: am335x-bone-common: Enable PRU-ICSS node
ARM: dts: am33xx-l4: Add PRUSS MDIO controller node
ARM: dts: am33xx-l4: Add PRUSS node
ARM: dts: am335x-sancloud-bbe-lite: New devicetree
ARM: dts: am335x-sancloud-bbe: Extract common code
ARM: dts: am335x-boneblack: Extract HDMI config
ARM: dts: omap4-l4-abe: Add McASP configuration
ARM: dts: omap4-l4-abe: Correct sidle modes for McASP
ARM: dts: Add support for dra762 abz package
ARM: dts: am335x-boneblue: add gpio-line-names
Link: https://lore.kernel.org/r/pull-1628153040-834155@atomide.com-3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Thierry Reding [Thu, 12 Aug 2021 14:17:12 +0000 (16:17 +0200)]
arm64: tegra: Add missing interconnects property for USB on Tegra186
The device tree node for the XUDC (USB device mode controller) is
missing the interconnects property that describes the path to memory for
the controller. Add the property so that the things like the DMA mask
can be set by the operating system.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 12 Aug 2021 12:26:17 +0000 (14:26 +0200)]
arm64: tegra: Add NVIDIA Jetson TX2 NX Developer Kit support
The Jetson TX2 NX Developer Kit is very similar to the Jetson Nano, but
uses the more powerful Tegra186 SoC.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 12 Aug 2021 12:26:16 +0000 (14:26 +0200)]
arm64: tegra: Add PWM nodes on Tegra186
These PWMs can be used for fan or LED backlight control. Add the device
tree nodes for all existing controllers found on Tegra186 SoCs. None of
these are enabled by default, which is left for the board DTS files to
do when necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Thierry Reding [Thu, 12 Aug 2021 12:26:15 +0000 (14:26 +0200)]
dt-bindings: tegra: Document NVIDIA Jetson TX2 NX developer kit
The Jetson TX2 NX Developer Kit is the same form factor as Jetson Nano,
but uses the more powerful Tegra186 SoC for added performance.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Geert Uytterhoeven [Wed, 14 Jul 2021 13:20:03 +0000 (15:20 +0200)]
dt-bindings: i2c: renesas,riic: Make interrupt-names required
Now the I2C device nodes in all DTS files have gained "interrupt-names"
properties, the "interrupt-names" property can be made required.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/da8d1973dcd419d8d9c8c662ee614952f3a6969e.1626267422.git.geert+renesas@glider.be
Geert Uytterhoeven [Wed, 14 Jul 2021 13:20:02 +0000 (15:20 +0200)]
arm64: dts: renesas: r9a07g044: Add I2C interrupt-names
Add "interrupt-names" properties to the I2C device nodes, to make it
easier to review the interrupt mappings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/d35ba11bd705e3c728f94ff0414ac6ae1156244f.1626267422.git.geert+renesas@glider.be
Geert Uytterhoeven [Wed, 14 Jul 2021 13:20:01 +0000 (15:20 +0200)]
ARM: dts: rza: Add I2C interrupt-names
Add "interrupt-names" properties to the I2C device nodes of the RZ/A1H
and RZ/A2M DTS files, to make it easier to review the interrupt mappings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/7a073439e37f6672e4809af0a2ee9cd4ac820ec6.1626267422.git.geert+renesas@glider.be
Geert Uytterhoeven [Wed, 14 Jul 2021 13:20:00 +0000 (15:20 +0200)]
dt-bindings: i2c: renesas,riic: Add interrupt-names
The Renesas RZ/A and RZ/G2L I2C Bus Interface has no less than 8
interrupts. Hence document the "interrupt-names" property, to make it
easier to review the interrupt mappings in DTS files.
Note that this property cannot be made required yet, as the RIIC nodes
in all DTS files lack the property.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/a81d0e14e395f297666e8c3a8ce3e292d2606a65.1626267422.git.geert+renesas@glider.be
Dmitry Osipenko [Sun, 11 Jul 2021 23:49:39 +0000 (02:49 +0300)]
arm64: tegra194: p2888: Correct interrupt trigger type of temperature sensor
The LM90 temperature sensor should use edge-triggered interrupt because
LM90 hardware doesn't deassert interrupt line until temperature is back
to normal state, which results in interrupt storm. Correct the interrupt
trigger type.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Lad Prabhakar [Tue, 27 Jul 2021 13:30:22 +0000 (14:30 +0100)]
arm64: dts: renesas: r9a07g044: Add CANFD node
Add CANFD node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727133022.634-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven [Tue, 10 Aug 2021 11:35:03 +0000 (13:35 +0200)]
Merge tag 'renesas-r9a07g044-dt-binding-defs-tag2' into HEAD
Renesas RZ/G2L DT Binding Definitions Update
Missing definition for the P0_DIV2 core clock on the Renesas RZ/G2L
(R9A07G044) SoC, shared by driver and DT source files.
