vti4: Don't count header length twice on tunnel setup

[ Upstream commit dd1df24737727e119c263acf1be2a92763938297 ]

This re-introduces the effect of commit a32452366b72 ("vti4:
Don't count header length twice.") which was accidentally
reverted by merge commit f895f0cfbb77 ("Merge branch 'master' of
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec").

The commit message from Steffen Klassert said:

    We currently count the size of LL_MAX_HEADER and struct iphdr
    twice for vti4 devices, this leads to a wrong device mtu.
    The size of LL_MAX_HEADER and struct iphdr is already counted in
    ip_tunnel_bind_dev(), so don't do it again in vti_tunnel_init().

And this is still the case now: ip_tunnel_bind_dev() already
accounts for the header length of the link layer (not
necessarily LL_MAX_HEADER, if the output device is found), plus
one IP header.

For example, with a vti device on top of veth, with MTU of 1500,
the existing implementation would set the initial vti MTU to
1332, accounting once for LL_MAX_HEADER (128, included in
hard_header_len by vti) and twice for the same IP header (once
from hard_header_len, once from ip_tunnel_bind_dev()).

It should instead be 1480, because ip_tunnel_bind_dev() is able
to figure out that the output device is veth, so no additional
link layer header is attached, and will properly count one
single IP header.

The existing issue had the side effect of avoiding PMTUD for
most xfrm policies, by arbitrarily lowering the initial MTU.
However, the only way to get a consistent PMTU value is to let
the xfrm PMTU discovery do its course, and commit d6af1a31cc72
("vti: Add pmtu handling to vti_xmit.") now takes care of local
delivery cases where the application ignores local socket
notifications.

Fixes: b9959fd3b0fa ("vti: switch to new ip tunnel code")
Fixes: f895f0cfbb77 ("Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Acked-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix skbuff rcsum on packet reroute

[ Upstream commit fc04fdb2c8a894283259f5621d31d75610701091 ]

batadv_check_unicast_ttvn may redirect a packet to itself or another
originator. This involves rewriting the ttvn and the destination address in
the batadv unicast header. These field were not yet pulled (with skb rcsum
update) and thus any change to them also requires a change in the receive
checksum.

Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Fixes: a73105b8d4c7 ("batman-adv: improved client announcement mechanism")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix header size check in batadv_dbg_arp()

[ Upstream commit 6f27d2c2a8c236d296201c19abb8533ec20d212b ]

Checking for 0 is insufficient: when an SKB without a batadv header, but
with a VLAN header is received, hdr_size will be 4, making the following
code interpret the Ethernet header as a batadv header.

Fixes: be1db4f6615b ("batman-adv: make the Distributed ARP Table vlan aware")
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: Fix vlan untag for bridge and vlan_dev with reorder_hdr off

[ Upstream commit 4bbb3e0e8239f9079bf1fe20b3c0cb598714ae61 ]

When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().

The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.

The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.

In rx path single tag case, it works as follows:

- Before skb_reorder_vlan_header()

 mac_header                                data
   v                                        v
   +-------------------+-------------+------+----
   |        ETH        |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TYPE |
   +-------------------+-------------+------+----
   <-------- mac_len --------->
                       <------------->
                        to be removed

- After skb_reorder_vlan_header()

            mac_header                     data
                 v                          v
                 +-------------------+------+----
                 |        ETH        | ETH  |
                 |       ADDRS       | TYPE |
                 +-------------------+------+----
                 <-------- mac_len --------->

This is ok, but in rx double tag case, it corrupts packets:

- Before skb_reorder_vlan_header()

 mac_header                                              data
   v                                                      v
   +-------------------+-------------+-------------+------+----
   |        ETH        |    VLAN     |    VLAN     | ETH  |
   |       ADDRS       | TPID | TCI  | TPID | TCI  | TYPE |
   +-------------------+-------------+-------------+------+----
   <--------------- mac_len ---------------->
                                     <------------->
                                    should be removed
                       <--------------------------->
                         actually will be removed

- After skb_reorder_vlan_header()

            mac_header                                   data
                 v                                        v
                               +-------------------+------+----
                               |        ETH        | ETH  |
                               |       ADDRS       | TYPE |
                               +-------------------+------+----
                 <--------------- mac_len ---------------->

So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.

skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.

Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff11170 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/imx: move arming of the vblank event to atomic_flush

[ Upstream commit 6a055b92de15af987b4027826d43aa103c65a3c4 ]

Right now the vblank event completion is racing with the atomic update,
which is especially bad when the PRE is in use, as one of the hardware
issue workaround might extend the atomic commit for quite some time.

If the vblank IRQ happens to trigger during that time, we will prematurely
signal the atomic commit completion to userspace, which causes tearing
when userspace re-uses a framebuffer we haven't managed to flip away from
yet.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sunvnet: does not support GSO for sctp

[ Upstream commit cf55612a945039476abfd73e39064b2e721c3272 ]

The NETIF_F_GSO_SOFTWARE implies support for GSO on SCTP, but the
sunvnet driver does not support GSO for sctp.  Here we remove the
NETIF_F_GSO_SOFTWARE feature flag and only report NETIF_F_ALL_TSO
instead.

Signed-off-by: Cathy Zhou <Cathy.Zhou@Oracle.COM>
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ipv4: lock mtu in fnhe when received PMTU < net.ipv4.route.min_pmtu

[ Upstream commit d52e5a7e7ca49457dd31fc8b42fb7c0d58a31221 ]

Prior to the rework of PMTU information storage in commit
2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer."),
when a PMTU event advertising a PMTU smaller than
net.ipv4.route.min_pmtu was received, we would disable setting the DF
flag on packets by locking the MTU metric, and set the PMTU to
net.ipv4.route.min_pmtu.

Since then, we don't disable DF, and set PMTU to
net.ipv4.route.min_pmtu, so the intermediate router that has this link
with a small MTU will have to drop the packets.

This patch reestablishes pre-2.6.39 behavior by splitting
rtable->rt_pmtu into a bitfield with rt_mtu_locked and rt_pmtu.
rt_mtu_locked indicates that we shouldn't set the DF bit on that path,
and is checked in ip_dont_fragment().

One possible workaround is to set net.ipv4.route.min_pmtu to a value low
enough to accommodate the lowest MTU encountered.

Fixes: 2c8cec5c10bc ("ipv4: Cache learned PMTU information in inetpeer.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

workqueue: use put_device() instead of kfree()

[ Upstream commit 537f4146c53c95aac977852b371bafb9c6755ee1 ]

Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized in this function instead.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bnxt_en: Check valid VNIC ID in bnxt_hwrm_vnic_set_tpa().

[ Upstream commit 3c4fe80b32c685bdc02b280814d0cfe80d441c72 ]

During initialization, if we encounter errors, there is a code path that
calls bnxt_hwrm_vnic_set_tpa() with invalid VNIC ID.  This may cause a
warning in firmware logs.

Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ebtables: fix erroneous reject of last rule

[ Upstream commit 932909d9b28d27e807ff8eecb68c7748f6701628 ]

The last rule in the blob has next_entry offset that is same as total size.
This made "ebtables32 -A OUTPUT -d de:ad:be:ef:01:02" fail on 64 bit kernel.

Fixes: b71812168571fa ("netfilter: ebtables: CONFIG_COMPAT: don't trust userland offsets")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: mv_xor_v2: Fix clock resource by adding a register clock

[ Upstream commit 3cd2c313f1d618f92d1294addc6c685c17065761 ]

On the CP110 components which are present on the Armada 7K/8K SoC we need
to explicitly enable the clock for the registers. However it is not
needed for the AP8xx component, that's why this clock is optional.

With this patch both clock have now a name, but in order to be backward
compatible, the name of the first clock is not used. It allows to still
use this clock with a device tree using the old binding.

Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: Relax ARM_SMCCC_ARCH_WORKAROUND_1 discovery

[ Upstream commit e21da1c992007594d391e7b301779cf30f438691 ]

A recent update to the ARM SMCCC ARCH_WORKAROUND_1 specification
allows firmware to return a non zero, positive value to describe
that although the mitigation is implemented at the higher exception
level, the CPU on which the call is made is not affected.

Let's relax the check on the return value from ARCH_WORKAROUND_1
so that we only error out if the returned value is negative.

Fixes: b092201e0020 ("arm64: Add ARM_SMCCC_ARCH_WORKAROUND_1 BP hardening support")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen: xenbus: use put_device() instead of kfree()

[ Upstream commit 351b2bccede1cb673ec7957b35ea997ea24c8884 ]

Never directly free @dev after calling device_register(), even
if it returned an error! Always use put_device() to give up the
reference initialized.

Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/core: Fix possible crash to access NULL netdev

[ Upstream commit bb7f8f199c354c4cf155b1d6d55f86eaaed7fa5a ]

resolved_dev returned might be NULL as ifindex is transient number.
Ignoring NULL check of resolved_dev might crash the kernel.
Therefore perform NULL check before accessing resolved_dev.

Additionally rdma_resolve_ip_route() invokes addr_resolve() which
performs check and address translation for loopback ifindex.
Therefore, checking it again in rdma_resolve_ip_route() is not helpful.
Therefore, the code is simplified to avoid IFF_LOOPBACK check.

