Breno Lima [Tue, 20 Feb 2018 01:19:22 +0000 (01:19 +0000)]
imx: hab: Keep CAAM clock enabled after authenticating additional images
Currently it is not possible to run CMD_DEK on i.MX SPL targets:
=> dek_blob 0x12000000 0x12001000 128
The system hangs after running dek_blob because the CAAM clock is being
disabled by the HAB code. There is no need to disable CAAM clock after
authenticating additional boot images, thus keep CAAM clock enabled to
address this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Maxim Yu. Osipov [Tue, 20 Feb 2018 10:08:09 +0000 (11:08 +0100)]
Revert "mx6: ddr: Allow changing REFSEL and REFR fields"
This reverts commit
edf0093732225c2fd0791c3864e9a3eef1f92f19 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Fabio Estevam [Sat, 17 Feb 2018 21:44:52 +0000 (19:44 -0200)]
mx6sabresd: Select the CONFIG_EFI_PARTITION option
With fastboot support enabled, it is useful to be able to list
the eMMC EFI partitions, so select the CONFIG_EFI_PARTITION option.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Stefano Babic [Mon, 5 Feb 2018 08:33:22 +0000 (09:33 +0100)]
mx6: fix MAINTAINERS for Engicam i.CoreM6 1.5 MIPI
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jagan Teki <jagan@amarulasolutions.com>
Tom Rini [Sat, 17 Feb 2018 21:06:59 +0000 (16:06 -0500)]
Merge git://git.denx.de/u-boot-sh
Marek Vasut [Sat, 17 Feb 2018 01:16:48 +0000 (02:16 +0100)]
ARM: rmobile: Fix broken reset code on Porter
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 17 Feb 2018 01:15:08 +0000 (02:15 +0100)]
ARM: rmobile: Replace SH I2C with IIC on Porter
Get rid of the SH I2C driver on Porter and enable the IIC driver
instead . The old SH I2C is completely broken on Porter anyway
and the DM/DT capable IIC driver allows access to the PMIC too.
Use the DM/DT capable driver instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 17 Feb 2018 01:14:09 +0000 (02:14 +0100)]
ARM: dts: rmobile: Enable I2C6 on Porter
Enable I2C6 bus on Porter to access the PMIC , ie. to reset the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 17 Feb 2018 01:17:40 +0000 (02:17 +0100)]
i2c: rcar_iic: Allow IIC on RCar Gen2
The IIC on Gen2 is compatible with this driver as well, allow it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 17 Feb 2018 00:21:15 +0000 (01:21 +0100)]
ARM: rmobile: Set FDT/initramfs limits on Porter
Set those limits to inform U-Boot about FDT and initramfs placement.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Sat, 17 Feb 2018 00:19:20 +0000 (01:19 +0100)]
ARM: rmobile: Enable convenient commands on Porter
Enable cache and time commands, which are convenience tools for
doing benchmarks and various boot tests. Also enable FIT support
for booting fitImage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Fri, 16 Feb 2018 23:35:23 +0000 (00:35 +0100)]
ARM: rmobile: Reset ethernet PHY
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Marek Vasut [Fri, 16 Feb 2018 23:31:19 +0000 (00:31 +0100)]
ARM: dts: rmobile: Move the u-boot,dm-pre-reloc into u-boot DTS on porter
Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Fri, 16 Feb 2018 18:56:02 +0000 (13:56 -0500)]
Merge git://git.denx.de/u-boot-sh
Tom Rini [Fri, 16 Feb 2018 18:55:51 +0000 (13:55 -0500)]
Merge git://git.denx.de/u-boot-socfpga
Tom Rini [Fri, 16 Feb 2018 18:55:41 +0000 (13:55 -0500)]
Merge git://git.denx.de/u-boot-usb
Goldschmidt Simon [Fri, 9 Feb 2018 20:23:17 +0000 (20:23 +0000)]
env: restore old env_get_char() behaviour
With multiple environments, the 'get_char' callback for env
drivers does not really make sense any more because it is
only supported by two drivers (eeprom and nvram).
