net: mvpp2: fix a typo in the header

This cosmetic patch fixes a typo made in a comment in the Marvell PPv2
Ethernet driver header.

Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: Call netif_carrier_off properly in pci_probe

netif_carrier_off() should be called only after register_netdev().

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'cxgb4-vf-link-state'

Arjun Vynipadath says:

====================
cxgb4/cxgb4vf: VF link state support

This series of patches adds support for ndo_set_vf_link_state in
cxgb4 driver.

Patch 1 implements ndo_set_vf_link_state
Patch 2 reverts the existing force_link_up behaviour for cxgb4vf driver.

v2:
- Using reverse christmas tree for variable declaration in Patch 1
- Patch 2 has no change
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: Revert force link up behaviour

Reverting force link up changes since this behaviour can be
achieved using VF link state feature.

Reverts:
commit 0913667ab3ad ("cxgb4vf: Forcefully link up virtual interfaces")

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Add VF Link state support

Use ndo_set_vf_link_state to control the link states associated
with the virtual interfaces.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: Prefix adapter flags with CXGB4VF

Some of these macros were conflicting with global namespace,
hence prefixing them with CXGB4VF.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: Remove unnecessary semicolon

drivers/net/dsa/mt7530.c:649:3-4: Unneeded semicolon
drivers/net/ethernet/cisco/enic/enic_clsf.c:35:2-3: Unneeded semicolon
drivers/net/ethernet/faraday/ftgmac100.c:1640:2-3: Unneeded semicolon
drivers/net/ethernet/mediatek/mtk_eth_soc.c:229:2-3: Unneeded semicolon
drivers/net/usb/sr9700.c:437:2-3: Unneeded semicolon

Remove unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com> for mt7530 and mtk_eth_soc
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'SO_MAX_PACING_RATE-64-bit'

Eric Dumazet says:

====================
net: 64bit support for SO_MAX_PACING_RATE

64bit kernels adopted 64bit type for sk_max_pacing_rate in linux-4.20

We can change how we implement SO_MAX_PACING_RATE socket option
to support 64bit values to/from user space as well.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: support 64bit rates for getsockopt(SO_MAX_PACING_RATE)

For legacy applications using 32bit variable, SO_MAX_PACING_RATE
has to cap the returned value to 0xFFFFFFFF, meaning that
rates above 34.35 Gbit are capped.

This patch allows applications to read socket pacing rate
at full resolution, if they provide a 64bit variable to store it,
and the kernel is 64bit.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: support 64bit values for setsockopt(SO_MAX_PACING_RATE)

64bit kernels now support 64bit pacing rates.

This commit changes setsockopt() to accept 64bit
values provided by applications.

Old applications providing 32bit value are still supported,
but limited to the old 34Gbit limitation.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc-testing: Allow test cases to be skipped

By adding a check for an optional key/value pair to the test case
data, individual test cases may be skipped to prevent tdc from
aborting a test run due to setup or teardown failure.

If a test case is skipped, it will still appear in the results
output to allow for a consistent number of executed tests in each
run. However, the test will be marked as skipped.

This support for skipping extends to any plugins that may generate
additional results for each executed test.

Signed-off-by: Lucas Bates <lucasb@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'mlxsw-rehash-split'

Ido Schimmel says:

====================
mlxsw: spectrum_acl: Split rehash work into chunks

Jiri says:

When rehash happens on a vregion with many rules and they are being
migrated, it might take significant time to finish the job. During that
time vregion->lock is taken which prevents rules from being
added/deleted from the vregion.

Aim of this patchset is to allow to interrupt migration of rules during
rehash, reschedule and give chance for rules to be added/deleted. Then
continue migration in another execution of scheduled work.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Make mlxsw_sp_acl_tcam_vregion_rehash() return void

The return value is ignored anyway, so just return void.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Remember where to continue rehash migration

Store pointer to vchunk where the migration was interrupted, as well as
ventry pointer to start from and to stop at (during rollback). This
saved pointers need to be forgotten in case of ventries list or vchunk
list changes, which is done by couple of "changed" helpers.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Allow to interrupt/continue rehash work

Currently, migration of vregions with many entries may take long time
during which insertions and removals of the rules are blocked
due to wait to acquire vregion->lock.

To overcome this, allow to interrupt and continue rehash work according
to the set credits - number of rules to migrate.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Do rollback as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all()

In order to simplify the code and to prepare it for
interrupted/continued migration process, do the rollback in case of
migration error as another call to mlxsw_sp_acl_tcam_vchunk_migrate_all().
It can be understood as "migrate all back".

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Put vchunk migrate start/end code into separate functions

In preparations of interrupt/continue of rehash work, put the code that
is done at the beginning/end of vchunk migrate function into separate
functions.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Put this_is_rollback to rehash context struct

Put the this_is_rollback flag into rehash context struct in preparations
for interrupt/continue of rehash work.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Rename variables in mlxsw_sp_acl_tcam_ventry_migrate()

Remove some of variables in function mlxsw_sp_acl_tcam_ventry_migrate()
so the names are aligned with the rest of the code.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: assign vchunk->chunk by the newly created chunk

Make the vchunk->chunk contain pointer of a new chunk we migrate to.
In case of a rollback, it contains the original chunk.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: assign vregion->region by the newly created region

Make the vregion->region contain pointer of a new region we migrate to.
In case of a rollback, it contains the original region.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Push code start/end from mlxsw_sp_acl_tcam_vregion_migrate()

Push code from the beginning and end of function
mlxsw_sp_acl_tcam_vregion_migrate() into rehash_start()/end() functions.
Then all the things needed to be done before and after the actual
migration process will be grouped together.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Push rehash start/end code into separate functions

In preparations for interrupt/continue of rehash work, put the code at
the beginning/end of the rehash function into separate functions.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Introduce new rehash context struct and save hint_priv there

Prepare for continued migration. Introduce a new structure to track
rehash context and save hint_priv into it.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Don't migrate already migrated entry

Check if the entry is already in a chunk where we want it to be. In that
case, skip migration. This is preparation for "per parts" migration
where this situation may occur.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_acl: Push rehash dw struct into rehash sub-struct

More rehash related fields are going to come. Push "dw" into sub-struct
that will accommodate the others as well.

Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev: Remove unused transaction item queue

There are no more in tree users of the
switchdev_trans_item_{dequeue,enqueue} or switchdev_trans_item structure
in the kernel since commit 00fc0c51e35b ("rocker: Change world_ops API
and implementation to be switchdev independant").

Remove this unused code and update the documentation accordingly since.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'doc-net-ieee802154-move-from-plain-text-to-rst'

Stefan Schmidt says:

====================
doc: net: ieee802154: move from plain text to rst

The ieee802154 subsystem doc was still in plain text. With the networking book
taking shape I thought it was time to do the first step and move it over to rst.
This really is only the minimal conversion. I need to take some time to update
and extend the docs.

The patches are based on net-next, but they only touch the networking book so I
would not expect and trouble. From what I have seen they would go through
Jonathan's tree after being acked by Dave? If you want this patches against a
different tree let me know.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

doc: net: ieee802154: remove old plain text docs after switching to rst

The plain text docs are converted to rst now, which allows us to remove
the old text file from the tree.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

doc: net: ieee802154: introduce IEEE 802.15.4 subsystem doc in rst style

Moving the ieee802154 docs from a plain text file into the new rst
style. This commit only does the minimal needed change to bring the
documentation over. Follow up patches will improve and extend on this.

Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

devlink: fix kdoc

devlink suffers from a few kdoc warnings:

net/core/devlink.c:5292: warning: Function parameter or member 'dev' not described in 'devlink_register'
net/core/devlink.c:5351: warning: Function parameter or member 'port_index' not described in 'devlink_port_register'
net/core/devlink.c:5753: warning: Function parameter or member 'parent_resource_id' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Function parameter or member 'size_params' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'top_hierarchy' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'reload_required' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'parent_reosurce_id' description in 'devlink_resource_register'
net/core/devlink.c:6451: warning: Function parameter or member 'region' not described in 'devlink_region_snapshot_create'
net/core/devlink.c:6451: warning: Excess function parameter 'devlink_region' description in 'devlink_region_snapshot_create'

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-aquantia-minor-bug-fixes-after-static-analysis'

Igor Russkikh says:

====================
net: aquantia: minor bug fixes after static analysis

This patchset fixes minor errors and warnings found by smatch and kasan.

Extra patch is to replace AQ_HW_WAIT_FOR with readx_poll_timeout
to improve readability.

V2:
use readx_poll
resubmitted to net-next since the changeset became quite big.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: use better wrappers for state registers

Replace some direct registers reads with better
online functions.

Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: replace AQ_HW_WAIT_FOR with readx_poll_timeout_atomic

David noticed the original define was hiding 'err' variable
reference. Thats confusing and counterintuitive.

Andrew noted the whole macro could be replaced with standard readx_poll
kernel macro. This makes code more readable.

Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: fixed instack structure overflow

This is a real stack undercorruption found by kasan build.

The issue did no harm normally because it only overflowed
2 bytes after `bitary` array which on most architectures
were mapped into `err` local.

Fixes: bab6de8fd180 ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: fixed buffer overflow

The overflow is detected by smatch:

drivers/net/ethernet/aquantia/atlantic/aq_pci_func.c: 175
  aq_pci_func_free_irqs() error: buffer overflow 'self->aq_vec' 8 <= 31

In reality msix_entry_mask always restricts number of iterations.
Adding extra condition to make logic clear and smatch happy.

Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: added newline at end of file

drivers/net/ethernet/aquantia/atlantic/aq_nic.c: 991:1:
  warning: no newline at end of file

Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: aquantia: fixed memcpy size

Not careful array dereference caused analysis tools
to think there could be memory overflow.

There was actually no corruption because the array is
two dimensional.

drivers/net/ethernet/aquantia/atlantic/aq_ethtool.c: 140
  aq_ethtool_get_strings() error:
    memcpy() '*aq_ethtool_stat_names' too small (32 vs 704)

Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'nfp-control-processor-DMA-support-and-RJ45'

Jakub Kicinski says:

====================
nfp: control processor DMA support and RJ45

This series starts with adding support for reporting twisted pair
media type in ethtool.

Remaining patches add support for using DMA with the control/service
processor.  Currently we always copy the command data into card's
memory.  DMA support allows us to have the NSP read the data from
host memory by itself.  Unfortunately, the FW loading and flashing
cannot directly map the buffers for DMA because (a) the firmware
ABI returns const buffers, and (b) the buffers may be vmalloc()ed
in many mysterious/unmappable way.  So just bite the bullet -
allocate new host buffer for the command and copy.

As Dirk explains, the NSP now supports updating all FWs at once
which means the max flashing time grew significantly.  He bumps
the max wait to avoid timeouts.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: nsp: set higher timeout for flash bundle

The management firmware now supports being passed a bundle with
multiple components to be stored in flash at once. This makes it
easier to update all components to a known state with a single
user command, however, this also has the potential to increase
the time required to perform the update significantly.

The management firmware only updates the components out of a bundle
which are outdated, however, we need to make sure we can handle
the absolute worst case where a CPLD update can take a long time
to perform.