Fixes: 200298326b27 ("IB/core: Validate route when we init ah")
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: smsc911x: Fix unload crash when link is up

[ Upstream commit e06513d78d54e6c7026c9043a39e2c01ee25bdbe ]

The smsc911x driver will crash if it is rmmod'ed while the netdev
is up like:

Call trace:
  phy_detach+0x94/0x150
  phy_disconnect+0x40/0x50
  smsc911x_stop+0x104/0x128 [smsc911x]
  __dev_close_many+0xb4/0x138
  dev_close_many+0xbc/0x190
  rollback_registered_many+0x140/0x460
  rollback_registered+0x68/0xb0
  unregister_netdevice_queue+0x100/0x118
  unregister_netdev+0x28/0x38
  smsc911x_drv_remove+0x58/0x130 [smsc911x]
  platform_drv_remove+0x30/0x50
  device_release_driver_internal+0x15c/0x1f8
  driver_detach+0x54/0x98
  bus_remove_driver+0x64/0xe8
  driver_unregister+0x34/0x60
  platform_driver_unregister+0x20/0x30
  smsc911x_cleanup_module+0x14/0xbca8 [smsc911x]
  SyS_delete_module+0x1e8/0x238
  __sys_trace_return+0x0/0x4

This is caused by the mdiobus being unregistered/free'd
and the code in phy_detach() attempting to manipulate mdio
related structures from unregister_netdev() calling close()

To fix this, we delay the mdiobus teardown until after
the netdev is deregistered.

Reported-by: Matt Sealey <matt.sealey@arm.com>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net: qcom/emac: Use proper free methods during TX

[ Upstream commit cc5db3150e87fe7f7e947bf333b6c1c97f848ecb ]

This patch fixes the warning messages/call traces seen if DMA debug is
enabled, In case of fragmented skb's memory was allocated using
dma_map_page but freed using dma_unmap_single. This patch modifies buffer
allocations in TX path to use dma_map_page in all the places and
dma_unmap_page while freeing the buffers.

Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fsl/fman: avoid sleeping in atomic context while adding an address

[ Upstream commit 803fafbe0cd522fa6b9e41ca3b96cfb2e2a2222d ]

__dev_mc_add grabs an adress spinlock so use
atomic context in kmalloc.

/ # ifconfig eth0 inet 192.168.0.111
[   89.331622] BUG: sleeping function called from invalid context at mm/slab.h:420
[   89.339002] in_atomic(): 1, irqs_disabled(): 0, pid: 1035, name: ifconfig
[   89.345799] 2 locks held by ifconfig/1035:
[   89.349908]  #0:  (rtnl_mutex){+.+.}, at: [<(ptrval)>] devinet_ioctl+0xc0/0x8a0
[   89.357258]  #1:  (_xmit_ETHER){+...}, at: [<(ptrval)>] __dev_mc_add+0x28/0x80
[   89.364520] CPU: 1 PID: 1035 Comm: ifconfig Not tainted 4.16.0-rc3-dirty #8
[   89.371464] Call Trace:
[   89.373908] [e959db60] [c066f948] dump_stack+0xa4/0xfc (unreliable)
[   89.380177] [e959db80] [c00671d8] ___might_sleep+0x248/0x280
[   89.385833] [e959dba0] [c01aec34] kmem_cache_alloc_trace+0x174/0x320
[   89.392179] [e959dbd0] [c04ab920] dtsec_add_hash_mac_address+0x130/0x240
[   89.398874] [e959dc00] [c04a9d74] set_multi+0x174/0x1b0
[   89.404093] [e959dc30] [c04afb68] dpaa_set_rx_mode+0x68/0xe0
[   89.409745] [e959dc40] [c057baf8] __dev_mc_add+0x58/0x80
[   89.415052] [e959dc60] [c060fd64] igmp_group_added+0x164/0x190
[   89.420878] [e959dca0] [c060ffa8] ip_mc_inc_group+0x218/0x460
[   89.426617] [e959dce0] [c06120fc] ip_mc_up+0x3c/0x190
[   89.431662] [e959dd10] [c0607270] inetdev_event+0x250/0x620
[   89.437227] [e959dd50] [c005f190] notifier_call_chain+0x80/0xf0
[   89.443138] [e959dd80] [c0573a74] __dev_notify_flags+0x54/0xf0
[   89.448964] [e959dda0] [c05743f8] dev_change_flags+0x48/0x60
[   89.454615] [e959ddc0] [c0606744] devinet_ioctl+0x544/0x8a0
[   89.460180] [e959de10] [c060987c] inet_ioctl+0x9c/0x1f0
[   89.465400] [e959de80] [c05479a8] sock_ioctl+0x168/0x460
[   89.470708] [e959ded0] [c01cf3ec] do_vfs_ioctl+0xac/0x8c0
[   89.476099] [e959df20] [c01cfc40] SyS_ioctl+0x40/0xc0
[   89.481147] [e959df40] [c0011318] ret_from_syscall+0x0/0x3c
[   89.486715] --- interrupt: c01 at 0x1006943c
[   89.486715]     LR = 0x100c45ec

Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fbdev: Fixing arbitrary kernel leak in case FBIOGETCMAP_SPARC in sbusfb_ioctl_helper().

[ Upstream commit 250c6c49e3b68756b14983c076183568636e2bde ]

Fixing arbitrary kernel leak in case FBIOGETCMAP_SPARC in
sbusfb_ioctl_helper().

'index' is defined as an int in sbusfb_ioctl_helper().
We retrieve this from the user:
if (get_user(index, &c->index) ||
    __get_user(count, &c->count) ||
    __get_user(ured, &c->red) ||
    __get_user(ugreen, &c->green) ||
    __get_user(ublue, &c->blue))
       return -EFAULT;

and then we use 'index' in the following way:
red = cmap->red[index + i] >> 8;
green = cmap->green[index + i] >> 8;
blue = cmap->blue[index + i] >> 8;

This is a classic information leak vulnerability. 'index' should be
an unsigned int, given its usage above.

This patch is straight-forward; it changes 'index' to unsigned int
in two switch-cases: FBIOGETCMAP_SPARC && FBIOPUTCMAP_SPARC.

This patch fixes CVE-2018-6412.

Signed-off-by: Peter Malone <peter.malone@gmail.com>
Acked-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx5: Fix an error code in __mlx5_ib_modify_qp()

[ Upstream commit 5d414b178e950ce9685c253994cc730893d5d887 ]

"err" is either zero or possibly uninitialized here.  It should be
-EINVAL.

Fixes: 427c1e7bcd7e ("{IB, net}/mlx5: Move the modify QP operation table to mlx5_ib")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Include GID type when deleting GIDs from HW table under RoCE

[ Upstream commit a18177925c252da7801149abe217c05b80884798 ]

The commit cited below added a gid_type field (RoCEv1 or RoCEv2)
to GID properties.

When adding GIDs, this gid_type field was copied over to the
hardware gid table. However, when deleting GIDs, the gid_type field
was not copied over to the hardware gid table.

As a result, when running RoCEv2, all RoCEv2 gids in the
hardware gid table were set to type RoCEv1 when any gid was deleted.

This problem would persist until the next gid was added (which would again
restore the gid_type field for all the gids in the hardware gid table).

Fix this by copying over the gid_type field to the hardware gid table
when deleting gids, so that the gid_type of all remaining gids is
preserved when a gid is deleted.

Fixes: b699a859d17b ("IB/mlx4: Add gid_type to GID properties")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

IB/mlx4: Fix corruption of RoCEv2 IPv4 GIDs

[ Upstream commit 0077416a3d529baccbe07ab3242e8db541cfadf6 ]

When using IPv4 addresses in RoCEv2, the GID format for the mapped
IPv4 address should be: ::ffff:<4-byte IPv4 address>.

In the cited commit, IPv4 mapped IPV6 addresses had the 3 upper dwords
zeroed out by memset, which resulted in deleting the ffff field.

However, since procedure ipv6_addr_v4mapped() already verifies that the
gid has format ::ffff:<ipv4 address>, no change is needed for the gid,
and the memset can simply be removed.

Fixes: 7e57b85c444c ("IB/mlx4: Add support for setting RoCEv2 gids in hardware")
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix iWARP write and send with immediate

[ Upstream commit 551e1c67b4207455375a2e7a285dea1c7e8fc361 ]

iWARP does not support RDMA WRITE or SEND with immediate data.
Driver should check this before submitting to FW and return an
immediate error

Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

RDMA/qedr: Fix kernel panic when running fio over NFSoRDMA

[ Upstream commit e3fd112cbf21d049faf64ba1471d72b93c22109a ]

Race in qedr_poll_cq, lastest_cqe wasn't protected by lock,
leading to a case where two context's accessing poll_cq at
the same time lead to one of them having a pointer to an old
latest_cqe and reading an invalid cqe element

Signed-off-by: Amit Radzi <Amit.Radzi@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ia64/err-inject: Use get_user_pages_fast()

[ Upstream commit 69c907022a7d9325cdc5c9dd064571e445df9a47 ]

At the point of sysfs callback, the call to gup is
done without mmap_sem (or any lock for that matter).
This is racy. As such, use the get_user_pages_fast()
alternative and safely avoid taking the lock, if possible.

Signed-off-by: Davidlohr Bueso <dbueso@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: allocate ring descriptors with dma_zalloc_coherent

[ Upstream commit aea3fca005fb45f80869f2e8d56fd4e64c1d1fdb ]

Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)

This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.

Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack:      00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0:     00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0:   ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!

Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

e1000e: Fix check_for_link return value with autoneg off

[ Upstream commit 4e7dc08e57c95673d2edaba8983c3de4dd1f65f5 ]

When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.

Fixes: 19110cfbb34d ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix multicast packet loss with a single WANT_ALL_IPV4/6 flag

[ Upstream commit 74c12c630fe310eb7fcae1b292257d47781fff0a ]

As the kernel doc describes too the code is supposed to skip adding
multicast TT entries if both the WANT_ALL_IPV4 and WANT_ALL_IPV6 flags
are present.

