Adam Ford [Thu, 26 Nov 2020 10:45:34 +0000 (04:45 -0600)]
arm64: dts: imx8mm-beacon-som: Configure RTC aliases
On the i.MX8MM Beacon SOM, there is an RTC chip which is fed power
from the baseboard during power off. The SNVS RTC integrated into
the SoC is not fed power. Depending on the order the modules are
loaded, this can be a problem if the external RTC isn't rtc0.
Make the alias for rtc0 point to the external RTC all the time and
rtc1 point to the SVNS in order to correctly hold date/time over
a power-cycle.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sat, 7 Nov 2020 11:58:08 +0000 (05:58 -0600)]
arm64: dts: imx8mn: Add node for SPDIF
The i.MX8M Nano can support SPDIF which is compatible to the
IP used on the i.MX35.
Add the node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sat, 7 Nov 2020 11:58:07 +0000 (05:58 -0600)]
arm64: dts: imx8mn: Add support for micfil
The i.MX8M Nano has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.
Add the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sat, 7 Nov 2020 11:58:06 +0000 (05:58 -0600)]
arm64: dts: imx8mn: Add SAI nodes
The i.MX8M Nano has several SAI nodes available to it.
Enable them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sat, 7 Nov 2020 11:58:05 +0000 (05:58 -0600)]
arm64: dts: imx8mn: Enable Asynchronous Sample Rate Converter
The driver exists for the Enhanced Asynchronous Sample Rate Converter
(EASRC) Controller, but there isn't a device tree entry for it.
On the vendor kernel, they put this on a spba-bus for SDMA support.
Add the node for the spba-bus with the easrc node inside.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vladimir Oltean [Thu, 19 Nov 2020 16:38:21 +0000 (18:38 +0200)]
arm64: dts: ls1028a: make the eMMC and SD card controllers use fixed indices
As the boot order in the kernel continues to change, sometimes it may
happen that the eSDHC controller mmc@2150000 (the one for eMMC) gets
probed before the one at mmc@2140000 (for external SD cards). The effect
is that the eMMC controller gets the /dev/mmcblk0 name, and the SD card
gets /dev/mmcblk1.
Since the introduction of this SoC, that has never happened in practice,
even though it was never guaranteed in theory. Setting
"root=/dev/mmcblk0p2" in /proc/cmdline has always caused the kernel to
use the second partition from the SD card as the rootfs.
The NXP development boards are typically shipped with either
- LSDK, which uses "root=UUID=", or
- OpenIL, which uses "root=/dev/mmcblkNp2"
So for OpenIL, let's preserve that old behavior by adding some aliases
which create naming consistency (for LSDK it doesn't matter):
- the SD card controller uses /dev/mmcblk0
- the eMMC controller uses /dev/mmcblk1
For the Kontron SL28 boards, Michael Walle says that they are shipped
with "root=UUID=" already, so the probing order doesn't matter, but it
is more natural to him for /dev/mmcblk0 to be the eMMC, so let's do it
the other way around there.
The aliases are parsed by mmc_alloc_host() in drivers/mmc/core/host.c.
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Yuantian Tang [Tue, 17 Nov 2020 03:43:04 +0000 (11:43 +0800)]
arm64: dts: freescale: update calibration table for TMU module
Update the calibration table to make the temperature more accurate.
Three platforms have been updated: ls1012a, ls1043a and ls1046a.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Sun, 15 Nov 2020 22:54:35 +0000 (23:54 +0100)]
arm64: dts: freescale: sl28: combine SPI MTD partitions
The upstream port, doesn't really follow the vendor partitioning. The
bootloader partition has one U-Boot FIT image containing all needed
bits and pieces. Even today the bootloader is already larger than the
current "bootloader" partition. Thus, fold all the partitions into one
and keep the environment one. The latter is still valid.
We keep the failsafe partitions because the first half of the SPI flash
is preinstalled by the vendor and immutable.
Fixes:
815364d0424e ("arm64: dts: freescale: add Kontron sl28 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Sun, 15 Nov 2020 22:53:14 +0000 (23:53 +0100)]
arm64: dts: ls1028a: add optee node
Add the optee node which can either be enabled by a specific board or by
the bootloader.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Sun, 8 Nov 2020 18:51:06 +0000 (19:51 +0100)]
arm64: dts: ls1028a: fix FlexSPI clock input
On the LS1028A the FlexSPI clock is connected to the first HWA output,
see Figure 7 "Clock subsystem block diagram".
Fixes:
c77fae5ba09a ("arm64: dts: ls1028a: Add FlexSPI support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Sun, 8 Nov 2020 18:51:05 +0000 (19:51 +0100)]
arm64: dts: ls1028a: fix ENETC PTP clock input
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes:
49401003e260 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nathan Chancellor [Sun, 8 Nov 2020 19:16:15 +0000 (12:16 -0700)]
arm64: dts: imx: Fix imx8mm-kontron-n801x-s.dtb target
While running 'make dtbs_install', the following error occurs:
make[3]: *** No rule to make target 'rootfs/freescale/imx8mm-kontron-n801x-s.dts', needed by '__dtbs_install'.
It should be .dtb, not .dts.
Fixes:
8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Joakim Zhang [Mon, 2 Nov 2020 02:25:27 +0000 (10:25 +0800)]
arm64: dts: imx8mn-evk: add IR support
Add IR support on i.MX8MN EVK board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Joakim Zhang [Mon, 2 Nov 2020 02:25:26 +0000 (10:25 +0800)]
arm64: dts: imx8mm-evk: add IR support
Add IR support on i.MX8MM EVK board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Joakim Zhang [Mon, 2 Nov 2020 02:25:25 +0000 (10:25 +0800)]
arm64: dts: imx8mq-evk: add linux,autosuspend-period property for IR
Add linux,autosuspend-period property for IR, details please refer to:
commit
ff1c9223b7b8 ("media: rc: gpio-ir-recv: add QoS support for cpuidle system")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Joakim Zhang [Mon, 2 Nov 2020 02:16:34 +0000 (10:16 +0800)]
arm64: dts: imx8mp-evk: add CAN support
Add CAN device node and pinctrl on i.MX8MP evk board.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shengjiu Wang [Mon, 2 Nov 2020 02:11:17 +0000 (10:11 +0800)]
arm64: dts: imx8mq-evk: Add spdif sound card support
There are two spdif IP on imx8mq, spdif1 is for normal
spdif device, spdif2 is for HDMI ARC interface.
Enable these spdif sound card in this patch.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Shengjiu Wang [Mon, 2 Nov 2020 02:11:16 +0000 (10:11 +0800)]
arm64: dts: imx8mq: Configure clock rate for audio plls
Configure clock rate for audio plls. audio pll1 is used
as parent clock for clocks that is multiple of 8kHz.
audio pll2 is used as parent clock for clocks that is
multiple of 11kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Xiaowei Bao [Mon, 2 Nov 2020 05:44:17 +0000 (13:44 +0800)]
arm64: dts: layerscape: Add PCIe EP node for ls1088a
Add PCIe EP node for ls1088a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:55 +0000 (13:35 +0200)]
arm64: dts: lx2160ardb: add nodes for the AQR107 PHYs
Annotate the EMDIO1 node and describe the 2 AQR107 PHYs found on the
LX2160ARDB board. Also, add the necessary phy-handles for DPMACs 3 and 4
to their associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:54 +0000 (13:35 +0200)]
arm64: dts: lx2160a: add PCS MDIO and PCS PHY nodes
Add PCS MDIO nodes for the internal MDIO buses on the LX2160A, along
with their internal PCS PHYs, which will be used when the DPMAC is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:53 +0000 (13:35 +0200)]
arm64: dts: ls208xa: add PCS MDIO and PCS PHY nodes
Add PCS MDIO nodes for the internal MDIO buses on the LS208x SoCs, along
with their internal PCS PHYs which will be used when the DPMAC object is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:52 +0000 (13:35 +0200)]
arm64: dts: ls2088ardb: add PHY nodes for the AQR405 PHYs
Annotate the EMDIO2 node and describe the other 4 10GBASER PHYs found on
the LS2088ARDB board. Also, add phy-handles for DPMACs 5-8 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:51 +0000 (13:35 +0200)]
arm64: dts: ls2088ardb: add PHY nodes for the CS4340 PHYs
Annotate the EMDIO1 node and describe the 4 10GBASER PHYs found on the
LS2088ARDB board. Also, add phy-handles for DPMACs 1-4 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:50 +0000 (13:35 +0200)]
arm64: dts: ls208xa: add the external MDIO nodes
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:49 +0000 (13:35 +0200)]
arm64: dts: ls1088ardb: add necessary DTS nodes for DPMAC2
Annotate the external MDIO2 node and describe the 10GBASER PHY found on
the LS1088ARDB board and add a phy-handle for DPMAC2 to link it.
