Lubomir Popov [Wed, 20 Nov 2013 13:32:17 +0000 (15:32 +0200)]
ARM: OMAP4: Fix bug in omap4470_volts struct
The struct incorrectly referenced SMPS1 for all three power
domains. Fixed this by using SMPS2 and SMPS5 as appropriate.
Add some comments and choose voltage values that correspond
to voltage selection codes.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Lars Poeschel [Tue, 19 Nov 2013 10:22:18 +0000 (11:22 +0100)]
pcm051: Support for revision 3
Phytec sells revision or version 3 of pcm051. It is labeled 1358.3 on
the board. The difference for u-boot is that is has other DDR3 RAM on it:
1 x MT41K256M16HA125E instead of 2 x MT41J256M8HX15E on revisions 1 and
2. Both configurations are 512 MiB.
Configure your u-boot build with pcm051_rev3 for the new RAM and
pcm051_rev1 for the old RAM configuration. Board revision 2 has to use
pcm051_rev1 also.
Signed-off-by: Lars Poeschel <poeschel@lemonage.de>
Ilya Ledvich [Thu, 7 Nov 2013 05:57:35 +0000 (07:57 +0200)]
cm_t335: add support for pca9555 i2c gpio extender
Add support for the 16 bits pca9555 i2c to gpio extender featured
by the SB-T335 baseboard.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Ilya Ledvich [Thu, 7 Nov 2013 05:57:34 +0000 (07:57 +0200)]
cm_t335: add support for status LED
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Ilya Ledvich [Thu, 7 Nov 2013 05:57:33 +0000 (07:57 +0200)]
cm_t335: add cm_t335 board support
Add cm_t335 board directory, config file. Enable build.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
[trini: Adapt Makefile]
Signed-off-by: Tom Rini <trini@ti.com>
Chin Liang See [Mon, 2 Dec 2013 18:01:39 +0000 (12:01 -0600)]
socfpga: Adding Freeze Controller driver
Adding Freeze Controller driver. All HPS IOs need to be
in freeze state during pin mux or IO buffer configuration.
It is to avoid any glitch which might happen
during the configuration from propagating to external devices.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Piotr Wilczek [Wed, 27 Nov 2013 10:11:02 +0000 (11:11 +0100)]
board: trats2: update Tizen partition definitions
This patch updates Tizen partions layout.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Wed, 27 Nov 2013 10:11:01 +0000 (11:11 +0100)]
board: trats2: fix access to samsung registers
This patch use 'samsung_get_base' common functions to access registers.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Wed, 27 Nov 2013 10:11:00 +0000 (11:11 +0100)]
board: trats2: fix environmental variables
In this patch variable names are used instead of hardcoded names
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Wed, 27 Nov 2013 10:10:59 +0000 (11:10 +0100)]
board: trats2: remove unused defines from config file
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Rajeshwari Shinde [Tue, 8 Oct 2013 13:12:22 +0000 (18:42 +0530)]
exynos: spl: Add a custom spi copy function
This patch implements a custom spi_copy funtion to copy u-boot from SF
to RAM. This is faster then iROM spi_copy funtion as this runs spi at
50Mhz and also in WORD mode of operation.
Changed a printf in pinmux.c to debug just to avoid the compilation
error in SPL.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Nobuhiro Iwamatsu [Thu, 28 Nov 2013 08:52:47 +0000 (17:52 +0900)]
arm: rmobile: Remove config.mk
Renesas ARM SoCs (R-Mobile, R-Car) are armv7 only.
This drops armv5 supprt from PLATFORM_CPPFLAGS and remove config.mk of
rmobile.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Nobuhiro Iwamatsu [Thu, 28 Nov 2013 08:52:46 +0000 (17:52 +0900)]
arm: kzm9g: Fix undefined reference to `__aeabi_uldivmod' error
The kzm9g board fails in building with -march=armv7-a.
This fixs this problem by converting to do_div().