Unfortunately, the current code even skips adding multicast TT entries
if only either the WANT_ALL_IPV4 or WANT_ALL_IPV6 is present.

This could lead to IPv6 multicast packet loss if only an IGMP but not an
MLD querier is present for instance or vice versa.

Fixes: 687937ab3489 ("batman-adv: Add multicast optimization support for bridged setups")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: sbsa: use 32-bit read for WCV

[ Upstream commit 93ac3deb7c220cbcec032a967220a1f109d58431 ]

According to SBSA spec v3.1 section 5.3:
  All registers are 32 bits in size and should be accessed using
  32-bit reads and writes. If an access size other than 32 bits
  is used then the results are IMPLEMENTATION DEFINED.
  [...]
  The Generic Watchdog is little-endian

The current code uses readq to read the watchdog compare register
which does a 64-bit access. This fails on ThunderX2 which does not
implement 64-bit access to this register.

Fix this by using lo_hi_readq() that does two 32-bit reads.

Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

watchdog: f71808e_wdt: Fix magic close handling

[ Upstream commit 7bd3e7b743956afbec30fb525bc3c5e22e3d475c ]

Watchdog close is "expected" when any byte is 'V' not just the last one.
Writing "V" to the device fails because the last byte is the end of string.

$ echo V > /dev/watchdog
f71808e_wdt: Unexpected close, not stopping watchdog!

Signed-off-by: Igor Pylypiv <igor.pylypiv@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix TX of CCMP 256

[ Upstream commit de04d4fbf87b769ab18c480e4f020c53e74bbdd2 ]

We don't have enough room in the TX command for a CCMP 256
key, and need to use key from table.

Fixes: 3264bf032bd9 ("[BUGFIX] iwlwifi: mvm: Fix CCMP IV setting")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

KVM: PPC: Book3S HV: Fix VRMA initialization with 2MB or 1GB memory backing

[ Upstream commit debd574f4195e205ba505b25e19b2b797f4bcd94 ]

The current code for initializing the VRMA (virtual real memory area)
for HPT guests requires the page size of the backing memory to be one
of 4kB, 64kB or 16MB.  With a radix host we have the possibility that
the backing memory page size can be 2MB or 1GB.  In these cases, if the
guest switches to HPT mode, KVM will not initialize the VRMA and the
guest will fail to run.

In fact it is not necessary that the VRMA page size is the same as the
backing memory page size; any VRMA page size less than or equal to the
backing memory page size is acceptable.  Therefore we now choose the
largest page size out of the set {4k, 64k, 16M} which is not larger
than the backing memory page size.

Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests/powerpc: Skip the subpage_prot tests if the syscall is unavailable

[ Upstream commit cd4a6f3ab4d80cb919d15897eb3cbc85c2009d4b ]

The subpage_prot syscall is only functional when the system is using
the Hash MMU. Since commit 5b2b80714796 ("powerpc/mm: Invalidate
subpage_prot() system call on radix platforms") it returns ENOENT when
the Radix MMU is active. Currently this just makes the test fail.

Additionally the syscall is not available if the kernel is built with
4K pages, or if CONFIG_PPC_SUBPAGE_PROT=n, in which case it returns
ENOSYS because the syscall is missing entirely.

So check explicitly for ENOENT and ENOSYS and skip if we see either of
those.

Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Btrfs: send, fix issuing write op when processing hole in no data mode

[ Upstream commit d4dfc0f4d39475ccbbac947880b5464a74c30b99 ]

When doing an incremental send of a filesystem with the no-holes feature
enabled, we end up issuing a write operation when using the no data mode
send flag, instead of issuing an update extent operation. Fix this by
issuing the update extent operation instead.

Trivial reproducer:

  $ mkfs.btrfs -f -O no-holes /dev/sdc
  $ mkfs.btrfs -f /dev/sdd
  $ mount /dev/sdc /mnt/sdc
  $ mount /dev/sdd /mnt/sdd

  $ xfs_io -f -c "pwrite -S 0xab 0 32K" /mnt/sdc/foobar
  $ btrfs subvolume snapshot -r /mnt/sdc /mnt/sdc/snap1

  $ xfs_io -c "fpunch 8K 8K" /mnt/sdc/foobar
  $ btrfs subvolume snapshot -r /mnt/sdc /mnt/sdc/snap2

  $ btrfs send /mnt/sdc/snap1 | btrfs receive /mnt/sdd
  $ btrfs send --no-data -p /mnt/sdc/snap1 /mnt/sdc/snap2 \
       | btrfs receive -vv /mnt/sdd

Before this change the output of the second receive command is:

  receiving snapshot snap2 uuid=f6922049-8c22-e544-9ff9-fc6755918447...
  utimes
  write foobar, offset 8192, len 8192
  utimes foobar
  BTRFS_IOC_SET_RECEIVED_SUBVOL uuid=f6922049-8c22-e544-9ff9-...

After this change it is:

  receiving snapshot snap2 uuid=564d36a3-ebc8-7343-aec9-bf6fda278e64...
  utimes
  update_extent foobar: offset=8192, len=8192
  utimes foobar
  BTRFS_IOC_SET_RECEIVED_SUBVOL uuid=564d36a3-ebc8-7343-aec9-bf6fda278e64...

Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/sun4i: Fix dclk_set_phase

[ Upstream commit e64b6afa98f3629d0c0c46233bbdbe8acdb56f06 ]

Phase value is not shifted before writing.

Shift left of 28 bits to fit right bits

Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1519836413-35023-1-git-send-email-giulio.benetti@micronovasrl.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

xen/pirq: fix error path cleanup when binding MSIs

[ Upstream commit 910f8befdf5bccf25287d9f1743e3e546bcb7ce0 ]

Current cleanup in the error path of xen_bind_pirq_msi_to_irq is
wrong. First of all there's an off-by-one in the cleanup loop, which
can lead to unbinding wrong IRQs.

Secondly IRQs not bound won't be freed, thus leaking IRQ numbers.

Note that there's no need to differentiate between bound and unbound
IRQs when freeing them, __unbind_from_irq will deal with both of them
correctly.

Fixes: 4892c9b4ada9f9 ("xen: add support for MSI message groups")
Reported-by: Hooman Mirhadi <mirhadih@amazon.com>
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Amit Shah <aams@amazon.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvmet: fix PSDT field check in command format

[ Upstream commit bffd2b61670feef18d2535e9b53364d270a1c991 ]

PSDT field section according to NVM_Express-1.3:
"This field specifies whether PRPs or SGLs are used for any data
transfer associated with the command. PRPs shall be used for all
Admin commands for NVMe over PCIe. SGLs shall be used for all Admin
and I/O commands for NVMe over Fabrics. This field shall be set to
01b for NVMe over Fabrics 1.0 implementations.

Suggested-by: Idan Burstein <idanb@mellanox.com>
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

net/tcp/illinois: replace broken algorithm reference link

[ Upstream commit ecc832758a654e375924ebf06a4ac971acb5ce60 ]

The link to the pdf containing the algorithm description is now a
dead link; it seems http://www.ifp.illinois.edu/~srikant/ has been
moved to https://sites.google.com/a/illinois.edu/srikant/ and none of
the original papers can be found there...

I have replaced it with the only working copy I was able to find.

n.b. there is also a copy available at:

http://citeseerx.ist.psu.edu/viewdoc/download?doi=10.1.1.296.6350&rep=rep1&type=pdf

However, this seems to only be a *cached* version, so I am unsure
exactly how reliable that link can be expected to remain over time
and have decided against using that one.

Signed-off-by: Joey Pabalinas <joeypabalinas@gmail.com>
 net/ipv4/tcp_illinois.c |    2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

gianfar: Fix Rx byte accounting for ndev stats

[ Upstream commit 590399ddf9561f2ed0839311c8ae1be21597ba68 ]

Don't include in the Rx bytecount of the packet sent up the stack:
the FCB (frame control block), and the padding bytes inserted by
the controller into the frame payload, nor the FCS. All these are
being pulled out of the skb by gfar_process_frame().
This issue is old, likely from the driver's beginnings, however
it was amplified by recent:
commit d903ec77118c ("gianfar: simplify FCS handling and fix memory leak")
which basically added the FCS to the Rx bytecount, and so brought
this to my attention.

Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/boot: Fix random libfdt related build errors

[ Upstream commit 64c3f648c25d108f346fdc96c15180c6b7d250e9 ]

Once in a while I see build errors similar to the following
when building images from a clean tree.

  Building powerpc:virtex-ml507:44x/virtex5_defconfig ... failed
  ------------
  Error log:
  arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
   libfdt.h: No such file or directory

  Building powerpc:bamboo:smpdev:44x/bamboo_defconfig ... failed
  ------------
  Error log:
  arch/powerpc/boot/treeboot-akebono.c:37:20: fatal error:
   libfdt.h: No such file or directory

  arch/powerpc/boot/treeboot-currituck.c:35:20: fatal error:
       libfdt.h: No such file or directory

Rebuilds will succeed.

Turns out that several source files in arch/powerpc/boot/ include
libfdt.h, but Makefile dependencies are incomplete. Let's fix that.

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: dts: NSP: Fix amount of RAM on BCM958625HR

[ Upstream commit 0a5aff64f20d92c5a6e9aeed7b5950b0b817bcd9 ]

Jon attempted to fix the amount of RAM on the BCM958625HR in commit
c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
but it seems like we tripped over some poorly documented schematics.

The top-level page of the schematics says the board has 2GB, but when
you end-up scrolling to page 6, you see two chips of 4GBit (512MB) but
what the bootloader really initializes only 512MB, any attempt to use
more than that results in data aborts. Fix this again back to 512MB.

