Chad Dupuis [Fri, 8 Feb 2013 06:57:51 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Extra loopback error handling for ISP83xx.
Add the following error handling for loopback diagnostic mode with ISP83xx:
1. If we do not receive an MBA_DCBX_COMPLETE after our initial set port
configuration command, try to reset the port back into normal operation.
If that fails, take a FCoE dump and then reset the chip.
2. After completing the loopback diagnostic operation, if the reset of the port
back into normal operation fails then reset the port so we take a FCoE dump
and then reset the chip.
3. When we receive an IDC notification and the requested operation is loopback
extend the loop down timer so the link does not appear to down for an
extended period of time.
[jejb: fix checkpatch issue]
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Chad Dupuis [Fri, 8 Feb 2013 06:57:50 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Unload hangs after issuing BSG commands to vport.
BSG code path increments ref count in the send path, but does not
decrement in the return path leading to hang during unload of the
driver.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Fri, 8 Feb 2013 06:57:49 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Do MPI reset only for ISP81xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Joe Carnuccio [Fri, 8 Feb 2013 06:57:48 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Do link initialization on get loop id failure.
To avoid continually doing ISP resets when get loop id fails to
obtain the adapter loop id, first try to do a link initialization.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Giridhar Malavali [Fri, 8 Feb 2013 06:57:47 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Update the FTP site references in the driver sources.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Chad Dupuis [Fri, 8 Feb 2013 06:57:46 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Reject loopback request if one is already in progress.
If another function on the port has initiated a loopback operation do not
process the current request.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Joe Carnuccio [Fri, 8 Feb 2013 06:57:45 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Print thermal unsupported message.
When the Read SFP mailbox command fails on the thermal device,
print a message explaining that thermal is not supported.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Masanari Iida [Fri, 8 Feb 2013 06:57:44 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Avoid null pointer dereference in shutdown routine.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Fri, 8 Feb 2013 06:57:43 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Get VPD information from common location for CNA.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Andrew Vasquez [Fri, 8 Feb 2013 06:57:42 +0000 (01:57 -0500)]
[SCSI] qla2xxx: Correct race in loop_state assignment during reset handling.
There's a subtle race in the loop/bus-reset handling whereby a
VHA's loop-state can get incorrectly set to 'down' after the
loop-reset and firmware's completion of link re-negotiation. The
original code incorrectly assumes that firmware AENs would arrive
only after mailbox-command execution to initiate the link-flap.
Here's a good case with the old code (AENs arrive after
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:4.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:4.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=
170b8f315.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
notice how the 'Port database changed' (8014) arrived after the
bus-reset handler completed 'BUS RESET SUCCEEDED'.
Now, here's a failing case with the old code (AENs arrive before
mailbox-command completion):
qla2xxx [0000:03:00.1]-8012:91: BUS RESET ISSUED nexus=91:0:0.
qla2xxx [0000:03:00.1]-580e:91: Asynchronous P2P MODE received.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010100.
qla2xxx [0000:03:00.1]-287d:91: FCPort state transitioned from ONLINE to LOST - portid=010400.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
qla2xxx [0000:03:00.1]-5812:91: Port database changed ffff 0006 0000.
qla2xxx [0000:03:00.1]-505f:91: Link is operational (4 Gbps).
qla2xxx [0000:03:00.1]-802b:91: BUS RESET SUCCEEDED nexus=91:0:0.
qla2xxx [0000:03:00.1]-480b:91: Reset marker scheduled.
qla2xxx [0000:03:00.1]-480c:91: Reset marker end.
qla2xxx [0000:03:00.1]-480f:91: Loop resync scheduled.
qla2xxx [0000:03:00.1]-8837:91: F/W Ready - OK.
qla2xxx [0000:03:00.1]-883a:91: fw_state=3 (7, 0, 0, 0) curr time=
170be9eb2.
qla2xxx [0000:03:00.1]-280e:91: HBA in F P2P topology.
qla2xxx [0000:03:00.1]-2812:91: qla2x00_configure_hba success
qla2xxx [0000:03:00.1]-2814:91: Configure loop -- dpc flags = 0x5260.
qla2xxx [0000:03:00.1]-281e:91: Needs RSCN update and loop transition.
qla2xxx [0000:03:00.1]-286a:91: qla2x00_configure_loop *** FAILED ***.
qla2xxx [0000:03:00.1]-4810:91: Loop resync end.
qla2xxx [0000:03:00.1]-4800:91: DPC handler sleeping.
This race would ultimately lead to devices go unexpectedly
offline until another link-flap or chip-reset would cause driver
re-discovery to take place.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Saurav Kashyap [Wed, 30 Jan 2013 08:34:42 +0000 (03:34 -0500)]
[SCSI] qla2xxx: Correction to the message ids.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arun Easi [Wed, 30 Jan 2013 08:34:41 +0000 (03:34 -0500)]
[SCSI] qla2xxx: Prevent enabling target mode for unsupported HBAs.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arun Easi [Wed, 30 Jan 2013 08:34:40 +0000 (03:34 -0500)]
[SCSI] qla2xxx: Allow ISP81xx to create ATIO queues.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Arun Easi [Wed, 30 Jan 2013 08:34:39 +0000 (03:34 -0500)]
[SCSI] qla2xxx: Enable target mode support for ISP83xx.