Also, add the internal PCS MDIO node for the internal MDIO buses found
on the LS1088A SoC along with its internal PCS PHY and link the
corresponding DPMAC to the PCS through the pcs-handle.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:48 +0000 (13:35 +0200)]
arm64: dts: ls1088ardb: add QSGMII PHY nodes
Annotate the external MDIO1 node and describe the 8 QSGMII PHYs found on
the LS1088ARDB board and add phy-handles for DPMACs 3-10 to its
associated PHY. Also, add the internal PCS MDIO nodes for the internal
MDIO buses found on the LS1088A SoC along with their internal PCS PHY
and link the corresponding DPMAC to the PCS through the pcs-handle.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Ioana Ciornei [Fri, 30 Oct 2020 11:35:47 +0000 (13:35 +0200)]
arm64: dts: ls1088a: add external MDIO device nodes
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Meenakshi Aggarwal [Mon, 2 Nov 2020 05:59:41 +0000 (11:29 +0530)]
arm64: dts: lx2160a: add device tree for lx2162aqds board
Add device tree support for LX2162AQDS board.
LX2162A has same die as of LX2160A with different packaging.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Sat, 31 Oct 2020 12:31:14 +0000 (07:31 -0500)]
arm64: dts: imx8mm-beacon-som: Fix whitespace issue
The pinmux subnodes are indented too much. This patch does nothing
more than remove an extra tab. There are no functional changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Serge Semin [Tue, 20 Oct 2020 11:59:57 +0000 (14:59 +0300)]
arm64: dts: layerscape: Harmonize DWC USB3 DT nodes name
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Mon, 19 Oct 2020 16:50:37 +0000 (11:50 -0500)]
arm64: dts: imx8mm: Add node for SPDIF
The i.MX8M Mini can support SPDIF which is compatible to the
IP used on the i.MX35. Add the node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Mon, 19 Oct 2020 16:50:36 +0000 (11:50 -0500)]
arm64: dts: imx8mm: Add support for micfil
The i.MX8M Mini has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.
This patch adds the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 12 Oct 2020 12:44:02 +0000 (20:44 +0800)]
arm64: dts: imx8mp-evk: Correct WDOG_B pin configuration
Different revision of i.MX8MP EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MP boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 12 Oct 2020 12:44:01 +0000 (20:44 +0800)]
arm64: dts: imx8mn: Correct WDOG_B pin configuration
Different revision of i.MX8MN EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MN boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 12 Oct 2020 12:44:00 +0000 (20:44 +0800)]
arm64: dts: imx8mm: Correct WDOG_B pin configuration
Different revision of i.MX8MM EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MM boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 7 Oct 2020 14:24:08 +0000 (09:24 -0500)]
arm64: dts: imx8mm-beacon-som: Add QSPI NOR flash support
imx8mm-beacon-som has a Quad-SPI NOR flash connected to the FlexSPI bus.
This patch enables the FlexSPI bus and configures it to work with the
flash part.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adam Ford [Wed, 7 Oct 2020 14:04:57 +0000 (09:04 -0500)]
arm64: dts: imx8mm-beacon-som: Configure supplies on secondary cpus
Each cpu core should have a corresponding supply, but only cpu0 does.
This patch adds a supply for each of the secondary cpus.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Frieder Schrempf [Thu, 1 Oct 2020 15:13:37 +0000 (17:13 +0200)]
arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards
Kontron Electronics GmbH offers small and powerful SoMs based on the
i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.
The matching baseboards have the same form factor and similar interfaces
as the other boards from the Kontron "Board-Line" family, including
SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
RS485, CAN, LVDS or HDMI, RTC and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jacky Bai [Tue, 29 Sep 2020 09:15:23 +0000 (17:15 +0800)]
arm64: dts: freescale: Add pmu support on imx8mn
Add PMU node to enable pmu support on imx8mn.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Jacky Bai [Tue, 29 Sep 2020 09:15:22 +0000 (17:15 +0800)]
arm64: dts: freescale: Add pmu support on imx8mp
Add PMU node to enable pmu support on imx8mp.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Tue, 29 Sep 2020 08:40:15 +0000 (10:40 +0200)]
arm64: dts: imx8mp: adjust GIC CPU mask to match number of CPUs
i.MX 8M Plus has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Tue, 29 Sep 2020 08:40:14 +0000 (10:40 +0200)]
arm64: dts: imx8mn: adjust GIC CPU mask to match number of CPUs
i.MX 8M Nano has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Tue, 29 Sep 2020 08:40:13 +0000 (10:40 +0200)]
arm64: dts: imx8mm: adjust GIC CPU mask to match number of CPUs
i.MX 8M Mini has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Thu, 29 Oct 2020 16:21:33 +0000 (17:21 +0100)]
arm64: dts: freescale: align watchdog node name with dtschema
The dtschema expects watchdog device node name to be "watchdog":
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dt.yaml: wdog@2ad0000:
$nodename:0: 'wdog@2ad0000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Anson Huang [Mon, 28 Sep 2020 02:21:43 +0000 (10:21 +0800)]
arm64: dts: imx8mn-evk: Add cpu-supply to enable cpufreq
PMIC driver is ready on i.MX8MN EVK board, assign cpu-supply for
each A53 and restore the operating points table to enable cpufreq.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Thu, 1 Oct 2020 09:11:31 +0000 (11:11 +0200)]
arm64: dts: freescale: sl28: add CAN node
The module supports one CAN controller. Enable it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Michael Walle [Thu, 1 Oct 2020 09:11:30 +0000 (11:11 +0200)]
arm64: dts: ls1028a: add missing CAN nodes
The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.
The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Krzysztof Kozlowski [Sun, 20 Sep 2020 19:57:48 +0000 (21:57 +0200)]
arm64: dts: imx8mq-librem5: align GPIO hog names with dtschema
dtschema expects GPIO hogs to end with 'hog' suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Linus Torvalds [Sun, 25 Oct 2020 22:14:11 +0000 (15:14 -0700)]
Linux 5.10-rc1
Joe Perches [Thu, 22 Oct 2020 02:36:07 +0000 (19:36 -0700)]
treewide: Convert macro and uses of __section(foo) to __section("foo")
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/
75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rasmus Villemoes [Sat, 24 Oct 2020 01:04:26 +0000 (03:04 +0200)]
kernel/sys.c: fix prototype of prctl_get_tid_address()
tid_addr is not a "pointer to (pointer to int in userspace)"; it is in
fact a "pointer to (pointer to int in userspace) in userspace". So
sparse rightfully complains about passing a kernel pointer to
put_user().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Eric Biggers [Fri, 23 Oct 2020 23:27:16 +0000 (16:27 -0700)]
mm: remove kzfree() compatibility definition
Commit
453431a54934 ("mm, treewide: rename kzfree() to
kfree_sensitive()") renamed kzfree() to kfree_sensitive(),
but it left a compatibility definition of kzfree() to avoid
being too disruptive.
Since then a few more instances of kzfree() have slipped in.
Just get rid of them and remove the compatibility definition
once and for all.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joe Perches [Sat, 24 Oct 2020 23:59:04 +0000 (16:59 -0700)]
checkpatch: enable GIT_DIR environment use to set git repository location
If set, use the environment variable GIT_DIR to change the default .git
location of the kernel git tree.
If GIT_DIR is unset, keep using the current ".git" default.
