Stefan Richter [Mon, 16 Aug 2010 19:58:03 +0000 (21:58 +0200)]
firewire: sbp2: fix memory leak in sbp2_cancel_orbs or at send error
When an ORB was canceled (Command ORB i.e. SCSI request timed out, or
Management ORB timed out), or there was a send error in the initial
transaction, we missed to drop one of the ORB's references and thus
leaked memory.
Background:
In total, we hold 3 references to each Operation Request Block:
- 1 during sbp2_scsi_queuecommand() or sbp2_send_management_orb()
respectively,
- 1 for the duration of the write transaction to the ORB_Pointer or
Management_Agent register of the target,
- 1 for as long as the ORB stays within the lu->orb_list, until
the ORB is unlinked from the list and the orb->callback was
executed.
The latter one of these 3 references is finished
- normally by sbp2_status_write() when the target wrote status
for a pending ORB,
- or by sbp2_cancel_orbs() in case of an ORB time-out,
- or by complete_transaction() in case of a send error.
Of them, the latter two lacked the kref_put.
Add the missing kref_put()s. Add comments to the gets and puts of
references for transaction callbacks and ORB callbacks so that it is
easier to see what is supposed to happen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Julia Lawall [Thu, 5 Aug 2010 20:20:09 +0000 (22:20 +0200)]
ieee1394: Adjust confusing if indentation
Indent the branch of an if.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Mon, 2 Aug 2010 07:33:25 +0000 (09:33 +0200)]
Merge firewire branches to be released post v2.6.35
Conflicts:
drivers/firewire/core-card.c
drivers/firewire/core-cdev.c
and forgotten #include <linux/time.h> in drivers/firewire/ohci.c
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Sun, 1 Aug 2010 10:23:14 +0000 (12:23 +0200)]
firewire: core: add forgotten dummy driver methods, remove unused ones
There is an at least theoretic race condition in which .start_iso etc.
could still be called between when the dummy driver is bound to the card
and when the children devices are being shut down. Add dummy_start_iso
and friends.
On the other hand, .enable, .set_config_rom, .read_csr, write_csr do not
need to be implemented by the dummy driver, as commented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Linus Torvalds [Sun, 1 Aug 2010 22:11:14 +0000 (15:11 -0700)]
Linux 2.6.35
Trond Myklebust [Sun, 1 Aug 2010 17:40:40 +0000 (13:40 -0400)]
NFS: Fix a typo in include/linux/nfs_fs.h
nfs_commit_inode() needs to be defined irrespectively of whether or not
we are supporting NFSv3 and NFSv4.
Allow the compiler to optimise away code in the NFSv2-only case by
converting it into an inlined stub function.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 31 Jul 2010 02:02:51 +0000 (19:02 -0700)]
Merge master.kernel.org:/home/rmk/linux-2.6-arm
* master.kernel.org:/home/rmk/linux-2.6-arm:
cyber2000fb: fix console in truecolor modes
cyber2000fb: fix machine hang on module load
SA1111: Eliminate use after free
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
ARM: 6271/1: Introduce *_relaxed() I/O accessors
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
ARM: 6270/1: clean files in arch/arm/boot/compressed/
ARM: Fix csum_partial_copy_from_user()
Linus Torvalds [Sat, 31 Jul 2010 02:02:21 +0000 (19:02 -0700)]
Merge branch 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure that writepage respects the nonblock flag
NFS: kswapd must not block in nfs_release_page
nfs: include space for the NUL in root path
Linus Torvalds [Sat, 31 Jul 2010 02:01:11 +0000 (19:01 -0700)]
Merge branch 'drm-fixes' of git://git./linux/kernel/git/airlied/drm-2.6
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/edid: Fix the HDTV hack sync adjustment
drm/radeon/kms: fix radeon mid power profile reporting
Hugh Dickins [Fri, 30 Jul 2010 17:58:26 +0000 (10:58 -0700)]
mm: fix ia64 crash when gcore reads gate area
Debian's ia64 autobuilders have been seeing kernel freeze or reboot
when running the gdb testsuite (Debian bug 588574): dannf bisected to
2.6.32
62eede62dafb4a6633eae7ffbeb34c60dba5e7b1 "mm: ZERO_PAGE without
PTE_SPECIAL"; and reproduced it with gdb's gcore on a simple target.
I'd missed updating the gate_vma handling in __get_user_pages(): that
happens to use vm_normal_page() (nowadays failing on the zero page),
yet reported success even when it failed to get a page - boom when
access_process_vm() tried to copy that to its intermediate buffer.
Fix this, resisting cleanups: in particular, leave it for now reporting
success when not asked to get any pages - very probably safe to change,
but let's not risk it without testing exposure.
Why did ia64 crash with 16kB pages, but succeed with 64kB pages?
Because setup_gate() pads each 64kB of its gate area with zero pages.
Reported-by: Andreas Barth <aba@not.so.argh.org>
Bisected-by: dann frazier <dannf@debian.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: dann frazier <dannf@dannf.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Fri, 30 Jul 2010 14:25:19 +0000 (15:25 +0100)]
CIFS: Remove __exit mark from cifs_exit_dns_resolver()
Remove the __exit mark from cifs_exit_dns_resolver() as it's called by the
module init routine in case of error, and so may have been discarded during
linkage.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ondrej Zary [Thu, 29 Jul 2010 20:40:54 +0000 (22:40 +0200)]
cyber2000fb: fix console in truecolor modes
Return value was not set to 0 in setcolreg() with truecolor modes. This causes
fb_set_cmap() to abort after first color, resulting in blank palette - and
blank console in 24bpp and 32bpp modes.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ondrej Zary [Thu, 29 Jul 2010 20:32:20 +0000 (22:32 +0200)]
cyber2000fb: fix machine hang on module load
I was testing two CyberPro 2000 based PCI cards on x86 and the machine always
hanged completely when the cyber2000fb module was loaded. It seems that the
card hangs when some registers are accessed too quickly after writing RAMDAC
control register. With this patch, both card work.
