NET:KS8695: add API for get rx interrupt bit

1. Add API Add k8695_get_rx_enable_bit() for get Rx interrupt
enable/status bit.
2. add some comment or document about some functions and variables.
3.  update driver version to "1.02"
4. add napi_enable() and napi_disable() in open/close file method.

Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDS/IB+IW: Move recv processing to a tasklet

Move receive processing from event handler to a tasklet.
This should help prevent hangcheck timer from going off
when RDS is under heavy load.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDS: Do not send congestion updates to loopback connections

This issue was discovered by HP's Pradeep and fixed in OFED
1.3, but not fixed in later versions, since the fix's implementation
was not immediately applyable to the later code. This patch should
do the trick for 1.4+ codebases.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDS: Fix panic on unload

Remove explicit destruction of passive connection when destroying
active end of the connection. The passive end is also on the
device's connection list, and will thus be cleaned up properly.
Panic was caused by trying to clean it up twice.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDS: Fix potential race around rds_i[bw]_allocation

"At rds_ib_recv_refill_one(), it first executes atomic_read(&rds_ib_allocation)
for if-condition checking,

and then executes atomic_inc(&rds_ib_allocation) if the condition was
not satisfied.

However, if any other code which updates rds_ib_allocation executes
between these two atomic operation executions,
it seems that it may result race condition. (especially when
rds_ib_allocation + 1 == rds_ib_sysctl_max_recv_allocation)"

This patch fixes this by using atomic_inc_unless to eliminate the
possibility of allocating more than rds_ib_sysctl_max_recv_allocation
and then decrementing the count if the allocation fails. It also
makes an identical change to the iwarp transport.

Reported-by: Shin Hong <hongshin@gmail.com>
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RDS: Add GET_MR_FOR_DEST sockopt

RDS currently supports a GET_MR sockopt to establish a
memory region (MR) for a chunk of memory. However, the fastreg
method ties a MR to a particular destination. The GET_MR_FOR_DEST
sockopt allows the remote machine to be specified, and thus
support for fastreg (aka FRWRs).

Note that this patch does *not* do all of this - it simply
implements the new sockopt in terms of the old one, so applications
can begin to use the new sockopt in preparation for cutover to
FRWRs.

Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond: Get the rtnl_link_ops support correct

- Don't call rtnl_link_unregister if rtnl_link_register fails
- Set .priv_size so we aren't stomping on uninitialized memory
  when we use netdev_priv, on bond devices created with
  ip link add type bond.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond: Add support for multiple network namespaces

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond: Implement a basic set of rtnl link ops

This implements a basic set of rtnl link ops and takes advantage of
the fact that rtnl_link_unregister kills all of the surviving
devices to all us to kill bond_free_all.  A module alias
is added so ip link add can pull in the bonding module.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond: Simplify bond device destruction

Manually inline the code from bond_deinit to bond_uninit.  bond_uninit
is the only caller and it is short.

Move the call of bond_release_all from the netdev notifier into
bond_uninit.  The call site is effectively the same and performing
the call explicitly allows all the paths for destroying a
bonding device to behave the same way.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond: Simplify bond_create.

Stop calling dev_get_by_name to see if the bond device already
exists.  register_netdevice already does that.

Stop calling bond_deinit if register_netdevice fails as bond_uninit
is guaranteed to be called if bond_init succeeds.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bond: Simply bond sysfs group creation

This patch delegates the work of creating the sysfs groups
to the netdev layer and ultimately to the device layer.  This
closes races between uevents.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Allow devices to specify a device specific sysfs group.

This isn't beautifully abstracted, but it is simple,
simplifies uses and so far is only needed for the bonding driver.

Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: use hlist_for_each_entry()

Small cleanup of __dev_get_by_name() and __dev_get_by_index()
to use hlist_for_each_entry() : They'll look like their _rcu variant.

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

veth: Fix veth_dellink method

In commit 23289a37e2b127dfc4de1313fba15bb4c9f0cd5b
(net: add a list_head parameter to dellink() method),
I forgot to actually use this parameter in veth_dellink.