We set a very conservative total timeout of 900s which already
adds a contingency.

Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: nsp: allow the use of DMA buffer

Newer versions of NSP can access host memory.  Simplest access
type requires all data to be in one contiguous area.  Since we
don't have the guarantee on where callers of the NSP ABI will
allocate their buffers we allocate a bounce buffer and copy
the data in and out.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: nsp: move default buffer handling into its own function

DMA version of NSP communication is coming, move the code which
copies data into the NFP buffer into a separate function.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: nsp: use fractional size of the buffer

NSP expresses the buffer size in MB and 4 kB blocks.  For small
buffers the kB part may make a difference, so count it in.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nfp: report RJ45 connector in ethtool

Add support for reporting twisted pair port type.

Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: marvell: neta: disable comphy when setting mode

The comphy driver for Armada 3700 by Miquèl Raynal (which is currently
in linux-next) does not actually set comphy mode when phy_set_mode_ext
is called. The mode is set at next call of phy_power_on.

Update the driver to semantics similar to mvpp2: helper
mvneta_comphy_init sets comphy mode and powers it on.
When mode is to be changed in mvneta_mac_config, first power the comphy
off, then call mvneta_comphy_init (which sets the mode to new one).

Only do this when new mode is different from old mode.

This should also work for Armada 38x, since in that comphy driver
methods power_on and power_off are unimplemented.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'enetc-Add-mdio-support-and-device-tree-nodes'

Claudiu Manoil says:

====================
enetc: Add mdio support and device tree nodes

This is the missing part to enable PCI probing of the ENETC ethernet
ports on the LS1028A SoC and external traffic on the LS1028A RDB board.
It's one of the first items on the TODO list for the recently merged
ENETC ethernet driver.

v3: Add DT bindings doc for ENETC connections
v4: none
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: freescale: enetc: Add connection bindings for ENETC ethernet nodes

Define connection bindings (external PHY connections and internal links)
for the ENETC on-chip ethernet controllers.

Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

enetc: Add ENETC PF level external MDIO support

Each ENETC PF has its own MDIO interface, the corresponding
MDIO registers are mapped in the ENETC's Port register block.
The current patch adds a driver for these PF level MDIO buses,
so that each PF can manage directly its own external link.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

arm64: dts: fsl: ls1028a-rdb: Add ENETC external eth ports for the LS1028A RDB board

The LS1028A RDB board features an Atheros PHY connected over
SGMII to the ENETC PF0 (or Port0).  ENETC Port1 (PF1) has no
external connection on this board, so it can be disabled for now.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

arm64: dts: fsl: ls1028a: Add PCI IERC node and ENETC endpoints

The LS1028A SoC features a PCI Integrated Endpoint Root Complex
(IERC) defining several integrated PCI devices, including the ENETC
ethernet controller integrated endpoints (IEPs). The IERC implements
ECAM (Enhanced Configuration Access Mechanism) to provide access
to the PCIe config space of the IEPs. This means the the IEPs
(including ENETC) do not support the standard PCIe BARs, instead
the Enhanced Allocation (EA) capability structures in the ECAM space
are used to fix the base addresses in the system, and the PCI
subsystem uses these structures for device enumeration and discovery.
The "ranges" entries contain basic information from these EA capabily
structures required by the kernel for device enumeration.

The current patch also enables the first 2 ENETC PFs (Physiscal
Functions) and the associated VFs (Virtual Functions), 2 VFs for
each PF.  Each of these ENETC PFs has an external ethernet port
on the LS1028A SoC.

Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

selftests: rtnetlink: use internal netns switch for ip commands

'ip' can switch network namespaces internally and then run a given
command relative to that namespace without the need to fork and exec
another ip instance. Update all references of the form:
    ip netns exec "$testns" ip ...
to
    ip -netns "$testns" ...

Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 's390-qeth-next'

Julian Wiedmann says:

====================
s390/qeth: updates 2019-02-28

please apply one more qeth patch series for net-next. This eliminates
some of the quirks in our reset code, and slims down the internal
state machine.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: drop redundant state checking

Now that qeth always uses dev_close() to shutdown the interface, we can
trust the locking and remove some custom state checks.
qeth_l?_stop_card() is no longer called for a card in UP state, so remove
the checks there too. This basically makes the UP state obsolete, so rip
out the whole thing (except for the sysfs-visible string).

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: don't special-case HW trap during suspend

It makes no difference whether we
1. manually disarm the HW trap and call the offline code with
   recovery_mode == 1, or
2. call the offline code with recovery_mode == 0, and let it disarm the
   HW trap for us.

So consolidate the two code paths in the suspend callback.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: remove driver-wide workqueue

The qeth-wide workqueue is now only used by a single caller to schedule
close_dev work. Just put it on a system queue instead.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: don't defer close_dev work during recovery

The recovery code already runs in a kthread, we don't have to defer the
offlining further.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: remove a redundant check for card->dev

smatch complains that __qeth_l3_set_offline() first accesses card->dev,
and then later checks whether the pointer is valid.
Since commit d3d1b205e89f ("s390/qeth: allocate netdevice early"), the
pointer is _always_ valid - that patch merely missed to remove this one
check.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: call dev_close() during recovery

When resetting an interface ("recovery"), qeth currently attempts to
elide the call to dev_close(). We initially only call .ndo_close to
quiesce the data path, and then offline & online the ccwgroup device.
If the reset succeeded, a call to .ndo_open then resumes the data path
along with some internal setup (dev_addr validation, RX modeset) that
dev_open() would have usually triggered.
dev_close() only gets called (via the close_dev worker) if the reset
action fails.