Link: https://lkml.kernel.org/r/c5e23b45562373d632fccb8bc04e563abba4dd1d.camel@perches.com
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 25 Oct 2020 18:28:49 +0000 (11:28 -0700)]
Merge tag 'timers-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A time namespace fix and a matching selftest. The futex absolute
timeouts which are based on CLOCK_MONOTONIC require time namespace
corrected. This was missed in the original time namesapce support"
* tag 'timers-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
selftests/timens: Add a test for futex()
futex: Adjust absolute futex timeouts with per time namespace offset
Linus Torvalds [Sun, 25 Oct 2020 18:25:16 +0000 (11:25 -0700)]
Merge tag 'sched-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip
Pull scheduler fixes from Thomas Gleixner:
"Two scheduler fixes:
- A trivial build fix for sched_feat() to compile correctly with
CONFIG_JUMP_LABEL=n
- Replace a zero lenght array with a flexible array"
* tag 'sched-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/features: Fix !CONFIG_JUMP_LABEL case
sched: Replace zero-length array with flexible-array
Linus Torvalds [Sun, 25 Oct 2020 18:22:59 +0000 (11:22 -0700)]
Merge tag 'perf-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip
Pull perf fix from Thomas Gleixner:
"A single fix to compute the field offset of the SNOOPX bit in the data
source bitmask of perf events correctly"
* tag 'perf-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: correct SNOOPX field offset
Linus Torvalds [Sun, 25 Oct 2020 18:14:54 +0000 (11:14 -0700)]
Merge tag 'locking-urgent-2020-10-25' of git://git./linux/kernel/git/tip/tip
Pull locking fix from Thomas Gleixner:
"Just a trivial fix for kernel-doc warnings"
* tag 'locking-urgent-2020-10-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/seqlocks: Fix kernel-doc warnings
Linus Torvalds [Sun, 25 Oct 2020 18:12:31 +0000 (11:12 -0700)]
Merge tag 'ntb-5.10' of git://github.com/jonmason/ntb
Pull NTB fixes from Jon Mason.
* tag 'ntb-5.10' of git://github.com/jonmason/ntb:
NTB: Use struct_size() helper in devm_kzalloc()
ntb: intel: Fix memleak in intel_ntb_pci_probe
NTB: hw: amd: fix an issue about leak system resources
Linus Torvalds [Sun, 25 Oct 2020 18:10:23 +0000 (11:10 -0700)]
Merge branch 'i2c/for-5.10' of git://git./linux/kernel/git/wsa/linux
Pull i2c fix from Wolfram Sang:
"Regression fix for rc1 and stable kernels as well"
* 'i2c/for-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
Linus Torvalds [Sun, 25 Oct 2020 18:05:04 +0000 (11:05 -0700)]
Merge tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6
Pull more cifs updates from Steve French:
"Add support for stat of various special file types (WSL reparse points
for char, block, fifo)"
* tag '5.10-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6:
cifs: update internal module version number
smb3: add some missing definitions from MS-FSCC
smb3: remove two unused variables
smb3: add support for stat of WSL reparse points for special file types
Linus Torvalds [Sun, 25 Oct 2020 17:59:34 +0000 (10:59 -0700)]
Merge branch 'parisc-5.10-2' of git://git./linux/kernel/git/deller/parisc-linux
Pull more parisc updates from Helge Deller:
- During this merge window O_NONBLOCK was changed to become
000200000,
but we missed that the syscalls timerfd_create(), signalfd4(),
eventfd2(), pipe2(), inotify_init1() and userfaultfd() do a strict
bit-wise check of the flags parameter.
To provide backward compatibility with existing userspace we
introduce parisc specific wrappers for those syscalls which filter
out the old O_NONBLOCK value and replaces it with the new one.
- Prevent HIL bus driver to get stuck when keyboard or mouse isn't
attached
- Improve error return codes when setting rtc time
- Minor documentation fix in pata_ns87415.c
* 'parisc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
ata: pata_ns87415.c: Document support on parisc with superio chip
parisc: Add wrapper syscalls to fix O_NONBLOCK flag usage
hil/parisc: Disable HIL driver when it gets stuck
parisc: Improve error return codes when setting rtc time
Linus Torvalds [Sun, 25 Oct 2020 17:55:35 +0000 (10:55 -0700)]
Merge tag 'for-linus-5.10b-rc1c-tag' of git://git./linux/kernel/git/xen/tip
Pull more xen updates from Juergen Gross:
- a series for the Xen pv block drivers adding module parameters for
better control of resource usge
- a cleanup series for the Xen event driver
* tag 'for-linus-5.10b-rc1c-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
Documentation: add xen.fifo_events kernel parameter description
xen/events: unmask a fifo event channel only if it was masked
xen/events: only register debug interrupt for 2-level events
xen/events: make struct irq_info private to events_base.c
xen: remove no longer used functions
xen-blkfront: Apply changed parameter name to the document
xen-blkfront: add a parameter for disabling of persistent grants
xen-blkback: add a parameter for disabling of persistent grants
Linus Torvalds [Sun, 25 Oct 2020 17:45:26 +0000 (10:45 -0700)]
Merge tag 'safesetid-5.10' of git://github.com/micah-morton/linux
Pull SafeSetID updates from Micah Morton:
"The changes are mostly contained to within the SafeSetID LSM, with the
exception of a few 1-line changes to change some ns_capable() calls to
ns_capable_setid() -- causing a flag (CAP_OPT_INSETID) to be set that
is examined by SafeSetID code and nothing else in the kernel.
The changes to SafeSetID internally allow for setting up GID
transition security policies, as already existed for UIDs"
* tag 'safesetid-5.10' of git://github.com/micah-morton/linux:
LSM: SafeSetID: Fix warnings reported by test bot
LSM: SafeSetID: Add GID security policy handling
LSM: Signal to SafeSetID when setting group IDs
Linus Torvalds [Sun, 25 Oct 2020 17:40:08 +0000 (10:40 -0700)]
Merge tag '
20201024-v4-5.10' of git://git./linux/kernel/git/wtarreau/prandom
Pull random32 updates from Willy Tarreau:
"Make prandom_u32() less predictable.
This is the cleanup of the latest series of prandom_u32
experimentations consisting in using SipHash instead of Tausworthe to
produce the randoms used by the network stack.
The changes to the files were kept minimal, and the controversial
commit that used to take noise from the fast_pool (
f227e3ec3b5c) was
reverted. Instead, a dedicated "net_rand_noise" per_cpu variable is
fed from various sources of activities (networking, scheduling) to
perturb the SipHash state using fast, non-trivially predictable data,
instead of keeping it fully deterministic. The goal is essentially to
make any occasional memory leakage or brute-force attempt useless.
The resulting code was verified to be very slightly faster on x86_64
than what is was with the controversial commit above, though this
remains barely above measurement noise. It was also tested on i386 and
arm, and build- tested only on arm64"
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
* tag '
20201024-v4-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wtarreau/prandom:
random32: add a selftest for the prandom32 code
random32: add noise from network and scheduling activity
random32: make prandom_u32() output unpredictable
Hans de Goede [Wed, 14 Oct 2020 14:41:58 +0000 (16:41 +0200)]
i2c: core: Restore acpi_walk_dep_device_list() getting called after registering the ACPI i2c devs
Commit
21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler()
before i2c_acpi_register_devices()")'s intention was to only move the
acpi_install_address_space_handler() call to the point before where
the ACPI declared i2c-children of the adapter where instantiated by
i2c_acpi_register_devices().
But i2c_acpi_install_space_handler() had a call to
acpi_walk_dep_device_list() hidden (that is I missed it) at the end
of it, so as an unwanted side-effect now acpi_walk_dep_device_list()
was also being called before i2c_acpi_register_devices().
Move the acpi_walk_dep_device_list() call to the end of
i2c_acpi_register_devices(), so that it is once again called *after*
the i2c_client-s hanging of the adapter have been created.
This fixes the Microsoft Surface Go 2 hanging at boot.
