Vladimir Zapolskiy [Sat, 19 Dec 2015 21:41:23 +0000 (23:41 +0200)]
lpc32xx: devkit3250: update board configuration file
The change updates DevKit3250 board powerd by NXP LPC3250 SoC:
* due to increased resulting U-boot image size give more space to
store loaded and relocated versions,
* add DMA support, which is used by NAND SLC driver,
* add NXP OHCI and PHY drivers to the image,
* add USB, JFFS and FAT commands.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Vladimir Zapolskiy [Sat, 19 Dec 2015 21:29:26 +0000 (23:29 +0200)]
arm: lpc32xx: switch SPL builds to driver model
For NXP LPC32xx boards the change enables SPL_DM option, this allows
to use any driver model UART driver in SPL images, hence a restriction
on HSUART in SPL image is removed and well as definitions for non-DM
NS16550 driver, its DM version is used instead.
Because SPL_DM requires malloc(), enable CONFIG_SPL_SYS_MALLOC_SIMPLE
for LPC32xx boards.
The change adds about 5KB to the resulting SPL image (for devkit3250
board SPL image is increased from 10672 to 15608 bytes).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vladimir Zapolskiy [Sat, 19 Dec 2015 21:29:25 +0000 (23:29 +0200)]
arm: lpc32xx: switch serial console to driver model
On NXP LPC32xx platform for non-SPL builds the change adds
standard (NS16550) and high-speed UARTs to driver model.
Due to specific of DM NS16550 device description UART clock can not be
got in runtime and by default it is set to 13MHz, if board PERIPH_CLK
is different, this should be specified in board configuration file.
For SPL builds HSUARTs are disabled and non-DM NS16550 driver is
compiled, if needed.
The change also updates default configs of devkit3250 and work_92105
boards to reflect updates in platform files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Vladimir Zapolskiy [Sat, 19 Dec 2015 21:29:24 +0000 (23:29 +0200)]
serial: lpc32xx hsuart: port driver to driver model
The change ports NXP LPC32xx 14-clock UART device driver to driver
model.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stephen Warren [Mon, 14 Dec 2015 22:01:15 +0000 (15:01 -0700)]
test/fs: error case fixes/enhancements
- Use "mkdir -p" to avoid errors when intermediate directories are
missing.
- Fall back to "dd" when "fallocate" fails. For example, fallocate isn't
supported on ext4.
- Add error checking for test image generation. Without this, the test
simply plows on spewing all kinds of errors which are hard to
immediately root-cause.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tom Rini [Thu, 10 Dec 2015 21:46:03 +0000 (16:46 -0500)]
omap4_panda: Convert to config_distro_bootcmd.h
Based on the am335x_evm conversion, switch to config_distro_bootcmd for
mmc and pxe. Tested with Fedora 23.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 10 Dec 2015 21:46:02 +0000 (16:46 -0500)]
ti_armv7_common.h: Add CONFIG_CMD_EXT4_WRITE
Given that with config_distro_defaults.h we always have ext4 read
support, add in write support.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 10 Dec 2015 21:46:01 +0000 (16:46 -0500)]
am335x_evm.h: unsed CONFIG_BOOTDELAY
Now that ti_armv7_common.h uses config_distro_defaults.h we don't need
to include it again and then undef CONFIG_BOOTDELAY
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 10 Dec 2015 21:42:21 +0000 (16:42 -0500)]
ext4_common.c: Clean up failure cases in alloc_triple_indirect_block
As noted by Coverity, when we have an error in
alloc_triple_indirect_block we will leak ti_pbuff_start_addr as it's not
being freed. Further inspection here shows that we could also leak
ti_cbuff_start_addr in one corner case so free that as well.