Signed-off-by: Arun Easi <arun.easi@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Chad Dupuis [Wed, 30 Jan 2013 08:34:38 +0000 (03:34 -0500)]
[SCSI] qla2xxx: Ramp down queue depth for attached SCSI devices when driver resources are low.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Chad Dupuis [Wed, 30 Jan 2013 08:34:37 +0000 (03:34 -0500)]
[SCSI] qla2xxx: Determine the number of outstanding commands based on available resources.
Base the number of outstanding requests the driver will keep track of on the
available resources instead of being hard-coded.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Carpenter [Wed, 30 Jan 2013 07:06:02 +0000 (10:06 +0300)]
[SCSI] libosd: check for kzalloc() failure
There wasn't any error handling for this kzalloc().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Carpenter [Wed, 30 Jan 2013 07:07:31 +0000 (10:07 +0300)]
[SCSI] qla4xxx: don't free NULL dma pool
The error path calls dma_pool_free() on this path but "chap_table" is
NULL and "chap_dma" is uninitialized. It's cleaner to just return
directly.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Xiangliang Yu [Tue, 29 Jan 2013 16:25:53 +0000 (00:25 +0800)]
[SCSI] mvsas: fixed timeout issue when removing module
Root cause is libsas will clear asd_sas_port phy_mask value in sas_port_deform
after triggering destruct workqueue, but the workqueue will send sync cmd and
still need phy_mask value. Now, mvsas using asd_sas_phy setting instead of
asd_sas_port setting.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Mahesh Rajashekhara [Thu, 10 Jan 2013 12:22:51 +0000 (17:52 +0530)]
[SCSI] aacraid: 1024 max outstanding command support for Series 7 and above
Signed-off-by: Mahesh Rajashekhara <Mahesh_Rajashekhara@pmc-sierra.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Julia Lawall [Mon, 21 Jan 2013 13:02:49 +0000 (14:02 +0100)]
[SCSI] bnx2fc: adjust duplicate test
Delete successive tests to the same location. The code tested the result
of a previous allocation, that itself was already tested. It is changed to
test the result of the most recent allocation.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 21 Jan 2013 04:51:05 +0000 (23:51 -0500)]
[SCSI] qla4xxx: Update driver version to 5.03.00-k4
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Mon, 21 Jan 2013 04:51:04 +0000 (23:51 -0500)]
[SCSI] qla4xxx: Fix return code for qla4xxx_session_get_param.
While reading sysfs chap_in_idx and chap_out_idx attribute, if chap
authentication is not set we get an error as "Invalid argument".
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Mon, 21 Jan 2013 04:51:03 +0000 (23:51 -0500)]
[SCSI] qla4xxx: wait for boot target login response during probe.
Boot from SAN fails in some cases where boot target login response
is slow. In this case, probe finishes early and triggers init, which
doesn't find remote disk to mount root which leads to BFS failure.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Mon, 21 Jan 2013 04:51:02 +0000 (23:51 -0500)]
[SCSI] qla4xxx: Added support for force firmware dump
This patch force driver to collect firmware dump using following command:-
"echo 2 > /sys/class/scsi_host/hostX/device/fw_dump"
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Poornima Vonti [Mon, 21 Jan 2013 04:51:01 +0000 (23:51 -0500)]
[SCSI] qla4xxx: Re-register IRQ handler while retrying initialize of adapter
Problem:
If initialization of adapter fails for some reason, then the interrupt handlers
are released. The interrupt handlers are not registered again when initialization
of adapter is retried.
Solution:
Re-register the interrupt handler when adapter initialization is retried.
Signed-off-by: Poornima Vonti <poornima.vonti@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Karen Higgins [Mon, 21 Jan 2013 04:51:00 +0000 (23:51 -0500)]
[SCSI] qla4xxx: Throttle active IOCBs to firmware limits
Problem:
QLA4xxx firmware may assert if given more IOCBs than it can handle.
Solution:
The driver was updated to throttle the number of active IOCBs based
on the total number of IOCB buffers received from get_firmware_status
mbx_sts[2].
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Karen Higgins [Mon, 21 Jan 2013 04:50:59 +0000 (23:50 -0500)]
[SCSI] qla4xxx: Remove unnecessary code from qla4xxx_init_local_data
Removed unnecessary calls to qla4xxx_get_firmware_status from
function qla4xxx_init_local_data
Signed-off-by: Karen Higgins <karen.higgins@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nilesh Javali [Mon, 21 Jan 2013 04:50:58 +0000 (23:50 -0500)]
[SCSI] qla4xxx: Quiesce driver activities while loopback
Quiesce all different activities performed by driver upon the link events
while loopback diagnostics is in progress.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nilesh Javali [Mon, 21 Jan 2013 04:50:57 +0000 (23:50 -0500)]
[SCSI] qla4xxx: Rename MBOX_ASTS_IDC_NOTIFY to MBOX_ASTS_IDC_REQUEST_NOTIFICATION
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nilesh Javali [Mon, 21 Jan 2013 04:50:56 +0000 (23:50 -0500)]
[SCSI] qla4xxx: Add spurious interrupt messages under debug level 2
The spurious interrupt messages are seen when interrupt lines are
shared between different adapters or modules. Example, interrupt
lines are shared between qlcnic and qla4xxx and USB modules, then the
console is flooded with flurry of spurious interrupt messages
which are expected in such scenario.
