Lubomir Rintel [Sun, 19 Apr 2020 17:11:43 +0000 (19:11 +0200)]
ARM: dts: kirkwood: Fix interrupt controller node name
The current ones makes validation unhappy:
kirkwood-lsxhl.dt.yaml: main-interrupt-ctrl@20200: $nodename:0:
'main-interrupt-ctrl@20200' does not match
'^interrupt-controller(@[0-9a-f,]+)*$'
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 21:16:36 +0000 (23:16 +0200)]
Merge tag 'v5.8-rockchip-dts32-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
RGA node for rk322x, wifi node for rk3229-xms6 and some cleanups.
* tag 'v5.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add rga node for rk322x
ARM: dts: remove disable-wp from rk3229-xms6 emmc
ARM: dts: enable WLAN for Mecer Xtreme Mini S6
ARM: dts: rockchip: remove identical #include from rk3288.dtsi
ARM: dts: rockchip: rename and label gpio-led subnodes
Link: https://lore.kernel.org/r/3735080.6Cexqc3t0Y@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 21:14:10 +0000 (23:14 +0200)]
Merge tag 'v5.8-rockchip-dts64-1' of git://git./linux/kernel/git/mmind/linux-rockchip into arm/dt
New soc variant the rk3326 which is essentially a px30 with only one
display controller and a new board using it, the Odroid Advance Go.
sdcard regulator for the rockpro64 and a lot of devicetree fixes
making the dt-binding check a lot happier.
* tag 'v5.8-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (22 commits)
arm64: dts: rockchip: fix pinctrl-names for gpio-leds node on rk3326-odroid-go2
arm64: dts: rockchip: fix pd_tcpc0 and pd_tcpc1 node position on rk3399
arm64: dts: rockchip: add bus-width properties to mmc nodes for px30
arm64: dts: rockchip: remove disable-wp from rk3308-roc-cc emmc node
arm64: dts: rockchip: rename and label gpio-led subnodes
arm64: dts: rockchip: fix defines in pd_vio node for rk3399
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-orangepi
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-orangepi
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-nanopi4
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-nanopi4
arm64: dts: rockchip: fix rtl8211f nodename for rk3328 Beelink A1
arm64: dts: rockchip: fix phy nodename for rk3328
include: dt-bindings: rockchip: remove unused defines
arm64: dts: rockchip: replace RK_FUNC defines in rk3326-odroid-go2
arm64: dts: rockchip: Define the rockchip Video Decoder node on rk3399
arm64: dts: rockchip: remove #sound-dai-cells from &spdif node of rk3399-hugsun-x99.dts
arm64: dts: rockchip: remove #sound-dai-cells from &i2s1 node of rk3399-pinebook-pro.dts
arm64: dts: rockchip: add Odroid Advance Go
dt-bindings: Add binding for Hardkernel Odroid Go Advance
arm64: dts: rockchip: add core devicetree for rk3326
...
Link: https://lore.kernel.org/r/1970481.V9vR1fIhX2@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 21:10:17 +0000 (23:10 +0200)]
Merge tag 'mvebu-dt64-5.8-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt64 for 5.8 (part 1)
Armada 3720 based SoC:
+ Fix PCIe support allowing to use Compex wifi cards
+ Turris MOX board:
- fix SFP binding
- forbid SDR104 on SDIO to pass electromagnetic interference certifications
+ uDPU board: add i2c recovery support
Armada 8040 based SoC: SolidRun 8040: update phy interface
* tag 'mvebu-dt64-5.8-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: armada-3720-turris-mox: fix SFP binding
arm64: dts: armada-3720-turris-mox: forbid SDR104 on SDIO for FCC purposes
arm64: dts: add uDPU i2c bus recovery
arm64: dts: marvell: drop i2c timeout-ms property
arm64: dts: marvell: armada-37xx: Move PCIe max-link-speed property
arm64: dts: marvell: armada-37xx: Move PCIe comphy handle property
arm64: dts: marvell: armada-37xx: Set pcie_reset_pin to gpio function
arm64: dts: update SolidRun Armada 8040 phy interface types
Link: https://lore.kernel.org/r/878shmeffd.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 21:09:18 +0000 (23:09 +0200)]
Merge tag 'mvebu-dt-5.8-1' of git://git.infradead.org/linux-mvebu into arm/dt
mvebu dt for 5.8 (part 1)
Add LCP panel support on ReadyNAS NV+v2
Add new board: Check Point L-50, kirkwood based SoC router
Remove unused property 'timeout-ms' in i2c nodes
* tag 'mvebu-dt-5.8-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood: ReadyNAS NV+v2: Add LCD panel
ARM: dts: kirkwood: Add Check Point L-50 board
ARM: dts: marvell: drop i2c timeout-ms property
Link: https://lore.kernel.org/r/87blmiefgw.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 21:07:21 +0000 (23:07 +0200)]
Merge tag 'juno-updates-5.8' of git://git./linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv8 Juno/Vexpress/Fast Models updates for v5.8
Various miscellaneous device tree source fixes to make them fully
binding compliant. It includes fixing various device node names,
order of interrupt properties, compatible names, address and size
cell fields and their aligment with children nodes as well as
moving some fixed devices out of bus node.
* tag 'juno-updates-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm64: dts: juno: Fix SCPI shared mem node name
arm64: dts: vexpress: Fix VExpress LED names
arm64: dts: juno: Fix GPU interrupt order
arm64: dts: fvp/juno: Fix bus node names
arm64: dts: fvp: Fix SMMU DT node
arm64: dts: fvp/juno: Fix serial node names
arm64: dts: juno: Use proper DT node name for USB
arm64: dts: fvp: Fix ITS node names and #msi-cells
arm64: dts: fvp: Fix GIC child nodes
arm64: dts: juno: Fix GIC child nodes
arm64: dts: fvp: Fix GIC compatible names
arm64: dts: juno: Fix mem-timer
arm64: dts: juno: Move fixed devices out of bus node
arm64: dts: fvp: Move fixed clocks out of bus node
arm64: dts: vexpress: Move fixed devices out of bus node
arm64: dts: fvp: Move fixed devices out of bus node
arm64: dts: fvp/juno: Fix node address fields
Link: https://lore.kernel.org/r/20200519094702.GA32975@bogus
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 21:06:20 +0000 (23:06 +0200)]
Merge tag 'qcom-dts-for-5.8' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM dts updates for v5.8
This adds SCM firmware node for IPQ806x and fixes the high resolution
timer for IPQ4019. Samsung Galaxy S5 gains regulators, eMMC and USB
support.
* tag 'qcom-dts-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: msm8974-klte: Add max77826 pmic node
ARM: dts: qcom: msm8974-klte: Add USB node
ARM: dts: qcom: msm8974-klte: Add sdhci1 node
ARM: dts: qcom: msm8974-klte: Add gpio-keys nodes
ARM: dts: qcom: msm8974-klte: Remove inherited vreg_boost node
ARM: dts: qcom: msm8974-klte: Add pma8084 regulator nodes
ARM: dts: qcom: ipq4019: fix high resolution timer
ARM: dts: qcom: add scm definition to ipq806x
Link: https://lore.kernel.org/r/20200519052538.1250076-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:50:40 +0000 (22:50 +0200)]
Merge tag 'qcom-arm64-for-5.8' of git://git./linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM64 DT updates for v5.8
For SDM845 this defines the IPA network accelerator and the CCI camera
control bus, it defines the required UFS reset and adds WiFi for the
Lenovo Yoga C630 and defines GPIO pin names and adds OV8856 and OC7251
camera nodes for DB845c.
For SC7180 it adds GPU support, defines the modem remoteproc, adds the
IPA network accelerator, Coresight and ETM support, adds cpuidle low
power states and updates the CPUs' compatible.
For SM8250 it adds regulators from the PM8150, PM8150L and PM8009 and
adds voltage corners, it defines the nodes for UFS PHY and controller
and finally corrects a typo in the PDC node to make SPMI functional.
For MSM8916 I2C1 and I2C5 are defined, a node for the CCI camera control
interface bus is added and Coresight is disabled by default to match
some product configurations. The Samsung A3U gained display support and
Samsung A5U gained touchscreen support.
MSM8996 now property describes the power supply chain for the GPU, the
CCI camera control interface bus is added and the DB820c has the
regulators of the secondary PMIC defined.
For QCS404 USB PHYs and controllers are defined and wired up for the
EVB.