Reported-by: Coverity (CID 131205, 131206)
Signed-off-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Mon, 7 Dec 2015 18:38:50 +0000 (11:38 -0700)]
ums: support multiple LUNs at once
Extend the ums command to accept a list of block devices. Each of these
will be exported as a separate LUN. An example use-case would be:
ums 0 mmc 0,0.1,0.2
... which would export LUNs for eMMC 0's user data, boot0, and boot1 HW
partitions. This is useful since it allows the host access to everything
on the eMMC without having to somehow stop the ums command from executing
and restart it with different parameters.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Mon, 7 Dec 2015 18:38:49 +0000 (11:38 -0700)]
mmc: store hwpart in the block device
This will allow us to have multiple block device structs each referring
to the same eMMC device, yet different HW partitions.
For now, there is still a single block device per eMMC device. As before,
this block device always accesses whichever HW partition was most recently
selected. Clients wishing to make use of multiple block devices referring
to different HW partitions can simply take a copy of this block device
once it points at the correct HW partition, and use each one as they wish.
This feature will be used by the next patch.
In the future, perhaps get_device() could be enhanced to return a
dynamically allocated block device struct, to avoid the client needing to
copy it in order to maintain multiple block devices. However, this would
require all users to be updated to free those block device structs at some
point, which is rather a large change.
Most callers of mmc_switch_part() wish to permanently switch the default
MMC block device's HW partition. Enhance mmc_switch_part() so that it does
this. This removes the need for callers to do this. However,
common/env_mmc.c needs to save and restore the current HW partition. Make
it do this more explicitly.
Replace use of mmc_switch_part() with mmc_select_hwpart() in order to
remove duplicate code that skips the call if that HW partition is already
selected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Stephen Warren [Mon, 7 Dec 2015 18:38:48 +0000 (11:38 -0700)]
block: pass block dev not num to read/write/erase()
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Albert ARIBAUD [Wed, 25 Nov 2015 16:56:33 +0000 (17:56 +0100)]
arm: move gd handling outside of C code
As of gcc 5.2.1 for Thumb-1, it is not possible any
more to assign gd from C code, as gd is mapped to r9,
and r9 may now be saved in the prolog sequence, and
restored in the epilog sequence, of any C functions.
Therefore arch_setup_gd(), which is supposed to set
r9, may actually have no effect, causing U-Boot to
use a bad address to access GD.
Fix this by never calling arch_setup_gd() for ARM,
and instead setting r9 in arch/arm/lib/crt0.S, to
the value returned by board_init_f_alloc_reserve().
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Albert ARIBAUD [Wed, 25 Nov 2015 16:56:32 +0000 (17:56 +0100)]
Fix board init code to respect the C runtime environment
board_init_f_mem() alters the C runtime environment's
stack it is actually already using. This is not a valid
behaviour within a C runtime environment.
Split board_init_f_mem into C functions which do not alter
their own stack and always behave properly with respect to
their C runtime environment.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Tom Rini [Wed, 13 Jan 2016 23:27:40 +0000 (18:27 -0500)]
Merge branch 'master' of git://denx.de/git/u-boot-microblaze
Tom Rini [Wed, 13 Jan 2016 23:03:05 +0000 (18:03 -0500)]
Merge git://git.denx.de/u-boot-net
Tom Rini [Tue, 5 Jan 2016 13:47:48 +0000 (08:47 -0500)]
hash.c: Conditionally compile hash_command, static hash_show
The function hash_show is now only called by hash_command, so mark it as
static (and drop from hash.h). We only call hash_command when any of
CONFIG_CMD_CRC32, CONFIG_CMD_SHA1SUM or CONFIG_CMD_HASH are set. Since
hash.c is linked in unconditionally we must take extra care with
functions that bring in read-only strings as these will not be
discarded.
Signed-off-by: Tom Rini <trini@konsulko.com>
Stefan Monnier [Tue, 25 Aug 2015 19:24:13 +0000 (15:24 -0400)]
part_dos.c: Don't wrap to negative after 2G sectors
In order to support large IDE disks we need to make certain types be
lbaint_t now.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Stefan Monnier <monnier@iro.umontreal.ca>
Masahiro Yamada [Thu, 17 Dec 2015 08:19:35 +0000 (17:19 +0900)]
image: check "bootm_low" and "bootm_size" if "initrd_high" is missing
To boot Linux, we should prevent Initramdisk and FDT from going too
high.