Hence put these messages under debug level 2 for INTx interrupt mode.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Thadeu Lima de Souza Cascardo [Fri, 11 Jan 2013 19:12:09 +0000 (17:12 -0200)]
[SCSI] cxgb4i: Remove the scsi host device when removing device
When doing a hotplug remove of a cxgb4 device, there are still dandling
symlinks at /sys/class/scsi_host/hostX to the removed PCI device. The
upper layer device may also try to send data, which may crash the
system.
The DETACH message from the lower level driver is sent to the ULD when
the device is removed, when the scsi host should be removed from the
system, avoiding any problems.
After this patch, there are no more dangling symlinks and many attempts
to crash the system while there is SCSI activity and removing the device
have failed. Adding the device back again works as expected, with the
scsi hosts showing up again.
Based on a patch by Karen Xie.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: Karen Xie <kxie@chelsio.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Carpenter [Thu, 10 Jan 2013 09:06:20 +0000 (12:06 +0300)]
[SCSI] bfa: fix strncpy() limiter in bfad_start_ops()
The closing parenthesis is in the wrong place so it takes the sizeof a
pointer instead of the sizeof the buffer minus one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anil Gurumurthy <agurumur@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Sat, 29 Dec 2012 07:24:54 +0000 (02:24 -0500)]
[SCSI] qla4xxx: Update driver version to 5.03.00-k3
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Nilesh Javali [Sat, 29 Dec 2012 07:24:53 +0000 (02:24 -0500)]
[SCSI] qla4xxx: Correct the validation to check in get_sys_info mailbox
Check mbox_sts[3] instead of mbox_sts[4] for ISP83xx to validate size
of data returned
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Sat, 29 Dec 2012 07:24:52 +0000 (02:24 -0500)]
[SCSI] qla4xxx: Pass correct function param to qla4_8xxx_rd_direct
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:44:24 +0000 (15:44 -0500)]
[SCSI] lpfc 8.3.37: Update lpfc version for 8.3.37 driver release
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:44:16 +0000 (15:44 -0500)]
[SCSI] lpfc 8.3.37: Fixed infinite loop in lpfc_sli4_fcf_rr_next_index_get.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:44:09 +0000 (15:44 -0500)]
[SCSI] lpfc 8.3.37: Fixed crash due to SLI Port invalid resource count
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:44:00 +0000 (15:44 -0500)]
[SCSI] lpfc 8.3.37: Provide support for FCoE protocol dual-chute (ULP) operation
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:53 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Fixed stale ndlp state when the node is marked for deferred removal.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:45 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Fix potential memory corruption bug
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:37 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Fixed no-context ABTS failed with BA_RJT
Fixed no-context ABTS received on unsolicited receive queue failed with BA_RJT
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:29 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Removed use of NOP mailboxes for interrupt verification
Removed use of NOP mailboxes for interrupt verification in pci_probe_one_s4
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:19 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Fixed exhausted retry for plogi to nameserver.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:11 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Fixed ELS_REC received on the unsolicited receive queue
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart [Thu, 3 Jan 2013 20:43:03 +0000 (15:43 -0500)]
[SCSI] lpfc 8.3.37: Provide support for change_queue_type
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
wenxiong@linux.vnet.ibm.com [Fri, 11 Jan 2013 23:43:54 +0000 (17:43 -0600)]
[SCSI] ipr: Fix sparse error in ipr driver
This patch fixes the following sparse error:
CHECK drivers/scsi/ipr.c
spinlock.h:147:9: warning: context imbalance in 'ipr_reset_reload' - unexpected unlock
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
wenxiong@linux.vnet.ibm.com [Fri, 11 Jan 2013 23:43:53 +0000 (17:43 -0600)]
[SCSI] ipr: Driver version 2.6.0
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
wenxiong@linux.vnet.ibm.com [Fri, 11 Jan 2013 23:43:52 +0000 (17:43 -0600)]
[SCSI] ipr: Implement block iopoll
This patch implements blk iopoll in ipr driver for performance improvement.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
wenxiong@linux.vnet.ibm.com [Fri, 11 Jan 2013 23:43:51 +0000 (17:43 -0600)]
[SCSI] ipr: Reduce lock contention
This patch reduces lock contention while implementing distributed
completion processing.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
wenxiong@linux.vnet.ibm.com [Fri, 11 Jan 2013 23:43:50 +0000 (17:43 -0600)]
[SCSI] ipr: Add support for MSI-X and distributed completion
The new generation IBM SAS Controllers will support MSI-X interrupts and
Distributed Completion Processing features. This patch add these support
in ipr device driver.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Brian King [Fri, 11 Jan 2013 23:43:49 +0000 (17:43 -0600)]
[SCSI] ipr: Resource path error logging cleanup
The resource path as displayed by the ipr driver is the
location string identifying a location on the SAS fabric.
