Ioana Ciornei [Sun, 1 Nov 2020 12:51:04 +0000 (14:51 +0200)]
net: phy: aquantia: implement generic .handle_interrupt() callback
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:51:03 +0000 (14:51 +0200)]
net: phy: mscc: remove the use of .ack_interrupt()
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Antoine Tenart <atenart@kernel.org>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:51:02 +0000 (14:51 +0200)]
net: phy: mscc: implement generic .handle_interrupt() callback
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Also, remove the .did_interrupt() callback since it's not anymore used.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com> # VSC8514
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:51:01 +0000 (14:51 +0200)]
net: phy: mscc: use phy_trigger_machine() to notify link change
According to the comment describing the phy_mac_interrupt() function, it
it intended to be used by MAC drivers which have noticed a link change
thus its use in the mscc PHY driver is improper and, most probably, was
added just because phy_trigger_machine() was not exported.
Now that we have acces to trigger the link state machine, use directly
the phy_trigger_machine() function to notify a link change detected by
the PHY driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:51:00 +0000 (14:51 +0200)]
net: phy: at803x: remove the use of .ack_interrupt()
In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.
This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:50:59 +0000 (14:50 +0200)]
net: phy: at803x: implement generic .handle_interrupt() callback
In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:50:58 +0000 (14:50 +0200)]
net: phy: make .ack_interrupt() optional
As a first step into making phylib and all PHY drivers to actually
have support for shared IRQs, make the .ack_interrupt() callback
optional.
After all drivers have been moved to implement the generic
interrupt handle, the phy_drv_supports_irq() check will be
changed again to only require the .handle_interrupts() callback.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:50:57 +0000 (14:50 +0200)]
net: phy: add a shutdown procedure
In case of a board which uses a shared IRQ we can easily end up with an
IRQ storm after a forced reboot.
For example, a 'reboot -f' will trigger a call to the .shutdown()
callbacks of all devices. Because phylib does not implement that hook,
the PHY is not quiesced, thus it can very well leave its IRQ enabled.
At the next boot, if that IRQ line is found asserted by the first PHY
driver that uses it, but _before_ the driver that is _actually_ keeping
the shared IRQ asserted is probed, the IRQ is not going to be
acknowledged, thus it will keep being fired preventing the boot process
of the kernel to continue. This is even worse when the second PHY driver
is a module.
To fix this, implement the .shutdown() callback and disable the
interrupts if these are used.
Note that we are still susceptible to IRQ storms if the previous kernel
exited with a panic or if the bootloader left the shared IRQ active, but
there is absolutely nothing we can do about these cases.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei [Sun, 1 Nov 2020 12:50:56 +0000 (14:50 +0200)]
net: phy: export phy_error and phy_trigger_machine
These functions are currently used by phy_interrupt() to either signal
an error condition or to trigger the link state machine. In an attempt
to actually support shared PHY IRQs, export these two functions so that
the actual PHY drivers can use them.
Cc: Alexandru Ardelean <alexandru.ardelean@analog.com>
Cc: Andre Edich <andre.edich@microchip.com>
Cc: Antoine Tenart <atenart@kernel.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Divya Koppera <Divya.Koppera@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Kavya Sree Kotagiri <kavyasree.kotagiri@microchip.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marco Felsch <m.felsch@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Mathias Kresin <dev@kresin.me>
Cc: Maxim Kochetkov <fido_max@inbox.ru>
Cc: Michael Walle <michael@walle.cc>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Nisar Sayed <Nisar.Sayed@microchip.com>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Cc: Willy Liu <willy.liu@realtek.com>
Cc: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Xin Long [Wed, 4 Nov 2020 06:55:32 +0000 (14:55 +0800)]
sctp: bring inet(6)_skb_parm back to sctp_input_cb
inet(6)_skb_parm was removed from sctp_input_cb by Commit
a1dd2cf2f1ae
("sctp: allow changing transport encap_port by peer packets"), as it
thought sctp_input_cb->header is not used any more in SCTP.
syzbot reported a crash:
[ ] BUG: KASAN: use-after-free in decode_session6+0xe7c/0x1580
[ ]
[ ] Call Trace:
[ ] <IRQ>
[ ] dump_stack+0x107/0x163
[ ] kasan_report.cold+0x1f/0x37
[ ] decode_session6+0xe7c/0x1580
[ ] __xfrm_policy_check+0x2fa/0x2850
[ ] sctp_rcv+0x12b0/0x2e30
[ ] sctp6_rcv+0x22/0x40
[ ] ip6_protocol_deliver_rcu+0x2e8/0x1680
[ ] ip6_input_finish+0x7f/0x160
[ ] ip6_input+0x9c/0xd0
[ ] ipv6_rcv+0x28e/0x3c0
It was caused by sctp_input_cb->header/IP6CB(skb) still used in sctp rx
path decode_session6() but some members overwritten by sctp6_rcv().
This patch is to fix it by bring inet(6)_skb_parm back to sctp_input_cb
and not overwriting it in sctp4/6_rcv() and sctp_udp_rcv().
Reported-by: syzbot+5be8aebb1b7dfa90ef31@syzkaller.appspotmail.com
Fixes:
a1dd2cf2f1ae ("sctp: allow changing transport encap_port by peer packets")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/136c1a7a419341487c504be6d1996928d9d16e02.1604472932.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 5 Nov 2020 22:07:51 +0000 (14:07 -0800)]
Merge branch 'hirschmann-hellcreek-dsa-driver'
Kurt Kanzenbach says:
====================
Hirschmann Hellcreek DSA driver
this series adds a DSA driver for the Hirschmann Hellcreek TSN switch
IP. Characteristics of that IP:
* Full duplex Ethernet interface at 100/1000 Mbps on three ports
* IEEE 802.1Q-compliant Ethernet Switch
* IEEE 802.1Qbv Time-Aware scheduling support
* IEEE 1588 and IEEE 802.1AS support
That IP is used e.g. in
https://www.arrow.com/en/campaigns/arrow-kairos
Due to the hardware setup the switch driver is implemented using DSA. A special
tagging protocol is leveraged. Furthermore, this driver supports PTP and
hardware timestamping.