Currently, boot_relocate_fdt() checks "fdt_high" environment first,
and then falls back to getenv_bootm_mapsize() + getenv_bootm_low()
if "fdt_high" is missing.
On the other hand, boot_ramdisk_high() only checks "initrd_high" to
get the address limit for the Initramdisk. We also want to let this
case fall back to getenv_bootm_mapsize() + getenv_bootm_low().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:36 +0000 (20:39 +0530)]
dm: core: Add a new api to get indexed device address
Add new api to get device address based on index.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Jagan Teki <jteki@openedev.com>
[Rebased on master]
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 5 Jan 2016 08:14:26 +0000 (13:44 +0530)]
power: pmic.h: Drop include <spi.h>
include/power/pmic.h never used any generic spi code
from include/spi.h, but this has been added in below commit.
"dm: pmic: add implementation of driver model pmic uclass"
(sha1:
4d9057e82be11a862db411c4867e859fe0d4ca2a)
Adding functionalities in include/spi.h will trigger a build
issue as this been added used in include/power/pmic.h
Build issue on trats2 with adding BIT macro on spi.h:
----------------------------------------------------
CC lib/asm-offsets.s
In file included from include/power/pmic.h:15:0,
from include/power/max77686_pmic.h:11,
from include/configs/trats2.h:212,
from include/config.h:5,
from include/common.h:18,
from lib/asm-offsets.c:15:
include/spi.h: In function 'spi_w8r8':
include/spi.h:327:2: warning: implicit declaration of function 'BIT' [-Wimplicit-function-declaration]
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Mugunthan V N [Wed, 23 Dec 2015 15:09:49 +0000 (20:39 +0530)]
defconfig: am437x_sk_evm: enable spi driver model
enable spi driver model for am437x_sk_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:48 +0000 (20:39 +0530)]
arm: dts: am4372: add qspi register maps for memory map
Add qspi memory map address to device tree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:47 +0000 (20:39 +0530)]
am43xx_evm: qspi: do not define DM_SPI and DM_SPI_FLASH for spl
Since OMAP's spl doesn't support DM currently, do not define
DM_SPI and DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:46 +0000 (20:39 +0530)]
defconfig: dra74_evm: enable spi driver model
enable spi driver model for dra74_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:45 +0000 (20:39 +0530)]
defconfig: dra72_evm: enable spi driver model
enable mmc driver model for dra72_evm as ti_qspi supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:44 +0000 (20:39 +0530)]
arm: dts: dra72-evm: add spi-flash comaptible for flash
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:43 +0000 (20:39 +0530)]
arm: dts: dra7-evm: add spi-flash comaptible for flash
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:42 +0000 (20:39 +0530)]
arm: dts: am437x-gp-evm: add spi-flash comaptible for flash
In U-Boot most flashes uses "spi-flash" as compatible to bind the
device to flash driver, so adding "spi-flash" compatible to
m25p80 node.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:41 +0000 (20:39 +0530)]
arm: dts: dra7: add qspi register maps for memory map and control module
Add qspi memory map and control module register maps to device tree.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:40 +0000 (20:39 +0530)]
drivers: spi: ti_qspi: convert driver to adopt device driver model
adopt ti_qspi driver to device driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:39 +0000 (20:39 +0530)]
dts: dra7: add spi alias for qspi
add spi alias for qspi so that spi probes the device and driver
successfully.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:38 +0000 (20:39 +0530)]
dra7xx_evm: qspi: do not define DM_SPI and DM_SPI_FLASH for spl
Since OMAP's spl doesn't support DM currently, do not define DM_SPI and
DM_SPI_FLASH for spl build.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:37 +0000 (20:39 +0530)]
spi: Add support for dual and quad mode
spi bus can support dual and quad wire data transfers for tx and
rx. So defining dual and quad modes for both tx and rx. Also add
support to parse bus width used for spi tx and rx transfers.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:35 +0000 (20:39 +0530)]
drivers: spi: ti_qspi: prepare driver for DM conversion
Prepare driver for DM conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:34 +0000 (20:39 +0530)]
drivers: spi:ti_qspi: change ti_qspi_slave to ti_qspi_priv for driver model conversion