-----
USE_PRIVATE_LIBGCC=yes ./MAKEALL kzm9g
...
arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_us':
arch/arm/cpu/armv7/rmobile/timer.c:41: undefined reference to `__aeabi_uldivmod'
arch/arm/cpu/armv7/rmobile/librmobile.o: In function `get_time_ms':
arch/arm/cpu/armv7/rmobile/timer.c:47: undefined reference to `__aeabi_uldivmod'
-----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Nobuhiro Iwamatsu [Thu, 21 Nov 2013 08:07:46 +0000 (17:07 +0900)]
arm: rmobile: Add support koelsch board
The koelsch board has R8A7791, 2GB DDR3-SDRAM, USB,
Quad SPI, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIF
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Nobuhiro Iwamatsu [Thu, 21 Nov 2013 08:07:45 +0000 (17:07 +0900)]
arm: rmobile: Add support R8A7791
Renesas R8A7791 is CPU with Cortex-A15.
This supports the basic register definition and GPIO and
framework of PFC.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Nobuhiro Iwamatsu [Thu, 21 Nov 2013 08:06:46 +0000 (17:06 +0900)]
arm: rmobile: Add support lager board
The lager board has R8A7790, 4GB DDR3-SDRAM, USB, Ethernet, and more.
This patch supports the following functions:
- DDR3-SDRAM
- SCIF
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Nobuhiro Iwamatsu [Thu, 21 Nov 2013 08:06:45 +0000 (17:06 +0900)]
arm: rmobile: Add support R8A7790
Renesas R8A7790 is CPU with Cortex-A7 and A15.
This supports the basic register definition and GPIO and
framework of PFC.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Nobuhiro Iwamatsu [Thu, 21 Nov 2013 08:06:44 +0000 (17:06 +0900)]
arm: rmobile: Move lowlevel_init.o to taget of each CPU
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Minkyu Kang [Fri, 29 Nov 2013 01:02:34 +0000 (10:02 +0900)]
arm: exynos: fix the align for exynos4_power structure
res3 should be 4bytes
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dominik Klein <dominik.klein@gmx.com>
Jaehoon Chung [Mon, 2 Dec 2013 05:25:33 +0000 (14:25 +0900)]
arm: exynos: fix set_mmc_clk for exynos4x12
Fix the set_mmc_clk() for exnos4x12.
If board is exynos4x12, mmc clock should be set to wrong value.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Przemyslaw Marczak [Mon, 2 Dec 2013 12:54:01 +0000 (13:54 +0100)]
trats: usb: Add usb_cable_connected() function
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Albert ARIBAUD [Mon, 2 Dec 2013 15:00:10 +0000 (16:00 +0100)]
Merge branch 'u-boot-atmel/master' into 'u-boot-arm/master'
Tom Rini [Mon, 2 Dec 2013 13:48:02 +0000 (08:48 -0500)]
Merge branch 'serial' of git://git.denx.de/u-boot-microblaze
Tom Rini [Mon, 2 Dec 2013 13:44:28 +0000 (08:44 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mips
Masahiro Yamada [Thu, 21 Nov 2013 07:10:20 +0000 (16:10 +0900)]
Blackfin: remove executable permission of AWK script
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tom Rini [Mon, 2 Dec 2013 13:38:28 +0000 (08:38 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx
Soren Brinkmann [Tue, 29 Oct 2013 20:11:54 +0000 (13:11 -0700)]
serial: zynq: Remove unused #defines
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: trini, uboot
Piotr Wilczek [Tue, 12 Nov 2013 14:22:46 +0000 (15:22 +0100)]
trats2: enable dfu and thor protocol for Tizen download
Trats2 config is updated to support DFU mode.
Malloc pool must be increased for DFU buffer allocation.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Thu, 21 Nov 2013 14:46:45 +0000 (15:46 +0100)]
trats2: enable ums support on Trats2
This patch adds support for USB and enables 'ums' command on Trats2 board.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Piotr Wilczek [Thu, 21 Nov 2013 14:46:44 +0000 (15:46 +0100)]
driver:usb:s3c_udc: add support for Exynos4x12
This patch add new defines for usb phy for Exynos4x12.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Jens Scharsig (BuS Elektronik) [Fri, 29 Nov 2013 10:35:16 +0000 (11:35 +0100)]
arm: atmel: eb_cpux9k2: config clean up
* remove mature defines from board config
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Wed, 20 Nov 2013 03:17:16 +0000 (11:17 +0800)]
arm: atmel: sam9m10g45ek: let CONFIG_SYS_NO_FLASH at proper position
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, if the
CONFIG_SYS_NO_FLASH defined later than include/config_cmd_default.h,
These two commands will be included always.