I remember feeling a bit uncomfortable about veth_close(),
because it does :

netif_carrier_off(dev);
netif_carrier_off(priv->peer);

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: cleanup multiple unregistrations

The temporary copy of the VLAN group is not neccessary since the lower device
is already in the process of being unregistered, if it was neccessary the
memset of the global group would introduce a race condition.

With this removed, the changes to the original code are only a few lines, so
remove the new function and move the code back into vlan_device_event().

Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

convert kaweth to use usb_reset_configuration()

For USB 3.0 it is necessary that all drivers use the standard
API to reset a configuration. This removes a home-grown
implementation.

Signed-off-by: Oliver Neukum <oliver@neukum.org>
Hi David,

please take this for the next merge window.

Regards
Oliver
Signed-off-by: David S. Miller <davem@davemloft.net>

ax25: unsigned cannot be less than 0 in ax25_ctl_ioctl()

struct ax25_ctl_struct member `arg' is unsigned and cannot be less
than 0.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: version 1.26

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: 88E8059 support

Tentative support for newer Marvell hardware including
the Yukon-2 Optima chip. Do not have hatdware to test this yet,
code is based on vendor driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: workarounds for Yukon-2 supreme

Changes related to support of Yukon supreme chip.
Don't have this chip version to test on,
these are reverse engineered from the vendor (GPL) driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: fix receive pause thresholds

Program the receive pause thresholds differently depending on
chip version. This cloned from from the vendor (GPL) driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: add register definitions for new chips

This adds infrastructure for the newer chip versions and workarounds.
Extracted from the vendor (GPL) driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sky2: add SK-9E21M device id

This is a new ID that just showed up in latest vendor driver.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Enable heuristic selection between page and skb RX buffers

Now that we can tell whether GRO is being applied, this heuristic is
effective once more.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Feed GRO result into RX allocation policy and interrupt moderation

When GRO is successfully merging received packets, we should allocate
raw page buffers rather than skbs that will be discarded by GRO.
Otherwise, we should allocate skbs.

GRO also benefits from higher interrupt moderation, so increase the
score for mergeable RX packets.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro: Change all receive functions to return GRO result codes

This will allow drivers to adjust their receive path dynamically
based on whether GRO is being applied successfully.

Currently all in-tree callers ignore the return values of these
functions and do not need to be changed.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

gro: Name the GRO result enumeration type

This clarifies which return and parameter types are GRO result codes
and not RX result codes.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of /linux/kernel/git/davem/net-2.6

net: Fix 'Re: PACKET_TX_RING: packet size is too long'

Currently PACKET_TX_RING forces certain amount of every frame to remain
unused. This probably originates from an early version of the
PACKET_TX_RING patch that in fact used the extra space when the (since
removed) CONFIG_PACKET_MMAP_ZERO_COPY option was enabled. The current
code does not make any use of this extra space.

This patch removes the extra space reservation and lets userspace make
use of the full frame size.

Signed-off-by: Gabor Gombas <gombasg@sztaki.hu>
Signed-off-by: David S. Miller <davem@davemloft.net>

net,socket: introduce DECLARE_SOCKADDR helper to catch overflow at build time

proto_ops->getname implies copying protocol specific data
into storage unit (particulary to __kernel_sockaddr_storage).
So when we implement new protocol support we should keep such
a detail in mind (which is easy to forget about).

Lets introduce DECLARE_SOCKADDR helper which check if
storage unit is not overfowed at build time.

Eventually inet_getname is switched to use DECLARE_SOCKADDR
(to show example of usage).

Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-next-2.6

net: Introduce dev_get_by_index_rcu()

Some workloads hit dev_base_lock rwlock pretty hard.
We can use RCU lookups to avoid touching this rwlock.

netdevices are already freed after a RCU grace period, so this patch
adds no penalty at device dismantle time.

dev_ifname() converted to dev_get_by_index_rcu()

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

atm: Cleanup redundant tests on unsigned

The variables are unsigned so the `< 0' test always fails, the
other part of the test catches wrapped values.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Cleanup redundant tests on unsigned

optlen is unsigned so the `< 0' test is never true.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Cleanup redundant tests on unsigned

If there is data, the unsigned skb->len is greater than 0.

rt.sigdigits is unsigned as well, so the test `>= 0' is
always true, the other part of the test catches wrapped
values.

Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gigaset: convert strcmp chain to table lookup

Replace the sequence of strcmp calls for interpreting ZSAU parameter
strings by a table of known strings and lookup loop to improve
readability.

Impact: readability improvement, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

gigaset: checkpatch cleanup of ev-layer.c

On more step towards the holy grail of checkpatch.pl silence.

Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

bas_gigaset: checkpatch cleanup

On the quest for the holy grail of checkpatch.pl silence.

Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

ser_gigaset: checkpatch cleanup

Duly uglified as demanded by checkpatch.pl.

Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

gigaset: checkpatch cleanup

Dum sanctis checkpatch.pl'ae legibus obsequimur.

Impact: cosmetic
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

usb_gigaset: code cleanup

Reorganize the code of the Gigaset M10x driver to make it more
readable, less redundant, better aligned to the style of other
parts of the driver, and cause fewer checkpatch.pl complaints.

Impact: code reorganization, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

gigaset: fix bad assumptions about CAPI skbuffs

The CAPI interface incorrectly assumed that CAPI messages would always
start at the beginning of the data buffer: fix by treating DATA_B3
messages as the link layer header to their payload data. This fix
changes the way acknowledgement information is propagated through the
hardware specific modules and thereby impacts the ISDN4Linux variant
of the driver, too.

Also some assumptions about methods not being called from interrupt
context turned out to be unwarranted; fix by using dev_kfree_skb_any()
wherever non-interrupt context isn't guaranteed.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

gigaset: fix format string typo in CAPI dial command

A missing dot lead to garbage characters being included in the
dial command generated from a CAPI CONNECT_REQ message, which
interestingly enough worked anyway, illustrating the resilience
of the device.

Impact: bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

gigaset: CAPI module readability improvements

Replace the "ignoring Additional Info" warning message by better
readable ones citing the specific subparameters being ignored.
Make parts of the code more readable by using a local cmsg
pointer variable.

Impact: readability improvement
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow disabling of DSACK TCP option per route

Add and use no DSCAK bit in the features field.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow to turn off TCP window scale opt per route

Add and use no window scale bit in the features field.

Note that this is not the same as setting a window scale of 0
as would happen with window limit on route.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow disabling TCP timestamp options per route

Implement querying and acting upon the no timestamp bit in the feature
field.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the no SACK route option feature

Implement querying and acting upon the no sack bit in the features
field.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dst_feature to query route entry features

Adding an accessor to existing  dst_entry feautres field and
refactor the only supported feature (allfrag) to use it.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Allow tcp_parse_options to consult dst entry

We need tcp_parse_options to be aware of dst_entry to
take into account per dst_entry TCP options settings

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Sigend-off-by: Ori Finkelman <ori@comsleep.com>
Sigend-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Only parse time stamp TCP option in time wait sock

Since we only use tcp_parse_options here to check for the exietence
of TCP timestamp option in the header, it is better to call with
the "established" flag on.

Signed-off-by: Gilad Ben-Yossef <gilad@codefidence.com>
Signed-off-by: Ori Finkelman <ori@comsleep.com>
Signed-off-by: Yony Amit <yony@comsleep.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev: usb: dm9601.c can drive a device not supported yet, add support for it

I found that the current version of drivers/net/usb/dm9601.c can be used to
successfully drive a low-power, low-cost network adapter with USB ID
0a46:9000, based on a DM9000E chipset. As no device with this ID is yet
present in the kernel, I have created a patch that adds support for the device
to the dm9601 driver.

Created and tested against linux-2.6.32-rc5.

Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix firmware mailbox command timeout.

The mailbox command process would only process a maximum of 5 unrelated
firmware events while waiting for it's command completion status.
It should process an unlimited number of events while waiting for a maximum of 5 seconds.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

qlge: Fix EEH handling.

Clean up driver resources without touch the hardware. Add pci
save/restore state.

Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6mr: Optimize multiple unregistration

Speedup module unloading by factorizing synchronize_rcu() calls

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipv6 sit: Optimize multiple unregistration

Speedup module unloading by factorizing synchronize_rcu() calls

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ipmr: Optimize multiple unregistration

Speedup module unloading by factorizing synchronize_rcu() calls

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ip6tnl: Optimize multiple unregistration

Speedup module unloading by factorizing synchronize_rcu() calls

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bridge: Optimize multiple unregistration

Speedup module unloading by factorizing synchronize_rcu() calls

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Add the new PCI IDs to PCI_DEVICE_TABLE.

This patch adds the PCI IDs for the next generation chip to the
PCI_DEVICE_ID table.

Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

AF_RAW: Augment raw_send_hdrinc to expand skb to fit iphdr->ihl (v2)

Augment raw_send_hdrinc to correct for incorrect ip header length values

A series of oopses was reported to me recently.  Apparently when using AF_RAW
sockets to send data to peers that were reachable via ipsec encapsulation,
people could panic or BUG halt their systems.

I've tracked the problem down to user space sending an invalid ip header over an
AF_RAW socket with IP_HDRINCL set to 1.

Basically what happens is that userspace sends down an ip frame that includes
only the header (no data), but sets the ip header ihl value to a large number,
one that is larger than the total amount of data passed to the sendmsg call.  In
raw_send_hdrincl, we allocate an skb based on the size of the data in the msghdr
that was passed in, but assume the data is all valid.  Later during ipsec
encapsulation, xfrm4_tranport_output moves the entire frame back in the skbuff
to provide headroom for the ipsec headers.  During this operation, the
skb->transport_header is repointed to a spot computed by
skb->network_header + the ip header length (ihl).  Since so little data was
passed in relative to the value of ihl provided by the raw socket, we point
transport header to an unknown location, resulting in various crashes.

This fix for this is pretty straightforward, simply validate the value of of
iph->ihl when sending over a raw socket.  If (iph->ihl*4U) > user data buffer
size, drop the frame and return -EINVAL.  I just confirmed this fixes the
reported crashes.

Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge branch 'master' of git://git./linux/kernel/git/linville/wireless-2.6

e1000e: flow control doesn't re-enable

When changing flow control (pause) parameters, the flow control thresholds
(i.e. when to send XON/XOFF frames) may not be setup correctly on parts
with copper media.  Call the existing e1000_set_fc_watermarks()
function to set these thresholds.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan: Add support to netdev_ops.ndo_fcoe_get_wwn for VLAN device

Implements the netdev_ops.ndo_fcoe_get_wwn for VLAN device.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Add support for netdev_ops.ndo_fcoe_get_wwn to 82599

Implements the netdev_ops.ndo_fcoe_get_wwn in 82599 if it finds valid
prefix for the World Wide Node Name (WWNN) or World Wide Port Name (WWPN),
as well as valid SAN MAC address.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Add ndo_fcoe_get_wwn to net_device_ops

Add ndo_fcoe_get_wwn so Fiber Channel over Ethernet (FCoE) can make use of
the provided World Wide Port Name (WWPN) and World Wide Node Name (WWNN)
from the underlying network interface driver.

Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ixgbe: Add support for 82599 alternative WWNN/WWPN prefix

The 82599 EEPROM supports alternative prefix for World Wide Node Name
(WWNN) and World Wide Port Name (WWPN). The prefixes can be used together
with the SAN MAC address to form the WWNN and WWPN, which can be used by
upper layer drivers such as Fiber Channel over Ethernet (FCoE).

Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

vmxnet3: remove duplicate #include

Remove duplicate headerfile includes from vmxnet3_int.h

Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bonding: fix a race condition in calls to slave MII ioctls

In mii monitor mode, bond_check_dev_link() calls the the ioctl
handler of slave devices. It stores the ndo_do_ioctl function
pointer to a static (!) ioctl variable and later uses it to call the
handler with the IOCTL macro.

If another thread executes bond_check_dev_link() at the same time
(even with a different bond, which none of the locks prevent), a
race condition occurs. If the two racing slaves have different
drivers, this may result in one driver's ioctl handler being
called with a pointer to a net_device controlled with a different
driver, resulting in unpredictable breakage.

Unless I am overlooking something, the "static" must be a
copy'n'paste error (?).

Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

be2net: Changes to update ethtool get_settings function to return appropriate values.

Update ethtool get_settings function to:
- get current link speed settings from controller
- get port transceiver type from controller
- fill appropriate values for supported, phy_address

Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

e100: Fix to allow systems with FW based cards to resume from STD

Devices with loadable firmware must have their firmware reloaded
after the system resumes from sleep, but the request_firmare()
API is not available at this point in the resume flow because
tasks are not yet running, and the system will hang if it is
called. Work around this issue by only calling request_firmware()
for a device's first firmware load, and cache a copy of the pointer
to the firmware blob for that device, so that we may reload firmware
images even during resume.

Signed-off-by: David Graham <david.graham@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: update version to 4.0.65

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: module firmware hints

Add MODULE_FIRMWARE hints for various firmware file types,
required by different chip revisions.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: update module info

Update module info with QLogic signature.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: add PCI IDs for new chip

Add PCI vendor and device IDs for QLE8240 and QLE8242
CNA devices.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: refactor indirect register access

Refactor code to calculate and set indirect access
window for control registers in 2MB address space
(NX3031 or newer). Use void __iomem * data type for
absolute pci addresses.

Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

netxen: support for new firmware file format

Add support for extracting firmware from a unified
file format which embeds firmware images for all chip
revisions. Fallback to orginal file formats if new
image is not found.

Signed-off-by: Amit Kumar Salecha <amit@netxen.com>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

virtio-net: fix data corruption with OOM

virtio net used to unlink skbs from send queues on error,
but ever since 48925e372f04f5e35fec6269127c62b2c71ab794
we do not do this. This causes guest data corruption and crashes
with vhost since net core can requeue the skb or free it without
it being taken off the list.

This patch fixes this by queueing the skb after successful
transmit.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

via-velocity: Remove private device list

via-velocity maintains a list of its devices in order to determine
whether a netdev notification applies to one of them.  That can be
determined simply by checking the netdev_ops pointer, so the list can
be removed.

Compile-tested only.

Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: Corrected spelling error heurestics->heuristics

Corrected a spelling error in a function name.

Signed-off-by: Andreas Petlund <apetlund@simula.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

net: sysfs: ethtool_ops can be NULL

commit d519e17e2d01a0ee9abe083019532061b4438065
(net: export device speed and duplex via sysfs)
made the wrong assumption that netdev->ethtool_ops was always set.

This makes possible to crash kernel and let rtnl in locked state.

modprobe dummy
ip link set dummy0 up
(udev runs and crash)

Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc35815: Enable NAPI

This driver has NAPI code but it has been disabled.  Enable it now.
The non-napi code will be removed lator.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

tc35815: Fix return value of tc35815_do_interrupt when NAPI enabled

Return received count correctly even if tx completed at the same time.
Currently NAPI is disabled for this driver so this patch does not fix
any real problem.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

NET/KS8695: add support NAPI for Rx

Add support NAPI Rx API for KS8695NET driver.

v2, change the Rx function to NAPI.

in <KS8695X Integrated Multi-port Gateway Solution Register Description
 v1.0>:

Interrupt Enable Register (offset 0xE204)
Bit29 : WAN MAC Receive Interrupt Enable
Bit16 : LAN MAC Receive Interrupt Enable