To restore single character loading for these drivers,
override 'env_get_char_spec'.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
York Sun [Wed, 7 Feb 2018 22:17:11 +0000 (14:17 -0800)]
env: Fix env_load_location
Commit
7d714a24d725 ("env: Support multiple environments") added
static variable env_load_location. When saving environmental
variables, this variable is presumed to have the value set before.
In case the value was set before relocation and U-Boot runs from a
NOR flash, this variable wasn't writable. This causes failure when
saving the environment. To save this location, global data must be
used instead.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Marek Vasut [Fri, 16 Feb 2018 15:37:46 +0000 (16:37 +0100)]
ARM: rmobile: Enable autocompletion on Gen2
This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Fri, 16 Feb 2018 00:33:27 +0000 (01:33 +0100)]
ARM: rmobile: Convert Porter to SPL
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,
e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Marek Vasut [Fri, 16 Feb 2018 00:33:27 +0000 (01:33 +0100)]
ARM: dts: rmobile: Make PFC and RST available before reloc
Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Fri, 16 Feb 2018 00:33:27 +0000 (01:33 +0100)]
ARM: dts: rmobile: Make scif0 available before reloc on Porter
Make the SCIF available before relocation and in SPL on R8A7791 Porter.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Fri, 16 Feb 2018 00:33:27 +0000 (01:33 +0100)]
serial: Replace CONFIG_ with CONFIG_IS_ENABLED
Cosmetic change, replace CONFIG_* with CONFIG_IS_ENABLED(*) .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Thu, 15 Feb 2018 12:33:37 +0000 (13:33 +0100)]
ARM: rmobile: Enable autocompletion on Gen3
This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Thu, 15 Feb 2018 11:47:23 +0000 (12:47 +0100)]
ARM: rmobile: Enable DTO support on Gen3
Enable support for applying DT overlays on Gen3. This is convenient
for handling extra additional hardware, like ie. the Kingfisher.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Marek Vasut [Tue, 13 Feb 2018 16:21:15 +0000 (17:21 +0100)]
net: ravb: Initialize PHY in probe() once
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Marek Vasut [Thu, 11 Jan 2018 15:28:31 +0000 (16:28 +0100)]
clk: rmobile: Assure SD-IF clock are configured correctly
The SD driver calls clk_set_rate() before clk_enable(), yet clk_set_rate()
implementation in the clock driver does not set the SD-IF divider. Fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tom Rini [Thu, 15 Feb 2018 19:07:04 +0000 (14:07 -0500)]
Merge git://git.denx.de/u-boot-arc
Alexander Graf [Thu, 15 Feb 2018 14:50:54 +0000 (15:50 +0100)]
RPi: Add myself as board maintainer
Commit
958d55f26ce ("MAINTAINERS: Take over BCM2835 maintainership") put
me in as maintainer for the RPi soc, but forgot to update the board
MAINTAINERS file.
Add me there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
Simon Goldschmidt [Tue, 13 Feb 2018 05:34:14 +0000 (06:34 +0100)]
arm: socfpga: use imply instead of select where applicable
Kconfig should only 'select' features that are required for an arch.
Standard features that can be disabled without breaking board support
should use 'imply' instead, to allow users to disable it.
These options are changed for mach-socfpga:
- DM_SPI & DM_SPI_FLASH: only required with QSPI support enabled
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION: the boot rom supports a
partitionless mode also, where SPL is located at address 0
- HW_WATCHDOG: while all mainline board defconfigs use it, U-Boot
should still work without it.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Lukasz Majewski [Tue, 13 Feb 2018 05:34:13 +0000 (06:34 +0100)]
Convert socfpga: select CONFIG_HW_WATCHDOG support for ARCH_SOCFPGA
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Simon Goldschmidt [Mon, 29 Jan 2018 06:36:37 +0000 (07:36 +0100)]
arm: socfpga: fix qspi flash compatible (add "spi-flash")
This patch adds "spi-flash" to the compatible list of the qspi flash
chip for all socfpga boards. This is required to make qspi work on
these boards on top of the recent fixes. Without the "spi-flash"
compatible string for the flash chip, the speed cannot be read and a
speed of 0Hz is used (which results in a divide-by-zero on these
boards).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Alexey Brodkin [Thu, 15 Feb 2018 12:34:58 +0000 (15:34 +0300)]
arc: Fix final linkage with Elf32 tools
ARC Elf32 tools by default enable usage of so-called "small data"
section or in ARC PRM parlance "GP-relative addressing".