SDM630/SDM660 platform support is added and the Xiaomi Redmi Note 7
defined.
It also contains a number of changes throughout to improve DT binding
compliance.
* tag 'qcom-arm64-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (68 commits)
arm64: dts: qcom: sc7180: Correct the pdc interrupt ranges
arm64: dts: qcom: sc7180: add IPA information
arm64: dts: qcom: sc7180: Fix ETMv4 power management patch
arm64: dts: qcom: sc7180: Add A618 gpu dt blob
dt-bindings: arm-smmu: Add sc7180 compatible string
arm64: dts: qcom: msm8996: Make GPU node control GPU_GX GDSC
arm64: dts: qcom: db820c: Add vdd_gfx and tie it into mmcc
arm64: dts: qcom: apq8016-sbc: merge -pins.dtsi into main .dtsi
arm64: dts: qcom: msm8916: move gpu opp table to gpu node
arm64: dts: qcom: msm8916: avoid using _ in node names
arm64: dts: qcom: c630: Specify UFS device reset
arm64: dts: qcom: c630: Add WiFi node
arm64: dts: qcom: msm8916-samsung-a3u: add nodes for display panel
arm64: dts: qcom: db820c: Fix invalid pm8994 supplies
arm64: dts: qcom: db820c: Add pmi8994 RPM regulators
arm64: dts: qcom: msm8916: Disable coresight by default
arm64: dts: qcom: sc7180: Add "no-map" to cmd_db reserved area
arm64: dts: qcom: msm8916-samsung-a5u: Add touchscreen
arm64: dts: qcom: msm8916-samsung-a2015: Add touchscreen regulator
arm64: dts: qcom: msm8916: Add blsp_i2c5
...
Link: https://lore.kernel.org/r/20200519052528.1249950-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:49:06 +0000 (22:49 +0200)]
Merge tag 'at91-5.8-dt' of git://git./linux/kernel/git/at91/linux into arm/dt
AT91 DT for 5.8
- New board: Microchip SAMA5D2 Industrial Connectivity Platform
- All SoCs are now converted to the new PMC device tree binding
- sama5d2 flexcom nodes are now fully described in sama5d2.dtsi
* tag 'at91-5.8-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/at91/linux: (35 commits)
ARM: dts: at91: sama5d2_xplained: Add aliases for the dedicated I2C IPs
ARM: dts: at91: Configure I2C SCL gpio as open drain
ARM: dts: at91: sama5d2_xplained: Describe the flx0 I2C function
ARM: dts: at91: sama5d2_ptc_ek: Add comments to describe the aliases
ARM: dts: at91: sama5d2_xplained: Add alias for DBGU
ARM: dts: at91: sama5d2: Add missing flexcom definitions
ARM: dts: at91: sama5d2: Remove i2s and tcb aliases from SoC dtsi
ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and I2C flx0 functions
ARM: dts: at91: sama5d2: Add DMA bindings for the flx1 I2C function
ARM: dts: at91: sama5d2: Add DMA bindings for the flx3 SPI function
ARM: dts: at91: sama5d2: Add DMA bindings for the SPI and UART flx4 functions
ARM: dts: at91: sama5d2: Specify the FIFO size for the Flexcom UART
ARM: dts: at91: sama5d2: Move flx0 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx1 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx2 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx3 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Move flx4 definitions in the SoC dtsi
ARM: dts: at91: sama5d2: Fix the label numbering for flexcom functions
ARM: dts: at91: sama5d27_wlsom1: Add alias for i2c0
ARM: dts: at91: sama5d2-icp: add SAMA5D2-ICP
...
Link: https://lore.kernel.org/r/20200518212844.GA26356@piout.net
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:48:15 +0000 (22:48 +0200)]
Merge tag 'uniphier-dt64-v5.8' of git://git./linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM64 SoC DT updates for v5.8
- add DMA controller nodes
- add Akebi96 board support
* tag 'uniphier-dt64-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
arm64: dts: uniphier: Add support for Akebi96
dt-bindings: arm: Add Akebi96 board support
arm64: dts: uniphier: add #address-cells and #size-cells to SPI nodes
arm64: dts: uniphier: Stabilize Ethernet RGMII mode of PXs3 ref board
arm64: dts: uniphier: Add ethernet aliases
arm64: dts: uniphier: Add XDMAC node
Link: https://lore.kernel.org/r/CAK7LNARUL52pBhg8AD9XeScVqhD8qr2eVEfu4+1v8D+KPyOwNw@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:47:19 +0000 (22:47 +0200)]
Merge tag 'uniphier-dt-v5.8' of git://git./linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.8
- add DMA controller nodes
* tag 'uniphier-dt-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: add #address-cells and #size-cells to SPI nodes
ARM: dts: uniphier: Add ethernet aliases
ARM: dts: uniphier: Add XDMAC node
Link: https://lore.kernel.org/r/CAK7LNAQXSpg4s0e0d-tp9j85Sj01t13zAa5+rqsOWu4ZvkpYhg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:41:59 +0000 (22:41 +0200)]
Merge tag 'v5.7-next-dts64' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
MT2712:
- replace deprecated compatible for the usb PHY
MT6797:
- switch to SPDX identifier
- add and enable I2C device for x20 development board
- add I2C compatible to the binding description
MT7622:
- add Wi-Fi device and enable it for the Bananpi-R64
MT8173:
- add CPU capacities based on Dhryston benchmark
- fix DT build warnings
- set throtteling range to limitless
- add Elm and Hana devices on which several chromebooks are based
- add Global Command Queue entries to the users
MT8183:
- split cpuidle states in two as the clusters have different target residencies
* tag 'v5.7-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: mt8173: Add capacity-dmips-mhz attributes
arm64: dts: mt2712: use non-empty ranges for usb-phy
arm64: dts: mt8173: fix mdp aliases property name
arm64: dts: mediatek: Switch to SPDX license identifier for MT6797 SoC
arm64: dts: mediatek: Enable I2C support for 96Boards X20 Development board
arm64: dts: mediatek: Add I2C support for MT6797 SoC
dt-bindings: i2c: Document I2C controller binding for MT6797 SoC
arm64: dts: mt8173: fix cooling device range
arm64: dts: mediatek: add mt8173 elm and hana board
arm64: dts: mt8173: fix unit name warnings
arm64: dts: mt8173: add uart aliases
dt-bindings: arm64: dts: mediatek: Add mt8173 elm and hana
arm64: dts: mt8183: adjust cpuidle target residency
arm64: dts: mt8173: Add gce setting in mmsys and display node
arm64: dts: mt7622: add built-in Wi-Fi device nodes
Link: https://lore.kernel.org/r/2794a8db-c14f-ac34-9e28-9f3700db6c4c@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:41:15 +0000 (22:41 +0200)]
Merge tag 'ux500-dts-v5.8' of git://git./linux/kernel/git/linusw/linux-stericsson into arm/dt
Ux500 DTS updates for the v5.8 kernel series:
- Add proximity sensor and magnetometer to the Samsung Golden
devicetree.
- Add magnetometer and touchscreen to the Samsung Skomer
devicetree.