This patch adds the SCSI host number such that error logs
can be more easily correlated in multiple adapter configurations.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Brian King [Fri, 11 Jan 2013 23:43:48 +0000 (17:43 -0600)]
[SCSI] ipr: Handler ID memory allocation failure at module load time
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
wenxiong@linux.vnet.ibm.com [Fri, 11 Jan 2013 23:43:47 +0000 (17:43 -0600)]
[SCSI] ipr: Add sereral new CCIN definitions for new adapters support
Add the appropriate definitions and table entries for new adapter support.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Jesper Juhl [Wed, 26 Dec 2012 20:31:51 +0000 (21:31 +0100)]
[SCSI] csiostor: Don't leak mem or fail to release firmware in csio_hw_flash_config()
If kzalloc() or csio_hw_check_fwconfig() fail we may leave the
csio_hw_flash_config() function without freeing allocated memory or
firmware. This should take care of the leaks.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Sat, 22 Dec 2012 03:40:34 +0000 (19:40 -0800)]
[SCSI] bnx2fc: Bumped version to 1.0.13
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Sat, 22 Dec 2012 03:40:33 +0000 (19:40 -0800)]
[SCSI] bnx2fc: Support max IO size to 512KB
Increase max_sectors from 512 to 1024 in order to support max IO size of 512KB.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Sat, 22 Dec 2012 03:40:32 +0000 (19:40 -0800)]
[SCSI] bnx2fc: Tx/Rx byte counts reset to 0 when exceeding 32 bit values
Since the FW counters are 32-bit, accumulate the stats in the driver.
[jejb: fix checkpatch warning]
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Sat, 22 Dec 2012 03:40:31 +0000 (19:40 -0800)]
[SCSI] bnx2fc: Map the doorbell register between offload and enable requests
We used to map doorbell register after FW enable request is complete.
This causes a race condition when unsolicited event is received, and FW
sends a CQE for it. Since the doorbell is not mapped, driver does not
arm CQ, which means FW will not notify the driver for further CQ
completions. To resolve this, map the doorbell between offload and
enable, so that driver is ready to receive the unsolicited packets and
arm the CQ as soon as FW enable is performed.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Sat, 22 Dec 2012 03:40:30 +0000 (19:40 -0800)]
[SCSI] bnx2fc: Move offload/upload wait logic into a function
Moved the 'waiting for upload/offload completion' logic to respective
functions as it is called in multiple places. Also this is done in
preperation for the next patch.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bhanu Prakash Gollapudi [Fri, 11 Jan 2013 07:59:38 +0000 (23:59 -0800)]
[SCSI] bnx2fc: support software fcoe target
Software FCoE target always advertises RETRY bit even when there are no
tape LUNs behind the target. This causes the driver to enable FW support
for sequence level error recovery and perform REC/SRR. This patch
arrests the behavior by not enabling SLER feature for this target.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Julia Lawall [Sat, 22 Dec 2012 03:40:28 +0000 (19:40 -0800)]
[SCSI] bnx2fc: Remove potential NULL dereference
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Cyril Roelandt [Sat, 22 Dec 2012 03:40:27 +0000 (19:40 -0800)]
[SCSI] bnx2fc: remove useless calls to memset().
These calls are followed by calls to memcpy() on the same memory area, so they
can be safely removed.
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sreekanth Reddy [Tue, 18 Dec 2012 13:45:30 +0000 (14:45 +0100)]
[SCSI] mpt2sas: fix for driver fails EEH, recovery from injected pci bus error
This patch stops the driver to invoke kthread (which remove the dead ioc)
for some time while EEH recovery has started.
[thenzl: add a 'non_operational_loop' reset.]
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wei Yongjun [Tue, 11 Dec 2012 20:56:51 +0000 (02:26 +0530)]
[SCSI] mpt3sas: remove unused variables
The variable 'chain_flags' and 'phy_number' are initialized but never used
otherwise, So remove those unused variables.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sachin Kamat [Mon, 3 Dec 2012 10:00:17 +0000 (15:30 +0530)]
[SCSI] mpt3sas: Remove unneeded version.h header inclusion
linux/version.h is not necessary as detected by checkversion.pl script.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Tomas Henzl [Tue, 3 Jul 2012 08:08:41 +0000 (10:08 +0200)]
[SCSI] bnx2i: fix the bit manipulation when setting the error mask
The intention in bnx2i_send_fw_iscsi_init_msg was to zero out
only the lower 32bits, but instead the whole mask64 is zeroed.