This work is part of the AccessTSN project: https://www.accesstsn.com/
The previous versions can be found here:
* https://lkml.kernel.org/netdev/
20200618064029.32168-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20200710113611.3398-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20200723081714.16005-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20200820081118.10105-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20200901125014.17801-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20200904062739.3540-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20201004112911.25085-1-kurt@linutronix.de/
* https://lkml.kernel.org/netdev/
20201028074221.29326-1-kurt@linutronix.de/
Changes since v7:
* Simplify tagging code (rebase to net-next)
* Pass info instead of ptr (Florian Fainelli)
* Fix yamllint warnings (Rob Herring)
Changes since v6:
* Add .tail_tag = true (Vladimir Oltean)
* Fix vlan_filtering=0 bridges (Vladimir Oltean)
* Enforce restrictions (Vladimir Oltean)
* Sort stuff alphabetically (Vladimir Oltean)
* Rename hellcreek.yaml to hirschmann,hellcreek.yaml
* Typo fixes
Changes since v5:
* Implement configure_vlan_while_not_filtering behavior (Vladimir Oltean)
* Minor cleanups
Changes since v4:
* Fix W=1 compiler warnings (kernel test robot)
* Add tags
Changes since v3:
* Drop TAPRIO support (David Miller)
=> Switch to mutexes due to the lack of hrtimers
* Use more specific compatible strings and add platform data (Andrew Lunn)
* Fix Kconfig ordering (Andrew Lunn)
Changes since v2:
* Make it compile by getting all requirements merged first (Jakub Kicinski, David Miller)
* Use "tsn" for TSN register set (Rob Herring)
* Fix DT binding issues (Rob Herring)
Changes since v1:
* Code simplifications (Florian Fainelli, Vladimir Oltean)
* Fix issues with hellcreek.yaml bindings (Florian Fainelli)
* Clear reserved field in ptp v2 event messages (Richard Cochran)
* Make use of generic ptp parsing function (Richard Cochran, Vladimir Oltean)
* Fix Kconfig (Florian Fainelli)
* Add tags (Florian Fainelli, Rob Herring, Richard Cochran)
Changes since RFC ordered by reviewers:
* Andrew Lunn
* Use dev_dbg for debug messages
* Get rid of __ function names where possible
* Use reverse xmas tree variable ordering
* Remove redundant/useless checks
* Improve comments e.g. for PTP
* Fix Kconfig ordering
* Make LED handling more generic and provide info via DT
* Setup advertisement of PHYs according to hardware
* Drop debugfs patch
* Jakub Kicinski
* Fix compiler warnings
* Florian Fainelli
* Switch to YAML DT bindings
* Richard Cochran
* Fix typo
* Add missing NULL checks
====================
Link: https://lore.kernel.org/r/20201103071101.3222-1-kurt@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kurt Kanzenbach [Tue, 3 Nov 2020 07:11:01 +0000 (08:11 +0100)]
dt-bindings: net: dsa: Add documentation for Hellcreek switches
Add basic documentation and example.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kurt Kanzenbach [Tue, 3 Nov 2020 07:11:00 +0000 (08:11 +0100)]
dt-bindings: Add vendor prefix for Hirschmann
Hirschmann is building devices for automation and networking. Add them to the
vendor prefixes.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kurt Kanzenbach [Tue, 3 Nov 2020 07:10:59 +0000 (08:10 +0100)]
net: dsa: hellcreek: Add PTP status LEDs
The switch has two controllable I/Os which are usually connected to LEDs. This
is useful to immediately visually see the PTP status.
These provide two signals:
* is_gm
This LED can be activated if the current device is the grand master in that
PTP domain.
* sync_good
This LED can be activated if the current device is in sync with the network
time.
Expose these via the LED framework to be controlled via user space
e.g. linuxptp.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kamil Alkhouri [Tue, 3 Nov 2020 07:10:58 +0000 (08:10 +0100)]
net: dsa: hellcreek: Add support for hardware timestamping
The switch has the ability to take hardware generated time stamps per port for
PTPv2 event messages in Rx and Tx direction. That is useful for achieving needed
time synchronization precision for TSN devices/switches. So add support for it.
There are two directions:
* RX
The switch has a single register per port to capture a timestamp. That
mechanism is not used due to correlation problems. If the software processing
is too slow and a PTPv2 event message is received before the previous one has
been processed, false timestamps will be captured. Therefore, the switch can
do "inline" timestamping which means it can insert the nanoseconds part of
the timestamp directly into the PTPv2 event message. The reserved field (4
bytes) is leveraged for that. This might not be in accordance with (older)
PTP standards, but is the only way to get reliable results.
* TX
In Tx direction there is no correlation problem, because the software and the
driver has to ensure that only one event message is "on the fly". However,
the switch provides also a mechanism to check whether a timestamp is
lost. That can only happen when a timestamp is read and at this point another
message is timestamped. So, that lost bit is checked just in case to indicate
to the user that the driver or the software is somewhat buggy.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kamil Alkhouri [Tue, 3 Nov 2020 07:10:57 +0000 (08:10 +0100)]
net: dsa: hellcreek: Add PTP clock support
The switch has internal PTP hardware clocks. Add support for it. There are three
clocks:
* Synchronized
* Syntonized
* Free running
Currently the synchronized clock is exported to user space which is a good
default for the beginning. The free running clock might be exported later
e.g. for implementing 802.1AS-2011/2020 Time Aware Bridges (TAB). The switch
also supports cross time stamping for that purpose.
The implementation adds support setting/getting the time as well as offset and
frequency adjustments. However, the clock only holds a partial timeofday
timestamp. This is why we track the seconds completely in software (see overflow
work and last_ts).
Furthermore, add the PTP multicast addresses into the FDB to forward that
packages only to the CPU port where they are processed by a PTP program.
Signed-off-by: Kamil Alkhouri <kamil.alkhouri@hs-offenburg.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kurt Kanzenbach [Tue, 3 Nov 2020 07:10:56 +0000 (08:10 +0100)]
net: dsa: Add DSA driver for Hirschmann Hellcreek switches
Add a basic DSA driver for Hirschmann Hellcreek switches. Those switches are
implementing features needed for Time Sensitive Networking (TSN) such as support
for the Time Precision Protocol and various shapers like the Time Aware Shaper.
This driver includes basic support for networking:
* VLAN handling
* FDB handling
* Port statistics
* STP
* Phylink
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vladimir Oltean [Tue, 3 Nov 2020 07:10:55 +0000 (08:10 +0100)]
net: dsa: Give drivers the chance to veto certain upper devices
Some switches rely on unique pvids to ensure port separation in
standalone mode, because they don't have a port forwarding matrix
configurable in hardware. So, setups like a group of 2 uppers with the
same VLAN, swp0.100 and swp1.100, will cause traffic tagged with VLAN
100 to be autonomously forwarded between these switch ports, in spite
of there being no bridge between swp0 and swp1.
These drivers need to prevent this from happening. They need to have
VLAN filtering enabled in standalone mode (so they'll drop frames tagged
with unknown VLANs) and they can only accept an 8021q upper on a port as
long as it isn't installed on any other port too. So give them the
chance to veto bad user requests.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
[Kurt: Pass info instead of ptr]
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kurt Kanzenbach [Tue, 3 Nov 2020 07:10:54 +0000 (08:10 +0100)]
net: dsa: Add tag handling for Hirschmann Hellcreek switches
The Hirschmann Hellcreek TSN switches have a special tagging protocol for frames
exchanged between the CPU port and the master interface. The format is a one
byte trailer indicating the destination or origin port.
It's quite similar to the Micrel KSZ tagging. That's why the implementation is
based on that code.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vlad Buslov [Mon, 2 Nov 2020 20:12:43 +0000 (22:12 +0200)]
net: sched: implement action-specific terse dump
Allow user to request action terse dump with new flag value
TCA_FLAG_TERSE_DUMP. Only output essential action info in terse dump (kind,
stats, index and cookie, if set by the user when creating the action). This
is different from filter terse dump where index is excluded (filter can be
identified by its own handle).
Move tcf_action_dump_terse() function to the beginning of source file in
order to call it from tcf_dump_walker().
Signed-off-by: Vlad Buslov <vlad@buslov.dev>
Suggested-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Link: https://lore.kernel.org/r/20201102201243.287486-1-vlad@buslov.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 5 Nov 2020 02:05:56 +0000 (18:05 -0800)]
Merge git://git./linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
1) Move existing bridge packet reject infra to nf_reject_{ipv4,ipv6}.c
from Jose M. Guisado.
