Axel Lin [Tue, 16 Apr 2013 15:29:12 +0000 (23:29 +0800)]
regulator: ab8500-ext: Don't update info->update_val if set_mode() fails
This ensures info->update_val status is still correct if set_mode() call fails.
Otherwise, get_mode() may return wrong status if a set_mode() call fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 9 Apr 2013 12:17:15 +0000 (20:17 +0800)]
regulator: ab8500: Don't update lp_mode_req flag in set_mode() error paths
Currently, set invalid mode setting for shared mode regulators may change
sm->lp_mode_req flag. This patch ensures we don't set lp_mode_req flag to wrong
status if set_mode() fails.
This patch includes some clean up, and these changes makes this patch looks like
code refactor. The clean up is mainly to avoid adding ugly code to handle
failure paths.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 9 Apr 2013 12:15:06 +0000 (20:15 +0800)]
regulator: ab8500: Don't update info->update_val if write to register fails
This patch ensures info->update_val is consistent with current register value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 10 Apr 2013 06:46:20 +0000 (14:46 +0800)]
regulator: ab8500: Optimize ab8540_aux3_regulator_get_voltage_sel
We can save a register read operation in some case if read
expand_register first.
If info->expand_register.voltage_mask bit is set, no need to read
voltage_reg.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 15 Apr 2013 08:36:51 +0000 (16:36 +0800)]
regulator: ab8500: Fix voltage_shift setting for AB8540_LDO_DMIC
The voltage_mask is 0xc0, thus we need to set voltage_shift = 6 to get correct
selector in get_voltage_sel and set_voltage_sel.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Fri, 12 Apr 2013 07:33:25 +0000 (15:33 +0800)]
regulator: ab8500: Fix voltage_mask for AB8505_LDO_AUDIO
The voltage_mask and voltage_shift settings of AB8505_LDO_AUDIO are not matched.
It looks like a typo in the voltage_mask settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 11 Apr 2013 04:05:43 +0000 (12:05 +0800)]
regulator: ab8500: Unregister ab8500-ext regulators in probe() failure path
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 11 Apr 2013 04:04:18 +0000 (12:04 +0800)]
regulator: ab8500-ext: Make the return type of ab8500_ext_regulator_exit() void
ab8500_ext_regulator_exit() never fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 7 Apr 2013 15:17:50 +0000 (23:17 +0800)]
regulator: ab8500-ext: Remove get_voltage to avoid duplicate implementation
The implementation of ab8500_ext_fixed_get_voltage is identical to
ab8500_ext_list_voltage. We can avoid the duplicate implementation by just
remove get_voltage. For fixed regulator, regulator core will call
list_voltage(rdev, 0) to get voltage if both get_voltage get_voltage_sel are
not implemented.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 7 Apr 2013 15:15:24 +0000 (23:15 +0800)]
regulator: ab8500-ext: Remove unnecessary checking for ab9540 and ab8540
This code was added by commit
0fe17e20a6
"regulator: ab8500-ext: Add support for AB9540 regulators"
and commit
bd44e2cb "regulator: ab8500: Also check for AB8505 based platforms"
The original patch[1] is to set info->desc.ops = &ab9540_ext_regulator_ops.
However, ab9540_ext_regulator_ops is identical to ab8500_ext_regulator_ops[2].
Thus we can complete remove the unnecessary checking for ab9540 and ab8540.
[1] https://lkml.org/lkml/2013/3/28/333
[2] https://lkml.org/lkml/2013/4/1/178
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 7 Apr 2013 15:13:39 +0000 (23:13 +0800)]
regulator: ab8500-ext: Get rid of is_enabled from struct ab8500_ext_regulator_info
The intention of this patch is to simplify the code.
Maintain the is_enabled flag is not trivial, it not only needs to set/clear the
flag in disable()/enable() but also needs to set the flag in is_enable() to get
initial status. The only benefit of keeping is_enabled flag is just save a
register read when set_mode(). Remove is_enabled flag makes the code simpler.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Sun, 7 Apr 2013 15:12:28 +0000 (23:12 +0800)]
regulator: ab8500: Get rid of is_enabled from struct ab8500_regulator_info
The intention of this patch is to simplify the code.
Maintain the is_enabled flag is not trivial, it not only needs to set/clear the
flag in disable()/enable() but also needs to set the flag in is_enable() to get
initial status. The only benefit of keeping is_enabled flag is just save a
register read when set_mode(). Remove is_enabled flag makes the code simpler.
This patch also moves ab8500_regulator_is_enabled() close to
ab8500_regulator_[en|dis]able functions.
This is required to avoid a forward declaration because now we call
ab8500_regulator_is_enabled() in ab8500_regulator_set_mode().
This change also makes the code better in readability by moving similar
functions to one place.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 3 Apr 2013 22:05:17 +0000 (06:05 +0800)]
regulator: ab8500: Remove ab8500_regulator_set_voltage_time_sel
All users of ab8500_regulator_volt_mode_ops and ab8500_regulator_volt_ops
do not set info->desc.enable_time, thus set_voltage_time_sel() always returns 0.
Remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 2 Apr 2013 12:24:23 +0000 (13:24 +0100)]
regulator: ab8500: Add missing volt_table setting for AB8540_LDO_TVOUT
This is required for regulator_list_voltage_table() to properly work.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 2 Apr 2013 12:24:22 +0000 (13:24 +0100)]
regulator: ab8500: Fix list_voltage for fixed voltage regulators
commit
b080c78a4e447e9c212c207f725999d4e32c5f19
"regulator: ab8500: Update voltage handling for fixed voltage regulators"
removes min_uV settings and sets volt_table for all fixed voltages, thus
we can not use regulator_list_voltage_linear now. Use
regulator_list_voltage_table instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:21 +0000 (13:24 +0100)]
ARM: ux500: Regulators: Bring the AB8500 regulator platform data up-to-date
Quite a few changes in this patch, including: supply-name changes, new
consumers, initialisation and capability updates and new regulators.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:20 +0000 (13:24 +0100)]
regulator: ab8500: Shuffle init functions into a more logical order
The ab*_match[] arrays should be moved out of the way, instead of
bunched in the middle of the initialisation functions. This patch
moves all initialisation code which currently resides above these
arrays down to be grouped with the others. This makes the whole
thing slightly easier to read.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:19 +0000 (13:24 +0100)]
ARM: ux500: Pass regulator platform data using the new format
Regulator platform data is now passed though a single structure
as opposed to the old way where four separate struct elements
were required. This patch makes use of the new format.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:18 +0000 (13:24 +0100)]
regulator: ab8500: Use regulator_list_voltage_table() to look-up voltages
The regulator framework offers a generic regulator_list_voltage_table()
function which can directly look-up a regulator's voltage capabilities
using a table provided through the desc structure. This patch ensures
that information is available.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:17 +0000 (13:24 +0100)]
regulator: ab8500: Remove the need for a 'delay' property
The regulator framework now has provisions to read a regulator's
start-up time via the 'enable_time' attribute. So let's remove all
'enable_time'/'delay' duplication and just stick with 'enable_time'
from now on.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:16 +0000 (13:24 +0100)]
regulator: ab8500: Set enable enable_time in regulator_desc
Allow the regulator framework to directly access the time it takes
any given regulator to settle. This saves time and code because
without it we would have to implement a dedication function to read
the value from elsewhere.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Zhenhua HUANG [Tue, 2 Apr 2013 12:24:15 +0000 (13:24 +0100)]
regulator: ab8500: Introduce aux5, aux6 regulators for AB8540
Introduce aux5, aux6 into ab8540 regulator framework.
Signed-off-by: Zhenhua HUANG <zhenhua.huang@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: David PARIS <david.paris@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:14 +0000 (13:24 +0100)]
regulator: ab8500: Use a struct to select the good regulator configuration
At the probe use a structure to select the good regulator array from
from ab9540, ab8505, ab8540 or ab8500 configuration.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 2 Apr 2013 12:56:16 +0000 (20:56 +0800)]
regulator: ab8500-ext: Don't update info->is_enabled if write to register fails
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 2 Apr 2013 13:08:24 +0000 (21:08 +0800)]
regulator: dbx500-prcmu: Remove operating_point from struct dbx500_regulator_info
operating_point is not used since the initial commit of db8500-prcmu driver,
remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:13 +0000 (13:24 +0100)]
regulator: ab8500: Update vdmic, vamic[1|2] parameters for AB8540
Add voltage setting for vdmic; add LP mode setting for vamic1,2.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:12 +0000 (13:24 +0100)]
regulator: ab8500: Add mode operation for v-amic
v-amic1 and v-amic2 regulators have dedicated mode registers
and share the same mode bit. This patch adds special handling
for those regulators.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:11 +0000 (13:24 +0100)]
regulator: ab8500: Add new operations for Vaux3
In former functions, only can set Vaux3 to 2.91V, because the
highest bit of Vaux3 register is put into another register. So
add new expanded functions for Vaux3's operation.
Signed-off-by: zhang xiaomei <xiaomei.zhang@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:10 +0000 (13:24 +0100)]
regulator: ab8500: Also check for AB8505 based platforms
Ensure we initialise AB8505 external supply regulators.
Signed-off-by: Alexandre Torgue <alexandre.torgue@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Tested-by: Xiao Mei ZHANG <xiaomei.zhang@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:09 +0000 (13:24 +0100)]
regulator: ab8500: Add voltage selection for AUDIO and ANA on AB8505
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rabin Vincent [Tue, 2 Apr 2013 12:24:08 +0000 (13:24 +0100)]
regulator: ab8500: Don't register external regulators on AB8505
ExtSupply regulators are not included on AB8505 based platforms.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Marcus COOPER <marcus.xm.cooper@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:07 +0000 (13:24 +0100)]
regulator: ab8500: Supply platform specific regulator id values
The regulator ID in the regulator info array should be the same
values as the position of the element within the array.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:06 +0000 (13:24 +0100)]
regulator: ab8500-ext: Add support for AB9540 regulators
Add the support for ab9540 external regulators.