It's unclear whether this was initially done due to locking concerns, or
rather to execute the reset transparently. Either way, temporarily
closing the interface without dev_close() is fragile, and means we're
susceptible to various races and unexpected behaviour. For instance:

- Bypassing dev_deactivate_many() means that the qdiscs are not set to
__QDISC_STATE_DEACTIVATED. Consequently any intermittent TX completion
can wake up the txq, resulting in calls to .ndo_start_xmit while the
data path is down. We have custom state checking to detect this case
and drop such packets.

- Because the IFF_UP flag doesn't reflect the interface's actual state
during a reset, we have custom state checking in .ndo_open and
.ndo_close to guard against invalid calls.

- Considering that the reset might take a considerable amount of time
(in particular if an IO fails and we end up waiting for its timeout), we
_do_ want NETDEV_GOING_DOWN and NETDEV_DOWN events so that components
like bonding, team, bridge, macvlan, vlan, ... can take appropriate
action.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: unconditionally clear MAC_REGISTERED flag

In its attempt to run only the minimal amount of tear down steps,
qeth_l2_stop_card() fails to reset the "is dev_addr registered?" flag
in some rare scenarios. But a future change to the tear down sequence
would cause us to _always_ hit this issue, so patch it up before that
code lands.

Fix it by unconditionally clearing the flag bit. This also allows us to
remove the additional cleanup step in qeth_dev_layer2_store().

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: enable/disable the HW trap a little earlier

When setting a L2 qeth device online, enable the HW trap as soon as the
control plane is available. This allows us to catch any error that
occurs during the very first commands.

In the same spirit, the offline code should disable the HW trap as the
very first step of its processing.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

s390/qeth: remove RECOVER state

The offline code uses a specific RECOVER state to indicate that the
interface should be brought up when a qeth device is set online again.

Rather than having a specific card-state for this, just put it in an
internal flag bit and set the state to DOWN. When working with the
card's state transitions, this reduces the complexity quite a bit.

Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net/smc: allow pnetid-less configuration

Without hardware pnetid support there must currently be a pnet
table configured to determine the IB device port to be used for SMC
RDMA traffic. This patch enables a setup without pnet table, if
the used handshake interface belongs already to a RoCE port.

Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: pie: avoid slow division in drop probability decay

As per RFC 8033, it is sufficient for the drop probability
decay factor to have a value of (1 - 1/64) instead of 98%.
This avoids the need to do slow division.

Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4vf: Enter debugging mode if FW is inaccessible

If we are not able to reach firmware, enter debugging mode that will
help us to get adapter logs.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4: Enable outer UDP checksum offload for T6

T6 adapters support outer UDP checksum offload for
encapsulated packets, hence enabling netdev feature flag
NETIF_F_GSO_UDP_TUNNEL_CSUM.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cxgb4/cxgb4vf: Fix up netdev->hw_features

GRO is done by cxgb4/cxgb4vf. Hence set NETIF_F_GRO flag for
both cxgb4/cxgb4vf.
Cleaned up VLAN netdev features in cxgb4vf. Also fixed
NETIF_F_HIGHDMA being set unconditionally for vlan netdev
features.

Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: act_csum: Fix csum calc for tagged packets

The csum calculation is different for IPv4/6. For VLAN packets,
tc_skb_protocol returns the VLAN protocol rather than the packet's one
(e.g. IPv4/6), so csum is not calculated. Furthermore, VLAN may not be
stripped so csum is not calculated in this case too. Calculate the
csum for those cases.

Fixes: d8b9605d2697 ("net: sched: fix skb->protocol use in case of accelerated vlan path")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: hns: use struct_size() in devm_kzalloc()

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = devm_kzalloc(dev, sizeof(struct foo) + sizeof(struct boo) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = devm_kzalloc(dev, struct_size(instance, entry, count), GFP_KERNEL);

This code was detected with the help of Coccinelle.

Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-phy-marvell10g-Clean-get_features-by-using-C45-helpers'

Maxime Chevallier says:

====================
net: phy: marvell10g: Clean .get_features by using C45 helpers

Recent work on C45 helpers by Heiner made the
genphy_c45_pma_read_abilities function generic enough to use as a
default .get_featutes implementation.

This series removes the remaining redundant code in
mv3310_get_features(), and makes the 2110 PHY use
genphy_c45_pma_read_abilities() directly, since it doesn't have the
issue with the wrong abilities being reported.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: marvell10g: Use the generic C45 helper to read the 2110 features

Contrary to the 3310, the 2110 PHY correctly reports it's 2.5G/5G
abilities. We can therefore use the genphy_c45_pma_read_abilities helper
to build the list of features.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: phy: marvell10g: Let genphy_c45_pma_read_abilities set Aneg bit

The genphy_c45_pma_read_abilities helper now sets the Autoneg ability
in phydev->supported according to what the AN MMD reports.

We therefore don't need to manually do that in mv3310_get_features().

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: act_tunnel_key: fix metadata handling

Tunnel key action params->tcft_enc_metadata is only set when action is
TCA_TUNNEL_KEY_ACT_SET. However, metadata pointer is incorrectly
dereferenced during tunnel key init and release without verifying that
action is if correct type, which causes NULL pointer dereference. Metadata
tunnel dst_cache is also leaked on action overwrite.

Fix metadata handling:
- Verify that metadata pointer is not NULL before dereferencing it in
  tunnel_key_init error handling code.
- Move dst_cache destroy code into tunnel_key_release_params() function
  that is called in both action overwrite and release cases (fixes resource
  leak) and verifies that actions has correct type before dereferencing
  metadata pointer (fixes NULL pointer dereference).