Add delay after RAMDAC control register write to prevent hangs on module load.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Julia Lawall [Fri, 30 Jul 2010 15:17:28 +0000 (17:17 +0200)]
SA1111: Eliminate use after free
__sa1111_remove always frees its argument, so the subsequent reference to
sachip->saved_state represents a use after free. __sa1111_remove does not
appear to use the saved_state field, so the patch simply frees it first.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
__sa1111_remove(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King [Thu, 29 Jul 2010 14:58:59 +0000 (15:58 +0100)]
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards. Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Gary King [Thu, 29 Jul 2010 16:37:20 +0000 (17:37 +0100)]
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
smp_processor_id() must not be called from a preemptible context (this
is checked by CONFIG_DEBUG_PREEMPT). kmap_high_l1_vipt() was doing so.
This lead to a problem where the wrong per_cpu kmap_high_l1_vipt_depth
could be incremented, causing a BUG_ON(*depth <= 0); in
kunmap_high_l1_vipt().
The solution is to move the call to smp_processor_id() after the call
to preempt_disable().
Originally by: Andrew Howe <ahowe@nvidia.com>
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Nicolas Pitre <nico.as.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Trond Myklebust [Fri, 30 Jul 2010 19:31:57 +0000 (15:31 -0400)]
NFS: Ensure that writepage respects the nonblock flag
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Trond Myklebust [Fri, 30 Jul 2010 19:31:54 +0000 (15:31 -0400)]
NFS: kswapd must not block in nfs_release_page
See https://bugzilla.kernel.org/show_bug.cgi?id=16056
If other processes are blocked waiting for kswapd to free up some memory so
that they can make progress, then we cannot allow kswapd to block on those
processes.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@kernel.org
Dan Carpenter [Tue, 13 Jul 2010 11:34:59 +0000 (13:34 +0200)]
nfs: include space for the NUL in root path
In root_nfs_name() it does the following:
if (strlen(buf) + strlen(cp) > NFS_MAXPATHLEN) {
printk(KERN_ERR "Root-NFS: Pathname for remote directory too long.\n");
return -1;
}
sprintf(nfs_export_path, buf, cp);
In the original code if (strlen(buf) + strlen(cp) == NFS_MAXPATHLEN)
then the sprintf() would lead to an overflow. Generally the rest of the
code assumes that the path can have NFS_MAXPATHLEN (1024) characters and
a NUL terminator so the fix is to add space to the nfs_export_path[]
buffer.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Linus Torvalds [Thu, 29 Jul 2010 22:23:28 +0000 (15:23 -0700)]
Merge branch 'for-linus' of git://git390.marist.edu/linux-2.6
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] etr: fix clock synchronization race
[S390] Fix IRQ tracing in case of PER
Linus Torvalds [Thu, 29 Jul 2010 22:21:44 +0000 (15:21 -0700)]
Merge git://git./linux/kernel/git/wim/linux-2.6-watchdog
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog:
watchdog: update MAINTAINERS entry
Linus Torvalds [Thu, 29 Jul 2010 22:21:07 +0000 (15:21 -0700)]
Merge branch 'fix/hda' of git://git./linux/kernel/git/tiwai/sound-2.6
* 'fix/hda' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add a PC-beep workaround for ASUS P5-V
ALSA: hda - Assume PC-beep as default for Realtek
ALSA: hda - Don't register beep input device when no beep is available
ALSA: hda - Fix pin-detection of Nvidia HDMI
David Howells [Thu, 29 Jul 2010 11:45:55 +0000 (12:45 +0100)]
CRED: Fix __task_cred()'s lockdep check and banner comment
Fix __task_cred()'s lockdep check by removing the following validation
condition:
lockdep_tasklist_lock_is_held()
as commit_creds() does not take the tasklist_lock, and nor do most of the
functions that call it, so this check is pointless and it can prevent
detection of the RCU lock not being held if the tasklist_lock is held.
Instead, add the following validation condition:
task->exit_state >= 0
to permit the access if the target task is dead and therefore unable to change
its own credentials.
Fix __task_cred()'s comment to:
(1) discard the bit that says that the caller must prevent the target task
from being deleted. That shouldn't need saying.
(2) Add a comment indicating the result of __task_cred() should not be passed
directly to get_cred(), but rather than get_task_cred() should be used
instead.
Also put a note into the documentation to enforce this point there too.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells [Thu, 29 Jul 2010 11:45:49 +0000 (12:45 +0100)]
CRED: Fix get_task_cred() and task_state() to not resurrect dead credentials
It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.
What happens is that get_task_cred() can race with commit_creds():
TASK_1 TASK_2 RCU_CLEANER
-->get_task_cred(TASK_2)
rcu_read_lock()
__cred = __task_cred(TASK_2)
-->commit_creds()
old_cred = TASK_2->real_cred
TASK_2->real_cred = ...
put_cred(old_cred)
call_rcu(old_cred)
[__cred->usage == 0]
get_cred(__cred)
[__cred->usage == 1]
rcu_read_unlock()
-->put_cred_rcu()
[__cred->usage == 1]
panic()
However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.
If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.
We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.
Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:
kernel BUG at kernel/cred.c:168!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/kernel/mm/ksm/run
CPU 0
Pid: 2436, comm: master Not tainted 2.6.33.3-85.fc13.x86_64 #1 0HR330/OptiPlex
745
RIP: 0010:[<
ffffffff81069881>] [<
ffffffff81069881>] __put_cred+0xc/0x45
RSP: 0018:
ffff88019e7e9eb8 EFLAGS:
00010202
RAX:
0000000000000001 RBX:
ffff880161514480 RCX:
00000000ffffffff
RDX:
00000000ffffffff RSI:
ffff880140c690c0 RDI:
ffff880140c690c0
RBP:
ffff88019e7e9eb8 R08:
00000000000000d0 R09:
0000000000000000
R10:
0000000000000001 R11:
0000000000000040 R12:
ffff880140c690c0
R13:
ffff88019e77aea0 R14:
00007fff336b0a5c R15:
0000000000000001
FS:
00007f12f50d97c0(0000) GS:
ffff880007400000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0:
0000000080050033
CR2:
00007f8f461bc000 CR3:
00000001b26ce000 CR4:
00000000000006f0
DR0:
0000000000000000 DR1:
0000000000000000 DR2:
0000000000000000
DR3:
0000000000000000 DR6:
00000000ffff0ff0 DR7:
0000000000000400
Process master (pid: 2436, threadinfo
ffff88019e7e8000, task
ffff88019e77aea0)
Stack:
ffff88019e7e9ec8 ffffffff810698cd ffff88019e7e9ef8 ffffffff81069b45
<0>
ffff880161514180 ffff880161514480 ffff880161514180 0000000000000000
<0>
ffff88019e7e9f28 ffffffff8106aace 0000000000000001 0000000000000246
Call Trace:
[<
ffffffff810698cd>] put_cred+0x13/0x15
[<
ffffffff81069b45>] commit_creds+0x16b/0x175
[<
ffffffff8106aace>] set_current_groups+0x47/0x4e
[<
ffffffff8106ac89>] sys_setgroups+0xf6/0x105
[<
ffffffff81009b02>] system_call_fastpath+0x16/0x1b
Code: 48 8d 71 ff e8 7e 4e 15 00 85 c0 78 0b 8b 75 ec 48 89 df e8 ef 4a 15 00
48 83 c4 18 5b c9 c3 55 8b 07 8b 07 48 89 e5 85 c0 74 04 <0f> 0b eb fe 65 48 8b
04 25 00 cc 00 00 48 3b b8 58 04 00 00 75
RIP [<
ffffffff81069881>] __put_cred+0xc/0x45
RSP <
ffff88019e7e9eb8>
---[ end trace
df391256a100ebdd ]---
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stefan Richter [Thu, 29 Jul 2010 16:19:22 +0000 (18:19 +0200)]
firewire: add isochronous multichannel reception
This adds the DMA context programming and userspace ABI for multichannel
reception, i.e. for listening on multiple channel numbers by means of a
single DMA context.
The use case is reception of more streams than there are IR DMA units
offered by the link layer. This is already implemented by the older
ohci1394 + ieee1394 + raw1394 stack. And as discussed recently on
linux1394-devel, this feature is occasionally used in practice.
The big drawbacks of this mode are that buffer layout and interrupt
generation necessarily differ from single-channel reception: Headers
and trailers are not stripped from packets, packets are not aligned with
buffer chunks, interrupts are per buffer chunk, not per packet.
These drawbacks also cause a rather hefty code footprint to support this
rarely used OHCI-1394 feature. (367 lines added, among them 94 lines of
added userspace ABI documentation.)
This implementation enforces that a multichannel reception context may
only listen to channels to which no single-channel context on the same
link layer is presently listening to. OHCI-1394 would allow to overlay
single-channel contexts by the multi-channel context, but this would be
a departure from the present first-come-first-served policy of IR
context creation.
The implementation is heavily based on an earlier one by Jay Fenlason.
Thanks Jay.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 29 Jul 2010 07:31:56 +0000 (09:31 +0200)]
firewire: core: small clarifications in core-cdev
Make a note on the seemingly unused linux/sched.h.
Rename an irritatingly named variable.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Wed, 28 Jul 2010 21:49:45 +0000 (23:49 +0200)]
firewire: core: remove unused code
ioctl_create_iso_context enforces ctx->header_size >= 4.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Wed, 28 Jul 2010 13:50:00 +0000 (15:50 +0200)]
firewire: ohci: release channel in error path
firewire-ohci keeps book of which isochronous channels are occupied by
IR DMA contexts, so that there cannot be more than one context listening
to a certain channel.
If IR context creation failed due to an out-of-memory condition, this
bookkeeping leaked a channel.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Tue, 27 Jul 2010 11:20:33 +0000 (13:20 +0200)]
firewire: ohci: use memory barriers to order descriptor updates
When we append to a DMA program, we need to ensure that the order in
which initialization of the new descriptors and update of the
branch_address of the old tail descriptor, as seen by the PCI device,
happen as intended.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Wim Van Sebroeck [Thu, 29 Jul 2010 18:02:51 +0000 (18:02 +0000)]
watchdog: update MAINTAINERS entry
Add Mailing-list and website to watchdog MAINTAINERS entry.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Takashi Iwai [Thu, 29 Jul 2010 13:30:02 +0000 (15:30 +0200)]
ALSA: hda - Add a PC-beep workaround for ASUS P5-V
ASUS P5-V provides a SSID that unexpectedly matches with the value
compilant with Realtek's specification. Thus the driver interprets
it badly, resulting in non-working PC beep.
This patch adds a white-list for such a case; a white-list of known
devices with working PC beep.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Russell King [Thu, 29 Jul 2010 10:38:05 +0000 (11:38 +0100)]
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
The ioread/iowrite accessors also need barriers as they're used in
place of readl/writel et.al. in portable drivers. Create __iormb()
and __iowmb() which are conditionally defined to be barriers dependent
on ARM_DMA_MEM_BUFFERABLE, and always use these macros in the accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Wed, 28 Jul 2010 21:01:55 +0000 (22:01 +0100)]
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
When the coherent DMA buffers are mapped as Normal Non-cacheable
(ARM_DMA_MEM_BUFFERABLE enabled), buffer accesses are no longer ordered
with Device memory accesses causing failures in device drivers that do
not use the mandatory memory barriers before starting a DMA transfer.
LKML discussions led to the conclusion that such barriers have to be
added to the I/O accessors:
http://thread.gmane.org/gmane.linux.kernel/683509/focus=686153
http://thread.gmane.org/gmane.linux.ide/46414
http://thread.gmane.org/gmane.linux.kernel.cross-arch/5250
This patch introduces a wmb() barrier to the write*() I/O accessors to
handle the situations where Normal Non-cacheable writes are still in the
processor (or L2 cache controller) write buffer before a DMA transfer
command is issued. For the read*() accessors, a rmb() is introduced
after the I/O to avoid speculative loads where the driver polls for a
DMA transfer ready bit.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Wed, 28 Jul 2010 21:01:25 +0000 (22:01 +0100)]
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors. Since the mandatory barriers may do an L2 cache
sync, this patch avoids a recursive call into l2x0_cache_sync() via the
write*() accessors and wmb() and a call into l2x0_cache_sync() with the
l2x0_lock held.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Catalin Marinas [Wed, 28 Jul 2010 21:00:54 +0000 (22:00 +0100)]
ARM: 6271/1: Introduce *_relaxed() I/O accessors
This patch introduces readl*_relaxed()/write*_relaxed() as the main I/O
accessors (when __mem_pci is defined). The standard read*()/write*()
macros are now based on the relaxed accessors.