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:05 +0000 (13:24 +0100)]
regulator: ab8500-ext: Remove unused REGULATOR_AB8500_EXT guard
Before the AB8500 External Regulator driver was Mainlined, it used
to be conditionally compiled in using the CONFIG_REGULATOR_AB8500_EXT
flag. During the review process that capability was removed, but the
guard controlling prototyping slipped though the net. This patch
cleans it up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Tue, 2 Apr 2013 12:24:04 +0000 (13:24 +0100)]
ARM: ux500: Use de-globalised version of id.h
Following commit: "7a4f260 ARM: ux500: de-globalize <mach/id.h>",
the use of 'mach/id.h' is no longer valid. This patch continues
the work of the aforementioned commit on patches applied around
the same time, containing the merge-conflict.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:18 +0000 (16:11 +0000)]
regulator: ab8500: Use regulator_list_voltage_table()
Following a recent move to regulator_list_voltage_table() for
all previous abx500 related platforms this converts all recent
platform updates over too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:17 +0000 (16:11 +0000)]
regulator: ab8500: Update voltage handling for fixed voltage regulators
There are a few over-lapping methods for voltage selection operating
in the AB8500 regulator driver currently. This patch removes unused,
unnecessary variables from the regulator_info structures and provides
voltage tables for those regulators which have fixed voltages.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:16 +0000 (16:11 +0000)]
regulator: ab8500: Add support for the ab8540
To obtain full AB8540 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:14 +0000 (16:11 +0000)]
regulator: ab8500: add support for ab8505
To obtain full AB8505 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bengt Jonsson [Thu, 28 Mar 2013 16:11:13 +0000 (16:11 +0000)]
regulator: ab8500-ext: Add support for AB8505/AB9540
The external regulator driver checks for old AB8500 HW
to apply a fix. This patch adds a check to see that
it is a AB8500 (not AB8505/AB9540).
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:12 +0000 (16:11 +0000)]
regulator: ab8500: Correct TVOUT regulator enable time
Update TVOUT regulator to match specification.
Was 10ms - changed to 500us.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:11 +0000 (16:11 +0000)]
regulator: ab8500: Add support for the ab9540
To obtain full AB9540 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:10 +0000 (16:11 +0000)]
regulator: ab8500: Prepare the driver for additional platforms
More platforms are to be supported by the AB8500 regulator driver,
so in this patch we prepare for their arrival. Instead of using
the AB8500 settings blindly, we provide an infrastructure where
adding a new platform is as easy as providing a couple of platform
specific data structures.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Thu, 28 Mar 2013 09:23:00 +0000 (17:23 +0800)]
regulator: ab8500: Update info->update_val only when successfully update register
Don't update info->update_val if write to the register fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:09 +0000 (16:11 +0000)]
regulator: ab8500: Init debug from regulator driver
The purpose of this patch is to guarantee that ab8500-debug will
record the regulator registers before they are modified by the
ab8500 regulator driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:08 +0000 (16:11 +0000)]
regulator: ab8500: Remove USB regulator
The USB regulator is controlled by hardware. The software support
was only needed for early hardware (ED) which is no longer supported.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bengt Jonsson [Thu, 28 Mar 2013 16:11:06 +0000 (16:11 +0000)]
regulator: ab8500-ext: Add HW request support
Support for HW request is added in the external regulator
driver. A flag in the board configuration can be set to
let HW control the regulator when there is no SW request.
This means that the regulator will be put in high power
mode when there is a SW request and in HW-request mode
otherwise.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:05 +0000 (16:11 +0000)]
ARM: ux500: Setup external regulator supply #2 for HREF v20 boards
v20 HREFs require non-standard configuration of EXT_SUPPLY2 to
function correctly (specific information is commented). Here we make
use of the recently added mechanism to adapt initialisation values
for such use-cases.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:04 +0000 (16:11 +0000)]
ARM: ux500: Turn off external regulator #1 when early HREFs suspend
When older variants of the HREF (earlier than v22) development
platform enter suspend mode, power down EXT_SUPPLY1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:03 +0000 (16:11 +0000)]
ARM: ux500: Provide a mechanism to over-ride regulator init values
If particular platforms require non-standard initialisation values,
they can use this function to adapt them as required.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:02 +0000 (16:11 +0000)]
ARM: ux500: Add regulator platform data for AB8500 external regulators
Pass constraint information for recently supported external AB8500
controlled regulators. Also change the start-up initialisation settings
for each of the 3 supported external supplies to low-power, off and
high-power for supply 1, 2 and 3 respectively.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 28 Mar 2013 16:11:01 +0000 (16:11 +0000)]
regulator: ab8500-ext: New driver to control external regulators
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:41 +0000 (15:59 +0000)]
regulator: ab8500: Amend the update value for AB8500_LDO_INTCORE regulator
The issues probably originated from a typo in the initial submission.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:21 +0000 (15:59 +0000)]
ARM: ux500: regulator: Add accelerometer and fix magnetometer supply device ID
This patch adds the LSM303DLHC Accelerometer to the list of VAUX1
consumers, as well as amending the already added LSM303DLHC
Magnetometer's device ID.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:15 +0000 (15:59 +0000)]
regulator: ab8500: Clean out SoC registers
Clean out initialisation that is handled by SoC. Regulator
settings for Vpll (partly), Vsmps1, Vsmps2, Vsmps3 (partly),
Vrf1, Varm, Vape, Vbb, Vmod are cleaned out. They should not
be touched by the kernel.