Fixes:
21653a4181ff ("i2c: core: Call i2c_acpi_install_space_handler() before i2c_acpi_register_devices()")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209627
Reported-by: Rainer Finke <rainer@finke.cc>
Reported-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Suggested-by: Maximilian Luz <luzmaximilian@gmail.com>
Tested-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Linus Torvalds [Sat, 24 Oct 2020 19:46:42 +0000 (12:46 -0700)]
Merge tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph
- rdma error handling fixes (Chao Leng)
- fc error handling and reconnect fixes (James Smart)
- fix the qid displace when tracing ioctl command (Keith Busch)
- don't use BLK_MQ_REQ_NOWAIT for passthru (Chaitanya Kulkarni)
- fix MTDT for passthru (Logan Gunthorpe)
- blacklist Write Same on more devices (Kai-Heng Feng)
- fix an uninitialized work struct (zhenwei pi)"
- lightnvm out-of-bounds fix (Colin)
- SG allocation leak fix (Doug)
- rnbd fixes (Gioh, Guoqing, Jack)
- zone error translation fixes (Keith)
- kerneldoc markup fix (Mauro)
- zram lockdep fix (Peter)
- Kill unused io_context members (Yufen)
- NUMA memory allocation cleanup (Xianting)
- NBD config wakeup fix (Xiubo)
* tag 'block-5.10-2020-10-24' of git://git.kernel.dk/linux-block: (27 commits)
block: blk-mq: fix a kernel-doc markup
nvme-fc: shorten reconnect delay if possible for FC
nvme-fc: wait for queues to freeze before calling update_hr_hw_queues
nvme-fc: fix error loop in create_hw_io_queues
nvme-fc: fix io timeout to abort I/O
null_blk: use zone status for max active/open
nvmet: don't use BLK_MQ_REQ_NOWAIT for passthru
nvmet: cleanup nvmet_passthru_map_sg()
nvmet: limit passthru MTDS by BIO_MAX_PAGES
nvmet: fix uninitialized work for zero kato
nvme-pci: disable Write Zeroes on Sandisk Skyhawk
nvme: use queuedata for nvme_req_qid
nvme-rdma: fix crash due to incorrect cqe
nvme-rdma: fix crash when connect rejected
block: remove unused members for io_context
blk-mq: remove the calling of local_memory_node()
zram: Fix __zram_bvec_{read,write}() locking order
skd_main: remove unused including <linux/version.h>
sgl_alloc_order: fix memory leak
lightnvm: fix out-of-bounds write to array devices->info[]
...
Linus Torvalds [Sat, 24 Oct 2020 19:40:18 +0000 (12:40 -0700)]
Merge tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block
Pull io_uring fixes from Jens Axboe:
- fsize was missed in previous unification of work flags
- Few fixes cleaning up the flags unification creds cases (Pavel)
- Fix NUMA affinities for completely unplugged/replugged node for io-wq
- Two fallout fixes from the set_fs changes. One local to io_uring, one
for the splice entry point that io_uring uses.
- Linked timeout fixes (Pavel)
- Removal of ->flush() ->files work-around that we don't need anymore
with referenced files (Pavel)
- Various cleanups (Pavel)
* tag 'io_uring-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
splice: change exported internal do_splice() helper to take kernel offset
io_uring: make loop_rw_iter() use original user supplied pointers
io_uring: remove req cancel in ->flush()
io-wq: re-set NUMA node affinities if CPUs come online
io_uring: don't reuse linked_timeout
io_uring: unify fsize with def->work_flags
io_uring: fix racy REQ_F_LINK_TIMEOUT clearing
io_uring: do poll's hash_node init in common code
io_uring: inline io_poll_task_handler()
io_uring: remove extra ->file check in poll prep
io_uring: make cached_cq_overflow non atomic_t
io_uring: inline io_fail_links()
io_uring: kill ref get/drop in personality init
io_uring: flags-based creds init in queue
Linus Torvalds [Sat, 24 Oct 2020 19:36:24 +0000 (12:36 -0700)]
Merge tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block
Pull libata fixes from Jens Axboe:
"Two minor libata fixes:
- Fix a DMA boundary mask regression for sata_rcar (Geert)
- kerneldoc markup fix (Mauro)"
* tag 'libata-5.10-2020-10-24' of git://git.kernel.dk/linux-block:
ata: fix some kernel-doc markups
ata: sata_rcar: Fix DMA boundary mask
Linus Torvalds [Sat, 24 Oct 2020 19:26:05 +0000 (12:26 -0700)]
Merge branch 'work.misc' of git://git./linux/kernel/git/viro/vfs
Pull misc vfs updates from Al Viro:
"Assorted stuff all over the place (the largest group here is
Christoph's stat cleanups)"
* 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: remove KSTAT_QUERY_FLAGS
fs: remove vfs_stat_set_lookup_flags
fs: move vfs_fstatat out of line
fs: implement vfs_stat and vfs_lstat in terms of vfs_fstatat
fs: remove vfs_statx_fd
fs: omfs: use kmemdup() rather than kmalloc+memcpy
[PATCH] reduce boilerplate in fsid handling
fs: Remove duplicated flag O_NDELAY occurring twice in VALID_OPEN_FLAGS
selftests: mount: add nosymfollow tests
Add a "nosymfollow" mount option.
Linus Torvalds [Sat, 24 Oct 2020 19:17:05 +0000 (12:17 -0700)]
Merge tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping
Pull dma-mapping fixes from Christoph Hellwig:
- document the new dma_{alloc,free}_pages() API
- two fixups for the dma-mapping.h split
* tag 'dma-mapping-5.10-1' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: document dma_{alloc,free}_pages
dma-mapping: move more functions to dma-map-ops.h
ARM/sa1111: add a missing include of dma-map-ops.h
Linus Torvalds [Sat, 24 Oct 2020 19:09:22 +0000 (12:09 -0700)]
Merge tag 'for-linus' of git://git./virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"Two fixes for this merge window, and an unrelated bugfix for a host
hang"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: ioapic: break infinite recursion on lazy EOI
KVM: vmx: rename pi_init to avoid conflict with paride
KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build
Linus Torvalds [Sat, 24 Oct 2020 18:49:32 +0000 (11:49 -0700)]
Merge tag 'x86_seves_fixes_for_v5.10_rc1' of git://git./linux/kernel/git/tip/tip
Pull x86 SEV-ES fixes from Borislav Petkov:
"Three fixes to SEV-ES to correct setting up the new early pagetable on
5-level paging machines, to always map boot_params and the kernel
cmdline, and disable stack protector for ../compressed/head{32,64}.c.
(Arvind Sankar)"
* tag 'x86_seves_fixes_for_v5.10_rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot/64: Explicitly map boot_params and command line
x86/head/64: Disable stack protection for head$(BITS).o
x86/boot/64: Initialize 5-level paging variables earlier
Willy Tarreau [Sat, 24 Oct 2020 16:36:27 +0000 (18:36 +0200)]
random32: add a selftest for the prandom32 code
Given that this code is new, let's add a selftest for it as well.
It doesn't rely on fixed sets, instead it picks 1024 numbers and
verifies that they're not more correlated than desired.
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Willy Tarreau [Mon, 10 Aug 2020 08:27:42 +0000 (10:27 +0200)]
random32: add noise from network and scheduling activity
With the removal of the interrupt perturbations in previous random32
change (random32: make prandom_u32() output unpredictable), the PRNG
has become 100% deterministic again. While SipHash is expected to be
way more robust against brute force than the previous Tausworthe LFSR,
there's still the risk that whoever has even one temporary access to
the PRNG's internal state is able to predict all subsequent draws till
the next reseed (roughly every minute). This may happen through a side
channel attack or any data leak.
This patch restores the spirit of commit
f227e3ec3b5c ("random32: update
the net random state on interrupt and activity") in that it will perturb
the internal PRNG's statee using externally collected noise, except that
it will not pick that noise from the random pool's bits nor upon
interrupt, but will rather combine a few elements along the Tx path
that are collectively hard to predict, such as dev, skb and txq
pointers, packet length and jiffies values. These ones are combined
using a single round of SipHash into a single long variable that is
mixed with the net_rand_state upon each invocation.
The operation was inlined because it produces very small and efficient
code, typically 3 xor, 2 add and 2 rol. The performance was measured
to be the same (even very slightly better) than before the switch to
SipHash; on a 6-core 12-thread Core i7-8700k equipped with a 40G NIC
(i40e), the connection rate dropped from 556k/s to 555k/s while the
SYN cookie rate grew from 5.38 Mpps to 5.45 Mpps.