The idea is to put up to 2kB of frequently used data into a separate
location and use indirect addressing via dedicated core register (GP).
Where GP is used as a base for offset calculation.
And so if "-msdata" toggle is passed to the compiler either explicitly
or implicitly (that's Elf32 tools case) it will try to put some data
in that "small data" area and then to calculate real offset from GP
to be encoded in instructions we need to know the base value which
liker gets from __SDATA_BEGIN__ symbol in hte linker script.
In U-Boot we don't use that feature and linker script doesn't define
__SDATA_BEGIN__ which gives us the following linkage error if we use
Elf32 tools:
------------------------->8-------------------
LD u-boot
.../bin/arc-elf32-ld.bfd: Error: Linker symbol __SDATA_BEGIN__ not found
.../bin/arc-elf32-ld.bfd: final link failed: Bad value
------------------------->8-------------------
Note if uClibc or glibc tools are used that problem doesn't happen
because usage of "small data section" is disabled by default as not very
useful for bigger executables. Moreover GP is just another name of r26
so we're loosing 1 core register which is not used by the compiler as a
generic register with "-msdata".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Faiz Abbas [Thu, 15 Feb 2018 11:42:11 +0000 (17:12 +0530)]
usb: host: xhci-omap: Remove redundant board_usb_init and board_usb_cleanup functions
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Alexey Brodkin [Wed, 31 Jan 2018 14:56:59 +0000 (17:56 +0300)]
usb: dwc2: Rename CONFIG_DWC2_UTMI_PHY_WIDTH to CONFIG_DWC2_UTMI_WIDTH
For some reason from day one we used to have both CONFIG_DWC2_UTMI_WIDTH
mentioned in dwc2.h and in scripts/config_whitelist.txt but never really used
and CONFIG_DWC2_UTMI_PHY_WIDTH used in real code in dwc2.c (but never
defined).
Moreover even though CONFIG_DWC2_UTMI_WIDTH might be either 8 or 16
depending on hardware (and the same is said in a comment for it in
dwc2.h) but then 8 is hardcoded in the header leaving no ability to
override this value in board's configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Lukasz Majewski [Fri, 9 Feb 2018 22:53:29 +0000 (23:53 +0100)]
Convert CONFIG_SYS_BOOTCOUNT_SINGLEWORD to Kconfig
This converts the following to Kconfig:
CONFIG_SYS_BOOTCOUNT_SINGLEWORD
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
Lukasz Majewski [Fri, 9 Feb 2018 22:50:57 +0000 (23:50 +0100)]
Convert CONFIG_BOOTCOUNT_LIMIT to Kconfig
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_LIMIT
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tom Rini [Wed, 14 Feb 2018 20:46:14 +0000 (15:46 -0500)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 15 Feb 2018 02:34:05 +0000 (21:34 -0500)]
Revert "drivers/ddr/fsl: Dual-license DDR driver"
Upon further review, not all code authors are in favour of this change.
This reverts commit
ee3556bcafbb05e59aabdc31368984e76acaabc4.
Signed-off-by: Tom Rini <trini@konsulko.com>
Simon Goldschmidt [Wed, 14 Feb 2018 05:44:36 +0000 (06:44 +0100)]
spl: unbreak CONFIG_SPL_MULTI_DTB_FIT after fixing CONFIG_OF_EMBED
With commit
9bd76b807636 ("spl: make CONFIG_OF_EMBED pass dts through
fdtgrep"), CONFIG_SPL_MULTI_DTB_FIT has been broken because
cmd_fdtgrep was now unknown in scripts/Makefile.spl after moving
it to dts/Makefile. This bug has been introduced with v2018.01.