* tag 'ux500-dts-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: ux500: Add touchscreen to the Skomer
ARM: dts: ux500: samsung-skomer: Add magnetometer
ARM: dts: ux500: samsung-golden: Add magnetometer
ARM: dts: ux500: samsung-golden: Add proximity sensor
Link: https://lore.kernel.org/r/CACRpkdbukO33SxAZ_yn-1N8=hq3hF5OBOtP_V0fbjRT-fAa87A@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:40:27 +0000 (22:40 +0200)]
Merge tag 'v5.7-next-dts32' of git://git./linux/kernel/git/matthias.bgg/linux into arm/dt
MT2701:
- add MUSB device to the SoC and the EVB
MT7623:
- add Mali-450 device node and bindings
- add phy to gmac2
* tag 'v5.7-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm: dts: mt2701: Add usb2 device nodes
dt-bindings: gpu: mali-utgard: add mediatek, mt7623-mali compatible
arm: dts: mt7623: add Mali-450 device node
arm: dts: mt7623: add phy-mode property for gmac2
Link: https://lore.kernel.org/r/ec17cf62-5463-9537-6618-2db9b2b5036e@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:39:46 +0000 (22:39 +0200)]
Merge tag 'socfpga_dts_update_for_v5.8' of git://git./linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.8
- Leave the FPGA bridges disabled in base dtsi
- Add fpga2hps and fpga2sdram bridges on base Cyclone5/Arria5 dtsi
* tag 'socfpga_dts_update_for_v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add fpga2hps and fpga2sdram bridges
ARM: dts: socfgpa: set bridges status to disabled
Link: https://lore.kernel.org/r/20200515193029.11318-2-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:35:34 +0000 (22:35 +0200)]
Merge tag 'sunxi-dt-for-5.8-1' of git://git./linux/kernel/git/sunxi/linux into arm/dt
Our usual number of patches to improve the Allwinner Device Tree
support, including:
- Support for the IOMMU on the H6
- Support for cpufreq / thermal throttling on the H6
- Support for the mailbox on the A64, A83t, H3, H5 and H6
- New boards: A20-OLinuXino-LIME-eMMC
* tag 'sunxi-dt-for-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (23 commits)
arm64: dts: allwinner: h6: Add IOMMU
arm64: dts: allwinner: h6: Enable CPU opp tables for Tanix TX6
arm64: dts: allwinner: h6: add voltage range to OPP table
arm64: dts: allwinner: sun50i-a64: Add missing address/size-cells
arm64: dts: allwinner: h6: Enable CPU opp tables for Pine H64
arm64: dts: allwinner: Sort Pine H64 device-tree nodes
arm64: dts: allwinner: h6: Enable CPU opp tables for Orange Pi 3
arm64: dts: allwinner: h6: Enable CPU opp tables for Beelink GS1
arm64: dts: allwinner: h6: Add CPU Operating Performance Points table
arm64: dts: allwinner: h6: Add thermal trip points/cooling map
arm64: dts: allwinner: h6: Add clock to CPU cores
arm64: allwinner: h6: orangepi-lite2: Support BT+WIFI combo module
arm64: dts: allwinner: h6: orangepi: Disable OTG mode
arm64: dts: allwinner: h6: orangepi: Add gpio power supply
ARM: dts: sun8i-h2-plus-bananapi-m2-zero: Fix led polarity
arm64: dts: allwinner: h6: Add msgbox node
arm64: dts: allwinner: a64: Add msgbox node
ARM: dts: sunxi: h3/h5: Add msgbox node
ARM: dts: sunxi: a83t: Add msgbox node
ARM: dts: sun8i-h3: add opp table for mali gpu
...
Link: https://lore.kernel.org/r/cfa66bd9-f74c-4614-9ea5-9ef8546cc571.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:34:59 +0000 (22:34 +0200)]
Merge tag 'tegra-for-5.8-arm-dt' of git://git./linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.8-rc1
This contains a bit of cleanup and CPU frequency scaling support for the
Tegra30 Beaver board.
* tag 'tegra-for-5.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra30: beaver: Add CPU Operating Performance Points
ARM: dts: tegra30: beaver: Set up voltage regulators for DVFS
ARM: tegra: Kill off "simple-panel" compatibles
Link: https://lore.kernel.org/r/20200515145311.1580134-11-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 20:30:18 +0000 (22:30 +0200)]
Merge tag 'tegra-for-5.8-dt-bindings' of git://git./linux/kernel/git/tegra/linux into arm/dt
dt-bindings: Changes for v5.8-rc1
This adds bindings for the CSI TPG clock on Tegra210, moves various
clocks from the clock and reset controller to the PMC where their
controls really are, adds bindings for the external memory controller
and video capture controller on Tegra210, as well as CPU frequency
scaling on Tegra20 and Tegra30.
* tag 'tegra-for-5.8-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: i2c: tegra: Document Tegra210 VI I2C
dt-bindings: tegra: Add VI and CSI bindings
dt-bindings: cpufreq: Add binding for NVIDIA Tegra20/30
dt-bindings: memory: tegra: Add external memory controller binding for Tegra210
dt-bindings: clock: tegra: Remove PMC clock IDs
dt-bindings: clock: tegra: Add clock ID for CSI TPG clock
Link: https://lore.kernel.org/r/20200515145311.1580134-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 14:03:55 +0000 (16:03 +0200)]
Merge tag 'ti-k3-dt-for-v5.8' of git://git./linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC DT updates for v5.8
- Add DSS support for both AM65x and J721e
- Add watchdog support for J721e
- Add EHRPWM support for AM65x
- Add Thermal support for AM65x
* tag 'ti-k3-dt-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: ti: k3-j721e-main: Add main domain watchdog entries
arm64: dts: ti: k3-am65-main: Add ehrpwm nodes
arm64: dts: ti: am654: Add thermal zones
arm64: dts: ti: am65-wakeup: Add VTM node
arm64: dts: ti: k3-j721e-common-proc-board: add assigned clks for DSS
arm64: dts: ti: k3-j721e-main: Add DSS node
arm64: dts: ti: am654: Add DSS node
Link: https://lore.kernel.org/r/7484d3c9-323f-36a3-f0df-1287586f356d@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 14:03:21 +0000 (16:03 +0200)]
Merge tag 'renesas-dt-bindings-for-v5.8-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.8 (take two)
- Document support for the RZ/G1H-based iWave RainboW Qseven SOM
(G21M) and board (G21D).
* tag 'renesas-dt-bindings-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: arm: renesas: Document iW-RainboW-G21D-Qseven-RZG1H board
dt-bindings: arm: renesas: Document iW-RainboW-G21M-Qseven-RZG1H SoM
Link: https://lore.kernel.org/r/20200515100547.14671-6-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 14:02:11 +0000 (16:02 +0200)]
Merge tag 'renesas-arm-dt-for-v5.8-tag2' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8 (take two)
- Initial support for the Renesas RZ/G1H SoC on the iWave RainboW
Qseven SOM (G21M) and board (G21D),
- Support for the AISTARVISION MIPI Adapter V2.1 camera board on the
Silicon Linux EK874 RZ/G2E evaluation kit.
* tag 'renesas-arm-dt-for-v5.8-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: r8a774c0-cat874: Add support for AISTARVISION MIPI Adapter V2.1
ARM: dts: r8a7742: Add GPIO nodes
ARM: dts: r8a7742: Add [H]SCIF{A|B} support
ARM: dts: r8a7742: Add IRQC support
ARM: dts: r8a7742-iwg21d-q7: Add iWave G21D-Q7 board based on RZ/G1H
ARM: dts: r8a7742-iwg21m: Add iWave RZ/G1H Qseven SOM
ARM: dts: r8a7742: Initial SoC device tree
clk: renesas: Add r8a7742 CPG Core Clock Definitions
dt-bindings: power: rcar-sysc: Add r8a7742 power domain index macros
Link: https://lore.kernel.org/r/20200515100547.14671-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 14:00:46 +0000 (16:00 +0200)]
Merge tag 'stm32-dt-for-v5.8-1' of git://git./linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v5.8, round 1
Highlights:
----------
MCU part:
-fix a typo for DAC io-channel-cells on f429 and h743
MPU part:
-Generic:
-Bump tp PSCI 1.0
-Fix a typo for DAC io-channel-cells
-Add M4 pdds for deep sleep mode
-Add I2C fatmode plus support
-Add new Octavio lxa-mc1 board based on OSDMP15x SiP
-Add new Stinger96 board support. It is a 96Boards IoT Extended board
based on stm32mp157a SoC. Some figures: 256MB DDR, 125MB and flash,
Onboard BG96 modem...
-Add IoT Box board support based on stinger96 board + Wifi/BT, CCS811
VOC sensor, 2 digitals microphones ...
-DH:
-Adapt dhcom-som and dhcom-pdk2 dts(i) files to STM32MP15 SoC diversity
-Add GPIO led and GPIO keys support on PDK2 board
-AV96:
-Major rework to support official avenger96 board based on DHCOR SOM.