2) Consolidate nft_reject_inet initialization and dump, also from Jose.
3) Add the netdev reject action, from Jose.
4) Allow to combine the exist flag and the destroy command in ipset,
from Joszef Kadlecsik.
5) Expose bucket size parameter for hashtables, also from Jozsef.
6) Expose the init value for reproducible ipset listings, from Jozsef.
7) Use __printf attribute in nft_request_module, from Andrew Lunn.
8) Allow to use reject from the inet ingress chain.
* git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next:
netfilter: nft_reject_inet: allow to use reject from inet ingress
netfilter: nftables: Add __printf() attribute
netfilter: ipset: Expose the initval hash parameter to userspace
netfilter: ipset: Add bucketsize parameter to all hash types
netfilter: ipset: Support the -exist flag with the destroy command
netfilter: nft_reject: add reject verdict support for netdev
netfilter: nft_reject: unify reject init and dump into nft_reject
netfilter: nf_reject: add reject skbuff creation helpers
====================
Link: https://lore.kernel.org/r/20201104141149.30082-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 5 Nov 2020 01:45:55 +0000 (17:45 -0800)]
Merge branch 'mptcp-miscellaneous-mptcp-fixes'
Mat Martineau says:
====================
mptcp: Miscellaneous MPTCP fixes
This is a collection of small fixup and minor enhancement patches that
have accumulated in the MPTCP tree while net-next was closed. These are
prerequisites for larger changes we have queued up.
Patch 1 refines receive buffer autotuning.
Patches 2 and 4 are some minor locking and refactoring changes.
Patch 3 improves GRO and RX coalescing with MPTCP skbs.
Patches 5-7 add a sysctl for tuning ADD_ADDR retransmission timeout,
corresponding test code, and documentation.
v2: Add sysctl documentation and fix signoff tags.
====================
Link: https://lore.kernel.org/r/20201103190509.27416-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Tue, 3 Nov 2020 19:05:09 +0000 (11:05 -0800)]
selftests: mptcp: add ADD_ADDR timeout test case
This patch added the test case for retransmitting ADD_ADDR when timeout
occurs. It set NS1's add_addr_timeout to 1 second, and drop NS2's ADD_ADDR
echo packets.
Here we need to slow down the transfer process of all data to let the
ADD_ADDR suboptions can be retransmitted three times. So we added a new
parameter "speed" for do_transfer, it can be set with fast or slow.
We also added three new optional parameters for run_tests, and dropped
run_remove_tests function.
Since we added the netfilter rules in this test case, we need to update
the "config" file.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Mat Martineau [Tue, 3 Nov 2020 19:05:08 +0000 (11:05 -0800)]
docs: networking: mptcp: Add MPTCP sysctl entries
Describe the two MPTCP sysctls, what the values mean, and the default
settings.
Acked-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Geliang Tang [Tue, 3 Nov 2020 19:05:07 +0000 (11:05 -0800)]
mptcp: add a new sysctl add_addr_timeout
This patch added a new sysctl, named add_addr_timeout, to control the
timeout value (in seconds) of the ADD_ADDR retransmission.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Tue, 3 Nov 2020 19:05:06 +0000 (11:05 -0800)]
mptcp: split mptcp_clean_una function
mptcp_clean_una() will wake writers in case memory could be reclaimed.
When called from mptcp_sendmsg the wakeup code isn't needed.
Move the wakeup to a new helper and then use that from the mptcp worker.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Paolo Abeni [Tue, 3 Nov 2020 19:05:05 +0000 (11:05 -0800)]
tcp: propagate MPTCP skb extensions on xmit splits
When the TCP stack splits a packet on the write queue, the tail
half currently lose the associated skb extensions, and will not
carry the DSM on the wire.
The above does not cause functional problems and is allowed by
the RFC, but interact badly with GRO and RX coalescing, as possible
candidates for aggregation will carry different TCP options.
This change tries to improve the MPTCP behavior, propagating the
skb extensions on split.
Additionally, we must prevent the MPTCP stack from updating the
mapping after the split occur: that will both violate the RFC and
fool the reader.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Tue, 3 Nov 2020 19:05:04 +0000 (11:05 -0800)]
mptcp: use _fast lock version in __mptcp_move_skbs
The function is short and won't sleep, so this can use the _fast version.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Florian Westphal [Tue, 3 Nov 2020 19:05:03 +0000 (11:05 -0800)]
mptcp: adjust mptcp receive buffer limit if subflow has larger one
In addition to tcp autotuning during read, it may also increase the
receive buffer in tcp_clamp_window().
In this case, mptcp should adjust its receive buffer size as well so
it can move all pending skbs from the subflow socket to the mptcp socket.
At this time, TCP can have more skbs ready for processing than what the
mptcp receive buffer size allows.
In the mptcp case, the receive window announced is based on the free
space of the mptcp parent socket instead of the individual subflows.
Following the subflow allows mptcp to grow its receive buffer.
This is especially noticeable for loopback traffic where two skbs are
enough to fill the initial receive window.
In mptcp_data_ready() we do not hold the mptcp socket lock, so modifying
mptcp_sk->sk_rcvbuf is racy. Do it when moving skbs from subflow to
mptcp socket, both sockets are locked in this case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Claudiu Manoil [Tue, 3 Nov 2020 14:02:13 +0000 (16:02 +0200)]
enetc: Remove Tx checksumming offload code
Tx checksumming has been defeatured and completely removed
from the h/w reference manual. Made a little cleanup for the
TSE case as this is complementary code.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://lore.kernel.org/r/20201103140213.3294-1-claudiu.manoil@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Zou Wei [Tue, 3 Nov 2020 12:05:00 +0000 (20:05 +0800)]
dpaa_eth: use false and true for bool variables
Fix coccicheck warnings:
./dpaa_eth.c:2549:2-22: WARNING: Assignment of 0/1 to bool variable
./dpaa_eth.c:2562:2-22: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Acked-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Link: https://lore.kernel.org/r/1604405100-33255-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandru Ardelean [Tue, 3 Nov 2020 07:44:36 +0000 (09:44 +0200)]
net: phy: adin: implement cable-test support
The ADIN1300/ADIN1200 support cable diagnostics using TDR.
The cable fault detection is automatically run on all four pairs looking at
all combinations of pair faults by first putting the PHY in standby (clear
the LINK_EN bit, PHY_CTRL_3 register, Address 0x0017) and then enabling the
diagnostic clock (set the DIAG_CLK_EN bit, PHY_CTRL_1 register, Address
0x0012).
Cable diagnostics can then be run (set the CDIAG_RUN bit in the
CDIAG_RUN register, Address 0xBA1B). The results are reported for each pair
in the cable diagnostics results registers, CDIAG_DTLD_RSLTS_0,
CDIAG_DTLD_RSLTS_1, CDIAG_DTLD_RSLTS_2, and CDIAG_DTLD_RSLTS_3, Address
0xBA1D to Address 0xBA20).