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
Cc: George Spelvin <lkml@sdf.org>
Cc: Amit Klein <aksecurity@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
George Spelvin [Sun, 9 Aug 2020 06:57:44 +0000 (06:57 +0000)]
random32: make prandom_u32() output unpredictable
Non-cryptographic PRNGs may have great statistical properties, but
are usually trivially predictable to someone who knows the algorithm,
given a small sample of their output. An LFSR like prandom_u32() is
particularly simple, even if the sample is widely scattered bits.
It turns out the network stack uses prandom_u32() for some things like
random port numbers which it would prefer are *not* trivially predictable.
Predictability led to a practical DNS spoofing attack. Oops.
This patch replaces the LFSR with a homebrew cryptographic PRNG based
on the SipHash round function, which is in turn seeded with 128 bits
of strong random key. (The authors of SipHash have *not* been consulted
about this abuse of their algorithm.) Speed is prioritized over security;
attacks are rare, while performance is always wanted.
Replacing all callers of prandom_u32() is the quick fix.
Whether to reinstate a weaker PRNG for uses which can tolerate it
is an open question.
Commit
f227e3ec3b5c ("random32: update the net random state on interrupt
and activity") was an earlier attempt at a solution. This patch replaces
it.
Reported-by: Amit Klein <aksecurity@gmail.com>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Eric Dumazet <edumazet@google.com>
Cc: "Jason A. Donenfeld" <Jason@zx2c4.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: tytso@mit.edu
Cc: Florian Westphal <fw@strlen.de>
Cc: Marc Plumb <lkml.mplumb@gmail.com>
Fixes:
f227e3ec3b5c ("random32: update the net random state on interrupt and activity")
Signed-off-by: George Spelvin <lkml@sdf.org>
Link: https://lore.kernel.org/netdev/20200808152628.GA27941@SDF.ORG/
[ willy: partial reversal of
f227e3ec3b5c; moved SIPROUND definitions
to prandom.h for later use; merged George's prandom_seed() proposal;
inlined siprand_u32(); replaced the net_rand_state[] array with 4
members to fix a build issue; cosmetic cleanups to make checkpatch
happy; fixed RANDOM32_SELFTEST build ]
Signed-off-by: Willy Tarreau <w@1wt.eu>
Linus Torvalds [Sat, 24 Oct 2020 18:09:13 +0000 (11:09 -0700)]
Merge tag 'powerpc-5.10-2' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- A fix for undetected data corruption on Power9 Nimbus <= DD2.1 in the
emulation of VSX loads. The affected CPUs were not widely available.
- Two fixes for machine check handling in guests under PowerVM.
- A fix for our recent changes to SMP setup, when
CONFIG_CPUMASK_OFFSTACK=y.
- Three fixes for races in the handling of some of our powernv sysfs
attributes.
- One change to remove TM from the set of Power10 CPU features.
- A couple of other minor fixes.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Ganesh Goudar, Jordan
Niethe, Mahesh Salgaonkar, Michael Neuling, Oliver O'Halloran, Qian Cai,
Srikar Dronamraju, Vasant Hegde.
* tag 'powerpc-5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/pseries: Avoid using addr_to_pfn in real mode
powerpc/uaccess: Don't use "m<>" constraint with GCC 4.9
powerpc/eeh: Fix eeh_dev_check_failure() for PE#0
powerpc/64s: Remove TM from Power10 features
selftests/powerpc: Make alignment handler test P9N DD2.1 vector CI load workaround
powerpc: Fix undetected data corruption with P9N DD2.1 VSX CI load emulation
powerpc/powernv/dump: Handle multiple writes to ack attribute
powerpc/powernv/dump: Fix race while processing OPAL dump
powerpc/smp: Use GFP_ATOMIC while allocating tmp mask
powerpc/smp: Remove unnecessary variable
powerpc/mce: Avoid nmi_enter/exit in real mode on pseries hash
powerpc/opal_elog: Handle multiple writes to ack attribute
Linus Torvalds [Sat, 24 Oct 2020 17:57:57 +0000 (10:57 -0700)]
Merge tag 'riscv-for-linus-5.10-mw1' of git://git./linux/kernel/git/riscv/linux
Pull more RISC-V updates from Palmer Dabbelt:
"Just a single patch set: the remainder of Christoph's work to remove
set_fs, including the RISC-V portion"
* tag 'riscv-for-linus-5.10-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove address space overrides using set_fs()
riscv: implement __get_kernel_nofault and __put_user_nofault
riscv: refactor __get_user and __put_user
riscv: use memcpy based uaccess for nommu again
asm-generic: make the set_fs implementation optional
asm-generic: add nommu implementations of __{get,put}_kernel_nofault
asm-generic: improve the nommu {get,put}_user handling
uaccess: provide a generic TASK_SIZE_MAX definition
Linus Torvalds [Sat, 24 Oct 2020 17:53:04 +0000 (10:53 -0700)]
Merge tag 'armsoc-defconfig' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC defconfig updates from Olof Johansson:
"We keep this in a separate branch to avoid cross-branch conflicts, but
most of the material here is fairly boring -- some new drivers turned
on for hardware since they were merged, and some refreshed files due
to time having moved a lot of entries around"
* tag 'armsoc-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (33 commits)
ARM: multi_v7_defconfig: add FMC2 EBI controller support
arm64: defconfig: enable Qualcomm ASoC modules
arm64: defconfig: qcom: enable GPU clock controller for SM8[12]50
arm64: defconfig: enable INTERCONNECT for Qualcomm chipsets
arm64: defconfig: enable the sl28cpld board management controller
arm64: defconfig: Enable the eLCDIF and Raydium RM67191 drivers
arm64: defconfig: Enable Qcom SNPS Femto PHY
ARM: configs: Update Realview defconfig
ARM: configs: Update Versatile defconfig
ARM: config: aspeed_g5: Enable IBM OP Panel driver
ARM: config: aspeed-g5: Enable I2C GPIO mux driver
ARM: config: aspeed: Fix selection of media drivers
arm64: defconfig: Enable Samsung S3FWRN5 NFC driver
ARM: omap2plus_defconfig: enable generic net options
ARM: omap2plus_defconfig: enable twl4030_madc as a loadable module
arm64: defconfig: Enable clock driver for ROHM BD718x7 PMIC
arm64: defconfig: Build ADMA and ACONNECT driver
arm64: defconfig: Build AHUB component drivers
arm64: defconfig: Enable Lontium LT9611 driver
arm64: defcondfig: Enable USB ACM and FTDI drivers
...
Linus Torvalds [Sat, 24 Oct 2020 17:44:18 +0000 (10:44 -0700)]
Merge tag 'armsoc-dt' of git://git./linux/kernel/git/soc/soc
Pull ARM Devicetree updates from Olof Johansson:
"As usual, most of the changes are to devicetrees.
Besides smaller fixes, some refactorings and cleanups, some of the new
platforms and chips (or significant features) supported are below:
Broadcom boards:
- Cisco Meraki MR32 (BCM53016-based)
- BCM2711 (RPi4) display pipeline support
Actions Semi boards:
- Caninos Loucos Labrador SBC (S500-based)
- RoseapplePi SBC (S500-based)
Allwinner SoCs/boards:
- A100 SoC with Perf1 board
- Mali, DMA, Cetrus and IR support for R40 SoC
Amlogic boards:
- Libretch S905x CC V2 board
- Hardkernel ODROID-N2+ board
Aspeed boards/platforms:
- Wistron Mowgli (AST2500-based, Power9 OpenPower server)
- Facebook Wedge400 (AST2500-based, ToR switch)
Hisilicon SoC:
- SD5203 SoC
Nvidia boards:
- Tegra234 VDK, for pre-silicon Orin SoC
NXP i.MX boards:
- Librem 5 phone
- i.MX8MM DDR4 EVK
- Variscite VAR-SOM-MX8MN SoM
- Symphony board
- Tolino Shine 2 HD
- TQMa6 SoM
- Y Soft IOTA Orion
Rockchip boards:
- NanoPi R2S board
- A95X-Z2 board
- more Rock-Pi4 variants
STM32 boards:
- Odyssey SOM board (STM32MP157CAC-based)
- DH DRC02 board
Toshiba SoCs/boards:
- Visconti SoC and TPMV7708 board"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (638 commits)
ARM: dts: nspire: Fix SP804 users
arm64: dts: lg: Fix SP804 users
arm64: dts: lg: Fix SP805 clocks
ARM: mstar: Fix up the fallout from moving the dts/dtsi files
ARM: mstar: Add mstar prefix to all of the dtsi/dts files
ARM: mstar: Add interrupt to pm_uart
ARM: mstar: Add interrupt controller to base dtsi
ARM: dts: meson8: remove two invalid interrupt lines from the GPU node
arm64: dts: ti: k3-j7200-common-proc-board: Add USB support
arm64: dts: ti: k3-j7200-common-proc-board: Configure the SERDES lane function
arm64: dts: ti: k3-j7200-main: Add USB controller
arm64: dts: ti: k3-j7200-main.dtsi: Add USB to SERDES lane MUX
arm64: dts: ti: k3-j7200-main: Add SERDES lane control mux
dt-bindings: ti-serdes-mux: Add defines for J7200 SoC
ARM: dts: hisilicon: add SD5203 dts
ARM: dts: hisilicon: fix the system controller compatible nodes
arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
arm64: dts: zynqmp: Remove undocumented u-boot properties
arm64: dts: zynqmp: Remove additional compatible string for i2c IPs
arm64: dts: zynqmp: Rename buses to be align with simple-bus yaml
...