So move CONFIG_SYS_NO_FLASH definition to proper position.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Heiko Schocher [Mon, 18 Nov 2013 07:07:23 +0000 (08:07 +0100)]
arm926ejs, at91: add common phy_reset function
add common phy reset code into a common function.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Jens Scharsig <esw@bus-elektronik.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Stelian Pop <stelian@popies.net>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Markus Hubig <mhubig@imko.de>
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:38 +0000 (11:12 +0800)]
arm: atmel: sama5d3: spl boot from fat fs SD card
Enable Atmel sama5d3xek boart spl boot support, which can load u-boot
from SD card with FAT file system.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:37 +0000 (11:12 +0800)]
arm: atmel: add ddr2 initialization function
The MPDDRC supports different type of SDRAM
This patch add ddr2 initialization function
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:36 +0000 (11:12 +0800)]
arm: atmel: sama5d3: early enable PIO peripherals
Enable the PIO peripherals early than other peripherals.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:35 +0000 (11:12 +0800)]
arm: atmel: sama5d3: the offset of MULA is 18
The offset of MULA field in PLLA register in sama5d3 is 18,
and the length only 7 bits.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:34 +0000 (11:12 +0800)]
arm: atmel: sama5d3: correct the error define of DIV
Correct the error define of DIV.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:33 +0000 (11:12 +0800)]
arm: at91: pm9261: remove undefined bit in mckr
The PLLADIV2 bit is not defined in at91sam9261 SoC, so remove it.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Bo Shen [Fri, 15 Nov 2013 03:12:32 +0000 (11:12 +0800)]
arm: atmel: sama5d3: correct the ID for DBGU and PIT
As the DBGU and PIT has its own ID on sama5d3 SoC, while not share
with SYS ID. So, correct them.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Luka Perkov [Mon, 4 Nov 2013 01:12:00 +0000 (02:12 +0100)]
config: arm: exynos5250: remove duplicate defines
The SPI section is already defined in this file (lines 268-288) so we can
remove the duplicate definitions. While at it, also fix one tiny whitespace
typo.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Paul Burton [Tue, 26 Nov 2013 17:45:28 +0000 (17:45 +0000)]
malta: set CONFIG_SYS_BOOTM_LEN to 64MB
Allow a larger kernel binary to be decompressed - the default 8MB can
become limiting on a Malta.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Tue, 26 Nov 2013 17:45:27 +0000 (17:45 +0000)]
malta: enable PIIX4 SERIRQ
Whilst U-boot does not require this itself, Linux currently relies upon
it having been muxed and enabled by the bootloader. Thus in order to
preserve compatibility with current kernels before a fix is merged in
Linux we will enable the SERIRQ interrupt and mux it to its pin.
Without doing this current kernels will never receive serial port
interrupts and the end result is typically that userland appears to
hang.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Tue, 26 Nov 2013 17:45:26 +0000 (17:45 +0000)]
malta: correct UART baudrate
CONFIG_SYS_NS16550_CLK specifies the rate of the clock 16x the baud
rate. The SMSC FDC37M81x datasheet states that a divider of 1 results in
a UART at 115200 baud, thus the x16 clock rate is 115200 * 16.
Previously the divider was left at 0 which led to a rate of 38400 baud
regardless of CONFIG_BAUDRATE or the baudrate environment variable.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Paul Burton [Tue, 26 Nov 2013 17:45:25 +0000 (17:45 +0000)]
mips: don't hardcode Malta env baudrate
The baudrate passed to Linux in the environment was hardcoded at 38400.
Instead pass the correct baudrate from global data, allowing Linux to
correctly inherit the baudrate used by U-boot when console setup is not
explicitly specified.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Tom Rini [Mon, 25 Nov 2013 21:49:32 +0000 (16:49 -0500)]
Prepare v2014.01-rc1
Signed-off-by: Tom Rini <trini@ti.com>
Shengzhou Liu [Fri, 22 Nov 2013 09:39:12 +0000 (17:39 +0800)]
t2080qds/ramboot: enable PBL tool for t2080qds
Add the default RCW(SerDes 0x66_0x16) and PBI configure file for
T2080QDS board, so we can use PBL tool to generate the ramboot
image to support boot from NAND/SPI/SD.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Shengzhou Liu [Fri, 22 Nov 2013 09:39:11 +0000 (17:39 +0800)]
powerpc/t2080qds: add support for t2080qds board
The T2080QDS is a high-performance computing evaluation, development and
test platform supporting the T2080 QorIQ Power Architecture processor.