The distance to the first fault for each pair is reported in the cable
fault distance registers, CDIAG_FLT_DIST_0, CDIAG_FLT_DIST_1,
CDIAG_FLT_DIST_2, and CDIAG_FLT_DIST_3, Address 0xBA21 to Address 0xBA24).
This change implements support for this using phylib's cable-test support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201103074436.93790-2-alexandru.ardelean@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexandru Ardelean [Tue, 3 Nov 2020 07:44:35 +0000 (09:44 +0200)]
net: phy: adin: disable diag clock & disable standby mode in config_aneg
When the PHY powers up, the diagnostics clock isn't enabled (bit 2 in
register PHY_CTRL_1 (0x0012)).
Also, the PHY is not in standby mode, so bit 13 in PHY_CTRL_3 (0x0017) is
always set at power up.
The standby mode and the diagnostics clock are both meant to be for the
cable diagnostics feature of the PHY (in phylib this would be equivalent to
the cable-test support), and for the frame-generator feature of the PHY.
In standby mode, the PHY doesn't negotiate links or manage links.
To use the cable diagnostics/test (or frame-generator), the PHY must be
first set in standby mode, so that the link operation doesn't interfere.
Then, the diagnostics clock must be enabled.
For the cable-test feature, when the operation finishes, the PHY goes into
PHY_UP state, and the config_aneg hook is called.
For the ADIN PHY, we need to make sure that during autonegotiation
configuration/setup the PHY is removed from standby mode and the
diagnostics clock is disabled, so that normal operation is resumed.
This change does that by moving the set of the ADIN1300_LINKING_EN bit (2)
in the config_aneg (to disable standby mode).
Previously, this was set in the downshift setup, because the downshift
retry value and the ADIN1300_LINKING_EN are in the same register.
And the ADIN1300_DIAG_CLK_EN bit (13) is cleared, to disable the
diagnostics clock.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201103074436.93790-1-alexandru.ardelean@analog.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 5 Nov 2020 00:55:58 +0000 (16:55 -0800)]
Merge branch 'selftests-net-bridge-add-tests-for-mldv2'
Nikolay Aleksandrov says:
====================
selftests: net: bridge: add tests for MLDv2
This is the second selftests patch-set for the new multicast functionality
which adds tests for the bridge's MLDv2 support. The tests use full
precooked packets which are sent via mausezahn and the resulting state
after each test is checked for proper X,Y sets, (*,G) source list, source
list entry timers, (S,G) existence and flags, packet forwarding and
blocking, exclude group expiration and (*,G) auto-add. The first 3 patches
factor out common functions which are used by IGMPv3 tests in lib.sh and
add support for IPv6 test UDP packet, then patch 4 adds the first test with
the initial MLDv2 setup.
The following new tests are added:
- base case: MLDv2 report ff02::cc is_include
- include -> allow report
- include -> is_include report
- include -> is_exclude report
- include -> to_exclude report
- exclude -> allow report
- exclude -> is_include report
- exclude -> is_exclude report
- exclude -> to_exclude report
- include -> block report
- exclude -> block report
- exclude timeout (move to include + entry deletion)
- S,G port entry automatic add to a *,G,exclude port
The variable names and set notation are the same as per RFC 3810,
for more information check RFC 3810 sections 2.3 and 7.
====================
Link: https://lore.kernel.org/r/20201103172412.1044840-1-razor@blackwall.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:12 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 *,g auto-add
When we have *,G ports in exclude mode and a new S,G,port is added
the kernel has to automatically create an S,G entry for each exclude
port to get proper forwarding.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:11 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 exclude timeout
Test that when a group in exclude mode expires it changes mode to
include and the blocked entries are deleted.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:10 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 exc -> block report
The test checks for the following case:
Router State Report Received New Router State Actions
EXCLUDE (X,Y) BLOCK (A) EXCLUDE (X+(A-Y),Y) (A-X-Y) =
Filter Timer
Send Q(MA,A-Y)
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:09 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 inc -> block report
The test checks for the following case:
Router State Report Received New Router State Actions
INCLUDE (A) BLOCK (B) INCLUDE (A) Send Q(MA,A*B)
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:08 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 exc -> to_exclude report
The test checks for the following case:
Router State Report Received New Router State Actions
EXCLUDE (X,Y) TO_EX (A) EXCLUDE (A-Y,Y*A) (A-X-Y) =
Filter Timer
Delete (X-A)
Delete (Y-A)
Send Q(MA,A-Y)
Filter Timer=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:07 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 exc -> is_exclude report
The test checks for the following case:
Router State Report Received New Router State Actions
EXCLUDE (X,Y) IS_EX (A) EXCLUDE (A-Y, Y*A) (A-X-Y)=MALI
Delete (X-A)
Delete (Y-A)
Filter Timer=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:06 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 exc -> is_include report
The test checks for the following case:
Router State Report Received New Router State Actions
EXCLUDE (X,Y) IS_IN (A) EXCLUDE (X+A, Y-A) (A)=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:05 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 exc -> allow report
The test checks for the following case:
Router State Report Received New Router State Actions
EXCLUDE (X,Y) ALLOW (A) EXCLUDE (X+A,Y-A) (A)=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:04 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 inc -> to_exclude report
The test checks for the following case:
Router State Report Received New Router State Actions
INCLUDE (A) TO_EX (B) EXCLUDE (A*B,B-A) (B-A)=0
Delete (A-B)
Send Q(MA,A*B)
Filter Timer=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:03 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 inc -> is_exclude report
The test checks for the following case:
Router State Report Received New Router State Actions
INCLUDE (A) IS_EX (B) EXCLUDE (A*B, B-A) (B-A)=0
Delete (A-B)
Filter Timer=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:02 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 inc -> is_include report
The test checks for the following case:
Router State Report Received New Router State Actions
INCLUDE (A) IS_IN (B) INCLUDE (A+B) (B)=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:01 +0000 (19:24 +0200)]
selftests: net: bridge: add test for mldv2 inc -> allow report
The test checks for the following case:
Router State Report Received New Router State Actions
INCLUDE (A) ALLOW (B) INCLUDE (A+B) (B)=MALI
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:24:00 +0000 (19:24 +0200)]
selftests: net: bridge: add initial MLDv2 include test
Add the initial setup for MLDv2 tests with the first test of a simple
is_include report. For MLDv2 we need to setup the bridge properly and we
also send the full precooked packets instead of relying on mausezahn to
fill in some parts. For verification we use the generic S,G state checking
functions from lib.sh.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:23:59 +0000 (19:23 +0200)]
selftests: net: bridge: factor out and rename sg state functions
Factor out S,G entry state checking functions for existence, forwarding,
blocking and timer to lib.sh so they can be later used by MLDv2 tests.
Add brmcast_ suffix to their name to make the relation to the bridge
explicit.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:23:58 +0000 (19:23 +0200)]
selftests: net: lib: add support for IPv6 mcast packet test
In order to test an IPv6 multicast packet we need to pass different tc
and mausezahn protocols only, so add a simple check for the destination
address which decides if we should generate an IPv4 or IPv6 mcast
packet.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov [Tue, 3 Nov 2020 17:23:57 +0000 (19:23 +0200)]
selftests: net: bridge: factor out mcast_packet_test
Factor out mcast_packet_test into lib.sh so it can be later extended and
reused by MLDv2 tests.