This patch fixes it.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hiral Patel [Mon, 10 Dec 2012 09:21:30 +0000 (01:21 -0800)]
[SCSI] fnic: fix for trusted cos
Modified fnic driver to let hardware insert the COS value. Set bit
in descriptor to 0 telling hardware to use its lif COS configurations
to insert the COS value in the frames.
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hiral Patel [Mon, 10 Dec 2012 09:21:29 +0000 (01:21 -0800)]
[SCSI] fnic: updated MAINTAINERS list
Updated MAINTAINERS list for fnic driver with appropriate names and email ids.
Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vijaya Mohan Guvva [Mon, 10 Dec 2012 09:20:03 +0000 (01:20 -0800)]
[SCSI] bfa: Update MAINTAINERS list for BFA driver
Signed-off-by: Vijaya Mohan Guvva <vmohan@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Dan Carpenter [Fri, 7 Dec 2012 10:56:22 +0000 (13:56 +0300)]
[SCSI] mpt3sas: cut and paste bug storing trigger mpi
ioc->diag_trigger_mpi is an SL_WH_MPI_TRIGGERS_T struct.
There is a cut and paste error here and SL_WH_EVENT_TRIGGERS_T is used
instead of SL_WH_MPI_TRIGGERS_T. Since the SL_WH_EVENT_TRIGGERS_T is
smaller than SL_WH_MPI_TRIGGERS_T, it means we only clear part of the
buffer.
I've changed it to use sizeof(ioc->diag_trigger_mpi) which is a bit
simpler.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: "Sreekanth Reddy" <Sreekanth.reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Wei Yongjun [Mon, 3 Dec 2012 06:22:39 +0000 (01:22 -0500)]
[SCSI] csiostor: convert to use simple_open()
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Naresh Kumar Inna <naresh@chelsio.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Fri, 23 Nov 2012 11:58:42 +0000 (06:58 -0500)]
[SCSI] qla4xxx: Update driver version to 5.03.00-k2
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Fri, 23 Nov 2012 11:58:41 +0000 (06:58 -0500)]
[SCSI] scsi_transport_iscsi: export iscsi class session's target_id in sysfs.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Manish Rangankar [Fri, 23 Nov 2012 11:58:40 +0000 (06:58 -0500)]
[SCSI] qla4xxx: Fix memory corruption issue in qla4xxx_get_ep_fwdb.
In qla4xxx_get_ep_fwdb(), dst_addr is of type struct sockaddr.
We are copying sizeof(struct sockaddr_in6) bytes to dst_addr
which is 12 bytes larger. This will cause memory corruption.
So we change dst_addr to struct sockaddr_storage which is
of 128 byte, large enough to hold sizeof(struct sockaddr_in6).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Harish Zunjarrao [Fri, 23 Nov 2012 11:58:39 +0000 (06:58 -0500)]
[SCSI] qla4xxx: Allow reset in link down case
Issue:
Reset operation fails if port is in Link Down state
Fix:
Do not wait till HBA comes online after reset command is invoked.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Vikas Chaudhary [Fri, 23 Nov 2012 11:58:38 +0000 (06:58 -0500)]
[SCSI] qla4xxx: Fix MBOX intr switching from polling to intr mode for ISP83XX
Issue:
Mailbox command timed out after switching from polling mode to interrupt mode.
Events:-
1. Mailbox interrupts are disabled
2. FW generates AEN and at same time driver enables Mailbox Interrupt
3. Driver issues new mailbox to Firmware
In above case driver will not get AEN interrupts generated by FW in step #2 as
FW generated this AEN when interrupts are disabled. During the same time
driver enabled the mailbox interrupt, so driver will not poll for interrupt.
Driver will never process AENs generated in step #2 and issues new mailbox to
FW, but now FW is not able to post mailbox completion as AENs generated before
are not processed by driver.
Fix:
Enable Mailbox / AEN interrupts before initializing FW in case of ISP83XX.
This will make sure we process all Mailbox and AENs in interrupt mode.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Bjorn Helgaas [Tue, 6 Nov 2012 22:04:44 +0000 (15:04 -0700)]
[SCSI] gdth: Remove buggy ROM handling
The ROM address handling in gdth_init_pci() is useless and possibly
dangerous. This patch removes it.
"pci_resource_start(pdev, 8)" is not well-defined. PCI resources 0-5 are
standard PCI BARs and 6 is the expansion ROM. Resource 8 is either an
SR-IOV BAR (if CONFIG_PCI_IOV=y, resources 7-12 are SR-IOV BARs) or a
bridge window (resources 7-10).
The GDT device is neither an SR-IOV device nor a bridge, so in either case
resource 8 should be zero since struct pci_dev is allocated with kzalloc().
It is illegal for a driver to write an arbitrary address to the ROM BAR
because it has no way of knowing whether the ROM will conflict with another
device.