This patch moves cmd_fdtgrep from dts/Makefile to scripts/Makefile.lib
and includes scripts/Makefile.lib in scripts/Makefile.spl.
Fixes:
9bd76b807636 ("spl: make CONFIG_OF_EMBED pass dts through fdtgrep")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Heinrich Schuchardt [Wed, 14 Feb 2018 07:05:44 +0000 (08:05 +0100)]
cmd: scsi: move CMD_SCSI to device access commands
Configuration option CMD_SCSI should be placed in the same submenu as
CMD_SATA and CMD_MMC.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Andre Heider [Fri, 9 Feb 2018 07:10:22 +0000 (08:10 +0100)]
arm/PSCI: support PSCI versions greater than 1.0
ATF recently began announcing PSCI v1.1. Since that version is unknown
to u-boot, the PSCI device nodes were not updated.
Switch from the case statement to a greater/less-than comparison so that
v1.1, as well as future versions, get at least the compatible nodes of
known versions.
PSCI v1.1 doesn't seem to have introduced a new corresponding compatible.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Alex Kiernan [Sun, 11 Feb 2018 17:16:46 +0000 (17:16 +0000)]
Fix --noheader on fw_printenv
The single argument `--noheader' is expecting isn't taken from getopt
parsing, but instead from the remaining argv arguments.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Sam Protsenko [Wed, 7 Feb 2018 18:41:32 +0000 (20:41 +0200)]
am335x_evm: Consolidate eMMC partitions with DFU info
>From DFU_ALT_INFO_EMMC (include/environment/ti/dfu.h) we can see that
rootfs will be flashed to second partition on eMMC. But at the moment we
have only one partition in $partitions environment variable. Let's add
"bootloader" partition prior to "rootfs", so that DFU works correctly.
This also fixes eMMC boot, which looks for rootfs on second partition.
"bootloader" partition start corresponds to "u-boot.img.raw" in DFU
eMMC info, which is 0x300 sector (384 KiB offset from eMMC start).
rootfs start address can be also found from DFU eMMC info.
bootloader-related area is finished at 0x1500 sector (2688 KiB offset
from eMMC start). This should be the start address for rootfs in
$partitions environment variable.
While at it, fix U-Boot environment address to be the same as for
AM57x EVM, so that it doesn't clash with other partitions.
So now eMMC layout looks like this:
===============================================================
0 +------------------------+
| MBR/GPT header | 128 -
128 +------------------------+
| MLO | 256 -
384 +------------------------+
| u-boot.img | 1792 bootloader
2176 +------------------------+
| //////// hole //////// | 256 -
2432 +------------------------+
| U-Boot environment | 128 -
2560 +------------------------+
| U-Boot environment | 128 -
| (redundant) |
2688 +------------------------+
| rootfs | remaining rootfs
end +------------------------+
===============================================================
"hole" area can be used further for storing U-Boot environment (like
it's done in AM57x EVM config file) or for increasing u-boot.img area
(in case u-boot.img size increased, e.g. if new dtbs were added).
This commit conforms with Linux partition table from
f6d245b8c56c
("arm: am57xx: Fix Linux boot from eMMC") commit, making things in
uniform way.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 6 Feb 2018 17:15:38 +0000 (12:15 -0500)]
configs: Migrate CONFIG_SPL_FRAMEWORK
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 6 Feb 2018 17:15:37 +0000 (12:15 -0500)]
configs: Drop unused CONFIG_SPL_MMC_MINIMAL
The option CONFIG_SPL_MMC_MINIMAL is unused in code, drop it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Faiz Abbas [Tue, 6 Feb 2018 13:45:59 +0000 (19:15 +0530)]
configs: am335x_evm: Add DYNAMIC_CRC_TABLE
Add CONFIG_DYNAMIC_CRC_TABLE to am335x_evm_defconfig to reduce the
size of the image.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Tue, 6 Feb 2018 13:45:58 +0000 (19:15 +0530)]
lib: Kconfig: Move DYNAMIC_CRC_TABLE to Kconfig
Add CONFIG prefix to DYNAMIC_CRC_TABLE and implement it in
Kconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Faiz Abbas [Mon, 5 Feb 2018 13:52:29 +0000 (19:22 +0530)]
configs: am335x_evm: Disable ISO and EFI partitions in SPL
ISO and EFI partition configs in SPL are selected by default.