Lad Prabhakar [Wed, 4 Aug 2021 20:21:18 +0000 (21:21 +0100)]
arm64: dts: renesas: r9a07g044: Add ADC node
Add ADC node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210804202118.25745-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Lad Prabhakar [Tue, 27 Jul 2021 11:23:27 +0000 (12:23 +0100)]
arm64: dts: renesas: r9a07g044: Add pinctrl node
Add GPIO/pinctrl node to R9A07G044 (RZ/G2L) SoC DTSI.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727112328.18809-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Christian Hewitt [Wed, 4 Aug 2021 14:02:58 +0000 (14:02 +0000)]
arm64: dts: meson: add audio playback to vega-s95 dtsi
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Tested-by: Oleg Ivanov <150balbes@yandex.ru>
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210804140258.4666-1-christianshewitt@gmail.com
Christian Hewitt [Wed, 4 Aug 2021 14:00:29 +0000 (14:00 +0000)]
arm64: dts: meson: add audio playback to nexbox-a1
Add initial support limited to HDMI i2s and SPDIF (LPCM).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20210804140029.4445-1-christianshewitt@gmail.com
Paul Barker [Fri, 6 Aug 2021 08:59:07 +0000 (09:59 +0100)]
ARM: dts: am335x-sancloud-bbe: Drop usb wifi comment
The wifi chip on USB port 4 may not be present on all BBE variants.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Paul Barker [Fri, 6 Aug 2021 08:59:06 +0000 (09:59 +0100)]
ARM: dts: am335x-sancloud-bbe: Fix missing pinctrl refs
pinctrl settings for the USB hub, barometer & accelerometer need to be
referenced from the relevant nodes to work.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Krzysztof Kozlowski [Thu, 5 Aug 2021 07:21:10 +0000 (09:21 +0200)]
arm64: dts: exynos: correct GIC CPU interfaces address range on Exynos7
The GIC-400 CPU interfaces address range is defined as 0x2000-0x3FFF (by
ARM).
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Reported-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixes:
b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Link: https://lore.kernel.org/r/20210805072110.4730-1-krzysztof.kozlowski@canonical.com
Linus Walleij [Thu, 29 Jul 2021 14:34:57 +0000 (16:34 +0200)]
ARM: dts: ixp4xx: Add a devicetree for Freecom FSG-3
This adds a devicetree for the Freecom FSG-3, a combined router
and NAS.
Cc: Rod Whitby <rod@whitby.id.au>
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 29 Jul 2021 08:15:56 +0000 (10:15 +0200)]
ARM: dts: ixp4xx: Add devicetree for Linksys WRV54G
This adds a device tree for the Linksys WRV54G also known as
Gemtek GTWX5715. Some enhancements have been folded in from the
OpenWrt patches.
This supports everything in the upstream kernel with placeholders
for the out-of-tree multiphy which exist in OpenWrt.
Cc: phj@phj.hu
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 28 Jul 2021 15:04:17 +0000 (17:04 +0200)]
ARM: dts: ixp4xx: Add device trees for Coyote and IXDPG425
This adds device trees for the ADI Engineering Coyote and the
Intel IXDPG425 reference design. The ethernet set-up on the
IXDPG425 is a bit dubious because I think it uses a DSA
switch chip, but this is a good as it gets right now.
The Coyote boardfile claims an IDE port exist at 0xFFFE1000
but the implementation does not use this. If you have the
board and can/want to test, please contact me.
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Cc: Zoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 27 Jul 2021 22:11:59 +0000 (00:11 +0200)]
ARM: dts: ixp4xx: Add Intel IXDP425 etc reference designs
The IXDP425, IXCDP1100, KIXRP435 and IXDP465 are similar Intel reference
designs for IXP42x, IXP43x and IXP4[56]x.
This adds device trees for these so the board files can be migrated.
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Mon, 26 Jul 2021 08:27:49 +0000 (10:27 +0200)]
ARM: dts: ixp4xx: Add CF to GW2358
This adds support for the compact flash card slot on the
Gateworks GW2358 router.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 27 Jul 2021 08:05:54 +0000 (10:05 +0200)]
ARM: dts: ixp4xx: Add Gateworks Avila GW2348 device tree
This adds a device tree file for the Gateworks Avila GW2348 platform
supporting all the features of the in-kernel boardfiles.