Oops with KASAN enabled during tdc tests execution:

[  261.080482] ==================================================================
[  261.088049] BUG: KASAN: null-ptr-deref in dst_cache_destroy+0x21/0xa0
[  261.094613] Read of size 8 at addr 00000000000000b0 by task tc/2976
[  261.102524] CPU: 14 PID: 2976 Comm: tc Not tainted 5.0.0-rc7+ #157
[  261.108844] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[  261.116726] Call Trace:
[  261.119234]  dump_stack+0x9a/0xeb
[  261.122625]  ? dst_cache_destroy+0x21/0xa0
[  261.126818]  ? dst_cache_destroy+0x21/0xa0
[  261.131004]  kasan_report+0x176/0x192
[  261.134752]  ? idr_get_next+0xd0/0x120
[  261.138578]  ? dst_cache_destroy+0x21/0xa0
[  261.142768]  dst_cache_destroy+0x21/0xa0
[  261.146799]  tunnel_key_release+0x3a/0x50 [act_tunnel_key]
[  261.152392]  tcf_action_cleanup+0x2c/0xc0
[  261.156490]  tcf_generic_walker+0x4c2/0x5c0
[  261.160794]  ? tcf_action_dump_1+0x390/0x390
[  261.165163]  ? tunnel_key_walker+0x5/0x1a0 [act_tunnel_key]
[  261.170865]  ? tunnel_key_walker+0xe9/0x1a0 [act_tunnel_key]
[  261.176641]  tca_action_gd+0x600/0xa40
[  261.180482]  ? tca_get_fill.constprop.17+0x200/0x200
[  261.185548]  ? __lock_acquire+0x588/0x1d20
[  261.189741]  ? __lock_acquire+0x588/0x1d20
[  261.193922]  ? mark_held_locks+0x90/0x90
[  261.197944]  ? mark_held_locks+0x90/0x90
[  261.202018]  ? __nla_parse+0xfe/0x190
[  261.205774]  tc_ctl_action+0x218/0x230
[  261.209614]  ? tcf_action_add+0x230/0x230
[  261.213726]  rtnetlink_rcv_msg+0x3a5/0x600
[  261.217910]  ? lock_downgrade+0x2d0/0x2d0
[  261.222006]  ? validate_linkmsg+0x400/0x400
[  261.226278]  ? find_held_lock+0x6d/0xd0
[  261.230200]  ? match_held_lock+0x1b/0x210
[  261.234296]  ? validate_linkmsg+0x400/0x400
[  261.238567]  netlink_rcv_skb+0xc7/0x1f0
[  261.242489]  ? netlink_ack+0x470/0x470
[  261.246319]  ? netlink_deliver_tap+0x1f3/0x5a0
[  261.250874]  netlink_unicast+0x2ae/0x350
[  261.254884]  ? netlink_attachskb+0x340/0x340
[  261.261647]  ? _copy_from_iter_full+0xdd/0x380
[  261.268576]  ? __virt_addr_valid+0xb6/0xf0
[  261.275227]  ? __check_object_size+0x159/0x240
[  261.282184]  netlink_sendmsg+0x4d3/0x630
[  261.288572]  ? netlink_unicast+0x350/0x350
[  261.295132]  ? netlink_unicast+0x350/0x350
[  261.301608]  sock_sendmsg+0x6d/0x80
[  261.307467]  ___sys_sendmsg+0x48e/0x540
[  261.313633]  ? copy_msghdr_from_user+0x210/0x210
[  261.320545]  ? save_stack+0x89/0xb0
[  261.326289]  ? __lock_acquire+0x588/0x1d20
[  261.332605]  ? entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  261.340063]  ? mark_held_locks+0x90/0x90
[  261.346162]  ? do_filp_open+0x138/0x1d0
[  261.352108]  ? may_open_dev+0x50/0x50
[  261.357897]  ? match_held_lock+0x1b/0x210
[  261.364016]  ? __fget_light+0xa6/0xe0
[  261.369840]  ? __sys_sendmsg+0xd2/0x150
[  261.375814]  __sys_sendmsg+0xd2/0x150
[  261.381610]  ? __ia32_sys_shutdown+0x30/0x30
[  261.388026]  ? lock_downgrade+0x2d0/0x2d0
[  261.394182]  ? mark_held_locks+0x1c/0x90
[  261.400230]  ? do_syscall_64+0x1e/0x280
[  261.406172]  do_syscall_64+0x78/0x280
[  261.411932]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  261.419103] RIP: 0033:0x7f28e91a8b87
[  261.424791] Code: 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 80 00 00 00 00 8b 05 6a 2b 2c 00 48 63 d2 48 63 ff 85 c0 75 18 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 59 f3 c3 0f 1f 80 00 00 00 00 53 48 89 f3 48
[  261.448226] RSP: 002b:00007ffdc5c4e2d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  261.458183] RAX: ffffffffffffffda RBX: 000000005c73c202 RCX: 00007f28e91a8b87
[  261.467728] RDX: 0000000000000000 RSI: 00007ffdc5c4e340 RDI: 0000000000000003
[  261.477342] RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000000c
[  261.486970] R10: 000000000000000c R11: 0000000000000246 R12: 0000000000000001
[  261.496599] R13: 000000000067b4e0 R14: 00007ffdc5c5248c R15: 00007ffdc5c52480
[  261.506281] ==================================================================
[  261.516076] Disabling lock debugging due to kernel taint
[  261.523979] BUG: unable to handle kernel NULL pointer dereference at 00000000000000b0
[  261.534413] #PF error: [normal kernel read fault]
[  261.541730] PGD 8000000317400067 P4D 8000000317400067 PUD 316878067 PMD 0
[  261.551294] Oops: 0000 [#1] SMP KASAN PTI
[  261.557985] CPU: 14 PID: 2976 Comm: tc Tainted: G    B             5.0.0-rc7+ #157
[  261.568306] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017
[  261.578874] RIP: 0010:dst_cache_destroy+0x21/0xa0
[  261.586413] Code: f4 ff ff ff eb f6 0f 1f 00 0f 1f 44 00 00 41 56 41 55 49 c7 c6 60 fe 35 af 41 54 55 49 89 fc 53 bd ff ff ff ff e8 ef 98 73 ff <49> 83 3c 24 00 75 35 eb 6c 4c 63 ed e8 de 98 73 ff 4a 8d 3c ed 40
[  261.611247] RSP: 0018:ffff888316447160 EFLAGS: 00010282
[  261.619564] RAX: 0000000000000000 RBX: ffff88835b3e2f00 RCX: ffffffffad1c5071
[  261.629862] RDX: 0000000000000003 RSI: dffffc0000000000 RDI: 0000000000000297
[  261.640149] RBP: 00000000ffffffff R08: fffffbfff5dd4e89 R09: fffffbfff5dd4e89
[  261.650467] R10: 0000000000000001 R11: fffffbfff5dd4e88 R12: 00000000000000b0
[  261.660785] R13: ffff8883267a10c0 R14: ffffffffaf35fe60 R15: 0000000000000001
[  261.671110] FS:  00007f28ea3e6400(0000) GS:ffff888364200000(0000) knlGS:0000000000000000