Changing the ti_qspi_priv structure and its instance names from
to priv for driver mode conversion.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Mugunthan V N [Wed, 23 Dec 2015 15:09:33 +0000 (20:39 +0530)]
drivers: spi: ti_qspi: do not hard code chip select for memory map configuration
To enable memory map in dra7xx, specific chip select must be
written to control module register. But this hard coded to chip
select 1, fixing it by writing the specific chip select value to
control module register.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 17:25:50 +0000 (22:55 +0530)]
spi: Add SPI_TX_DUAL mode
Added SPI_TX_DUAL mode flag.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 16:38:40 +0000 (22:08 +0530)]
sf: Make IO modes at last in read modes
SLOW, FAST, DUAL, DUAL_IO, QUAD, QUAD_IO changed order to
SLOW, FAST, DUAL, QUAD, DUAL_IO, QUAD_IO
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 29 Dec 2015 06:42:30 +0000 (12:12 +0530)]
spi: Minor cleanup
- Add comments on mode_rx
- Tab space's
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 16:54:08 +0000 (22:24 +0530)]
spi: Use BIT macro
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 10:21:06 +0000 (15:51 +0530)]
spi: Fix bit assignment with flags
Fixed bit assignment with flags members on spi_slave{}
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 28 Dec 2015 16:53:14 +0000 (22:23 +0530)]
spi: Move flags macro's to spi_slave{} members
This patch moves flags macro's to respective member
position on spi_slave{}, for better readabilty and
finding the respective member macro's easily.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:54:24 +0000 (15:24 +0530)]
spi: Rename op_mode_rx to mode_rx
Since spi rx mode macro's are renamed to simple and
meaninfull, this patch will rename the respective
structure members.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:45:41 +0000 (15:15 +0530)]
spi: Rename SPI_OPM_RX_* to SPI_RX_*
SPI_OPM_RX_AS - SPI_RX_SLOW
SPI_OPM_RX_AF - SPI_RX_FAST
SPI_OPM_RX_DOUT - SPI_RX_DUAL
SPI_OPM_RX_QOF - SPI_RX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:31:23 +0000 (15:01 +0530)]
spi: Remove SPI_OPM_RX_DIO|QIOF
SPI_OPM_RX_DIO and SPI_OPM_RX_QIOF are rx IO
commands/opmodes for dual and quad. Usually IO
operation's are referred to flash protocol rather
with spi controller protocol, these are still present
in flash side for the usage of spi-nor controllers.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 09:23:59 +0000 (14:53 +0530)]
spi: Remove SPI_OPM_RX_EXTN
SPI_OPM_RX_EXTN is a combination of all rx opmode's
and spi driver shall use any one of the rx mode at
a time not the combination and it is true in case of
flash where spi_flash_table mention combination of
supported read opmodes so-that the required one
will pick based on the rx mode from spi driver.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Wed, 16 Dec 2015 08:18:08 +0000 (13:48 +0530)]
sf: Write quad bit along with read status
While setting quad bit on spansion, macronix code
is writing only particular quad bit this may give
wrong functionality with other register bits,
So this patch fix the issue where it with write
previous read reg status along particular quad bit.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 15 Dec 2015 07:12:02 +0000 (12:42 +0530)]
sf: Read back and check once macronix quad bit set
One macronix quad bit set using SR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Tue, 15 Dec 2015 06:58:39 +0000 (12:28 +0530)]
sf: Read back and check once spansion quad bit set
One spansion quad bit set using CR, it's good to
read back and check the written bit and also if
it's already been set check for the bit and return.
Cc: Vignesh R <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 12:45:39 +0000 (18:15 +0530)]
sf: Fix quad bit set for micron devices
Setting up quad bit for micron devices need to do the
same way as other flash devices like spansion, winbond
etc does using enhanced volatile config register so this
patch adds this support instead of printing "QEB is volatile"
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Peter Pan <peterpandong@micron.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 12:42:04 +0000 (18:12 +0530)]
sf: Use BIT macro
Used BIT macro like 1 << nr as BIT(nr) where nr is 0...n
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 12:33:54 +0000 (18:03 +0530)]
sf: Minor cleanup
- Tab space
- Place all read commands at one place.