We also update many of the initialisation values to be more
in-line with the current development efforts of ST-Ericsson
internal engineers.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:14 +0000 (15:59 +0000)]
ARM: ux500: regulators: List the MMIO camera as a consumer of VAUX1
The MMIO camera uses the VAUX1 as it's voltage supply.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:13 +0000 (15:59 +0000)]
ARM: ux500: Add supply for the Cypress TrueTouch Touchscreen
This patch lists the Cypress TrueTouch Touchscreen as a consumer
of the AB8500 VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:12 +0000 (15:59 +0000)]
ARM: ux500: Add supply for the Pressure sensor
This patch lists the Pressure sensor as a consumer of the AB8500
VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:11 +0000 (15:59 +0000)]
ARM: ux500: Add supply for the Ambient light sensor device
This patch lists the Ambient light sensor device as a consumer
of the AB8500 VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:10 +0000 (15:59 +0000)]
ARM: ux500: Add supply for the L3G4200D Gyroscope
This patch lists the L3G4200D Gyroscope as a consumer of the
AB8500 VAUX1 regulator.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:05 +0000 (15:59 +0000)]
ARM: ux500: Update displays in vaux1 consumer list
Add 3 more specific consumers pertaining to the displays found
on the u8500 and ST User Interface Boards (UIBs).
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 27 Mar 2013 09:48:29 +0000 (17:48 +0800)]
regulator: ab8500: Remove set_voltage_time_sel and delay setting
The data sheet does not specify time delay for voltage selection,
thus remove set_voltage_time_sel and delay setting.
Note, currently set_voltage_time_sel callback returns 0 due to missing
delay settings.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Wed, 27 Mar 2013 09:47:22 +0000 (17:47 +0800)]
regulator: ab8500: Add missing enable_time settings
Base on the data provide by Bengt Jönsson, add below enable_time settings:
Worst case enable time from data sheet:
Vana: enable time = 140 us
Vaux1/2: enable time = 200 us
Vaux3: enable time = 450 us
Vintcore: enable time = 750 us
Vamic1/2: enable time = 500 us
Vdmic: enable time = 420 us
VTVout: enable time = 500 us
Vaudio: enable time = 140 us
Vusb: enable time = 150 us
This discussion thread is available at: https://lkml.org/lkml/2013/3/26/795
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Tue, 26 Mar 2013 08:13:14 +0000 (16:13 +0800)]
regulator: ab8500: Don't update is_enabled flag in error paths
This avoid setting is_enabled flag to wrong status if enable/disable fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 25 Mar 2013 06:59:00 +0000 (14:59 +0800)]
regulator: ab8500: Use regulator_list_voltage_linear for fixed voltage
Both ab8500_regulator_mode_ops and ab8500_regulator_ops do not have volt_table
setting, thus we can not use regulator_list_voltage_table for them.
However, they have min_uV setting with n_voltages = 1, so use
regulator_list_voltage_linear instead.
Also remove setting set_voltage_time_sel for ab8500_regulator_mode_ops.
It is used only for fixed voltage, so it does not need to implement
set_voltage_time_sel.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin [Mon, 25 Mar 2013 06:53:50 +0000 (14:53 +0800)]
regulator: ab8500: Fix build error
Fix below build error:
CC drivers/regulator/ab8500.o
drivers/regulator/ab8500.c:500:23: error: 'ab8500_regulator_fixed_ops' undeclared here (not in a function)
drivers/regulator/ab8500.c: In function 'ab8500_regulator_probe':
drivers/regulator/ab8500.c:972:8: warning: assignment from incompatible pointer type [enabled by default]
make[2]: *** [drivers/regulator/ab8500.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bengt Jonsson [Thu, 21 Mar 2013 15:59:03 +0000 (15:59 +0000)]
regulator: ab8500: Separate regulator and MFD platform data
The ab8500 MFD should not have knowledge about regulator-
specific platform data like number of regulators and
regulator registers. As the regulator platform data is
about to grow with external regulators, this information
is moved to a new structure provided by the regulator
driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Yvan FILLION <yvan.fillion@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:02 +0000 (15:59 +0000)]
regulator: ab8500: Another push to synchronise recent AB8500 developments
This patch ensures that many of the recent developments pertaining to
the AB8500 regulator device are propagated out into the public arena.