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
DENG Qingfang [Tue, 3 Nov 2020 05:06:18 +0000 (13:06 +0800)]
net: dsa: mt7530: support setting MTU
MT7530/7531 has a global RX packet length register, which can be used
to set MTU.
Supported packet length values are 1522 (1518 if untagged), 1536,
1552, and multiple of 1024 (from 2048 to 15360).
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Link: https://lore.kernel.org/r/20201103050618.11419-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Thu, 5 Nov 2020 00:28:07 +0000 (16:28 -0800)]
Merge branch 'net-ipa-tell-gsi-the-ipa-version'
Alex Elder says:
====================
net: ipa: tell GSI the IPA version
The GSI code that supports IPA avoids having knowledge about the
IPA layer it serves. One result of this is that Boolean flags are
used during GSI initialization to convey that certain hardware
version-dependent special behaviors should be used.
A given version of IPA hardware uses a fixed/well-defined version
of GSI, so the IPA version really implies the GSI version.
If given only the IPA version, the GSI code supporting IPA can
use it to implement certain special behaviors required for IPA
*or* GSI. This avoids the need to pass and maintain numerous
Boolean flags.
====================
Link: https://lore.kernel.org/r/20201102175400.6282-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:54:00 +0000 (11:54 -0600)]
net: ipa: eliminate legacy arguments
We enable a channel doorbell engine only for IPA v3.5.1, and that is
now handled directly by gsi_channel_program().
When initially setting up a channel, we want that doorbell engine
enabled, and we can request that independent of the IPA version.
Doing that makes the "legacy" argument to gsi_channel_setup_one()
unnecessary. And with that gone we can get rid of the "legacy"
argument to gsi_channel_setup(), and gsi_setup() as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:53:59 +0000 (11:53 -0600)]
net: ipa: use version in gsi_channel_program()
Use the IPA version in gsi_channel_program() to determine whether
we should enable the GSI doorbell engine when requested. This way,
callers only say whether or not it should be enabled if needed,
regardless of hardware version.
Rename the "legacy" argument to gsi_channel_reset(), and have
it indicate whether the doorbell engine should be enabled when
reprogramming following the reset.
Change all callers of gsi_channel_reset() to indicate whether to
enable the doorbell engine after reset, independent of hardware
version.
Rework a little logic in ipa_endpoint_reset() to get rid of the
"legacy" variable previously passed to gsi_channel_reset().
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:53:58 +0000 (11:53 -0600)]
net: ipa: use version in gsi_channel_reset()
A quirk of IPA v3.5.1 requires a channel reset on an RX channel to
be performed twice. Use the IPA version in gsi_channel_reset()
rather than the passed-in legacy flag to determine that.
This is actually a bug fix, because this double reset is supposed
to occur independent of whether we're enabling the doorbell engine.
Now they will be independent.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:53:57 +0000 (11:53 -0600)]
net: ipa: use version in gsi_channel_init()
A quirk of IPA v4.2 requires the AP to allocate the GSI channels
that are owned by the modem.
Rather than pass a flag argument to gsi_channel_init(), use the
IPA version directly in that function to determine whether modem
channels need to be allocated.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:53:56 +0000 (11:53 -0600)]
net: ipa: record IPA version in GSI structure
Record the IPA version passed to gsi_init() in the GSI structure.
This allows that value to be used directly where needed, rather than
passing and storing certain flag arguments through the code.
In particular, for all but one supported version of IPA, the command
channel is programmed to only use an "escape buffer". By storing
the IPA version, we can do a simple version check in one location,
and avoid storing a flag field in every channel (and passing a flag
along while initializing channels to set that field properly).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:53:55 +0000 (11:53 -0600)]
net: ipa: expose IPA version to the GSI layer
Although GSI is integral to IPA, it is a separate hardware component
and the IPA code supporting it has been structured to avoid explicit
dependence on IPA details. An example of this is that gsi_init() is
passed a number of Boolean flags to indicate special behaviors,
whose values are dependent on the IPA hardware version. Looking
ahead, newer hardware versions would require even more such special
behaviors.
For any given version of IPA hardware (like 3.5.1 or 4.2), the GSI
hardware version is fixed (in this case, 1.3 and 2.2, respectively).
So the IPA version *implies* the GSI version, and the IPA version
can be used as effectively the equivalent of the GSI hardware version.
Rather than proliferating new special behavior flags, just provide
the IPA version to the GSI layer when it is initialized. The GSI
code can then use that directly to determine whether special
behaviors are required. The IPA version enumerated type is already
isolated to its own header file, so the exposure of this IPA detail
is very limited.
For now, just change gsi_init() to pass the version rather than the
Boolean flags, and set the flag values internal to that function.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alex Elder [Mon, 2 Nov 2020 17:34:35 +0000 (11:34 -0600)]
net: ipa: restrict special reset to IPA v3.5.1
With IPA v3.5.1, if IPA aggregation is active at the time an
underlying GSI channel reset is performed, some special handling
is required.
There is logic in ipa_endpoint_reset() that arranges for that
special handling, but it's done for all hardware versions, not
just IPA v3.5.1.
Fix the logic to properly restrict the special behavior.
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201102173435.5987-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Vinay Kumar Yadav [Mon, 2 Nov 2020 16:28:33 +0000 (21:58 +0530)]
chelsio/chtls: Utilizing multiple rxq/txq to process requests
patch adds a logic to utilize multiple queues to process requests.
The queue selection logic uses a round-robin distribution technique
using a counter.
Signed-off-by: Ayush Sawal <ayush.sawal@chelsio.com>
Signed-off-by: Vinay Kumar Yadav <vinay.yadav@chelsio.com>
Link: https://lore.kernel.org/r/20201102162832.22344-1-vinay.yadav@chelsio.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Mon, 2 Nov 2020 13:46:01 +0000 (13:46 +0000)]
octeontx2-pf: Fix sizeof() mismatch
An incorrect sizeof() is being used, sizeof(u64 *) is not correct,
it should be sizeof(*sq->sqb_ptrs).
Addresses-Coverity: ("Sizeof not portable (SIZEOF_MISMATCH)")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201102134601.698436-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Colin Ian King [Mon, 2 Nov 2020 12:16:15 +0000 (12:16 +0000)]
net: dev_ioctl: remove redundant initialization of variable err
The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201102121615.695196-1-colin.king@canonical.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
kernel test robot [Mon, 2 Nov 2020 08:38:30 +0000 (09:38 +0100)]
forcedeth: fix excluded_middle.cocci warnings
Condition !A || A && B is equivalent to !A || B.
Generated by: scripts/coccinelle/misc/excluded_middle.cocci
Fixes:
b76f0ea01312 ("coccinelle: misc: add excluded_middle.cocci script")
CC: Denis Efremov <efremov@linux.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Link: https://lore.kernel.org/r/alpine.DEB.2.22.394.2011020936100.3077@hadrien
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Willy Liu [Mon, 2 Nov 2020 01:52:07 +0000 (09:52 +0800)]
net: phy: realtek: Add support for RTL8221B-CG series
Realtek single-port 2.5Gbps Ethernet PHYs are list as below:
RTL8226-CG: the 1st generation 2.5Gbps single port PHY
RTL8226B-CG/RTL8221B-CG: the 2nd generation 2.5Gbps single port PHY
RTL8221B-VB-CG: the 3rd generation 2.5Gbps single port PHY
RTL8221B-VM-CG: the 2.5Gbps single port PHY with MACsec feature
This patch adds the minimal drivers to manage these transceivers.