- Re-arrange write commands.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 03:32:06 +0000 (09:02 +0530)]
sf: Remove spi_flash_remove
Use direct call to device_remove instead of exctra
spi_flash_remove defination.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sun, 13 Dec 2015 17:40:33 +0000 (23:10 +0530)]
sf: Rename bank_end to bar_end in read_bar
bar_end gives more meaningfull compared to bank_end and
spi_flash_write_bar uses bar_end so replaced bank_end with
bar_end in spi_flash_read_bar
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sun, 13 Dec 2015 17:34:46 +0000 (23:04 +0530)]
sf: Rename spi_flash_set_* functions
Since quad_mode functions are local to spi flash core,
rename them to a meaningful and readable names.
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sun, 13 Dec 2015 16:20:26 +0000 (21:50 +0530)]
sf: Move spi_read_cmds_array locally
Since spi_read_cmds_array is used locally in
spi_flash_scan, so move array to locally used
function instead of defining global array.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sun, 13 Dec 2015 14:42:45 +0000 (20:12 +0530)]
spi: Rename SPI_TX_BP|QPP to SPI_TX_BYTE|QUAD
Since SPI_TX_* are spi_slave{} members so use spi protocol
notation instead spi flash programming, like
SPI_TX_BP => SPI_TX_BYTE
SPI_TX_QPP => SPI_TX_QUAD
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sun, 13 Dec 2015 14:40:33 +0000 (20:10 +0530)]
spi: Use mode instead of op_mode_tx
Used mode member from spi_slave{} instead of op_mode_tx.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Mon, 14 Dec 2015 06:45:17 +0000 (12:15 +0530)]
spi: make mode visible to both dm and non-dm
Couldn't find the exact reason to define 'mode' for dm,
probably it is not using in non-dm drivers but it need
to visible both dm and non-dm as mode data is getting
dereferred in spi flash core ie common to both.
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Jagan Teki [Sat, 12 Dec 2015 06:21:57 +0000 (11:51 +0530)]
sf: Get spi locally from spi_flash
For better code readabilty, get the spi pointer from
spi_flash{} locally and use it instead of direct
dereferring spi pinter as flash->spi->*
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Nathan Rossi [Thu, 7 Jan 2016 17:00:48 +0000 (03:00 +1000)]
arm: socfpga: Enable SPL_DM_SEQ_ALIAS for all SOCFPGA configs
This feature is required in SPL to enable support for loading from SPI
flash.
Also clean up the #define in socfpga_common.h.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin-Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Thu, 7 Jan 2016 17:00:47 +0000 (03:00 +1000)]
arm: mvebu: Select SPL_DM_SEQ_ALIAS
Select SPL_DM_SEQ_ALIAS which is required for certain uclasses,
specifically SPI Flash.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Thu, 7 Jan 2016 17:00:46 +0000 (03:00 +1000)]
arm: zynq: Enable SPL_DM_SEQ_ALIAS for all Zynq configs
This feature is required in SPL to enable support for loading from SPI
flash when the device is booted from QSPI.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Nathan Rossi [Thu, 7 Jan 2016 17:00:45 +0000 (03:00 +1000)]
spl: dm: Add SPL_DM_SEQ_ALIAS config option
The Device Model sequence alias feature is required by some Uclasses.
Instead of disabling the feature for all SPL targets allow it to be
configured.
The config option is disabled by default to reduce code size for targets
that are not interested or do not require this feature.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tom Rini [Tue, 12 Jan 2016 23:12:42 +0000 (18:12 -0500)]
Merge git://git.denx.de/u-boot-dm
Tom Rini [Tue, 8 Dec 2015 03:26:34 +0000 (22:26 -0500)]
sandbox: eth-raw-os.c: Ensure that our interface name is not too long
Coverity notes that we do not ensure when we copy ifname we still have
space left to ensure NULL termination. As cannot control the size of
ifr_name we must make sure that our argument will not overflow the
buffer.
