drm/vc4: hdmi: Reset link on hotplug

During a hotplug cycle (such as a TV going out of suspend, or when the
cable is disconnected and reconnected), the expectation is that the same
state used before the disconnection is reused until the next commit.

However, the HDMI scrambling requires that some flags are set in the
monitor, and those flags are very likely to be reset when the cable has
been disconnected. This will thus result in a blank display, even if the
display pipeline configuration hasn't been modified or is in the exact
same state.

The solution we've had so far is to enable the scrambling-related bits
again on reconnection, but the HDMI 2.0 specification (Section 6.1.3.1 -
Scrambling Control) requires that the scrambling enable bit is set
before sending any scrambled video signal. Using that solution thus
breaks that expectation.

The solution used by i915 is to do a full modeset on the connector so
that we disable the video signal, enable the scrambling bit, and enable
the video signal again.

As such, we took that code and plugged it into vc4. It probably could
have been turned into an helper, but it proved to be difficult for
several reasons:

  * i915 has fairly different structures than simpler KMS drivers such
    as vc4, so doing some code that works with both proved to be
    difficult;

  * Other simpler drivers could reuse some of it (tegra, dw-hdmi), but
    it would still require to move some parameters currently stored in
    private structure that are needed to compute whether the scrambling
    is needed or not, and then inform the driver that it needs to be
    enabled. Some of those parameters are already in core structures
    (drm_display_mode, drm_display_info, bpc), but the output format
    isnt't. Adding it is fairly challenging since unlike the TMDS char
    rate or mode, there's no consensus on what format to pick in
    drivers, so it's not possible to write some generic code that can
    depend on it.

For these reasons, we chose to duplicate the code for now, until someone
else really needs it as well, in which case we will be able to convert
it into a generic helper.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-8-maxime@cerno.tech

drm/vc4: hdmi: Move vc4_hdmi_supports_scrambling() around

We'll need it earlier in the driver, so let's move it next to the other
scrambling-related helpers.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-7-maxime@cerno.tech

drm/vc4: hdmi: Switch to detect_ctx

We'll need the locking context in future patch, so let's convert .detect
to .detect_ctx.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-6-maxime@cerno.tech

drm/vc4: hdmi: Simplify the hotplug handling

Our detect callback has a bunch of operations to perform depending on
the current and last status of the connector, such a setting the CEC
physical address or enabling the scrambling again.

This is currently dealt with a bunch of if / else statetements that make
it fairly difficult to read and extend.

Let's move all that logic to a function of its own.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-5-maxime@cerno.tech

drm/vc4: hdmi: Remove mutex in detect

We recently introduced a new mutex to protect concurrent execution of
ALSA and KMS hooks, and the concurrent access to some of vc4_hdmi
fields.

However, using it in the detect hook was creating a reentrency issue
with CEC code. Indeed, calling cec_s_phys_addr_from_edid from detect
might call the CEC adap_enable hook with the lock held, eventually
resulting in a deadlock.

Since we didn't really need to protect anything at the moment in the CEC
code, the decision was made to ignore the mutex in those CEC hooks,
working around the issue.

However, we can have the same thing happening if we end up triggering a
mode set from the detect callback, for example using
drm_atomic_helper_connector_hdmi_reset_link().

Since we don't really need to protect anything in detect either, let's
just drop the lock in detect, and add it again in CEC.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-4-maxime@cerno.tech

drm/vc4: hdmi: Remove unused argument in vc4_hdmi_supports_scrambling

Even though vc4_hdmi_supports_scrambling takes a mode as an argument, it
never uses it. Let's remove it.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-3-maxime@cerno.tech

drm/vc4: hdmi: Constify drm_display_mode

We don't modify the drm_display_mode pointer we have in the driver in
most places, so let's make them const.

Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20220829134731.213478-2-maxime@cerno.tech

drm/tests: Set also mock plane src_x, src_y, src_w and src_h

We need to set also src_x, src_y, src_w and src_h for the mock plane.
After fix for drm_atomic_helper_damage_iter_init we are using these
when iterating damage_clips.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220823112920.352563-5-jouni.hogander@intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Tested-by: Maíra Canal <mairacanal@riseup.net>

drm: Use original src rect while initializing damage iterator

drm_plane_state->src might be modified by the driver. This is done
e.g. in i915 driver when there is bigger framebuffer than the plane
and there is some offset within framebuffer. I915 driver calculates
separate offset and adjusts src rect coords to be relative to this
offset. Damage clips are still relative to original src coords
provided by user-space.

This patch ensures original coordinates provided by user-space are
used when initiliazing damage iterator.

Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220823112920.352563-2-jouni.hogander@intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>

Revert "drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP"

As reported by Laurent in response to this commit[1], this functionality
should not be implemented using the devicetree, because of this let's
revert this series for now.

This reverts commit c312b0df3b13e4c533743bb2c37fd1bc237368e5.

[1] https://lore.kernel.org/all/20220902153906.31000-2-macroalpha82@gmail.com/

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912113856.817188-3-robert.foss@linaro.org

Revert "dt-bindings: Add byteswap order to chrontel ch7033"

As reported by Laurent in response to this commit[1], this functionality
should not be implemented using the devicetree, because of this let's
revert this series for now.

This reverts commit a4be71430c76eca43679e8485085c230afa84460.

[1] https://lore.kernel.org/all/20220902153906.31000-2-macroalpha82@gmail.com/

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912113856.817188-2-robert.foss@linaro.org

drm/bridge: it6505: use drm_debug_enabled() in it6505_debug_print()

As made mention of in commit 9f0ac028410f ("drm/print: rename drm_debug
to __drm_debug to discourage use"), we shouldn't explicitly refer to
__drm_debug in this context. So, use drm_debug_enabled() instead.

Fixes: b5c84a9edcd4 ("drm/bridge: add it6505 driver")
Signed-off-by: Hamza Mahfooz <someguy@effective-light.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220910224816.15058-1-someguy@effective-light.com

drm/aperture: Fix some kerneldoc comments

Reword some kerneldoc comments for the DRM aperture handling code.

Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905162241.391226-1-thierry.reding@gmail.com

drm/format-helper: Add drm_fb_build_fourcc_list() helper

Add drm_fb_build_fourcc_list() function that builds a list of supported
formats from native and emulated ones. Helpful for all drivers that do
format conversion as part of their plane updates. Update current caller.

v3:
* improve warnings on ignored formats (Sam)
v2:
* use u32 instead of uint32_t (Sam)
* print a warning if output array is too small (Sam)
* comment fixes (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-5-tzimmermann@suse.de

drm/modes: Add initializer macro DRM_MODE_INIT()

The macro DRM_MODE_INIT() initializes an instance of
struct drm_display_mode with typical parameters. Convert simpledrm
and also update the macro DRM_SIMPLE_MODE().

v3:
* fix DRM_MODE_INIT() docs (kernel test robot)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-4-tzimmermann@suse.de

drm/probe-helper: Add drm_crtc_helper_mode_valid_fixed()

Add drm_crtc_helper_mode_valid_fixed(), which validates a given mode
against a display hardware's mode. Convert simpledrm and use it in a
few other drivers with static modes.

v4:
* remove empty line after opening brace
v2:
* rename 'static' and 'hw' to 'fixed' everywhere

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-3-tzimmermann@suse.de

drm/probe-helper: Add drm_connector_helper_get_modes_fixed()

Add drm_connector_helper_get_modes_fixed(), which duplicates a single
display mode for a connector. Convert drivers.

v2:
* rename 'static' and 'hw' to 'fixed' everywhere
* fix typo 'there' to 'their' (Sam)

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-2-tzimmermann@suse.de

drm/vkms: fix variable dereferenced before check warning

Smatch warns:

drivers/gpu/drm/vkms/vkms_plane.c:110 vkms_plane_atomic_update() warn:
 variable dereferenced before check 'fb' (see line 108)

Fix the warning by moving the dereference after the NULL check.