Signed-off-by: Willy Liu <willy.liu@realtek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1604281927-9874-1-git-send-email-willy.liu@realtek.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 4 Nov 2020 01:41:46 +0000 (17:41 -0800)]
Merge branch 'fsl-qbman-in_interrupt-cleanup'
Sebastian Andrzej Siewior says:
====================
fsl/qbman: in_interrupt() cleanup.
This is the in_interrupt() clean for FSL DPAA framework and the two
users.
The `napi' parameter has been renamed to `sched_napi', the other parts
are same as in the previous post [0].
[0] https://lkml.kernel.org/r/
20201027225454.3492351-1-bigeasy@linutronix.de
====================
Link: https://lore.kernel.org/r/20201101232257.3028508-1-bigeasy@linutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sebastian Andrzej Siewior [Sun, 1 Nov 2020 23:22:57 +0000 (00:22 +0100)]
crypto: caam: Replace in_irq() usage.
The driver uses in_irq() + in_serving_softirq() magic to decide if NAPI
scheduling is required or packet processing.
The usage of in_*() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context.
Use the `sched_napi' argument passed by the callback. It is set true if
called from the interrupt handler and NAPI should be scheduled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Sebastian Andrzej Siewior [Sun, 1 Nov 2020 23:22:56 +0000 (00:22 +0100)]
net: dpaa: Replace in_irq() usage.
The driver uses in_irq() + in_serving_softirq() magic to decide if NAPI
scheduling is required or packet processing.
The usage of in_*() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context.
Use the `sched_napi' argument passed by the callback. It is set true if
called from the interrupt handler and NAPI should be scheduled.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Sebastian Andrzej Siewior [Sun, 1 Nov 2020 23:22:55 +0000 (00:22 +0100)]
soc/fsl/qbman: Add an argument to signal if NAPI processing is required.
dpaa_eth_napi_schedule() and caam_qi_napi_schedule() schedule NAPI if
invoked from:
- Hard interrupt context
- Any context which is not serving soft interrupts
Any context which is not serving soft interrupts includes hard interrupts
so the in_irq() check is redundant. caam_qi_napi_schedule() has a comment
about this:
/*
* In case of threaded ISR, for RT kernels in_irq() does not return
* appropriate value, so use in_serving_softirq to distinguish between
* softirq and irq contexts.
*/
if (in_irq() || !in_serving_softirq())
This has nothing to do with RT. Even on a non RT kernel force threaded
interrupts run obviously in thread context and therefore in_irq() returns
false when invoked from the handler.
The extension of the in_irq() check with !in_serving_softirq() was there
when the drivers were added, but in the out of tree FSL BSP the original
condition was in_irq() which got extended due to failures on RT.
The usage of in_xxx() in drivers is phased out and Linus clearly requested
that code which changes behaviour depending on context should either be
separated or the context be conveyed in an argument passed by the caller,
which usually knows the context. Right he is, the above construct is
clearly showing why.
The following callchains have been analyzed to end up in
dpaa_eth_napi_schedule():
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
portal_isr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
Both need to schedule NAPI.
The crypto part has another code path leading up to this:
kill_fq()
empty_retired_fq()
qman_p_poll_dqrr()
__poll_portal_fast()
fq->cb.dqrr()
dpaa_eth_napi_schedule()
kill_fq() is called from task context and ends up scheduling NAPI, but
that's pointless and an unintended side effect of the !in_serving_softirq()
check.
The code path:
caam_qi_poll() -> qman_p_poll_dqrr()
is invoked from NAPI and I *assume* from crypto's NAPI device and not
from qbman's NAPI device. I *guess* it is okay to skip scheduling NAPI
(because this is what happens now) but could be changed if it is wrong
due to `budget' handling.
Add an argument to __poll_portal_fast() which is true if NAPI needs to be
scheduled. This requires propagating the value to the caller including
`qman_cb_dqrr' typedef which is used by the dpaa and the crypto driver.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Aymen Sghaier <aymen.sghaier@nxp.com>
Cc: Herbert XS <herbert@gondor.apana.org.au>
Cc: Li Yang <leoyang.li@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Tested-by: Camelia Groza <camelia.groza@nxp.com>
Sergej Bauer [Sun, 1 Nov 2020 22:35:55 +0000 (01:35 +0300)]
lan743x: fix for potential NULL pointer dereference with bare card
This is the 3rd revision of the patch fix for potential null pointer dereference
with lan743x card.
The simpliest way to reproduce: boot with bare lan743x and issue "ethtool ethN"
commant where ethN is the interface with lan743x card. Example:
$ sudo ethtool eth7
dmesg:
[ 103.510336] BUG: kernel NULL pointer dereference, address:
0000000000000340
...
[ 103.510836] RIP: 0010:phy_ethtool_get_wol+0x5/0x30 [libphy]
...
[ 103.511629] Call Trace:
[ 103.511666] lan743x_ethtool_get_wol+0x21/0x40 [lan743x]
[ 103.511724] dev_ethtool+0x1507/0x29d0
[ 103.511769] ? avc_has_extended_perms+0x17f/0x440
[ 103.511820] ? tomoyo_init_request_info+0x84/0x90
[ 103.511870] ? tomoyo_path_number_perm+0x68/0x1e0
[ 103.511919] ? tty_insert_flip_string_fixed_flag+0x82/0xe0
[ 103.511973] ? inet_ioctl+0x187/0x1d0
[ 103.512016] dev_ioctl+0xb5/0x560
[ 103.512055] sock_do_ioctl+0xa0/0x140
[ 103.512098] sock_ioctl+0x2cb/0x3c0
[ 103.512139] __x64_sys_ioctl+0x84/0xc0
[ 103.512183] do_syscall_64+0x33/0x80
[ 103.512224] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 103.512274] RIP: 0033:0x7f54a9cba427
...
Previous versions can be found at:
v1:
initial version
https://lkml.org/lkml/2020/10/28/921
v2:
do not return from lan743x_ethtool_set_wol if netdev->phydev == NULL, just skip
the call of phy_ethtool_set_wol() instead.
https://lkml.org/lkml/2020/10/31/380
v3:
in function lan743x_ethtool_set_wol:
use ternary operator instead of if-else sentence (review by Markus Elfring)
return -ENETDOWN insted of -EIO (review by Andrew Lunn)
Signed-off-by: Sergej Bauer <sbauer@blackbox.su>
Link: https://lore.kernel.org/r/20201101223556.16116-1-sbauer@blackbox.su
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Sun, 1 Nov 2020 22:30:44 +0000 (23:30 +0100)]
r8169: set IRQF_NO_THREAD if MSI(X) is enabled
We had to remove flag IRQF_NO_THREAD because it conflicts with shared
interrupts in case legacy interrupts are used. Following up on the
linked discussion set IRQF_NO_THREAD if MSI or MSI-X is used, because
both guarantee that interrupt won't be shared.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://www.spinics.net/lists/netdev/msg695341.html
Link: https://lore.kernel.org/r/446cf5b8-dddd-197f-cb96-66783141ade4@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Heiner Kallweit [Sun, 1 Nov 2020 22:23:52 +0000 (23:23 +0100)]
r8169: align number of tx descriptors with vendor driver
Lowest number of tx descriptors used in the vendor drivers is 256 in
r8169. r8101/r8168/r8125 use 1024 what seems to be the hw limit. Stay
on the safe side and go with 256, same as number of rx descriptors.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/a52a6de4-f792-5038-ae2f-240d3b7860eb@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 4 Nov 2020 01:27:17 +0000 (17:27 -0800)]
Merge branch 'mlxsw-spectrum-prepare-for-xm-implementation-lpm-trees'
Ido Schimmel says:
====================
mlxsw: spectrum: Prepare for XM implementation - LPM trees
Jiri says:
This is a preparation patchset for follow-up support of boards with
extended mezzanine (XM), which are going to allow extended (scale-wise)
router offload.