However, they are not being used.
Therefore, remove ISO and EFI partition support in SPL.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simon Goldschmidt [Tue, 13 Feb 2018 12:18:00 +0000 (13:18 +0100)]
arm: update Kconfig help for ENABLE_ARM_SOC_BOOT0_HOOK
When this config is enabled, <asm/arch/boot0.h> is included,
but the Kconfig help says this should be a define
(ARM_SOC_BOOT0_HOOK).
The code for this in arch/arm/lib/vectors.s was changed on
01/02/2017 with commit
ce62e57fc571 ("ARM: boot0 hook: remove macro,
include whole header file").
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Masahiro Yamada [Tue, 13 Feb 2018 02:32:15 +0000 (11:32 +0900)]
ARM: image: indent with tab instead of 4 spaces
Commit
6808ef9ac2a6 ("move booti_setup to arch/arm/lig/image.c")
not only moved the code, but also replaced a tab with 4 spaces
to break the Linux coding style.
Restore tab indentation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Chen <bin.chen@linaro.org>
Masahiro Yamada [Tue, 13 Feb 2018 03:10:02 +0000 (12:10 +0900)]
cmd: booti: fix invalid image address in debug message
With commit
6808ef9ac2a6 ("move booti_setup to arch/arm/lig/image.c"),
images->ep has not been set at this point.
Fixes:
6808ef9ac2a6 ("move booti_setup to arch/arm/lig/image.c")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Chen <bin.chen@linaro.org>
Heinrich Schuchardt [Mon, 12 Feb 2018 11:55:28 +0000 (12:55 +0100)]
efi_driver: comment struct efi_driver_ops
Provide description for struct efi_driver_ops.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Heinrich Schuchardt [Mon, 12 Feb 2018 11:38:36 +0000 (12:38 +0100)]
dm: core: fix typo in comment (device.h)
%s/Indentiies/Identifies/g
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Simon Goldschmidt [Tue, 13 Feb 2018 12:18:27 +0000 (13:18 +0100)]
fix spelling of 'functions' in 2 places (was 'funtcions')
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Tom Rini [Mon, 12 Feb 2018 14:51:33 +0000 (09:51 -0500)]
SystemACE: Remove
This driver is no longer used on any supported platform in U-Boot and
there is no interest in maintaining it further from people that have
used it historically.