Fixes: 8ba1648567e2 ("drm: vkms: Refactor the plane composer to accept new formats")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908105623.72777-1-harshit.m.mogalapalli@oracle.com

drm/udl: Sync pending URBs at the end of suspend

It's better to perform the sync at the very last of the suspend
instead of the pipe-disable function, so that we can catch all pending
URBs (if any).

While we're at it, drop the error code from udl_sync_pending_urb()
since we basically ignore it; instead, give a clear error message
indicating a problem.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-13-tiwai@suse.de

drm/udl: Don't re-initialize stuff at retrying the URB list allocation

udl_alloc_urb_list() retires the allocation if there is no enough room
left, and it reinitializes the stuff unnecessarily such as the linked
list head and the waitqueue, which could be harmful.  Those should be
outside the retry loop.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-12-tiwai@suse.de

drm/udl: Fix inconsistent urbs.count value during udl_free_urb_list()

In the current design, udl_get_urb() may be called asynchronously
during the driver freeing its URL list via udl_free_urb_list().
The problem is that the sync is determined by comparing the urbs.count
and urbs.available fields, while we clear urbs.count field only once
after udl_free_urb_list() finishes, i.e. during udl_free_urb_list(),
the state becomes inconsistent.

For fixing this inconsistency and also for hardening the locking
scheme, this patch does a slight refactoring of the code around
udl_get_urb() and udl_free_urb_list().  Now urbs.count is updated in
the same spinlock at extracting a URB from the list in
udl_free_url_list().

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-11-tiwai@suse.de

drm/udl: Fix potential URB leaks

A couple of error handlings forgot to process the URB completion.
Those are both with WARN_ON() so should be visible, but we must fix
them in anyway.

Fixes: 7350b2a3fbc6 ("drm/udl: Replace BUG_ON() with WARN_ON()")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-10-tiwai@suse.de

drm/udl: Pass rectangle directly to udl_handle_damage()

Just for some code simplification.

Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/87tu5iauw4.wl-tiwai@suse.de

drm/udl: Drop unneeded alignment

The alignment of damaged area was needed for the original udlfb driver
that tried to trim the superfluous copies between front and backend
buffers and handle data in long int.  It's not the case for udl DRM
driver, hence we can omit the whole unneeded alignment, as well as the
dead code.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-8-tiwai@suse.de

drm/udl: Increase the default URB list size to 20

It seems that the current size (4) for the URB list is too small on
some devices, and it resulted in the occasional stalls.  Increase the
default URB list size to 20 for working around it.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-7-tiwai@suse.de

drm/udl: Suppress error print for -EPROTO at URB completion

The driver may receive -EPROTO at the URB completion when the device
gets disconnected, and it's a normal situation.  Suppress the error
print for that, too.

Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-6-tiwai@suse.de

Revert "drm/udl: Kill pending URBs at suspend and disconnect"

This reverts the recent fix commit
  e25d5954264d ("drm/udl: Kill pending URBs at suspend and disconnect")
as it turned out to lead to potential hangup at a disconnection, and
it doesn't help much for suspend/resume problem, either.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-5-tiwai@suse.de

drm/udl: Enable damage clipping

Call drm_plane_enable_fb_damage_clips() and give userspace a chance
of minimizing the updated display area.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-4-tiwai@suse.de

drm/udl: Add reset_resume

Implement the reset_resume callback of struct usb_driver. Set the
standard channel when called.

Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-3-tiwai@suse.de

drm/udl: Restore display mode on resume

Restore the display mode whne resuming from suspend. Currently, the
display remains dark.

On resume, the CRTC's mode does not change, but the 'active' flag
changes to 'true'. Taking this into account when considering a mode
switch restores the display mode.

The bug is reproducable by using Gnome with udl and observing the
adapter's suspend/resume behavior.

Actually, the whole check added in udl_simple_display_pipe_enable()
about the crtc_state->mode_changed was bogus.  We should drop the
whole check and always apply the mode change in this function.

[ tiwai -- Drop the mode_changed check entirely instead, per Daniel's
  suggestion ]

Fixes: 997d33c35618 ("drm/udl: Inline DPMS code into CRTC enable and disable functions")
Cc: <stable@vger.kernel.org>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908095115.23396-2-tiwai@suse.de

drm/format: Split into more granular test cases

While we have multiple test cases, most of them check multiple
conditions, calling the function that is tested multiple times with
different arguments (with comments that indicate test case boundary).
This usually means that it can be easily converted into multiple test
cases.

Passing output:
============================================================
================= drm_format (18 subtests) =================
[PASSED] drm_format_block_width_invalid
[PASSED] drm_format_block_width_one_plane
[PASSED] drm_format_block_width_two_plane
[PASSED] drm_format_block_width_three_plane
[PASSED] drm_format_block_width_tiled
[PASSED] drm_format_block_height_invalid
[PASSED] drm_format_block_height_one_plane
[PASSED] drm_format_block_height_two_plane
[PASSED] drm_format_block_height_three_plane
[PASSED] drm_format_block_height_tiled
[PASSED] drm_format_min_pitch_invalid
[PASSED] drm_format_min_pitch_one_plane_8bpp
[PASSED] drm_format_min_pitch_one_plane_16bpp
[PASSED] drm_format_min_pitch_one_plane_24bpp
[PASSED] drm_format_min_pitch_one_plane_32bpp
[PASSED] drm_format_min_pitch_two_plane
[PASSED] drm_format_min_pitch_three_plane_8bpp
[PASSED] drm_format_min_pitch_tiled
=================== [PASSED] drm_format ====================
============================================================
Testing complete. Ran 18 tests: passed: 18

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831215608.349269-2-michal.winiarski@intel.com

drm/format: Use appropriate types in expect/assert

drm_format_info_* functions don't return bool, and the info variable is a
pointer.
Expecting non-NULL info will cause the test to crash if it is NULL in
checks that follow (which dereference it).
Use appropriate KUNIT_EXPECT/KUNIT_ASSERT variants.

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831215608.349269-1-michal.winiarski@intel.com

drm/rockchip: dsi: add rk3568 support

Add the compatible and GRF definitions for the RK3568 soc.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906174823.28561-4-macroalpha82@gmail.com

dt-bindings: display: rockchip-dsi: add rk3568 compatible

The rk3568 uses the same dw-mipi-dsi controller as previous Rockchip
SOCs, so add a compatible string for it.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220906174823.28561-2-macroalpha82@gmail.com

drm/rockchip: vop: fix repeated words in comment

Delete the redundant word 'in'.

Signed-off-by: wangjianli <wangjianli@cdjrlc.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908123616.19195-1-wangjianli@cdjrlc.com

drm/tidss: fix repeated words in comments

 Delete the redundant word 'to'.

Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220824130450.41703-1-yuanjilin@cdjrlc.com

drm/omap: dmm_tiler:Remove the print function dev_err()

From the coccinelle check:

./drivers/gpu/drm/omapdrm/omap_dmm_tiler.c
Error:line 817 is redundant because platform_get_irq() already prints an
error

So,remove the unnecessary print function dev_err()

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220810062738.13554-1-ye.xingchen@zte.com.cn

drm/omap: dss: Fix refcount leak bugs

In dss_init_ports() and __dss_uninit_ports(), we should call
of_node_put() for the reference returned by of_graph_get_port_by_id()
in fail path or when it is not used anymore.

Fixes: 09bffa6e5192 ("drm: omap: use common OF graph helpers")
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220722144348.1306569-1-windhl@126.com

drm: omapdrm: dss: replace ternary operator with max()

Fix the following coccicheck warning:

drivers/gpu/drm/omapdrm/dss/dispc.c:2454:21-22: WARNING opportunity for max()

Signed-off-by: Guo Zhengkui <guozhengkui@vivo.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220517050208.121488-1-guozhengkui@vivo.com

drm/sun4i: tv: Include drm_atomic.h

Commit ec491291dc94 ("drm/sun4i: tv: Merge mode_set into atomic_enable")
has introduced a call to drm_atomic_get_new_crtc_state(), but didn't
include drm_atomic.h.

On CONFIG_OF systems, this is fine because drm_atomic.h is included by
drm_of.h through drm_bridge.h. However, whenever CONFIG_OF isn't set, we
end up with a compilation error.

Fixes: ec491291dc94 ("drm/sun4i: tv: Merge mode_set into atomic_enable")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220909093116.4141982-1-maxime@cerno.tech

drm/dp_mst: Avoid deleting payloads for connectors staying enabled

When an MST connector stays enabled during a commit the connector's MST
state needs to be added to the atomic state, but the corresponding MST
payload allocation shouldn't be set for deletion; fix such modesets by
ensuring the above even if the connector was already enabled before the
modeset.

The issue led to the following:
[  761.992923] i915 0000:00:02.0: drm_WARN_ON(payload->delete)
[  761.992949] WARNING: CPU: 6 PID: 1401 at drivers/gpu/drm/display/drm_dp_mst_topology.c:4221 drm_dp_atomic_find_time_slots+0x236/0x280 [drm_display_helper]
[  761.992955] Modules linked in: snd_hda_intel i915 drm_buddy drm_display_helper drm_kms_helper ttm drm snd_hda_codec_hdmi snd_intel_dspcfg snd_hda_codec snd_hwdep snd_hda_core snd_pcm prime_numbers i2c_algo_bit syscopyarea sysfillrect sysimgblt fb_sys_fops x86_pkg_temp_thermal cdc_ether coretemp crct10dif_pclmul usbnet crc32_pclmul mii ghash_clmulni_intel e1000e mei_me ptp i2c_i801 pps_core mei i2c_smbus intel_lpss_pci fuse [last unloaded: drm]
[  761.992986] CPU: 6 PID: 1401 Comm: testdisplay Tainted: G     U             6.0.0-rc4-imre+ #565
[  761.992989] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR5 RVP, BIOS ADLPFWI1.R00.3135.A00.2203251419 03/25/2022
[  761.992990] RIP: 0010:drm_dp_atomic_find_time_slots+0x236/0x280 [drm_display_helper]
[  761.992994] Code: 4c 8b 67 50 4d 85 e4 75 03 4c 8b 27 e8 03 28 4e e1 48 c7 c1 8b 26 2c a0 4c 89 e2 48 c7 c7 a8 26 2c a0 48 89 c6 e8 31 d5 88 e1 <0f> 0b 49 8b 85 d0 00 00 00 4c 89 fa 48 c7 c6 a0 41 2c a0 48 8b 78
[  761.992995] RSP: 0018:ffffc9000177ba60 EFLAGS: 00010286
[  761.992998] RAX: 0000000000000000 RBX: ffff88810d2f1540 RCX: 0000000000000000
[  761.992999] RDX: 0000000000000001 RSI: ffffffff82368a25 RDI: 00000000ffffffff
[  761.993000] RBP: ffff888142299d80 R08: ffff8884adbfdfe8 R09: 00000000ffefffff
[  761.993001] R10: ffff8884a6bfe000 R11: ffff8884ac443c30 R12: ffff888102972f90
[  761.993002] R13: ffff8881163e2cf0 R14: 00000000000003ac R15: ffff88810c501000
[  761.993003] FS:  00007f81e4c459c0(0000) GS:ffff888496500000(0000) knlGS:0000000000000000
[  761.993004] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  761.993005] CR2: 0000555dac962a98 CR3: 0000000123a34006 CR4: 0000000000770ee0
[  761.993006] PKRU: 55555554
[  761.993007] Call Trace:
[  761.993009]  <TASK>
[  761.993012]  intel_dp_mst_compute_config+0x19a/0x350 [i915]
[  761.993090]  intel_atomic_check+0xf37/0x3180 [i915]
[  761.993168]  drm_atomic_check_only+0x5d3/0xa60 [drm]
[  761.993182]  drm_atomic_commit+0x56/0xc0 [drm]
[  761.993192]  ? drm_plane_get_damage_clips.cold+0x1c/0x1c [drm]
[  761.993204]  drm_atomic_helper_set_config+0x78/0xc0 [drm_kms_helper]
[  761.993214]  drm_mode_setcrtc+0x1ed/0x750 [drm]
[  761.993232]  ? drm_mode_getcrtc+0x180/0x180 [drm]
[  761.993241]  drm_ioctl_kernel+0xb5/0x150 [drm]
[  761.993252]  drm_ioctl+0x203/0x3d0 [drm]
[  761.993261]  ? drm_mode_getcrtc+0x180/0x180 [drm]
[  761.993276]  __x64_sys_ioctl+0x8a/0xb0
[  761.993281]  do_syscall_64+0x38/0x90
[  761.993285]  entry_SYSCALL_64_after_hwframe+0x63/0xcd
[  761.993287] RIP: 0033:0x7f81e551aaff
[  761.993288] Code: 00 48 89 44 24 18 31 c0 48 8d 44 24 60 c7 04 24 10 00 00 00 48 89 44 24 08 48 8d 44 24 20 48 89 44 24 10 b8 10 00 00 00 0f 05 <41> 89 c0 3d 00 f0 ff ff 77 1f 48 8b 44 24 18 64 48 2b 04 25 28 00
[  761.993290] RSP: 002b:00007fff4304af10 EFLAGS: 00000246 ORIG_RAX: 0000000000000010
[  761.993292] RAX: ffffffffffffffda RBX: 00007fff4304afa0 RCX: 00007f81e551aaff
[  761.993293] RDX: 00007fff4304afa0 RSI: 00000000c06864a2 RDI: 0000000000000004
[  761.993294] RBP: 00000000c06864a2 R08: 0000000000000000 R09: 0000555dac8a9c68
[  761.993294] R10: 0000000000000000 R11: 0000000000000246 R12: 00000000000008c4
[  761.993295] R13: 0000000000000004 R14: 0000555dac8a9c68 R15: 00007fff4304b098
[  761.993301]  </TASK>

Fixes: 083351e96386 ("drm/display/dp_mst: Fix modeset tracking in drm_dp_atomic_release_vcpi_slots()")
Testcase: igt@testdisplay
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907142542.1681994-1-imre.deak@intel.com

drm/panel-edp: Add Innolux N120ACA-EA1 panel entry

This panel has the same delay timing as N116BCA-EA1 from the same
company, which is also the same as delay_200_500_e80_d50.