It aims to update some of the existing initialisation values in
accordance with internal ST-Ericsson code submissions. This single
patch was originally a collection of updates which have been squashed
together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:59:01 +0000 (15:59 +0000)]
ARM: ux500: regulators: Add mask for configuration
There is already before a register mask in the regulator driver
to allow some bits of a register to be initialized. The register
value is defined in the board configuration. This patch puts a
mask in the board configuration to specify which bits should
actually be altered. The purpose with this patch is to avoid
future mistakes when updating the allowed bits in the regulator
driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Bengt Jonsson [Thu, 21 Mar 2013 15:59:00 +0000 (15:59 +0000)]
regulator: ab8500: Added get_optimum_mode on regulators with idle mode
With this change, Vtvout, Vintcore12, Vaux1, 2 and 3 regulators
support DRMS (Dynamic Regulator Mode Switching) which will
dynamically handle requests for max current consumption from
several consumers and select a suitable regulator mode.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias WALLIN <mattias.wallin@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Emeric Vigier [Thu, 21 Mar 2013 15:58:59 +0000 (15:58 +0000)]
regulator: ab8500: Add set_mode/get_mode support
Signed-off-by: Ludovic Barré <ludovic.barre@stericsson.com>
Signed-off-by: Emeric Vigier <emeric.vigier@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Bengt JONSSON <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Lee Jones [Thu, 21 Mar 2013 15:58:58 +0000 (15:58 +0000)]
regulator: ab8500: Further populate initialisation registers
This patch supplies access to some extra settings provided by the
AB8500 regulator device. We also update some of the existing
initialisation values in accordance with internal ST-Ericsson code
submissions. This single patch was originally a collection of updates
which have been squashed together to aid with clarity.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Linus Torvalds [Sun, 17 Mar 2013 22:59:32 +0000 (15:59 -0700)]
Linux 3.9-rc3
David Rientjes [Sun, 17 Mar 2013 22:49:10 +0000 (15:49 -0700)]
perf,x86: fix link failure for non-Intel configs
Commit
1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") introduces a link failure since
perf_restore_debug_store() is only defined for CONFIG_CPU_SUP_INTEL:
arch/x86/power/built-in.o: In function `restore_processor_state':
(.text+0x45c): undefined reference to `perf_restore_debug_store'
Fix it by defining the dummy function appropriately.
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 17 Mar 2013 22:44:43 +0000 (15:44 -0700)]
perf,x86: fix wrmsr_on_cpu() warning on suspend/resume
Commit
1d9d8639c063 ("perf,x86: fix kernel crash with PEBS/BTS after
suspend/resume") fixed a crash when doing PEBS performance profiling
after resuming, but in using init_debug_store_on_cpu() to restore the
DS_AREA mtrr it also resulted in a new WARN_ON() triggering.
init_debug_store_on_cpu() uses "wrmsr_on_cpu()", which in turn uses CPU
cross-calls to do the MSR update. Which is not really valid at the
early resume stage, and the warning is quite reasonable. Now, it all
happens to _work_, for the simple reason that smp_call_function_single()
ends up just doing the call directly on the CPU when the CPU number
matches, but we really should just do the wrmsr() directly instead.
This duplicates the wrmsr() logic, but hopefully we can just remove the
wrmsr_on_cpu() version eventually.
Reported-and-tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 17 Mar 2013 18:04:14 +0000 (11:04 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"Eric's rcu barrier patch fixes a long standing problem with our
unmount code hanging on to devices in workqueue helpers. Liu Bo
nailed down a difficult assertion for in-memory extent mappings."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix warning of free_extent_map
Btrfs: fix warning when creating snapshots
Btrfs: return as soon as possible when edquot happens
Btrfs: return EIO if we have extent tree corruption
btrfs: use rcu_barrier() to wait for bdev puts at unmount
Btrfs: remove btrfs_try_spin_lock
Btrfs: get better concurrency for snapshot-aware defrag work
Liu Bo [Fri, 15 Mar 2013 14:46:39 +0000 (08:46 -0600)]
Btrfs: fix warning of free_extent_map
Users report that an extent map's list is still linked when it's actually
going to be freed from cache.
The story is that
a) when we're going to drop an extent map and may split this large one into
smaller ems, and if this large one is flagged as EXTENT_FLAG_LOGGING which means
that it's on the list to be logged, then the smaller ems split from it will also
be flagged as EXTENT_FLAG_LOGGING, and this is _not_ expected.
b) we'll keep ems from unlinking the list and freeing when they are flagged with
EXTENT_FLAG_LOGGING, because the log code holds one reference.
The end result is the warning, but the truth is that we set the flag
EXTENT_FLAG_LOGGING only during fsync.
So clear flag EXTENT_FLAG_LOGGING for extent maps split from a large one.