Cc: Simon Glass <sjg@chromium.org>
Cc: Michal Simek <michal.simek@xilinx.com>
c: Alexey Brodkin <alexey.brodkin@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:23 +0000 (02:42 +0200)]
spi: Migrate CONFIG_CF_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:22 +0000 (02:42 +0200)]
spi: Migrate CONFIG_KIRKWOOD_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:21 +0000 (02:42 +0200)]
spi: Migrate CONFIG_LPC32XX_SSP to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:20 +0000 (02:42 +0200)]
spi: Migrate CONFIG_MPC8XXX_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:19 +0000 (02:42 +0200)]
spi: Migrate CONFIG_MXC_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:18 +0000 (02:42 +0200)]
spi: Migrate CONFIG_MXS_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:17 +0000 (02:42 +0200)]
spi: Migrate CONFIG_SH_QSPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Tuomas Tynkkynen [Wed, 7 Feb 2018 00:42:16 +0000 (02:42 +0200)]
spi: Migrate CONFIG_SH_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Max Filippov [Wed, 7 Feb 2018 23:30:03 +0000 (15:30 -0800)]
.travis.yml: test xtensa xtfpga board in QEMU
This allows running tests on emulated KC705 board with DC233C xtensa
core. It expects to find conf.xtfpga_qemu in the uboot-test-hooks.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Max Filippov [Wed, 7 Feb 2018 23:30:02 +0000 (15:30 -0800)]
xtfpga: enable hush parser
Remove CONFIG_BOOT_RETRY_TIME as it doesn't do much good and enable
CONFIG_HUSH_PARSER in xtfpga_defconfig.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Max Filippov [Wed, 7 Feb 2018 23:30:01 +0000 (15:30 -0800)]
.travis.yml: download xtensa prebuilt toolchain
xtensa toolchains are core-specific, so give full toolchain name and
download corresponding prebuilt toolchain from the github release.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Bin Meng [Mon, 12 Feb 2018 09:54:37 +0000 (17:54 +0800)]
microblaze: bootm: Fix compiler warning
Fix build warning in arch/microblaze/lib/bootm.c with gcc 7.3.0:
warning: this 'if' clause does not guard... [-Wmisleading-indentation]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Bin Meng [Mon, 12 Feb 2018 09:54:36 +0000 (17:54 +0800)]
arm: omap2: Fix compiler warning
Fix build warning in arch/arm/mach-omap2/emif-common.c and
arch/arm/mach-omap2/omap4/emif.c with gcc 7.3.0:
warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Bin Meng [Mon, 12 Feb 2018 09:54:35 +0000 (17:54 +0800)]
video: ivybridge_igd: Fix compiler warning
Fix build warning in drivers/video/ivybridge_igd.c with gcc 7.3.0:
warning: 'ivb_pm_gt2' defined but not used [-Wunused-const-variable=]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 10 Feb 2018 15:22:07 +0000 (16:22 +0100)]
tftp: update: Include missing cfi_flash.h header
Add the missing header, otherwise CONFIG_SYS_MAX_FLASH_BANKS
may be undeclared.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 10 Feb 2018 15:22:06 +0000 (16:22 +0100)]
cmd: fitupd: Convert CONFIG_UPDATE_TFTP and co.
Convert the CONFIG_UPDATE_TFTP and related symbols to Kconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Marek Vasut [Sat, 10 Feb 2018 15:22:05 +0000 (16:22 +0100)]
cmd: fitupd: Convert CONFIG_CMD_FITUPD
Convert the CONFIG_CMD_FITUPD symbol to Kconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Tom Rini [Tue, 13 Feb 2018 15:51:00 +0000 (10:51 -0500)]
Merge git://git.denx.de/u-boot-rockchip
Philipp Tomsich [Fri, 2 Feb 2018 11:01:44 +0000 (12:01 +0100)]
spl: fit: move fdt_record_loadable out of ARCH_FIXUP_FDT_MEMORY guard
The fdt_record_loadable()-function was wedged between other functions
that were guarded by ARCH_FIXUP_FDT_MEMORY. This could lead to linker
errors on some configurations.
With this change, fdt_record_loadable() is moved out of the
ARCH_FIXUP_FDT_MEMORY guard (plus I tried to retain alphabetical
ordering for functions by placing it appropriately).
References: 9f45aeb ("spl: fit: implement fdt_record_loadable")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reported-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Heinrich Schuchardt [Tue, 30 Jan 2018 23:45:51 +0000 (00:45 +0100)]
rockchip: gpio: remove dead code
In the following statements
if (a) return a; if (a) return c;
the second return can never be executed.