There are more boards in the Avila family, but this is the one that
is supported out-of-the-box by the current boardfiles. Some extra
features have been folded in from the upstream OpenWrt sources,
such as proper ethernet setup for both ethernet ports.
More variants can be added based on this device tree. Some of those
have DSA switches, multiple LEDs, multiple serial ports and similar
and would need some more elaborate work.
Cc: Michael-Luke Jones <mlj28@cam.ac.uk>
Cc: Deepak Saxena <dsaxena@plexity.net>
Cc: Tom Billman <kernel@giantshoulderinc.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Fri, 16 Jul 2021 23:00:21 +0000 (01:00 +0200)]
ARM: dts: ixp4xx: Add Arcom Vulcan device tree
This adds a device tree for the Arcom Vulcan IXP42x board.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 20 Jul 2021 08:59:54 +0000 (10:59 +0200)]
ARM: dts: ixp4xx: Add devicetree for Netgear WG302v2
This adds a devicetree for the Netgear WG302v2 router.
The DTS is mostly based on the upstream boardfile but I also
added in the ethernet from OpenWrt to get a more complete
system.
Cc: Imre Kaloz <kaloz@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Thu, 15 Jul 2021 23:58:54 +0000 (01:58 +0200)]
ARM: dts: ixp4xx: Use the expansion bus
Replace the "simple-bus" simplification by the proper bus for
IXP4xx memory or device expansion.
Use chip-select addressing with two address cells on all the
flashes mounted on the IXP4xx devices. This includes all flash
chips.
Change the unit-name from @
50000000 to @
c4000000 as the DTS
validation screams. The registers for controlling the bus are
at
c4000000 but the actual memory windows and ranges are at
50000000. Well it is just syntax, we can live with it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Mon, 19 Jul 2021 11:14:16 +0000 (13:14 +0200)]
ARM: dts: ixp4xx: Add second UART
The IXP4xx has two UARTs and some platforms make use of the
second one so add this to the include DTSI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 14 Jul 2021 14:15:36 +0000 (16:15 +0200)]
ARM: dts: ixp4xx: Add devicetree for D-Link DSM-G600 rev A
This adds a devicetree for the D-Link DSM-G600 Wireless Network
Storage Enclosure so that we can delete the boardfile. The boardfile
does not even define an ethernet interface as it has an external
ethernet on PCI. This devicetree is for revision A using IXP420
the rev B version uses PowerPC.
Cc: Michael-Luke Jones <mlj28@cam.ac.uk>
Cc: Rod Whitby <rod@whitby.id.au>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Michael Westerhof <mwester@dls.net>
Cc: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 14 Jul 2021 11:37:59 +0000 (13:37 +0200)]
ARM: dts: ixp4xx: Move EPBX100 flash to external bus node
This moves the EPBX100 flash under the external bus on CS0
like on the other IXP4xx systems.
Cc: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Tue, 15 Jun 2021 22:53:38 +0000 (00:53 +0200)]
ARM: dts: ixp4xx: Add devicetree for Iomega NAS 100D
This creates a more or less fully featured device tree for the
IXP42x-based Iomega NAS 100D.
We can't read out the raw flash contents for ethernet MAC, and
we cannot handle a power-off-button inside the kernel like the
boardfile does. These two things are normally done in userspace.
This conversion is part of moving all of the IXP4xx board files
over to device tree to modernize the IXP4xx kernel.
Cc: Rod Whitby <rod@whitby.id.au>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Wed, 28 Jul 2021 08:39:34 +0000 (10:39 +0200)]
ARM: dts: ixp4xx: Fix up bad interrupt flags
The PCI hosts had bad IRQ semantics, these are all active low.
Use the proper define and fix all in-tree users.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Patrice Chotard [Tue, 3 Aug 2021 12:37:48 +0000 (14:37 +0200)]
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih410-b2260
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrice Chotard [Tue, 3 Aug 2021 12:37:36 +0000 (14:37 +0200)]
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih418-b2199
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Patrice Chotard [Tue, 3 Aug 2021 12:37:24 +0000 (14:37 +0200)]
ARM: dts: sti: remove clk_ignore_unused from bootargs for stih410-b2120
Remove clk_ignore_unused from bootargs as it's no more needed.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
projects / platform / kernel / linux-rpi.git / log