XM requires a separate set of PRM registers to be used to configure LPM
trees. Therefore, this patchset introduces operations that allow
different implementations of tree configuration for legacy router
offload and the XM router offload.
====================
Link: https://lore.kernel.org/r/20201101134215.713708-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko [Sun, 1 Nov 2020 13:42:15 +0000 (15:42 +0200)]
mlxsw: spectrum_router: Introduce low-level ops and implement them for RALXX regs
In preparation for support of XM router implementation which uses
different registers to work with trees and FIB entries, introduce
a structure to hold low-level ops and implement tree manipulation
register ops.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jiri Pirko [Sun, 1 Nov 2020 13:42:14 +0000 (15:42 +0200)]
mlxsw: reg: Add XRALXX Registers
Add a couple of registers used to manipulate LPM trees on XM:
The XRALTA is used to allocate the XLT LPM trees.
The XRALST is used to set and query the structure of an XLT LPM tree.
The XRALTB register is used to bind virtual router and protocol to
an allocated LPM tree.
Since the XM registers are identical to the legacy router registers
with a fixed offset, re-use their pack functions.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Jakub Kicinski [Wed, 4 Nov 2020 00:54:00 +0000 (16:54 -0800)]
Merge branch 'net-allow-virtual-netdevs-to-forward-udp-l4-and-fraglist-gso-skbs'
Alexander Lobakin says:
====================
net: allow virtual netdevs to forward UDP L4 and fraglist GSO skbs
NETIF_F_GSO_UDP_L4 and NETIF_F_GSO_FRAGLIST allow drivers to offload
GSO UDP L4. This works well on simple setups, but when any logical
netdev (e.g. VLAN) is present, kernel stack always performs software
resegmentation which actually kills the performance.
The full path in such cases is like:
1. Our NIC driver advertises a support for fraglists, GSO UDP L4, GSO
fraglists.
2. User enables fraglisted GRO via Ethtool.
3. GRO subsystem receives UDP frames from driver and merges the packets
into fraglisted GSO skb(s).
4. Networking stack queues it up for xmitting.
5. Virtual device like VLAN doesn't advertise a support for GSO UDP L4
and GSO fraglists, so skb_gso_check() doesn't allow to pass this skb
as is to the real driver.
6. Kernel then has to form a bunch of regular UDP skbs from that one and
pass it to the driver instead. This fallback is *extremely* slow for
any GSO types, but especially for GSO fraglists.
7. All further processing performs with a series of plain UDP skbs, and
the driver gets it one-by-one, despite that it supports UDP L4 and
fraglisted GSO.
That's not OK because:
a) logical/virtual netdevs like VLANs, bridges etc. should pass GSO skbs
as is;
b) even if the final driver doesn't support such type of GSO, this
software resegmenting should be performed right before it, not in the
middle of processing -- I think I even saw that note somewhere in
kernel documentation, and it's totally reasonable in terms of
performance.
Despite the fact that no mainline drivers currently supports fraglist
GSO, this should and can be easily fixed by adding UDP L4 and fraglist
GSO to the list of GSO types that can be passed-through the logical
interfaces (NETIF_F_GSO_SOFTWARE). After this change, no resegmentation
occurs (if a particular driver supports and advertises this), and the
performance goes on par with e.g. 1:1 forwarding.
The only logical netdevs that seem to be unaffected to this are bridge
interfaces, as their code uses full NETIF_F_GSO_MASK.
Tested on MIPS32 R2 router board with a WIP NIC driver in VLAN NAT:
20 Mbps baseline, 1 Gbps / link speed with this patch.
Since v1 [1]:
- handle bonding and team drivers as suggested by Willem de Bruijn;
- reword and expand the introduction with the particular example.
[1] https://lore.kernel.org/netdev/Mx3BWGop6fGORN6Cpo4mHIHz2b1bb0eLxeMG8vsijnk@cp3-web-020.plabs.ch
====================
Link: https://lore.kernel.org/r/NysZRGMkuWq0KPTCJ1Dz2FTjRkeJXDH3edVrsEeJkQI@cp4-web-036.plabs.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Sun, 1 Nov 2020 13:17:17 +0000 (13:17 +0000)]
net: bonding, dummy, ifb, team: advertise NETIF_F_GSO_SOFTWARE
Virtual netdevs should use NETIF_F_GSO_SOFTWARE to forward GSO skbs
as-is and let the final drivers deal with them when supported.
Also remove NETIF_F_GSO_UDP_L4 from bonding and team drivers as it's
now included in the "software" list.
Suggested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Alexander Lobakin [Sun, 1 Nov 2020 13:17:07 +0000 (13:17 +0000)]
net: add GSO UDP L4 and GSO fraglists to the list of software-backed types
Commit
e20cf8d3f1f7 ("udp: implement GRO for plain UDP sockets.") and
commit
9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.") made UDP L4
and fraglisted GRO/GSO fully supported by the software fallback mode.
We can safely add them to NETIF_F_GSO_SOFTWARE to allow logical/virtual
netdevs to forward these types of skbs up to the real drivers.