[  261.682447] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  261.691491] CR2: 00000000000000b0 CR3: 00000003178ae004 CR4: 00000000001606e0
[  261.701283] Call Trace:
[  261.706374]  tunnel_key_release+0x3a/0x50 [act_tunnel_key]
[  261.714522]  tcf_action_cleanup+0x2c/0xc0
[  261.721208]  tcf_generic_walker+0x4c2/0x5c0
[  261.728074]  ? tcf_action_dump_1+0x390/0x390
[  261.734996]  ? tunnel_key_walker+0x5/0x1a0 [act_tunnel_key]
[  261.743247]  ? tunnel_key_walker+0xe9/0x1a0 [act_tunnel_key]
[  261.751557]  tca_action_gd+0x600/0xa40
[  261.757991]  ? tca_get_fill.constprop.17+0x200/0x200
[  261.765644]  ? __lock_acquire+0x588/0x1d20
[  261.772461]  ? __lock_acquire+0x588/0x1d20
[  261.779266]  ? mark_held_locks+0x90/0x90
[  261.785880]  ? mark_held_locks+0x90/0x90
[  261.792470]  ? __nla_parse+0xfe/0x190
[  261.798738]  tc_ctl_action+0x218/0x230
[  261.805145]  ? tcf_action_add+0x230/0x230
[  261.811760]  rtnetlink_rcv_msg+0x3a5/0x600
[  261.818564]  ? lock_downgrade+0x2d0/0x2d0
[  261.825433]  ? validate_linkmsg+0x400/0x400
[  261.832256]  ? find_held_lock+0x6d/0xd0
[  261.838624]  ? match_held_lock+0x1b/0x210
[  261.845142]  ? validate_linkmsg+0x400/0x400
[  261.851729]  netlink_rcv_skb+0xc7/0x1f0
[  261.857976]  ? netlink_ack+0x470/0x470
[  261.864132]  ? netlink_deliver_tap+0x1f3/0x5a0
[  261.870969]  netlink_unicast+0x2ae/0x350
[  261.877294]  ? netlink_attachskb+0x340/0x340
[  261.883962]  ? _copy_from_iter_full+0xdd/0x380
[  261.890750]  ? __virt_addr_valid+0xb6/0xf0
[  261.897188]  ? __check_object_size+0x159/0x240
[  261.903928]  netlink_sendmsg+0x4d3/0x630
[  261.910112]  ? netlink_unicast+0x350/0x350
[  261.916410]  ? netlink_unicast+0x350/0x350
[  261.922656]  sock_sendmsg+0x6d/0x80
[  261.928257]  ___sys_sendmsg+0x48e/0x540
[  261.934183]  ? copy_msghdr_from_user+0x210/0x210
[  261.940865]  ? save_stack+0x89/0xb0
[  261.946355]  ? __lock_acquire+0x588/0x1d20
[  261.952358]  ? entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  261.959468]  ? mark_held_locks+0x90/0x90
[  261.965248]  ? do_filp_open+0x138/0x1d0
[  261.970910]  ? may_open_dev+0x50/0x50
[  261.976386]  ? match_held_lock+0x1b/0x210
[  261.982210]  ? __fget_light+0xa6/0xe0
[  261.987648]  ? __sys_sendmsg+0xd2/0x150
[  261.993263]  __sys_sendmsg+0xd2/0x150
[  261.998613]  ? __ia32_sys_shutdown+0x30/0x30
[  262.004555]  ? lock_downgrade+0x2d0/0x2d0
[  262.010236]  ? mark_held_locks+0x1c/0x90
[  262.015758]  ? do_syscall_64+0x1e/0x280
[  262.021234]  do_syscall_64+0x78/0x280
[  262.026500]  entry_SYSCALL_64_after_hwframe+0x49/0xbe
[  262.033207] RIP: 0033:0x7f28e91a8b87
[  262.038421] Code: 64 89 02 48 c7 c0 ff ff ff ff eb b9 0f 1f 80 00 00 00 00 8b 05 6a 2b 2c 00 48 63 d2 48 63 ff 85 c0 75 18 b8 2e 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 59 f3 c3 0f 1f 80 00 00 00 00 53 48 89 f3 48
[  262.060708] RSP: 002b:00007ffdc5c4e2d8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
[  262.070112] RAX: ffffffffffffffda RBX: 000000005c73c202 RCX: 00007f28e91a8b87
[  262.079087] RDX: 0000000000000000 RSI: 00007ffdc5c4e340 RDI: 0000000000000003
[  262.088122] RBP: 0000000000000000 R08: 0000000000000001 R09: 000000000000000c
[  262.097157] R10: 000000000000000c R11: 0000000000000246 R12: 0000000000000001
[  262.106207] R13: 000000000067b4e0 R14: 00007ffdc5c5248c R15: 00007ffdc5c52480
[  262.115271] Modules linked in: act_tunnel_key act_skbmod act_simple act_connmark nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 act_csum libcrc32c act_meta_skbtcindex act_meta_skbprio act_meta_mark act_ife ife act_police act_sample psample act_gact veth nfsv3 nfs_acl nfs lockd grace fscache bridge stp llc intel_rapl sb_edac mlx5_ib x86_pkg_temp_thermal sunrpc intel_powerclamp coretemp ib_uverbs kvm_intel ib_core kvm irqbypass mlx5_core crct10dif_pclmul crc32_pclmul crc32c_intel igb ghash_clmulni_intel intel_cstate mlxfw iTCO_wdt devlink intel_uncore iTCO_vendor_support ipmi_ssif ptp mei_me intel_rapl_perf ioatdma joydev pps_core ses mei i2c_i801 pcspkr enclosure lpc_ich dca wmi ipmi_si ipmi_devintf ipmi_msghandler acpi_pad acpi_power_meter pcc_cpufreq ast i2c_algo_bit drm_kms_helper ttm drm mpt3sas raid_class scsi_transport_sas
[  262.204393] CR2: 00000000000000b0
[  262.210390] ---[ end trace 2e41d786f2c7901a ]---
[  262.226790] RIP: 0010:dst_cache_destroy+0x21/0xa0
[  262.234083] Code: f4 ff ff ff eb f6 0f 1f 00 0f 1f 44 00 00 41 56 41 55 49 c7 c6 60 fe 35 af 41 54 55 49 89 fc 53 bd ff ff ff ff e8 ef 98 73 ff <49> 83 3c 24 00 75 35 eb 6c 4c 63 ed e8 de 98 73 ff 4a 8d 3c ed 40
[  262.258311] RSP: 0018:ffff888316447160 EFLAGS: 00010282
[  262.266304] RAX: 0000000000000000 RBX: ffff88835b3e2f00 RCX: ffffffffad1c5071
[  262.276251] RDX: 0000000000000003 RSI: dffffc0000000000 RDI: 0000000000000297
[  262.286208] RBP: 00000000ffffffff R08: fffffbfff5dd4e89 R09: fffffbfff5dd4e89
[  262.296183] R10: 0000000000000001 R11: fffffbfff5dd4e88 R12: 00000000000000b0
[  262.306157] R13: ffff8883267a10c0 R14: ffffffffaf35fe60 R15: 0000000000000001
[  262.316139] FS:  00007f28ea3e6400(0000) GS:ffff888364200000(0000) knlGS:0000000000000000
[  262.327146] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  262.335815] CR2: 00000000000000b0 CR3: 00000003178ae004 CR4: 00000000001606e0