I think the only effect of the code being removed was to:
1) Enable the ROM at 0xFEFF0000 (possibly causing a conflict with
another device)
2) Delay one millisecond
3) Write zero to the ROM BAR, disabling it
I doubt the delay is needed, but I left it since it seems innocuous.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Linus Torvalds [Mon, 28 Jan 2013 23:15:34 +0000 (15:15 -0800)]
Merge tag 'md-3.8-fixes' of git://neil.brown.name/md
Pull dmraid fix from NeilBrown:
"Just one fix for md in 3.8
dmraid assess redundancy and replacements slightly inaccurately which
could lead to some degraded arrays failing to assemble."
* tag 'md-3.8-fixes' of git://neil.brown.name/md:
DM-RAID: Fix RAID10's check for sufficient redundancy
Linus Torvalds [Mon, 28 Jan 2013 19:53:49 +0000 (11:53 -0800)]
Merge git://git./linux/kernel/git/steve/gfs2-3.0-fixes
Pull GFS2 fix from Steven Whitehouse.
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-3.0-fixes:
GFS2: fix skip unlock condition
Linus Torvalds [Mon, 28 Jan 2013 19:52:56 +0000 (11:52 -0800)]
Merge tag 'iommu-fixes-v3.8-rc5' of git://git./linux/kernel/git/joro/iommu
Pull IOMMU fix from Joerg Roedel:
"One fix for the AMD IOMMU driver to work around broken BIOSes found in
the field. Some BIOSes forget to enable a workaround for a hardware
problem which might cause the IOMMU to stop working under high load
conditions. The fix makes sure this workaround is enabled."
* tag 'iommu-fixes-v3.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
Linus Torvalds [Mon, 28 Jan 2013 19:51:57 +0000 (11:51 -0800)]
Merge tag 'mfd-for-linus-3.8-1' of git://git./linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
Linus Torvalds [Mon, 28 Jan 2013 19:41:37 +0000 (11:41 -0800)]
Merge git://git./linux/kernel/git/davem/net
Pull networking updates from David Miller:
"Much more accumulated than I would have liked due to an unexpected
bout with a nasty flu:
1) AH and ESP input don't set ECN field correctly because the
transport head of the SKB isn't set correctly, fix from Li
RongQing.
2) If netfilter conntrack zones are disabled, we can return an
uninitialized variable instead of the proper error code. Fix from
Borislav Petkov.
3) Fix double SKB free in ath9k driver beacon handling, from Felix
Feitkau.
4) Remove bogus assumption about netns cleanup ordering in
nf_conntrack, from Pablo Neira Ayuso.
5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
Dumazet. It uses spin_is_locked() in it's test and is therefore
unsuitable for UP.
6) Fix SELINUX labelling regressions added by the tuntap multiqueue
changes, from Paul Moore.
7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
Nayak Sujir.
8) CXGB4 driver sets interrupt coalescing parameters only on first
queue, rather than all of them. Fix from Thadeu Lima de Souza
Cascardo.
9) Fix regression in the dispatch of read/write registers in dm9601
driver, from Tushar Behera.
10) ipv6_append_data miscalculates header length, from Romain KUNTZ.
11) Fix PMTU handling regressions on ipv4 routes, from Steffen
Klassert, Timo Teräs, and Julian Anastasov.
12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
expression. From Nickolai Zeldovich.
13) macvlan_get_size() causes underallocation netlink message space,
fix from Eric Dumazet.
14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
Zeldovich. Amusingly the zero check was already there, we were
just performing it after the modulus :-)
15) Some more splice bug fixes from Eric Dumazet, which fix things
mostly eminating from how we now more aggressively use high-order
pages in SKBs.
16) Fix size calculation bug when freeing hash tables in the IPSEC
xfrm code, from Michal Kubecek.
17) Fix PMTU event propagation into socket cached routes, from Steffen
Klassert.
18) Fix off by one in TX buffer release in netxen driver, from Eric
Dumazet.
19) Fix rediculous memory allocation requirements introduced by the
tuntap multiqueue changes, from Jason Wang.
20) Remove bogus AMD platform workaround in r8169 driver that causes
major problems in normal operation, from Timo Teräs.
21) virtio-net set affinity and select queue don't handle
discontiguous cpu numbers properly, fix from Wanlong Gao.
22) Fix a route refcounting issue in loopback driver, from Eric
Dumazet. There's a similar fix coming that we might add to the
macvlan driver as well.
23) Fix SKB leaks in batman-adv's distributed arp table code, from
Matthias Schiffer.
24) r8169 driver gives descriptor ownership back the hardware before
we're done reading the VLAN tag out of it, fix from Francois
Romieu.
25) Checksums not calculated properly in GRE tunnel driver fix from
Pravin B Shelar.
26) Fix SCTP memory leak on namespace exit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
dm9601: support dm9620 variant
SCTP: Free the per-net sysctl table on net exit. v2
net: phy: icplus: fix broken INTR pin settings
net: phy: icplus: Use the RGMII interface mode to configure clock delays
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
sctp: set association state to established in dupcook_a handler
ip6mr: limit IPv6 MRT_TABLE identifiers
r8169: fix vlan tag read ordering.
net: cdc_ncm: use IAD provided by the USB core
batman-adv: filter ARP packets with invalid MAC addresses in DAT
batman-adv: check for more types of invalid IP addresses in DAT
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
net: loopback: fix a dst refcounting issue
virtio-net: reset virtqueue affinity when doing cpu hotplug
virtio-net: split out clean affinity function
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
can: pch_can: fix invalid error codes
can: ti_hecc: fix invalid error codes
can: c_can: fix invalid error codes
r8169: remove the obsolete and incorrect AMD workaround
...