Identified by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tom Rini [Mon, 12 Feb 2018 23:52:31 +0000 (18:52 -0500)]
Prepare v2018.03-rc2
Signed-off-by: Tom Rini <trini@konsulko.com>
Alex Kiernan [Wed, 7 Feb 2018 20:01:54 +0000 (20:01 +0000)]
Fix misaligned buffer in env_fat_save
When saving the environment on a platform which has DMA alignment
larger than the natural alignment, env_fat_save triggers a debug
message in file_fat_write:
Saving Environment to FAT... writing uboot.env
FAT: Misaligned buffer address (
9df1c8e0)
OK
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Tom Rini [Mon, 12 Feb 2018 17:08:32 +0000 (12:08 -0500)]
Merge git://git.denx.de/u-boot-fsl-qoriq
Tom Rini [Sat, 3 Feb 2018 17:10:38 +0000 (12:10 -0500)]
configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sun, 11 Feb 2018 01:27:45 +0000 (20:27 -0500)]
configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Sat, 10 Feb 2018 22:04:13 +0000 (17:04 -0500)]
Merge tag 'signed-efi-v2018.03' of git://github.com/agraf/u-boot
Patch queue for efi in 2018.03 - 2018-02-10
This time we have a few important bug fixes. Most noticable are:
- Fix OpenBSD loader with CONFIG_BLK=n
- Fix builds on various circumstances
- Add missing stubs so callers don't call NULL
- Bump UEFI revision to 2.7
Heinrich Schuchardt [Fri, 9 Feb 2018 19:55:47 +0000 (20:55 +0100)]
efi_loader: correct efi_disk_register
efi_disk_register should return as status code (efi_status_t).
Disks with zero blocks should be reported as 'not ready' without throwing
an error.
This patch solves a problem running OpenBSD on system configured with
CONFIG_BLK=n (e.g. i.MX6).
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Fri, 9 Feb 2018 19:41:21 +0000 (20:41 +0100)]
efi_loader: add missing runtime services stubs
Add stubs for UpdateCapsule, QueryCapsuleCapabilities, and
QueryVariableInfo.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Tue, 30 Jan 2018 19:03:02 +0000 (20:03 +0100)]
efi_loader: split README.efi into two separate documents
README.efi describes two different concepts:
* U-Boot exposing the UEFI API
* U-Boot running on top of UEFI.
This patch splits the document in two.
Religious references are removed.
The separation of the concepts makes sense before detailing the internals
of U-Boot exposing the UEFI API in a future patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Thu, 1 Feb 2018 11:53:32 +0000 (12:53 +0100)]
efi_driver: return type of efi_driver_init()
Change the return type of efi_driver_init() to efi_status_t.
efi_driver_init() calls efi_add_driver() which returns an efi_status_t
value. efi_driver_init() should not subject this value to a conversion to
int losing high bits on 64bit systems.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Mon, 5 Feb 2018 17:04:21 +0000 (18:04 +0100)]
efi_loader: do not use 2.0.5 as UEFI revision number
Currently the UEFI revision number in the system table header is set to
2.0.5. This version number does not refer to any existing version of the
UEFI standard.
Set the revision number to 2.7.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Sun, 4 Feb 2018 22:05:13 +0000 (23:05 +0100)]
efi_loader: create stub for CreateEventEx
Currently we set the function pointer for the CreateEventEx boot service
to NULL. When called this would lead to an immediate failure.
A function stub is provided which handles the case that the boot service
is called without an event group and returns EFI_UNSUPPORTED otherwise.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Fri, 2 Feb 2018 00:05:47 +0000 (01:05 +0100)]
efi_selftest: use correct compiler flags for miniapps
For EFI binaries we need special CFLAGS.
They were specified for an object file that since has been replaced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Tue, 30 Jan 2018 18:47:43 +0000 (19:47 +0100)]
efi_loader: fix the online help for bootefi bootmgr
The bootefi command is missing in the online help for
bootefi bootmgr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Heinrich Schuchardt [Wed, 31 Jan 2018 18:45:35 +0000 (18:45 +0000)]
efi_loader: fix building crt0 on arm
Before the patch an undefined constant EFI_SUBSYSTEM was used in the
crt0 code. The current version of binutils does not swallow the error.
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=888403
The necessary constant IMAGE_SUBSYSTEM_EFI_APPLICATION is already
defined in pe.h. So let's factor out asm-generic/pe.h for the
image subsystem constants and use it in our assembler code.