Fixes: c53beb47f621 ("ARM: dts: NSP: Correct RAM amount for BCM958625HR board")
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sit: fix IFLA_MTU ignored on NEWLINK

[ Upstream commit 2b3957c34b6d7f03544b12ebbf875eee430745db ]

Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for sit.

Note that dev->hard_header_len setting for sit works fine, no need to
fix it. sit is actually ipv4 tunnel, it can't call ip6_tnl_change_mtu
to set mtu.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ip6_tunnel: fix IFLA_MTU ignored on NEWLINK

[ Upstream commit a6aa80446234ec0ad38eecdb8efc59e91daae565 ]

Commit 128bb975dc3c ("ip6_gre: init dev->mtu and dev->hard_header_len
correctly") fixed IFLA_MTU ignored on NEWLINK for ip6_gre. The same
mtu fix is also needed for ip6_tunnel.

Note that dev->hard_header_len setting for ip6_tunnel works fine,
no need to fix it.

Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

bcache: fix kcrashes with fio in RAID5 backend dev

[ Upstream commit 60eb34ec5526e264c2bbaea4f7512d714d791caf ]

Kernel crashed when run fio in a RAID5 backend bcache device, the call
trace is bellow:
[  440.012034] kernel BUG at block/blk-ioc.c:146!
[  440.012696] invalid opcode: 0000 [#1] SMP NOPTI
[  440.026537] CPU: 2 PID: 2205 Comm: md127_raid5 Not tainted 4.15.0 #8
[  440.027441] Hardware name: HP ProLiant MicroServer Gen8, BIOS J06 07/16
/2015
[  440.028615] RIP: 0010:put_io_context+0x8b/0x90
[  440.029246] RSP: 0018:ffffa8c882b43af8 EFLAGS: 00010246
[  440.029990] RAX: 0000000000000000 RBX: ffffa8c88294fca0 RCX: 0000000000
0f4240
[  440.031006] RDX: 0000000000000004 RSI: 0000000000000286 RDI: ffffa8c882
94fca0
[  440.032030] RBP: ffffa8c882b43b10 R08: 0000000000000003 R09: ffff949cb8
0c1700
[  440.033206] R10: 0000000000000104 R11: 000000000000b71c R12: 00000000000
01000
[  440.034222] R13: 0000000000000000 R14: ffff949cad84db70 R15: ffff949cb11
bd1e0
[  440.035239] FS:  0000000000000000(0000) GS:ffff949cba280000(0000) knlGS:
0000000000000000
[  440.060190] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  440.084967] CR2: 00007ff0493ef000 CR3: 00000002f1e0a002 CR4: 00000000001
606e0
[  440.110498] Call Trace:
[  440.135443]  bio_disassociate_task+0x1b/0x60
[  440.160355]  bio_free+0x1b/0x60
[  440.184666]  bio_put+0x23/0x30
[  440.208272]  search_free+0x23/0x40 [bcache]
[  440.231448]  cached_dev_write_complete+0x31/0x70 [bcache]
[  440.254468]  closure_put+0xb6/0xd0 [bcache]
[  440.277087]  request_endio+0x30/0x40 [bcache]
[  440.298703]  bio_endio+0xa1/0x120
[  440.319644]  handle_stripe+0x418/0x2270 [raid456]
[  440.340614]  ? load_balance+0x17b/0x9c0
[  440.360506]  handle_active_stripes.isra.58+0x387/0x5a0 [raid456]
[  440.380675]  ? __release_stripe+0x15/0x20 [raid456]
[  440.400132]  raid5d+0x3ed/0x5d0 [raid456]
[  440.419193]  ? schedule+0x36/0x80
[  440.437932]  ? schedule_timeout+0x1d2/0x2f0
[  440.456136]  md_thread+0x122/0x150
[  440.473687]  ? wait_woken+0x80/0x80
[  440.491411]  kthread+0x102/0x140
[  440.508636]  ? find_pers+0x70/0x70
[  440.524927]  ? kthread_associate_blkcg+0xa0/0xa0
[  440.541791]  ret_from_fork+0x35/0x40
[  440.558020] Code: c2 48 00 5b 41 5c 41 5d 5d c3 48 89 c6 4c 89 e7 e8 bb c2
48 00 48 8b 3d bc 36 4b 01 48 89 de e8 7c f7 e0 ff 5b 41 5c 41 5d 5d c3 <0f> 0b
0f 1f 00 0f 1f 44 00 00 55 48 8d 47 b8 48 89 e5 41 57 41
[  440.610020] RIP: put_io_context+0x8b/0x90 RSP: ffffa8c882b43af8
[  440.628575] ---[ end trace a1fd79d85643a73e ]--

All the crash issue happened when a bypass IO coming, in such scenario
s->iop.bio is pointed to the s->orig_bio. In search_free(), it finishes the
s->orig_bio by calling bio_complete(), and after that, s->iop.bio became
invalid, then kernel would crash when calling bio_put(). Maybe its upper
layer's faulty, since bio should not be freed before we calling bio_put(),
but we'd better calling bio_put() first before calling bio_complete() to
notify upper layer ending this bio.

This patch moves bio_complete() under bio_put() to avoid kernel crash.

[mlyle: fixed commit subject for character limits]

Reported-by: Matthias Ferdinand <bcache@mfedv.net>
Tested-by: Matthias Ferdinand <bcache@mfedv.net>
Signed-off-by: Tang Junhui <tang.junhui@zte.com.cn>
Reviewed-by: Michael Lyle <mlyle@lyle.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dmaengine: rcar-dmac: fix max_chunk_size for R-Car Gen3

[ Upstream commit d716d9b702bb759dd6fb50804f10a174bd156d71 ]

According to R-Car Gen3 Rev.0.80 manual, the DMATCR can be set to
16,777,215 as maximum. So, this patch fixes the max_chunk_size for
safety on all of SoCs. Otherwise, a system may hang if the DMATCR
is set to 0 on R-Car Gen3.

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

virtio-gpu: fix ioctl and expose the fixed status to userspace.

[ Upstream commit 9a191b114906457c4b2494c474f58ae4142d4e67 ]

This exposes to mesa that it can use the fixed ioctl for querying
later cap sets, cap set 1 is forever frozen in time.

Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20180221015003.22884-1-airlied@gmail.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

r8152: fix tx packets accounting

[ Upstream commit 4c27bf3c5b7434ccb9ab962301da661c26b467a4 ]

r8152 driver handles TSO packets (limited to ~16KB) quite well,
but pretends each TSO logical packet is a single packet on the wire.

There is also some error since headers are accounted once, but
error rate is small enough that we do not care.

Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

qrtr: add MODULE_ALIAS macro to smd

[ Upstream commit c77f5fbbefc04612755117775e8555c2a7006cac ]

Added MODULE_ALIAS("rpmsg:IPCRTR") to ensure qrtr-smd and qrtr will load
when IPCRTR channel is detected.

Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: orion5x: Revert commit 4904dbda41c8.

[ Upstream commit 13a55372b64e00e564a08d785ca87bd9d454ba30 ]

It is not valid for orion5x to use mac_pton().

First of all, the orion5x buffer is not NULL terminated.  mac_pton()
has no business operating on non-NULL terminated buffers because
only the caller can know that this is valid and in what manner it
is ok to parse this NULL'less buffer.

Second of all, orion5x operates on an __iomem pointer, which cannot
be dereferenced using normal C pointer operations.  Accesses to
such areas much be performed with the proper iomem accessors.

Fixes: 4904dbda41c8 ("ARM: orion5x: use mac_pton() helper")
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ceph: fix dentry leak when failing to init debugfs

[ Upstream commit 18106734b512664a8541026519ce4b862498b6c3 ]

When failing from ceph_fs_debugfs_init() in ceph_real_mount(),
there is lack of dput of root_dentry and it causes slab errors,
so change the calling order of ceph_fs_debugfs_init() and
open_root_dentry() and do some cleanups to avoid this issue.

Signed-off-by: Chengguang Xu <cgxu519@icloud.com>
Reviewed-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

clocksource/drivers/fsl_ftm_timer: Fix error return checking

[ Upstream commit f287eb9013ccf199cbfa4eabd80c36fedfc15a73 ]

The error checks on freq for a negative error return always fails because
freq is unsigned and can never be negative. Fix this by making freq a
signed long.

Detected with Coccinelle:
drivers/clocksource/fsl_ftm_timer.c:287:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0
drivers/clocksource/fsl_ftm_timer.c:291:5-9: WARNING: Unsigned expression
compared with zero: freq <= 0

Fixes: 2529c3a33079 ("clocksource: Add Freescale FlexTimer Module (FTM) timer support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: kernel-janitors@vger.kernel.org
Link: https://lkml.kernel.org/r/20180226113614.3092-1-colin.king@canonical.com
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

nvme-pci: Fix nvme queue cleanup if IRQ setup fails

[ Upstream commit f25a2dfc20e3a3ed8fe6618c331799dd7bd01190 ]

This patch fixes nvme queue cleanup if requesting an IRQ handler for
the queue's vector fails. It does this by resetting the cq_vector to
the uninitialized value of -1 so it is ignored for a controller reset.

Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
[changelog updates, removed misc whitespace changes]
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix netlink dumping of BLA backbones

[ Upstream commit fce672db548ff19e76a08a32a829544617229bc2 ]

The function batadv_bla_backbone_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.

But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.

And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.