-Prototype board is no more supported
* tag 'stm32-dt-for-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (58 commits)
ARM: dts: stm32: Split Avenger96 into DHCOR SoM and Avenger96 board
ARM: dts: stm32: Split SoC-independent parts of DHCOM SOM and PDK2
ARM: dts: stm32: Add GPIO LEDs for STM32MP1 DHCOM PDK2
ARM: dts: stm32: Add GPIO keys for STM32MP1 DHCOM PDK2
ARM: dts: stm32: Add IoT Box board support
dt-bindings: arm: stm32: Document IoT Box compatible
ARM: dts: stm32: Add Stinger96 board support
dt-bindings: arm: stm32: Document Stinger96 compatible
ARM: dts: stm32: Add missing pinctrl entries for STM32MP15
dt-bindings: Add vendor prefix for Shiratech Solutions
ARM: dts: stm32: Add bindings for SPI2 on AV96
ARM: dts: stm32: Add alternate pinmux for SPI2 pins
ARM: dts: stm32: Add bindings for ADC on AV96
ARM: dts: stm32: Add alternate pinmux for ADC pins
ARM: dts: stm32: Add bindings for FDCAN2 on AV96
ARM: dts: stm32: Add alternate pinmux for FDCAN2 pins
ARM: dts: stm32: Add bindings for FDCAN1 on AV96
ARM: dts: stm32: Add alternate pinmux for FDCAN1 pins
ARM: dts: stm32: Repair I2C2 operation on AV96
ARM: dts: stm32: Add alternate pinmux for I2C2 pins
...
Link: https://lore.kernel.org/r/19160355-364d-170c-7ae2-5ba7f714103f@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 13:51:39 +0000 (15:51 +0200)]
Merge tag 'samsung-dt-5.8' of git://git./linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.8
1. Add DTS for Exynos4210-based Samsung Galaxy S2 (GT-I9100)
mobile phone,
2. Enable WiFi and Bluetooth in multiple boards,
3. Add new features to S5Pv210-based Aries family of mobile phones
(e.g. Samsung Galaxy S): necessary configuration for suspend, audio
support, USB mux, touch keys, panel, i2c-gpio adapters, FM radio, ADC,
4. Many minor fixes (e.g. GPIO polarity, interrupts).
* tag 'samsung-dt-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (29 commits)
ARM: dts: s5pv210: Set MAX8998 GPIO pulls on Aries boards
ARM: dts: s5pv210: Correct FIMC definitions
ARM: dts: s5pv210: Assign clocks to MMC devices on Aries boards
ARM: dts: s5pv210: Enable ADC on Aries boards
ARM: dts: s5pv210: Add an ADC node
ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards
ARM: dts: s5pv210: Add si470x FM radio to Galaxy S
ARM: dts: s5pv210: Add remaining i2c-gpio adapters to Aries boards
ARM: dts: s5pv210: Add panel support to Aries boards
ARM: dts: s5pv210: Add touchkey support to Aries boards
ARM: dts: s5pv210: Add FSA9480 support to Aries boards
ARM: dts: s5pv210: Add WM8994 support to Aries boards
ARM: dts: s5pv210: Disable pulls on GPIO I2C adapters for Aries
ARM: dts: s5pv210: Set keep-power-in-suspend for SDHCI1 on Aries
ARM: dts: s5pv210: Correct gpi pinctrl node name
ARM: dts: s5pv210: Add sleep GPIO configuration for Galaxy S
ARM: dts: s5pv210: Add sleep GPIO configuration for Fascinate4G
ARM: dts: s5pv210: Add helper define for sleep gpio config
ARM: dts: exynos: Enable WLAN support for the UniversalC210 board
ARM: dts: exynos: Enable WLAN support for the Rinato board
...
Link: https://lore.kernel.org/r/20200512122922.5700-2-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 13:45:59 +0000 (15:45 +0200)]
Merge tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux into arm/dt
This pull request contains Broadcom ARM-based SoCs Device Tree changes
for v5.8, please pull the following:
- Nicolas updates the Raspberry Pi 4 board DTS to include the GPIO
controlling power to the SD card, adds support for the vmmc regulator
for the emmc2 controller and finally updates the power management
provider for V3D to use the firmware to solve instabilities.
* tag 'arm-soc/for-5.8/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Use firmware PM driver for V3D
ARM: dts: bcm2711: Add vmmc regulator in emmc2
ARM: dts: bcm2711: Update expgpio's GPIO labels
Link: https://lore.kernel.org/r/20200511210522.28243-2-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 13:43:45 +0000 (15:43 +0200)]
Merge tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi into arm/dt
ARM64: DT: Hisilicon SoCs DT updates for 5.8
- Add pinconf for spi2 and spi3 nodes and increase the drive
strength to achieve the max speed for the Hikey960 board
- Add CTI nodes for the Hikey620 board
* tag 'hisi-arm64-dt-for-5.8' of git://github.com/hisilicon/linux-hisi:
arm64: dts: hi6220: Add CTI options
arm64: dts: hikey960: pinctrl: Fix spi2/spi3 pinconf
Link: https://lore.kernel.org/r/5EBE430E.6090508@hisilicon.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 10:34:22 +0000 (12:34 +0200)]
Merge tag 'realtek-dt-for-5.8' of git://git./linux/kernel/git/afaerber/linux-realtek into arm/dt
Realtek Arm based SoC DT for v5.8
Add RTD1195, RTD1395 and RTD1619 SoCs as well as Xnano X5 TV box.
Clean up memory nodes and /soc ranges. Factor out r-bus and partition it
into CRT, Iso, Misc, SB2 and SCPU Wrapper blocks.
* tag 'realtek-dt-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek: (35 commits)
dt-bindings: reset: rtd1295: Add SB2 reset
arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes
ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd16xx: Add CRT syscon node
ARM: dts: rtd1195: Add UART resets
ARM: dts: rtd1195: Add reset nodes
dt-bindings: reset: Add Realtek RTD1195
ARM: dts: rtd1195: Add CRT syscon node
arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon
arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon
arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon
ARM: dts: rtd1195: Introduce iso and misc syscon
arm64: dts: realtek: rtd1295: Add Xnano X5
dt-bindings: arm: realtek: Add Xnano X5
dt-bindings: vendor-prefixes: Add Xnano
arm64: dts: realtek: rtd16xx: Add memory reservations
arm64: dts: realtek: rtd16xx: Carve out boot ROM from memory
arm64: dts: realtek: Add RTD1619 SoC and Realtek Mjolnir EVB
...
Link: https://lore.kernel.org/r/20200510232158.18477-2-afaerber@suse.de
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 10:19:04 +0000 (12:19 +0200)]
Merge tag 'aspeed-5.8-devicetree' of git://git./linux/kernel/git/joel/aspeed into arm/dt
ASPEED device tree updates for 5.8
New machines:
- YADRO's ast2500 OpenPower P9 Nicole BMC
- Facebook's ast2500 x86 Yosemite V2 BMC
The AST2600 machines Rainier and Tacoma were fleshed out.
Machines have started describing the GPIO names as userspace attempts
to use the GPIO chardev API.
* tag 'aspeed-5.8-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed: (32 commits)
ARM: dts: aspeed: Change KCS nodes to v2 binding
ARM: dts: Aspeed: AST2600: Add XDMA PCI-E root control reset
ARM: dts: aspeed: ast2600: Add XDMA Engine
ARM: dts: aspeed: ast2500: Add XDMA Engine
ARM: dts: aspeed: Adding Facebook Yosemite V2 BMC
ARM: dts: aspeed: Add YADRO Nicole BMC
ARM: dts: aspeed: mihawk: add aliases for i2c
ARM: dts: aspeed: tacoma: Add TPM
ARM: dts: aspeed: tacoma: Enable the second VUART
ARM: dts: aspeed: tacoma: Add iio-hwmon nodes for IIO devices
ARM: dts: aspeed: rainier: Add VGA reserved memory region
ARM: dts: aspeed: rainier: Add gpio line names
ARM: dts: aspeed: tacoma: Add gpio line names
ARM: dts: aspeed: zaius: Add gpio line names
ARM: dts: aspeed: romulus: Add gpio line names
ARM: dts: aspeed: witherspoon: Add gpio line names
ARM: dts: aspeed: ast2600: Set arch timer always-on
ARM: dts: aspeed: tacoma: Add GPIOs for FSI
ARM: dts: aspeed: mihawk: Change the name of leds
ARM: dts: aspeed: rainier: Remove regulators
...
Link: https://lore.kernel.org/r/CACPK8Xd-=XFREvvS-mK_ECyn14y0GPAMyy5BpEEUYfaw4jAgsw@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 10:03:23 +0000 (12:03 +0200)]
Merge tag 'omap-for-v5.8/dt-signed' of git://git./linux/kernel/git/tmlind/linux-omap into arm/dt
DTS changes for omaps for v5.8 merge window
We add support for beaglebone-ai board that's am5729 based devices.
Then we have a series changes to configure more hardware acceletators found
on omap variants. With the recent ti-sysc related changes, we can now better
configure the accelerators with help of the clock framework and reset driver.