Fixes: 41411e2fd6b8 ("net/sched: act_tunnel_key: Add dst_cache support")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers: net: phy: mdio-mux: Add support for Generic Mux controls

Add support for Generic Mux controls, when Mdio mux node is a consumer
of mux produced by some other device.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dt-bindings: net: Add bindings for mdio mux consumers

When we use the bindings defined in Documentation/devicetree/bindings/mux
to define mdio mux in producer and consumer terms, it results in two
devices. one is mux producer and other is mux consumer.

Add the bindings needed for Mdio mux consumer devices.

Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

route: Add multipath_hash in flowi_common to make user-define hash

Current fib_multipath_hash_policy can make hash based on the L3 or
L4. But it only work on the outer IP. So a specific tunnel always
has the same hash value. But a specific tunnel may contain so many
inner connections.

This patch provide a generic multipath_hash in floi_common. It can
make a user-define hash which can mix with L3 or L4 hash.

Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'net-Remove-switchdev_ops'

Florian Fainelli says:

====================
net: Remove switchdev_ops

This patch series completes the removal of the switchdev_ops by
converting switchdev_port_attr_set() to use either the blocking
(process) or non-blocking (atomic) notifier since we typically need to
deal with both depending on where in the bridge code we get called from.

This was tested with the forwarding selftests and DSA hardware.

Ido, hopefully this captures your comments done on v1, if not, can you
illustrate with some pseudo-code what you had in mind if that's okay?

Changes in v3:

- added Reviewed-by tags from Ido where relevant
- added missing notifier_to_errno() in net/bridge/br_switchdev.c when
  calling the atomic notifier for PRE_BRIDGE_FLAGS
- kept mlxsw_sp_switchdev_init() in mlxsw/

Changes in v2:

- do not check for SWITCHDEV_F_DEFER when calling the blocking notifier
  and instead directly call the atomic notifier from the single location
  where this is required
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

net: Remove switchdev_ops

Now that we have converted all possible callers to using a switchdev
notifier for attributes we do not have a need for implementing
switchdev_ops anymore, and this can be removed from all drivers the
net_device structure.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: switchdev: Replace port attr set SDO with a notification

Drop switchdev_ops.switchdev_port_attr_set. Drop the uses of this field
from all clients, which were migrated to use switchdev notification in
the previous patches.