Fixes: ea4152e11716 ("batman-adv: add backbone table netlink support")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Fix netlink dumping of BLA claims

[ Upstream commit b0264ecdfeab5f889b02ec54af7ca8cc1c245e2f ]

The function batadv_bla_claim_dump_bucket must be able to handle
non-complete dumps of a single bucket. It tries to do that by saving the
latest dumped index in *idx_skip to inform the caller about the current
state.

But the caller only assumes that buckets were not completely dumped when
the return code is non-zero. This function must therefore also return a
non-zero index when the dumping of an entry failed. Otherwise the caller
will just skip all remaining buckets.

And the function must also reset *idx_skip back to zero when it finished a
bucket. Otherwise it will skip the same number of entries in the next
bucket as the previous one had.

Fixes: 04f3f5bf1883 ("batman-adv: add B.A.T.M.A.N. Dump BLA claims via netlink")
Reported-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Ignore invalid batadv_v_gw during netlink send

[ Upstream commit 011c935fceae5252619ef730baa610c655281dda ]

The function batadv_v_gw_dump stops the processing loop when
batadv_v_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.

Fixes: b71bb6f924fe ("batman-adv: add B.A.T.M.A.N. V bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: Ignore invalid batadv_iv_gw during netlink send

[ Upstream commit 10d570284258a30dc104c50787c5289ec49f3d23 ]

The function batadv_iv_gw_dump stops the processing loop when
batadv_iv_gw_dump_entry returns a non-0 return code. This should only
happen when the buffer is full. Otherwise, an empty message may be
returned by batadv_gw_dump. This empty message will then stop the netlink
dumping of gateway entries. At worst, not a single entry is returned to
userspace even when plenty of possible gateways exist.

Fixes: efb766af06e3 ("batman-adv: add B.A.T.M.A.N. IV bat_gw_dump implementations")
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

netfilter: ebtables: convert BUG_ONs to WARN_ONs

[ Upstream commit fc6a5d0601c5ac1d02f283a46f60b87b2033e5ca ]

All of these conditions are not fatal and should have
been WARN_ONs from the get-go.

Convert them to WARN_ONs and bail out.

Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: invalidate checksum on fragment reassembly

[ Upstream commit 3bf2a09da956b43ecfaa630a2ef9a477f991a46a ]

A more sophisticated implementation could try to combine fragment checksums
when all fragments have CHECKSUM_COMPLETE and are split at even offsets.
For now, we just set ip_summed to CHECKSUM_NONE to avoid "hw csum failure"
warnings in the kernel log when fragmented frames are received. In
consequence, skb_pull_rcsum() can be replaced with skb_pull().

Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.

Fixes: 610bfc6bc99b ("batman-adv: Receive fragmented packets and merge")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

batman-adv: fix packet checksum in receive path

[ Upstream commit abd6360591d3f8259f41c34e31ac4826dfe621b8 ]

eth_type_trans() internally calls skb_pull(), which does not adjust the
skb checksum; skb_postpull_rcsum() is necessary to avoid log spam of the
form "bat0: hw csum failure" when packets with CHECKSUM_COMPLETE are
received.

Note that in usual setups, packets don't reach batman-adv with
CHECKSUM_COMPLETE (I assume NICs bail out of checksumming when they see
batadv's ethtype?), which is why the log messages do not occur on every
system using batman-adv. I could reproduce this issue by stacking
batman-adv on top of a VXLAN interface.

Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Tested-by: Maximilian Wilhelm <max@sdn.clinic>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md/raid1: fix NULL pointer dereference

[ Upstream commit 3de59bb9d551428cbdc76a9ea57883f82e350b4d ]

In handle_write_finished(), if r1_bio->bios[m] != NULL, it thinks
the corresponding conf->mirrors[m].rdev is also not NULL. But, it
is not always true.

Even if some io hold replacement rdev(i.e. rdev->nr_pending.count > 0),
raid1_remove_disk() can also set the rdev as NULL. That means,
bios[m] != NULL, but mirrors[m].rdev is NULL, resulting in NULL
pointer dereference in handle_write_finished and sync_request_write.

This patch can fix BUGs as follows:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000140
 IP: [<ffffffff815bbbbd>] raid1d+0x2bd/0xfc0
 PGD 12ab52067 PUD 12f587067 PMD 0
 Oops: 0000 [#1] SMP
 CPU: 1 PID: 2008 Comm: md3_raid1 Not tainted 4.1.44+ #130
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
 Call Trace:
  ? schedule+0x37/0x90
  ? prepare_to_wait_event+0x83/0xf0
  md_thread+0x144/0x150
  ? wake_atomic_t_function+0x70/0x70
  ? md_start_sync+0xf0/0xf0
  kthread+0xd8/0xf0
  ? kthread_worker_fn+0x160/0x160
  ret_from_fork+0x42/0x70
  ? kthread_worker_fn+0x160/0x160

 BUG: unable to handle kernel NULL pointer dereference at 00000000000000b8
 IP: sync_request_write+0x9e/0x980
 PGD 800000007c518067 P4D 800000007c518067 PUD 8002b067 PMD 0
 Oops: 0000 [#1] SMP PTI
 CPU: 24 PID: 2549 Comm: md3_raid1 Not tainted 4.15.0+ #118
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014
 Call Trace:
  ? sched_clock+0x5/0x10
  ? sched_clock_cpu+0xc/0xb0
  ? flush_pending_writes+0x3a/0xd0
  ? pick_next_task_fair+0x4d5/0x5f0
  ? __switch_to+0xa2/0x430
  raid1d+0x65a/0x870
  ? find_pers+0x70/0x70
  ? find_pers+0x70/0x70
  ? md_thread+0x11c/0x160
  md_thread+0x11c/0x160
  ? finish_wait+0x80/0x80
  kthread+0x111/0x130
  ? kthread_create_worker_on_cpu+0x70/0x70
  ? do_syscall_64+0x6f/0x190
  ? SyS_exit_group+0x10/0x10
  ret_from_fork+0x35/0x40

Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md: fix a potential deadlock of raid5/raid10 reshape

[ Upstream commit 8876391e440ba615b10eef729576e111f0315f87 ]

There is a potential deadlock if mount/umount happens when
raid5_finish_reshape() tries to grow the size of emulated disk.

How the deadlock happens?
1) The raid5 resync thread finished reshape (expanding array).
2) The mount or umount thread holds VFS sb->s_umount lock and tries to
   write through critical data into raid5 emulated block device. So it
   waits for raid5 kernel thread handling stripes in order to finish it
   I/Os.
3) In the routine of raid5 kernel thread, md_check_recovery() will be
   called first in order to reap the raid5 resync thread. That is,
   raid5_finish_reshape() will be called. In this function, it will try
   to update conf and call VFS revalidate_disk() to grow the raid5
   emulated block device. It will try to acquire VFS sb->s_umount lock.
The raid5 kernel thread cannot continue, so no one can handle mount/
umount I/Os (stripes). Once the write-through I/Os cannot be finished,
mount/umount will not release sb->s_umount lock. The deadlock happens.

The raid5 kernel thread is an emulated block device. It is responible to
handle I/Os (stripes) from upper layers. The emulated block device
should not request any I/Os on itself. That is, it should not call VFS
layer functions. (If it did, it will try to acquire VFS locks to
guarantee the I/Os sequence.) So we have the resync thread to send
resync I/O requests and to wait for the results.

For solving this potential deadlock, we can put the size growth of the
emulated block device as the final step of reshape thread.

2017/12/29:
Thanks to Guoqing Jiang <gqjiang@suse.com>,
we confirmed that there is the same deadlock issue in raid10. It's
reproducible and can be fixed by this patch. For raid10.c, we can remove
the similar code to prevent deadlock as well since they has been called
before.

Reported-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Alex Wu <alexwu@synology.com>
Reviewed-by: Chung-Chiang Cheng <cccheng@synology.com>
Signed-off-by: BingJing Chang <bingjingc@synology.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: dcache: Use READ_ONCE when accessing i_dir_seq

[ Upstream commit 8cc07c808c9d595e81cbe5aad419b7769eb2e5c9 ]

i_dir_seq is subject to concurrent modification by a cmpxchg or
store-release operation, so ensure that the relaxed access in
d_alloc_parallel uses READ_ONCE.

Reported-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

fs: dcache: Avoid livelock between d_alloc_parallel and __d_add

[ Upstream commit 015555fd4d2930bc0c86952c46ad88b3392f66e4 ]

If d_alloc_parallel runs concurrently with __d_add, it is possible for
d_alloc_parallel to continuously retry whilst i_dir_seq has been
incremented to an odd value by __d_add:

CPU0:
__d_add
n = start_dir_add(dir);
cmpxchg(&dir->i_dir_seq, n, n + 1) == n

CPU1:
d_alloc_parallel
retry:
seq = smp_load_acquire(&parent->d_inode->i_dir_seq) & ~1;
hlist_bl_lock(b);
bit_spin_lock(0, (unsigned long *)b); // Always succeeds

CPU0:
__d_lookup_done(dentry)
hlist_bl_lock
bit_spin_lock(0, (unsigned long *)b); // Never succeeds

CPU1:
if (unlikely(parent->d_inode->i_dir_seq != seq)) {
hlist_bl_unlock(b);
goto retry;
}

Since the simple bit_spin_lock used to implement hlist_bl_lock does not
provide any fairness guarantees, then CPU1 can starve CPU0 of the lock
and prevent it from reaching end_dir_add(dir), therefore CPU1 cannot
exit its retry loop because the sequence number always has the bottom
bit set.

This patch resolves the livelock by not taking hlist_bl_lock in
d_alloc_parallel if the sequence counter is odd, since any subsequent
masked comparison with i_dir_seq will fail anyway.

Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reported-by: Naresh Madhusudana <naresh.madhusudana@arm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kvm: fix warning for CONFIG_HAVE_KVM_EVENTFD builds

[ Upstream commit 076467490b8176eb96eddc548a14d4135c7b5852 ]

Move the kvm_arch_irq_routing_update() prototype outside of
ifdef CONFIG_HAVE_KVM_EVENTFD guards to fix the following sparse warning:

arch/s390/kvm/../../../virt/kvm/irqchip.c:171:28: warning: symbol 'kvm_arch_irq_routing_update' was not declared. Should it be static?

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

macvlan: fix use-after-free in macvlan_common_newlink()

[ Upstream commit 4e14bf4236490306004782813b8b4494b18f5e60 ]

The following use-after-free was reported by KASan when running
LTP macvtap01 test on 4.16-rc2:

[10642.528443] BUG: KASAN: use-after-free in
               macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10642.626607] Read of size 8 at addr ffff880ba49f2100 by task ip/18450
...
[10642.963873] Call Trace:
[10642.994352]  dump_stack+0x5c/0x7c
[10643.035325]  print_address_description+0x75/0x290
[10643.092938]  kasan_report+0x28d/0x390
[10643.137971]  ? macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.207963]  macvlan_common_newlink+0x12ef/0x14a0 [macvlan]
[10643.275978]  macvtap_newlink+0x171/0x260 [macvtap]
[10643.334532]  rtnl_newlink+0xd4f/0x1300
...
[10646.256176] Allocated by task 18450:
[10646.299964]  kasan_kmalloc+0xa6/0xd0
[10646.343746]  kmem_cache_alloc_trace+0xf1/0x210
[10646.397826]  macvlan_common_newlink+0x6de/0x14a0 [macvlan]
[10646.464386]  macvtap_newlink+0x171/0x260 [macvtap]
[10646.522728]  rtnl_newlink+0xd4f/0x1300
...
[10647.022028] Freed by task 18450:
[10647.061549]  __kasan_slab_free+0x138/0x180
[10647.111468]  kfree+0x9e/0x1c0
[10647.147869]  macvlan_port_destroy+0x3db/0x650 [macvlan]
[10647.211411]  rollback_registered_many+0x5b9/0xb10
[10647.268715]  rollback_registered+0xd9/0x190
[10647.319675]  register_netdevice+0x8eb/0xc70
[10647.370635]  macvlan_common_newlink+0xe58/0x14a0 [macvlan]
[10647.437195]  macvtap_newlink+0x171/0x260 [macvtap]

Commit d02fd6e7d293 ("macvlan: Fix one possible double free") handles
the case when register_netdevice() invokes ndo_uninit() on error and
as a result free the port. But 'macvlan_port_get_rtnl(dev))' check
(returns dev->rx_handler_data), which was added by this commit in order
to prevent double free, is not quite correct:

* for macvlan it always returns NULL because 'lowerdev' is the one that
  was used to register rx handler (port) in macvlan_port_create() as
  well as to unregister it in macvlan_port_destroy().
* for macvtap it always returns a valid pointer because macvtap registers
  its own rx handler before macvlan_common_newlink().

Fixes: d02fd6e7d293 ("macvlan: Fix one possible double free")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

arm64: fix unwind_frame() for filtered out fn for function graph tracing

[ Upstream commit 9f416319f40cd857d2bb517630e5855a905ef3fb ]

do_task_stat() calls get_wchan(), which further does unwind_frame().
unwind_frame() restores frame->pc to original value in case function
graph tracer has modified a return address (LR) in a stack frame to hook
a function return. However, if function graph tracer has hit a filtered
function, then we can't unwind it as ftrace_push_return_trace() has
biased the index(frame->graph) with a 'huge negative'
offset(-FTRACE_NOTRACE_DEPTH).

Moreover, arm64 stack walker defines index(frame->graph) as unsigned
int, which can not compare a -ve number.

Similar problem we can have with calling of walk_stackframe() from
save_stack_trace_tsk() or dump_backtrace().

This patch fixes unwind_frame() to test the index for -ve value and
restore index accordingly before we can restore frame->pc.

Reproducer:

cd /sys/kernel/debug/tracing/
echo schedule > set_graph_notrace
echo 1 > options/display-graph
echo wakeup > current_tracer
ps -ef | grep -i agent

Above commands result in:
Unable to handle kernel paging request at virtual address ffff801bd3d1e000
pgd = ffff8003cbe97c00
[ffff801bd3d1e000] *pgd=0000000000000000, *pud=0000000000000000
Internal error: Oops: 96000006 [#1] SMP
[...]
CPU: 5 PID: 11696 Comm: ps Not tainted 4.11.0+ #33
[...]
task: ffff8003c21ba000 task.stack: ffff8003cc6c0000
PC is at unwind_frame+0x12c/0x180
LR is at get_wchan+0xd4/0x134
pc : [<ffff00000808892c>] lr : [<ffff0000080860b8>] pstate: 60000145
sp : ffff8003cc6c3ab0
x29: ffff8003cc6c3ab0 x28: 0000000000000001
x27: 0000000000000026 x26: 0000000000000026
x25: 00000000000012d8 x24: 0000000000000000
x23: ffff8003c1c04000 x22: ffff000008c83000
x21: ffff8003c1c00000 x20: 000000000000000f
x19: ffff8003c1bc0000 x18: 0000fffffc593690
x17: 0000000000000000 x16: 0000000000000001
x15: 0000b855670e2b60 x14: 0003e97f22cf1d0f
x13: 0000000000000001 x12: 0000000000000000
x11: 00000000e8f4883e x10: 0000000154f47ec8
x9 : 0000000070f367c0 x8 : 0000000000000000
x7 : 00008003f7290000 x6 : 0000000000000018
x5 : 0000000000000000 x4 : ffff8003c1c03cb0
x3 : ffff8003c1c03ca0 x2 : 00000017ffe80000
x1 : ffff8003cc6c3af8 x0 : ffff8003d3e9e000

Process ps (pid: 11696, stack limit = 0xffff8003cc6c0000)
Stack: (0xffff8003cc6c3ab0 to 0xffff8003cc6c4000)
[...]
[<ffff00000808892c>] unwind_frame+0x12c/0x180
[<ffff000008305008>] do_task_stat+0x864/0x870
[<ffff000008305c44>] proc_tgid_stat+0x3c/0x48
[<ffff0000082fde0c>] proc_single_show+0x5c/0xb8
[<ffff0000082b27e0>] seq_read+0x160/0x414
[<ffff000008289e6c>] __vfs_read+0x58/0x164
[<ffff00000828b164>] vfs_read+0x88/0x144
[<ffff00000828c2e8>] SyS_read+0x60/0xc0
[<ffff0000080834a0>] __sys_trace_return+0x0/0x4

Fixes: 20380bb390a4 (arm64: ftrace: fix a stack tracer's output under function graph tracer)
Signed-off-by: Pratyush Anand <panand@redhat.com>
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
[catalin.marinas@arm.com: replace WARN_ON with WARN_ON_ONCE]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: drop frames with unexpected DS bits from fast-rx to slow path

[ Upstream commit b323ac19b7734a1c464b2785a082ee50bccd3b91 ]

Fixes rx for 4-addr packets in AP mode. These may be used for setting
up a 4-addr link for stations that are allowed to do so.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

x86/topology: Update the 'cpu cores' field in /proc/cpuinfo correctly across CPU hotplug operations

[ Upstream commit 4596749339e06dc7a424fc08a15eded850ed78b7 ]

Without this fix, /proc/cpuinfo will display an incorrect amount
of CPU cores, after bringing them offline and online again, as
exemplified below:

  $ cat /proc/cpuinfo | grep cores
  cpu cores : 4
  cpu cores : 8
  cpu cores : 8
  cpu cores : 20
  cpu cores : 4
  cpu cores : 3
  cpu cores : 2
  cpu cores : 2

This patch fixes this by always zeroing the booted_cores variable
upon turning off a logical CPU.

Tested-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Signed-off-by: Samuel Neves <sneves@dei.uc.pt>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: jgross@suse.com
Cc: luto@kernel.org
Cc: prarit@redhat.com
Cc: vkuznets@redhat.com
Link: http://lkml.kernel.org/r/20180221205036.5244-1-sneves@dei.uc.pt
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking/xchg/alpha: Fix xchg() and cmpxchg() memory ordering bugs

[ Upstream commit 472e8c55cf6622d1c112dc2bc777f68bbd4189db ]

Successful RMW operations are supposed to be fully ordered, but
Alpha's xchg() and cmpxchg() do not meet this requirement.

Will Deacon noticed the bug:

  > So MP using xchg:
  >
  > WRITE_ONCE(x, 1)
  > xchg(y, 1)
  >
  > smp_load_acquire(y) == 1
  > READ_ONCE(x) == 0
  >
  > would be allowed.

... which thus violates the above requirement.

Fix it by adding a leading smp_mb() to the xchg() and cmpxchg() implementations.

Reported-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-alpha@vger.kernel.org
Link: http://lkml.kernel.org/r/1519291488-5752-1-git-send-email-parri.andrea@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

integrity/security: fix digsig.c build error with header file

[ Upstream commit 120f3b11ef88fc38ce1d0ff9c9a4b37860ad3140 ]

security/integrity/digsig.c has build errors on some $ARCH due to a
missing header file, so add it.

  security/integrity/digsig.c:146:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]

Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: linux-integrity@vger.kernel.org
Link: http://kisskb.ellerman.id.au/kisskb/head/13396/
Signed-off-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

regulatory: add NUL to request alpha2

[ Upstream commit 657308f73e674e86b60509a430a46e569bf02846 ]

Similar to the ancient commit a5fe8e7695dc ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.