Linus Torvalds [Sat, 24 Oct 2020 17:39:22 +0000 (10:39 -0700)]
Merge tag 'armsoc-drivers' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
Linus Torvalds [Sat, 24 Oct 2020 17:33:08 +0000 (10:33 -0700)]
Merge tag 'armsoc-soc' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Linus Torvalds [Sat, 24 Oct 2020 17:26:06 +0000 (10:26 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I had queued up a batch of fixes that got a bit close to the release
for sending in before the merge window opened, so I'm including them
in the merge window batch instead.
Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
through the releases"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
soc: actions: include header to fix missing prototype
arm64: dts: ti: k3-j721e: Rename mux header and update macro names
soc: qcom: pdr: Fixup array type of get_domain_list_resp message
arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
arm64: dts: sdm630: Temporarily disable SMMUs by default
arm64: dts: sdm845: Fixup OPP table for all qup devices
arm64: dts: allwinner: h5: remove Mali GPU PMU module
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
soc: xilinx: Fix error code in zynqmp_pm_probe()
Vitaly Kuznetsov [Sat, 24 Oct 2020 08:13:24 +0000 (04:13 -0400)]
KVM: ioapic: break infinite recursion on lazy EOI
During shutdown the IOAPIC trigger mode is reset to edge triggered
while the vfio-pci INTx is still registered with a resampler.
This allows us to get into an infinite loop:
ioapic_set_irq
-> ioapic_lazy_update_eoi
-> kvm_ioapic_update_eoi_one
-> kvm_notify_acked_irq
-> kvm_notify_acked_gsi
-> (via irq_acked fn ptr) irqfd_resampler_ack
-> kvm_set_irq
-> (via set fn ptr) kvm_set_ioapic_irq
-> kvm_ioapic_set_irq
-> ioapic_set_irq
Commit
8be8f932e3db ("kvm: ioapic: Restrict lazy EOI update to
edge-triggered interrupts", 2020-05-04) acknowledges that this recursion
loop exists and tries to avoid it at the call to ioapic_lazy_update_eoi,
but at this point the scenario is already set, we have an edge interrupt
with resampler on the same gsi.
Fortunately, the only user of irq ack notifiers (in addition to resamplefd)
is i8254 timer interrupt reinjection. These are edge-triggered, so in
principle they would need the call to kvm_ioapic_update_eoi_one from
ioapic_lazy_update_eoi, but they already disable AVIC(*), so they don't
need the lazy EOI behavior. Therefore, remove the call to
kvm_ioapic_update_eoi_one from ioapic_lazy_update_eoi.
This fixes CVE-2020-27152. Note that this issue cannot happen with
SR-IOV assigned devices because virtual functions do not have INTx,
only MSI.
Fixes:
f458d039db7e ("kvm: ioapic: Lazy update IOAPIC EOI")
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Paolo Bonzini [Sat, 24 Oct 2020 08:08:37 +0000 (04:08 -0400)]
KVM: vmx: rename pi_init to avoid conflict with paride
allyesconfig results in:
ld: drivers/block/paride/paride.o: in function `pi_init':
(.text+0x1340): multiple definition of `pi_init'; arch/x86/kvm/vmx/posted_intr.o:posted_intr.c:(.init.text+0x0): first defined here
make: *** [Makefile:1164: vmlinux] Error 1
because commit:
commit
8888cdd0996c2d51cd417f9a60a282c034f3fa28
Author: Xiaoyao Li <xiaoyao.li@intel.com>
Date: Wed Sep 23 11:31:11 2020 -0700
KVM: VMX: Extract posted interrupt support to separate files
added another pi_init(), though one already existed in the paride code.
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sean Christopherson [Sat, 24 Oct 2020 03:11:50 +0000 (20:11 -0700)]
KVM: x86/mmu: Avoid modulo operator on 64-bit value to fix i386 build
Replace a modulo operator with the more common pattern for computing the
gfn "offset" of a huge page to fix an i386 build error.
arch/x86/kvm/mmu/tdp_mmu.c:212: undefined reference to `__umoddi3'
In fact, almost all of tdp_mmu.c can be elided on 32-bit builds, but
that is a much larger patch.
Fixes:
2f2fad0897cb ("kvm: x86/mmu: Add functions to handle changed TDP SPTEs")
Reported-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Message-Id: <
20201024031150.9318-1-sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Steve French [Mon, 28 Sep 2020 03:43:22 +0000 (22:43 -0500)]
cifs: update internal module version number
To 2.29
Signed-off-by: Steve French <stfrench@microsoft.com>
Linus Torvalds [Sat, 24 Oct 2020 00:15:06 +0000 (17:15 -0700)]
Merge tag 'xfs-5.10-merge-7' of git://git./fs/xfs/xfs-linux
Pull xfs fixes from Darrick Wong:
"Two bug fixes that trickled in during the merge window:
- Make fallocate check the alignment of its arguments against the
fundamental allocation unit of the volume the file lives on, so
that we don't trigger the fs' alignment checks.
- Cancel unprocessed log intents immediately when log recovery fails,
to avoid a log deadlock"
* tag 'xfs-5.10-merge-7' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: cancel intents immediately if process_intents fails
xfs: fix fallocate functions when rtextsize is larger than 1
Linus Torvalds [Sat, 24 Oct 2020 00:13:53 +0000 (17:13 -0700)]
Merge tag 'docs-5.10-2' of git://git.lwn.net/linux
Pull documentation fixes from Jonathan Corbet:
"A handful of late-arriving documentation fixes"
* tag 'docs-5.10-2' of git://git.lwn.net/linux:
docs: Add two missing entries in vm sysctl index
docs/vm: trivial fixes to several spelling mistakes
docs: submitting-patches: describe preserving review/test tags
Documentation: Chinese translation of Documentation/arm64/hugetlbpage.rst
Documentation: x86: fix a missing word in x86_64/mm.rst.
docs: driver-api: remove a duplicated index entry
docs: lkdtm: Modernize and improve details
docs: deprecated.rst: Expand str*cpy() replacement notes
docs/cpu-load: format the example code.
Linus Torvalds [Sat, 24 Oct 2020 00:09:38 +0000 (17:09 -0700)]
Merge tag 'trace-v5.10-3' of git://git./linux/kernel/git/rostedt/linux-trace
Pull tracing ring-buffer fix from Steven Rostedt:
"The success return value of ring_buffer_resize() is stated to be
zero and checked that way.
But it was incorrectly returning the size allocated.
Also, a fix to a comment"
* tag 'trace-v5.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ring-buffer: Update the description for ring_buffer_wait
ring-buffer: Return 0 on success from ring_buffer_resize()
Linus Torvalds [Fri, 23 Oct 2020 23:38:36 +0000 (16:38 -0700)]
Merge tag 'acpi-5.10-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more ACPI updates from Rafael Wysocki:
"These include an ACPICA code build fix related to recent GPE register
access changes, a Kconfig cleanup related to the Dynamic Platform and
Thremal Framework (DPTF) support, a reboot issue workaround, a debug
module fix and a couple of janitorial changes.
Specifics:
- Fix ACPICA code build after recent changes related to accessing GPE
registers (Rafael Wysocki).