Add an entry for it.

Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220908085454.1024167-2-wenst@chromium.org

drm/sun4i: tv: Merge mode_set into atomic_enable

Our mode_set implementation can be merged into our atomic_enable
implementation to simplify things, so let's do this.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-36-459522d653a7@cerno.tech

drm/ssd130x: Replace simple display helpers with the atomic helpers

The simple display pipeline is a set of helpers that can be used by DRM
drivers to avoid dealing with all the needed components and just define
a few functions to operate a simple display device with one full-screen
scanout buffer feeding a single output.

But it is arguable that this provides the correct level of abstraction
for simple drivers, and recently some have been ported from using these
simple display helpers to use the regular atomic helpers instead.

The rationale for this is that the simple display pipeline helpers don't
hide that much of the DRM complexity, while adding an indirection layer
that conflates the concepts of CRTCs and planes. This makes the helpers
less flexible and harder to be reused among different graphics drivers.

Also, for simple drivers, using the full atomic helpers doesn't require
a lot of additional code. So adding a simple display pipeline layer may
not be worth it.

For these reasons, let's follow that trend and make ssd130x a plain DRM
driver that creates its own primary plane, CRTC, enconder and connector.

Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905222759.2597186-1-javierm@redhat.com

drm/gma500: fix repeated words in comments

Delete the redundant word 'for'.

Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Signed-off-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907113927.35305-1-yuanjilin@cdjrlc.com

drm/qxl: fix the suspend/resume issue on qxl device

Details:
Currently, when trying to suspend and resume with qxl device，
there are some error messages after resuming,
eventually caused to black screen and can't be recovered.

The first error message:
[   64.668577][    C3] [drm] driver is in bug mode

This error is due to guest qxl driver
will call qxl_reinit_memslots(qdev) during system resume,
but didn't call qxl_io_reset(qdev) before this,
Then will cause the QXL_IO_MEMSLOT_ADD operation to fail on QEMU,
qxl->guest_bug flag will be set，As a result,
the QXL device can't communicate with guest qxl driver through the IO port.

after fix the first error,can success to resume and login to desktop,
but shortly after that will observe the second error message :
[  353.095343][  T863] qxl 0000:00:02.0: object_init failed for (262144, 0x00000001)
[  353.096660][  T863] [drm:qxl_gem_object_create [qxl]] *ERROR* Failed to allocate GEM object (260852, 1, 4096, -12)
[  353.097277][  T863] [drm:qxl_alloc_ioctl [qxl]] *ERROR* qxl_alloc_ioctl: failed to create gem ret=-12
[  368.197538][  T863] qxl 0000:00:02.0: object_init failed for (3149824, 0x00000001)
[  368.197541][  T863] [drm:qxl_alloc_bo_reserved [qxl]] *ERROR* failed to allocate VRAM BO

The problem is caused by calling qxl_ring_init_hdr(qdev->release_ring)
in qxl_drm_resume() function.
When do QXL_IO_RESET,QEMU will call init_qxl_ram(),
so params like prod,cons,notify_on_cons and notify_on_prod
will be set to default value.
Ring push/pop actions for release_ring can be performed normally.
But call qxl_ring_init_hdr(qdev->release_ring)
will eventually set notify_on_prod to number of QXL_RELEASE_RING_SIZE,
affect the value of notify in qxl_push_free_res() function always be false,
QEMU will no longer send events of QXL_INTERRUPT_DISPLAY to the
guest qxl driver，so qxl_ring_pop() will never been called anymore，
and can't do dma_fence_signal(),result to ttm_bo_wait_ctx(bo, ctx)
always return EBUSY,fail to call qxl_bo_create().

Test scenario:
1) start virtual machine with qemu command "-device qxl-vga"
2) click suspend botton to enter suspend mode
3) resume and observe the error message in kernel logs,screen will be black

Let's fix this by reset io and remove the qxl_ring_init_hdr calling.

Signed-off-by: Zongmin Zhou<zhouzongmin@kylinos.cn>
Suggested-by: Ming Xie<xieming@kylinos.cn>
Link: http://patchwork.freedesktop.org/patch/msgid/20220907094423.93581-1-min_halo@163.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/bochs: fix blanking

VGA_IS1_RC is the color mode register (VGA_IS1_RM the one for monochrome
mode, note C vs. M at the end).  So when using VGA_IS1_RC make sure the
vga device is actually in color mode and set the corresponding bit in the
misc register.

Reproducible when booting VMs in UEFI mode with some edk2 versions (edk2
fix is on the way too).  Doesn't happen in BIOS mode because in that
case the vgabios already flips the bit.

Fixes: 250e743915d4 ("drm/bochs: Add screen blanking support")
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/20220906142957.2763577-1-kraxel@redhat.com

drm/virtio: set fb_modifiers_not_supported

Without this, the drm core advertises LINEAR modifier which is
incorrect.

Also userspace virgl does not support modifiers.  For example, it causes
chrome on ozone/drm to fail with "Failed to create scanout buffer".

Fixes: 2af104290da5 ("drm: introduce fb_modifiers_not_supported flag in mode_config")
Suggested-by: Shao-Chuan Lee <shaochuan@chromium.org>
Signed-off-by: Chia-I Wu <olvaffe@gmail.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20220831190601.1295129-1-olvaffe@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>

drm/sun4i: tv: Add missing reset assertion

The reset line is deasserted at bind, and asserted if we ever encounter an
error there. However, it's never asserted in unbind which will lead to a
resource unbalance.

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-40-459522d653a7@cerno.tech

drm/sun4i: tv: Rename error label

The other error labels in sun4i_tv_bind() are named after the task they
perform (err_disable_clk to call clk_disable_unprepare for example).

However, the err_cleanup_connector is named after the calling site
(drm_connector_init failing) and will actually cleanup the encoder. Let's
rename it to err_cleanup_encoder to be consistent.

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-39-459522d653a7@cerno.tech

drm/sun4i: tv: Remove useless destroy function

Our destroy implementation is just calling the generic helper, so let's
just remove our function and directly use the helper.

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-38-459522d653a7@cerno.tech

drm/sun4i: tv: Remove useless function

The drm_connector_to_sun4i_tv() function isn't used anywhere in the driver,
so let's remove it.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-37-459522d653a7@cerno.tech

drm/sun4i: tv: Convert to atomic hooks

The sun4i TV driver still uses legacy enable and disable hook
implementation. Let's convert to the atomic variants.

Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-35-459522d653a7@cerno.tech

drm/sun4i: tv: Remove unused mode_valid

The mode_valid implementation is pretty much a nop, let's remove it.

Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-34-459522d653a7@cerno.tech

drm/vc4: vec: Fix timings for VEC modes

This commit fixes vertical timings of the VEC (composite output) modes
to accurately represent the 525-line ("NTSC") and 625-line ("PAL") ITU-R
standards.

Previous timings were actually defined as 502 and 601 lines, resulting
in non-standard 62.69 Hz and 52 Hz signals being generated,
respectively.

Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-28-459522d653a7@cerno.tech

drm/vc4: vec: Remove redundant atomic_mode_set

Let's remove the superfluous tv_mode field, which was redundant with the
mode field in struct drm_tv_connector_state.

Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-27-459522d653a7@cerno.tech

drm/vc4: vec: Refactor VEC TV mode setting

Change the mode_set function pointer logic to declarative config0,
config1 and custom_freq fields, to make TV mode setting logic more
concise and uniform.

Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
[Maxime: Fixed != 0 check, added tv_mode variable]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-26-459522d653a7@cerno.tech

drm/vc4: vec: Convert to atomic helpers

The VC4 VEC driver still uses legacy enable and disable hook
implementation. Let's convert to the atomic variants.

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-25-459522d653a7@cerno.tech

drm/vc4: vec: Remove empty mode_fixup

The mode_fixup hooks are deprecated, and the behaviour we implement is the
default one anyway. Let's remove it.

Reviewed-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220728-rpi-analog-tv-properties-v2-24-459522d653a7@cerno.tech

drm/ttm: Remove unnecessary '0' values from ret

The variable ret is assigned in the judgment branch statement, he does
not need to initialize the assignment.

Signed-off-by: Li zeming <zeming@nfschina.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220907032934.4490-1-zeming@nfschina.com
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>

drm/via: Add new condition to via_dma_cleanup()

Pointer dev_priv->mmio, which was checked for NULL at via_do_init_map(),
is passed to via_do_cleanup_map() and is dereferenced there without check.

The patch adds the condition in via_dma_cleanup() which prevents potential NULL
pointer dereference.

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: 22f579c621e2 ("drm: Add via unichrome support")
Signed-off-by: Alisa Khabibrakhmanova <khabibrakhmanova@ispras.ru>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220729090643.240778-1-khabibrakhmanova@ispras.ru

drm/panel-edp: Fix typo in kerneldoc comment (appers=>appears)

Ever since I got the spell-check working in my editor this one has
been bugging me. Fix it.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720162314.1.Ieef5bc3848df40b71605b70bb571d6429e8978de@changeid

drm/scheduler: quieten kernel-doc warnings

Fix kernel-doc warnings in gpu_scheduler.h and sched_main.c.

Quashes these warnings:

include/drm/gpu_scheduler.h:332: warning: missing initial short description on line:
 * struct drm_sched_backend_ops
include/drm/gpu_scheduler.h:412: warning: missing initial short description on line:
 * struct drm_gpu_scheduler
include/drm/gpu_scheduler.h:461: warning: Function parameter or member 'dev' not described in 'drm_gpu_scheduler'

drivers/gpu/drm/scheduler/sched_main.c:201: warning: missing initial short description on line:
 * drm_sched_dependency_optimized
drivers/gpu/drm/scheduler/sched_main.c:995: warning: Function parameter or member 'dev' not described in 'drm_sched_init'

Fixes: 2d33948e4e00 ("drm/scheduler: add documentation")
Fixes: 8ab62eda177b ("drm/sched: Add device pointer to drm_gpu_scheduler")
Fixes: 542cff7893a3 ("drm/sched: Avoid lockdep spalt on killing a processes")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Cc: Nayan Deshmukh <nayan26deshmukh@gmail.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Jiawei Gu <Jiawei.Gu@amd.com>
Cc: dri-devel@lists.freedesktop.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220404213040.12912-1-rdunlap@infradead.org

drm/bridge: anx7625: Set HPD irq detect window to 2ms

Some panels trigger HPD irq due to noise, the HPD debounce
may be 1.8ms, exceeding the default irq detect window, ~1.4ms.
This patch set HPD irq detection window to 2ms to
tolerate the HPD noise.

Signed-off-by: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220903130833.541463-1-xji@analogixsemi.com

drm: vkms: Add support to the RGB565 format

This commit also adds new helper macros to deal with fixed-point
arithmetic.

It was done to improve the precision of the conversion to ARGB16161616
since the "conversion ratio" is not an integer.

V3: Adapt the handlers to the new format introduced in patch 7 V3.
V5: Minor improvements
V6: Minor improvements (Pekka Paalanen)

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-10-igormtorrente@gmail.com

drm: vkms: Adds XRGB_16161616 and ARGB_1616161616 formats

This will be useful to write tests that depends on these formats.

ARGB and XRGB follows the a similar implementation of the former formats.
Just adjusting for 16 bits per channel.

V3: Adapt the handlers to the new format introduced in patch 7 V3.
V5: Minor improvements
    Added le16_to_cpu/cpu_to_le16 to the 16 bits color read/writes.

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-9-igormtorrente@gmail.com

drm: vkms: Supports to the case where primary plane doesn't match the CRTC

We will remove the current assumption that the primary plane has the
same size and position as CRTC and that the primary plane is the
bottom-most in zpos order, or is even enabled. At least as far
as the blending machinery is concerned.

For that we will add CRTC dimension information to `vkms_crtc_state`
and add a opaque black backgound color.

Because now we need to fill the background, we had a loss in
performance with this change. Results running the IGT[1] test
`igt@kms_cursor_crc@pipe-a-cursor-512x512-onscreen` ten times:

|                  Frametime                   |
|:--------------------------------------------:|
|  Implementation |  Previous |   This commit  |
|:---------------:|:---------:|:--------------:|
| frametime range |  5~18 ms  |     10~22 ms   |
|     Average     |  8.47 ms  |     12.32 ms   |

[1] IGT commit id: bc3f6833a12221a46659535dac06ebb312490eb4

V6: Improve the commit description (Pekka Paalanen).
    Update some comments (Pekka Paalanen).
    Remove some fields from `vkms_crtc_state` and move where
    some variables are set (Pekka Paalanen).

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-8-igormtorrente@gmail.com

drm: vkms: Refactor the plane composer to accept new formats

Currently the blend function only accepts XRGB_8888 and ARGB_8888
as a color input.

This patch refactors all the functions related to the plane composition
to overcome this limitation.

The pixels blend is done using the new internal format. And new handlers
are being added to convert a specific format to/from this internal format.

So the blend operation depends on these handlers to convert to this common
format. The blended result, if necessary, is converted to the writeback
buffer format.

This patch introduces three major differences to the blend function.
1 - All the planes are blended at once.
2 - The blend calculus is done as per line instead of per pixel.
3 - It is responsible to calculates the CRC and writing the writeback
buffer(if necessary).

These changes allow us to allocate way less memory in the intermediate
buffer to compute these operations. Because now we don't need to
have the entire intermediate image lines at once, just one line is
enough.

| Memory consumption (output dimensions) |
|:--------------------------------------:|
|       Current      |     This patch    |
|:------------------:|:-----------------:|
|   Width * Heigth   |     2 * Width     |

Beyond memory, we also have a minor performance benefit from all
these changes. Results running the IGT[1] test
`igt@kms_cursor_crc@pipe-a-cursor-512x512-onscreen` ten times:

|                 Frametime                  |
|:------------------------------------------:|
|  Implementation |  Current  |  This commit |
|:---------------:|:---------:|:------------:|
| frametime range |  9~22 ms  |    5~17 ms   |
|     Average     |  11.4 ms  |    7.8 ms    |

[1] IGT commit id: bc3f6833a12221a46659535dac06ebb312490eb4

V2: Improves the performance drastically, by performing the operations
    per-line and not per-pixel(Pekka Paalanen).
    Minor improvements(Pekka Paalanen).
V3: Changes the code to blend the planes all at once. This improves
    performance, memory consumption, and removes much of the weirdness
    of the V2(Pekka Paalanen and me).
    Minor improvements(Pekka Paalanen and me).
V4: Rebase the code and adapt it to the new NUM_OVERLAY_PLANES constant.
V5: Minor checkpatch fixes and the removal of TO-DO item(Melissa Wen).
    Several security/robustness improvents(Pekka Paalanen).
    Removes check_planes_x_bounds function and allows partial
    partly off-screen(Pekka Paalanen).
V6: Fix a mismatch of some variable sizes (Pekka Paalanen).
    Several minor improvements (Pekka Paalanen).