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rabin Vincent [Thu, 29 Jul 2010 11:13:18 +0000 (12:13 +0100)]
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
Don't use writeb() in uncompress.h, to avoid the following build errors
when the "Add barriers to the I/O accessors" series is applied. Use
__raw_writeb() instead.
arch/arm/boot/compressed/misc.o: In function `putc':
arch/arm/mach-ux500/include/mach/uncompress.h:41:
undefined reference to `outer_cache'
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Magnus Damm [Wed, 28 Jul 2010 04:46:21 +0000 (05:46 +0100)]
ARM: 6270/1: clean files in arch/arm/boot/compressed/
Update the compressed boot Makefile for ARM to
remove files during clean.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adam Jackson [Tue, 27 Jul 2010 21:40:32 +0000 (07:40 +1000)]
drm/edid: Fix the HDTV hack sync adjustment
We're adjusting horizontal timings only here, moving vsync was just a
slavish translation of a typo in the X server.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel J Blueman [Wed, 28 Jul 2010 11:25:58 +0000 (12:25 +0100)]
drm/radeon/kms: fix radeon mid power profile reporting
Fix incorrectly reporting 'default' power profile, when it is set to 'mid'.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Linus Torvalds [Thu, 29 Jul 2010 03:01:26 +0000 (20:01 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jwessel/linux-2.6-kgdb
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
x86,kgdb: Fix hw breakpoint regression
Linus Torvalds [Thu, 29 Jul 2010 03:00:42 +0000 (20:00 -0700)]
Merge git://git./linux/kernel/git/jejb/scsi-rc-fixes-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
[SCSI] zfcp: Update status read mempool
[SCSI] zfcp: Do not wait for SBALs on stopped queue
[SCSI] zfcp: Fix check whether unchained ct_els is possible
[SCSI] ipr: fix resource path display and formatting
Linus Torvalds [Thu, 29 Jul 2010 02:59:55 +0000 (19:59 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/lrg/voltage-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
Andre Osterhues [Tue, 13 Jul 2010 20:59:17 +0000 (15:59 -0500)]
ecryptfs: Bugfix for error related to ecryptfs_hash_buckets
The function ecryptfs_uid_hash wrongly assumes that the
second parameter to hash_long() is the number of hash
buckets instead of the number of hash bits.
This patch fixes that and renames the variable
ecryptfs_hash_buckets to ecryptfs_hash_bits to make it
clearer.
Fixes: CVE-2010-2492
Signed-off-by: Andre Osterhues <aosterhues@escrypt.com>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jason Wessel [Thu, 29 Jul 2010 00:10:30 +0000 (19:10 -0500)]
x86,kgdb: Fix hw breakpoint regression
HW breakpoints events stopped working correctly with kgdb
as a result of commit:
018cbffe6819f6f8db20a0a3acd9bab9bfd667e4
(Merge commit 'v2.6.33' into perf/core).
The regression occurred because the behavior changed for setting
NOTIFY_STOP as the return value to the die notifier if the breakpoint
was known to the HW breakpoint API. Because kgdb is using the HW
breakpoint API to register HW breakpoints slots, it must also now
implement the overflow_handler call back else kgdb does not get to see
the events from the die notifier.
The kgdb_ll_trap function will be changed to be general purpose code
which can allow an easy way to implement the hw_breakpoint API
overflow call back.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dongdong Deng <dongdong.deng@windriver.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Linus Torvalds [Wed, 28 Jul 2010 18:10:53 +0000 (11:10 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/sage/ceph-client
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: use complete_all and wake_up_all
ceph: Correct obvious typo of Kconfig variable "CRYPTO_AES"
ceph: fix dentry lease release
ceph: fix leak of dentry in ceph_init_dentry() error path
ceph: fix pg_mapping leak on pg_temp updates
ceph: fix d_release dop for snapdir, snapped dentries
ceph: avoid dcache readdir for snapdir
Steven Whitehouse [Wed, 28 Jul 2010 16:56:23 +0000 (17:56 +0100)]
GFS2: Use kmalloc when possible for ->readdir()
If we don't need a huge amount of memory in ->readdir() then
we can use kmalloc rather than vmalloc to allocate it. This
should cut down on the greater overheads associated with
vmalloc for smaller directories.
We may be able to eliminate vmalloc entirely at some stage,
but this is easy to do right away.
Also using GFP_NOFS to avoid any issues wrt to deleting inodes
while under a glock, and suggestion from Linus to factor out
the alloc/dealloc.
I've given this a test with a variety of different sized
directories and it seems to work ok.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Wed, 28 Jul 2010 15:43:36 +0000 (17:43 +0200)]
ALSA: hda - Assume PC-beep as default for Realtek
Enable PC-beep as default for hardwares that aren't compliant with the
SSID value Realtek requires. In such a case, better to enable the beep
to avoid a regression.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 28 Jul 2010 15:37:16 +0000 (17:37 +0200)]
ALSA: hda - Don't register beep input device when no beep is available
We check now the availability of PC beep and skip the build of beep
mixers, but the driver still registers the input device. This should
be checked as well.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sekhar Nori [Mon, 12 Jul 2010 12:26:21 +0000 (17:56 +0530)]
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
Per the da850/omap-l138 Beta EVM SOM schematic, the
DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Anuj Aggarwal [Mon, 12 Jul 2010 12:24:06 +0000 (17:54 +0530)]
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.
The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).
Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Takashi Iwai [Wed, 28 Jul 2010 12:21:55 +0000 (14:21 +0200)]
ALSA: hda - Fix pin-detection of Nvidia HDMI
The behavior of Nvidia HDMI codec regarding the pin-detection unsol events
is based on the old HD-audio spec, i.e. PD bit indicates only the update
and doesn't show the current state. Since the current code assumes the
new behavior, the pin-detection doesn't work relialby with these h/w.
This patch adds a flag for indicating the old spec, and fixes the issue
by checking the pin-detection explicitly for such hardware.