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Linus Torvalds [Sat, 16 Mar 2013 01:06:55 +0000 (18:06 -0700)]
Merge branch 'kbuild' of git://git./linux/kernel/git/mmarek/kbuild
Pull kbuild fix from Michal Marek:
"One fix for for make headers_install/headers_check to not require make
3.81. The requirement has been accidentally introduced in 3.7."
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: fix make headers_check with make 3.80
Linus Torvalds [Sat, 16 Mar 2013 01:05:37 +0000 (18:05 -0700)]
Merge tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux
Pull OpenRISC bug fixes from Jonas Bonn:
- The GPIO descriptor work has exposed how broken the non-GPIOLIB bits
for OpenRISC were. We now require GPIOLIB as this is the preferred
way forward.
- The system.h split introduced a bug in llist.h for arches using
asm-generic/cmpxchg.h directly, which is currently only OpenRISC.
The patch here moves two defines from asm-generic/atomic.h to
asm-generic/cmpxchg.h to make things work as they should.
- The VIRT_TO_BUS selector was added for OpenRISC, but OpenRISC does
not have the virt_to_bus methods, so there's a patch to remove it
again.
* tag 'for-3.9-rc3' of git://openrisc.net/jonas/linux:
openrisc: remove HAVE_VIRT_TO_BUS
asm-generic: move cmpxchg*_local defs to cmpxchg.h
openrisc: require gpiolib
Linus Torvalds [Sat, 16 Mar 2013 01:04:38 +0000 (18:04 -0700)]
Merge tag 'char-misc-3.9-rc2' of git://git./linux/kernel/git/gregkh/char-misc
Pull char/misc fixes from Greg Kroah-Hartman:
"Here are some tiny fixes for the w1 drivers and the final removal
patch for getting rid of CONFIG_EXPERIMENTAL (all users of it are now
gone from your tree, this just drops the Kconfig item itself.)
All have been in the linux-next tree for a while"
* tag 'char-misc-3.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
final removal of CONFIG_EXPERIMENTAL
w1: fix oops when w1_search is called from netlink connector
w1-gpio: fix unused variable warning
w1-gpio: remove erroneous __exit and __exit_p()
ARM: w1-gpio: fix erroneous gpio requests
Linus Torvalds [Sat, 16 Mar 2013 00:35:49 +0000 (17:35 -0700)]
Merge tag 'sound-3.9' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes, as expected for the middle rc:
- A couple of fixes for potential NULL dereferences and out-of-range
array accesses revealed by static code parsers
- A fix for the wrong error handling detected by trinity
- A regression fix for missing audio on some MacBooks
- CA0132 DSP loader fixes
- Fix for EAPD control of IDT codecs on machines w/o speaker
- Fix a regression in the HD-audio widget list parser code
- Workaround for the NuForce UDH-100 USB audio"
* tag 'sound-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix missing EAPD/GPIO setup for Cirrus codecs
sound: sequencer: cap array index in seq_chn_common_event()
ALSA: hda/ca0132 - Remove extra setting of dsp_state.
ALSA: hda/ca0132 - Check download state of DSP.
ALSA: hda/ca0132 - Check if dspload_image succeeded.
ALSA: hda - Disable IDT eapd_switch if there are no internal speakers
ALSA: hda - Fix snd_hda_get_num_raw_conns() to return a correct value
ALSA: usb-audio: add a workaround for the NuForce UDH-100
ALSA: asihpi - fix potential NULL pointer dereference
ALSA: seq: Fix missing error handling in snd_seq_timer_open()
Linus Torvalds [Sat, 16 Mar 2013 00:35:03 +0000 (17:35 -0700)]
Merge branch 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping
Pull DMA-mapping fix from Marek Szyprowski:
"An important fix for all ARM architectures which use ZONE_DMA.
Without it dma_alloc_* calls with GFP_ATOMIC flag might have allocated
buffers outsize DMA zone."
* 'fixes-for-3.9' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: DMA-mapping: add missing GFP_DMA flag for atomic buffer allocation
Linus Torvalds [Sat, 16 Mar 2013 00:34:01 +0000 (17:34 -0700)]
Merge tag 'mfd-fixes-3.9-1' of git://git./linux/kernel/git/sameo/mfd-fixes
Pull MFD fixes from Samuel Ortiz:
"This is the first batch of MFD fixes for 3.9.
With this one we have:
- An ab8500 build failure fix.
- An ab8500 device tree parsing fix.
- A fix for twl4030_madc remove routine to work properly (when
built-in).
- A fix for properly registering palmas interrupt handler.
- A fix for omap-usb init routine to actually write into the
hostconfig register.