Suravee Suthikulpanit [Thu, 24 Jan 2013 19:17:53 +0000 (13:17 -0600)]
IOMMU, AMD Family15h Model10-1Fh erratum 746 Workaround
The IOMMU may stop processing page translations due to a perceived lack
of credits for writing upstream peripheral page service request (PPR)
or event logs. If the L2B miscellaneous clock gating feature is enabled
the IOMMU does not properly register credits after the log request has
completed, leading to a potential system hang.
BIOSes are supposed to disable L2B micellaneous clock gating by setting
L2_L2B_CK_GATE_CONTROL[CKGateL2BMiscDisable](D0F2xF4_x90[2]) = 1b. This
patch corrects that for those which do not enable this workaround.
Signed-off-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Joerg Roedel <joro@8bytes.org>
David Teigland [Thu, 3 Jan 2013 22:52:07 +0000 (17:52 -0500)]
GFS2: fix skip unlock condition
The recent commit
fb6791d100d1bba20b5cdbc4912e1f7086ec60f8
included the wrong logic. The lvbptr check was incorrectly
added after the patch was tested.
Signed-off-by: David Teigland <teigland@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Peter Korsgaard [Sun, 27 Jan 2013 12:34:22 +0000 (12:34 +0000)]
dm9601: support dm9620 variant
dm9620 is a newer variant of dm9601 with more features (usb 2.0, checksum
offload, ..), but it can also be put in a dm9601 compatible mode, allowing
us to reuse the existing driver.
This does mean that the extended features like checksum offload cannot be
used, but that's hardly critical on a 100mbps interface.
Thanks to Sławek Wernikowski <slawek@wernikowski.net> for providing me
with a dm9620 based device to test.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlad Yasevich [Thu, 24 Jan 2013 16:02:47 +0000 (11:02 -0500)]
SCTP: Free the per-net sysctl table on net exit. v2
Per-net sysctl table needs to be explicitly freed at
net exit. Otherwise we see the following with kmemleak:
unreferenced object 0xffff880402d08000 (size 2048):
comm "chrome_sandbox", pid 18437, jiffies
4310887172 (age 9097.630s)
hex dump (first 32 bytes):
b2 68 89 81 ff ff ff ff 20 04 04 f8 01 88 ff ff .h...... .......
04 00 00 00 a4 01 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<
ffffffff815b4aad>] kmemleak_alloc+0x21/0x3e
[<
ffffffff81110352>] slab_post_alloc_hook+0x28/0x2a
[<
ffffffff81113fad>] __kmalloc_track_caller+0xf1/0x104
[<
ffffffff810f10c2>] kmemdup+0x1b/0x30
[<
ffffffff81571e9f>] sctp_sysctl_net_register+0x1f/0x72
[<
ffffffff8155d305>] sctp_net_init+0x100/0x39f
[<
ffffffff814ad53c>] ops_init+0xc6/0xf5
[<
ffffffff814ad5b7>] setup_net+0x4c/0xd0
[<
ffffffff814ada5e>] copy_net_ns+0x6d/0xd6
[<
ffffffff810938b1>] create_new_namespaces+0xd7/0x147
[<
ffffffff810939f4>] copy_namespaces+0x63/0x99
[<
ffffffff81076733>] copy_process+0xa65/0x1233
[<
ffffffff81077030>] do_fork+0x10b/0x271
[<
ffffffff8100a0e9>] sys_clone+0x23/0x25
[<
ffffffff815dda73>] stub_clone+0x13/0x20
[<
ffffffffffffffff>] 0xffffffffffffffff
I fixed the spelling of sysctl_header so the code actually
compiles. -- EWB.
Reported-by: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Signed-off-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Giuseppe CAVALLARO [Wed, 23 Jan 2013 00:22:37 +0000 (00:22 +0000)]
net: phy: icplus: fix broken INTR pin settings
This patch fixes the setting of the INTR pin that is
valid for IP101 A/G device and not for the IP1001.
Reported-by: Anunay Saxena <anunay.saxena@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stuart Menefy [Wed, 23 Jan 2013 00:22:36 +0000 (00:22 +0000)]
net: phy: icplus: Use the RGMII interface mode to configure clock delays
Like several other PHY devices which support RGMII, the IC+1001 allows
additional delays to by added to the RX_CLK and TX_CLK signals to
compensate for skew between the clock and data signals. Previously this
was always enabled, but this change makes use of the different RGMII
interface modes to allow the user to specify whether this should be
enabled.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar [Wed, 23 Jan 2013 11:45:42 +0000 (11:45 +0000)]
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
Due to IP_GRE GSO support, GRE can recieve non linear skb which
results in panic in case of GRE_CSUM. Following patch fixes it by
using correct csum API.