T2080QDS feature overview
Processor:
- T2080 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
Memory:
- Single memory controller capable of supporting DDR3 and DDR3-LV devices
- Two DDR3 DIMMs up to 4GB, Dual rank @ 2133MT/s and ECC support
Ethernet interfaces:
- Two 1Gbps RGMII on-board ports
- Four 10Gbps XFI on-board cages
- 1Gbps/2.5Gbps SGMII Riser card
- 10Gbps XAUI Riser card
Accelerator:
- DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
SerDes:
- 16 lanes up to 10.3125GHz
- Supports Aurora debug, PEX, SATA, SGMII, sRIO, HiGig, XFI and XAUI
IFC:
- 128MB NOR Flash, 512MB NAND Flash, PromJet debug port and FPGA
eSPI:
- Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
USB:
- Two USB2.0 ports with internal PHY (one Type-A + one micro Type-AB)
PCIE:
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
SATA:
- Two SATA 2.0 ports on-board
SRIO:
- Two Serial RapidIO 2.0 ports up to 5 GHz
eSDHC:
- Supports SD/SDHC/SDXC/eMMC Card
I2C:
- Four I2C controllers.
UART:
- Dual 4-pins UART serial ports
System Logic:
- QIXIS-II FPGA system controll
Debug Features:
- Support Legacy, COP/JTAG, Aurora, Event and EVT
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: removed Makefile blank line at EOF,
fix conflicts with moving DDR driver]
Acked-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 22 Nov 2013 09:39:10 +0000 (17:39 +0800)]
powerpc/mpc85xx: Add T2080/T2081 SoC support
Add support for Freescale T2080/T2081 SoC.
T2080 includes the following functions and features:
- Four dual-threads 64-bit Power architecture e6500 cores, up to 1.8GHz
- 2MB L2 cache and 512KB CoreNet platform cache (CPC)
- Hierarchical interconnect fabric
- One 32-/64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- 16 SerDes lanes up to 10.3125 GHz
- 8 mEMACs for network interfaces (four 1Gbps MACs and four 10Gbps/1Gbps MACs)
- High-speed peripheral interfaces
- Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz
- Additional peripheral interfaces
- Two serial ATA (SATA 2.0) controllers
- Two high-speed USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/SDHC/SDXC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Three eight-channel DMA engines
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T2080 and T2081:
Feature T2080 T2081
1G Ethernet numbers: 8 6
10G Ethernet numbers: 4 2
SerDes lanes: 16 8
Serial RapidIO,RMan: 2 no
SATA Controller: 2 no
Aurora: yes no
SoC Package: 896-pins 780-pins
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Shengzhou Liu [Fri, 22 Nov 2013 09:39:09 +0000 (17:39 +0800)]
net/fman: Add support for 10GEC3 and 10GEC4
There are more than two 10GEC in single FMAN in some SoCs(e.g. T2080).
This patch adds support for 10GEC3 and 10GEC4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
York Sun [Tue, 22 Oct 2013 19:39:02 +0000 (12:39 -0700)]
Driver/IFC: Move Freescale IFC driver to a common driver
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
York Sun [Mon, 28 Oct 2013 23:36:02 +0000 (16:36 -0700)]
Driver/DDR: Update DDR driver to allow non-zero base address
The DRAM base has been zero for Power SoCs. It could be non-zero
for ARM SoCs. Use a macro instead of hard-coding to zero.
Signed-off-by: York Sun <yorksun@freescale.com>
York Sun [Mon, 3 Jun 2013 19:39:06 +0000 (12:39 -0700)]
powerpc/mpc8xxx: Extend DDR registers' fields
Some DDR registers' fields have expanded to accommodate larger values.
These changes are backward compatible. Some fields are removed for newer
DDR controllers. Writing to those fields are safely ignored.