- Clean up DPTF part of the ACPI Kconfig (Rafael Wysocki).
- Work around a reboot issue related to RESET_REG (Zhang Rui).
- Prevent ACPI debug module from attemtping to run (and crashing)
when ACPI is disabled (Jamie Iles).
- Drop confusing comment from the ACPI processor driver (Alex Hung).
- Drop a few unreachable break statements (Tom Rix)"
* tag 'acpi-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: utils: remove unreachable breaks
ACPICA: Add missing type casts in GPE register access code
ACPI: DPTF: Add ACPI_DPTF Kconfig menu
ACPI: DPTF: Fix participant driver names
ACPI: processor: remove comment regarding string _UID support
ACPI: reboot: Avoid racing after writing to ACPI RESET_REG
ACPI: debug: don't allow debugging when ACPI is disabled
Linus Torvalds [Fri, 23 Oct 2020 23:27:03 +0000 (16:27 -0700)]
Merge tag 'pm-5.10-rc1-2' of git://git./linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"First of all, the adaptive voltage scaling (AVS) drivers go to new
platform-specific locations as planned (this part was reported to have
merge conflicts against the new arm-soc updates in linux-next).
In addition to that, there are some fixes (intel_idle, intel_pstate,
RAPL, acpi_cpufreq), the addition of on/off notifiers and idle state
accounting support to the generic power domains (genpd) code and some
janitorial changes all over.
Specifics:
- Move the AVS drivers to new platform-specific locations and get rid
of the drivers/power/avs directory (Ulf Hansson).
- Add on/off notifiers and idle state accounting support to the
generic power domains (genpd) framework (Ulf Hansson, Lina Iyer).
- Ulf will maintain the PM domain part of cpuidle-psci (Ulf Hansson).
- Make intel_idle disregard ACPI _CST if it cannot use the data
returned by that method (Mel Gorman).
- Modify intel_pstate to avoid leaving useless sysfs directory
structure behind if it cannot be registered (Chen Yu).
- Fix domain detection in the RAPL power capping driver and prevent
it from failing to enumerate the Psys RAPL domain (Zhang Rui).
- Allow acpi-cpufreq to use ACPI _PSD information with Family 19 and
later AMD chips (Wei Huang).
- Update the driver assumptions comment in intel_idle and fix a
kerneldoc comment in the runtime PM framework (Alexander Monakov,
Bean Huo).
- Avoid unnecessary resets of the cached frequency in the schedutil
cpufreq governor to reduce overhead (Wei Wang).
- Clean up the cpufreq core a bit (Viresh Kumar).
- Make assorted minor janitorial changes (Daniel Lezcano, Geert
Uytterhoeven, Hubert Jasudowicz, Tom Rix).
- Clean up and optimize the cpupower utility somewhat (Colin Ian
King, Martin Kaistra)"
* tag 'pm-5.10-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (23 commits)
PM: sleep: remove unreachable break
PM: AVS: Drop the avs directory and the corresponding Kconfig
PM: AVS: qcom-cpr: Move the driver to the qcom specific drivers
PM: runtime: Fix typo in pm_runtime_set_active() helper comment
PM: domains: Fix build error for genpd notifiers
powercap: Fix typo in Kconfig "Plance" -> "Plane"
cpufreq: schedutil: restore cached freq when next_f is not changed
acpi-cpufreq: Honor _PSD table setting on new AMD CPUs
PM: AVS: smartreflex Move driver to soc specific drivers
PM: AVS: rockchip-io: Move the driver to the rockchip specific drivers
PM: domains: enable domain idle state accounting
PM: domains: Add curly braces to delimit comment + statement block
PM: domains: Add support for PM domain on/off notifiers for genpd
powercap/intel_rapl: enumerate Psys RAPL domain together with package RAPL domain
powercap/intel_rapl: Fix domain detection
intel_idle: Ignore _CST if control cannot be taken from the platform
cpuidle: Remove pointless stub
intel_idle: mention assumption that WBINVD is not needed
MAINTAINERS: Add section for cpuidle-psci PM domain
cpufreq: intel_pstate: Delete intel_pstate sysfs if failed to register the driver
...
Linus Torvalds [Fri, 23 Oct 2020 23:19:02 +0000 (16:19 -0700)]
Merge tag 'scsi-misc' of git://git./linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"The set of core changes here is Christoph's submission path cleanups.
These introduced a couple of regressions when first proposed so they
got held over from the initial merge window pull request to give more
testing time, which they've now had and Syzbot has confirmed the
regression it detected is fixed.
The other main changes are two driver updates (arcmsr, pm80xx) and
assorted minor clean ups"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (38 commits)
scsi: qla2xxx: Fix return of uninitialized value in rval
scsi: core: Set sc_data_direction to DMA_NONE for no-transfer commands
scsi: sr: Initialize ->cmd_len
scsi: arcmsr: Update driver version to v1.50.00.02-
20200819
scsi: arcmsr: Add support for ARC-1886 series RAID controllers
scsi: arcmsr: Fix device hot-plug monitoring timer stop
scsi: arcmsr: Remove unnecessary syntax
scsi: pm80xx: Driver version update
scsi: pm80xx: Increase the number of outstanding I/O supported to 1024
scsi: pm80xx: Remove DMA memory allocation for ccb and device structures
scsi: pm80xx: Increase number of supported queues
scsi: sym53c8xx_2: Fix sizeof() mismatch
scsi: isci: Fix a typo in a comment
scsi: qla4xxx: Fix inconsistent format argument type
scsi: myrb: Fix inconsistent format argument types
scsi: myrb: Remove redundant assignment to variable timeout
scsi: bfa: Fix error return in bfad_pci_init()
scsi: fcoe: Simplify the return expression of fcoe_sysfs_setup()
scsi: snic: Simplify the return expression of svnic_cq_alloc()
scsi: fnic: Simplify the return expression of vnic_wq_copy_alloc()
...
Linus Torvalds [Fri, 23 Oct 2020 23:16:31 +0000 (16:16 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a new driver for ADC driven joysticks
- a new Zintix touchscreen driver
- enhancements to Intel SoC button array driver
- support for F3A "function" in Synaptics RMI4 driver
- assorted driver fixups
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: Add MAINTAINERS entry for SiS i2c touch input driver
Input: evdev - per-client waitgroups
Input: synaptics - enable InterTouch for ThinkPad T14 Gen 1
Input: synaptics - enable InterTouch for ThinkPad P1/X1E gen 2
Input: synaptics-rmi4 - support bootloader v8 in f34v7
Input: synaptics-rmi4 - add support for F3A
Input: synaptics-rmi4 - rename f30_data to gpio_data
Input: add zinitix touchscreen driver
dt-bindings: input/touchscreen: add bindings for zinitix
Input: joystick - add ADC attached joystick driver.
dt-bindings: input: Add docs for ADC driven joystick
Input: sun4i-ps2 - fix handling of platform_get_irq() error
Input: twl4030_keypad - fix handling of platform_get_irq() error
Input: omap4-keypad - fix handling of platform_get_irq() error
Input: ep93xx_keypad - fix handling of platform_get_irq() error
Input: stmfts - fix a & vs && typo
Input: imx6ul_tsc - unify open/close and PM paths
Input: imx6ul_tsc - clean up some errors in imx6ul_tsc_resume()
Input: elants_i2c - fix typo for an attribute to show calibration count
Input: elants_i2c - report resolution of ABS_MT_TOUCH_MAJOR by FW information.
...