Tested-by: Wei Ni <wni@nvidia.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Linus Torvalds [Tue, 27 Jul 2010 21:32:59 +0000 (14:32 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/ericvh/v9fs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
9p: Pass the correct end of buffer to p9stat_read
Jon Povey [Tue, 27 Jul 2010 20:18:06 +0000 (13:18 -0700)]
gpio: fix spurious printk when freeing a gpio
When freeing a gpio that has not been exported, gpio_unexport() prints a
debug message when it should just fall through silently.
Example spurious message:
gpio_unexport: gpio0 status -22
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Uwe Kleine-K?nig <u.kleine-koenig@pengutronix.de>
Cc: Gregory Bean <gbean@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Anton Vorontsov [Tue, 27 Jul 2010 20:18:05 +0000 (13:18 -0700)]
edac: mpc85xx: fix coldplug/hotplug module autoloading
The MPC85xx EDAC driver is missing module device aliases, so the driver
won't load automatically on boot. This patch fixes the issue by adding
proper MODULE_DEVICE_TABLE() macros.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Dave Jiang <djiang@mvista.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rudolf Marek [Tue, 27 Jul 2010 20:18:02 +0000 (13:18 -0700)]
drivers/rtc/rtc-rx8581.c: fix setdatetime
Fix the logic while writing new date/time to the chip. The driver
incorrectly wrote back register values to different registers and even
with wrong mask. The patch adds clearing of the VLF register, which
should be cleared if all date/time values are set.
Signed-off-by: Rudolf Marek <rudolf.marek@sysgo.com>
Acked-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: Martyn Welch <martyn.welch@gefanuc.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jason Baron [Tue, 27 Jul 2010 20:18:01 +0000 (13:18 -0700)]
dynamic debug: move ddebug_remove_module() down into free_module()
The command
echo "file ec.c +p" >/sys/kernel/debug/dynamic_debug/control
causes an oops.
Move the call to ddebug_remove_module() down into free_module(). In this
way it should be called from all error paths. Currently, we are missing
the remove if the module init routine fails.
Signed-off-by: Jason Baron <jbaron@redhat.com>
Reported-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Cc: <stable@kernel.org> [2.6.32+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Yehuda Sadeh [Tue, 27 Jul 2010 20:11:08 +0000 (13:11 -0700)]
ceph: use complete_all and wake_up_all
This fixes an issue triggered by running concurrent syncs. One of the syncs
would go through while the other would just hang indefinitely. In any case, we
never actually want to wake a single waiter, so the *_all functions should
be used.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
Latchesar Ionkov [Mon, 19 Jul 2010 20:40:03 +0000 (15:40 -0500)]
9p: Pass the correct end of buffer to p9stat_read
Pass the correct end of the buffer to p9stat_read.
Signed-off-by: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
Martin Schwidefsky [Tue, 27 Jul 2010 17:29:38 +0000 (19:29 +0200)]
[S390] etr: fix clock synchronization race
The etr events switch-to-local and sync-check disable the synchronous clock
and schedule a work queue that tries to get the clock back into sync.
If another switch-to-local or sync-check event occurs while the work queue
function etr_work_fn still runs the eacr.es bit and the clock_sync_word can
become inconsistent because check_sync_clock only uses the clock_sync_word
to determine if the clock is in sync or not. The second pass of the
etr_work_fn will reset the eacr.es bit but will leave the clock_sync_word
intact. Fix this race by moving the reset of the eacr.es bit into the
switch-to-local and sync-check functions and by checking the eacr.es bit
as well to decide if the clock needs to be synced.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Heiko Carstens [Tue, 27 Jul 2010 17:29:37 +0000 (19:29 +0200)]
[S390] Fix IRQ tracing in case of PER
In case user space is single stepped (PER) the program check handler
claims too early that IRQs are enabled on the return path.
Subsequent checks will notice that the IRQ mask in the PSW and
what lockdep thinks the IRQ mask should be do not correlate and
therefore will print a warning to the console and disable lockdep.
Fix this by doing all the work within the correct context.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Anton Blanchard [Tue, 13 Jul 2010 04:59:29 +0000 (14:59 +1000)]
[SCSI] ibmvscsi: Fix oops when an interrupt is pending during probe
A driver needs to be ready to take an interrupt as soon as it registers
an interrupt handler. I noticed the following oops when testing kdump:
ipr: IBM Power RAID SCSI Device Driver version: 2.5.0 (February 11, 2010)
ibmvscsi
30000002: SRP_VERSION: 16.a
ibmvscsi
30000002: SRP_VERSION: 16.a
Unable to handle kernel paging request for data at address 0x00000000
...
pc:
c000000004085e34: .tasklet_action+0xf4/0x1dc
...
c000000004086fe4 .__do_softirq+0x16c/0x2c0
c00000000403138c .call_do_softirq+0x14/0x24
c00000000400ee14 .do_softirq+0xa0/0x104
c00000000408690c .irq_exit+0x70/0xd0
c00000000400f190 .do_IRQ+0x214/0x2a8
c000000004004804 hardware_interrupt_entry+0x1c/0x98
--- Exception: 501 (Hardware Interrupt) at
c00000000400c544 .raw_local_irq_restore+0x48/0x54
c00000000465d2a8 ._raw_spin_unlock_irqrestore+0x74/0xa0
c0000000040e7f00 .__setup_irq+0x2ec/0x3f0
c0000000040e8198 .request_threaded_irq+0x194/0x22c
c00000000446d854 .rpavscsi_init_crq_queue+0x284/0x3f0
c00000000446c764 .ibmvscsi_probe+0x688/0x710
c00000000402903c .vio_bus_probe+0x37c/0x3e4
c000000004403f10 .driver_probe_device+0xec/0x1b8
c000000004404088 .__driver_attach+0xac/0xf4
c000000004403184 .bus_for_each_dev+0x98/0x104
c000000004403c98 .driver_attach+0x40/0x60
c0000000044026f0 .bus_add_driver+0x154/0x324
c0000000044045d0 .driver_register+0xe8/0x1ac
c00000000402b2a8 .vio_register_driver+0x54/0x74
c000000004933ea4 .ibmvscsi_module_init+0x80/0xc0
c000000004009834 .do_one_initcall+0x98/0x1d8
c0000000049005b4 .kernel_init+0x27c/0x33c
c000000004031550 .kernel_thread+0x54/0x70
srp_task needs to be setup before request_irq. The patch below fixes the oops.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Linus Torvalds [Tue, 27 Jul 2010 16:23:39 +0000 (09:23 -0700)]
Merge branch 'urgent' of git://git./linux/kernel/git/paulus/perf
* 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/perf:
perf, powerpc: Use perf_sample_data_init() for the FSL code
Linus Torvalds [Tue, 27 Jul 2010 16:22:55 +0000 (09:22 -0700)]
Merge git://git.infradead.org/users/cbou/battery-2.6.35
* git://git.infradead.org/users/cbou/battery-2.6.35:
ds2782_battery: Rename get_current to fix build failure / name conflict
Linus Torvalds [Tue, 27 Jul 2010 16:21:00 +0000 (09:21 -0700)]
Merge git://git./linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
s2io: fixing DBG_PRINT() macro
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
net: dev_forward_skb should call nf_reset
net sched: fix race in mirred device removal
tun: avoid BUG, dump packet on GSO errors
bonding: set device in RLB ARP packet handler
wimax/i2400m: Add PID & VID for Intel WiMAX 6250
ipv6: Don't add routes to ipv6 disabled interfaces.