Fixes: 73d54c9e74c4 ("cfg80211: add regulatory netlink multicast group")
Reported-by: Kees Cook <keescook@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

smsc75xx: fix smsc75xx_set_features()

[ Upstream commit 88e80c62671ceecdbb77c902731ec95a4bfa62f9 ]

If an attempt is made to disable RX checksums, USB adapter is changed
but netdev->features is not, because smsc75xx_set_features() returns a
non zero value.

This throws errors from netdev_rx_csum_fault() :
<devname>: hw csum failure

Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP: Fix dmtimer init for omap1

[ Upstream commit ba6887836178d43b3665b9da075c2c5dfe1d207c ]

We need to enable PM runtime on omap1 also as otherwise we
will get errors:

omap_timer omap_timer.1: omap_dm_timer_probe: pm_runtime_get_sync failed!
omap_timer: probe of omap_timer.1 failed with error -13
...

We are checking for OMAP_TIMER_NEEDS_RESET flag elsewhere so this is
safe to do.

Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

PKCS#7: fix direct verification of SignerInfo signature

[ Upstream commit 6459ae386699a5fe0dc52cf30255f75274fa43a4 ]

If none of the certificates in a SignerInfo's certificate chain match a
trusted key, nor is the last certificate signed by a trusted key, then
pkcs7_validate_trust_one() tries to check whether the SignerInfo's
signature was made directly by a trusted key.  But, it actually fails to
set the 'sig' variable correctly, so it actually verifies the last
signature seen.  That will only be the SignerInfo's signature if the
certificate chain is empty; otherwise it will actually be the last
certificate's signature.

This is not by itself a security problem, since verifying any of the
certificates in the chain should be sufficient to verify the SignerInfo.
Still, it's not working as intended so it should be fixed.

Fix it by setting 'sig' correctly for the direct verification case.

Fixes: 757932e6da6d ("PKCS#7: Handle PKCS#7 messages that contain no X.509 certs")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cio: clear timer when terminating driver I/O

[ Upstream commit 410d5e13e7638bc146321671e223d56495fbf3c7 ]

When we terminate driver I/O (because we need to stop using a certain
channel path) we also need to ensure that a timer (which may have been
set up using ccw_device_start_timeout) is cleared.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cio: fix return code after missing interrupt

[ Upstream commit 770b55c995d171f026a9efb85e71e3b1ea47b93d ]

When a timeout occurs for users of ccw_device_start_timeout
we will stop the IO and call the drivers int handler with
the irb pointer set to ERR_PTR(-ETIMEDOUT). Sometimes
however we'd set the irb pointer to ERR_PTR(-EIO) which is
not intended. Just set the correct value in all codepaths.

Reported-by: Julian Wiedmann <jwi@linux.vnet.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

s390/cio: fix ccw_device_start_timeout API

[ Upstream commit f97a6b6c47d2f329a24f92cc0ca3c6df5727ba73 ]

There are cases a device driver can't start IO because the device is
currently in use by cio. In this case the device driver is notified
when the device is usable again.

Using ccw_device_start_timeout we would set the timeout (and change
an existing timeout) before we test for internal usage. Worst case
this could lead to an unexpected timer deletion.

Fix this by setting the timeout after we test for internal usage.

Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

powerpc/bpf/jit: Fix 32-bit JIT for seccomp_data access

[ Upstream commit 083b20907185b076f21c265b30fe5b5f24c03d8c ]

I am using SECCOMP to filter syscalls on a ppc32 platform, and noticed
that the JIT compiler was failing on the BPF even though the
interpreter was working fine.

The issue was that the compiler was missing one of the instructions
used by SECCOMP, so here is a patch to enable JIT for that
instruction.

Fixes: eb84bab0fb38 ("ppc: Kconfig: Enable BPF JIT on ppc32")
Signed-off-by: Mark Lord <mlord@pobox.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

kernel/relay.c: limit kmalloc size to KMALLOC_MAX_SIZE

[ Upstream commit 88913bd8ea2a75d7e460a4bed5f75e1c32660d7e ]

chan->n_subbufs is set by the user and relay_create_buf() does a kmalloc()
of chan->n_subbufs * sizeof(size_t *).

kmalloc_slab() will generate a warning when this fails if
chan->subbufs * sizeof(size_t *) > KMALLOC_MAX_SIZE.

Limit chan->n_subbufs to the maximum allowed kmalloc() size.

Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1802061216100.122576@chino.kir.corp.google.com
Fixes: f6302f1bcd75 ("relay: prevent integer overflow in relay_open()")
Signed-off-by: David Rientjes <rientjes@google.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md: raid5: avoid string overflow warning

[ Upstream commit 53b8d89ddbdbb0e4625a46d2cdbb6f106c52f801 ]

gcc warns about a possible overflow of the kmem_cache string, when adding
four characters to a string of the same length:

drivers/md/raid5.c: In function 'setup_conf':
drivers/md/raid5.c:2207:34: error: '-alt' directive writing 4 bytes into a region of size between 1 and 32 [-Werror=format-overflow=]
  sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
                                  ^~~~
drivers/md/raid5.c:2207:2: note: 'sprintf' output between 5 and 36 bytes into a destination of size 32
  sprintf(conf->cache_name[1], "%s-alt", conf->cache_name[0]);
  ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

If I'm counting correctly, we need 11 characters for the fixed part
of the string and 18 characters for a 64-bit pointer (when no gendisk
is used), so that leaves three characters for conf->level, which should
always be sufficient.

This makes the code use snprintf() with the correct length, to
make the code more robust against changes, and to get the compiler
to shut up.

In commit f4be6b43f1ac ("md/raid5: ensure we create a unique name for
kmem_cache when mddev has no gendisk") from 2010, Neil said that
the pointer could be removed "shortly" once devices without gendisk
are disallowed. I have no idea if that happened, but if it did, that
should probably be changed as well.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

locking/xchg/alpha: Add unconditional memory barrier to cmpxchg()

[ Upstream commit cb13b424e986aed68d74cbaec3449ea23c50e167 ]

Continuing along with the fight against smp_read_barrier_depends() [1]
(or rather, against its improper use), add an unconditional barrier to
cmpxchg.  This guarantees that dependency ordering is preserved when a
dependency is headed by an unsuccessful cmpxchg.  As it turns out, the
change could enable further simplification of LKMM as proposed in [2].

[1] https://marc.info/?l=linux-kernel&m=150884953419377&w=2
    https://marc.info/?l=linux-kernel&m=150884946319353&w=2
    https://marc.info/?l=linux-kernel&m=151215810824468&w=2
    https://marc.info/?l=linux-kernel&m=151215816324484&w=2

[2] https://marc.info/?l=linux-kernel&m=151881978314872&w=2

Signed-off-by: Andrea Parri <parri.andrea@gmail.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-alpha@vger.kernel.org
Link: http://lkml.kernel.org/r/1519152356-4804-1-git-send-email-parri.andrea@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/exynos: fix comparison to bitshift when dealing with a mask

[ Upstream commit 1293b6191010672c0c9dacae8f71c6f3e4d70cbe ]

Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drm/exynos: g2d: use monotonic timestamps

[ Upstream commit a588a8bb7b25a3fb4f7fed00feb7aec541fc2632 ]

The exynos DRM driver uses real-time 'struct timeval' values
for exporting its timestamps to user space. This has multiple
problems:

1. signed seconds overflow in y2038
2. the 'struct timeval' definition is deprecated in the kernel
3. time may jump or go backwards after a 'settimeofday()' syscall
4. other DRM timestamps are in CLOCK_MONOTONIC domain, so they
   can't be compared
5. exporting microseconds requires a division by 1000, which may
   be slow on some architectures.

The code existed in two places before, but the IPP portion was
removed in 8ded59413ccc ("drm/exynos: ipp: Remove Exynos DRM
IPP subsystem"), so we no longer need to worry about it.

Ideally timestamps should just use 64-bit nanoseconds instead, but
of course we can't change that now. Instead, this tries to address
the first four points above by using monotonic 'timespec' values.

According to Tobias Jakobi, user space doesn't care about the
timestamp at the moment, so we can change the format. Even if
there is something looking at them, it will work just fine with
monotonic times as long as the application only looks at the
relative values between two events.

Link: https://patchwork.kernel.org/patch/10038593/
Cc: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

md raid10: fix NULL deference in handle_write_completed()

[ Upstream commit 01a69cab01c184d3786af09e9339311123d63d22 ]

In the case of 'recover', an r10bio with R10BIO_WriteError &
R10BIO_IsRecover will be progressed by handle_write_completed().
This function traverses all r10bio->devs[copies].
If devs[m].repl_bio != NULL, it thinks conf->mirrors[dev].replacement
is also not NULL. However, this is not always true.

When there is an rdev of raid10 has replacement, then each r10bio
->devs[m].repl_bio != NULL in conf->r10buf_pool. However, in 'recover',
even if corresponded replacement is NULL, it doesn't clear r10bio
->devs[m].repl_bio, resulting in replacement NULL deference.

This bug was introduced when replacement support for raid10 was
added in Linux 3.3.

As NeilBrown suggested:
Elsewhere the determination of "is this device part of the
resync/recovery" is made by resting bio->bi_end_io.
If this is end_sync_write, then we tried to write here.
If it is NULL, then we didn't try to write.

Fixes: 9ad1aefc8ae8 ("md/raid10:  Handle replacement devices during resync.")
Cc: stable (V3.3+)
Suggested-by: NeilBrown <neilb@suse.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Shaohua Li <sh.li@alibaba-inc.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: Do not disconnect on invalid operating class

[ Upstream commit 191da271ac260700db3e5b4bb982a17ca78769d6 ]

Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.