TIMING_CFG_2 register is fixed. Additive latency is added to RD_TO_PRE
automatically. It was a misunderstanding in commit
c360ceac.
Signed-off-by: York Sun <yorksun@freescale.com>
York Sun [Mon, 30 Sep 2013 21:20:51 +0000 (14:20 -0700)]
Driver/DDR: Add Freescale DDR driver for ARM
Make PowerPC specific code conditional so ARM SoCs can reuse
this driver. Add DDR3 driver for ARM.
Signed-off-by: York Sun <yorksun@freescale.com>
York Sun [Mon, 18 Nov 2013 18:29:32 +0000 (10:29 -0800)]
Driver/DDR: combine ccsr_ddr for 83xx, 85xx and 86xx
Fix ccsr_ddr structure to avoid using typedef. Combine DDR2 and DDR3
structure for 83xx, 85xx and 86xx.
Signed-off-by: York Sun <yorksun@freescale.com>
York Sun [Mon, 30 Sep 2013 16:22:09 +0000 (09:22 -0700)]
Driver/DDR: Moving Freescale DDR driver to a common driver
Freescale DDR driver has been used for mpc83xx, mpc85xx, mpc86xx SoCs.
The similar DDR controllers will be used for ARM-based SoCs.
Signed-off-by: York Sun <yorksun@freescale.com>
Zhao Qiang [Thu, 26 Sep 2013 01:10:32 +0000 (09:10 +0800)]
p1010rdb: enable mtdparts for NAND
The default partition table matches the .dts files for these boards in
Linux. This allows these partitions to be used by name with U-Boot's
"nand" command.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Tang Yuantian [Thu, 17 Oct 2013 02:47:33 +0000 (10:47 +0800)]
mpc85xx: Fix the offset of register address error
The offset of register address within GPIO module is just
CONFIG_SYS_MPC85xx_GPIO_ADDR. So, fix it. The following platforms
are confirmed: MPC8572, P1023, P1020, P1022, P2020, P4080,
P5020, P5040, T4240, B4860.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Priyanka Jain [Fri, 25 Oct 2013 09:56:27 +0000 (15:26 +0530)]
powerpc/t1040qds: Correct Maintainer name in boards.cfg
Update T1040QDS naem to Poonam Aggrwal.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Tom Rini [Mon, 25 Nov 2013 15:42:53 +0000 (10:42 -0500)]
Merge branch 'sandbox1' of git.denx.de/u-boot-x86
Tom Rini [Mon, 25 Nov 2013 15:42:19 +0000 (10:42 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-net
Tom Rini [Mon, 25 Nov 2013 15:42:13 +0000 (10:42 -0500)]
Merge branch 'master' of git://git.denx.de/u-boot-nand-flash
Tom Rini [Mon, 25 Nov 2013 15:42:05 +0000 (10:42 -0500)]
Merge branch 'buildpatman' of git.denx.de/u-boot-x86
Tom Rini [Mon, 18 Nov 2013 13:31:56 +0000 (08:31 -0500)]
sparc: Correct arch/sparc/cpu/leon3/start.S from SPDX conversion
The SPDX tag conversion ate part of this file, put things back to the
way they should be.
Signed-off-by: Tom Rini <trini@ti.com>
Wolfgang Denk [Tue, 19 Nov 2013 07:01:44 +0000 (08:01 +0100)]
blackfin: don't use 'bool' when it causes problems
The use of 'bool' data types in globally used header files cases build
errors like this:
In file included from arch/blackfin/include/asm/blackfin.h:13:0,
from include/common.h:92,
from cmd_test.c:17:
arch/blackfin/include/asm/blackfin_local.h:54:1: error: unknown type name 'bool'
Use plain 'int' instead to avoid such kind of trouble.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Masahiro Yamada [Thu, 21 Nov 2013 10:06:58 +0000 (19:06 +0900)]
MAKEALL: add -b (--board) option
Some board have multiple configurations.
For example, the board "m54455evb" has many configurations:
M54455EVB, M54455EVB_a66, M54455EVB_i66, M54455EVB_intel, ...
When we modify board-related files, we need to test
all configurations based on such a board.