Add a new function switchdev_port_attr_notify() that sends the switchdev
notifications SWITCHDEV_PORT_ATTR_SET and calls the blocking (process)
notifier chain.

We have one odd case within net/bridge/br_switchdev.c with the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier that
requires executing from atomic context, we deal with that one
specifically.

Drop __switchdev_port_attr_set() and update switchdev_port_attr_set()
likewise.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

staging: fsl-dpaa2: ethsw: Handle SWITCHDEV_PORT_ATTR_SET

Following patches will change the way we communicate setting a port's
attribute and use a blocking notifier to perform those tasks.

Prepare ethsw to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET and simply translate that into the existing
swdev_port_attr_set() call.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: mscc: ocelot: Handle SWITCHDEV_PORT_ATTR_SET

Following patches will change the way we communicate setting a port's
attribute and use notifiers to perform those tasks.

Ocelot does not currently have an atomic notifier registered for
switchdev events, so we need to register one in order to deal with
atomic context SWITCHDEV_PORT_ATTR_SET events.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum_switchdev: Handle SWITCHDEV_PORT_ATTR_SET

Following patches will change the way we communicate setting a port's
attribute and use a notifier to perform those tasks.

Prepare mlxsw to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET and utilize the switchdev_handle_port_attr_set()
to handle stacking of devices.

Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: dsa: Handle SWITCHDEV_PORT_ATTR_SET

Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.

Prepare DSA to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
dsa_slave_port_attr_set() can process.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rocker: Handle SWITCHDEV_PORT_ATTR_SET

Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.

Prepare rocker to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
rocker_port_attr_set() can process.

Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

switchdev: Add SWITCHDEV_PORT_ATTR_SET

In preparation for allowing switchdev enabled drivers to veto specific
attribute settings from within the context of the caller, introduce a
new switchdev notifier type for port attributes.

Suggested-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Revert "net: sched: fw: don't set arg->stop in fw_walk() when empty"

This reverts commit 31a998487641 ("net: sched: fw: don't set arg->stop in
fw_walk() when empty")

Cls API function tcf_proto_is_empty() was changed in commit
6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty")
to no longer depend on arg->stop to determine that classifier instance is
empty. Instead, it adds dedicated arg->nonempty field, which makes the fix
in fw classifier no longer necessary.

Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ethtool: Use explicit designated initializers for .cmd

Initialize the .cmd member by using a designated struct
initializer. This fixes warning of missing field initializers,
and makes code a little easier to read.

Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: pie: fix 64-bit division

Use div_u64() to resolve build failures on 32-bit platforms.

Fixes: 3f7ae5f3dc52 ("net: sched: pie: add more cases to auto-tune alpha and beta")
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Use RCU_POINTER_INITIALIZER() to init static variable

This pointer is RCU protected, so proper primitives should be used.

Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'tcp-cleanups'

Eric Dumazet says:

====================
tcp: cleanups for linux-5.1

This small patch series cleanups few things, and add a small
timewait optimization for hosts not using md5.
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: remove tcp_queue argument from tso_fragment()

tso_fragment() is only called for packets still in write queue.

Remove the tcp_queue parameter to make this more obvious,
even if the comment clearly states this.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: use tcp_md5_needed for timewait sockets

This might speedup tcp_twsk_destructor() a bit,
avoiding a cache line miss.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: convert tcp_md5_needed to static_branch API

We prefer static_branch_unlikely() over static_key_false() these days.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: get rid of __tcp_add_write_queue_tail()

This helper is only used from tcp_add_write_queue_tail(), and does
not make the code more readable.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tcp: get rid of tcp_check_send_head()

This helper is used only once, and its name is no longer relevant.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc-testing: gitignore, ignore local tdc config file

Comment in tdc_config.py recommends putting customizations in
tdc_config_local.py file that wasn't included in gitignore. Add the local
config file to gitignore.

Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: fix typo in walker_check_empty()

Function walker_check_empty() incorrectly verifies that tp pointer is not
NULL, instead of actual filter pointer. Fix conditional to check the right
pointer. Adjust filter pointer naming accordingly to other cls API
functions.

Fixes: 6676d5e416ee ("net: sched: set dedicated tcf_walker flag when tp is empty")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sched: pie: fix mistake in reference link

Fix the incorrect reference link to RFC 8033

Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mlxsw: spectrum: remove set but not used variable 'autoneg_status'

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/ethernet/mellanox/mlxsw/spectrum.c: In function 'mlxsw_sp_port_get_link_ksettings':
drivers/net/ethernet/mellanox/mlxsw/spectrum.c:3062:5: warning:
 variable 'autoneg_status' set but not used [-Wunused-but-set-variable]

It's not used since commit 475b33cb66c9 ("mlxsw: spectrum: Remove unsupported
eth_proto_lp_advertise field in PTYS")

Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'vxlan-create-and-changelink-extack-support'

Roopa Prabhu says:

====================
vxlan: create and changelink extack support

This series adds extack support to changelink paths.
In the process re-factors flag sets to a separate helper.
Also adds some changelink testcases to rtnetlink.sh

(This series was initially part of another series that
tried to support changelink for more attributes.
But after some feedback from sabrina, i have dropped the
'support changelink for more attributes' part because some
of them cannot be supported today or may require additional
use-case handling code. These can be done separately
as and when we see the need for it.)
====================

Signed-off-by: David S. Miller <davem@davemloft.net>

tools: selftests: rtnetlink: add testcases for vxlan flag sets

This patch extends rtnetlink.sh to cover some vxlan flag
netlink attribute sets.

Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>