Interrupt Status Register (Offset 0xF208)
Bit29: WAN MAC Receive Status
Bit16: LAN MAC Receive Status

see arch/arm/mach-ks8695/devices.c:
ks8695_wan_resources[] and ks8695_lan_resources[]
have IORESOURCE_IRQ , it have define the RX irq,
for wan, irq = 29; for lan ,irq = 16.
so we can do this read the interrupt status:

unsigned long mask_bit = 1 << ksp->rx_irq;
status = readl(KS8695_IRQ_VA + KS8695_INTST);

Signed-off-by: Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sfc: Set ip_summed correctly for page buffers passed to GRO

Page buffers containing packets with an incorrect checksum or using a
protocol not handled by hardware checksum offload were previously not
passed to LRO.  The conversion to GRO changed this, but did not set
the ip_summed value accordingly.

Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

cnic: Fix L2CTX_STATUSB_NUM offset in context memory.

The BNX2_L2CTX_STATUSB_NUM definition needs to be changed to match
the recent firmware update:

commit 078b0735881c7969aaf21469f3577831cddd9f8c
bnx2: Update firmware to 5.0.0.j3.

Without the fix, bnx2 can crash intermittently in bnx2_rx_int() when
iSCSI is enabled.

Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Benjamin Li <benli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Fix warnings in igb_set_ringparam()

drivers/net/igb/igb_ethtool.c: In function ‘igb_set_ringparam’:
drivers/net/igb/igb_ethtool.c:744: warning: comparison of distinct pointer types lacks a cast
drivers/net/igb/igb_ethtool.c:748: warning: comparison of distinct pointer types lacks a cast

Casts were to u16 on the constant, but the type of new_{r,t}x_count is
u32.  Cast to u32 instead.

Signed-off-by: David S. Miller <davem@davemloft.net>

igb: cleanup whitespace issues in igb_main.c

This patch goes through and cleans up whitespace issues in igb_main.c
to help improve readability.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: open up SCTP checksum offloads to all MACs 82576 and newer

Going forward the plan is to have the MACs support SCTP checksum offloads
so change the check from == to >=.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: limit minimum mtu to 68 to keep ip bound to interface

Limit the minimum mtu to 68 in order to prevent ip from being unbound from
the interface.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: add pci_dev in few spots to clean up use of dev_err/info/warn

This patch relpaces several references to adapter->pdev->dev with just
pdev->dev.  This allows for cleanup of several multiline dev_err/info
calls.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: replace unecessary &adapter->hw with just hw where applicable

This patch just cleans up some unecessary references to the adapter->hw
member when it has already been placed in a local variable named hw.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: cleanup clean_rx_irq_adv and alloc_rx_buffers_adv

This patch cleans up some whitespace issues in clean_rx_irq_adv.  It also
adds NUMA aware page allocation and dma error handling to
alloc_rx_buffers_adv.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: cleanup igb xmit frame path

This patch cleans up the xmit frame path for igb to better handle xmit
frame errors and avoid null pointer exceptions.  It also cleans up some
whitespace issues found in the xmit frame path.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: cleanup igb.h header whitespace and some structure formatting

This patch changes the layout of the ring and adapter structs to fill a few
holes in the structure.  It also cleans up some whitespace and formatting
issues.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: Remove invalid stats counters

There are several counters being used like they are static when in fact
they are clear on read.  In order to prevent the values from being
incorrect I am removing the defunct counters.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: cleanup interrupt enablement in regards to msix_other

This patch changes a few things so that instead of firing a link status
interrupt directly the get_link_status bit is set and the watchdog is
scheduled.  In addition the mailbox bit is now only enabled if VFs are
enabled.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: change queue ordering for 82576 based adapters

This patch changes the queue ordering for 82576 adapters so that if VFs are
enabled the queues will first be allocated out of the PF pool.  Any
remaining queues will be allocated out of other VMDq pools.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

igb: cleanup code related to ring resource allocation and free

This patch cleans up some of the ring alloc and free code to better handle
exceptions such as attempting to free resources on an already freed ring.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>