In such a case, the new option -b is useful.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 20 Nov 2013 09:14:23 +0000 (18:14 +0900)]
bios_emulator: delete an unnecessary include path
-I$(TOPDIR)/include is defined in the top config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 20 Nov 2013 09:11:57 +0000 (18:11 +0900)]
nand_spl: trivial refactoring of makefiles
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Wed, 20 Nov 2013 03:45:56 +0000 (12:45 +0900)]
Makefile: descend into subdirectories only when CONFIG_API is defined
All objects under api/ and examples/api/ directories are selected
by CONFIG_API.
So we can move CONFIG_API switch to the top Makefile.
In order to use CONFIG_API, the definition of SUBDIR_EXAMPLES-y
must be moved after "sinlude $(obj)include/autoconf.mk".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 07:24:58 +0000 (16:24 +0900)]
common: Delete unnecessary rules.
The directory tools/ is always built before common/.
So when envcrc tool is necessary in common/Makefile,
it already exists.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 02:18:57 +0000 (11:18 +0900)]
drivers: delete unnecessary HOSTCFLAGS
HOSTCFLAGS is meaningless because no host programs
are compiled there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 02:17:30 +0000 (11:17 +0900)]
Makefile: move some libraries to lib/Makefile
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 02:08:35 +0000 (11:08 +0900)]
Makefile: descend into subdirectories only when CONFIG_API is defined
All objects under api/ and examples/api/ directories are selected
by CONFIG_API.
So we can move CONFIG_API switch to the top Makefile.
In order to use CONFIG_API, the definition of SUBDIR_EXAMPLES-y
must be moved after "sinlude $(obj)include/autoconf.mk".
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 02:06:00 +0000 (11:06 +0900)]
examples: delete unnecessary CPPFLAGS
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 01:39:39 +0000 (10:39 +0900)]
board: tqm5200: delete its own object make rule
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 01:34:36 +0000 (10:34 +0900)]
spieval: Remove remainders of dead board
Commit
69434e4c deleted spieval board support
but it missed to clean up include/configs/spieval.h file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 01:25:41 +0000 (10:25 +0900)]
post: remove unnecessary include path settings
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Mon, 18 Nov 2013 00:44:54 +0000 (09:44 +0900)]
board: h2200: Delete an unnecessary make rule
We have a generic rule to generate .o file from *.S
in $(TOPDIR)/config.mk.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 14 Nov 2013 02:00:30 +0000 (11:00 +0900)]
tools: updater: Remove remainders of dead board
tools/updater needs board/MAI/AmigaOneG3SE board
for compiling.
But AmigaOneG3SE board was already deleted
by Commit 953b7e6.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Masahiro Yamada [Thu, 14 Nov 2013 01:58:56 +0000 (10:58 +0900)]
tools: imls: Remove a broken and unused tool.
It looks like tools/imls/Makefile is invoked from nowhere.
And also it is broken.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Igor Grinberg [Thu, 7 Nov 2013 23:03:52 +0000 (01:03 +0200)]
gpio_led: add support for inverted polarity
Some GPIO connected LEDs have inverted polarity.
Introduce new config option: CONFIG_GPIO_LED_INVERTED_TABLE for the
specifying the inverted GPIO LEDs list and add support for this in the
gpio_led driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
Igor Grinberg [Thu, 7 Nov 2013 23:03:51 +0000 (01:03 +0200)]
gpio_led: check gpio_request() return value
Add a check for the gpio_request() function return value and do not try
to configure the GPIO if the gpio_request() call fails.
Also, print an error message indicating the gpio_request() has failed.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
Igor Grinberg [Thu, 7 Nov 2013 23:03:50 +0000 (01:03 +0200)]
README: document the CONFIG_GPIO_LED symbol
The CONFIG_GPIO_LED symbol does not have any documentation in the README
file. Document the CONFIG_GPIO_LED symbol.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tom Rini [Thu, 7 Nov 2013 12:39:48 +0000 (07:39 -0500)]
hash.c: Correct non-hash subcommand crc32 addr-save support
In the case of not having CONFIG_CMD_HASH but having CONFIG_CMD_CRC32
enabled (and not CONFIG_CRC32_VERIFY), we end up in this part of the
code path on hash_command(). However, we will only have exactly 3 args
here, and 3 > 3 is false, and we will not try and store the hash at the
address given as arg #3. The next problem however is that we've been
moving argv around so the third value is now in argv[0] not argv[3].