net: Fix skb_copy_expand() handling of ->csum_start
net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
macvtap: Limit packet queue length
ixgbe/igb: catch invalid VF settings
bnx2x: Advance a module version
bnx2x: Protect statistics ramrod and sequence number
bnx2x: Protect a SM state change
wireless: use netif_rx_ni in ieee80211_send_layer2_update
Peter Zijlstra [Fri, 9 Jul 2010 08:21:21 +0000 (10:21 +0200)]
perf, powerpc: Use perf_sample_data_init() for the FSL code
We should use perf_sample_data_init() to initialize struct
perf_sample_data. As explained in the description of commit
dc1d628a
("perf: Provide generic perf_sample_data initialization"), it is
possible for userspace to get the kernel to dereference data.raw,
so if it is not initialized, that means that unprivileged userspace
can possibly oops the kernel. Using perf_sample_data_init makes sure
it gets initialized to NULL.
This conversion should have been included in commit
dc1d628a, but it
got missed.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Axel Lin [Mon, 26 Jul 2010 02:41:58 +0000 (10:41 +0800)]
wm8350-regulator: fix wm8350_register_regulator error handling
In the case of platform_device_add() fail, we should call
platform_device_put() instead of platform_device_del()
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Axel Lin [Mon, 26 Jul 2010 07:34:14 +0000 (15:34 +0800)]
ab3100: fix off-by-one value range checking for voltage selector
We use voltage selector as an array index for typ_voltages.
Thus the valid range for voltage selector should be 0..voltages_len-1.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: increment program version
Since version 0.3 from Kristian's repository, there should actually be
no change in functionality except for the x86-64 fix. Nevertheless,
make it distinct from the original nosy-dump --- just in case and also
because of potential future changes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: remove unused code
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: use linux/firewire-constants.h
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: break up a deeply nested function
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: make some symbols static or const
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: change to kernel coding style
This changes only
- whitespace
- C99 initializers
- comment style
- order of #includes
- if { } else { } bracing
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: work around segfault in decode_fcp
If I run "nosy-dump --view=transaction" with my camcorder on battery
instead of mains, it segfaults very quickly because of !t->request.
Perhaps this is because of increased likelyhood of incomplete
transactions (ack_busy when host writes to camcorder's FCP_Request)
and a bug deeper in nosy-dump's transaction housekeeping. This is a
quick workaround to get me going.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: nosy-dump: fix it on x86-64
Replace 'unsigned long' and the (unaffected) 'unsigned int' by uint32_t
if they represent quadlets.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:58:05 +0000 (11:58 +0200)]
tools/firewire: add userspace front-end of nosy
This adds nosy-dump, the userspace part of nosy, the IEEE 1394 traffic
sniffer for Texas Instruments PCILynx/ PCILynx2 based cards. Author is
Kristian Høgsberg.
The files added here are taken from
git://anongit.freedesktop.org/~krh/nosy commit
ee29be97 (2009-11-10)
with the following changes by Stefan Richter:
- Parts pertaining to the kernel module removed from Makefile.
- dist target removed from the Makefile.
- Mentioned nosy-dump in the Kconfig help to nosy's kernel component.
- Add copyright notice to nosy-dump.c. This is a duplicate of the
respective notice in the kernel component nosy.c except for a time
span of 2002 - 2006, according to Kristian's git log.
"git shortlog decode-fcp.c list.h nosy-dump.[ch]" from nosy's git
repository:
Jonathan Woithe (1):
Save logs on Ctrl-C
Kristian Høgsberg (11):
Pull over nosy from mercurial repo.
Remove some fields from default view, add logging feature.
Use infinite time out for poll(), mark more detail fields.
Fix byte ordering macro.
Add decoding of iso data and lock packets.
Add flag to indicate data length field.
Add cycle start packet decoding, add --iso and --cycle-start flags.
Distinguish between phy-packets and 0-length iso data.
Fix transaction and stats view.
Add simple AV/C decoder.
Don't break down on big payloads.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Stefan Richter [Thu, 22 Jul 2010 17:50:32 +0000 (19:50 +0200)]
firewire: nosy: note ioctls in ioctl-number.txt
These are the ioctls for the special-purpose misc device /dev/nosy, the
interface to the IEEE 1394 packet sniffer/ protocol analyzer driver.
Currently only the numbers 00...02 are in use; let's block a few more
for unforeseen use cases.
Cc: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: use generic printk macros
Replace home-grown printk wrapper macros by ones from kernel.h and
device.h.
Also raise the log level in set_phy_reg() from debug to error because
these are really error conditions. Could even be WARN_ON. Lower the
log level in the device probe and driver shutdown from notice to info.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: endianess fixes and annotations
1.) The DMA programs (struct pcl) are PCI-endian = little endian data
(except for the 3rd quadlet in a PCL which the controller does not
touch). Annotate them as such.