Signed-off-by: Alexander Lobakin <alobakin@pm.me>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:11 +0000 (11:45 +0000)]
net: net_failover: Correct parameter name 'standby_dev'
Fixes the following W=1 kernel build warning(s):
drivers/net/net_failover.c:711: warning: Function parameter or member 'standby_dev' not described in 'net_failover_create'
drivers/net/net_failover.c:711: warning: Excess function parameter 'dev' description in 'net_failover_create'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-30-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:10 +0000 (11:45 +0000)]
net: netconsole: Add description for 'netconsole_target's extended attribute
Fixes the following W=1 kernel build warning(s):
drivers/net/netconsole.c:104: warning: Function parameter or member 'extended' not described in 'netconsole_target'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-29-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:09 +0000 (11:45 +0000)]
net: usb: r8152: Fix a couple of spelling errors in fw_phy_nc's docs
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:992: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-28-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:08 +0000 (11:45 +0000)]
net: macvlan: Demote nonconformant function header
Fixes the following W=1 kernel build warning(s):
drivers/net/macvlan.c:1350: warning: Function parameter or member 'vlan' not described in 'macvlan_changelink_sources'
drivers/net/macvlan.c:1350: warning: Function parameter or member 'mode' not described in 'macvlan_changelink_sources'
drivers/net/macvlan.c:1350: warning: Function parameter or member 'data' not described in 'macvlan_changelink_sources'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-27-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:07 +0000 (11:45 +0000)]
net: macsec: Add missing documentation for 'gro_cells'
Fixes the following W=1 kernel build warning(s):
drivers/net/macsec.c:113: warning: Function parameter or member 'gro_cells' not described in 'macsec_dev'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-26-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:06 +0000 (11:45 +0000)]
net: usb: lan78xx: Remove lots of set but unused 'ret' variables
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/lan78xx.c: In function ‘lan78xx_read_raw_otp’:
drivers/net/usb/lan78xx.c:825:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_write_raw_otp’:
drivers/net/usb/lan78xx.c:879:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_deferred_multicast_write’:
drivers/net/usb/lan78xx.c:1041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_update_flowcontrol’:
drivers/net/usb/lan78xx.c:1127:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_init_mac_address’:
drivers/net/usb/lan78xx.c:1666:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_link_status_change’:
drivers/net/usb/lan78xx.c:1841:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_irq_bus_sync_unlock’:
drivers/net/usb/lan78xx.c:1920:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan8835_fixup’:
drivers/net/usb/lan78xx.c:1994:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_rx_max_frame_length’:
drivers/net/usb/lan78xx.c:2192:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_change_mtu’:
drivers/net/usb/lan78xx.c:2270:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_mac_addr’:
drivers/net/usb/lan78xx.c:2299:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_features’:
drivers/net/usb/lan78xx.c:2333:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_suspend’:
drivers/net/usb/lan78xx.c:3807:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-25-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:05 +0000 (11:45 +0000)]
net: ieee802154: ca8210: Fix incorrectly named function param doc
Fixes the following W=1 kernel build warning(s):
drivers/net/ieee802154/ca8210.c:724: warning: Function parameter or member 'cas_ctl' not described in 'ca8210_rx_done'
drivers/net/ieee802154/ca8210.c:724: warning: Excess function parameter 'cas_ctrl' description in 'ca8210_rx_done'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-24-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:04 +0000 (11:45 +0000)]
net: usb: r8152: Provide missing documentation for some struct members
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'blk_hdr' not described in 'fw_mac'
drivers/net/usb/r8152.c:934: warning: Function parameter or member 'reserved' not described in 'fw_mac'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:947: warning: Function parameter or member 'reserved' not described in 'fw_phy_patch_key'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'blk_hdr' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_pre' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'mode_post' not described in 'fw_phy_nc'
drivers/net/usb/r8152.c:986: warning: Function parameter or member 'reserved' not described in 'fw_phy_nc'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20201102114512.1062724-23-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:02 +0000 (11:45 +0000)]
net: ieee802154: ca8210: Fix a bunch of kernel-doc issues
Fixes the following W=1 kernel build warning(s):
drivers/net/ieee802154/ca8210.c:326: warning: Function parameter or member 'readq' not described in 'ca8210_test'
drivers/net/ieee802154/ca8210.c:375: warning: Function parameter or member 'spi_transfer_complete' not described in 'ca8210_priv'
drivers/net/ieee802154/ca8210.c:375: warning: Function parameter or member 'sync_exchange_complete' not described in 'ca8210_priv'
drivers/net/ieee802154/ca8210.c:375: warning: Function parameter or member 'promiscuous' not described in 'ca8210_priv'
drivers/net/ieee802154/ca8210.c:430: warning: Function parameter or member 'short_address' not described in 'macaddr'
drivers/net/ieee802154/ca8210.c:723: warning: Function parameter or member 'cas_ctl' not described in 'ca8210_rx_done'
drivers/net/ieee802154/ca8210.c:723: warning: Excess function parameter 'arg' description in 'ca8210_rx_done'
drivers/net/ieee802154/ca8210.c:1289: warning: Excess function parameter 'device_ref' description in 'tdme_checkpibattribute'
drivers/net/ieee802154/ca8210.c:3054: warning: Function parameter or member 'spi_device' not described in 'ca8210_remove'
drivers/net/ieee802154/ca8210.c:3054: warning: Excess function parameter 'priv' description in 'ca8210_remove'
drivers/net/ieee802154/ca8210.c:3104: warning: Function parameter or member 'spi_device' not described in 'ca8210_probe'
drivers/net/ieee802154/ca8210.c:3104: warning: Excess function parameter 'priv' description in 'ca8210_probe'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-21-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:01 +0000 (11:45 +0000)]
net: fddi: skfp: ess: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/ess.c:43:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-20-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:45:00 +0000 (11:45 +0000)]
net: fddi: skfp: drvfbi: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/drvfbi.c:26:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-19-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:58 +0000 (11:44 +0000)]
net: fddi: skfp: srf: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/srf.c:30:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-17-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:57 +0000 (11:44 +0000)]
net: fddi: skfp: hwt: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/hwt.c:31:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-16-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:56 +0000 (11:44 +0000)]
net: fddi: skfp: smttimer: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/smttimer.c:22:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-15-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:53 +0000 (11:44 +0000)]
net: fddi: skfp: smtinit: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/smtinit.c:23:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-12-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:52 +0000 (11:44 +0000)]
net: fddi: skfp: smtdef: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/smtdef.c:26:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-11-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:51 +0000 (11:44 +0000)]
net: fddi: skfp: rmt: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/rmt.c:49:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-10-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:50 +0000 (11:44 +0000)]
net: fddi: skfp: queue: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/queue.c:22:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-9-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:49 +0000 (11:44 +0000)]
net: fddi: skfp: pmf: Remove defined but unused variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/pmf.c:28:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-8-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:45 +0000 (11:44 +0000)]
net: fddi: skfp: pcmplc: Remove defined but not used variable 'ID_sccs'
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/pcmplc.c:49:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-4-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:44 +0000 (11:44 +0000)]
net: fddi: skfp: ecm: Remove seemingly unused variable 'ID_sccs'
This variable is present in many source files and has not been used
anywhere (at least internally) since it was introduced.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/ecm.c: In function ‘ecm_fsm’:
drivers/net/fddi/skfp/ecm.c:44:19: warning: ‘ID_sccs’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-3-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Lee Jones [Mon, 2 Nov 2020 11:44:43 +0000 (11:44 +0000)]
net: fddi: skfp: ecm: Protect 'if' when AIX_EVENT is not defined
When AIX_EVENT is not defined, the 'if' body will be empty, which
makes GCC complain. Place bracketing around the invocation to protect
it.
Fixes the following W=1 kernel build warning(s):
drivers/net/fddi/skfp/ecm.c: In function ‘ecm_fsm’:
drivers/net/fddi/skfp/ecm.c:153:29: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-2-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ido Schimmel [Sun, 1 Nov 2020 11:39:26 +0000 (13:39 +0200)]
vxlan: Use a per-namespace nexthop listener instead of a global one
The nexthop notification chain is a per-namespace chain and not a global
one like the netdev notification chain.
Therefore, a single (global) listener cannot be registered to all these
chains simultaneously as it will result in list corruptions whenever
listeners are registered / unregistered.
Instead, register a different listener in each namespace.
Currently this is not an issue because only the VXLAN driver registers a
listener to this chain, but this is going to change with netdevsim and
mlxsw also registering their own listeners.
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20201101113926.705630-1-idosch@idosch.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
projects / platform / kernel / linux-starfive.git / log