Bug introduced in commit
6b78f16e4bdde3936b (gre: add GSO support)
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Xufeng Zhang [Wed, 23 Jan 2013 16:44:34 +0000 (16:44 +0000)]
sctp: set association state to established in dupcook_a handler
While sctp handling a duplicate COOKIE-ECHO and the action is
'Association restart', sctp_sf_do_dupcook_a() will processing
the unexpected COOKIE-ECHO for peer restart, but it does not set
the association state to SCTP_STATE_ESTABLISHED, so the association
could stuck in SCTP_STATE_SHUTDOWN_PENDING state forever.
This violates the sctp specification:
RFC 4960 5.2.4. Handle a COOKIE ECHO when a TCB Exists
Action
A) In this case, the peer may have restarted. .....
After this, the endpoint shall enter the ESTABLISHED state.
To resolve this problem, adding a SCTP_CMD_NEW_STATE cmd to the
command list before SCTP_CMD_REPLY cmd, this will set the restart
association to SCTP_STATE_ESTABLISHED state properly and also avoid
I-bit being set in the DATA chunk header when COOKIE_ACK is bundled
with DATA chunks.
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter [Wed, 23 Jan 2013 20:38:34 +0000 (20:38 +0000)]
ip6mr: limit IPv6 MRT_TABLE identifiers
We did this for IPv4 in
b49d3c1e1c "net: ipmr: limit MRT_TABLE
identifiers" but we need to do it for IPv6 as well. On IPv6 the name
is "pim6reg" instead of "pimreg" so there is one less digit allowed.
The strcpy() is in ip6mr_reg_vif().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
françois romieu [Thu, 24 Jan 2013 13:30:06 +0000 (13:30 +0000)]
r8169: fix vlan tag read ordering.
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork [Fri, 25 Jan 2013 23:36:59 +0000 (23:36 +0000)]
net: cdc_ncm: use IAD provided by the USB core
commit 9992c2e (net: cdc_ncm: workaround for missing CDC Union)
added code to lookup an IAD for the interface we are probing.
This is redundant. The USB core has already done the lookup
and saved the result in the USB interface struct. Use that
instead.
Cc: Greg Suarez <gsuarez@smithmicro.com>
Cc: Alexey Orishko <alexey.orishko@stericsson.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller [Mon, 28 Jan 2013 00:10:36 +0000 (19:10 -0500)]
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes ares:
- fix an skb memleak in DAT
- fix the ARP filtering routine in DAT by preventing bogus entries to overwrite
already existing ones in the local cache.
- fix the ARP filtering routine in DAT by preventing it to parse and add to the
cache bogus entries
Signed-off-by: David S. Miller <davem@davemloft.net>
Matthias Schiffer [Thu, 24 Jan 2013 17:18:27 +0000 (18:18 +0100)]
batman-adv: filter ARP packets with invalid MAC addresses in DAT
We never want multicast MAC addresses in the Distributed ARP Table, so it's
best to completely ignore ARP packets containing them where we expect unicast
addresses.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Matthias Schiffer [Thu, 24 Jan 2013 17:18:26 +0000 (18:18 +0100)]
batman-adv: check for more types of invalid IP addresses in DAT
There are more types of IP addresses that may appear in ARP packets that we
don't want to process. While some of these should never appear in sane ARP
packets, a 0.0.0.0 source is used for duplicate address detection and thus seen
quite often.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Matthias Schiffer [Wed, 23 Jan 2013 17:11:53 +0000 (18:11 +0100)]
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
The callers of batadv_dat_snoop_incoming_arp_reply() assume the skb has been
freed when it returns true; fix this by calling kfree_skb before returning as
it is done in batadv_dat_snoop_incoming_arp_request().
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
David S. Miller [Sun, 27 Jan 2013 06:37:22 +0000 (01:37 -0500)]
Merge branch 'for-davem' of git://git./linux/kernel/git/linville/wireless
John W. Linville says:
====================
This is a batch of fixes intende for the 3.8 stream.
Regarding the iwlwifi bits, Johannes says this:
"Please pull to get a single fix from Emmanuel for a bug I introduced due
to misunderstanding the code."
Regarding the mac80211 bits, Johannes says this:
"I have a few small fixes for you:
* some mesh frames would cause encryption warnings -- fixes from Bob
* scanning would pretty much break an association if we transmitted
anything to the AP while scanning -- fix from Stanislaw
* mode injection was broken by channel contexts -- fix from Felix
* FT roaming was broken: hardware crypto would get disabled by it"
Along with that, a handful of other fixes confined to specific drivers.
Avinash Patil fixes a typo in a NULL check in mwifiex.
Larry Finger fixes a build warning in rtlwifi. Seems safe...
Stanislaw Gruszka fixes iwlegacy to prevent microcode errors when
switching from IBSS mode to STA mode.
Felix Fietkau provides a trio of ath9k fixes related to proper tuning.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>