Fix all accesses of the PCL to work with big endian CPUs also. Not
actually tested, I only have a little endian PC to test with. This
includes replacement of a bitfield struct pcl_status by open-coded
shift and mask operations.
2.) The two __attribute__ ((packed)) at struct pcl are not really
required since it consists of u32/__le32 only, i.e. there will be no
padding with or without the attribute.
3.) The received IEEE 1394 data are byteswapped by the controller from
IEEE 1394 endian = big endian to PCI endian = little endian because the
PCL_BIGENDIAN control bit is set. Therefore annotate the DMA buffer as
a __le32 array.
Fix the one access of the DMA buffer (the check of the transaction code
of link packets) to work with big endian CPUs. Also fix the two
accesses of the client bounce buffer (the reading of packet length).
4.) Add a comment to the userspace ABI header that all of the data gets
out as little endian data, except for the timestamp which is CPU endian.
(We could make it little endian too, but why? Vice versa, an ioctl
could be added to dump packet data in big endian byte order...)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: annotate __user pointers and __iomem pointers
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: fix device shutdown with active client
Fix race between nosy_open() and remove_card() by replacing the
unprotected array of card pointers by a mutex-protected list of cards.
Make card instances reference-counted and let each client hold a
reference.
Notify clients about card removal via POLLHUP in poll()'s events
bitmap; also let read() fail with errno=ENODEV if the card was removed
and everything in the buffer was read.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: handle errors in device probe
and add a missing pci_disable_device() to device shutdown.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: fix IRQ handler for card ejection
Untested, I don't have a PCILynx CardBus card.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: unroll some simple functions
nosy_start/stop_snoop() and nosy_add/remove_client() are simple enough
to be inlined into their callers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: use flagless variants of spinlock accessors
nosy_start/stop_snoop() are always only called by the ioctl method, i.e.
with IRQs enabled. packet_handler() and bus_reset_handler() are always
only called by the IRQ handler. Hence neither one needs to track IRQ
flags.
To underline the call context of packet_handler() and
bus_reset_handler(), rename these functions to *_irq_handler().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: fix list corruption by NOSY_IOC_STOP
nosy_stop_snoop() would blow up the second time it was called without
nosy_start_snoop() in between.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Thu, 22 Jul 2010 09:56:38 +0000 (11:56 +0200)]
firewire: nosy: convert to unlocked ioctl
The required serialization of NOSY_IOC_START and NOSY_IOC_STOP is
already provided by the client_list_lock.
NOSY_IOC_FILTER does not really require serialization since accesses
to tcode_mask are atomic on any sane CPU architecture. Nevertheless,
make it explicit that we want this to be atomic by means of
client_list_lock (which also surrounds the other tcode_mask access in
the IRQ handler). While we are at it, change the type of tcode_mask to
u32 for consistency with the user API.
NOSY_IOC_GET_STATS does not require serialization against itself. But
there is a bug here regarding concurrent updates of the two counters
by the IRQ handler. Fix it by taking the client_list_lock in this ioctl
too.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Tue, 27 Jul 2010 08:28:30 +0000 (10:28 +0200)]
firewire: nosy: misc cleanups
Extend copyright note to 2007, c.f. Kristian's git log.
Includes:
- replace some <asm/*.h> by <linux/*.h>
- add required indirectly included <linux/spinlock.h>
- order alphabetically
Coding style related changes:
- change to utf8
- normalize whitespace
- normalize comment style
- remove usages of __FUNCTION__
- remove an unnecessary cast from void *
Const and static declarations:
- driver_name is not const in pci_driver.name, drop const qualifier
- driver_name can be taken from KBUILD_MODNAME
- the global variable minors[] can and should be static
- constify struct file_operations instance
Data types:
- Remove unused struct member struct packet.code. struct packet is
only used for driver-internal bookkeeping; it does not appear on the
wire or in DMA programs or the userspace ABI. Hence the unused
member .code can be removed without worries.
Preprocessor macros:
- unroll a preprocessor macro that containd a return
- use list_for_each_entry
Printk:
- add missing terminating \n in some format strings
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Stefan Richter [Tue, 27 Jul 2010 08:26:33 +0000 (10:26 +0200)]
firewire: new driver: nosy - IEEE 1394 traffic sniffer
This adds the traffic sniffer driver for Texas Instruments PCILynx/
PCILynx2 based cards. The use cases for nosy are analysis of
nonstandard protocols and as an aid in development of drivers,
applications, or firmwares.
Author of the driver is Kristian Høgsberg. Known contributers are
Jody McIntyre and Jonathan Woithe.
Nosy programs PCILynx chips to operate in promiscuous mode, which is a
feature that is not found in OHCI-1394 controllers. Hence, only special
hardware as mentioned in the Kconfig help text is suitable for nosy.
This is only the kernelspace part of nosy. There is a userspace
interface to it, called nosy-dump, proposed to be added into the tools/
subdirectory of the kernel sources in a subsequent change. Kernelspace
and userspave component of nosy communicate via a 'misc' character
device file called /dev/nosy with a simple ioctl() and read() based
protocol, as described by nosy-user.h.
The files added here are taken from
git://anongit.freedesktop.org/~krh/nosy commit
ee29be97 (2009-11-10)
with the following changes by Stefan Richter:
- Kconfig and Makefile hunks are written from scratch.
- Commented out version printk in nosy.c.
- Included missing <linux/sched.h>, reported by Stephen Rothwell.
"git shortlog nosy{-user.h,.c,.h}" from nosy's git repository:
Jonathan Woithe (2):
Nosy updates for recent kernels
Fix uninitialised memory (needed for 2.6.31 kernel)
Kristian Høgsberg (5):
Pull over nosy from mercurial repo.
Use a misc device instead.
Add simple AV/C decoder.
Don't break down on big payloads.
Set parent device for misc device.
As a low-level IEEE 1394 driver, its files are placed into
drivers/firewire/ although nosy is not part of the firewire driver
stack.