IMAGE_SUBSYSTEM_SAL_RUNTIME_DRIVER does not exist in the specification
let's use IMAGE_SUBSYSTEM_EFI_ROM instead.
The include pe.h is only used in code maintained by Alex so let him be the
maintainer here too.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
York Sun [Wed, 7 Feb 2018 19:47:22 +0000 (11:47 -0800)]
drivers/ddr/fsl: Dual-license DDR driver
To make this driver easier to be reused, dual-license DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Simon Glass <sjg@chromium.org>
CC: Tom Rini <trini@konsulko.com>
CC: Heinrich Schuchardt <xypron.glpk@gmx.de>
CC: Thomas Schaefer <thomas.schaefer@kontron.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Robert P. J. Day <rpjday@crashcourse.ca>
CC: Alexander Merkle <alexander.merkle@lauterbach.com>
CC: Joakim Tjernlund <joakim.tjernlund@transmode.se>
CC: Curt Brune <curt@cumulusnetworks.com>
CC: Valentin Longchamp <valentin.longchamp@keymile.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Ira W. Snyder <iws@ovro.caltech.edu>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Kyle Moffett <Kyle.D.Moffett@boeing.com>
CC: Sebastien Carlier <sebastien.carlier@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Peter Tyser <ptyser@xes-inc.com>
CC: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Zhao Qiang [Wed, 7 Feb 2018 02:01:56 +0000 (10:01 +0800)]
PowerPC: phy: enable all phylib drivers when use phylib and tsec enet
config_phylib_all_drivers.h should be included when CONFIG_PHYLIB and
CONFIG_TSEC_ENET are defined.
Fixes:
3146f0c017 ("Move PHYLIB to Kconfig")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Lukas Auer [Thu, 25 Jan 2018 13:11:17 +0000 (14:11 +0100)]
crypto/fsl: instantiate all rng state handles
Extend the instantiate_rng() function and the corresponding CAAM job
descriptor to instantiate all RNG state handles. This moves the RNG
instantiation code in line with the CAAM kernel driver.
Previously, only the first state handle was instantiated. The second
one was instantiated by the CAAM kernel driver. This works if the
kernel runs in secure mode, but fails in non-secure mode since the
kernel driver uses DEC0 directly instead of over the job ring
interface. Instantiating all RNG state handles in u-boot removes the
need for using DEC0 in the kernel driver, making it possible to use
the CAAM in non-secure mode.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Vinitha Pillai-B57223 [Tue, 9 Jan 2018 17:33:42 +0000 (23:03 +0530)]
armv8: ls1012ardb: Add distro secure boot support
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
qspi boot in case of secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sriram Dash [Tue, 30 Jan 2018 10:28:44 +0000 (15:58 +0530)]
armv8: Remove dependency of SERDES for LSCH2 and LSCH3
Remove dependency of SYS_HAS_SERDES for Layerscape Chasis 2 and
Layerscape Chasis 3.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rajat Srivastava [Fri, 2 Feb 2018 12:22:07 +0000 (17:52 +0530)]
armv8: ls1088a: qspi: Enable XIP mode above 16 MB addresses
Currently in LS1088A, XIP mode in QSPI works up to 16 MB
addresses. This patch enables QSPI support in XIP mode for
addresses above 16 MB as well.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Hou Zhiqiang [Mon, 5 Feb 2018 05:46:47 +0000 (13:46 +0800)]
ARMv8: ls1046a: Enable PCIe and E1000 in lpuart defconfig
Enable PCIe and E1000 in ls1046aqds lpuart defconfig.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adam Ford [Tue, 6 Feb 2018 18:43:56 +0000 (12:43 -0600)]
Move most CONFIG_HAVE_BLOCK_DEVICE to Kconfig
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Tom Rini [Thu, 8 Feb 2018 18:49:48 +0000 (13:49 -0500)]
block: Migrate SystemACE chip to Kconfig
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.
Cc: Alexey Brodkin <alexey.brodkin@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.