So with a series of changes from Suman Anna and Tero Kristo, let's configure
IPUs and DSPs for dra7 devices like beagle-x15. And let's also configure the
missing crypto accelerators for omap5 as those have been missing.
Note that there are still some pending driver related patches to use IPU and
DSP related features with mainline kernel, but those are independent of the
devicetree changes.
Then there is a display related change for am57xx-idk for tc358778 bridge,
and a change to configure the missing clock source for some PWM timers.
* tag 'omap-for-v5.8/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (26 commits)
ARM: OMAP5: Make L4SEC clock domain SWSUP only
ARM: OMAP4: Make L4SEC clock domain SWSUP only
ARM: dts: omap5: add DES crypto accelerator node
ARM: dts: omap5: add SHA crypto accelerator node
ARM: dts: omap5: add aes2 entry
ARM: dts: omap5: add aes1 entry
ARM: dts: dra7-ipu-dsp-common: Add watchdog timers to IPU and DSP nodes
ARM: dts: am571x-idk: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: am572x-idk-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: beagle-x15-common: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra76-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra71-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm-revc: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra72-evm: Add CMA pools and enable IPUs & DSP1 rprocs
ARM: dts: dra7-evm: Add CMA pools and enable IPU & DSP rprocs
ARM: dts: dra7-ipu-dsp-common: Add timers to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Add mailboxes to IPU and DSP nodes
ARM: dts: dra7-ipu-dsp-common: Move mailboxes into common files
ARM: dts: DRA72x: Add aliases for rproc nodes
ARM: dts: DRA74x: Add aliases for rproc nodes
...
Link: https://lore.kernel.org/r/pull-1588873628-477615@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 09:55:28 +0000 (11:55 +0200)]
Merge tag 'renesas-dt-bindings-for-v5.8-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas DT binding updates for v5.8
- Document System Controller (SYSC) and Reset (RST) support for
RZ/G1H.
* tag 'renesas-dt-bindings-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
dt-bindings: reset: rcar-rst: Document r8a7742 reset module
dt-bindings: power: rcar-sysc: Document r8a7742 SYSC binding
Link: https://lore.kernel.org/r/20200430084849.1457-6-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 09:54:41 +0000 (11:54 +0200)]
Merge tag 'renesas-arm-dt-for-v5.8-tag1' of git://git./linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM DT updates for v5.8
- USB, UART, PWM, and PCIe support for R-Car M3-W+,
- PWM (16-bit Timer Pulse Unit and PWM Timers) support for R-Car M2-W,
- Minor fixes and cleanups.
* tag 'renesas-arm-dt-for-v5.8-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel:
arm64: dts: renesas: Fix IOMMU device node names
ARM: dts: renesas: Fix IOMMU device node names
ARM: dts: shmobile: Update CMT1 compatible values
ARM: dts: r8a7791: Add PWM device nodes
ARM: dts: r8a7791: Add TPU device node
arm64: dts: renesas: r8a77961: Add PCIe device nodes
arm64: dts: renesas: r8a77961: Add PWM device nodes
arm64: dts: renesas: r8a77961: Add SCIF and HSCIF nodes
arm64: dts: renesas: r8a77961: Add USB3.0 device nodes
arm64: dts: renesas: r8a77961: Add USB2.0 device nodes
Link: https://lore.kernel.org/r/20200430084849.1457-3-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 09:53:19 +0000 (11:53 +0200)]
Merge tag 'versatile-dts-v5.8-1' of git://git./linux/kernel/git/linusw/linux-integrator into arm/dt
Versatile DTS updates for the v5.8 kernel:
Create a new device tree for the Integrator/AP with the
IM-PD1 expansion module fitted in the first slot.
If we want to augment the slot where it is sitting, we can
alter the device tree or make the bootloader do so.
* tag 'versatile-dts-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Add devicetree for Integrator/AP with IM-PD1
Link: https://lore.kernel.org/r/CACRpkdZ-28o+pPdP7i_fc+7g4ndPWf+SWTsjnhFEegTggiXVSg@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Arnd Bergmann [Thu, 21 May 2020 09:51:28 +0000 (11:51 +0200)]
Merge tag 'sti-dt-for-v5.8-round1' of git://git./linux/kernel/git/pchotard/sti into arm/dt
STi DT fixes:
- Remove duplicated rng node in stih407-family.dtsi
- Fix complain about IRQ_TYPE_NONE usage in stih418.dtsi
* tag 'sti-dt-for-v5.8-round1' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
dts: arm: stih407-family: remove duplicated rng nodes
dts: arm: stih418: Fix complain about IRQ_TYPE_NONE usage
Link: https://lore.kernel.org/r/4b0c02e7-a247-50c0-d729-88d16b9dd7fd@st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chunyan Zhang [Tue, 14 Apr 2020 10:16:36 +0000 (18:16 +0800)]
arm64: dts: Add SC9863A emmc and sd card nodes
Add emmc and sd card devicetree nodes for SC9863A.
Link: https://lore.kernel.org/r/20200414101636.24503-3-zhang.lyra@gmail.com
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Chunyan Zhang [Tue, 14 Apr 2020 10:16:35 +0000 (18:16 +0800)]
arm64: dts: Add SC9863A clock nodes
add clock devicetree nodes for SC9863A.
Link: https://lore.kernel.org/r/20200414101636.24503-2-zhang.lyra@gmail.com
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Johan Jonker [Tue, 19 May 2020 11:14:44 +0000 (13:14 +0200)]
arm64: dts: rockchip: fix pinctrl-names for gpio-leds node on rk3326-odroid-go2
The 'pinctrl-names' property should contain a list of names
to the assigned states. The value 'led_pins' in the gpio-leds
node on rk3326-odroid-go2 is not a state that is normally used,
so change it the common name 'default'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200519111444.2208-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Tue, 28 Apr 2020 20:30:03 +0000 (22:30 +0200)]
arm64: dts: rockchip: fix pd_tcpc0 and pd_tcpc1 node position on rk3399
The pd_tcpc0 and pd_tcpc1 nodes are currently a sub node of pd_vio.
In the rk3399 TRM figure of the 'Power Domain Partition' and in the
table of 'Power Domain and Voltage Domain Summary' these power domains
are positioned directly under VD_LOGIC, so fix that in 'rk3399.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Caesar Wang <wxt@rock-chips.com>
Link: https://lore.kernel.org/r/20200428203003.3318-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Maulik Shah [Mon, 18 May 2020 12:20:02 +0000 (17:50 +0530)]
arm64: dts: qcom: sc7180: Correct the pdc interrupt ranges
Few PDC interrupts do not map to respective parent GIC interrupt.
Fix this by correcting the pdc interrupt map.
Fixes:
22f185ee81d2 ("arm64: dts: qcom: sc7180: Add pdc interrupt controller")
Cc: devicetree@vger.kernel.org
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1589804402-27130-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Alex Elder [Mon, 18 May 2020 21:49:39 +0000 (16:49 -0500)]
arm64: dts: qcom: sc7180: add IPA information
Add IPA-related nodes and definitions to "sc7180.dtsi".
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20200518214939.9730-1-elder@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Justin Swartz [Sun, 19 Apr 2020 12:51:33 +0000 (12:51 +0000)]
ARM: dts: rockchip: add rga node for rk322x
Add a node to define the presence of RGA, a 2D raster graphic
acceleration unit.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20200419125134.29923-2-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Justin Swartz [Mon, 6 Apr 2020 13:50:05 +0000 (13:50 +0000)]
ARM: dts: remove disable-wp from rk3229-xms6 emmc
Remove the disable-wp attribute from &emmc as it is, according to
Documentation/devicetree/bindings/mmc/mmc-controller.yaml:
"Not used in combination with eMMC or SDIO."
Suggested-by: Johan Jonker <jbx6244@gmail.com>
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20200406135006.23759-2-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Justin Swartz [Mon, 6 Apr 2020 13:50:04 +0000 (13:50 +0000)]
ARM: dts: enable WLAN for Mecer Xtreme Mini S6
The Mecer Xtreme Mini S6 features a wireless module, based on a
Realtek 8723BS, which provides WLAN and Bluetooth connectivity via
SDIO and UART interfaces respectively.
Define a simple MMC power sequence that declares the GPIO pins
connected to the module's WLAN Disable and Bluetooth Disable pins
as active low reset signals, because both signals must be deasserted
for WLAN radio operation.