Reported-by: Coverity (CID 131094)
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stefan Roese [Mon, 14 Dec 2015 15:18:15 +0000 (16:18 +0100)]
dm: core: Add option to configure an offset for the address translation
Some platforms need to ability to configure an offset to the standard
addresses extracted from the device-tree. This patch allows this by
adding a function to DM to configure this offset (if needed).
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Fixed space before tab:
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Mon, 14 Dec 2015 04:37:00 +0000 (21:37 -0700)]
rockchip: Use the debug UART on rk3036
Rather than using a new debug UART implementation, use the standard one
provided by U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Simon Glass [Mon, 14 Dec 2015 04:36:59 +0000 (21:36 -0700)]
dm: ns16550: Allow the driver to be omitted if requested
Allow the ns16550 debug UART to be used without the full driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Simon Glass [Mon, 14 Dec 2015 04:36:58 +0000 (21:36 -0700)]
dm: serial: Allow the UART driver to be dropped from the image
In very very space-constrained devices even the full UART driver is too
large. In this case the debug UART can still be used in some cases.
Add options to enable the UART driver in SPL and U-Boot proper. Enable both
options by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Simon Glass [Sun, 29 Nov 2015 20:18:11 +0000 (13:18 -0700)]
dm: net: usb: Convert mcs7830 driver to support driver model
Adjust this driver to support driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 29 Nov 2015 20:18:10 +0000 (13:18 -0700)]
dm: net: usb: Refactor mcs7830 driver ready for DM conversion
Remove stamp data and create common functions for the main Ethernet
operations. This will make it easier to convert this driver to support
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 29 Nov 2015 20:18:09 +0000 (13:18 -0700)]
pci: Tidy up comments in pci_bind_bus_devices()
The current comments are confusing. We don't actually bind a generic device
when the device tree has no information. We try to scan available PCI
drivers. Update the comments to reflect this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:18:08 +0000 (13:18 -0700)]
dm: Convert PCI MMC over to use DM PCI API
At present pci_mmc_init() does not correctly use the PCI function since the
list it passes is not terminated. The array size passed to pci_mmc_init() is
actually not used correctly. Fix this and adjust the pci_mmc_init() to scan
all available MMC devices.
Adjust this code to use the new driver model PCI API.
This should move over to the new MMC uclass at some point.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:18:07 +0000 (13:18 -0700)]
dm: usb: Convert echi-pci to use new DM PCI API
Convert this driver to use the new driver model PCI API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Simon Glass [Sun, 29 Nov 2015 20:18:06 +0000 (13:18 -0700)]
dm: ahci: Convert to use new DM PCI API
Convert this driver to use the new driver model PCI API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:18:05 +0000 (13:18 -0700)]
dm: pci: Switch to DM API for PCI address mapping
We should use the new address mapping functions unless we are in
compatibility mode. Disable the old functions by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:18:04 +0000 (13:18 -0700)]
dm: net: Convert rtl8169 to use DM PCI API
Update this driver to use the proper driver-model PCI API functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 29 Nov 2015 20:18:03 +0000 (13:18 -0700)]
dm: pci: Add driver model API functions for address mapping
At present the PCI address map functions use the old API. Add new functions
for this so that drivers can be converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:18:02 +0000 (13:18 -0700)]
dm: test: Convert PCI tests to use the DM PCI API
Update these tests to use driver model API functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass [Sun, 29 Nov 2015 20:18:01 +0000 (13:18 -0700)]
dm: tegra: net: Convert tegra boards to driver model for Ethernet
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Simon Glass [Sun, 29 Nov 2015 20:18:00 +0000 (13:18 -0700)]
dm: pci: Drop the old version of pci_find_class()
Move this function into the compatibility file so that it is not available
by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:59 +0000 (13:17 -0700)]
dm: pci: Drop the old version of pci_find_device/s()
Move these functions into the compatibility file so that they are not
available by default.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:58 +0000 (13:17 -0700)]
dm: x86: pci: Adjust bios_run_on_x86() to use the DM PCI API
This function should take a struct udevice rather than pci_dev_t. Update it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:57 +0000 (13:17 -0700)]
dm: pci: video: Convert video and pci_rom to use DM PCI API
Adjust these files to use the driver-model PCI API instead of the legacy
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:56 +0000 (13:17 -0700)]
dm: Convert bios_interrupts to use DM PCI API
Adjust this code to use driver model for devices where possible. Since
existing users have not been converted the old code must remain.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:55 +0000 (13:17 -0700)]
dm: x86: ivybridge: Convert graphics init to use DM PCI API
Use the driver-model PCI functions here where possible. For now we have to
search for the device with pci_bus_find_bdf() but at some point we can put
this in a proper driver and avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:54 +0000 (13:17 -0700)]
dm: serial: Convert ns16550 driver to use driver model PCI API
Use the driver model version of the function to find the BAR. This updates
the fdtdec function, of which ns16550 is the only user.