Reviewed-by: Melissa Wen <mwen@igalia.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-7-igormtorrente@gmail.com

drm: vkms: Add fb information to `vkms_writeback_job`

This commit is the groundwork to introduce new formats to the planes and
writeback buffer. As part of it, a new buffer metadata field is added to
`vkms_writeback_job`, this metadata is represented by the `vkms_frame_info`
struct.

Also adds two new function pointers (`line_to_frame_func` and
`frame_to_line_func`) are defined to handle format conversion
from/to internal format.

A new internal format(`struct pixel_argb_u16`) is introduced to deal with
all possible inputs. It consists of 16 bits fields that represent each of
the channels.

These things will allow us, in the future, to have different compositing
and wb format types.

V2: Change the code to get the drm_framebuffer reference and not copy its
    contents (Thomas Zimmermann).
V3: Drop the refcount in the wb code (Thomas Zimmermann).
V5: Add {wb,plane}_format_transform_func to vkms_writeback_job
    and vkms_plane_state (Pekka Paalanen)
V6: Improvements to some struct/struct members names (Pekka Paalanen).
    Splits this patch in two (Pekka Paalanen).
V7: Replace line_to_frame_func and frame_to_line_func typedefs
   with the function signature and void* (Melissa Wen).

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-6-igormtorrente@gmail.com

drm: vkms: get the reference to `drm_framebuffer` instead if coping it

Instead of coping `drm_framebuffer` - which can cause problems -
we just get the reference and add the ref count.

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-5-igormtorrente@gmail.com

drm: drm_atomic_helper: Add a new helper to deal with the writeback connector validation

Add a helper function to validate the connector configuration received in
the encoder atomic_check by the drivers.

So the drivers don't need to do these common validations themselves.

V2: Move the format verification to a new helper at the drm_atomic_helper.c
    (Thomas Zimmermann).
V3: Format check improvements (Leandro Ribeiro).
    Minor improvements(Thomas Zimmermann).
V5: Fix some grammar issues in the commit message (André Almeida).

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-4-igormtorrente@gmail.com

drm: vkms: Rename `vkms_composer` to `vkms_frame_info`

Changes the name of this struct to a more meaningful name.
A name that represents better what this struct is about.

Composer is the code that do the compositing of the planes.
This struct contains information on the frame used in the output
composition. Thus, vkms_frame_info is a better name to represent
this.

V5: Fix a commit message typo(Melissa Wen).
V6: Fix wrong iosys_map_is_null verification at compose_plane
    (Melissa Wen).

Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-3-igormtorrente@gmail.com

drm: vkms: Replace hardcoded value of `vkms_composer.map` to DRM_FORMAT_MAX_PLANES

The `map` vector at `vkms_composer` uses a hardcoded value to define its
size.

If someday the maximum number of planes increases, this hardcoded value
can be a problem.

This value is being replaced with the DRM_FORMAT_MAX_PLANES macro.

Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Igor Torrente <igormtorrente@gmail.com>
Signed-off-by: Melissa Wen <melissa.srw@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905190811.25024-2-igormtorrente@gmail.com

drm/atomic-helper: log EINVAL cause in drm_atomic_helper_async_check()

This can help figure out why the kernel returns EINVAL from
user-space.

v2: add missing newlines

Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220829151451.152114-2-contact@emersion.fr

drm/atomic-helper: print message on driver connector check failure

Sometimes drivers are missing logs when they return EINVAL.
Printing the failure here in common code can help understand where
EINVAL is coming from.

All other atomic_check() calls in this file already have similar
logging.

v2: add missing newlines

Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220829151451.152114-1-contact@emersion.fr

drm: hide unregistered connectors from GETCONNECTOR IOCTL

When registering a connector, the kernel sends a hotplug uevent in
drm_connector_register(). When unregistering a connector, drivers
are expected to send a uevent as well. However, user-space has no way
to figure out that the connector isn't registered anymore: it'll still
be reported in GETCONNECTOR IOCTLs.

The documentation for DRM_CONNECTOR_UNREGISTERED states:

> The connector […] has since been unregistered and removed from
> userspace, or the connector was unregistered before it had a chance
> to be exposed to userspace

Signed-off-by: Simon Ser <contact@emersion.fr>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220801133754.461037-1-contact@emersion.fr

drm/mediatek: dp: Audio support for MT8195

This patch adds audio support to the DP driver for MT8195 with up to 8
channels.

Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-11-rex-bc.chen@mediatek.com

drm/mediatek: dp: Add hpd debounce

From the DP spec 1.4a chapter 3.3, upstream devices should implement
HPD signal de-bouncing on an external connection.
A period of 100ms should be used to detect an HPD connect event.
To cover these cases, HPD de-bounce should be implemented only after
HPD low has been detected for at least 100ms.

Therefore,
1. If HPD is low (which means plugging out) for longer than 100ms:
   we need to do de-bouncing (which means we need to wait for 100ms).
2. If HPD low is for less than 100ms:
   we don't need to care about the de-bouncing.

In this patch, we start a 100ms timer and use a need_debounce boolean
to implement the feature.

Two cases when HPD is high:
1. If the timer is expired (>100ms):
   - need_debounce is true.
   - When HPD high (plugging event comes), need_debounce will be true
     and then we need to do de-bouncing (wait for 100ms).
2. If the timer is not expired (<100ms):
   - need_debounce is false.
   - When HPD high (plugging event comes), need_debounce will be false
     and no need to do de-bouncing.

HPD_______             __________________
          |            |<-  100ms   ->
          |____________|
          <-  100ms   ->

Without HPD de-bouncing, USB-C to HDMI Adapaters will not be detected.

The change has been successfully tested with the following devices:
- Dell Adapter - USB-C to HDMI
- Acer 1in1 HDMI dongle
- Ugreen 1in1 HDMI dongle
- innowatt HDMI + USB3 hub
- Acer 2in1 HDMI dongle
- Apple 3in1 HDMI dongle (A2119)
- J5Create 3in1 HDMI dongle (JAC379)

Tested-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-10-rex-bc.chen@mediatek.com

drm/mediatek: dp: Add MT8195 External DisplayPort support

Add External DisplayPort support to the MT8195 eDP driver.

Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-9-rex-bc.chen@mediatek.com

drm/mediatek: dp: Determine device of next_bridge

It's not necessary to have a next_bridge for DP device, so we add this
patch to judge this.

Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-8-rex-bc.chen@mediatek.com

drm/mediatek: dp: Add multiple calibration data formats support

The calibration data formats of eDP and DP are different. We add
"const struct mtk_dp_efuse_fmt *efuse_fmt" to the device data to
define them.

Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-7-rex-bc.chen@mediatek.com

drm/mediatek: dp: Add multiple smc commands support

The smc commands of eDP and DP are different. We add smc_cmd to the
device data to define them.

Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-6-rex-bc.chen@mediatek.com

drm/mediatek: dp: Add multiple bridge types support

The bridge types of eDP and DP are different. We add device data to
this driver and add bridge_type to the device data to define them.

Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-5-rex-bc.chen@mediatek.com

drm/mediatek: Add MT8195 Embedded DisplayPort driver

This patch adds a embedded displayport driver for the MediaTek mt8195 SoC.

It supports the MT8195, the embedded DisplayPort units. It offers
DisplayPort 1.4 with up to 4 lanes.

The driver creates a child device for the phy. The child device will
never exist without the parent being active. As they are sharing a
register range, the parent passes a regmap pointer to the child so that
both can work with the same register range. The phy driver sets device
data that is read by the parent to get the phy device that can be used
to control the phy properties.

This driver is based on an initial version by
Jitao shi <jitao.shi@mediatek.com>

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Tested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-4-rex-bc.chen@mediatek.com

video/hdmi: Add audio_infoframe packing for DP

Similar to HDMI, DP uses audio infoframes as well which are structured
very similar to the HDMI ones.

This patch adds a helper function to pack the HDMI audio infoframe for
DP, called hdmi_audio_infoframe_pack_for_dp().
hdmi_audio_infoframe_pack_only() is split into two parts. One of them
packs the payload only and can be used for HDMI and DP.

Also constify the frame parameter in hdmi_audio_infoframe_check() as
it is passed to hdmi_audio_infoframe_check_only() which expects a const.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-3-rex-bc.chen@mediatek.com

dt-bindings: mediatek,dp: Add Display Port binding

This controller is present on several mediatek hardware. Currently
mt8195 and mt8395 have this controller without a functional difference,
so only one compatible field is added.

The controller can have two forms, as a normal display port and as an
embedded display port.

Signed-off-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Guillaume Ranquet <granquet@baylibre.com>
Signed-off-by: Bo-Chen Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901044149.16782-2-rex-bc.chen@mediatek.com

drm/bridge: chrontel-ch7033: Add byteswap order setting

Add the option to set the byteswap order in the devicetree. For the
official HDMI DIP for the NTC CHIP the byteswap order needs to be
RGB, however the driver sets it as BGR. With this patch the driver
will remain at BGR unless manually specified via devicetree.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902153906.31000-3-macroalpha82@gmail.com

dt-bindings: Add byteswap order to chrontel ch7033

Update dt-binding documentation to add support for setting byteswap of
chrontel ch7033.

New property name of chrontel,byteswap added to set the byteswap order.
This property is optional.

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220902153906.31000-2-macroalpha82@gmail.com

drm/bridge: ti-sn65dsi86: Implement bridge connector operations for DP

Implement the bridge connector-related .get_edid() and .detect()
operations for full DP mode, and report the related bridge capabilities
and type.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-4-tomi.valkeinen@ideasonboard.com

drm/bridge: ti-sn65dsi86: Support DisplayPort (non-eDP) mode

Despite the SN65DSI86 being an eDP bridge, on some systems its output is
routed to a DisplayPort connector. Enable DisplayPort mode when the next
component in the display pipeline is detected as a DisplayPort
connector, and disable eDP features in that case.

Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reworked to set bridge type based on the next bridge/connector.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
--
Changes since v1/RFC:
 - Rebased on top of "drm/bridge: ti-sn65dsi86: switch to
   devm_drm_of_get_bridge"
 - eDP/DP mode determined from the next bridge connector type.

Changes since v2:
 - Remove setting of Standard DP Scrambler Seed. (It's read-only).
 - Prevent setting DP_EDP_CONFIGURATION_SET in
   ti_sn_bridge_atomic_enable()
 - Use Doug's suggested text for disabling ASSR on DP mode.

Changes since v3:
 - Remove ASSR_CONTROL definition

Changes since v4:
 - Refactor code to configure the DP/eDP scrambler in one place.

Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-3-tomi.valkeinen@ideasonboard.com

drm/bridge: ti-sn65dsi86: Reject modes with too large blanking

The front and back porch registers are 8 bits, and pulse width registers
are 15 bits, so reject any modes with larger periods.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen+renesas@ideasonboard.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220831082653.20449-2-tomi.valkeinen@ideasonboard.com

drm/i915/dp_mst: Fix mst_mgr lookup during atomic check

If an MST connector was disabled in the old state during a commit, the
connector's best_encoder will be NULL, so we can't look up mst_mgr via
it. Do the lookup instead via intel_connector->mst_port which always
points to the primary encoder.

This fixes the following:
[   58.922866] BUG: kernel NULL pointer dereference, address: 0000000000000170
[   58.922867] #PF: supervisor read access in kernel mode
[   58.922868] #PF: error_code(0x0000) - not-present page
[   58.922869] PGD 0 P4D 0
[   58.922870] Oops: 0000 [#1] PREEMPT SMP NOPTI
[   58.922872] CPU: 0 PID: 133 Comm: kworker/0:2 Tainted: G     U             6.0.0-rc3-imre+ #560
[   58.922874] Hardware name: Intel Corporation Alder Lake Client Platform/AlderLake-P DDR5 RVP, BIOS ADLPFWI1.R00.3135.A00.2203251419 03/25/2022
[   58.922874] Workqueue: events output_poll_execute [drm_kms_helper]
[   58.922879] RIP: 0010:intel_dp_mst_atomic_check+0xbb/0x1c0 [i915]
[   58.922955] Code: 5b 7b f6 ff 84 c0 75 41 48 8b 44 24 18 65 48 2b 04 25 28 00 00 00 0f 85 ff 00 00 00 48 8b 45 10 48 8b 93 10 07 00 00 4c 89 e7 <48> 8b b0 70 01 00 00 48 83 c4 20 5b 5d 48 81 c6 f0 0c 00 00 41 5c
[   58.922956] RSP: 0018:ffffc90000633a88 EFLAGS: 00010246
[   58.922957] RAX: 0000000000000000 RBX: ffff888117d19000 RCX: ffff888101893308
[   58.922958] RDX: ffff888122981000 RSI: ffffffff82309ecc RDI: ffff888114da6800
[   58.922959] RBP: ffff8881094bab48 R08: 0000000081917436 R09: 0000000068191743
[   58.922960] R10: 0000000000000001 R11: 0000000000000001 R12: ffff888114da6800
[   58.922960] R13: ffff8881143f8000 R14: 0000000000000000 R15: ffff888119bf2000
[   58.922961] FS:  0000000000000000(0000) GS:ffff888496200000(0000) knlGS:0000000000000000
[   58.922962] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[   58.922962] CR2: 0000000000000170 CR3: 0000000005612004 CR4: 0000000000770ef0
[   58.922963] PKRU: 55555554
[   58.922963] Call Trace:
[   58.922964]  <TASK>
[   58.922966]  drm_atomic_helper_check_modeset+0x3f8/0xc70 [drm_kms_helper]
[   58.922972]  intel_atomic_check+0xb1/0x3180 [i915]
[   58.923059]  ? find_held_lock+0x2b/0x80
[   58.923064]  drm_atomic_check_only+0x5d3/0xa60 [drm]
[   58.923082]  drm_atomic_commit+0x56/0xc0 [drm]
[   58.923097]  ? drm_plane_get_damage_clips.cold+0x1c/0x1c [drm]
[   58.923114]  drm_client_modeset_commit_atomic+0x235/0x280 [drm]
[   58.923132]  drm_client_modeset_commit_locked+0x5b/0x190 [drm]
[   58.923148]  drm_client_modeset_commit+0x24/0x50 [drm]
[   58.923164]  drm_fb_helper_set_par+0xae/0xe0 [drm_kms_helper]
[   58.923171]  drm_fb_helper_hotplug_event+0xd5/0xf0 [drm_kms_helper]
[   58.923178]  output_poll_execute+0xac/0x200 [drm_kms_helper]
[   58.923187]  process_one_work+0x268/0x580
[   58.923190]  ? process_one_work+0x580/0x580
[   58.923191]  worker_thread+0x52/0x3b0
[   58.923193]  ? process_one_work+0x580/0x580
[   58.923195]  kthread+0xf0/0x120
[   58.923196]  ? kthread_complete_and_exit+0x20/0x20
[   58.923198]  ret_from_fork+0x1f/0x30
[   58.923202]  </TASK>