Configure the host's SDIO interface for High Speed mode with 1.8v
I/O signalling and IRQ detection over a 4-bit wide bus.
Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
Link: https://lore.kernel.org/r/20200406135006.23759-1-justin.swartz@risingedge.co.za
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 16 Apr 2020 18:30:53 +0000 (20:30 +0200)]
arm64: dts: rockchip: add bus-width properties to mmc nodes for px30
'bus-width' and pinctrl containing the bus-pins
should be in the same file, so add them to
all mmc nodes in 'px30.dtsi'.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200416183053.6045-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Fri, 3 Apr 2020 18:01:56 +0000 (20:01 +0200)]
ARM: dts: rockchip: remove identical #include from rk3288.dtsi
There are 2 identical '#include' for 'rk3288-power.h',
so remove one of them.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200403180159.13387-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Tue, 28 Apr 2020 14:49:32 +0000 (16:49 +0200)]
ARM: dts: rockchip: rename and label gpio-led subnodes
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm/boot/dts/rk3188-radxarock.dt.yaml: gpio-leds:
'blue', 'green', 'sleep'
do not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Thu, 19 Dec 2019 12:19:54 +0000 (13:19 +0100)]
arm64: dts: rockchip: remove disable-wp from rk3308-roc-cc emmc node
The mmc-controller.yaml didn't explicitly say disable-wp is
for SD card slot only, but that is what it was designed for
in the first place.
Remove all disable-wp from emmc or sdio controllers.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20191219121954.2450-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Tue, 28 Apr 2020 14:49:33 +0000 (16:49 +0200)]
arm64: dts: rockchip: rename and label gpio-led subnodes
Current dts files with 'gpio-led' nodes were manually verified.
In order to automate this process leds-gpio.txt
has been converted to yaml. With this conversion a check
for pattern properties was added. A test with the command
below gives a screen full of warnings like:
arch/arm64/boot/dts/rockchip/rk3368-r88.dt.yaml: gpio-leds:
'work' does not match any of the regexes:
'(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Fix these errors with help of the following rules:
1: Add nodename in the preferred form.
2: Always add a label that ends with '_led' to prevent conflicts
with other labels such as 'power' and 'mmc'
3: If leds need pinctrl add a label that ends with '_led_pin'
also to prevent conflicts with other labels.
patternProperties:
# The first form is preferred, but fall back to just 'led'
# anywhere in the node name to at least catch some child nodes.
"(^led-[0-9a-f]$|led)":
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/leds/
leds-gpio.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428144933.10953-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Tue, 28 Apr 2020 20:30:02 +0000 (22:30 +0200)]
arm64: dts: rockchip: fix defines in pd_vio node for rk3399
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-evb.dt.yaml: pd_vio@15:
'pd_tcpc0@RK3399_PD_TCPC0', 'pd_tcpc1@RK3399_PD_TCPC1'
do not match any of the regexes:
'.*-names$', '.*-supply$', '^#.*-cells$',
'^#[a-zA-Z0-9,+\\-._]{0,63}$',
'^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}$',
'^[a-zA-Z][a-zA-Z0-9,+\\-._]{0,63}@[0-9a-fA-F]+(,[0-9a-fA-F]+)*$',
'^__.*__$', 'pinctrl-[0-9]+'
Fix error by replacing the wrong defines by the ones
mentioned in 'rk3399-power.h'.
make -k ARCH=arm64 dtbs_check
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200428203003.3318-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 21 Mar 2020 21:54:23 +0000 (22:54 +0100)]
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-orangepi
A test with the command below this error:
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dt.yaml: phy:
'#phy-cells' is a required property
'phy' is a reserved nodename and should not be used for pinctrl,
so change it to 'gmac'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 21 Mar 2020 21:54:22 +0000 (22:54 +0100)]
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-orangepi
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3399-orangepi.dt.yaml: phy@1:
'#phy-cells' is a required property
The phy nodename is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-5-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 21 Mar 2020 21:54:21 +0000 (22:54 +0100)]
arm64: dts: rockchip: fix &pinctrl phy sub nodename for rk3399-nanopi4
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dt.yaml: phy:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4.dt.yaml: phy:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-neo4.dt.yaml: phy:
'#phy-cells' is a required property
'phy' is a reserved nodename and should not be used for pinctrl,
so change it to 'gmac'.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 21 Mar 2020 21:54:20 +0000 (22:54 +0100)]
arm64: dts: rockchip: fix rtl8211e nodename for rk3399-nanopi4
A test with the command below gives these errors:
arch/arm64/boot/dts/rockchip/rk3399-nanopc-t4.dt.yaml: phy@1:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-m4.dt.yaml: phy@1:
'#phy-cells' is a required property
arch/arm64/boot/dts/rockchip/rk3399-nanopi-neo4.dt.yaml: phy@1:
'#phy-cells' is a required property
The rtl8211e node is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 21 Mar 2020 21:54:19 +0000 (22:54 +0100)]
arm64: dts: rockchip: fix rtl8211f nodename for rk3328 Beelink A1
A test with the command below gives this error:
arch/arm64/boot/dts/rockchip/rk3328-a1.dt.yaml: phy@0:
'#phy-cells' is a required property
The rtl8211f node is used by a phy-handle.
The parent node is compatible with "snps,dwmac-mdio",
so change nodename to 'ethernet-phy', for which '#phy-cells'
is not a required property.
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Sat, 21 Mar 2020 21:54:18 +0000 (22:54 +0100)]
arm64: dts: rockchip: fix phy nodename for rk3328
A test with the command below gives for example this error:
arch/arm64/boot/dts/rockchip/rk3328-evb.dt.yaml: phy@0:
'#phy-cells' is a required property
The phy nodename is normally used by a phy-handle.
This node is however compatible with
"ethernet-phy-id1234.d400", "ethernet-phy-ieee802.3-c22"
which is just been added to 'ethernet-phy.yaml'.
So change nodename to 'ethernet-phy' for which '#phy-cells'
is not a required property
make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=~/.local/lib/python3.5/site-packages/dtschema/schemas/
phy/phy-provider.yaml
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200321215423.12176-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Tue, 12 May 2020 20:35:24 +0000 (22:35 +0200)]
include: dt-bindings: rockchip: remove unused defines
The Rockchip dtsi and dts files have been bulk-converted for the
remaining raw gpio numbers into their descriptive counterparts and
also got rid of the unhelpful RK_FUNC_x -> x and RK_GPIOx -> x
mappings, so remove the unused defines in 'rockchip.h' to prevent
that someone start using them again.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200512203524.7317-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Johan Jonker [Tue, 12 May 2020 20:35:22 +0000 (22:35 +0200)]
arm64: dts: rockchip: replace RK_FUNC defines in rk3326-odroid-go2
The defines RK_FUNC_1 and RK_FUNC_2 are deprecated,
so replace them with the preferred form.
Restyle properties in the same line.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20200512203524.7317-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Bjorn Andersson [Mon, 18 May 2020 18:44:57 +0000 (11:44 -0700)]
arm64: dts: qcom: sc7180: Fix ETMv4 power management patch
The lack of unique context in '
0f1decaa83b7 ("arm64: dts: qcom: sc7180:
Support ETMv4 power management")' caused the patch to be applied
off-by-one. Move the "arm,coresight-loses-context-with-cpu" properties
down one node, so that it applies to the ETMs and not the replicator.
Reported-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Andre Przywara [Wed, 13 May 2020 10:30:14 +0000 (11:30 +0100)]
arm64: dts: juno: Fix SCPI shared mem node name
The SRAM DT binding requires child nodes to use a certain node name
scheme.
Change the naming from scp-shmem to scp-sram to comply with that.
Link: https://lore.kernel.org/r/20200513103016.130417-19-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:13 +0000 (11:30 +0100)]
arm64: dts: vexpress: Fix VExpress LED names
The common LED binding wants the LED node names to start with led- and
then have just a single number.
Changing the naming for the 8 user LEDs from using user<x> to led-<x>.
Also there is no default-trigger named "mmc0" in the kernel, so use the
more generic "disk-activity".
Link: https://lore.kernel.org/r/20200513103016.130417-18-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:12 +0000 (11:30 +0100)]
arm64: dts: juno: Fix GPU interrupt order
The Mali binding insists on the GPU interrupts to be in ordered as: job,
mmu, gpu.