- A couple of warning fixes for ab8500-gpadc and tps65912"
* tag 'mfd-fixes-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-fixes:
mfd: twl4030-madc: Remove __exit_p annotation
mfd: ab8500: Kill "reg" property from binding
mfd: ab8500-gpadc: Complain if we fail to enable vtvout LDO
mfd: wm831x: Don't forward declare enum wm831x_auxadc
mfd: twl4030-audio: Fix argument type for twl4030_audio_disable_resource()
mfd: tps65912: Declare and use tps65912_irq_exit()
mfd: palmas: Provide irq flags through DT/platform data
mfd: Make AB8500_CORE select POWER_SUPPLY to fix build error
mfd: omap-usb-host: Actually update hostconfig
Linus Torvalds [Sat, 16 Mar 2013 00:33:13 +0000 (17:33 -0700)]
Merge tag 'hwmon-for-linus' of git://git./linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Bug fixes for pmbus, ltc2978, and lineage-pem drivers
Added specific maintainer for some hwmon drivers"
* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (pmbus/ltc2978) Fix temperature reporting
hwmon: (pmbus) Fix krealloc() misuse in pmbus_add_attribute()
hwmon: (lineage-pem) Add missing terminating entry for pem_[input|fan]_attributes
MAINTAINERS: Add maintainer for MAX6697, INA209, and INA2XX drivers
Stephane Eranian [Fri, 15 Mar 2013 13:26:07 +0000 (14:26 +0100)]
perf,x86: fix kernel crash with PEBS/BTS after suspend/resume
This patch fixes a kernel crash when using precise sampling (PEBS)
after a suspend/resume. Turns out the CPU notifier code is not invoked
on CPU0 (BP). Therefore, the DS_AREA (used by PEBS) is not restored properly
by the kernel and keeps it power-on/resume value of 0 causing any PEBS
measurement to crash when running on CPU0.
The workaround is to add a hook in the actual resume code to restore
the DS Area MSR value. It is invoked for all CPUS. So for all but CPU0,
the DS_AREA will be restored twice but this is harmless.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Stephane Eranian <eranian@google.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Takashi Iwai [Fri, 15 Mar 2013 13:23:32 +0000 (14:23 +0100)]
ALSA: hda - Fix missing EAPD/GPIO setup for Cirrus codecs
During the transition to the generic parser, the hook to the codec
specific automute function was forgotten. This resulted in the silent
output on some MacBooks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dan Carpenter [Fri, 15 Mar 2013 06:14:22 +0000 (09:14 +0300)]
sound: sequencer: cap array index in seq_chn_common_event()
"chn" here is a number between 0 and 255, but ->chn_info[] only has
16 elements so there is a potential write beyond the end of the
array.
If the seq_mode isn't SEQ_2 then we let the individual drivers
(either opl3.c or midi_synth.c) handle it. Those functions all
do a bounds check on "chn" so I haven't changed anything here.
The opl3.c driver has up to 18 channels and not 16.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Arnd Bergmann [Thu, 14 Mar 2013 21:56:38 +0000 (22:56 +0100)]
mfd: twl4030-madc: Remove __exit_p annotation
4740f73fe5 "mfd: remove use of __devexit" removed the __devexit annotation
on the twl4030_madc_remove function, but left an __exit_p() present on the
pointer to this function. Using __exit_p was as wrong with the devexit in
place as it is now, but now we get a gcc warning about an unused function.
In order for the twl4030_madc_remove to work correctly in built-in code, we
have to remove the __exit_p.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Dylan Reid [Fri, 15 Mar 2013 00:27:46 +0000 (17:27 -0700)]
ALSA: hda/ca0132 - Remove extra setting of dsp_state.
spec->dsp_state is initialized to DSP_DOWNLOAD_INIT, no need to reset
and check it in ca0132_download_dsp().
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dylan Reid [Fri, 15 Mar 2013 00:27:45 +0000 (17:27 -0700)]
ALSA: hda/ca0132 - Check download state of DSP.
Instead of using the dspload_is_loaded() function, check the dsp_state
that is kept in the spec. The dspload_is_loaded() function returns
true if the DSP transfer was never started. This false-positive leads
to multiple second delays when ca0132_setup_efaults() times out on
each write.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dylan Reid [Fri, 15 Mar 2013 00:27:44 +0000 (17:27 -0700)]
ALSA: hda/ca0132 - Check if dspload_image succeeded.
If dspload_image() fails, it was ignored and dspload_wait_loaded() was
still called. dsp_loaded should never be set to true in this case,
skip it. The check in dspload_wait_loaded() return true if the DSP is
loaded or if it never started.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Michel Lespinasse [Thu, 14 Mar 2013 23:50:02 +0000 (16:50 -0700)]
mm/fremap.c: fix possible oops on error path
The vm_flags introduced in
6d7825b10dbe ("mm/fremap.c: fix oops on error
path") is supposed to avoid a compiler warning about unitialized
vm_flags without changing the generated code.
However I am concerned that this is going to be very brittle, and fail
with some compiler versions. The failure could be either of:
- compiler could actually load vma->vm_flags before checking for the
!vma condition, thus reintroducing the oops
- compiler could optimize out the !vma check, since the pointer just got
dereferenced shortly before (so the compiler knows it can't be NULL!)
I propose reversing this part of the change and initializing vm_flags to 0
just to avoid the bogus uninitialized use warning.
Signed-off-by: Michel Lespinasse <walken@google.com>
Cc: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Thu, 14 Mar 2013 21:53:07 +0000 (14:53 -0700)]
Merge branch 'rcu/urgent' of git://git./linux/kernel/git/paulmck/linux-rcu
Pull fix for hlist_entry_safe() regression from Paul McKenney:
"This contains a single commit that fixes a regression in
hlist_entry_safe(). This macro references its argument twice, which
can cause NULL-pointer errors. This commit applies a gcc statement
expression, creating a temporary variable to avoid the double
reference. This has been posted to LKML at
https://lkml.org/lkml/2013/3/9/75.