However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.

To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.

Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix calling sleeping function in atomic context

[ Upstream commit 95f3ce6a77893ac828ba841df44421620de4314b ]

sta_info_alloc can be called from atomic paths (such as RX path)
so we need to call pcpu_alloc with the correct gfp.

Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: fix a possible leak of station stats

[ Upstream commit d78d9ee9d40aca4781d2c5334972544601a4c3a2 ]

If sta_info_alloc fails after allocating the per CPU statistics,
they are not properly freed.

Fixes: c9c5962b56c1 ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4

[ Upstream commit 651b9920d7a694ffb1f885aef2bbb068a25d9d66 ]

This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

rxrpc: Work around usercopy check

[ Upstream commit a16b8d0cf2ec1e626d24bc2a7b9e64ace6f7501d ]

Due to a check recently added to copy_to_user(), it's now not permitted to
copy from slab-held data to userspace unless the slab is whitelisted.  This
affects rxrpc_recvmsg() when it attempts to place an RXRPC_USER_CALL_ID
control message in the userspace control message buffer.  A warning is
generated by usercopy_warn() because the source is the copy of the
user_call_ID retained in the rxrpc_call struct.

Work around the issue by copying the user_call_ID to a variable on the
stack and passing that to put_cmsg().

The warning generated looks like:

Bad or missing usercopy whitelist? Kernel memory exposure attempt detected from SLUB object 'dmaengine-unmap-128' (offset 680, size 8)!
WARNING: CPU: 0 PID: 1401 at mm/usercopy.c:81 usercopy_warn+0x7e/0xa0
...
RIP: 0010:usercopy_warn+0x7e/0xa0
...
Call Trace:
 __check_object_size+0x9c/0x1a0
 put_cmsg+0x98/0x120
 rxrpc_recvmsg+0x6fc/0x1010 [rxrpc]
 ? finish_wait+0x80/0x80
 ___sys_recvmsg+0xf8/0x240
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? __clear_rsb+0x25/0x3d
 ? __clear_rsb+0x15/0x3d
 ? finish_task_switch+0xa6/0x2b0
 ? trace_hardirqs_on_caller+0xed/0x180
 ? _raw_spin_unlock_irq+0x29/0x40
 ? __sys_recvmsg+0x4e/0x90
 __sys_recvmsg+0x4e/0x90
 do_syscall_64+0x7a/0x220
 entry_SYSCALL_64_after_hwframe+0x26/0x9b

Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Kees Cook <keescook@chromium.org>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

NFC: llcp: Limit size of SDP URI

[ Upstream commit fe9c842695e26d8116b61b80bfb905356f07834b ]

The tlv_len is u8, so we need to limit the size of the SDP URI. Enforce
this both in the NLA policy and in the code that performs the allocation
and copy, to avoid writing past the end of the allocated buffer.

Fixes: d9b8d8e19b073 ("NFC: llcp: Service Name Lookup netlink interface")
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: always init rs with 20mhz bandwidth rates

[ Upstream commit 6b7a5aea71b342ec0593d23b08383e1f33da4c9a ]

In AP mode, when a new station associates, rs is initialized immediately
upon association completion, before the phy context is updated with the
association parameters, so the sta bandwidth might be wider than the phy
context allows.
To avoid this issue, always initialize rs with 20mhz bandwidth rate, and
after authorization, when the phy context is already up-to-date, re-init
rs with the correct bw.

Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

iwlwifi: mvm: fix security bug in PN checking

[ Upstream commit 5ab2ba931255d8bf03009c06d58dce97de32797c ]

A previous patch allowed the same PN for packets originating from the
same AMSDU by copying PN only for the last packet in the series.

This however is bogus since we cannot assume the last frame will be
received on the same queue, and if it is received on a different ueue
we will end up not incrementing the PN and possibly let the next
packet to have the same PN and pass through.

Change the logic instead to driver explicitly indicate for the second
sub frame and on to be allowed to have the same PN as the first
subframe. Indicate it to mac80211 as well for the fallback queue.

Fixes: f1ae02b186d9 ("iwlwifi: mvm: allow same PN for de-aggregated AMSDU")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ibmvnic: Free RX socket buffer in case of adapter error

[ Upstream commit 4b9b0f01350500173f17e2b2e65beb4df4ef99c7 ]

If a RX buffer is returned to the client driver with an error, free the
corresponding socket buffer before continuing.

Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP1: clock: Fix debugfs_create_*() usage

[ Upstream commit 8cbbf1745dcde7ba7e423dc70619d223de90fd43 ]

When exposing data access through debugfs, the correct
debugfs_create_*() functions must be used, depending on data type.

Remove all casts from data pointers passed to debugfs_create_*()
functions, as such casts prevent the compiler from flagging bugs.

Correct all wrong usage:
  - clk.rate is unsigned long, not u32,
  - clk.flags is u8, not u32, which exposed the successive
    clk.rate_offset and clk.src_offset fields.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP3: Fix prm wake interrupt for resume

[ Upstream commit d3be6d2a08bd26580562d9714d3d97ea9ba22c73 ]

For platform_suspend_ops, the finish call is too late to re-enable wake
irqs and we need re-enable wake irqs on wake call instead.

Otherwise noirq resume for devices has already happened. And then
dev_pm_disarm_wake_irq() has already disabled the dedicated wake irqs
when the interrupt triggers and the wake irq is never handled.

For devices that are already in PM runtime suspended state when we
enter suspend this means that a possible wake irq will never trigger.

And this can lead into a situation where a device has a pending padconf
wake irq, and the device will stay unresponsive to any further wake
irqs.

This issue can be easily reproduced by setting serial console log level
to zero, letting the serial console idle, and suspend the system from
an ssh terminal. Then try to wake up the system by typing to the serial
console.

Note that this affects only omap3 PRM interrupt as that's currently
the only omap variant that does anything in omap_pm_wake().

In general, for the wake irqs to work, the interrupt must have either
IRQF_NO_SUSPEND or IRQF_EARLY_RESUME set for it to trigger before
dev_pm_disarm_wake_irq() disables the wake irqs.

Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARM: OMAP2+: timer: fix a kmemleak caused in omap_get_timer_dt

[ Upstream commit db35340c536f1af0108ec9a0b2126a05d358d14a ]

When more than one GP timers are used as kernel system timers and the
corresponding nodes in device-tree are marked with the same "disabled"
property, then the "attr" field of the property will be initialized
more than once as the property being added to sys file system via
__of_add_property_sysfs().

In __of_add_property_sysfs(), the "name" field of pp->attr.attr is set
directly to the return value of safe_name(), without taking care of
whether it's already a valid pointer to a memory block. If it is, its
old value will always be overwritten by the new one and the memory block
allocated before will a "ghost", then a kmemleak happened.

That the same "disabled" property being added to different nodes of device
tree would cause that kind of kmemleak overhead, at least once.

To fix it, allocate the property dynamically, and delete static one.

Signed-off-by: Qi Hou <qi.hou@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: memfd: add config fragment for fuse

[ Upstream commit 9a606f8d55cfc932ec02172aaed4124fdc150047 ]

The memfd test requires to insert the fuse module (CONFIG_FUSE_FS).

Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Daniel Díaz <daniel.diaz@linaro.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

selftests: pstore: Adding config fragment CONFIG_PSTORE_RAM=m

[ Upstream commit 9a379e77033f02c4a071891afdf0f0a01eff8ccb ]

pstore_tests and pstore_post_reboot_tests need CONFIG_PSTORE_RAM=m

Signed-off-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

libata: Fix compile warning with ATA_DEBUG enabled

[ Upstream commit 0d3e45bc6507bd1f8728bf586ebd16c2d9e40613 ]

This fixs the following comile warnings with ATA_DEBUG enabled,
which detected by Linaro GCC 5.2-2015.11:

  drivers/ata/libata-scsi.c: In function 'ata_scsi_dump_cdb':
  ./include/linux/kern_levels.h:5:18: warning: format '%d' expects
  argument of type 'int', but argument 6 has type 'u64 {aka long
   long unsigned int}' [-Wformat=]

tj: Patch hand-applied and description trimmed.

Signed-off-by: Dong Bo <dongbo4@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ptr_ring: prevent integer overflow when calculating size

[ Upstream commit 54e02162d4454a99227f520948bf4494c3d972d0 ]

Switch to use dividing to prevent integer overflow when size is too
big to calculate allocation size properly.

Reported-by: Eric Biggers <ebiggers3@gmail.com>
Fixes: 6e6e41c31122 ("ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

ARC: Fix malformed ARC_EMUL_UNALIGNED default

[ Upstream commit 827cc2fa024dd6517d62de7a44c7b42f32af371b ]

'default N' should be 'default n', though they happen to have the same
effect here, due to undefined symbols (N in this case) evaluating to n
in a tristate sense.

Remove the default from ARC_EMUL_UNALIGNED instead of changing it. bool
and tristate symbols implicitly default to n.

Discovered with the
https://urldefense.proofpoint.com/v2/url?u=https-3A__github.com_ulfalizer_Kconfiglib_blob_master_examples_list-5Fundefined.py&d=DwIBAg&c=DPL6_X_6JkXFx7AXWqB0tg&r=c14YS-cH-kdhTOW89KozFhBtBJgs1zXscZojEZQ0THs&m=WxxD8ozR7QQUVzNCBksiznaisBGO_crN7PBOvAoju8s&s=1LmxsNqxwT-7wcInVpZ6Z1J27duZKSoyKxHIJclXU_M&e=
script.

Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>