Sort the GPU interrupts and interrupt-names properties accordingly.
Link: https://lore.kernel.org/r/20200513103016.130417-17-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:11 +0000 (11:30 +0100)]
arm64: dts: fvp/juno: Fix bus node names
Most Arm Ltd. boards are employing a layered bus structure, to map
the hardware design (SoC, motherboard, IOFPGA) and structure the DTs.
The "simple-bus" nodes only allow a limited set of node names. Switch
to use *-bus to be binding compliant.
This relies on a pending dt-schema.git fix for now:
https://github.com/devicetree-org/dt-schema/pull/38
Link: https://lore.kernel.org/r/20200513103016.130417-16-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:10 +0000 (11:30 +0100)]
arm64: dts: fvp: Fix SMMU DT node
The SMMU name in the RevC FVP DT file was not fully binding compliant.
Adjust the node name to match the binding's list of allowed names, also
shuffle the order of the interrupts to comply with the expected order.
Link: https://lore.kernel.org/r/20200513103016.130417-15-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:09 +0000 (11:30 +0100)]
arm64: dts: fvp/juno: Fix serial node names
The UARTs for all Arm Ltd. boards were using "uart" as their node name
stub.
Replace that with the required "serial" string, to comply with the PL011
DT binding.
Link: https://lore.kernel.org/r/20200513103016.130417-14-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:08 +0000 (11:30 +0100)]
arm64: dts: juno: Use proper DT node name for USB
The EHCI/OCHI DT binding requires to use "usb" as the node name stub.
Replace the existing name with "usb" to comply with the binding.
Link: https://lore.kernel.org/r/20200513103016.130417-13-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tudor Ambarus [Mon, 18 May 2020 11:49:21 +0000 (11:49 +0000)]
ARM: dts: at91: sama5d2_xplained: Add aliases for the dedicated I2C IPs
The sama5d2 SoC has two dedicated I2C IPs that are enabled on
sama5d2_xplained. Add alias for the i2c devices to not rely on
probe order for the i2c device numbering.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20200518114802.253660-1-tudor.ambarus@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Linus Walleij [Sat, 16 May 2020 21:29:13 +0000 (23:29 +0200)]
ARM: dts: ux500: Add touchscreen to the Skomer
This adds touchscreen support to the Ux500 Samsung
GT-S7710 "Skomer" mobile phone.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200516212913.485365-1-linus.walleij@linaro.org
Andre Przywara [Wed, 13 May 2020 10:30:07 +0000 (11:30 +0100)]
arm64: dts: fvp: Fix ITS node names and #msi-cells
The GIC ITS nodes in the fastmodel DTS files were not fully binding
compliant.
Use one of the allowed node names, also add the required #msi-cells
property for the older model.
Link: https://lore.kernel.org/r/20200513103016.130417-12-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:06 +0000 (11:30 +0100)]
arm64: dts: fvp: Fix GIC child nodes
The GIC DT nodes for the fastmodels were not fully compliant with the
DT binding, which has certain expectations about child nodes and their
size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Since the .dts files share interrupt nexus nodes across different
interrupt controllers (GICv2 vs. GICv3), we need to use the only
commonly allowed #address-size value of <1> for both.
Link: https://lore.kernel.org/r/20200513103016.130417-11-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:05 +0000 (11:30 +0100)]
arm64: dts: juno: Fix GIC child nodes
The GIC DT nodes for the Juno boards were not fully compliant with
the DT binding, which has certain expectations about child nodes and
their size and address cells values.
Use smaller #address-cells and #size-cells values, as the binding
requests, and adjust the reg properties accordingly.
This requires adjusting the interrupt nexus nodes as well, as one
field of the interrupt-map property depends on the GIC's address-size.
Link: https://lore.kernel.org/r/20200513103016.130417-10-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:04 +0000 (11:30 +0100)]
arm64: dts: fvp: Fix GIC compatible names
The GIC DT binding only allows certain combinations of DT compatible
strings. The somewhat awkward "arm,cortex-a15-gic", "arm,cortex-a9-gic"
is not among those.
Drop that combination of different "cortex" based strings used for the
models, and replace it with the more useful combination including
"arm,gic-400".
Link: https://lore.kernel.org/r/20200513103016.130417-9-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:03 +0000 (11:30 +0100)]
arm64: dts: juno: Fix mem-timer
The Juno's mem-timer DT node was not fully compliant with the DT binding,
which has certain expectation about child nodes and their size and
address cells values.
Use a cell size of 1, as the binding requests, and spell out the ranges
property to be binding compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-8-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:02 +0000 (11:30 +0100)]
arm64: dts: juno: Move fixed devices out of bus node
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, and the gpio keys to the
root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-7-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:01 +0000 (11:30 +0100)]
arm64: dts: fvp: Move fixed clocks out of bus node
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks to the root node, since they do not depend on any
busses.
Link: https://lore.kernel.org/r/20200513103016.130417-6-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Andre Przywara [Wed, 13 May 2020 10:30:00 +0000 (11:30 +0100)]
arm64: dts: vexpress: Move fixed devices out of bus node
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/motherboard-bus/refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, the leds and the config bus
subtree to the root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-5-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Marek Behún [Wed, 6 May 2020 19:29:16 +0000 (21:29 +0200)]
arm64: dts: armada-3720-turris-mox: fix SFP binding
The sfp compatible should be 'sff,sfp', not 'sff,sfp+'. We used patched
kernel where the latter was working.
Fixes:
7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Andre Przywara [Wed, 13 May 2020 10:29:59 +0000 (11:29 +0100)]
arm64: dts: fvp: Move fixed devices out of bus node
The devicetree compiler complains when DT nodes without a reg property
live inside a (simple) bus node:
Warning (simple_bus_reg): Node /bus@8000000/motherboard-bus/v2m_refclk32khz
missing or empty reg/ranges property
Move the fixed clocks, the fixed regulator, and the config bus subtree
to the root node, since they do not depend on any busses.
Link: https://lore.kernel.org/r/20200513103016.130417-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Marek Behún [Thu, 30 Apr 2020 23:11:44 +0000 (01:11 +0200)]
arm64: dts: armada-3720-turris-mox: forbid SDR104 on SDIO for FCC purposes
Use sdhci-caps-mask to forbid SDR104 mode on the SDIO capable SDHCI
controller. Without this the device cannot pass electromagnetic
interference certifications.
Fixes:
7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Andre Przywara [Wed, 13 May 2020 10:29:58 +0000 (11:29 +0100)]
arm64: dts: fvp/juno: Fix node address fields
The Arm Ltd. boards were using an outdated address convention in the DT
node names, by separating the high from the low 32-bits of an address by
a comma.
Remove the comma from the node name suffix to be DT spec compliant.
Link: https://lore.kernel.org/r/20200513103016.130417-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Brian J. Tarricone [Sat, 25 Apr 2020 19:28:20 +0000 (12:28 -0700)]
ARM: dts: kirkwood: ReadyNAS NV+v2: Add LCD panel
The NV+ v2 has a WH1602 LCD panel (which is just a rebranded HD44780),
similar to the Netgear RN104, just with different GPIO assignments.
Signed-off-by: Brian J. Tarricone <brian@tarricone.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Pawel Dembicki [Wed, 22 Apr 2020 15:00:06 +0000 (17:00 +0200)]
ARM: dts: kirkwood: Add Check Point L-50 board
This patch adds dts for the Check Point L-50 from 600/1100 series
routers.
Specification:
-CPU: Marvell Kirkwood 88F6821 1200MHz
-RAM: 512MB
-Flash: NAND 512MB
-WiFi: mPCIe card based on Atheros AR9287 b/g/n
-WAN: 1 Gigabit Port (Marvell 88E1116R PHY)
-LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4))
-USB: 2x USB2.0
-Express card slot
-SD card slot
-Serial console: RJ-45 115200 8n1
-Unsupported DSL
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Baruch Siach [Wed, 29 Apr 2020 04:30:35 +0000 (07:30 +0300)]
ARM: dts: marvell: drop i2c timeout-ms property
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Wed, 6 May 2020 09:40:37 +0000 (10:40 +0100)]
arm64: dts: add uDPU i2c bus recovery
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Baruch Siach [Wed, 29 Apr 2020 04:30:36 +0000 (07:30 +0300)]
arm64: dts: marvell: drop i2c timeout-ms property
The timeout-ms property for i2c master nodes is undocumented, and as
never been supported. Drop it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Pali Rohár [Thu, 30 Apr 2020 08:06:25 +0000 (10:06 +0200)]
arm64: dts: marvell: armada-37xx: Move PCIe max-link-speed property
Move the max-link-speed property of the PCIe node from board specific
device tree files to the generic armada-37xx.dtsi.