Confirmed on AM335x Beaglebone White.
Signed-off-by: Tom Rini <trini@ti.com>
Thierry Reding [Fri, 20 Sep 2013 14:03:43 +0000 (16:03 +0200)]
net: rtl8169: Add support for RTL8168d/8111d
This chip is compatible with the existing driver, except that it uses
BAR2 instead of BAR1 for the I/O memory region. Using this patch I can
use the PCIe ethernet interface on the CompuLab Trimslice to boot from
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276477
Thierry Reding [Fri, 20 Sep 2013 14:03:42 +0000 (16:03 +0200)]
net: rtl8169: Improve cache maintenance
Instead of directly calling the low-level invalidate_dcache_range() and
flush_cache() functions, provide thin wrappers that take into account
alignment requirements.
While at it, fix a case where the cache was flushed but should have been
invalidated, two cases where the buffer data was flushed instead of the
descriptor and a missing cache invalidation before reading the packet
data that the NIC just wrote to memory.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch: 276474
Srikanth Thokala [Fri, 8 Nov 2013 17:25:48 +0000 (22:55 +0530)]
net: zynq_gem: Add d-cache support
Added d-cache support for zynq_gem.c,
Observed a difference of +0.8 MiB/s when downloading
a file of size of 3007944Bytes.
With d-cache OFF:
----------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
1.3 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
With d-cache ON:
---------------
Filename 'uImage'.
Load address: 0x800
Loading: #################################################################
#################################################################
#################################################################
##########
2.1 MiB/s
done
Bytes transferred = 3007944 (2de5c8 hex)
Changes on zynq_gem for d-cache support:
- Tx and Rx buffers are cache-aligned
- Updated logic for invalidating Rx buffers and flushing Tx buffers.
- Tx and Rx BD's are allocated from non-cacheable region.
(When BDs are cached, we don't see a consistent link)
- Use TX BD status intead of txsr status checks.
Signed-off-by: Srikanth Thokala <sthokal@xilinx.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
David Dueck [Tue, 5 Nov 2013 16:23:03 +0000 (17:23 +0100)]
phy: Use general phy code for smsc lan8720a
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
David Dueck [Tue, 5 Nov 2013 16:23:02 +0000 (17:23 +0100)]
phy: Use supported field during autonegotiation
The current code incorrectly detects gigabit capabilities for some
100Mbit/s phys. (lan8720a)
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
Andrew Ruder [Wed, 23 Oct 2013 00:09:02 +0000 (19:09 -0500)]
net: dm9000: random mac address support
When an unprogrammed EEPROM is attached to a dm9000, the dm9000 will
come up with a invalid MAC address of ff:ff:ff:ff:ff:ff. Add code that
gets enabled if CONFIG_RANDOM_MACADDR is enabled that generates a random
(and valid) locally administered MAC address that allows the system to
network boot until a real MAC address can be configured.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Rojhalat Ibrahim [Mon, 7 Oct 2013 16:30:39 +0000 (18:30 +0200)]
drivers/net/e1000: Introduce CONFIG_E1000_NO_NVM
The e1000 driver expects to always have some kind of non-volatile memory
attached directly to the ethernet controller chip. This means that I would
have to add an additional separate flash chip to my custom board just to
store essentially the MAC address. Since I don't want to do that, this patch
introduces a new config option CONFIG_E1000_NO_NVM. If defined it disables
all accesses to the NVM. I have tested the patch with a 82574 controller.
Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de>
Andrew Ruder [Wed, 23 Oct 2013 00:10:28 +0000 (19:10 -0500)]
net: tftpsrv: Get correct client MAC address
NetServerEther was not being cleared in the tftp server code, so the
destination MAC address would be whatever the last destination MAC
address was.
Scenario:
U-Boot:
dhcp
tftpsrv
Host:
Send device WRQ
Device:
Responds with ACK to dhcp server mac address with
host ip address
By clearing NetServerEther, we force a lookup of the host MAC address
to go with the associated host IP.