I am aware of the following literature from Texas Instruments about
PCILynx programming:
SCPA020A - PCILynx 1394 to PCI Bus Interface TSB12LV21BPGF
Functional Specification
SLLA023 - Initialization and Asynchronous Programming of the
TSB12LV21A 1394 Device
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Kristian Høgsberg <krh@bitplanet.net>
Linus Torvalds [Mon, 26 Jul 2010 23:02:07 +0000 (16:02 -0700)]
Merge branch 'x86-fixes-for-linus' of git://git./linux/kernel/git/tip/linux-2.6-tip
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Do not try to disable hpet if it hasn't been initialized before
x86, i8259: Only register sysdev if we have a real 8259 PIC
Breno Leitao [Mon, 26 Jul 2010 22:37:30 +0000 (15:37 -0700)]
s2io: fixing DBG_PRINT() macro
Patch
9e39f7c5b311a306977c5471f9e2ce4c456aa038 changed the
DBG_PRINT() macro and the if clause was wrongly changed. It means
that currently all the DBG_PRINT are being printed, flooding the
kernel log buffer with things like:
s2io: eth6: Next block at:
c0000000b9c90000
s2io: eth6: In Neterion Tx routine
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linus Torvalds [Mon, 26 Jul 2010 22:35:53 +0000 (15:35 -0700)]
Merge branch 'fixes' of git://git./linux/kernel/git/davej/cpufreq
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
[CPUFREQ] powernow-k8: Limit Pstate transition latency check
[CPUFREQ] Fix PCC driver error path
[CPUFREQ] fix double freeing in error path of pcc-cpufreq
[CPUFREQ] pcc driver should check for pcch method before calling _OSC
[CPUFREQ] fix memory leak in cpufreq_add_dev
[CPUFREQ] revert "[CPUFREQ] remove rwsem lock from CPUFREQ_GOV_STOP call (second call site)"
Linus Torvalds [Mon, 26 Jul 2010 22:35:04 +0000 (15:35 -0700)]
Merge branch 'upstream' of git://git.linux-mips.org/upstream-linus
* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus:
MIPS: Set io_map_base for several PCI bridges lacking it
MIPS: Alchemy: Define eth platform devices in the correct order
MIPS: BCM63xx: Prevent second enet registration on BCM6338
MIPS: Quit using undefined behavior of ADDU in 64-bit atomic operations.
MIPS: N32: Define getdents64.
MIPS: MTX-1: Fix PCI on the MeshCube and related boards
MIPS: Make init_vdso a subsys_initcall.
MIPS: "Fix" useless 'init_vdso successfully' message.
MIPS: PowerTV: Move register setup to before reading registers.
SOUND: Au1000: Fix section mismatch
VIDEO: Au1100fb: Fix section mismatch
VIDEO: PMAGB-B: Fix section mismatch
VIDEO: PMAG-BA: Fix section mismatch
NET: declance: Fix section mismatches
VIDEO. gbefb: Fix section mismatches.
Jesse Barnes [Mon, 26 Jul 2010 20:51:22 +0000 (13:51 -0700)]
drm/i915: make sure we shut off the panel in eDP configs
Fix error from the last pull request. Making sure we shut the panel off
is more correct and saves power.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David S. Miller [Mon, 26 Jul 2010 20:26:09 +0000 (13:26 -0700)]
Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6
Linus Torvalds [Mon, 26 Jul 2010 20:07:25 +0000 (13:07 -0700)]
Merge git://git./linux/kernel/git/gregkh/driver-core-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
sysfs: allow creating symlinks from untagged to tagged directories
sysfs: sysfs_delete_link handle symlinks from untagged to tagged directories.
sysfs: Don't allow the creation of symlinks we can't remove
Linus Torvalds [Mon, 26 Jul 2010 20:06:39 +0000 (13:06 -0700)]
Merge git://git./linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
USB: musb: tusb6010: fix compile error with n8x0_defconfig
USB: FTDI: Add support for the RT System VX-7 radio programming cable
USB: add quirk for Broadcom BT dongle
USB: usb-storage: fix initializations of urb fields
USB: xhci: Set Mult field in endpoint context correctly.
USB: sisusbvga: Fix for USB 3.0
USB: adds Artisman USB dongle to list of quirky devices
USB: xhci: Set EP0 dequeue ptr after reset of configured device.
USB: Fix USB3.0 Port Speed Downgrade after port reset
USB: xHCI: Fix another bug in link TRB activation change.
USB: option: Add support for AMOI Skypephone S2
USB: New PIDs for Qualcomm gobi 2000 (qcserial)
USB: ftdi_sio: support for Signalyzer tools based on FTDI chips
USB: s3c2410_udc: be aware of connected gadget driver
USB: Expose vendor-specific ACM channel on Nokia 5230
USB: Add PID for Sierra 250U to drivers/usb/serial/sierra.c
USB: option: add support for 1da5:4518
Linus Torvalds [Mon, 26 Jul 2010 20:06:25 +0000 (13:06 -0700)]
Merge git://git./linux/kernel/git/gregkh/tty-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
serial: fix rs485 for atmel_serial on avr32
Linus Torvalds [Mon, 26 Jul 2010 20:04:25 +0000 (13:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/anholt/drm-intel
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: add pipe A force quirks to i915 driver
drm/i915: Fix panel fitting regression since
734b4157
drm/i915: fix deadlock in fb teardown
drm/i915: don't free non-existent compressed llb on ILK+
agp/intel: Use the correct mask to detect i830 aperture size.
drm/i915: disable FBC when more than one pipe is active
drm/i915: Use the correct scanout alignment for fbcon.
drm/i915: make sure eDP panel is turned on
drm/i915: add PANEL_UNLOCK_REGS definition
drm/i915: Make G4X-style PLL search more permissive
drm/i915: Clear any existing dither mode prior to enabling spatial dithering
drm/i915: handle shared framebuffers when flipping
drm/i915: Explosion following OOM in do_execbuffer.
gpu/drm/i915: Add a blacklist to omit modeset on LID open
Borislav Petkov [Thu, 8 Jul 2010 15:55:30 +0000 (17:55 +0200)]
[CPUFREQ] powernow-k8: Limit Pstate transition latency check
The Pstate transition latency check was added for broken F10h BIOSen
which wrongly contain a value of 0 for transition and bus master
latency. Fam11h and later, however, (will) have similar transition
latency so extend that behavior for them too.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>