The fdtdec_get_pci_bdf() function is dropped for several reasons:
- with driver model we should use 'struct udevice *' rather than passing the
device tree offset explicitly
- there are no other users in the tree
- the function parses for information which is already available in the PCI
device structure (specifically struct pci_child_platdata which is available
at dev_get_parent_platdata(dev)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:53 +0000 (13:17 -0700)]
dm: pci: Add a function to read a PCI BAR
Add a driver-model function for reading the PCI BAR from a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:52 +0000 (13:17 -0700)]
dm: pci: Add a driver-model version of pci_find_class()
Add a function which scans the driver model device information rather
than scanning the PCI bus again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:51 +0000 (13:17 -0700)]
dm: pci: scsi: Use driver-model PCI API
Adjust the SCSI command to use driver model for its PCI interface.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:50 +0000 (13:17 -0700)]
dm: pci: Add a driver-model version of pci_find_device()
Add a function which scans the driver model device information rather
than scanning the PCI bus again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:49 +0000 (13:17 -0700)]
dm: pci: Use driver model PCI API in auto-config
At present we are using legacy functions even in the auto-configuration code
used by driver model. Add a new pci_auto.c version which uses the correct
API.
Create a new pci_internal.h header to hold functions that are used within
the PCI subsystem, but are not exported to other drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:48 +0000 (13:17 -0700)]
dm: pci: Add a dm_ prefix to pci_bus_find_bdf()
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_bus_find_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:47 +0000 (13:17 -0700)]
dm: pci: Add a dm_ prefix to pci_get_bdf()
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Simon Glass [Sun, 29 Nov 2015 20:17:46 +0000 (13:17 -0700)]
dm: pci: Mark legacy files as such
We don't want people changing the legacy PCI files while migration is in
progress. Update the file headers to indicate that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Masahiro Yamada [Fri, 8 Jan 2016 16:51:16 +0000 (01:51 +0900)]
ARM: uniphier: fix recommended board setting in document
The mem_is_flash() in arch/arm/mach-uniphier/micro-support_card.c
writes/reads the tail of each NOR flash bank to check if the device
really resides there.
If CS1_SPLIT were enabled, the support card would always require two
NOR flash devices to be inserted for the correct NOR detection.
This is not probably what we want.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 8 Jan 2016 16:51:15 +0000 (01:51 +0900)]
ARM: uniphier: add dump command for DDR Multi PHY registers
The ProXstream2/PH1-LD6b is integrated with a new IP for DDR PHY
which is not register-compatible with the former SoCs.
Add a new command to support the register dump of this IP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Masahiro Yamada [Fri, 8 Jan 2016 16:51:14 +0000 (01:51 +0900)]
ARM: uniphier: add DRAM init code for ProXstream2/PH1-LD6b
As mentioned in the log of commit
019df879a93e2 (ARM: uniphier: add
ProXstream2 and PH1-LD6b support), the DRAM init code was missing
for a long time. Finally, here it is. SPL works now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>