Linus Torvalds [Fri, 23 Oct 2020 20:59:05 +0000 (13:59 -0700)]
Merge tag 'sound-fix-5.10-rc1' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few additional small and trivial fixes"
* tag 'sound-fix-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix the return value if cb func is already registered
ALSA: usb-audio: Line6 Pod Go interface requires static clock rate quirk
ALSA: hda/ca0132: make some const arrays static, makes object smaller
ALSA: sparc: dbri: fix repeated word 'the'
Linus Torvalds [Fri, 23 Oct 2020 20:56:34 +0000 (13:56 -0700)]
Merge tag 'drm-next-2020-10-23' of git://anongit.freedesktop.org/drm/drm
Pull more drm fixes from Dave Airlie:
"This should be the last round of things for rc1, a bunch of i915
fixes, some amdgpu, more font OOB fixes and one ttm fix just found
reading code:
fbcon/fonts:
- Two patches to prevent OOB access
ttm:
- fix for evicition value range check
amdgpu:
- Sienna Cichlid fixes
- MST manager resource leak fix
- GPU reset fix
amdkfd:
- Luxmark fix for Navi1x
i915:
- Tweak initial DPCD backlight.enabled value (Sean)
- Initialize reserved MOCS indices (Ayaz)
- Mark initial fb obj as WT on eLLC machines to avoid rcu lockup (Ville)
- Support parsing of oversize batches (Chris)
- Delay execlists processing for TGL (Chris)
- Use the active reference on the vma during error capture (Chris)
- Widen CSB pointer (Chris)
- Wait for CSB entries on TGL (Chris)
- Fix unwind for scratch page allocation (Chris)
- Exclude low patches of stolen memory (Chris)
- Force VT'd workarounds when running as a guest OS (Chris)
- Drop runtime-pm assert from vpgu io accessors (Chris)"
* tag 'drm-next-2020-10-23' of git://anongit.freedesktop.org/drm/drm: (31 commits)
drm/amdgpu: correct the cu and rb info for sienna cichlid
drm/amd/pm: remove the average clock value in sysfs
drm/amd/pm: fix pp_dpm_fclk
Revert drm/amdgpu: disable sienna chichlid UMC RAS
drm/amd/pm: fix pcie information for sienna cichlid
drm/amdkfd: Use same SQ prefetch setting as amdgpu
drm/amd/swsmu: correct wrong feature bit mapping
drm/amd/psp: Fix sysfs: cannot create duplicate filename
drm/amd/display: Avoid MST manager resource leak.
drm/amd/display: Revert "drm/amd/display: Fix a list corruption"
drm/amdgpu: update golden setting for sienna_cichlid
drm/amd/swsmu: add missing feature map for sienna_cichlid
drm/amdgpu: correct the gpu reset handling for job != NULL case
drm/amdgpu: add rlc iram and dram firmware support
drm/amdgpu: add function to program pbb mode for sienna cichlid
drm/i915: Drop runtime-pm assert from vgpu io accessors
drm/i915: Force VT'd workarounds when running as a guest OS
drm/i915: Exclude low pages (128KiB) of stolen from use
drm/i915/gt: Onion unwind for scratch page allocation failure
drm/ttm: fix eviction valuable range check.
...
Rasmus Villemoes [Fri, 23 Oct 2020 20:31:54 +0000 (22:31 +0200)]
x86/uaccess: fix code generation in put_user()
Quoting https://gcc.gnu.org/onlinedocs/gcc/Local-Register-Variables.html:
You can define a local register variable and associate it with a
specified register...
The only supported use for this feature is to specify registers for
input and output operands when calling Extended asm (see Extended
Asm). This may be necessary if the constraints for a particular
machine don't provide sufficient control to select the desired
register.
On 32-bit x86, this is used to ensure that gcc will put an 8-byte value
into the %edx:%eax pair, while all other cases will just use the single
register %eax (%rax on x86-64). While the _ASM_AX actually just expands
to "%eax", note this comment next to get_user() which does something
very similar:
* The use of _ASM_DX as the register specifier is a bit of a
* simplification, as gcc only cares about it as the starting point
* and not size: for a 64-bit value it will use %ecx:%edx on 32 bits
* (%ecx being the next register in gcc's x86 register sequence), and
* %rdx on 64 bits.
However, getting this to work requires that there is no code between the
assignment to the local register variable and its use as an input to the
asm() which can possibly clobber any of the registers involved -
including evaluation of the expressions making up other inputs.
In the current code, the ptr expression used directly as an input may
cause such code to be emitted. For example, Sean Christopherson
observed that with KASAN enabled and ptr being current->set_child_tid
(from chedule_tail()), the load of current->set_child_tid causes a call
to __asan_load8() to be emitted immediately prior to the __put_user_4
call, and Naresh Kamboju reports that various mmstress tests fail on
KASAN-enabled builds.
It's also possible to synthesize a broken case without KASAN if one uses
"foo()" as the ptr argument, with foo being some "extern u64 __user
*foo(void);" (though I don't know if that appears in real code).
Fix it by making sure ptr gets evaluated before the assignment to
__val_pu, and add a comment that __val_pu must be the last thing
computed before the asm() is entered.
Cc: Sean Christopherson <sean.j.christopherson@intel.com>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Tested-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Fixes:
d55564cfc222 ("x86: Make __put_user() generate an out-of-line call")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Steve French [Fri, 23 Oct 2020 20:21:38 +0000 (15:21 -0500)]
smb3: add some missing definitions from MS-FSCC
Add some structures and defines that were recently added to
the protocol documentation (see MS-FSCC sections 2.3.29-2.3.34).
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Fri, 23 Oct 2020 13:23:45 +0000 (08:23 -0500)]
smb3: remove two unused variables
Fix two unused variables in commit
"add support for stat of WSL reparse points for special file types"
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
Steve French [Fri, 23 Oct 2020 03:03:14 +0000 (22:03 -0500)]
smb3: add support for stat of WSL reparse points for special file types
This is needed so when mounting to Windows we do not
misinterpret various special files created by Linux (WSL) as symlinks.
An earlier patch addressed readdir. This patch fixes stat (getattr).
With this patch:
File: /mnt1/char
Size: 0 Blocks: 0 IO Block: 16384 character special file
Device: 34h/52d Inode:
844424930132069 Links: 1 Device type: 0,0
Access: (0755/crwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2020-10-21 17:46:51.
839458900 -0500
Modify: 2020-10-21 17:46:51.
839458900 -0500
Change: 2020-10-21 18:30:39.
797358800 -0500
Birth: -
File: /mnt1/fifo
Size: 0 Blocks: 0 IO Block: 16384 fifo
Device: 34h/52d Inode:
1125899906842722 Links: 1
Access: (0755/prwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2020-10-21 16:21:37.
259249700 -0500
Modify: 2020-10-21 16:21:37.
259249700 -0500
Change: 2020-10-21 18:30:39.
797358800 -0500
Birth: -
File: /mnt1/block
Size: 0 Blocks: 0 IO Block: 16384 block special file
Device: 34h/52d Inode:
844424930132068 Links: 1 Device type: 0,0
Access: (0755/brwxr-xr-x) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2020-10-21 17:10:47.
913103200 -0500
Modify: 2020-10-21 17:10:47.
913103200 -0500
Change: 2020-10-21 18:30:39.
796725500 -0500
Birth: -
without the patch all show up incorrectly as symlinks with annoying "operation not supported error also returned"
File: /mnt1/charstat: cannot read symbolic link '/mnt1/char': Operation not supported
Size: 0 Blocks: 0 IO Block: 16384 symbolic link
Device: 34h/52d Inode:
844424930132069 Links: 1
Access: (0000/l---------) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2020-10-21 17:46:51.
839458900 -0500
Modify: 2020-10-21 17:46:51.
839458900 -0500
Change: 2020-10-21 18:30:39.
797358800 -0500
Birth: -
File: /mnt1/fifostat: cannot read symbolic link '/mnt1/fifo': Operation not supported
Size: 0 Blocks: 0 IO Block: 16384 symbolic link
Device: 34h/52d Inode:
1125899906842722 Links: 1
Access: (0000/l---------) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2020-10-21 16:21:37.
259249700 -0500
Modify: 2020-10-21 16:21:37.
259249700 -0500
Change: 2020-10-21 18:30:39.
797358800 -0500
Birth: -
File: /mnt1/blockstat: cannot read symbolic link '/mnt1/block': Operation not supported
Size: 0 Blocks: 0 IO Block: 16384 symbolic link
Device: 34h/52d Inode:
844424930132068 Links: 1
Access: (0000/l---------) Uid: ( 0/ root) Gid: ( 0/ root)
Access: 2020-10-21 17:10:47.
913103200 -0500
Modify: 2020-10-21 17:10:47.
913103200 -0500
Change: 2020-10-21 18:30:39.
796725500 -0500
Signed-off-by: Steve French <stfrench@microsoft.com>
Reviewed-by: Ronnie Sahlberg <lsahlber@redhat.com>