Signed-off-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Fabio Estevam [Sat, 2 Nov 2013 18:40:42 +0000 (16:40 -0200)]
net: phy: atheros: Fix masks for AR8035 and AR8021
The masks were ignoring the last 4 bits which didn't allow detection differences
between the ar8031 and ar8035.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Patch: 288018
Chunhe Lan [Fri, 1 Nov 2013 09:17:44 +0000 (17:17 +0800)]
net/phy: Fix the phy id mask of AR8031
The both AR8031 and AR8035 belong to Atheros 803x serial PHY.
So the phy id mask of AR8031 is the same to the phy id mask
of AR8035. The right mask value is 0x4fffff.
This patch has been tested on the P1010 and P1023.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Patch: 287748
Claudiu Manoil [Mon, 30 Sep 2013 09:44:47 +0000 (12:44 +0300)]
net: tsec: Fix mac addr setup portability, cleanup
Fix the 32-bit memory access that is not "endianess safe",
i.e. not giving the desired byte layout for LE cpus:
tempval = *((uint *) (tmpbuf + 4)), where 'char tmpbuf[]'.
Free the stack from rendundant local vars:
tmpbuf[] and i.
Use a portable type (u32) for the 32bit tsec register value
holder: tempval.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Claudiu Manoil [Mon, 30 Sep 2013 09:44:46 +0000 (12:44 +0300)]
net: tsec: Use portable regs type (uint->u32)
Use cross arch portable u32 instead of uint for the
tsec registers. Remove the typedefs for the register
struct definitions in the process. Fix long lines.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Claudiu Manoil [Fri, 4 Oct 2013 16:13:53 +0000 (19:13 +0300)]
net: tsec: Use portable types and accessors for BDs
Currently, the buffer descriptor (BD) fields cannot be
correctly accessed by a little endian processor. This
patch fixes the issue by making the access of BDs to be
portable among different cpu architectures.
Use portable data types for the Rx/Tx buffer descriptor
fields. Use portable I/O accessors to insure that the
big endian BDs are correctly accessed by little endian
cpus too, and to insure proper sync with the H/W.
Removed the redundant RTXBD "volatile" type, as proper
synchronization around BD data accesses is provided by
the I/O accessors now.
The "sparse" tool was also used to verify the correctness
of these changes.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Claudiu Manoil [Mon, 30 Sep 2013 09:44:44 +0000 (12:44 +0300)]
net: tsec: Fix CamelCase issues around BD code
Fix bufPtr and the rxIdx/ txIdx occurrences to
solve the related checkpatch warnings for the
coming patches.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Claudiu Manoil [Mon, 30 Sep 2013 09:44:43 +0000 (12:44 +0300)]
net: fsl_mdio: Fix warnings for __iomem pointers
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers with
__iomem pointers for tsec. E.g.:
fsl_mdio.c:34:19: warning: incorrect type in argument 1 (different
address spaces)
fsl_mdio.c:34:19: expected unsigned int volatile [noderef]
<asn:2>*addr
fsl_mdio.c:34:19: got unsigned int *<noident>
[...]
tsec.c:91:35: warning: incorrect type in argument 1 (different address
spaces)
tsec.c:91:35: expected struct tsec_mii_mng *phyregs
tsec.c:91:35: got struct tsec_mii_mng [noderef] <asn:2>*phyregs_sgmii
[...]
tsec.c:680:19: warning: incorrect type in assignment (different address
spaces)
tsec.c:680:19: expected struct tsec_mii_mng *regs
tsec.c:680:19: got struct tsec_mii_mng [noderef] <asn:2>*<noident>
[...]
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Claudiu Manoil [Mon, 30 Sep 2013 09:44:42 +0000 (12:44 +0300)]
net: tsec: Cleanup tsec regs init and fix __iomem warns
Remove tsec_t typedef. Define macros as getters of
tsec and mdio register memory regions, for consistent
initialization of various 'regs' fields and also to
manage overly long initialization lines.
Use the __iomem address space marker to address sparse
warnings in tsec.c where IO accessors are used, like:
tsec.c:394:19: warning: incorrect type in argument 1 (different
address spaces)
tsec.c:394:19: expected unsigned int volatile [noderef]
<asn:2>*addr
tsec.c:394:19: got unsigned int *<noident>
[...]
Add the __iomem address space marker for the tsec pointers
to struct tsec_mii_mng memory mapped register regions.
This solves the sparse warnings for mixig normal pointers
with __iomem pointers for tsec.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>