Fixes: ffac9721939d ("drm/display/dp_mst: Don't open code modeset checks for releasing time slots")
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220901161933.1004778-1-imre.deak@intel.com

drm/cmdline-parser: Use assert when needed

Expecting to observe a specific value, when the function responsible for
setting the value has failed will lead to extra noise in test output.
Use assert when the situation calls for it.
Also - very small tidying up around the changed areas (whitespace).

v2: Leave out the locals (drm_connector is huge) (lkp)

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817211236.252091-2-michal.winiarski@intel.com

drm/cmdline-parser: Merge negative tests

Negative tests can be expressed as a single parameterized test case,
which highlights that we're following the same test logic (passing
invalid cmdline and expecting drm_mode_parse_command_line_for_connector
to fail), which improves readability.

v2: s/negative/invalid to be consistent with other testcases in DRM

Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: Maíra Canal <mairacanal@riseup.net>
Signed-off-by: Maíra Canal <mairacanal@riseup.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20220817211236.252091-1-michal.winiarski@intel.com

gpu/drm/bridge/cadence: avoid flush_scheduled_work() usage

Like commit c4f135d643823a86 ("workqueue: Wrap flush_workqueue() using a
macro") says, flush_scheduled_work() is dangerous and will be forbidden.
We are on the way for removing all flush_scheduled_work() callers from
the kernel, and this patch is for removing flush_scheduled_work() call
 from cadence driver.

Since cdns-mhdp8546 driver uses 4 works

  mhdp->modeset_retry_work
  mhdp->hpd_work
  mhdp->hdcp.check_work
  mhdp->hdcp.prop_work

I assume that flush_scheduled_work() in cdns_mhdp_remove() needs to wait
for only these 4 works.

Since mhdp->modeset_retry_work already uses cancel_work_sync(), I assume
that flush_scheduled_work() needs to wait for only 3 works. But I came to
wonder whether mhdp->hdcp.check_work should be flushed or cancelled.

While flush_scheduled_work() waits for completion of works which were
already queued to system_wq, mhdp->hdcp.check_work is a delayed work.
That is, this work won't be queued to system_wq unless timeout expires.

Current code will wait for mhdp->hdcp.check_work only if timeout already
expired. If timeout is not expired yet, flush_scheduled_work() will fail
to cancel mhdp->hdcp.check_work, and cdns_mhdp_hdcp_check_work() which is
triggered by mhdp->hdcp.check_work will schedule hdcp->check_work, which
is too late for flush_scheduled_work() to wait for completion of
cdns_mhdp_hdcp_prop_work().

But since I couldn't get comments on how do we want to handle this race
window [1], this patch chose "do nothing" for mhdp->hdcp.check_work and
mhdp->hdcp.prop_work. That is, I assume that flush_scheduled_work() in
cdns_mhdp_remove() needs to wait for only mhdp->hpd_work work.

Link: https://lkml.kernel.org/r/943273cb-c2ec-24e3-5edb-64eacc6e2d30@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/216591bc-28bb-0453-10bb-59e268dff540@I-love.SAKURA.ne.jp

drm/panfrost: Update io-pgtable API

Convert to io-pgtable's bulk {map,unmap}_pages() APIs, to help the old
single-page interfaces eventually go away. Unmapping heap BOs still
wants to be done a page at a time, but everything else can get the full
benefit of the more efficient interface.

Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Alyssa Rosenzweig <alyssa@collabora.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Steven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/daef7f8c134d989c55636a5790d8c0fcaca1bae3.1661205687.git.robin.murphy@arm.com

MAINTAINERS: Add myself as a reviewer for panel-edp.c

panel-edp changes go through the drm-misc tree (as per the "DRM PANEL
DRIVERS" entry in MAINTAINERS), but ever since splitting panel-edp out
of panel-simple I've been trying to keep a close eye on it. Make that
official by listing me as a reviewer.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220822105340.1.I66a9a5577f9b0af66492ef13c47bc78ed85e5d6b@changeid

drm/bridge: it6505: Fix the order of DP_SET_POWER commands

Send DP_SET_POWER_D3 command to the downstream before stopping DP, so the
suspend process will not be interrupted by the HPD interrupt. Also modify
the order in .atomic_enable callback to make the callbacks symmetric.

Fixes: 46ca7da7f1e8 ("drm/bridge: it6505: Send DPCD SET_POWER to downstream")
Signed-off-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830045756.1655954-1-treapking@chromium.org

drm/bridge: megachips: Fix a null pointer dereference bug

When removing the module we will get the following warning:

[   31.911505] i2c-core: driver [stdp2690-ge-b850v3-fw] unregistered
[   31.912484] general protection fault, probably for non-canonical address 0xdffffc0000000001: 0000 [#1] PREEMPT SMP KASAN PTI
[   31.913338] KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
[   31.915280] RIP: 0010:drm_bridge_remove+0x97/0x130
[   31.921825] Call Trace:
[   31.922533]  stdp4028_ge_b850v3_fw_remove+0x34/0x60 [megachips_stdpxxxx_ge_b850v3_fw]
[   31.923139]  i2c_device_remove+0x181/0x1f0

The two bridges (stdp2690, stdp4028) do not probe at the same time, so
the driver does not call ge_b850v3_resgiter() when probing, causing the
driver to try to remove the object that has not been initialized.

Fix this by checking whether both the bridges are probed.

Fixes: 11632d4aa2b3 ("drm/bridge: megachips: Ensure both bridges are probed before registration")
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220830073450.1897020-1-zheyuma97@gmail.com

drm/dp: add drm_dp_phy_name() for getting DP PHY name

Add a helper for getting the DP PHY name. In the interest of caller
simplicity and to avoid allocations and passing in of buffers, duplicate
the const strings to return. It's a minor penalty to pay for simplicity
in all the call sites.

v2: Rebase, add kernel-doc, ensure non-NULL always

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/b08dc12a7e621a48ec35546d6cd1ed4b1434810d.1660553850.git.jani.nikula@intel.com