Armada 37xx supports only PCIe gen2 speed so max-link-speed property
should be in the generic armada-37xx.dtsi file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Thu, 30 Apr 2020 08:06:24 +0000 (10:06 +0200)]
arm64: dts: marvell: armada-37xx: Move PCIe comphy handle property
Move the comphy handle property of the PCIe node from board specific
device tree files (EspressoBin and Turris Mox) to the generic
armada-37xx.dtsi.
This is correct since this is the only possible PCIe PHY configuration
on Armada 37xx, so when PCIe is enabled on any board, this handle is
correct.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Marek Behún [Thu, 30 Apr 2020 08:06:23 +0000 (10:06 +0200)]
arm64: dts: marvell: armada-37xx: Set pcie_reset_pin to gpio function
We found out that we are unable to control the PERST# signal via the
default pin dedicated to be PERST# pin (GPIO2[3] pin) on A3700 SOC when
this pin is in EP_PCIE1_Resetn mode. There is a register in the PCIe
register space called PERSTN_GPIO_EN (
D0088004[3]), but changing the
value of this register does not change the pin output when measuring
with voltmeter.
We do not know if this is a bug in the SOC, or if it works only when
PCIe controller is in a certain state.
Commit
f4c7d053d7f7 ("PCI: aardvark: Wait for endpoint to be ready
before training link") says that when this pin changes pinctrl mode
from EP_PCIE1_Resetn to GPIO, the PERST# signal is asserted for a brief
moment.
So currently the situation is that on A3700 boards the PERST# signal is
asserted in U-Boot (because the code in U-Boot issues reset via this pin
via GPIO mode), and then in Linux by the obscure and undocumented
mechanism described by the above mentioned commit.
We want to issue PERST# signal in a known way, therefore this patch
changes the pcie_reset_pin function from "pcie" to "gpio" and adds the
reset-gpios property to the PCIe node in device tree files of
EspressoBin and Armada 3720 Dev Board (Turris Mox device tree already
has this property and uDPU does not have a PCIe port).
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Remi Pommarel <repk@triplefau.lt>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Russell King [Fri, 27 Mar 2020 12:40:42 +0000 (12:40 +0000)]
arm64: dts: update SolidRun Armada 8040 phy interface types
Update the SolidRun Armada 8040 platforms phy interface types from the
old 10gbase-kr to the newer and more correct 10gbase-r.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Min Guo [Wed, 11 Dec 2019 01:54:42 +0000 (09:54 +0800)]
arm: dts: mt2701: Add usb2 device nodes
Add musb nodes and usb2 phy nodes for MT2701
Signed-off-by: Min Guo <min.guo@mediatek.com>
Link: https://lore.kernel.org/r/20191211015446.11477-3-min.guo@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Sean Wang [Wed, 24 Jul 2019 09:01:00 +0000 (17:01 +0800)]
dt-bindings: gpu: mali-utgard: add mediatek, mt7623-mali compatible
The MediaTek MT7623 SoC contains a Mali-450, so add a compatible for it
and define its own vendor-specific properties.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/efeadefe3895bcadf1d2e9847b82206dd8c7ec35.1563867856.git.ryder.lee@mediatek.com
[mb: move to yaml file]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Ryder Lee [Wed, 24 Jul 2019 09:00:59 +0000 (17:00 +0800)]
arm: dts: mt7623: add Mali-450 device node
Add a node for Mali-450.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Link: https://lore.kernel.org/r/af7b5a2e00eb3a4b6262807c378e43afd5f74779.1563867856.git.ryder.lee@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Ulrich Hecht [Fri, 19 Jul 2019 09:50:16 +0000 (11:50 +0200)]
arm64: dts: mt8173: Add capacity-dmips-mhz attributes
Dhrystone benchmark on Acer Chromebook R13 CB5-312T:
A72:
15698587 dps @ 1807 MHz
A53: 7598784 dps @ 1703 MHz
Signed-off-by: Ulrich Hecht <uli-qwV78thtvt0@public.gmane.org>
Link: https://lore.kernel.org/r/1563529816-3992-1-git-send-email-uli@fpond.eu
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Chunfeng Yun [Tue, 11 Feb 2020 03:21:16 +0000 (11:21 +0800)]
arm64: dts: mt2712: use non-empty ranges for usb-phy
Use non-empty ranges for usb-phy to make the layout of
its registers clearer;
Replace deprecated compatible by generic
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Hsin-Yi Wang [Tue, 14 Apr 2020 03:08:14 +0000 (11:08 +0800)]
arm64: dts: mt8173: fix mdp aliases property name
Fix warning:
Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Link: https://lore.kernel.org/r/20200414030815.192104-1-hsinyi@chromium.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Manivannan Sadhasivam [Sat, 22 Feb 2020 16:24:44 +0000 (21:54 +0530)]
arm64: dts: mediatek: Switch to SPDX license identifier for MT6797 SoC
Switch to SPDX license identifier for MT6797 SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Manivannan Sadhasivam [Sat, 22 Feb 2020 16:24:43 +0000 (21:54 +0530)]
arm64: dts: mediatek: Enable I2C support for 96Boards X20 Development board
There are 7 I2C ports used on this board. Hence, enable all of them.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Manivannan Sadhasivam [Sat, 22 Feb 2020 16:24:42 +0000 (21:54 +0530)]
arm64: dts: mediatek: Add I2C support for MT6797 SoC
Add I2C support for Mediatek MT6797 SoC. There are a total of 8 I2C
controllers in this SoC (2 being shared) and they are same as the
controllers present in MT6577 SoC. Hence, the driver support is added with
DT fallback method.
As per the datasheet, there are controllers with _imm prefix like i2c2_imm
and i2c3_imm. These appears to be in different memory regions but sharing
the same pins with i2c2 and i2c3 respectively. Since there is no clear
evidence of what they really are, I've adapted the numbering/naming scheme
from the downstream code by Mediatek.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200222162444.11590-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Manivannan Sadhasivam [Sat, 22 Feb 2020 16:24:41 +0000 (21:54 +0530)]
dt-bindings: i2c: Document I2C controller binding for MT6797 SoC
I2C controller driver for MT6577 SoC is reused for MT6797 SoC. Hence,
document that in DT binding.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Wolfram Sang <wsa@kernel.org>
Link: https://lore.kernel.org/r/20200222162444.11590-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Sharat Masetty [Fri, 1 May 2020 10:30:35 +0000 (16:00 +0530)]
arm64: dts: qcom: sc7180: Add A618 gpu dt blob
This patch adds the required dt nodes and properties
to enabled A618 GPU.
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Link: https://lore.kernel.org/r/1588329036-18732-1-git-send-email-smasetty@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Sharat Masetty [Fri, 1 May 2020 10:30:36 +0000 (16:00 +0530)]
dt-bindings: arm-smmu: Add sc7180 compatible string
This patch simply adds a new compatible string for SC7180 platform.
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
Link: https://lore.kernel.org/r/1588329036-18732-2-git-send-email-smasetty@codeaurora.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Codrin Ciubotariu [Fri, 15 May 2020 14:00:01 +0000 (17:00 +0300)]
ARM: dts: at91: Configure I2C SCL gpio as open drain
The SCL gpio pin used by I2C bus for recovery needs to be configured as
open drain.
Fixes:
455fec938bbb ("ARM: dts: at91: sama5d2: add i2c gpio pinctrl")
Fixes:
a4bd8da893a3 ("ARM: dts: at91: sama5d3: add i2c gpio pinctrl")
Fixes:
8fb82f050cf6 ("ARM: dts: at91: sama5d4: add i2c gpio pinctrl")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20200515140001.287932-1-codrin.ciubotariu@microchip.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Michael Kao [Fri, 24 Apr 2020 08:23:40 +0000 (16:23 +0800)]
arm64: dts: mt8173: fix cooling device range
When thermal reaches target temperature,it would be pinned to state 0
(max frequency and power).
Fix the throttling range to no limit.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Link: https://lore.kernel.org/r/20200424082340.4127-1-michael.kao@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
projects / platform / kernel / linux-starfive.git / log