Kudos to CAI Qian, whose testing uncovered this, to Eric Dumazet, who
spotted root cause, and to Li Zefan, who tested this commit."
* 'rcu/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu:
list: Fix double fetch of pointer in hlist_entry_safe()
Paul E. McKenney [Sat, 9 Mar 2013 15:38:41 +0000 (07:38 -0800)]
list: Fix double fetch of pointer in hlist_entry_safe()
The current version of hlist_entry_safe() fetches the pointer twice,
once to test for NULL and the other to compute the offset back to the
enclosing structure. This is OK for normal lock-based use because in
that case, the pointer cannot change. However, when the pointer is
protected by RCU (as in "rcu_dereference(p)"), then the pointer can
change at any time. This use case can result in the following sequence
of events:
1. CPU 0 invokes hlist_entry_safe(), fetches the RCU-protected
pointer as sees that it is non-NULL.
2. CPU 1 invokes hlist_del_rcu(), deleting the entry that CPU 0
just fetched a pointer to. Because this is the last entry
in the list, the pointer fetched by CPU 0 is now NULL.
3. CPU 0 refetches the pointer, obtains NULL, and then gets a
NULL-pointer crash.
This commit therefore applies gcc's "({ })" statement expression to
create a temporary variable so that the specified pointer is fetched
only once, avoiding the above sequence of events. Please note that
it is the caller's responsibility to use rcu_dereference() as needed.
This allows RCU-protected uses to work correctly without imposing
any additional overhead on the non-RCU case.
Many thanks to Eric Dumazet for spotting root cause!
Reported-by: CAI Qian <caiqian@redhat.com>
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Li Zefan <lizefan@huawei.com>
Linus Torvalds [Thu, 14 Mar 2013 19:11:28 +0000 (12:11 -0700)]
Merge branch 'for_linus' of git://git./linux/kernel/git/jack/linux-fs
Pull ext2, ext3, reiserfs, quota fixes from Jan Kara:
"A fix for regression in ext2, and a format string issue in ext3. The
rest isn't too serious."
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2: Fix BUG_ON in evict() on inode deletion
reiserfs: Use kstrdup instead of kmalloc/strcpy
ext3: Fix format string issues
quota: add missing use of dq_data_lock in __dquot_initialize
Liu Bo [Wed, 13 Mar 2013 13:43:03 +0000 (07:43 -0600)]
Btrfs: fix warning when creating snapshots
Creating snapshot passes extent_root to commit its transaction,
but it can lead to the warning of checking root for quota in
the __btrfs_end_transaction() when someone else is committing
the current transaction. Since we've recorded the needed root
in trans_handle, just use it to get rid of the warning.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Wang Shilong [Wed, 6 Mar 2013 11:51:47 +0000 (11:51 +0000)]
Btrfs: return as soon as possible when edquot happens
If one of qgroup fails to reserve firstly, we should return immediately,
it is unnecessary to continue check.
Signed-off-by: Wang Shilong <wangsl-fnst@cn.fujitsu.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Josef Bacik [Fri, 8 Mar 2013 20:41:02 +0000 (15:41 -0500)]
Btrfs: return EIO if we have extent tree corruption
The callers of lookup_inline_extent_info all handle getting an error back
properly, so return an error if we have corruption instead of being a jerk and
panicing. Still WARN_ON() since this is kind of crucial and I've been seeing it
a bit too much recently for my taste, I think we're doing something wrong
somewhere. Thanks,
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Eric Sandeen [Sat, 9 Mar 2013 15:18:39 +0000 (15:18 +0000)]
btrfs: use rcu_barrier() to wait for bdev puts at unmount
Doing this would reliably fail with -EBUSY for me:
# mount /dev/sdb2 /mnt/scratch; umount /mnt/scratch; mkfs.btrfs -f /dev/sdb2
...
unable to open /dev/sdb2: Device or resource busy
because mkfs.btrfs tries to open the device O_EXCL, and somebody still has it.
Using systemtap to track bdev gets & puts shows a kworker thread doing a
blkdev put after mkfs attempts a get; this is left over from the unmount
path:
btrfs_close_devices
__btrfs_close_devices
call_rcu(&device->rcu, free_device);
free_device
INIT_WORK(&device->rcu_work, __free_device);
schedule_work(&device->rcu_work);
so unmount might complete before __free_device fires & does its blkdev_put.
Adding an rcu_barrier() to btrfs_close_devices() causes unmount to wait
until all blkdev_put()s are done, and the device is truly free once
unmount completes.
Cc: stable@vger.kernel.org
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>
Liu Bo [Mon, 11 Mar 2013 09:37:45 +0000 (09:37 +0000)]
Btrfs: remove btrfs_try_spin_lock
Remove a useless function declaration
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>